IPS e.max CAD C16
IPS e.max CAD C16 Larger Size Block Low translucency Shades: A1, A2, A3, A3.5, B1, B2, C1, C2, D2, BL2 Indicated for single unit restorations Full and partial coverage single units Large canines Restorations over custom abutments
IPS e.max CAD 3-unit bridge
Instructions for Use Ordering # for Flow chart - 662640
Indications / contraindications Indications Up to three-unit bridges up to the second premolar as the abutment tooth Contraindications Inlay bridges Parafunction (e.g. bruxism) Cantilever bridges Maryland bridges Pontic width > 11 mm in the anterior region Pontic width > 9 mm in the premolar region Any other use not listed as an indication for IPS e.max CAD
Connector Dimensions Dimensions: 16 mm 2 Height >= Width Important: Currently, the new CEREC 4.2 software does NOT have a tool to measure the area of the connector The new E4D Software will have a measuring tool
Processing options
Staining technique using IPS e.max CAD Crystall
Staining technique Bridge after CAD/CAM milling approximately 8 minutes per unit = 24 minutes Actual times may vary Smooth out the attachment point and take proximal contacts into account.
Staining technique Do not use diamond discs for finishing, since this may result in predetermined breaking points. Finish interdental areas with fine-grit diamonds (grit size 40 50 µm). Make sure to observe the connector dimensions.
Staining technique Check occlusion, articulation and proximal contacts. Surface-grind the outer surface, particularly the functional areas of the restoration, with a fine diamond to smooth out the surface structure created by the CAD/CAM process.
Staining technique Use the largest possible IPS e.max CAD Crystallization Pin for crystallization. Fill the inside of the crowns of the previously cleaned bridge with IPS Object Fix Putty or Flow and press the appropriate IPS e.max CAD Crystallization Pin deeply into the IPS Object Fix material.
Staining technique Place the bridge on the IPS e.max CAD Crystallization Tray immediately. Smooth out displaced IPS Object Fix Putty or Flow with a plastic spatula from the margin towards the support pin so that the pin is secured in the paste and the crown wall is precisely supported.
Staining technique Clean off any possible residue adhering to the outer surface of the restoration with a brush moistened with water and then dry. Apply IPS e.max CAD Crystall./Glaze paste evenly to the blue restoration. Apply the mixed IPS e.max CAD Crystall./ Shades and Stains into the unfired IPS e.max CAD Crystall./Glaze paste.
Combination Firing Glaze & Crystallize P1 Use Program P1 Place the IPS e.max CAD Crystallization Tray with the glazed and stained restoration in the furnace and conduct the combination firing.
Correction Firing Use P1 Use Program P1 If adjustments are required (shade, glaze, contact points), conduct a separate corrective firing cycle on the IPS e.max CAD Crystallization Tray.
Staining technique Completed IPS e.max CAD LT bridge.
Firing parameters
Cementation
Conditioning of the restoration Do not blast the restorations with Al 2 O 3 or glass polishing beads. Etch with 5% hydrofluoric acid (e.g. IPS Ceramic Etching Gel) for 20 seconds and rinse the acid off with water.
Conditioning of the restoration Allow Monobond Plus to react for 60 s and then blow dry with the air syringe. Silanization is not required for conventional cementation procedures.
Dr. R. Watzke, Liechtenstein
Dr. R. Watzke, Liechtenstein
IPS e.max CAD 3 unit bridge, R. Watzke, Liechtenstein
IPS e.max CAD 3 unit bridge, R. Watzke, Liechtenstein
IPS e.max CAD IPS 3 unit e.max bridge, CAD 3 unit R. Watzke, bridge, Liechtenstein R. Watzke, Liechtenstein
CEREC Owner Needs to do a Bridge Software version 4.2 MCLX Mill
New Blocks for CEREC
all ceramic all options
Available Now New New
Coming
New Blocks for CEREC Key Points C16 & B32 will be at Patterson shortly Owners NEED software version 4.2 to be able to design and mill anterior bridges with the B32 block Stain, Glaze, & Crystallization process is similar to a single unit Crystallize & correction fire on P1 Cementation options
IPS e.max CAD Block Pricing IPS e.max CAD Qty per Refill Whlse Retail I12 5 $104.23 $161.50 C14 5 $104.23 $161.50 C16 5 $132.99 $205.00 B32 3 $214.83 $330.50 B40 current 3 $197.04 $280.00 B40L 3 $230.75 $355.00 A14 5 $199.49 $307.00 A16 5 $232.73 $360.00