SCHÖNOX Rollat Installation instructions

SCHÖNOX Rollat Installation instructions Tanking system for wet rooms. Recommended for both solid and panel constructions, especially in wet zone 2 August 201 Replaces previous instructions of August 201 These installation instructions are part of the following series from SCHÖNOX 1 SCHÖNOX Folie Installation instructions 2 SCHÖNOX Rollat Installation instructions Tiling and grouting www.schonox.se

våtrum Branschregler för kakel och klinker i våtrum. Reglerna är framtagna av Byggkeramikrådet med hänsyn till myndighetskraven i Boverkets byggregler, BFS 2011:6 med ändringar till och med BFS 2011:26, BBR. 1 10 Five steps to an approved tanking membrane in wet rooms This installation instruction describes step by step the different actions necessary for professional installation of SCHÖNOX Rollat 1 and 2. The systems have been tested and approved to meet all applicable requirements and industry regulations. 1. Check the surface What kind of surface do the walls and floor in the wet room have? The type of tanking system used will depend on the surface and the wet zone. If there are several types of surface in the wet room, several different tanking systems may be needed. See table and drawing for Step. 2. Check applicable requirements The industry regulations for wet rooms have been produced by the industry associations BKR and Säker Vatten. They are the experts in their field and their rules must be followed to ensure approval of the construction. You can find their guidelines on our website or access them from the QR codes below. Vatten täta BBV Byggkeramikrådets branschregler för våtrum Byggkeramikrådet BBV 1:1 ersätter BBV 10:1 branschregler : SÄKER VATTENINSTALLATION 2011:1 säkervatten.se Våtzon 2 1 m Våtzon 1 Våtzon 1 Våtzon 2 1 m Hela golvet är våtzon 1. Select the tanking system SCHÖNOX Rollat 1 and 2 are two tanking systems approved by Industry Association BKR. They are also systems which can be used on all surfaces in the wet room, as they have the highest levels of reliability and watertightness. The SCHÖNOX range of approved tanking systems also includes two foil systems - SCHÖNOX Folie 1 and 2. See separate installation instruction 2

10 Wet room zones The most exposed surfaces in a wet room are classified as Wet Zone 1. This comprises the whole floor and the walls within at least one metre of the bathtub/shower. Wet Zone 2 comprises the other wall surfaces. If part of the outside wall is in wet zone 1, the whole of the wall must be treated in the same way. Other types of wet room The floors of WCs, laundry rooms and spaces containing a water heater, etc. must also be fitted with a tanking membrane. Regardless of the system chosen, the tanking membrane must continue at least 50 mm up the wall. SURFACE WET ZONE 1 WET ZONE 2 CONSTRUCTION PANELS SCHÖNOX FOLIE 1 SCHÖNOX FOLIE 2 SCHÖNOX ROLLAT 1 SCHÖNOX ROLLAT 2 SCHÖNOX FOLIE 1 SCHÖNOX FOLIE 2 SCHÖNOX ROLLAT 1 Wet room panels X X NOT PERMITTED X X X X SCHÖNOX ROLLAT 2 Paper-clad gypsum plaster panels NOT PERMITTED NOT PERMITTED X X X X Filled suspended timber flooring X X NOT PERMITTED X X NOT PERMITTED SOLID CONSTRUCTION Concrete and plaster and/or brickwork X X X X X X X X Penetrating damp SCHÖNOX 1K DS PREMIUM * * Read more in BBV Regulation 2:1. System products Quantities for the different products can be easily estimated on our website PRODUCTS COMMON TO BOTH SYSTEMS PRODUCT SEALING TAPE WetStop Sealing Tape KL WetStop Sealing Tape SH INNER AND OUTER CORNERS WetStop PC Inner Corner WetStop PC-E Outer Corner SCHÖNOX ROLLAT 1 PRODUCT SCHÖNOX KH SCHÖNOX HA SCHÖNOX ROLLAT 2 PRODUCT SCHÖNOX SPR SCHÖNOX HA CUFFS WetStop MP Pipe Cuff 10-2 mm WetStop MP Pipe Cuff 2-60 mm WetStop MP Pipe Cuff 70-125 mm WetStop MP Pipe Cuff 2 x 20-2 mm WetStop MG Gulley Cuff 70 x 70 mm WetStop MG Gulley Cuff 250 x 1500 mm TOOLS Always use suitable tools as recommended

10 1 5a. SCHÖNOX Rollat 1 6 2 For both solid and panel constructions, especially in wet zone 2 7 5 Note that SCHÖNOX Rollat 1 requires the specifier or client to carry out project design for damp proofing on all substrates/constructions. If this is not possible, one of the other SCHÖNOX tanking systems must be used. Construction elements SCHÖNOX Rollat 1 1 Substrate 2. SCHÖNOX KH. Sealing Tape KL, Inner and Outer Corners and Pipe and Gulley Cuffs. Sealing 5. SCHÖNOX HA coat 1 6. SCHÖNOX HA coat 2 7. Tile adhesive and tiles. Grouting Product summary For other products in the system, see Page of these installation instructions. SCHÖNOX KH Reduces absorption in the substrate. Mix according to instructions on the pack. Then pre-treat: Wet zone 1 solid constructions, concrete, plaster and/or brickwork. Wet zone 2 wet room panels, paper-clad gypsum plaster panels. SCHÖNOX HA Ready-to-use rubber membrane for waterproofing floors and walls prior to installing ceramic tiles. Tanking system SCHÖNOX Rollat 1 has a vapour resistance of approx. 16,000 s/m. Consumption: 1.5 kg/m². See also the instruction film on www.schonox.se 1 2 Clean the surface. Absorbent surfaces must be primed with SCHÖNOX KH. Mix according to instructions on the pack. Apply SCHÖNOX HA to the corner and mount Inner/Outer Corners. Press hard to fix. Cut suitable lengths of WetStop Sealing Tape. Brush with SCHÖNOX HA and mount Sealing Tape KL. For Sealing Tape SH: mount directly on floor/wall angle. Seal the edges with SCHÖNOX HA.

10 5 6 7 Apply SCHÖNOX HA round pipes. Mount suitably adapted Pipe Cuffs and press hard to fit. Seal the edges with SCHÖNOX HA. Position the cutting template on the JAFO floor gulley. Or follow the instructions from the gulley manufacturer. 9 10 11 12 Remove the protective paper and mount the gulley cuff. Be careful not to allow air pockets or blisters to form. Roll SCHÖNOX HA onto the walls. Total consumption for coats 1 and 2 is: 1.5 kg/m². Follow up with first coat to floor. Allow all to dry for about 2 hours. Roll more SCHÖNOX HA onto the walls. 1 1 15 16 And the floor. Check consumption. Allow to dry for at least 6 hours. Cut out the hole in the Gulley Cuff. Follow the instructions from the gulley manufacturer. JAFO: Remove the cutting template. JAFO: Fit and screw in the clamping ring. 17 1 JAFO: Fit the grate. The tiles can now be installed. NB Wait a minimum of 12 hours. 5

10 5 7 2 1 5b. SCHÖNOX Rollat 2 For both solid and panel constructions, especially in wet zone 2 9 6 With SCHÖNOX Rollat 2, SCHÖNOX SPR is used as a vapour barrier. For you as specifier/client, this means that, unlike SCHÖNOX Rollat 1, you will not need to carry out project design for damp proofing. Construction elements SCHÖNOX Rollat 2 1 Substrate 2. SCHÖNOX SPR coat 1. SCHÖNOX SPR coat 2. Sealing Tape KL, Inner and Outer Corners and Pipe and Gulley Cuffs 5. Sealing 6. SCHÖNOX HA coat 1 7. SCHÖNOX HA coat 2. Tile adhesive and tiles 9. Grouting Product summary For other products in the system, see Page of these installation instructions. SCHÖNOX SPR Vapour barrier used in conjunction with SCHÖNOX HA. This gives tanking system SCHÖNOX Rollat 2 a vapour resistance of approx. 1,100,000 s/m. The limit value specified by "Boverket" is 1,000,000 s/m. Consumption: 0.25 kg/m². SCHÖNOX HA Ready-to-use membrane for waterproofing floors, walls and whole wet rooms prior to installing ceramic tiles. Used together with SCHÖNOX SPR. Consumption: 1.0 kg/m². See also the instruction film on www.schonox.se 1 2 Clean the surface. Apply SCHÖNOX SPR. Total consumption for coats 1 and 2 is: 0.25 kg/m². Continue by rolling SCHÖNOX SPR onto the floor. Apply SCHÖNOX SPR diagonally to the wall. Check consumption. Continue by applying SCHÖNOX SPR diagonally to the floor. Allow to dry for at least 2 hours. 6

10 5 6 7 Apply SCHÖNOX HA to the corner and mount Inner/Outer Corners. Press hard to fix. Cut suitable lengths of WetStop Sealing Tape. Brush with SCHÖNOX HA and mount Sealing Tape KL. For Sealing Tape SH: mount directly on floor/wall angle. Seal the edges with SCHÖNOX HA. Apply SCHÖNOX HA round pipes. 9 10 11 12 Mount suitably adapted Pipe Cuffs and press hard to fit. Seal the edges with SCHÖNOX HA. Position the cutting template on the JAFO floor gulley. Or follow the instructions from the gulley manufacturer. Remove the protective paper and mount the gulley cuff. Be careful not to allow air pockets or blisters to form. 1 1 15 16 Roll SCHÖNOX HA onto the walls. Total consumption for coats 1 and 2 is: 1.0 kg/m². Follow up with first coat to floor. Allow all to dry for about 2 hours. Roll more SCHÖNOX HA onto the walls. Roll AquaStop on the floor. Check consumption. Allow to dry for at least 6 hours. 17 1 19 20 Cut out the hole in the Gulley Cuff. Follow the instructions from the gulley manufacturer. JAFO: Remove the cutting template. JAFO: Fit and screw in the clamping ring. JAFO: Fit the grate. The tiles can now be installed. NB Wait a minimum of 12 hours. 7

Casco Schönox is all you need Casco Schönox is part of Sika, one of the world's leading companies in the field of construction chemistry. Our research and development department is constantly creating products which make life simpler for both professional and do-ityourself users. Casco Schönox is a reliable full-line supplier of construction products. Its range includes all kinds of adhesives, levelling products, sealants and grouts. 1 Tomas Sandström sandstrom.tomas@se.sika.com +6 70-55 2 22 Härnösand/Kramfors, Sollefteå, Örnsköldsvik, Umeå, Skellefteå, Lycksele, Piteå, Luleå/Boden, Haparanda/Kalix, Kiruna/Gällivare 2 Johnny Dahl dahl.johnny@se.sika.com +6 70-512 25 77 Gävle/Sandviken, Bollnäs/Söderhamn Hudiksvall/Ljusdal, Sundsvall, Östersund Andreas Danneborn danneborn.andreas@se.sika.com +6 70-620 57 52 Karlstad, Säffle/Åmål, Arvika, Lindesberg, Borlänge/Falun, Ludvika, Mora 10 Art. no.: 227 1000 ex All products have environmental declarations and are quality-assured to meet the demands of builders, specifiers, building contractors, building managers and society as a whole. Visit schonox.se for more information about our products and for a variety of assembly instructions. For questions not answered on our website, consult your dealer. 1 Lars Holm Sales Manager/ Contracts Sweden holm.lars@se.sika.com +6 70-926 0 5 Johan Sjögren sjogren.johan@se.sika.com +6 70-55 50 05 Michael Brandt brandt.michael@se.sika.com +6 70-60 07 70 Stockholm/Södertälje, Norrtälje, Enköping, Uppsala, Fagersta, Sala, Avesta/Hedemora, Gävle/Sandviken 5 Krister Lindroth Wettermark lindroth.krister@se.sika.com +6 70-227 20 1 Nyköping, Katrineholm, Eskilstuna, Norrköping, Kristinehamn/Filipstad, Karlstad, Örebro, Karlskoga, Västerås, Köping, Fagersta, Avesta/Hedemora 2 6 Jens Nielsen nielsen.jens@se.sika.com +6 70-522 26 29 Falkenberg/Varberg, Göteborg/Alingsås, Uddevalla, Trollhättan/Vänersborg, Borås, Lidköping, Falköping, Skövde, Mariestad Bengt Carlsson carlsson.bengt@se.sika.com +6 76-11 92 00 Visby, Ängelholm, Helsingborg/Landskrona, Malmö, Halmstad, Falkenberg/Varberg, Göteborg, Uddevalla 5 7 Martin Forssmed forssmed.martin@se.sika.com +6 70-629 92 2 Linköping, Mjölby/Motala, Oskarshamn, Hultsfred/Vimmerby, Västervik, Eksjö/ Nässjö/Vetlanda, Tranås, Jönköping, Kalmar, Växjö, Ljungby, Värnamo 6 7 Greger Paulsson Wiveus paulssonwiveus.greger@se.sika.com +6 70-927 1 02 Karlskrona, Karlshamn, Kristianstad, Hässleholm, Ängelholm, Helsingborg/ Landskrona, Malmö/Lund/Trelleborg, Ystad/Simrishamn, Eslöv, Halmstad Casco Schönox Sweden AB Customer service: +6 20-7 00 E-mail address for orders: casco.order@se.sika.com Technical service: +6-621 79 00 Website: www.schonox.se