Product Catalog
Implantology Unlimited The implant system can offer solutions where other systems have reached their limits. It offers practically unlimited surgical and prosthetic freedom along with maximum safety. With you can master implantological challenges as easily as standard procedures. The narrowest gap or edentulous jaw, hard or soft bone, singlesession or two-session, immediate loading or delayed loading with the comprehensive range of implants from 3.0 mm up to 5.5 mm diameter and 8 mm up to 18 mm length, the bone-specific preparation protocol and wide range of prosthetic options available with the system, which is appreciated by dental technicians all over the world, helps you achieve an outstanding safe and predictable result in every case. CONTENT PLANNING Planning Components 4 SURGERY Implant Package 6 Implants 7 Surgical Kit 10 FRIOS Surgical Set, Contra-angle Handpieces 13 Surgical Instruments 14 Guided Surgery with ExpertEase 23 S Prosthetic Components 26 S Prosthetic Components Esthetic Fabrication of superstructure at implant level 28 S Prosthetic Components Multi-Purpose Fabrication of superstructure at gingiva level 42 TG Prosthetic Components 49 Prosthetic Instruments 55 PRESENTATION MATERIAL 58 MATERIALS 59 Labelling of materials Information regarding the materials involved in implants, system components and instruments is given in the form of a reference number after every article: FRIADENT Gingiva Former 2. Page 59 of this catalog presents an overview of the materials and the composition of the materials used. The images in this catalog are for illustration purposes only. The size of the illustrated products may deviate from the original product. DENTSPLY Friadent reserves the right to make any technical changes without prior notice. PRESENTATION MATERIAL SURGERY PLANNING
Planning Components FRIADENT Select Others PLANNING FRIADENT Select Try-in Abutment Determination of oro-vestibular and mesio-distal implant position and of the distance to the adjacent teeth Determination of gingival height, angulation and position of the horizontal screw (GH 2) for all FRIADENT abutments FRIADENT Select Sleeve Exact transfer of the pre-prosthetic planning to the clinical situation FRIADENT Select Try-in Implants Intra-operative check of implant position, implant axis, congruency between implant and bone crest and peri-implant soft tissue level FRIADENT Select Try-in Abutment 2 45 2119 D 3.0 / A 0 (straight) 45 2120 D 3.4 / A 0 (straight) 45 2121 D 3.8 / A 0 (straight) 45 2122 D 4.5 / A 0 (straight) 45 2123 D 5.5 / A 0 (straight) 45 2219 D 3.0 / A 15 (angled 15 ) 45 2220 D 3.4 / A 15 (angled 15 ) 45 2221 D 3.8 / A 15 (angled 15 ) 45 5025 D 3.0 45 5035 D 3.4 45 5045 D 3.8 45 5055 D 4.5 45 5065 D 5.5 FRIADENT Select Sleeve 2 without pin 91 4502 Pin for FRIADENT Select Sleeve 2 26 1500 Select Basic Set Try-in Implant One Select Try-in Implant per Implant diameter (D 3.0 D 5.5) 26 1520 D 3.0 26 1530 D 3.4 26 1540 D 3.8 26 1550 D 4.5 26 1560 D 5.5 Select Try-in Implant 2 49 1211 FRIADENT Radiographic Balls for Pre-surgical Planning 6 Ø 5 mm, 12 pieces Radiographic Template 26 9020 S (subgingival) 25 5206 TG (transgingival) Guided Surgery with ExpertEase Digital treatment planning based on three-dimensional imaging procedures enables the therapy to be planned with absolute accuracy and makes the result of the treatment exactly predictable. ExpertEase from DENTSPLY Friadent offers a complete solution for digital treatment planning and template-guided implant placement based on the Simplant program from Materialise, which is used all over the world. ExpertEase System Components: ExpertEase Software ExpertEase Drill Guides ExpertEase Instruments For information on the ExpertEase Software Kit and patient-specific drill guides please see: 26 1510 Depth Gauge 2 D 2.0 Smartphone: For instruments for Guided Surgery with ExpertEase please see pages 12 and 23 25 of this catalog. 4 5
Implant Package Implants S Implants implants are supplied in a double-sterile blister package with an outer carton. The type of package offers the maximum product safety in conformance with the increasingly rigid requirements for medical devices. The packaging also makes it easy to store all products for quick retrieval and they are easy to handle during the surgical procedure. All other DENTSPLY Friadent products for surgery and prosthetics are also sealed in blisters in branded cardboard packages. Outer box package Simple product classification with brandspecific design, sight window and color-coded imprint of the implant diameter Large seal label with details of products Stackable, all important product information remains visible Includes multilingual instructions for use Transparent outer blister Outer sterile barrier of implant package Transparent inner blister Inner sterile package Contains implant shuttle with implant and cover screw for implants Peel-off label with batch code for reliable documentation of treatment S plus Screw Implant (sterile) Content: Screw Implant 2, TempBase 4, Cover Screw 2 26 2422 D 3.0 / L 11 26 2423 D 3.0 / L 13 26 2425 D 3.0 / L 15 26 2431 D 3.4 / L 9.5 26 2432 D 3.4 / L 11 26 2433 D 3.4 / L 13 26 2435 D 3.4 / L 15 26 2438 D 3.4 / L 18 26 2440 D 3.8 / L 8 26 2441 D 3.8 / L 9.5 26 2442 D 3.8 / L 11 26 2443 D 3.8 / L 13 26 2445 D 3.8 / L 15 26 2448 D 3.8 / L 18 26 2450 D 4.5 / L 8 26 2451 D 4.5 / L 9.5 26 2452 D 4.5 / L 11 26 2453 D 4.5 / L 13 26 2455 D 4.5 / L 15 26 2458 D 4.5 / L 18 26 2460 D 5.5 / L 8 26 2461 D 5.5 / L 9.5 26 2462 D 5.5 / L 11 26 2463 D 5.5 / L 13 26 2465 D 5.5 / L 15 Indications Single-tooth replacement Fixing bridges and prostheses D 3.0: single tooth crowns in the front-tooth region and splinted singletooth restorations Healing mode Submerged or transgingival with gingival-forming components or temporary dentures Insertion of implants: Implant Driver (page 21) Loosening of TempBase Retaining Screw, Placement of Implant Cover Screw: Hex Driver 0.9 mm (page 21) SURGERY Plastic implant shuttle Holds the implant securely in the packaging and protects it from damage during transport and removal Makes non-contact transfer and acceptance of the implant easy during the operation Three wings with roughened surfaces for non-slip holding make it very easy to handle safely Inner blister (sterile) Implant shuttle with Implant Implant Cover Screw FRIADENT TempBase (pre-mounted) Implant Implant shuttle Implant packaging All implants are delivered in double-sterile packaging (see page 6). 6 7
Implants FRIADENT TempBase TG Implants FRIADENT TempBase Implant holder and placement head FRIADENT TempBase with TempBase Cap Transfer coping for index registration during surgery Basis for temporary restorations The FRIADENT TempBase is included with the implants. The FRIADENT TempBase Cap must be ordered separately. Fixation and loosening of TempBase Retaining Screw, Placement of Implant Cover Screw: Hex Driver 0.9 mm (page 21) 46 1220 D 3.0 4 46 1230 D 3.4 4 46 1240 D 3.8 4 46 1250 D 4.5 4 46 1260 D 5.5 4 FRIADENT TempBase 4 with TempBase Retaining Screw FRIADENT TempBase Cap 28 46 1235 D 3.0 D 3.8 46 1255 D 4.5 46 1265 D 5.5 FRIADENT TempBase Retaining Screw 4 46 1279 D 3.0 46 1280 D 3.4 D 5.5 TG plus Transgingival Screw Implant (sterile) Screw Implant 3, Placement Head 25 2431 D 3.4 / L 9.5 25 2432 D 3.4 / L 11 25 2433 D 3.4 / L 13 25 2435 D 3.4 / L 15 25 2440 D 3.8 / L 8 25 2441 D 3.8 / L 9.5 25 2442 D 3.8 / L 11 25 2443 D 3.8 / L 13 25 2445 D 3.8 / L 15 25 2450 D 4.5 / L 8 25 2451 D 4.5 / L 9.5 25 2452 D 4.5 / L 11 25 2453 D 4.5 / L 13 25 2455 D 4.5 / L 15 Indications Single-tooth replacement Fixing bridges and prostheses Healing mode Transgingival with TG Implant Cover Screw or non-functional/functional immediate loading Insertion of implants: TG Implant Driver (page 21) Loosening of Adapter Screw, Placement of Implant Cover Screw: Hex Driver 0.9 mm (page 21) SURGERY 25 9200 TG Clinical Set Cover Screw (Four Cover Screws) FRIADENT Implant Cover Screw 2 25 1400 TG Implant Cover Screw 2 45 1120 D 3.0 45 1130 D 3.4 45 1140 D 3.8 45 1150 D 4.5 45 1160 D 5.5 8 9
Surgical Kit New customized surgical kits Simple, flexible and economical with the modular design with absolute minimum number of instruments required. Can be customized with additional modules as required. Instruments securely fixed in silicone holders. Clear and simple user guidance during surgery. Integrated organizer for used instruments. Can be easily and thoroughly cleaned. Organizer Tray Cover Tool Module Round Drill D 3.0 */** 26 1110 Ratchet Insert for Instruments */** 26 6120 and 2 open slots Ratchet */** 45 6020 Implant Driver D 3.0 / S */** 26 6030 Implant Driver for Implant and TempBase D 3.4 / S */** 26 6040 Implant Driver D 3.8 D 5.5 / S ** 26 6050 Implant Driver D 3.0 / L * 26 6035 Implant Driver for Implant and TempBase D 3.4 / L * 26 6045 Implant Driver D 3.8 D 5.5 / L 26 6055 Twist Drill D 2.0 / S */** 26 1115 Twist Drill D 2.0 / L * 26 1118 3 FRIADENT Paralleling Pins D 2.0 / D 3.0 */** 45 5106 3 open slots Extension Instrument */** 26 6130 TG Implant Driver 25 6010 ** and 2 open slots Hex Driver 0.9 mm / S 26 6190 */** Hex Driver 0.9 mm / L 26 6195 * FRIADENT Select Try-in Abutment D 3.0 / A 0 (straight) 45 2119 * D 3.4 / A 0 (straight) 45 2120 D 3.8 / A 0 (straight) 45 2121 D 4.5 / A 0 (straight) 45 2122 D 5.5 / A 0 (straight) 45 2123 Twist Drill D 3.0 / S 26 1125 */** D 3.4 / S 26 1135 ** D 3.8 / S 26 1145 ** D 4.5 / S 26 1155 D 5.5 / S 26 1165 Twist Drill D 3.0 / L 26 1128* D 3.4 / L 26 1138 D 3.8 / L 26 1148 D 4.5 / L 26 1158 D 5.5 / L 26 1168 Twist Drill Crestal D 3.0 26 1120 */** D 3.4 26 1130 ** D 3.8 26 1140 ** D 4.5 26 1150 D 5.5 26 1160 Tap D 3.0 26 1122 */** D 3.4 26 1132 ** D 3.8 26 1142 ** D 4.5 26 1152 D 5.5 26 1162 Select Try-in Implant D 3.0 26 1520 * D 3.4 26 1530 D 3.8 26 1540 D 4.5 26 1550 D 5.5 26 1560 SURGERY Drill Modules * Included in Surgical Kit D 3.0 / S + L ** Included in Surgical Kit D 3.0 D 3.8 / S All instruments are included in the Surgical Kit D 3.0 D 5.5 / S + L Tray Base Plate Scope of Supply Drill Tool Module XIVE Surgical Kits Module D 3.0 Drill Module D 3.4 & D 3.8 Drill Module D 4.5 & D 5.5 D 3.0 D 5.5/S + L Drill Module individual (empty) Module Tray Insert D 3.0 D 3.8/S 10 11 D 3.0/S + L
Surgical Kits SurgicalSet, Contra-angle Handpieces Surgical Kits FRIOS Surgical Set 26 7000 Surgical Kit D 3.0 D 5.5 / S+L D 3.0 D 5.5 All instruments required for the placement of implants D 3.0 D 5.5, length of instruments S (short) and L (long) 90 6600 FRIOS Unit S/i V 220 240 AC Scope of delivery: FRIOS Unit S/i with handmotor (cable length 1.8 m), tray for motor, stand, foot control, mains cable, hose set, hose rings (5 pieces), locking pin for motor FRIOS Unit S/i Simple operating concept specially designed for implant surgery Powerful, quiet running surgical motor User-oriented program sequence with thread-tapping function actuated by pushbutton 26 7005 Surgical Kit D 3.0 D 3.8 / S D 3.0 D 3.8 All instruments required for the placement of implants D 3.0 D 3.8, length of instruments S (short) 26 7003 Surgical Kit D 3.0 / S+L D 3.0 All instruments required for the placement of D 3.0 implants, length of instruments S (short) and L (long) SURGERY 26 5000 Surgical Kit GS (Guided Surgery) D 3.0 D 4.5 All instruments required for computer-aided placement of implants D 3.0 D 4.5 of lengths L 8 L 15 Surgical Kit Modules and Equipment 26 7025 D 3.0 26 7035 D 3.4 26 7045 D 3.8 26 7055 D 4.5 26 7065 D 5.5 Drill Module (empty) 26 7200 Tool Module (empty) 26 7170 Module Tray Insert 26 7010 Surgical Kit Tray (empty) FRIOS Hand and Contra-angle Pieces 90 6720 FRIOS Contra-angle Handpiece WS-75 20:1, demountable 90 6710 FRIOS Contra-angle Handpiece WI-75 20:1 90 6810 FRIOS Contra-angle Handpiece WI-75 LED G 90 5030 FRIOS Handpiece straight 1:1 90 5050 FRIOS Handpiece angled 1:1 90 6850 FRIOS Handpiece SI-11 LED G 1:1 FRIOS Contra-angle Handpieces Patented hexagonal clamping system for trouble-free surgical procedures and less wear on instruments Demountable version with head that rotates 90 for access to difficult regions, also meets the most rigid hygiene requirements LED version with neutral white LED light and higher luminous intensity and larger field of illumination than conventional halogen lamps A comprehensive overview of accessories available for the FRIOS Unit S/i, together with all FRIOS hand- and contra-angle pieces, as well as the products of our FRIOS product range for augmentation, are given in our product catalog FRIOS, order no. 6-302017. Smartphone: 26 5010 Surgical Kit Tray GS (empty) 12 13
Surgical Instruments The drill sequence A successful implant placement requires precise and careful implant site preparation. Therefore, please follow our recommendations for drilling exactly. Pilot hole: D 2.0 Twist Drill Twist Drills and Twist Drills crestal are used at 800 rpm. During the preparation make sure drills are adequately internally and externally irrigated. Optimum flow volume is guaranteed if separate sources are used for internal and external irrigation. Marking: Round Drill Preparation of the implant site: Twist Drill Starting with D 3.0 and increasing in diameter until the final implant diameter is reached. 1 2 Crestal preparation to achieve the internal condensation effect: Twist Drill crestal The crestal drilling varies between 2 and 6 mm based on the bone quality. Thus, an optimal primary stability of the implant in all types of bone is achieved. 3 4 If required, pre-tapping the implant thread: In very cortical bone, pre-tapping of the implant site at 15 rpm is required in the crestal area after the initial 6 mm deep preparation. The Tap can be used to reduce the crestal torque achieved during insertion of implants. S all Implants D 3.0 S and TG all Implants D 3.4 Twist Drill S or L D 2.0 Round Drill Twist Drill S or L D 3.0 Twist Drill S or L D 3.4 Twist Drill crestal D 3.0 Twist Drill crestal D 3.4 Tap D 3.0 Tap D 3.4 2 mm SURGERY S and TG all Implants D 3.8 Twist Drill S or L D 3.8 Twist Drill crestal D 3.8 Tap D 3.8 1 2 3 4 Twist Drill S Twist Drill L S and TG all Implants D 4.5 S all Implants D 5.5 Twist Drill S or L D 4.5 Twist Drill S or L D 5.5 Twist Drill crestal D 4.5 Twist Drill crestal D 5.5 Tap D 4.5 Tap D 5.5 18 mm 15 mm 13 mm 11 mm 9.5 mm 8 mm S L 13 TG L 13 0.5 mm Option: BoneCondenser In cases of poor bone quality, BoneCondensers can be used for lateral and apical implant site condensation. This improvement of bone quality and quantity enhances primary implant stabilization. 14 15
Surgical Instruments Single-patient Drills Sets Drills for multiple use Single-patient Drills Twist drills for implant site preparation up to the planned implant diameter in one patient Continuing procedure: The crestal twist drill (page 17) must be used in addition after reaching the required diameter. In cortical bone (D I) the tap (page 17) must also be used. The instruments for insertion and restoration of the implants are shown on page 21. Single-patient Drill 6 Set (sterile) All twist drills required for implant site preparation of the respective implant diameter. 26 3025 D 3.0 / L 8 L 15 26 3035 D 3.4 / L 8 L 15 26 3045 D 3.8 / L 8 L 15 26 1110 Round Drill 6 Twist Drill S 6 (short) for implant lengths 8 15 mm 26 1115 D 2.0 / L 8 15 26 1125 D 3.0 / L 8 15 26 1135 D 3.4 / L 8 15 26 1145 D 3.8 / L 8 15 26 1155 D 4.5 / L 8 15 26 1165 D 5.5 / L 8 15 Twist Drill L 6 (long) for implant lengths 8 18 mm 26 1118 D 2.0 / L 8 18 26 1128 D 3.0 / L 8 18 26 1138 D 3.4 / L 8 18 26 1148 D 3.8 / L 8 18 26 1158 D 4.5 / L 8 18 26 1168 D 5.5 / L 8 18 Twist Drill S and L For implant site preparation up to the planned implant diameter With internal irrigation Adaptation of the twist drills to the planned implant length with depth stops (page 18) The Twist Drills S and L are provided with color-coded marking rings for clear distinction. S 1 ring L 2 rings SURGERY 26 3055 D 4.5 / L 8 L 15 26 1120 D 3.0 26 1130 D 3.4 26 1140 D 3.8 26 1150 D 4.5 26 1160 D 5.5 Twist Drill crestal 6 Twist Drill crestal For crestal implant site preparation according to the bone quality once the planned implant diameter has been reached The Twist Drill crestal always has to be used 26 3065 D 5.5 / L 8 L 15 Single-patient Drills Single articles Tap 6 26 1122 D 3.0 26 1132 D 3.4 26 1142 D 3.8 26 1152 D 4.5 26 1162 D 5.5 Tap For pre-tapping of the implant threads in cortical bone (D I) Please note: Cutting instruments should generally be replaced after 20 cycles of use. Blunt or damaged instruments must be replaced immediately. Single-patient Drill 6 (sterile) 26 1015 D 2.0 / L 8 L 15 Continuing procedure: The instruments for insertion and restoration of the implants are shown on page 21. 26 1025 D 3.0 / L 8 L 15 26 1035 D 3.4 / L 8 L 15 26 1045 D 3.8 / L 8 L 15 26 1055 D 4.5 / L 8 L 15 16 26 1065 D 5.5 / L 8 L 15 17
Surgical Instruments XIVE Depth Stops for Twist Drills Sets Other Instruments for Implant Site Preparation Depth Stops Safe implant site preparation by adaptation of the universal twist drills (multiple use) to the planned implant diameter The Depth Stops S and L are provided with color-coded marking rings for clear distinction. 26 1200 Expert Security Kit / S+L All depth stops required for using the universal twist drills, lengths S (short) and L (long). 26 1205 Standard Security Kit / S All depth stops required for using the universal twist drills, length S (short). Trephine Drill 6 26 1129 D 3.0 / L 8 L 18 26 1139 D 3.4 / L 8 L 18 26 1149 D 3.8 / L 8 L 18 26 1159 D 4.5 / L 8 L 18 26 1169 D 5.5 / L 8 L 18 FRIADENT Paralleling Pin 2 45 5106 D 2.0/D 3.0 Please note the instructions for use! S 1 ring L 2 rings XIVE Depth Stops for Twist Drills Single articles Depth Stop S 6 (short) 45 5280 FRIADENT Drill Cleaning Instrument 6 91 0003 FRIADENT Drill Extension 6 90 5047 FRIOS Contra-angle Handpiece 20:1 Irrigation Tube The drill extension must always be used with the long internal irrigation tube. SURGERY 26 1210 D 2.0 D 3.0 / L 8 26 1211 D 2.0 D 3.0 / L 9.5 26 1212 D 2.0 D 3.0 / L 11 26 1213 D 2.0 D 3.0 / L 13 26 1215 D 2.0 D 3.0 / L 15 90 5043 Long Internal Irrigation Tube 6 (for Drill Extension) 26 1230 D 3.4 D 3.8 / L 8 26 1231 D 3.4 D 3.8 / L 9.5 26 1232 D 3.4 D 3.8 / L 11 26 1233 D 3.4 D 3.8 / L 13 26 1235 D 3.4 D 3.8 / L 15 26 1250 D 4.5 D 5.5 / L 8 26 1251 D 4.5 D 5.5 / L 9.5 26 1252 D 4.5 D 5.5 / L 11 26 1253 D 4.5 D 5.5 / L 13 26 1255 D 4.5 D 5.5 / L 15 Depth Stop L 6 (long) No instruments are required for placing and removing the depth stops. 26 1310 D 2.0 D 3.0 / L 8 26 1311 D 2.0 D 3.0 / L 9.5 26 1312 D 2.0 D 3.0 / L 11 26 1313 D 2.0 D 3.0 / L 13 26 1315 D 2.0 D 3.0 / L 15 26 1318 D 2.0 D 3.0 / L 18 26 1330 D 3.4 D 3.8 / L 8 26 1331 D 3.4 D 3.8 / L 9.5 26 1332 D 3.4 D 3.8 / L 11 26 1333 D 3.4 D 3.8 / L 13 26 1335 D 3.4 D 3.8 / L 15 26 1338 D 3.4 D 3.8 / L 18 26 1350 D 4.5 D 5.5 / L 8 26 1351 D 4.5 D 5.5 / L 9.5 26 1352 D 4.5 D 5.5 / L 11 26 1353 D 4.5 D 5.5 / L 13 26 1355 D 4.5 D 5.5 / L 15 26 1358 D 4.5 D 5.5 / L 18 26 1390 Security Kit Tray (empty) 18 19
Surgical Instruments BoneCondenser Sets Instruments for Implant Placement BoneCondenser For lateral and apical bone condensing in reduced bone quality For improving bone quality and quantity with increased primary stability of implants Universal length with depth marks at the working tips BoneCondenser, angled When limited space is available and for the posterior region 26 1600 Instrument-Set BoneCondenser straight and angled Tray with all BoneCondensers, straight and angled 26 1603 Instrument-Set BoneCondenser straight Tray with all BoneCondensers, straight 26 1606 Instrument-Set BoneCondenser angled Tray with all BoneCondensers, angled BoneCondenser Single articles Implant Driver S 6 (short) 26 6030 for S implants D 3.0 26 6040 for S implants D 3.4 and TempBase 26 6050 for S implants D 3.8 D 5.5 Implant Driver L 6 (long) 26 6035 for S Implants D 3.0 26 6045 for S Implants D 3.4 and TempBase Implant Drivers and Hex Drivers XiVE Implant Drivers and Hex Drivers All instruments can be used either with the contra-angle handpiece or the ratchet For placing S implants with the TempBase (standard procedure), only the Implant Driver for XiVE S Implants D 3.4 and TempBase is needed, regardless of the implant diameter. The implant drivers of other diameters are applied only when placing the implants using the implant internal geometry. SURGERY 26 6055 for S Implants D 3.8 D 5.5 26 1610 D 2.0 26 1620 D 3.0 26 1630 D 3.4 26 1640 D 3.8 26 1650 D 4.5 26 1660 D 5.5 BoneCondenser, straight 25/6 TG Implant Driver 6 25 6010 for TG Implants Hex Driver 6 26 6190 0.9 mm/s (short) 26 6195 0.9 mm/l (long) 26 1615 D 2.0 26 1625 D 3.0 26 1635 D 3.4 26 1645 D 3.8 26 1655 D 4.5 26 1665 D 5.5 BoneCondenser, angled 25/6 new 45 6020 Ratchet 6 26 6120 Ratchet Insert for Instruments 6 26 6130 Extension Instrument 6 46 5880 FRIADENT Implant Driver Manual long 6 45 6010 Surgical Ratchet with Torque Indicator 6 Ratchet Insert for Instruments For fixing the instruments with ISOshaft to the ratchet. These instruments can be used either with the contra-angle handpiece or the ratchet. Surgical ratchet with torque indicator Increased safety for manual screwing of implants Readable torque indicator Adjustable clockwise and counterclockwise rotation 20 21
Surgical Instruments Surgical Instruments GUIDED SURGERY WITH EXPERTEASE Instruments for Uncovery Drills for Guided Surgery 45 5665 D 3.0 45 5666 D 3.4 45 5660 D 3.8 45 5661 D 4.5 45 5662 D 5.5 FRIADENT Tissue Punch 6 45 5550 FRIADENT Soft Tissue Gauge 4 26 5201 D 3.0 GS 26 5301 D 3.4 GS 26 5401 D 3.8 GS 26 5501 D 4.5 GS Soft Tissue Punch 6 GS Initial Drill 6 GS 26 5202 D 3.0 GS 26 5302 D 3.4 GS 26 5402 D 3.8 GS 26 5502 D 4.5 GS Twist Drill 6 GS 26 5108 D 2.0 / L 8 GS 26 5208 D 3.0 / L 8 GS 26 5308 D 3.4 / L 8 GS 26 5408 D 3.8 / L 8 GS 26 5508 D 4.5 / L 8 GS Soft Tissue Punch GS For the minimally-invasive exposure of the surgical site Initial Drill GS (Guided Surgery) For removal of soft-tissue residue after use of the mucosa punch For smoothing the planned implant position (specific to the implant diameter) Twist Drill GS Drills in implant length for implant site preparation up to the planned implant diameter The drills are guided in the surgical template by the sleeve for twist drills (sleeve-on-drill system) SURGERY 26 5195 D 2.0 / L 9.5 GS 26 5295 D 3.0 / L 9.5 GS 26 5395 D 3.4 / L 9.5 GS 26 5495 D 3.8 / L 9.5 GS 26 5595 D 4.5 / L 9.5 GS 26 5111 D 2.0 / L 11 GS 26 5211 D 3.0 / L 11 GS 26 5311 D 3.4 / L 11 GS 26 5411 D 3.8 / L 11 GS 26 5511 D 4.5 / L 11 GS 26 5113 D 2.0 / L 13 GS 26 5213 D 3.0 / L 13 GS 26 5313 D 3.4 / L 13 GS 26 5413 D 3.8 / L 13 GS 26 5513 D 4.5 / L 13 GS Please note: Cutting instruments should generally be replaced after 20 cycles of use. Blunt or damaged instruments must be replaced immediately. Please note: Instruments named GS are only for use with ExpertEase Guided Surgery procedures. 26 5115 D 2.0 / L 15 GS 26 5215 D 3.0 / L 15 GS 26 5315 D 3.4 / L 15 GS 26 5415 D 3.8 / L 15 GS 26 5515 D 4.5 / L 15 GS 22 23
Surgical Instruments GUIDED SURGERY WITH EXPERTEASE Sleeves for Guided Surgery Implant Drivers for Guided Surgery Sleeves for Twist Drills For safe guidance of the drills in the surgical template (sleeve-on-drill system) No instruments are required for mounting the sleeves to the drills and implant drivers. 26 5105 D 2.0 26 5205 D 3.0 26 5305 D 3.4 26 5405 D 3.8 Narrow sleeve for twist drill 6 GS Narrow Sleeve for Twist Drill 6 GS Set 26 5605 D 2.0 D 3.8 26 5103 D 2.0 26 5203 D 3.0 26 5303 D 3.4 26 5403 D 3.8 26 5503 D 4.5 Wide Sleeve for Twist Drill 6 GS 26 5700 short, narrow 26 5701 short, wide 26 5702 long, narrow 26 5703 long, wide Implant Driver G S 6 for TempBase 26 5704 Wide Sleeve for Implant Driver 6 GS 26 5705 Narrow Sleeve for Implant Driver 6 GS Implant Driver GS Available in two lengths as well as narrow and wide diameters for screwing in S implants D 3.0 D 4.5 via the TempBase Sleeves can be ordered separately as spare parts Please see page 21 for more instruments for the insertion and restoration of implants SURGERY Wide Sleeve for Twist Drill 6 GS Set 26 5603 D 2.0 D 4.5 Stabilization Abutments Twist Drill crestal GS For crestal implant site preparation according to the bone quality once the planned implant diameter has been reached The Twist Drill crestal always has to be used 26 5020 D 3.0 GS 26 5030 D 3.4 GS 26 5040 D 3.8 GS 26 5050 D 4.5 GS Twist Drill crestal 6 GS 26 5850 narrow 26 5852 wide Stabilization AbutmentS 6 GS for TempBase Stabilization abutment GS for TempBase For securing the drill guide against lateral movement and twisting when preparing several implant sites. Tap GS For pre-tapping of the implant threads in cortical bone (D I) Tap 6 GS 26 5022 D 3.0 GS 26 5032 D 3.4 GS 26 5042 D 3.8 GS 26 5052 D 4.5 GS 24 25
Prosthetic Components The type of prosthetic restoration is selected according to the indication after the implants have healed or when they are uncovered. A wide range of prefabricated components is available in the FRIADENT prosthetics range in implant diameters, various gingival heights, straight and angled. There are two basic procedures: The Esthetic procedure with fabrication of the superstructure at implant level The Multi-Purpose procedure with fabrication of the superstructure using the MP Abutment at gingiva level Esthetic procedure For reconstructions in which the esthetic aspect is in the foreground For cemented-in and screw-retained single-tooth restorations and bridges and overdentures fixed to attachments For prosthetic restoration of D 3.0 implants (single-tooth crowns only) For fabrication of porcelain restorations (not available for all implant diameters) For difficult initial prosthetic situations that require customized solutions Multi-Purpose (MP) procedure For cases in which a simple and standardized procedure has priority and the function of the restoration is the primary concern For screw-retained bridge constructions and removable implantborne prostheses The dentist selects and positions the prosthetic abutment at chairside before taking the impression. The impression is made at gingiva level above the prosthetic abutment. The abutment then remains in the patient's mouth. Please note: the Multi-Purpose procedure cannot be used to fabricate single-tooth crowns and implant-borne restorations on D 3.0. Cemented-in restorations are also not possible because of the restricted abutment height. The impression is made at implant level, the laboratory selects the prosthetic abutment. Healing Soft tissue management Impressions Prosthetic restoration SUBMERGED Index registration TempBase Page 8 FRIADENT Cover Screw for Implants Page 8 FRIADENT Cover Screw Page 8 Labside temporary with FRIADENT TempBase Page 8 FRIADENT Gingiva Former Page 28 Temporary with FRIADENT EsthetiCap Page 29 CROWNS AND BRIDGES FRIADENT EstheticBase Page 34 FRIADENT CERCON * Page 36 FRIADENT CeraBase* Page 36 Custom Abutment ZiO2 by Compartis Page 39 TitaniumBase Page 38 Healing Soft tissue management Impressions Prosthetic restoration SUBMERGED Index registration TempBase Page 8 FRIADENT Cover Screw for Implants Page 8 TRANSGINGIVAL FRIADENT MP Abutment Page 42 FRIADENT Cover Screw Page 8 Chairside temporary with FRIADENT TempBase Page 8 MP Cover Screw Page 42 Labside temporary with FRIADENT TempBase Page 8 FRIADENT MP Abutment Page 42 MP Cover Screw Page 42 Labside temporary with FRIADENT TempBase Page 8 FRIADENT MP Abutment Page 42 FRIADENT MP Abutment Page 42 MP Impression Coping Page 43 BRIDGES Bridges on FRIADENT Castable/Cast-to Waxing Sleeve Page 44 FRIADENT PassivFit Page 44 OVERDENTURES Bar constructions on FRIADENT Bar Coping Page 46 FRIADENT AuroBase Page 37 FRIADENT Telescopic Abutment Page 37 *Only anterior single-tooth replacement FRIADENT Transfer Coping Page 31 OVERDENTURES FRIADENT Attachment Page 40 TRANSGINGIVAL Chairside temporary with FRIADENT TempBase Page 8 FRIADENT Gingiva Former Page 28 An individually fabricated temporary on a FRIADENT EsthetiCap or a FRIADENT ProTect abutment can be placed. FRIADENT AuroBase Page 37 FRIADENT Telescopic Abutment Page 37 LOCATOR Locator Abutment Page 41 26 27
Soft Tissue Management, Temporary Restorations Prosthetic Components Esthetic FABRICATION OF THE SUPERSTRUCTURE ON IMPLANT LEVEL Gingiva Formers Gingiva Formers FRIADENT Gingiva Former For simple contouring of the peri-implant soft tissue Selection according to implant diameter (D) and gingival height (GH) 1 mm 2 mm 3 mm 5 mm GH 1 GH 2 GH 3 GH 5 Placement of the Gingiva Former: FRIADENT Hex Driver 0.9 mm or FRIADENT Slot Screwdriver 2.0 mm (page 56) FRIADENT Gingiva Former Slim For perfect contouring of the soft tissue with limited mesio-distal space The Transfer Coping Slim is used to make impressions (page 31) FRIADENT Gingiva Former 2 45 1421 D 3.0 / GH 1 45 1422 D 3.0 / GH 2 45 1423 D 3.0 / GH 3 45 1425 D 3.0 / GH 5 45 1431 D 3.4 / GH 1 45 1432 D 3.4 / GH 2 45 1433 D 3.4 / GH 3 45 1435 D 3.4 / GH 5 45 1441 D 3.8 / GH 1 45 1442 D 3.8 / GH 2 45 1443 D 3.8 / GH 3 45 1445 D 3.8 / GH 5 45 1451 D 4.5 / GH 1 45 1452 D 4.5 / GH 2 45 1453 D 4.5 / GH 3 45 1455 D 4.5 / GH 5 45 1461 D 5.5 / GH 1 45 1462 D 5.5 / GH 2 45 1463 D 5.5 / GH 3 45 1465 D 5.5 / GH 5 FRIADENT Gingiva Former 2 Slim 45 1232 D 3.4 / GH 2 45 1233 D 3.4 / GH 3 45 1235 D 3.4 / GH 5 45 1242 D 3.8 / GH 2 45 1243 D 3.8 / GH 3 45 1245 D 3.8 / GH 5 Temporary Restorations FRIADENT Gingiva Former 2 Loop 45 1333 D 3.4 / GH 3 45 1335 D 3.4 / GH 5 45 1343 D 3.8 / GH 3 45 1345 D 3.8 / GH 5 45 1353 D 4.5 / GH 3 45 1355 D 4.5 / GH 5 45 1363 D 5.5 / GH 3 45 1365 D 5.5 / GH 5 FRIADENT EsthetiCap 24/32 with Screw for EsthetiCap 46 1730 D 3.4 / oval 46 1740 D 3.8 / oval 46 1745 D 3.8 / triangular 46 1750 D 4.5 / oval 46 1755 D 4.5 / triangular 46 1760 D 5.5 / oval 46 1765 D 5.5 / triangular FRIADENT Gingiva Former Loop For easy securing of suture material, thus enabling simple and safe soft tissue surgery FRIADENT EsthetiCap For esthetically demanding temporary crowns and bridges Two anatomical cross-sections oval and triangular Customizable by grinding or laminating Cementable X-ray-opaque with zirconium oxide additives Screwing in of EsthetiCap screw: FRIADENT Hex Driver 0.9 mm (page 56) 45 1252 D 4.5 / GH 2 45 1253 D 4.5 / GH 3 45 1255 D 4.5 / GH 5 28 29
Prosthetic Components Esthetic FABRICATION OF THE SUPERSTRUCTURE ON IMPLANT LEVEL Impressions Impressions Sets Impressions Single Components FRIADENT Transfer Coping For transferring the implant position to the master model Available for PickUp (open tray) and transfer technique The Transfer Coping GH 3 is used for gingiva up to 3 mm thick. Please use the Transfer Coping GH 5 for gingiva exceeding 3 mm thickness. 46 8223 D 3.0 / GH 3 46 8225 D 3.0 / GH 5 46 8233 D 3.4 / GH 3 46 8235 D 3.4 / GH 5 FRIADENT Lab Set PickUp Impression Content: Transfer Coping, PickUp Guide Pin (D 3.0 with PickUp Guide Pin D 3.0), FRIADENT TransferCap and Implant Analog. FRIADENT Transfer Coping (PickUp Technique) with PickUp Guide Pin (D 3.0 with PickUp Guide Pin D 3.0) and FRIADENT TransferCap 45 1625 D 3.0 / GH 3 4 45 1622 D 3.0 / GH 5 4 45 1635 D 3.4 / GH 3 2 45 1632 D 3.4 / GH 5 2 Screwing in of PickUp screw as well as abutment screw Standard and D 3.0: FRIADENT Hex screwdriver 1.22 mm or FRIADENT Slot Screwdriver 2.0 mm (D 3.4 D 5.5) (page 56) 3 mm 5 mm GH 3 GH 5 46 8243 D 3.8 / GH 3 46 8245 D 3.8 / GH 5 46 8253 D 4.5 / GH 3 46 8255 D 4.5 / GH 5 45 1645 D 3.8 / GH 3 2 45 1642 D 3.8 / GH 5 2 45 1655 D 4.5 / GH 3 2 45 1652 D 4.5 / GH 5 2 The head of the transfer copings is flattened on three sides. 46 8263 D 5.5 / GH 3 46 8265 D 5.5 / GH 5 45 1665 D 5.5 / GH 3 2 45 1662 D 5.5 / GH 5 2 FRIADENT Lab Set Transfer Impression Content: Transfer Coping, Standard Abutment Screw (D 3.0 with Standard Abutment Screw D 3.0), FRIADENT TransferCap and Implant Analog FRIADENT Transfer Coping (Transfer Technique) with Standard Abutment Screw (D 3.0 with Standard Abutment Screw D 3.0) and FRIADENT TransferCap 46 8123 D 3.0 / GH 3 46 8125 D 3.0 / GH 5 45 1620 D 3.0 / GH 3 4 45 1621 D 3.0 / GH 5 4 46 8133 D 3.4 / GH 3 46 8135 D 3.4 / GH 5 46 8143 D 3.8 / GH 3 46 8145 D 3.8 / GH 5 46 8153 D 4.5 / GH 3 46 8155 D 4.5 / GH 5 45 1630 D 3.4 / GH 3 2 45 1631 D 3.4 / GH 5 2 45 1640 D 3.8 / GH 3 2 45 1641 D 3.8 / GH 5 2 45 1650 D 4.5 / GH 3 2 45 1651 D 4.5 / GH 5 2 46 8163 D 5.5 / GH 3 46 8165 D 5.5 / GH 5 45 1660 D 5.5 / GH 3 2 45 1661 D 5.5 / GH 5 2 45 1239 D 3.4 45 1249 D 3.8 45 1259 D 4.5 FRIADENT Transfer Coping Slim 2 (without screw) FRIADENT Transfer Post narrow In cases with limited mesio-distal space For impressions following soft-tissue contouring with the Gingiva Former Slim (page 28) Please order PickUp Guide Pin or Standard Abutment Screw separately (page 32) 30 31
Prosthetic Components Esthetic FABRICATION OF THE SUPERSTRUCTURE ON IMPLANT LEVEL Impressions Prosthetics/Lab Impressions Single Components Implant Analogs FRIADENT Transfer Coping Basic For simple impression making in cases with implant divergencies 46 1632 D 3.4 46 1642 D 3.8 46 1652 D 4.5 46 1662 D 5.5 FRIADENT Transfer Post Basic 2 (with PickUp Screw) 45 4020 D 3.0 45 4030 D 3.4 45 4040 D 3.8 45 4050 D 4.5 45 4060 D 5.5 FRIADENT Implant Analog 5 FRIADENT Implant Analog For retaining the prosthetic components on the master model 46 1605 FRIADENT PickUp Guide Pin 4 D 3.0 45 1615 FRIADENT PickUp Guide Pin 4 D 3.4 D 5.5 Try-in Abutments 46 4304 FRIADENT Standard Abutment Screw 4 D 3.0 FRIADENT TransferCap For utmost precision when making impressions Included in delivery of Transfer Copings PickUp and Transfer Technique 45 4305 FRIADENT Standard Abutment Screw 4 D 3.4 D 5.5 45 1629 D 3.0 45 1639 D 3.4 45 1649 D 3.8 45 1659 D 4.5 45 1669 D 5.5 FRIADENT TransferCap 20 Multi-Pack (3 pieces) FRIADENT Select Try-in Abutment 2 45 2119 D 3.0 / A 0 (straight) 45 2120 D 3.4 / A 0 (straight) 45 2121 D 3.8 / A 0 (straight) 45 2122 D 4.5 / A 0 (straight) 45 2123 D 5.5 / A 0 (straight) 45 2219 D 3.0 / A 15 (angled 15 ) 45 2220 D 3.4 / A 15 (angled 15 ) 45 2221 D 3.8 / A 15 (angled 15 ) FRIADENT Select Try-in Abutment Determination of gingival height, Angulation and position of horizontal screw (GH 2) for all FRIADENT prosthetic abutments FRIADENT Select Try-in Abutment 2 Multi-Pack (3 pieces) 45 2193 D 3.4 / A 0 (straight, 3 pieces) 45 2194 D 3.8 / A 0 (straight, 3 pieces) 45 2195 D 4.5 / A 0 (straight, 3 pieces) 45 2196 D 5.5 / A 0 (straight, 3 pieces) 45 2293 D 3.4 / A 15 (angled, 3 pieces) 45 2294 D 3.8 / A 15 (angled, 3 pieces) 32 33
Prosthetics/Lab: Single-tooth Restorations and Bridges Prosthetic Components Esthetic FABRICATION OF THE SUPERSTRUCTURE ON IMPLANT LEVEL EstheticBase Abutments Screws for EstheticBase FRIADENT EstheticBase For esthetically demanding singletooth crowns and bridges Available straight or angled Customizable by grinding Cementable or screw-retained (horizontal or transversal) Please note that the indication of the D 3.0 abutments is restricted to the anterior tooth region. GH 1 1 mm GH 2 2 mm GH 3 3 mm Horizontal Screw Retention All FRIADENT EstheticBase Abutments are provided with a horizontal thread (M 1.4). An additional horizontal or transverse screw is necessary for horizontally screw-retained crowns (page 35). Screwing in of screw for EstheticBase and abutment screw resp. D 3.0: FRIADENT Hex Driver 1.22 mm (page 56) We recommend the use of special titanium drills (Gebr. Brasseler, Lemgo or Jota, Düsseldorf) for preparing the abutments. GH 5 5 mm FRIADENT EstheticBase straight / A 0 with Screw for EstheticBase (D 3.0 Standard Abutment Screw D 3.0) 46 2121 D 3.0 / GH 1 4 46 2122 D 3.0 / GH 2 4 46 2123 D 3.0 / GH 3 4 46 2125 D 3.0 / GH 5 4 46 2131 D 3.4 / GH 1 4 46 2132 D 3.4 / GH 2 4 46 2133 D 3.4 / GH 3 4 46 2135 D 3.4 / GH 5 4 46 2141 D 3.8 / GH 1 2 46 2142 D 3.8 / GH 2 2 46 2143 D 3.8 / GH 3 2 46 2145 D 3.8 / GH 5 2 46 2151 D 4.5 / GH 1 2 46 2152 D 4.5 / GH 2 2 46 2153 D 4.5 / GH 3 2 46 2155 D 4.5 / GH 5 2 46 2161 D 5.5 / GH 1 2 46 2162 D 5.5 / GH 2 2 46 2163 D 5.5 / GH 3 2 46 2165 D 5.5 / GH 5 2 FRIADENT EstheticBase angled / A 15 with Screw for EstheticBase (D 3.0 Standard Abutment Screw D 3.0) 46 2221 D 3.0 / GH 1 4 46 2222 D 3.0 / GH 2 4 46 2223 D 3.0 / GH 3 4 46 2225 D 3.0 / GH 5 4 46 2231 D 3.4 / GH 1 4 46 2232 D 3.4 / GH 2 4 46 2233 D 3.4 / GH 3 4 46 2235 D 3.4 / GH 5 4 46 4304 FRIADENT Standard Abutment Screw 4 D 3.0 46 4305 FRIADENT Screw for EstheticBase 4 D 3.4 D 5.5 46 4403 FRIADENT Horizontal Screw Set Standard Horizontal Screw Standard 4 and Horizontal Screw Seat 8 46 4404 FRIADENT Horizontal Screw Set Long Horizontal Screw Long 4 and Horizontal Screw Seat 8 46 4407 FRIADENT Transverse Screw Set Standard Transverse Screw Standard 4 and Horizontal Screw Seat 8 46 4408 FRIADENT Transverse Screw Set Long Transverse Screw Long 4 and Horizontal Screw Seat 8 46 4401 FRIADENT Horizontal Screw Standard 4 46 4402 FRIADENT Horizontal Screw Long 4 46 4405 FRIADENT Transverse Screw Standard 4 46 4406 FRIADENT Transverse Screw Long 4 45 4410 FRIADENT Horizontal Screw Seat 8 FRIADENT Horizontal Screws Fixing the crown on the oral abutment wall FRIADENT Transverse Screws Fixing the crown on the oral and also the facial abutment wall Double thread length for optimum stability The horizontal screw is used as a transverse screw with D 3.0 and D 3.4 in this case to use a sufficient number of threads The use of horizontal retaining screws with a long head is recommended particularly for molars, because the crown generally offers wider dimensional waxing. Placement of Horizontal Screws: FRIADENT Hex Driver 0.9 mm (page 56) 46 2241 D 3.8 / GH 1 2 46 2242 D 3.8 / GH 2 2 46 2243 D 3.8 / GH 3 2 46 2245 D 3.8 / GH 5 2 46 2251 D 4.5 / GH 1 2 46 2252 D 4.5 / GH 2 2 46 2253 D 4.5 / GH 3 2 46 2255 D 4.5 / GH 5 2 46 2261 D 5.5 / GH 1 2 46 2262 D 5.5 / GH 2 2 46 2263 D 5.5 / GH 3 2 46 2265 D 5.5 / GH 5 2 34 35
Prosthetics/Lab: Single-tooth Restorations and Bridges Prosthetic Components Esthetic FABRICATION OF THE SUPERSTRUCTURE ON IMPLANT LEVEL Ceramic Abutments Cast-to Abutments Please note that the indication for ceramic abutments is restricted to the front-tooth region. FRIADENT CERCON Abutment For full-ceramic restorations with best possible tooth analogy in the anterior region Extremely stable with production from zirconium oxide ceramic Available straight or angled Customizable by grinding or casting Two shades of white, neutral or dentine Outstanding esthetics with brilliant light dynamics Placement of screws: FRIADENT Hex Driver 1.22 mm (page 56) We recommend using the ceramic-line Shaping Set by DeguDent for prepping the FRIADENT CERCON Abutments. The grinding process of CERCON Abutments requires irrigation. FRIADENT CeraBase Two-piece abutment for high-quality ceramic single-tooth restorations in the anterior region Ceramic sleeve with titanium core Available in two sizes (conical and anatomical) Placement of Standard Abutment Screw: FRIADENT Hex Driver 1.22 mm or FRIADENT Slot Screwdriver 2.0 mm (page 56) Grinding of the ceramic sleeve of the FRIADENT CeraBase Abutment: FRIADENT CeraBase ToolSet (page 56) The grinding process does not require irrigation. FRIADENT CERCON Abutment 32 straight / A 0 with screw 47 1141 D 3.8 / GH 1, neutral 47 2141 D 3.8 / GH 1, dentine 47 1151 D 4.5 / GH 1, neutral 47 2151 D 4.5 / GH 1, dentine 47 1142 D 3.8 / GH 2, neutral 47 2142 D 3.8 / GH 2, dentine 47 1152 D 4.5 / GH 2, neutral 47 2152 D 4.5 / GH 2, dentine FRIADENT CERCON Abutment 32 angled / A 15 with screw 47 1241 D 3.8 / GH 1, neutral 47 2241 D 3.8 / GH 1, dentine 47 1251 D 4.5 / GH 1, neutral 47 2251 D 4.5 / GH 1, dentine 47 1242 D 3.8 / GH 2, neutral 47 2242 D 3.8 / GH 2, dentine 47 1252 D 4.5 / GH 2, neutral 47 2252 D 4.5 / GH 2, dentine FRIADENT CeraBase Abutment with Standard Abutment Screw 4 45 2530 D 3.4 conical 30/4 45 2531 D 3.4 anatomical 30/4 45 2540 D 3.8 conical 30/3 45 2541 D 3.8 anatomical 30/3 45 2550 D 4.5 conical 30/3 45 2551 D 4.5 anatomical 30/3 45 2560 D 5.5 conical 30/3 45 2561 D 5.5 anatomical 30/3 Telescopic Abutments 45 2420 D 3.0 45 2430 D 3.4 45 2440 D 3.8 45 2450 D 4.5 45 2460 D 5.5 FRIADENT AuroBase 20/8 with Standard Abutment Screw 4 (D 3.0 with Standard Abutment Screw D 3.0) 45 2620 D 3.0 4 45 2630 D 3.4 4 45 2640 D 3.8 2 45 2650 D 4.5 2 45 2660 D 5.5 2 FRIADENT Telescopic Abutment with Standard Abutment Screw 4 (D 3.0 with Standard Abutment Screw D 3.0) 46 4304 FRIADENT Standard Abutment Screw 4 D 3.0 45 4305 FRIADENT Standard Abutment Screw4 D 3.4 D 5.5 45 2621 D 3.0 45 2631 D 3.4 45 2641 D 3.8 45 2651 D 4.5 45 2661 D 5.5 FRIADENT Milling Implant 6 FRIADENT AuroBase For difficult prosthetic situations requiring individual solutions for crowns, bridges and prostheses For compensation of severe axial divergencies For customized waxing from the top edge of the implant with thin gingiva FRIADENT Telescopic Abutment For simple and economic fabrication of telescopic crowns for fixing prostheses and removable bridges For customized single-tooth crowns Compensation of axial divergencies with customizable milling techniques The Telescopic Abutment can be veneered with titanium ceramics (e.g., Duceratin, Ducera or Vita Titankeramik, Vita Zahnfabrik) for occlusally screwretained single crowns. Screwing in of abutment screw Standard and D 3.0: FRIADENT Hex Driver 1.22 mm or FRIADENT Slot Screwdriver 2.0 mm (page 56) FRIADENT Milling Implant Fixing the prosthetic components in the milling socket Implant analog made of special steel with stronger retainers to resist rotary forces generated by milling 36 37
Prosthetics/Laboratory: CAD/CAM Crowns and bridges Prosthetic Components Esthetic FABRICATION OF THE SUPERSTRUCTURE ON IMPLANT LEVEL Customized abutments (CAD/CAM) Customized abutments (CAD/CAM) TitaniumBase For fabricating ceramic-abutments with customized design Titanium bonding base with prefabricated implant-abutment connection Two flattened sides to protect against rotation ScanBase For scanning the abutment geometry Same design as TitaniumBase, made of plastic, dispenses with use of scan spray or powder Can be used with all conventional dental scanners Extend your workbench use our Compartis Scan&Design Service. 27 9040 D 3.8 27 9050 D 4.5 27 9060 D 5.5 TitaniumBase 4 ScanBase 24 27 9140 D 3.8 27 9150 D 4.5 27 9160 D 5.5 Custom Abutments by Compartis In addition to prosthetic solutions for missing individual teeth or rows of teeth, it is possible to select single-part customized CAD/CAM abutments for the restoration of implants. This adds to your flexibility and the esthetic and functional results. Flexibility with maximum precision Custom Abutments are designed customized. Angulation and shape of the abutment can be designed freely based on a CAD proposal, i.e. with reduced shape of the tooth similar to a prepared tooth stump. Connection geometry and tolerances are milled according to the original measurements with CAM technology to provide a perfect fit of implant and abutment. Optimized soft-tissue management The emergence profile of Custom Abutments can be customized. You have the choice of the laboratory providing an individual gingiva former or to take impressions during surgery and dispensing with a change of abutment. Thus, the soft tissue can be formed immediately after uncovery with the Custom Abutment, so achieving high stability of the soft tissue. Natural esthetics Optionally, Custom Abutments can be made of titanium or zirconium oxide. The zirconium oxide abutments are supplied in colors corresponding to the CERCON abutment. Custom Abutments by Compartis Customized designed and milled abutments for treating patients with individual crowns and bridges with optimal fit Available in titanium and zirconium oxide. Scan and design of the abutments by the dental laboratory with Cercon eye and Cercon art Centralized CAM production of abutments via Compartis DeguDent manufacturing network Extend your workbench use our Compartis Scan&Design Service. Considerable time-savings Patient-customized abutments do not require any refinishing. They are milled exactly according to the design requested and can be inserted in the patient's mouth immediately after delivery. For ordering Custom Abutments by Compartis that are available from DeguDent please contact your local DeguDent distributor or see www.degudent.com. 38 39
Prosthetic Components Esthetic FABRICATION OF THE SUPERSTRUCTURE ON IMPLANT LEVEL Prosthetics/Lab: Overdentures Ball and Socket Attachment LOCATOR FRIADENT Ball and Socket Attachment For fixing overdentures in the mandible Simple protocol with option of chairside restoration Axial divergencies can be compensated Placement of Insert: FRIADENT Seating Instrument for Attachment Insert and MP Insert (page 57) Fixation of Attachment Screw: FRIADENT Hex Driver 1.22 mm (page 56) Activating/Deactivating the Attachment Matrix: FRIADENT Activator/Deactivator for Ball and Socket Attachment (page 57) FRIADENT Attachment Patrix Analog For repairing and relining overdentures Universal for all diameters FRIADENT Ball and Socket Attachment Attachment Insert 2, Attachment Screw 4, Socket 9, with blue silicone ring and white plastic ring 45 3131 D 3.4 / GH 1 4 45 3132 D 3.4 / GH 2 4 45 3133 D 3.4 / GH 3 4 45 3141 D 3.8 / GH 1 2 45 3142 D 3.8 / GH 2 2 45 3143 D 3.8 / GH 3 2 45 3145 D 3.8 / GH 5 2 45 3151 D 4.5 / GH 1 2 45 3152 D 4.5 / GH 2 2 45 3153 D 4.5 / GH 3 2 45 3155 D 4.5 / GH 5 2 45 3161 D 5.5 / GH 1 2 45 3162 D 5.5 / GH 2 2 45 3163 D 5.5 / GH 3 2 45 3165 D 5.5 / GH 5 2 45 3200 FRIADENT Attachment Matrix 9 D 3.4 D 5.5 45 4105 FRIADENT Attachment Patrix Analog5 universal D 3.4 D 5.5 LOCATOR Abutment 4 26 3301 D 3.4 / GH 1 26 3302 D 3.4 / GH 2 26 3303 D 3.4 / GH 3 26 3304 D 3.4 / GH 4 26 3305 D 3.4 / GH 5 26 3311 D 3.8 / GH 1 26 3312 D 3.8 / GH 2 26 3313 D 3.8 / GH 3 26 3314 D 3.8 / GH 4 26 3315 D 3.8 / GH 5 26 3321 D 4.5 / GH 1 26 3322 D 4.5 / GH 2 26 3323 D 4.5 / GH 3 26 3324 D 4.5 / GH 4 26 3325 D 4.5 / GH 5 26 3331 D 5.5 / GH 1.3 26 3332 D 5.5 / GH 2 26 3333 D 5.5 / GH 3 26 3334 D 5.5 / GH 4 26 3335 D 5.5 / GH 5 LOCATOR Replacement Male 41 (4 pieces) 45 3349 clear, strong retention 45 3350 pink, light retention 45 3351 blue, extra light retention 45 3360 gray, zero retention 45 3352 extended range: green, strong retention 45 3353 extended range: orange, light retention 45 3354 extended range: red, extra light retention 45 3355 LOCATOR Impression Coping 42 (4 pieces) 45 3347 LOCATOR Male Processing Package Titanium 43 (2 pieces) 45 3348 LOCATOR Male Processing Package Stainless steel 44 (2 pieces) LOCATOR Female Analog 45 (4 pieces) 45 3356 D 4 45 3357 D 5 45 3358 LOCATOR Black Processing Replacement Male 46 (4 pieces) LOCATOR Overdenture in toothless jaw on two implants Self-righting design for easy fixation in the mouth with one click Low height to give more room, even under limited space conditions Flexible retention for individual determination of prosthesis fixation and balancing of axial divergencies up to 40 Insert LOCATOR abutment: LOCATOR Core Tool 3-piece or FRIADENT LOCATOR Insert for Prosthetic Ratchet (page 57) Content LOCATOR Male Processing Package: 2 x Matrix 2 x Block-Out Spacer 2 x Replacement Male clear, strong retention 2 x Replacement Male pink, light retention 2 x Replacement Male blue, extra light retention 45 3359 LOCATOR Block-Out Spacer 47 (20 pieces) 45 3361 LOCATOR Processing Spacer 48 (4 pieces) 45 3340 LOCATOR Core Tool 49 3-piece 45 3341 LOCATOR Abutment Holder Sleeve 50 (4 pieces) 45 3344 FRIADENT LOCATOR Insert for Prosthetic Ratchet 6 45 3345 LOCATOR Angle Measurement Guide 51 40 41 45 3346 LOCATOR Parallel Post 46 (4 pieces)
Prosthetic Components Multi-Purpose FABRICATION OF THE SUPERSTRUCTURE ON GINGIVA LEVEL Transgingival Extension, Temporary Sealing Impressions MP Abutment Impressions Sets FRIADENT MP Abutment For simple and accurate fabrication of bridges with cast-to or, more economically, with castable waxing sleeve For fixing overdentures by bar construction Inserted abutments remain in the mouth, the laboratory operates on analogs Simplified supragingival impressions and scaffold try-in The MP Abutment consists of MP Abutment Insert and MP Insert Screw. The appropriate MP Abutment is selected according to the gingival height. The number of grooves on the screw head indicates the gingival height of the matching Abutment Insert. GH 1 = 1 ring GH 2 = 2 rings GH 3 = 3 rings GH 5 = 5 rings Placement of MP Abutment Inserts on the implant: FRIADENT Seating Instrument for Attachment Insert and MP Insert (page 57) Fixation of MP Insert Screw: FRIADENT Seating Instrument for MP Insert Screw (page 57) Placement of MP Cover Screw: FRIADENT Hex Driver 0.9 mm (page 56) FRIADENT MP Abutment MP Abutment Insert and MP Insert Screw 46 2831 D 3.4 / GH 1 4 46 2832 D 3.4 / GH 2 4 46 2833 D 3.4 / GH 3 4 46 2835 D 3.4 / GH 5 4 46 2841 D 3.8 / GH 1 2/4 46 2842 D 3.8 / GH 2 2/4 46 2843 D 3.8 / GH 3 2/4 46 2845 D 3.8 / GH 5 2/4 46 2849 D 3.8 / GH 9 2/4 46 2851 D 4.5 / GH 1 2/4 46 2852 D 4.5 / GH 2 2/4 46 2853 D 4.5 / GH 3 2/4 46 2855 D 4.5 / GH 5 2/4 46 2859 D 4.5 / GH 9 2/4 46 2861 D 5.5 / GH 1 2/4 46 2862 D 5.5 / GH 2 2/4 46 2863 D 5.5 / GH 3 2/4 46 2865 D 5.5 / GH 5 2/4 46 1430 D 3.4 46 1440 D 3.8 46 1450 D 4.5 46 1460 D 5.5 FRIADENT MP Cover Screw 2 MP Abutment angled 4 / A 15 46 2932 D 3.4 / GH 2 46 2933 D 3.4 / GH 3 46 2935 D 3.4 / GH 5 MP Abutment angled 4 / A 30 46 3032 D 3.4 / GH 2 46 3033 D 3.4 / GH 3 MP Abutment angled 4 / A 15 46 2942 D 3.8 D 5.5 / GH 2 46 2943 D 3.8 D 5.5 / GH 3 46 2945 D 3.8 D 5.5 / GH 5 MP Abutment angled 4 / A 30 46 3042 D 3.8 D 5.5 / GH 2 46 3043 D 3.8 D 5.5 / GH 3 46 3100 MP Insert Head 4 (as spare part) 46 8230 D 3.4 46 8240 D 3.8 46 8250 D 4.5 46 8260 D 5.5 46 8130 D 3.4 46 8140 D 3.8 46 8150 D 4.5 46 8160 D 5.5 Impressions Single Components Implant Analog FRIADENT MP Lab Set PickUp Impression Content: MP PickUp Impression Coping, MP PickUp Guide Pin, MP Analog FRIADENT MP Lab Set Transfer Impression Content: MP Transfer Impression Coping, MP Analog 42 43 46 1630 D 3.4 46 1640 D 3.8 46 1650 D 4.5 46 1660 D 5.5 46 1635 D 3.4 46 1645 D 3.8 46 1655 D 4.5 46 1665 D 5.5 FRIADENT MP PickUp Impression Coping 2 FRIADENT MP Transfer Impression Coping 2 46 1615 FRIADENT MP PickUp Guide Pin 4 46 4030 D 3.4 46 4040 D 3.8 46 4050 D 4.5 46 4060 D 5.5 FRIADENT MP Analog 5 FRIADENT Impression Coping For transferring the abutment position of to the master model Available for PickUp (open tray) and transfer technique The pre-mounted MP Abutment remains in the implant when making impressions Fixation of MP PickUp Guide Pin: FRIADENT Hex Driver 1.22 mm or FRIADENT Slot Screwdriver 2.0 mm (page 56) Placement of MP Transfer Impression Coping: FRIADENT Hex Driver 0.9 mm (page 56) FRIADENT MP Analog Included in delivery of the MP Lab Sets Impression Is forwarded to the lab with the impression
Prosthetic Components Multi-Purpose FABRICATION OF THE SUPERSTRUCTURE ON GINGIVA LEVEL Prosthetics/Lab: Bridges Bridges Sets Bridges Single Components FRIADENT MP Lab Sets Bridge For simple and accurate fabrication of bridges with cast-to or, more economically, with castable waxing sleeve Can also be used to mill customized bar constructions 46 9530 D 3.4 46 9540 D 3.8 46 9550 D 4.5 46 9560 D 5.5 46 9930 D 3.4 46 9940 D 3.8 46 9950 D 4.5 46 9960 D 5.5 FRIADENT MP Lab Set Bridge with Castable Waxing Sleeve Content: Castable Waxing Sleeve, MP Screw for Waxing Sleeve FRIADENT MP Lab Set Bridge with Cast-to Waxing Sleeve Content: Cast-to Waxing Sleeve, MP Screw for Waxing Sleeve FRIADENT PassivFit Set Soldering Analogs 45 4330 D 3.4 45 4340 D 3.8 45 4350 D 4.5 45 4360 D 5.5 45 4630 D 3.4 45 4640 D 3.8 45 4650 D 4.5 45 4660 D 5.5 FRIADENT Castable Waxing Sleeve 21 FRIADENT Cast-to Waxing Sleeve 20/8 46 4300 FRIADENT MP Screw for Castable Waxing Sleeve 4 D 3.4 D 5.5 Castable Waxing Sleeve: Prior to bridge delivery, the contact surface between crown and abutment and the screw and screw seat are smoothed using the FRIADENT Finishers (page 53). Cast-to Waxing Sleeve: Smoothing with finishers is not necessary. Placement of MP Screw for Waxing Sleeve: FRIADENT Hex Driver 1.22 mm or FRIADENT Slot Screwdriver 2.0 mm (page 56) 45 4830 D 3.4 45 4840 D 3.8 45 4850 D 4.5 45 4860 D 5.5 45 4102 FRIADENT Lab Set Soldering Analog for Bridge FRIADENT Soldering Analog, universal and Soldering Screw for Bridge D 3.4 D 5.5 FRIADENT Soldering Analog For securing the framework in the soldering base 45 4103 FRIADENT Soldering Analog 6, universal D 3.4 D 5.5 45 4207 FRIADENT Soldering Screw for Bridge 4 D 3.4 D 5.5 44 45
Prosthetic Components Multi-Purpose FABRICATION OF THE SUPERSTRUCTURE ON GINGIVA LEVEL Prosthetics/Lab: Bars Bars Sets Bars Single Components FRIADENT MP Lab Sets Bar For fixing overdentures by bar construction Simple and standardized procedure with pre-fabricated round bars (see single components) Customized milled bars are fabricated with castable crown bases (page 44/45). 46 9630 D 3.4 46 9640 D 3.8 46 9650 D 4.5 46 9660 D 5.5 46 9637 D 3.4 46 9647 D 3.8 46 9657 D 4.5 46 9667 D 5.5 46 9638 D 3.4 46 9648 D 3.8 46 9658 D 4.5 46 9668 D 5.5 FRIADENT MP Lab Set Gold Bar Coping Content: Gold Bar Coping, MP Coping Screw FRIADENT MP Lab Set Titanium Bar Coping Content: Titanium Bar Coping, MP Coping Screw FRIADENT MP Lab Set Castable Bar Coping Content: Castable Bar Coping, MP Coping Screw 45 4230 D 3.4 45 4240 D 3.8 45 4250 D 4.5 45 4260 D 5.5 45 4231 D 3.4 45 4241 D 3.8 45 4251 D 4.5 45 4261 D 5.5 45 4530 D 3.4 45 4540 D 3.8 45 4550 D 4.5 45 4560 D 5.5 FRIADENT Gold Bar Coping 9 (without screw) FRIADENT Titanium Bar Coping 2 (without screw) FRIADENT Castable Bar Coping 21 (without screw) 46 4200 FRIADENT MP Coping Screw 4 D 3.4 D 5.5 45 4210 FRIADENT Gold Bar round 9 50 mm length 45 4212 FRIADENT Titanium Bar round 2 50 mm length 45 4215 FRIADENT Gold Bar Clip 9 50 mm length FRIADENT Bar Coping Gold alloy for soldering technique Titanium for laser welding Cast-to for customized waxing Placement of MP Coping Screw: FRIADENT Hex Driver 1.22 mm or FRIADENT Slot Screwdriver 2.0 mm (page 56) Activating the Bar Clip: FRIADENT Bar Clip Activator (page 57) Soldering Analogs 45 4101 FRIADENT Lab Set Soldering Analog for Bar FRIADENT Soldering Analog, universal and Soldering Screw for Bar D 3.4 D 5.5 FRIADENT Soldering Analog For securing the framework in the soldering base 45 4103 FRIADENT Soldering Analog 6 universal D 3.4 D 5.5 45 4206 FRIADENT Soldering Screw for Bar 4 D 3.4 D 5.5 46 47
Prosthetic Components Special TG prosthetic components are available for prosthetic restoration of transgingival TG implants. The prosthetic diameter is identical for all implant diameters. Healing Impressions Prosthetic restoration CROWNS AND BRIDGES Crowns on TG Abutment Page 52 TRANSGINGIVAL Crowns on TG AuroBase Page 52 TG Cover Screw Page 9 TG Impression Coping Page 50 IMMEDIATE RESTORATION TG Impression Coping Page 50 OVERDENTURES Bar constructions on TG Bar Copings Page 53 Overdenture on TG Attachments Page 54 Overdenture on TG AuroBase Page 52 48 49
Prosthetic Components Impressions, Posthetics/Lab Impressions, Posthetics/Lab: Bridges Impressions Sets Bridges Sets TG Impression Copings For transferring the transgingival implant position to the master model Available for PickUp (open tray) and transfer technique Transfer Impression Coping short for making impressions with an existing overdenture 25 9112 TG Clinical Set PickUp Impression (4 PickUp Impression Copings with 4 TG PickUp Guide Pins) 25 9100 TG Clinical Set Transfer Impression (4 Transfer Impression Copings) 25 9105 TG Clinical Set Transfer Impression (short) (4 short Transfer Impression Copings) Bridges Single Components 25 9900 TG Lab Set Bridge (Castable Waxing Sleeve) (4 TG Castable Waxing Sleeves, 4 TG Abutment Screws) 25 9905 TG Lab Set Bridge (Cast-to Waxing Sleeve) (4 TG Cast-to Waxing Sleeves, 4 TG Abutment Screws) TG Lab Set Bridge For simple and accurate fabrication of bridges with cast-to or, more economically, with castable waxing sleeve Can also be used to mill customized bar constructions If, in cases of implant divergencies, a transfer of the head square is not required, the FRIADENT MP Transfer Impression Coping D 3.8 is used (page 44). This impression coping is compatible with all diameters of TG. Fixation of TG PickUp Guide Pin: FRIADENT Hex Driver 1.22 mm or FRIADENT Slot Screwdriver 2.0 mm (page 56) TG Implant-Soldering Analog For retaining the prosthetic components on the master model as well as for securing the framework in the soldering base Impressions Single Components Implant Analogs 25 1805 TG PickUp Impression Coping 2 with PickUp Guide Pin 25 1600 TG Transfer Impression Coping 2 25 1605 TG Transfer Impression Coping (short) 2 25 1701 TG PickUp Guide Pin 4 25 9405 TG Implant-Soldering Analog 6 (4 TG Implant-Soldering Analogs) 25 4010 TG Implant-Soldering Analog 6 Soldering Analogs 25 4245 TG Castable Waxing Sleeve 21 with TG Abutment Screw 25 4246 TG Cast-to Waxing Sleeve 20/8 with TG Abutment Screw 25 4300 TG Abutment Screw 4 25 9305 TG Lab Set Implant-Soldering Analog 6 (Bridge) (4 TG Implant-Soldering Analogs, 4 TG Abutment Screws) 25 4105 TG Lab Set Soldering Analog Bridge TG Implant-Soldering Analog with TG Abutment Screw Placement of TG Abutment Screw for TG Abutment and AuroBase: FRIADENT Hex Driver 1.22 mm or FRIADENT Slot Screwdriver 2.0 mm (page 56) 50 51
Prosthetic Components Prosthetics/Lab: Bridges and Single-tooth Restorations Prosthetics/Lab: Overdentures Esthetic Abutments Bar Sets TG Abutment For fabrication of single-tooth crowns and bridges Available straight and angled Customizable by grinding Horizontally screw-retained Horizontal Screw All TG Abutments are provided with a horizontal thread (M 1.4). An additional horizontal or transverse screw is necessary for horizontally screw-retained crowns (page 35). We recommend the use of special titanium drills (Gebr. Brasseler, Lemgo or Jota, Düsseldorf) for preparing the abutments. Cast-to Abutment 25 4500 TG Abutment 2 straight / A 0 with TG Abutment Screw 25 4510 TG Abutment 2 angled / A 15 with TG Abutment Screw Bar Single Components 25 9600 TG Lab Set Gold Bar Coping (4 TG Gold Copings, 4 TG Coping Screws) 25 9700 TG Lab Set Titanium Bar Coping (4 TG Titanium Copings, 4 TG Coping Screws) 25 9800 TG Lab Set Castable Bar Coping (4 TG Castable Copings, 4 TG Coping Screws) 25 4240 TG Gold Bar Coping 9 with TG Coping Screw 25 4241 TG Titanium Bar Coping 2 with TG Coping Screw TG Lab Set Bar Coping For fixing overdentures by bar construction Simple and standardized procedure with pre-fabricated round bars (see single components) Customized milled bars are fabricated with castable TG crown bases (page 52) FRIADENT Bar Copings Gold alloy for soldering technique Titanium for laser welding Cast-to for customized waxing TG AuroBase For customized shaping of crowns and bridge abutments For compensation of axial divergencies Placement of TG Abutment Screw for TG Abutment and AuroBase: FRIADENT Hex Driver 1.22 mm or FRIADENT Slot Screwdriver 2.0 mm (page 56) 25 4520 TG AuroBase 20/8 with TG Abutment Screw 25 4300 TG Abutment Screw 4 25 4242 TG Castable Bar Coping 21 with TG Coping Screw 25 4200 TG Coping Screw 4 45 4210 FRIADENT Gold Bar round 9 50 mm length 45 4212 FRIADENT Titanium Bar round 2 50 mm length Placement of TG Coping Screw: FRIADENT Hex Driver 1.22 mm or FRIADENT Slot Screwdriver 2.0 mm (page 56) Activating the Bar Clip: FRIADENT Bar Clip Activator (page 57) 45 4215 FRIADENT Gold Bar Clip 9 50 mm length Soldering Analogs 25 9306 TG Lab Set Implant-Soldering Analog 6 (Bar) (4 Implant-Soldering Analogs, 4 TG Coping Screws) 25 4106 TG Lab Set Soldering Analog Bar 6 52 TG Implant-Soldering Analog with 53 TG Coping Screw
Prosthetic Components Prosthetic Instruments Prosthetics/Lab: Overdentures Ball and Socket Attachment Instrument Sets TG Attachment For fixing overdentures in the mandible Simple protocol with option of chairside restoration Axial divergencies can be compensated 25 4401 TG Attachment 2/4 46 7000 FRIADENT Prosthetic Set Mini The Prosthetic Set Mini includes all instruments required for the prosthetic delivery of implant restorations ( Esthetic protocol). Content: FRIADENT Ratchet Ratchet Hex Driver 0.9 mm/short Ratchet Hex Driver 1.22 mm/short 26 8020 Basic Set Prosthetics The set includes all instruments required for impression making and prosthetics. The instruments are supplied in the Prosthetic Tray. Content: FRIADENT Rachet Handpiece Hex Driver 0.9 mm/short Handpiece Hex Driver 0.9 mm/long Handpiece Hex Driver 1.22 mm/short Handpiece Hex Driver 1.22 mm/long Handle for Handpiece Hex Driver Ratchet Hex Driver 0.9 mm/short Ratchet Hex Driver 0.9 mm/long Ratchet Hex Driver 1.22 mm/short Ratchet Hex Driver 1.22 mm/long Seating Instrument for Attachment Insert and MP Insert Handpiece Seating Instrument for MP Insert Screw Ratchet Seating Instrument for MP Insert Screw Insertion Tool EstheticBase FRIADENT Select Try-in Abutment D 3.0/A 0 FRIADENT Select Try-in Abutment D 3.4/A 0 FRIADENT Select Try-in Abutment D 3.8/A 0 FRIADENT Select Try-in Abutment D 4.5/A 0 FRIADENT Select Try-in Abutment D 5.5/A 0 FRIADENT Select Try-in Abutment D 3.0/A 15 FRIADENT Select Try-in Abutment D 3.4/A 15 FRIADENT Select Try-in Abutment D 3.8/A 15 26 8025 Prosthetic Tray (empty) 54 55
Prosthetic Instruments Single Instruments Single Instruments 45 5709 FRIADENT Ratchet 6 without inserts 45 5605 FRIADENT Seating Instrument 2 for Transfer Coping FRIADENT Ratchet Hex Driver 6 with torque limit 45 5617 FRIADENT Seating Instrument 2 for Attachment Insert and MP Insert 45 5732 Width 0.9 mm/14 Ncm/short 45 5733 Width 0.9 mm/14 Ncm/long 45 5734 Width 1.22 mm/24 Ncm/short 45 5736 Width 1.22 mm/24 Ncm/long FRIADENT Ratchet Slot Screwdriver 6 with torque limit 45 5714 Blade width 2.0 mm/14 Ncm/short 45 5722 Blade width 2.0 mm/14 Ncm/long FRIADENT Handpiece HexDriver 6 46 5710 Width 0.9 mm/short 46 5720 Width 0.9 mm/long 46 5711 Width 1.22 mm/short 46 5721 Width 1.22 mm/long FRIADENT Handpiece Slot Screwdriver 6 46 5610 FRIADENT Ratchet Seating Instrument 6 for MP Insert Screw with torque limit 46 5615 FRIADENT Handpiece Seating Instrument 6 for MP insert screw for contra-angle handpiece 45 5621 FRIADENT Activator 6 for Ball and Socket Attachment 45 5622 FRIADENT Deactivator 6 for Ball and Socket Attachment 45 3340 LOCATOR Core Tool 49 3-piece 45 3344 FRIADENT LOCATOR Insert for Prosthetic Ratchet 6 45 3345 LOCATOR Angle Measurement Guide 51 45 5623 FRIADENT Bar Clip Activator 6 46 5712 Blade width 2.0 mm/short 46 5722 Blade width 2.0 mm/long 45 5702 FRIADENT Finisher 6/10 for Horizontal Screw Set This handle fits all contra-angle handpiece drivers. The 0.9 mm FRIADENT Hex Driver without torque limit is recommended for regions with limited access. 46 5750 FRIADENT Handle for Handpiece Hex Driver 6 45 5650 FRIADENT Hex Driver 6 without torque limit width 0.9 mm 45 5618 FRIADENT Mounting device for Hex Driver FRIADENT Finisher 6/10 for Abutment Seat for Screw-retained Superstructures 45 5705 45 5707 D 5.5 45 5700 FRIADENT Finisher6/10 for Screw Head Seat for Screw-retained Superstructures 45 5753 FRIADENT CeraBase Diamond Milling Tool Medium 45 5755 FRIADENT CeraBase Diamond Milling Tool Fine 45 5709 45 5623 45 5621 45 5622 56 57
Presentation Material Materials Demo Models Metals Patient Information Material CD-ROMs for Presentations 45 9981 FRIADENT Acrylic Model Maxilla without prosthetics (ANKYLOS,, FRIALIT ) 45 9982 FRIADENT Acrylic Model Maxilla with prosthetics (ANKYLOS,, FRIALIT ) 45 9985 Acrylic Model Mandible without prosthetics (bar construction) 45 9986 Acrylic Model Mandible with prosthetics (bar construction) 26 9110 Large Scale Model Set 5:1 5 002032 DENTSPLY Friadent Waiting Room Brochure 5 702002 Waiting Room Poster Matthew (Single tooth gap) 5 702004 Waiting Room Poster Ian (Free-end situation/bridge) 5 702005 Waiting Room Poster Heather (edentulous/implant-borne overdenture) 5 702006 Indication Poster 5 001033 DENTSPLY Friadent Implant Pass 66 7021 Picture CD 66 1077 ExpertEase Picture CD 66 1078 CAD/CAM Picture CD 66 1036 DENTSPLY Friadent Picture CD 66 1037 CERCON Picture CD 66 1038 Picture CD for Internet, all systems 66 1039 FRIADENT plus Picture CD Type Index Composition Titanium 1 Ti grade 1 Titanium 2 Ti grade 2 Titanium 3 Ti grade 4 Titanium 4 Ti6Al4V grade 5 Aluminium 5 AlMg 3 Stainless steel 6 Surgical Steel Stainless steel 49 316L SS SS/303 SE Stainless steel 51 316L SS Brass 7 CuZn Cast-to alloy* 8 Au: 60%, Pt: 19%, Pd: 20%, Ir: 1% Gold alloy** 9 Au: 68,6%, Pt: 2,4%, Pd: 4%, Ag: 11,8%, Cu: 10,6%, Ir: 0,1%, Zn: 2,5% Hard metal 10 K 40 Polyethylen/Aluminium 42 LDPE/6061 T6 Al Polyamid/Polyethylen/Stainless steel/plastics 43 Nylon/LDPE/Ti6AI4V/Silicone Rubber Polyamid/Polyethylen/Stainless steel/plastics 44 Nylon/LDPE/303 SE SS/Silicone Rubber Aluminium 45 6061 T6 Aluminum Brass/Polyoxymethylene 48 MS-002, DELRIN, 1/4" Brass/Polysulfon 50 MS-013-1 POLYSULFONE (3/8") * TEC 11.9 x 10-6 K -1, pre-heating temperature < 850 C, cast temperature < 1450 C; ** melting interval from 880 940 C 58 59 Plastics Type Index Composition Polyoxymethylene (POM) 20 Polymethylmethacrylate (PMMA) 21 Polystyrene 22 Polytetrafluourethylene 23 Polyetheretherketone (PEEK) 24 Polyetherimide 25 Silicone 26 Silicone 47 Silicone Rubber Polycarbonate 27 Polypropylene 28 Polyamid 41 Zytel 101l Nylon Polyethylen/Aluminium 42 LDPE/6061 T6 Al Polyamid/Polyethylen/Stainless steel/plastics 43 Nylon/LDPE/Ti6AI4V/Silicone Rubber Polyamid/Polyethylen/Stainless steel/plastics 44 Nylon/LDPE/303 SE SS/Silicone Rubber Polyethylen 46 LDPE Brass/Polyoxymethylene 48 MS-002, DELRIN, 1/4" Brass/Polysulfon 50 MS-013-1 POLYSULFONE (3/8") Ceramics Type Index Composition Aluminium oxide 30 Al 2 O 3 Hydroxyapatite 31 Ca 5 (PO 4 ) 3 OH Zirconium oxide 32 ZrO 2 PRESENTATION MATERIAL
Smartphone: Go to PDF of this product catalog Some products may not be available in all countries. Please contact your DENTSPLY Friadent representative to obtain up to date information on the product range and on availability. 6-702031/009 Manufacturer: Friadent GmbH P. O. Box 71 01 11 68221 Mannheim/Germany Phone +49 621 4302-1265 Fax +49 621 47 13 06 e-mail: friadent@dentsply.com for Class I Devices for Class II a, II b and III Devices Manufacturer of FRIOS Handpieces and FRIOS Unit S/i: W&H Dentalwerk Bürmoos GmbH 5111 Bürmoos/Austria Manufacturer of Custom Abutments by Compartis : DeguDent GmbH 63403 Hanau/Germany Manufacturer of FRIADENT Locator : ZEST ANCHORS, LLC. 2061 Wineridge Place Escondido, CA 92029/USA EC Representative: Wellkang Ltd. 29 Harley St. W1G 9QR London/ U.K. for Class I Devices for Class II a, II b and III Devices www.dentsply-friadent.com 0412/2.0/SB