Trio Q Data Radios Licensed UHF Ethernet and Serial Data QR450
1 The Trio Q Data Radios are advanced high speed licensed digital data radios, which provide both Ethernet and serial communications for the most complex and demanding applications in Point-to-Point and Point-to-Multipoint (Multiple Address Radio) Telemetry and remote SCADA systems. Features such as ChannelShare+, web-based user configuration, together with powerful remote diagnostics and Network Management, make Trio Q Data Radios the complete licensed radio solution that works with all leading host systems and remote equipment. Combining both Ethernet and serial connectivity, the Trio Q Data Radios are suitable for use with the latest SCADA technology as well as providing a smooth transition from serial-based infrastructure to IP/Ethernet.
Product Data Sheet Trio QR450 Specifications 2 Trio QR450 Radio Frequency Range 400-450MHz (M-Band) or 450-520MHz (H-Band) Frequency Splits Various Tx/Rx frequency splits - configurable Channel Selection 3.125kHz channel steps Channel Spacing 12.5 and 25kHz (software selectable) Frequency Accuracy ±0.5ppm, -40 to +70 C (-40 to 158 F) ambient Aging <= 1ppm/annum Radio Modes Simplex and Half duplex Configuration Configuration via embedded HTTP, HTTPS web interface & or Telnet/SSH/Serial console Transmitter Tx Power 0.05 to 10W (+17 to +40dBm) +/- 0.1dB configurable with over-temperature and high VSWR protection Modulation Configurable narrow band digitally filtered binary CPM, 4, 8 and 16 level FSK Tx Keyup Time <1ms Timeout Timer Configurable 0 to 255 seconds Tx Spurious <= -37dBm PTT Control Auto (Data) / RTS line on Data Port Receiver AFC Tracking Digital receiver frequency tracking Mute Configurable digital mute Connections Serial Com Port 1/2 1 x DB9 female connector providing 2 x RS-2 3-wire serial ports or 1x RS485 serial port (shared connector). Serial Interface Speeds From 600bps up to 115,200bps Serial Com Port Flow Control Configurable hardware / software / 3-wire interface Serial Com Port DCD Control Configurable DCD operation : activated on RF carrier or from user data output Ethernet Port 2 x RJ45: 10/100 Mbps (auto-mdix sensing) compliant with IEEE 802.3 Antenna 1 x TNC female bulkhead Power 2-pin locking, mating connector supplied USB port Firmware Upgrade, Configuration & Diagnostics logs (Future release) LED Display Multimode Indicators for Pwr, Tx, Rx, Sync, TxD and RxD data LEDs and LAN LEDs Ethernet Ethernet Protocols Ethernet/IP (including UDP, TCP, DHCP, ARP, ICMP, STP, IGMP, SNTP & TFPT) Ethernet Repeating Automatic and Self Learning Peer to Peer repeating Operating Modes Layer-2 Ethernet Bridge mode / Layer-3 IP Router mode Ethernet Traffic Filtering Configurable: No Filtering / Unicast Traffic & ARP Only / Unicast Traffic Only / List of approved MAC addresses Compression Automatic Ethernet data compression Terminal Server Legacy RS-2 serial support via embedded terminal server (UDP/TCP) DHCP Modes Auto and Manual SNMP SNMP V1,V2c, RFC 1213-compliant & radio diagnostics parameters (with traps) Modbus Gateway Configurable MODBUS/TCP to MODBUS/RTU Gateway Embedded Ping Tester Internal ping test facility Specifications continue on the next page
Product Data Sheet Trio QR450 Specifications 3 Trio QR450 Modem RF Channel Data Rate # Region Bandwidth (KHz) Speed (Kbps) RF Sens (1x10E-6 BER) Dynamic Speed Selection Operating Modes Channelshare+ Backward Compatibility Firmware Security Encryption* HTML Interface Console Interface Password Protection Diagnostics FCC 12.5 8 16 24 25 16 48 64 ACMA/ETSI 12.5 8 16 24 25 14 28 42 56 QoS/RSSI based Automatic Speed Selection or Fixed speed mode Base, remote, repeater or store n forward Advanced dynamic supervisory collision avoidance system Backward compatible with Trio E-Series radios Local and over-the-air flash-based firmware upgradable patches with support for broadcast updates 256-bit AES Password Protected HTTP and HTTPS configuration and management interface Password protected Telnet, SSH and Serial console interface Password protected configuration sessions -116-111 -105-97 -114-109 -103-96 -113-110 -107-100 -114-109 -103-96 Diagnostics Overview Network management and diagnostic Windows GUI software Network-wide operation from any remote terminal Non intrusive protocol runs simultaneously with the application Storage of data error and channel occupancy statistics In-built Error Rate testing capabilities Diagnostics parameters available Transmitter Power Received Signal Strength DC Supply Voltage Received Frequency Error Radio Temperature VSWR Event Log General Operating Temperature Range Power Supply Transmit Current Receive Current Housing & Dimensions Mounting Weight Warranty Approvals and Certifications Europe (ETSI) Internal Event Logging facility -40 to +70 C (-40 to 158 F) ambient 13.8Vdc nominal (10-30Vdc) 1.6A nominal @ 1W, 2.7A nominal @ 5W, 3.7A nominal @ 10W <330mA nominal @ 13.8Vdc Rugged die-cast, 115 x 34 x 164mm Integrated Mounting Holes or DIN Rail mounting (optional) 0.5kg (1.1lbs.) 3 years on parts and labor ETSI EN300113, EN301489, EN60950 FCC FCC PART 15, PART 90 Industry Canada Australia Hazardous Locations IC RS119, ICES-001 ACMA AS4295-1995 (Data) CSA Class I, Division II, Groups (A,B,C,D) for Hazardous Locations ANSI/UL equivalent)
Product Data Sheet Trio QR450 Model 6 Model TBURQ R TBURQR4ab-cccdeef represents the part number matrix Trio Radio QR450 Q Data Radios Select: Unit Type Simplex/Half Duplex Radio Select: Generic Frequency Band 4 UHF: 400-520 MHz Band L H H E00 F00 E N 0L 1L Select: Sub Band - UHF Low Band : 400 to 450MHz High Band : 450 to 520MHz Select: Hazardous Area Approvals CSA & ATEX Hazardous (Standard) Select: Modulation ETSI/ACMA Region FCC Region Select: Encryption (subject to country of use) 256-bit AES encryption (standard) No encryption Select: Licensed Feature Serial Data Only (Two Serial Ports) Ethernet & Serial (Three Ethernet & two Serial Ports) Select: Power Supply 0 10-30V DC Standard Example: TBURQR4LH-E00E1L0 specifies: Trio QR450 remote station, 400 to 450MHz, hazardous area approved, modulation for ETSI/ACMA regions, 256 bit Encryption enabled, two Ethernet & two Serial Ports, 10-30V DC power supply Communications Standards: FCC Federal Communications Commission (USA) IC Industry Canada ETSI European Telecommunication Standards Institute ACMA Australian Communications and Media Authority * Export restrictions may apply. Contact your local representative for more details. Note: Not all product features are available in every mode of operation. Note: Some radio models may not be available in your country. Local and regulatory conditions may determine the performance and suitability of the radio in different countries. It is the responsibility of the buyer to ensure the radio model meets the regulatory conditions required. Contact your local Schneider Electric sales office for more details.
Trio Q Data Radios Licensed UHF Ethernet and Serial Data QB450
1 The Trio Q Data Radio is an advanced high speed licensed digital data radio which provides both Ethernet and serial communications for the most complex and demanding applications in Point-to-Point and Point-to-Multipoint (Multiple Address Radio) Telemetry and remote SCADA systems. Features such as ChannelShare+, web-based user configuration, together with powerful remote diagnostics and Network Management, make Q Data Radios the complete licensed radio solution that works with all leading host systems and remote equipment. Combining both Ethernet and serial connectivity, the Trio Q Data Radio are suitable for use with the latest SCADA technology as well as providing a smooth transition from serial-based infrastructure to IP/ Ethernet.
Product Data Sheet Trio QB450 Specifications 2 Trio QB450 Radio Frequency Range 400-450MHz (L-Band) or 450-520MHz (H-Band) Frequency Splits Various Tx/Rx frequency splits - configurable Channel Selection 3.125kHz channel steps Channel Spacing 12.5 and 25kHz (software selectable) Frequency Accuracy ±0.5ppm, -40 to +70 C (-40 to 158 F) ambient Aging <= 1ppm/annum Radio Modes Simplex, Half duplex & Full duplex Duplexer Optional external duplexer available for single antenna operation Configuration Configuration via embedded HTTP, HTTPS web interface & or Telnet/SSH/Serial console Transmitter Tx Power 0.05 to 10W (+17 to +40dBm) +/- 0.1dB configurable with over-temperature and high VSWR protection Modulation Configurable narrow band digitally filtered binary CPM, 4, 8 and 16 level FSK Tx Keyup Time <1ms Timeout Timer Configurable 0 to 255 seconds Tx Spurious <= -37dBm PTT Control Auto (Data) Receiver AFC Tracking Digital receiver frequency tracking Mute Configurable digital mute Connections Serial Com Port 1/2 1 x DB9 female connector providing 2 x RS-2 3-wire serial ports or 1x RS485 serial port (shared connector). Serial Interface Speeds From 600bps up to 115,200bps Serial Com Port Flow Control Configurable hardware / software / 3-wire interface Serial Com Port DCD Control Configurable DCD operation : activated on RF carrier or from user data output Ethernet Port 3 x RJ45: 10/100 Mbps (auto-mdix sensing) compliant with IEEE 802.3 Antenna 2 x N female bulkhead (seperate Tx and Rx ports - full duplex) or optional 1 x N female bulkhead (single Tx/Rx port - half duplex) Power (Supply voltage options) 10-pin locking, mating connector supplied or optional (10-30Vdc/36-72Vdc) or 100-250Vac IEC socket USB port Firmware Upgrade, Configuration & Diagnostics logs (Future release) LED Display Multimode Indicators for Pwr, Tx, Rx, Sync, TxD and RxD data LEDs and LAN LEDs Ethernet Ethernet Protocols Ethernet/IP (including UDP, TCP, DHCP, ARP, ICMP, STP, IGMP, SNTP & TFPT) Ethernet Repeating Automatic and Self Learning Peer to Peer repeating Operating Modes Layer-2 Ethernet Bridge mode / Layer-3 IP Router mode Ethernet Traffic Filtering Configurable: No Filtering / Unicast Traffic & ARP Only / Unicast Traffic Only / List of approved MAC addresses Compression Automatic Ethernet data compression Terminal Server Legacy RS-2 serial support via embedded terminal server (UDP/TCP) DHCP Modes Auto and Manual SNMP SNMP V1,V2c, RFC 1213-compliant & radio diagnostics parameters (with traps) Modbus Gateway Configurable MODBUS/TCP to MODBUS/RTU Gateway Embedded Ping Tester Internal ping test facility Specifications continue on the next page
Product Data Sheet Trio QB450 Specifications 3 Trio QB450 Modem RF Channel Data Rate # Region Bandwidth (KHz) Speed (Kbps) RF Sens (1x10E-6 BER) Dynamic Speed Selection Operating Modes Channelshare+ Backward Compatibility Firmware Security Encryption* HTML Interface Console Interface Password Protection Diagnostics FCC 12.5 8 16 24 25 16 48 64 ACMA/ETSI 12.5 8 16 24 25 14 28 42 56 QoS/RSSI based Automatic Speed Selection or Fixed speed mode Base, remote, repeater or store n forward Advanced dynamic supervisory collision avoidance system Backward compatible with Trio E-Series radios Local and over-the-air flash-based firmware upgradable patches with support for broadcast updates 256-bit AES Password Protected HTTP and HTTPS configuration and management interface Password protected Telnet, SSH and Serial console interface Password protected configuration sessions -116-111 -105-97 -114-109 -103-96 -113-110 -107-100 -114-109 -103-96 Diagnostics Overview Network management and diagnostic Windows GUI software Network-wide operation from any remote terminal Non intrusive protocol runs simultaneously with the application Storage of data error and channel occupancy statistics In-built Error Rate testing capabilities Diagnostics parameters available Transmitter Power Received Signal Strength DC Supply Voltage Received Frequency Error Radio Temperature VSWR Event Log General Operating Temperature Range Internal Fan Power Supply Protection mode Transmit Current** Receive Current** Housing & Dimensions Weight Warranty Approvals and Certifications Europe (ETSI) Internal Event Logging facility -40 to +70 C (-40 to 158 F) ambient Internal automatic thermostatically controlled fan 10-30Vdc (nominal) or optional 36-72Vdc or 100-250Vac power supply Full duplex (not protected) or optional half duplex (protected) hardware variants 4A nominal @ 1W, 5.1A nominal @ 5W, 6.1A nominal @ 10W 1A nominal @ 13.8Vdc 19 1 RU rack mount, 483 x 45 x 410mm 5kg (11lbs.) 3 years on parts and labor ETSI EN300113, EN301489, EN60950 FCC FCC PART 15, PART 90 Industry Canada Australia IC RS119, ICES-001 ACMA AS4295-1995 (Data)
Product Data Sheet Trio QB450 Model 6 Model TBURQ B P TBURQB4ab-cccdeef represents the part number matrix Trio Radio QB450 Q Data Radios Select: Unit Type Full Duplex Radio - 19 1RU Half Duplex Protected Radio - 19 1RU Select: Generic Frequency Band 4 UHF: 400-520 MHz Band L H N E00 F00 E N 0L 1L Select: Sub Band - UHF Low Band : 400 to 450MHz High Band : 450 to 520MHz Select: Hazardous Area Approvals No Approval Select: Modulation ETSI/ACMA Region FCC Region Select: Encryption (subject to country of use) 256-bit AES encryption (standard) No encryption Select: Licensed Feature Serial Data Only (Two Serial Ports) Ethernet & Serial (Three Ethernet & two Serial Ports) Select: Power Supply 0 Redundant 10-30V DC Standard 1 Redundant -48V DC 2 Non-Redundant 110/240V AC 3 Redundant 110/240V AC Example: TBURQB4LN-E00E1L0 specifies: Trio QB450 base station, 400 to 450MHz, modulation for ETSI/ACMA regions, 256 bit Encryption enabled, three Ethernet & two Serial Ports, redundant 10-30V DC power supply. Communications Standards: FCC Federal Communications Commission (USA) IC Industry Canada ETSI European Telecommunication Standards Institute ACMA Australian Communications and Media Authority * Export restrictions may apply. Contact your local representative for more details. ** In high ambient temperature situations, the internal fans may operate, resulting in additional current consumption of upto 2 Amps. Note: Not all product features are available in every mode of operation. Note: Some radio models may not be available in your country. Local and regulatory conditions may determine the performance and suitability of the radio in different countries. It is the responsibility of the buyer to ensure the radio model meets the regulatory conditions required. Contact your local Schneider Electric sales office for more details.
Trio Q Data Radios Licensed UHF Ethernet and Serial Data QH450
1 The Trio Q Data Radio is an advanced high speed licensed digital data radio which provides both Ethernet and serial communications for the most complex and demanding applications in Point-to-Point and Point-to-Multipoint (Multiple Address Radio) Telemetry and remote SCADA systems. Features such as ChannelShare+, web-based user configuration, together with powerful remote diagnostics and Network Management, make Q Data Radios the complete licensed radio solution that works with all leading host systems and remote equipment. Combining both Ethernet and serial connectivity, the Trio Q Data Radio are suitable for use with the latest SCADA technology as well as providing a smooth transition from serial-based infrastructure to IP/ Ethernet.
Product Data Sheet Trio QH450 Specifications 2 Trio QH450 Radio Frequency Range 400-450MHz (L-Band) or 450-520MHz (H-Band) Frequency Splits Various Tx/Rx frequency splits - configurable Channel Selection 3.125kHz channel steps Channel Spacing 12.5 and 25kHz (software selectable) Frequency Accuracy ±0.5ppm, -40 to +70 C (-40 to 158 F) ambient Aging <= 1ppm/annum Radio Modes Full duplex Duplexer Optional external duplexer available for single antenna operation Configuration Configuration via embedded HTTP, HTTPS web interface & or Telnet/SSH/Serial console Transmitter Tx Power 0.05 to 10W (+17 to +40dBm) +/- 0.1dB configurable with over-temperature and high VSWR protection Modulation Configurable narrow band digitally filtered binary GMSK, 4, 8 and 16 level FSK Tx Keyup Time <1ms Timeout Timer Configurable 0 to 255 seconds Tx Spurious <= -37dBm PTT Control Auto (Data) Receiver AFC Tracking Digital receiver frequency tracking Mute Configurable digital mute Connections (for each Base within the Hot Standby configuration) Serial Data Port 1 x RS2 DB9 female connector providing 2 x RS-2 3-wire serial ports (shared connector). 300-38,400 bps asynchronous Serial Data Port Flow Control Configurable hardware / software / 3-wire interface Serial Data Port DCD Control Configurable DCD operation : activated on RF carrier or from user data output Ethernet Port 3 x RJ45: 10/100 Mbps (auto-mdix sensing) compliant with IEEE 802.3 Antenna 2 x N female bulkhead (seperate Tx and Rx ports - full duplex) or optional 1 x N female bulkhead (single Tx/Rx port - half duplex) Power (Supply voltage options) 10-pin locking, mating connector supplied or optional (10-30Vdc/36-72Vdc) or 100-250Vac IEC socket USB port Firmware Upgrade, Configuration & Diagnostics logs (Future release) LED Display Multimode Indicators for Pwr, Tx, Rx, Sync, TxD and RxD data LEDs and LAN LEDs Ethernet Ethernet Protocols Ethernet/IP (including UDP, TCP, DHCP, ARP, ICMP, STP, IGMP, SNTP & TFPT) Ethernet Repeating Automatic and Self Learning Peer to Peer repeating Operating Modes Layer-2 Ethernet Bridge mode / Layer-3 IP Router mode Ethernet Traffic Filtering Configurable: No Filtering / Unicast Traffic & ARP Only / Unicast Traffic Only / List of approved MAC addresses Ethernet Link Monitoring Monitor the Ethernet link between a base unit and up to two remote IP addresses Compression Automatic Ethernet data compression Terminal Server Legacy RS-2 serial support via embedded terminal server (UDP/TCP) DHCP Modes Auto and Manual SNMP SNMP V1,V2c, RFC 1213-compliant & radio diagnostics parameters (with traps) Modbus Gateway Configurable MODBUS/TCP to MODBUS/RTU Gateway Embedded Ping Tester Internal ping test facility Specifications continue on the next page
Product Data Sheet Trio QH450 Specifications 3 Trio QH450 Modem RF Channel Data Rate # Region Bandwidth (KHz) Speed (Kbps) RF Sens (1x10E-6 BER) Dynamic Speed Selection Operating Modes Channelshare+ Backward Compatibility Firmware Security Encryption* HTML Interface Console Interface Password Protection Hot Standby Controller FCC 12.5 8 16 24 25 16 48 64 ACMA/ETSI 12.5 8 16 24 25 14 28 42 56 QoS/RSSI based Automatic Speed Selection or Fixed speed mode Base, remote, repeater or store n forward Advanced dynamic supervisory collision avoidance system Backward compatible with Trio E-Series radios Local and over-the-air flash-based firmware upgradable patches with support for broadcast updates 256-bit AES Password Protected HTTP and HTTPS configuration and management interface Password protected Telnet, SSH and Serial console interface Password protected configuration sessions -116-111 -105-97 -114-109 -103-96 -113-110 -107-100 -114-109 -103-96 Change-over control Alarm Monitoring Diagnostics Manual (forced) / automatic / remote (software driven) Tx Power Failure / Receiver Failure / Received Signal Frequency Error / Data Corruption / DC Power Supply Fail Diagnostics Overview Network management and diagnostic Windows GUI software Network-wide operation from any remote terminal Non intrusive protocol runs simultaneously with the application Storage of data error and channel occupancy statistics In-built Error Rate testing capabilities Diagnostics parameters available Transmitter Power Received Signal Strength DC Supply Voltage Received Frequency Error Radio Temperature VSWR Event Log General Operating Temperature Range Internal Fan Power Supply Protection mode Housing & Dimensions Weight Warranty Approvals and Certifications Europe (ETSI) Internal Event Logging facility -40 to +70 C (-40 to 158 F) ambient Internal automatic thermostatically controlled fan 10-30Vdc or optional 36-72Vdc or 100-250Vac power supply Full duplex (not protected) or optional half duplex (protected) hardware variants Hot Standby is configured using 2 x QB450 (19 1 RU each) plus 1 x Hot Standby Controller (19 1 RU each) for a total of 19 3RU s (424.3 x 1 x 436.5mm ) 15kg (33Ibs) excluding optional duplexer 3 years on parts and labor ETSI EN300113, EN301489, EN60950 FCC FCC PART 15, PART 90 Industry Canada Australia IC RS119, ICES-001 ACMA AS4295-1995 (Data)
Product Data Sheet Trio QH450 Model 6 TBURQH4ab-cccdeef represents the part number matrix Model Trio Radio QH450 TBURQ H Q Data Radios Select: Unit Type Full Duplex Hot Standby Kit (with controller) - 19 3RU Comprised of 2 x QB + Controller Select: Generic Frequency Band 4 UHF: 400-520 MHz Band L H N E00 F00 E N 1L Select: Sub Band - UHF Low Band : 400 to 450MHz High Band : 450 to 520MHz Select: Hazardous Area Approvals No Approval Select: Modulation ETSI/ACMA Region FCC Region Select: Encryption (subject to country of use) 256-bit AES encryption (standard) No encryption Select: Licensed Feature Ethernet & Serial (Three Ethernet & two Serial Ports) Select: Power Supply 0 10-30V DC Standard 1-48V DC 2 Single 110/240V AC A B Select: Hot Standby Controller Options Common Tx/Rx Antenna Duplicated Tx/Rx Antennas Note: Refer to the next page for further details on the Hot Standby Controller Options.
COM 1/2 ETH1 ETH2 ETH3 COM 1/2 COM 1/2 COM 1/2 AUX ETH1 ETH2 ETH3 Factory Default AUX Base A ETH1 COM 1/2 AUX ETH1 ETH2 ETH3 Factory Default AUX USB COM1 Com2 Error Pwr Sync Rxd Rxd No < Green Tx NoRx Txd Txd Yes < Red Base B ETH1 Select A Auto B USB COM1 Com2 Error Pwr Sync Rxd Rxd No < Green Tx NoRx Txd Txd Yes < Red Product Data Sheet Trio QH450 Dimensions and Options 6 QH450 - Hot Standby Full Duplex Radio - Dimensions 16.69 (424mm) 17.18 (436.5mm) QB450 16.7 (424.3mm) 15.91 (404.3mm) 15 (381mm) 16.7 (424mm) 15.91 (404.3mm) 5.19 (1mm) QHHSC QB450 18.87 (479.3mm) QH450 - Hot Standby Controller Kit Configurations QHHSC - Option Descriptions Kit Configuration TBURQH4xx-xxxxxxxA 2 x TBURQB4xx-xxxxxxx 1 x TBURQHHSC-00A QB450 QB450 Tx Rx QHHSC Hot Standby Controller Option A A B Description LNA (Rx) & RF Relay (Tx) Fitted Duplicated Tx/Rx Ports Antenna Type Common Tx/Rx Antenna Duplicated Tx/Rx Antennas TBURQH4xx-xxxxxxxB 2 x TBURQB4xx-xxxxxxx 1 x TBURQHHSC-00B QB450 QB450 B #Note The QH450 is a full duplex radio platform and must be deployed with suitable band pass duplexer or external filters. Internal Duplexers are not available. Suitable duplexers include TBURDUPLXBP4XXCOA. For information regarding external duplexers, contact your local sales office. LNA (Low Noise Receiver Amplifier / Splitter) RELAY (Coaxial Transmitter Switch) EXTERNAL DUPLEXER 2013 Schneider Electric. All rights reserved - February 2014 Telemetry & Remote SCADA Solutions www.schneider-electric.com Document Number TBULMxxxxxx-xx
Trio Q Data Radios Licensed UHF Ethernet and Serial Data QP450
1 The Trio Q Data Radio is an advanced high speed licensed digital data radio which provides both Ethernet and serial communications for the most complex and demanding applications in Point-to-Point and Point-to-Multipoint (Multiple Address Radio) Telemetry and remote SCADA systems. Features such as ChannelShare+, web-based user configuration, together with powerful remote diagnostics and Network Management, make Q Data Radios the complete licensed radio solution that works with all leading host systems and remote equipment. Combining both Ethernet and serial connectivity, the Trio Q Data Radio are suitable for use with the latest SCADA technology as well as providing a smooth transition from serial-based infrastructure to IP/ Ethernet.
Product Data Sheet Trio QP450 Specifications 2 Radio Frequency Range Frequency Splits Channel Selection Channel Spacing Frequency Accuracy Aging Radio Modes Configuration Transmitter Tx Power Modulation Tx Keyup Time Timeout Timer Tx Spurious PTT Control Receiver AFC Tracking Mute Connections Serial Com Port 1/2 Serial Interface Speeds Serial Com Port Flow Control Serial Com Port DCD Control Trio QP450 400-450MHz (L-Band) or 450-520MHz (H-Band) Various Tx/Rx frequency splits - configurable 3.125kHz channel steps 12.5 and 25kHz (software selectable) ±0.5ppm, -40 to +70 C (-40 to 158 F) ambient <= 1ppm/annum Simplex or Half duplex Configuration via embedded HTTP, HTTPS web interface & or Telnet/SSH/Serial console 0.05 to 10W (+17 to +40dBm) +/- 0.1dB configurable with over-temperature and high VSWR protection Configurable narrow band digitally filtered binary CPM, 4, 8 and 16 level FSK <1ms Configurable 0 to 255 seconds <= -37dBm Auto (Data) Digital receiver frequency tracking Configurable digital mute 1 x DB9 female connector providing 2 x RS-2 3-wire serial ports or 1x RS485 serial port (shared connector). From 600bps up to 115,200bps Configurable hardware / software / 3-wire interface Configurable DCD operation : activated on RF carrier or from user data output Ethernet Port 3 x RJ45: 10/100 Mbps (auto-mdix sensing) compliant with IEEE 802.3 Antenna Power (Supply voltage options) USB port LED Display Ethernet Ethernet Protocols Ethernet Repeating Operating Modes Ethernet Traffic Filtering Compression Terminal Server DHCP Modes SNMP Modbus Gateway Embedded Ping Tester Specifications continue on the next page Optional: (See diagram at end of datasheet for detailed information) - 2 x N female bulkhead (Refer Option B) - 2 x N female bulkhead (Refer Option D) - 1 x N female bulkhead (Refer Option E) 10-pin locking, mating connector supplied or optional (10-30Vdc/-48Vdc) or 100-250Vac IEC socket Firmware Upgrade, Configuration & Diagnostics logs (Future release) Multimode Indicators for Pwr, Tx, Rx, Sync, TxD and RxD data LEDs and LAN LEDs Ethernet/IP (including UDP, TCP, DHCP, ARP, ICMP, STP, IGMP, SNTP & TFPT) Automatic and Self Learning Peer to Peer repeating Layer-2 Ethernet Bridge mode / Layer-3 IP Router mode Configurable: No Filtering / Unicast Traffic & ARP Only / Unicast Traffic Only / List of approved MAC addresses Automatic Ethernet data compression Legacy RS-2 serial support via embedded terminal server (UDP/TCP) Auto and Manual SNMP V1,V2c, RFC 1213-compliant & radio diagnostics parameters (with traps) Configurable MODBUS/TCP to MODBUS/RTU Gateway Internal ping test facility
Product Data Sheet Trio QP450 Specifications 3 Trio QB450 Modem RF Channel Data Rate # Region Bandwidth (KHz) Speed (Kbps) RF Sens (1x10E-6 BER) Dynamic Speed Selection Operating Modes Collision Avoidance Backward Compatibility Firmware Security Encryption* HTML Interface Console Interface Password Protection Diagnostics FCC 12.5 8 16 24 25 16 48 64 ACMA/ETSI 12.5 8 16 24 25 14 28 42 56 QoS/RSSI based Automatic Speed Selection or Fixed speed mode Base, remote, repeater or store n forward Channelshare+ - Advanced dynamic supervisory collision avoidance system Carrier Sense - Carrier sense based collision avoidance system Backward compatible with Trio E-Series radios Local and over-the-air flash-based firmware upgradable patches with support for broadcast updates 256-bit AES Password Protected HTTP and HTTPS configuration and management interface Password protected Telnet, SSH and Serial console interface Password protected configuration sessions -116-111 -105-97 -114-109 -103-96 -113-110 -107-100 -114-109 -103-96 Diagnostics Overview Network management and diagnostic Windows GUI software Network-wide operation from any remote terminal Non intrusive protocol runs simultaneously with the application Storage of data error and channel occupancy statistics In-built Error Rate testing capabilities Diagnostics parameters available Transmitter Power Received Signal Strength DC Supply Voltage Received Frequency Error Radio Temperature VSWR Event Log General Operating Temperature Range Internal Fan Power Supply Protection mode Transmit Current** Receive Current** Housing & Dimensions Weight Warranty Approvals and Certifications Europe (ETSI) Internal Event Logging facility -40 to +70 C (-40 to 158 F) ambient Internal automatic thermostatically controlled fan 10-30Vdc (nominal) or, for option B hardware, optional -48Vdc or 100-250Vac power supply Half duplex - Automatic or manual changeover between internal modules 4A nominal @ 1W, 5.1A nominal @ 5W, 6.1A nominal @ 10W 1A nominal @ 13.8Vdc 19 1 RU rack mount, 483 x 45 x 410mm 5kg (11lbs.) 3 years on parts and labor ETSI EN300113, EN301489, EN60950 FCC FCC PART 15, PART 90 Industry Canada Australia IC RS119, ICES-001 ACMA AS4295-1995 (Data)
Product Data Sheet Trio QP450 Model 6 Model TBURQ P TBURQP4ab-cccdeef represents the part number matrix Trio Radio QB450 Q Data Radios Select: Unit Type Half Duplex Protected Radio - 19 1RU Select: Generic Frequency Band 4 UHF: 400-520 MHz Band L H N E00 F00 E N 1L Select: Sub Band - UHF Low Band : 400 to 450MHz High Band : 450 to 520MHz Select: Hazardous Area Approvals No Approval Select: Modulation ETSI/ACMA Region FCC Region Select: Encryption (subject to country of use) 256-bit AES encryption (standard) No encryption Select: Licensed Feature Ethernet & Serial (Three Ethernet & two Serial Ports) Select: Power Supply 0 10-30V DC Standard 1-48V DC (Option B Only) 3 Dual 110/240V AC (Option B Only) B D E Select: Hot Standby Options Duplicated Tx/Rx Ports Separate switched Tx & Rx Ports Common switched Tx/Rx Port Example: TPURQB4LN-E00E1L0B specifies: Trio QP450 Redundant half duplex radio, 400 to 450MHz, modulation for ETSI/ACMA regions, 256 bit Encryption enabled, three Ethernet & two Serial Ports, 10-30V DC power supply, Duplicated Tx/Rx Ports. Communications Standards: FCC Federal Communications Commission (USA) IC Industry Canada ETSI European Telecommunication Standards Institute ACMA Australian Communications and Media Authority * Export restrictions may apply. Contact your local representative for more details. ** In high ambient temperature situations, the internal fans may operate, resulting in additional current consumption of upto 2 Amps. Note: Not all product features are available in every mode of operation. Note: Some radio models may not be available in your country. Local and regulatory conditions may determine the performance and suitability of the radio in different countries. It is the responsibility of the buyer to ensure the radio model meets the regulatory conditions required. Contact your local Schneider Electric sales office for more details.
6 Product Data Sheet Trio QP450 Model QP450 - Hot Standby Half Duplex Radio - Dimensions QP450 - Hot Standby Half Duplex Options Hot Standby Options QP450 Hot Standby Option Descriptions QP450 Tx/Rx Tx/Rx B B Description Duplicated Tx/Rx Ports Antenna Type Duplicated Tx/Rx Antennas QP450 Tx Rx D D E Separate Switched Tx & Rx Ports Common Switched Tx/Rx Port Separate Tx & Rx Antennas Common Tx/Rx Antenna QP450 Tx/Rx E RELAY (Coaxial Transmitter Switch) 2013 Schneider Electric. All rights reserved - February 2014 Telemetry & Remote SCADA Solutions www.schneider-electric.com Document Number TBULMxxxxxx-xx