DMP Industrial Pressure Transmitter for Low Pressure Stainless Steel Sensor accuracy according to IEC 60770: standard: 0.5 % FSO option: 0.5 / 0. % FSO from 0... 00 mbar up to 0... 40 bar Output signals -wire: 4... 0 ma -wire: 0 0 ma / 0 0 V others on request Special characteristic perfect thermal behaviour excellent long term stability pressure port G /" flush from 00 mbar Optional versions IS-version Ex ia = intrinsically safe for gases and dusts SIL -according to IEC 6508 / IEC 65 pressure sensor welded The pressure transmitter DMP can be used in all industrial areas when the medium is compatible with stainless steel.4404 (6 L) or.445 (6 L). Additional are different elastomer seals as well as a helium tested welded version available. The modulare concept of the device allows to combine different stainless steel sensors and electronic modules with a variety of electrical and mechanical versions.thus a diversity of variations is created, meeting almost all requirements in industrial applications. Preferred areas of use are Plant and Machine Engineering Environmental Engineering (water - sewage - recycling) Energy Industry specific versions BD SENSORS GmbH BD-Sensors-Straße Tel: +49 (0) 9 5 / 98-0 www.bdsensors.com D - 9599 Thierstein Fax: +49 (0) 9 5 / 98 - info@bdsensors.de
DMP Input pressure range gauge / abs. [bar] - 0 0.0 0.6 0.5 0.40 0.60.6 Overpressure [bar] 5 0.5 5 5 0 Burst pressure [bar] 7.5.5.5.5 7.5 7.5 5 gauge / abs. [bar].5 4 6 0 6 5 40 Overpressure [bar] 0 0 40 40 80 80 05 Burst pressure [bar] 5 5 50 50 0 0 0 Vacuum resistance P N bar: unlimited vacuum resistance P N < bar: on request Output signal / Supply Standard -wire: 4... 0 ma / V S = 8... V DC Option IS-protection -wire: 4... 0 ma / V S = 0... 8 V DC Options -wire -wire: 0... 0 ma / V S = 4... 0 V DC 0... 0 V / V S = 4... 0 V DC Performance Accuracy standard: nominal pressure < 0.4 bar: ± 0.5 % FSO nominal pressure 0.4 bar: ± 0.5 % FSO option : nominal pressure 0.4 bar: ± 0.5 % FSO option : for all nominal pressure: ± 0. % FSO Permissible load current -wire: R max = [(V S V S min) / 0.0 A] Ω current -wire: R max = 500 Ω voltage -wire: R min = 0 kω Influence effects supply: 0.05 % FSO / 0 V load: 0.05 % FSO / kω Long term stability ± 0. % FSO / year at reference conditions Response time -wire: 0 msec -wire: msec accuracy according to IEC 60770 limit point adjustment (non-linearity, hysteresis, repeatability) Thermal effects (Offset and Span) P N [bar] - 0 < 0.40 0.40 Tolerance band [% FSO] ± 0.75 ± ± 0.75 in compensated range [ C] -0... 85 0... 70-0 85 Permissible temperatures Permissible temperatures medium: -40... 5 C electronics / environment: -40... 85 C storage: -40... 00 C Electrical protection Short-circuit protection permanent Reverse polarity protection no damage, but also no function Electromagnetic compatibility emission and immunity according to EN 66 Mechanical stability Vibration 0 g RMS (5... 000 Hz) according to DIN EN 60068--6 Shock 500 g / msec according to DIN EN 60068--7 Materials Pressure port stainless steel.4404 (6 L) Housing stainless steel.4404 (6 L) Option compact field housing stainless steel.405 (0), cable gland brass, nickel plated others on request Seals (media wetted) standard: FKM options: EPDM NBR welded version others on request Diaphragm stainless steel.445 (6 L) Media wetted parts pressure port, seals, diaphragm welded version only with pressure ports according to EN 87 Explosion protection (only for 4 0 ma / -wire) Approvals IBExU 0 ATEX 068 X / IECEx IBE.007X DX9-DMP zone 0: II G Ex ia IIC T4 Ga zone 0: II D Ex ia IIIC T 85 C Da Safety technical maximum values U i = 8 V, I i = 9 ma, P i = 660 mw, C i 0 nf, L i 0 µh, the supply connections have an inner capacity of max. 7 nf to the housing Permissible temperatures for in zone 0: -0... 60 C with p atm 0.8 bar up to. bar environment in zone or higher: -0... 70 C Connecting cables (by factory) cable capacitance: signal line/shield also signal line/signal line: 60 pf/m cable inductance: signal line/shield also signal line/signal line: µh/m pressure and level
DMP Miscellaneous Option SIL according to IEC 6508 / IEC 65 Current consumption signal output current: max. 5 ma signal output voltage: max. 7 ma Weight approx. 40 g Installation position any 4 Operational life > 00 x 0 6 pressure cycles CE-conformity EMC Directive: 004/08/EC ATEX Directive 94/4/EG only for 4 0 ma / -wire, not in combination with the accuracy 0.% 4 Pressure transmitters are calibrated in a vertical position with the pressure connection down. If this position is changed on installation there can be slight deviations in the zero point for pressure ranges P N bar. Wiring diagrams -wire-system (current) p supply + -wire-system (current / voltage) p supply + V S I supply VS supply I / U signal + A / V Pin configuration Electrical connection ISO 4400 Supply + Supply Signal + (for -wire) Electrical connections (dimensions in mm) Binder 7 (5-pin) 4 Mx / metal (4-pin) Shield ground pin 5 4 field housing IN + IN - OUT+ cable colours (DIN 4700) wh (white) bn (brown) gn (green) ye/gn (yellow / green) standard option ISO 4400 Binder Series 7 5-pin Mx 4-pin cable outlet with PVC cable (IP 65) (IP 67) (IP 67) (IP 67) 5 compact field housing cable outlet, cable with ventilation tube (IP 67) (IP 68) 6 universal field housing stainless steel.4404 (6 L) with cable gland M0x.5 (ordering code 880) and other versions on request 5 standard: m PVC cable without ventilation tube (permissible temperature: -5... 70 C) 6 different cable types and lengths available, permissible temperature depends on kind of cable www.bdsensors.com
DMP Mechanical connections (dimensions in mm) standard for accuracy 0.5 / 0.5 % standard for accuracy 0. %; SIL- and SIL-IS-version G/" DIN 85 G/" DIN 85 with ISO 4400 with ISO 4400 option G/" EN 87 G/" open port G/" DIN 85 with flush sensor G/4" DIN 85 G/4" EN 87 /" NPT /4" NPT metric threads and other versions on request This data sheet contains product specification, properties are not guaranteed. Subject to change without notice. pressure Tel and +49 level (0) 9 5 / 98-0 www.bdsensors.com Fax +49 (0) 9 5 / 98 - info@bdsensors.de DMP_E_080
Ordering code DMP DMP - - - - - - - Pressure gauge absolute 0 Input [bar] 0.0 0 0 0 0.6 6 0 0 0.5 5 0 0 0.40 4 0 0 0 0.60 6 0 0 0.0 0 0.6 6 0.5 5 0 4.0 4 0 0 6.0 6 0 0 0 0 0 6 6 0 5 5 0 40 4 0 0-0 X 0 9 9 9 Output 4 0 ma / -wire 0 0 ma / -wire 0 0 V / -wire Intrinsic safety 4 0 ma / -wire SIL 4 0 ma / -wire SIL with intrinsic safety 4 0 ma / -wire E S ES Accuracy standard for P N 0.4 bar 0.5 % standard for P N < 0.4 bar 0.5 % 5 option for P N 0.4 bar 0.5 % option 0. % Electrical connection Male and female plug ISO 4400 Male plug Binder series 7 (5-pin) Cable outlet with PVC cable Cable outlet Male plug Mx (4-pin) / metal 0 0 0 0 T A 0 T R 0 M 0 Compact field housing stainless steel.405 8 5 0 9 9 Mechanical connection G/" DIN 85 G/" EN 87 G/4" DIN 85 G/4" EN 87 0 0 0 0 0 0 4 0 0 G/" DIN 85 with flush sensor F 0 0 G/" DIN 85 open pressure port /" NPT /4" NPT H 0 0 N 0 0 N 4 0 9 9 Seals FKM EPDM NBR without (welded version) 4 5 Special version standard 0 0 0 9 9 not in combination with SIL standard: m PVC cable without ventilation tube (permissible temperature: -5 70 C), others on request cable with ventilation tube (code TR0 = PVC cable), different cable types and lengths available, price without cable 4 welded version only with pressure ports according to EN 87 07.0.0 This dokument contains product specification; properties are not guaranteed. Detailed information about options are defined in the datasheet. Subject to change without notice.