BeoSound 9000. Reference book

BeoSound 9000 Reference book

CAUTION: To reduce the risk of electric shock, do not reove cover (or back). No User-serviceable arts inside. Refer servicing to qualified service ersonnel. WARNING: To revent fire or electric shock, do not exose this aliance to rain or oisture. Do not exose this equient to driing or slashing and ensure that no objects filled with liquids, such as vases, are laced on the equient. To coletely disconnect this equient fro the AC Mains, disconnect the ower suly cord lug fro the AC recetacle. This sybol indicates that a dangerous voltage constitut ing a risk of electric shock is resent within this unit. This sybol indicates that there are iortant oerating and aintenance instructions in the literature accoanying this unit.

BeoSound 9000 The usic entertainent centre 3 The BeoSound 9000 is an extraordinary CD layer with a built-in radio. BeoSound 9000 gives you erfect sound reroduction and changes tracks and CDs at a foridable ace. You will exerience six Coact Discs as one iece of usic virtually one CD. The syste can be laced anywhere you want usic in traditional laceents; on a table, hanging on a wall, or on the secially designed, vertical stand. The choice is yours. The BeoSound 9000 reresents a new and visual way of exeriencing usic.

BeoVision Avant Guide BeoVision Avant Reference book 4 Contents of the Reference book To get to know your Bang & Olufsen roduct, two guides are at your disosal. The Guide The Guide rovides inforation on daily use. The Reference book gives a thorough overview of all asects. To the right, you find the contents of this Reference book, the ain chaters of the Guide are listed below: Your key to using BeoSound 9000, 4 Using the CD layer, 6 Using the radio, 9 Adjust the volue, 10 The Reference book Before you start 6 Cautions How to set u BeoSound 9000 7 Placing your BeoSound 9000 9 Centering the CD drive echanis 33 Otion rograing Connect the cables 10 Aerial 10 Loudseakers 10 Extra equient 10 Master Link 11 Digital outut 11 To the ains Getting started 12 Close-u oeration anel Set the tie 13 Using the built-in clock Playing CDs 18 Loading CDs 19 CD layback Playing CDs in different ways 20 Choosing a sequence of discs 20 Playing CDs and tracks in rando order Playing favourite CD tracks 21 Select and store a series of tracks 21 Enable or disable layback of a track series Nae your CDs 22 Nae a CD 22 See the list of CD naes Positioning CDs 23 Load and adjust a CD anually 23 Clear the ositioning Make BeoSound 9000 start or sto at a secific tie 14 Set a Tier 15 Set a Tier for single date 15 Set a weekly Tier 16 Checking or clearing Tiers 17 Switching the Tier function on or off 17 Choose location for the Tier function Dislay CD inforation 24 Switching between dislays Playing other sources 25 Listen to external sources

5 Using the radio 26 Presetting radio stations 26 Clearing resets Looking after BeoSound 9000 34 Cleaning BeoSound 9000 35 Handling your CDs Key to using this guide Use this key to identify what a button, source or status dislay looks like in an instruction sequence. Otiise radio sound The PIN-code syste RADIO CD Buttons on the BeoSound 9000 close- 27 Fine tuning a radio station 36 Activate the PIN-code syste u oeration anel or 27 Mono/stereo recetion 36 Change or delete a PIN-code on the Beo4 reote 37 Using your PIN-code control 37 Did you forget your PIN-code? Nae radio stations CD EDIT? Dislays on the BeoSound 9000 28 Naing radio stations 28 Clear a nae CD Dislays on the Beo4 RANDOM reote control Play your radio stations 29 Playing radio 29 Switching between dislays Adjust and store sound settings 30 Sound adjustents Using the Beo4 reote control 31 Beo4 reote control oeration Use BeoSound 9000 with a video syste 32 A fully integrated setu 32 An AV integrated setu 33 Otion rograing

6 Before you start We recoend that you follow this rocedure when you set u your BeoSound 9000: Place the BeoSound 9000 where you want to use it. If you wish to ount BeoSound 9000 on a wall bracket or floor stand accessory, then asseble the accessory according to the folder enclosed with it. Set u your loudseakers (or, if the BeoSound 9000 is to be used in a Bang & Olufsen AV syste, set u this syste) following the rocedures described in the guides enclosed with these roducts. Connect all cables to their sockets on the rear anel of the BeoSound 9000 reeber not to connect it to the ains yet! Arrange the cables in the cable cover grooves and attach the cover to the rear of the BeoSound. Connect BeoSound 9000 to the ains. Cautions Make sure that the BeoSound 9000 is set u, laced and connected, in accordance with the instructions in this guide. The BeoSound 9000 is designed for indoor use in dry, doestic environents only, and for use within a teerature range of 10 40 C (50 105 F). Avoid lacing the BeoSound 9000 in direct sunlight or direct artificial light (e.g. a sotlight), or near objects generating electrical noise (e.g. diers), as this will reduce the sensitivity of the reote control receiver. Place the BeoSound 9000 so that ventilation will not be ieded, and reeber to leave enough sace above or in front of the BeoSound 9000 for the glass door to oen, and to facilitate close-u oeration. If you are going to hang the BeoSound 9000 on the wall, always use the correct size and tye of screws and wall lugs to suort the weight of the BeoSound 9000 (deending on the aterial and the construction of the wall). If in doubt, consult your Bang & Olufsen retailer. If you wish to hang BeoSound 9000 on the wall we recoend that you conceal the cables using the otional Cable Covers, as shown on the oosite age. When you are lifting the BeoSound 9000 out of the box we recoend that you, in order to avoid fingerarks on the surfaces, use the two foa acking shells laced at each end of the BeoSound 9000. Light artition walls are often constructed of gysu anels known as drywall or wall board secured to vertical studs. Gysu is not a satisfactory aterial to suort the weight of the BeoSound 9000! If you wish to hang your BeoSound 9000 on a gysu wall, using one of the brackets, we recoend that at least one ounting screw be a lag screw, which is screwed securely into a vertical wall stud.

How to set u BeoSound 9000 7 As illustrated in this section, BeoSound 9000 is designed for a variety of laceents. It can be laced on a secial stand, on a shelf or a table in various ositions or hanging on the wall (using one of the otional wall brackets). This section also describes how to centre the CD echanis for the different setu situations entioned here this is very iortant for the roer functioning of the CD layer! The section Getting started describes how to turn the close-u oeration anel (and the dislay) so it can be read fro your referred angle. Fig. 1: The BeoSound 9000 laced in a vertical osition. When BeoSound 9000 is laced like this, the CD echanis ust be centred for a vertical osition. The Stand is sulied with two different sets of feet: sikes for use on a careted floor rubber feet for use on a non-careted floor. Do not lift or ove the Stand around while the BeoSound 9000 is ounted on it. Fig. 2: The BeoSound 9000 hung flat on the wall in a high horizontal osition. When BeoSound 9000 is laced like this, the CD echanis ust be centred for a horizontal osition. Fig. 3: The BeoSound 9000 hung flat on the wall in a vertical osition. When BeoSound 9000 is laced like this, the CD echanis ust be centred for a vertical osition. NOTE! Deending on the laceent you have chosen for your BeoSound 9000, the carriage will situate itself in various ositions. If you choose to lace BeoSound 9000 vertically, the carriage will ove to the to end of BeoSound 9000. If you choose to lace the BeoSound 9000 horizontally, the carriage will situate itself next to the oeration anel.

8 >> How to set u BeoSound 9000 Fig. 4: The BeoSound 9000 laced flat on a level surface, e.g. a table or shelf. When BeoSound 9000 is laced like this, the CD echanis ust be centered for a flat osition (factory setting). Fig. 5: The BeoSound 9000 laced in a slant osition on a level surface, e.g. a table or shelf. When BeoSound 9000 is laced like this, the CD echanis ust be centered as for a flat osition (factory setting). Fig. 6: The BeoSound 9000 laced in a near uright osition on a level surface, e.g. a table or shelf. When BeoSound 9000 is laced like this, the CD echanis ust be centered for a horizontal osition. Fig. 7: The BeoSound 9000 hung low on the wall in a near uright osition. When BeoSound 9000 is laced like this the CD echanis ust be centered for a horizontal osition.

9 Centering the CD drive echanis The CD echanis is sring susended in order to ake the BeoSound 9000 arty-safe. By centering the CD echanis, you adjust the tension of the sring susension to allow for different laceents. a It is very iortant for the functioning of the CD layer that you adjust the sring susension correctly! The sring susension in the two adjustent holes can be set to four different ositions: b a) Use this setting when BeoSound 9000 is laced in the Bracket as in figs 6 and 7. b) Use this setting when BeoSound 9000 is laced either on its Stand, or hung vertically on the wall as in figs 1 and 3. d c c) Use this setting when BeoSound 9000 is hung horizontally on the wall as in fig 2. d) Use this setting when BeoSound 9000 is laced either flat on a table, or in the Bracket as in figs 4 and 5. This is the factory setting. How to center the sring susension Enclosed with the Stand and the Brackets, you will find a sall lastic tool, which you ust use for this urose: > Locate the two adjustent holes in the botto late of BeoSound 9000. > Pry off the two sall lastic lugs (using the chisel-shaed end of the tool). > Insert the other end of the tool (the arrowshaed end) and turn the tool so that the arrow in each hole oints into the correct direction. > When finished ut back the two lastic lugs again. In all but the flat and the near flat ositions, both arrows in the holes ust oint uwards when finished. In the flat osition (factory setting) they ust oint towards the centre of BeoSound 9000.

10 Connect the cables You can use your BeoSound 9000 in a stand-alone setu or connected to a Bang & Olufsen video syste with a Master Link cable. The Master Link Master Link connection socket on the back of BeoSound 9000 can also be used for AM aerial Extra equient FM aerial the distribution of sound to any roo you like. Use the diagra and the label on the Loudseakers socket anel for reference when locating the sockets. Do not connect the BeoSound 9000 to the ains until you have finished connecting the cables. Digital outut Aerial connections In order to obtain otial recetion of radio stations it is essential to use the correct tye of aerial (FM and/or AM) or cable net connection. Let your Bang & Olufsen retailer advise you. > Connect your FM signal to the socket arked FM and your AM signal, if any, to the socket arked AM. > When using indoor aerials (either an FM diole or AM loo aerial), tune in to the radio station you want and then turn the aerial horizontally until otiu signal is received. Loudseakers You ay choose to loo the signals through fro seaker to seaker, as entioned in the User s guide for your loudseakers, or you ay connect one seaker to each of the two sockets. > Connect your active Bang & Olufsen loudseakers to the sockets arked PL. Reeber to set the L R LINE switch on your active seakers to L and R (left and right channel), resectively. Extra equient The AUX socket enables you to connect e.g. a tae recorder or a record layer (with built-in realifier). However, as this socket does not carry Data Link signals, you will not be able to oerate the connected equient by reote control. Just select A.AUX and then oerate the extra equient close-u. > Connect your extra equient to the socket arked AUX. Master Link connection You can connect a video syste or BeoLink syste to the Master Link socket, in order to achieve an integrated AV syste. The AV syste ay be set u in one roo, or slit u on two roos. The Master Link connection ay also be used to distribute sound to other roos in the house, in a BeoLink syste. For further inforation, lease contact your retailer. > Using a Master Link cable, connect one end to the socket arked ML (Master Link) on the BeoSound 9000 and the other end to the corresonding socket on the TV. NOTE! For further inforation about a setu other than the stand-alone otion, lease refer to Use BeoSound 9000 with a video syste.

11 Digital outut The socket arked DIG. OUT carry the digital signals fro the CD layer, and is intended for connecting digital equient (outut only). Mains connection Plug the ains lead into the socket arked ~. When you have ade all the connections, relace the cover to hide the socket coartent. Reove the cover in the botto late of the BeoSound 9000 to gain access to the sockets. The socket coartent contains the socket for the ains cord. The cover has two erforated sections, which you can ry off in order to ake a hole through which to run the cables. Select one in an aroriate osition to suit your setu. If you have set u the BeoSound 9000 on the Stand, (see How to set u BeoSound 9000), a different cover ust be used. This new cover is sulied with the Stand. Finally, connect the BeoSound 9000 (and the other units in your syste) to the ains. For safety reasons fasten the ains cord as shown, before running it out fro the socket coartent.

12 Getting started When you have finished the setting u rocedure, the BeoSound 9000 is ready for use. Kee BeoSound 9000 in stand-by ode to facilitate easy access and to ensure that Clock and Tier settings are always available. Close-u oeration anel In order to ake reading easier in all laceent situations, you can rotate the close-u oeration anel (and thus the dislay): > Turn off the ower. > Oen the lid to gain access to the close-u oeration anel. > Lift off the oeration anel by inserting a finger where indicated, lift the anel out, rotate it, and insert it again (connectors first). Lift here When you turn on the BeoSound 9000 a tiny red light aears in the dislay, indicating that the syste is in stand-by ode, ready to be used. > Press the load button to oen the glass door. > Reove the carton stri behind the CD cla and the foa acking (these ites are for rotection of the CD drive and the glass door during transort). 1 2 You can rotate the CD claer lid (with the Bang & Olufsen nae) in order to ensure that the nae always aears in a horizontal osition (and not uside down).

Set the tie 13 The BeoSound 9000 has a built-in clock indicating tie, date and year. If you want to ake use of the Tier function described on the following ages, you ust first ake sure that the built-in clock in the BeoSound 9000 has been set correctly. You can check the clock on the dislay to ensure that it is set correctly. If this is not the case you can change the setting in the rocess. You can also set the BeoSound 9000 to show the clock eranently, even when the syste is in stand-by. Using the built-in clock When you want to ake BeoSound 9000 dislay the correct tie and be able to use the different Tier functions, you ust first set the built-in clock. CLOCK CLOCK? CLOCK Press to access the builtin clock Press to set tie, date or year Press to accet the changes and reveal the next dislay reeat this setting rocedure for date and year When you have set or changed the year, the dislay reads CLOCK? Press to store your new clock setting Press to show the tie When setting the clock, the dislay shows the tie, date and year for your settings. It has a 24 hour clock and it shows JAN for January FEB for February MAR for March APR for Aril MAY for May JUN for June JUL for July AUG for August SEP for Seteber OCT for October NOV for Noveber DEC for Deceber CLOCK Press to see the date and year To dislay the tie eranently CLOCK Press when Date and Year is dislayed, to change the dislay to 14:40 ON tie and ON e.g. 14:40 ON The tie dislay will be interruted by the essages which follow other functions or oerations, but it will return to dislaying the tie. CLOCK 14:41 OFF Press again to cancel the eranent showing of the clock e.g. 14:41 OFF. If you should ake a istake or change your ind while you are setting the clock, just ress CHECK and start over.

14 Start or sto at a secific tie You can ake BeoSound 9000 start or sto laying at designated ties through out the day and week. The BeoSound 9000 can store u to 15 such Tier settings and you can use it to e.g. wake you in the orning to your favourite CD or radio station. If, for exale, you want the BeoSound 9000 to sto laying at a secific tie in the evening, sily set a Tier with STANDBY as the source. When you set a Tier for Monday, Tuesday and Thursday, the Tier will be executed on these days, every week. If you use the BeoSound 9000 in a fully integrated Bang & Olufsen setu (see Use BeoSound 9000 with a video syste), you have to set the Tier function to ON or OFF via the TV. The dislay on the BeoSound 9000 will read TV OPERATED. Set a Tier For a Tier stand-by setting all the BeoSound 9000 needs to know, is the tie you want it to sto laying, and how often. As soon as you choose a stand-by Tier, a dislay will rot you to choose when the Tier should sto. TIMER Press to start rograing settings Press to choose a source for your Tier or choose a Tier stand-by Press to accet the source Then rogra when you want the Tier to start and sto Press reeatedly until you have found the exact tie for starting a Tier lay Press to accet Start Tier Reeat the rocedure with the and buttons to rogra the exact tie for stoing a Tier. When you rogra a Tier for your available sources, you will have to choose the station/channel where you want to rogra a Tier lay. When you choose a station for RADIO, the station you listened to last will aear. For TV and SAT channel 1 will aear as your first otion. Fro your available broadcasted sources e.g. TV and RADIO, you can only choose stations/ channels that have already been stored. Using your Beo4 reote control > Press the red button for ore than 1.5 sec. until the dislay reads TIMER? > Press GO to continue. Use the GO button, the buttons and and the nuber buttons 0 9 during the tiing rocedure to see otions and select between these. If you should change your ind while you are setting a Tier, sily ress a source button, CD or Radio, to exit the Tier rograing function. While you are setting a Tier, ressing the CHECK button will take you back one ste in the sequence.

15 Set a Tier for single date When you want to rogra a Tier for a single date, you ust choose the Single date otion in the Tier enu. Set a weekly Tier When you want to rogra a weekly Tier as a Tier lay or Tier stand-by, you ust choose the Days otion in the Tier enu. If you choose DAYS, the dislay will rot you to fill in the weekdays on which you want the syste to carry out the Tier. Choose the single date Choose the Days otion When you set the BeoSound 9000 to carry out a otion fro the enu, fro the enu, in the Tier on forthcoing, selected weekdays, these SINGLE DATE? in the dislay SINGLE DAYS? dislay DAYS? aears days are resented as abbreviations: DATE? aears MON for Monday Press to access a dislay TUE for Tuesday Press to dislay the date where you can fill in the WED for Wednesday you want to rogra a days you want to THU for Thursday Tier for rogra the Tier for FRI for Friday SAT for Saturday DATE 15 NOV? The dislay shows the Press to include a SUN for Sunday date FRI? M_WT weekday Press to accet the Press to exclude a selection weekday Press to store your? M_WTF_S When you have gone Tier rograing and through the whole return to noral source week the dislay will oerations rot you to store your Tier entry TIMER STORED The dislay shows that you have stored the Press to store your settings Tier entry If you choose SINGLE DATE, the cue DATE and today s date in the dislay rots you to choose a date within the next year. TIMER STORED The dislay shows that you have stored the settings The dislay for weekly rograing entails the first letters of the days you acceted (M, T, W, T, F, S, S) and underscores (_) for the days you did not choose. NOTE! The list of sources shown in the dislay contains N.MUSIC (for usic tracks stored on your PC) and N.RADIO (for radio sites on the Internet). These sources are available if you have connected your BeoSound 9000 to BeoLink PC 2 and have access to the Internet.

16 >>Start or sto at a secific tie Checking or clearing Tiers You can look u each Tier rograing entry to check its contents or cancel it coletely. CHECK Press to check your Tiers? Press to see Tier rograing nuber and source for the individual Tier entries Press reeatedly to dislay the details of a articular rograing When the dislay reads? The first dislay shows Tier entries in nuerical order with source and station nuber, the second shows the indication of tie for starting and stoing, and the third dislays the days for which the Tier is set. This is an on-off rograing. In all three instances, clearing of the settings is ossible. NEXT? Press to dislay NEXT? to see your next Tier rograing entry NO MORE Press to see your next entry If there are no ore entries, NO MORE, will aear in the dislay CLEAR CLEARED Press clear while inforation regarding a Tier rograing is dislayed in the dislay CLEARED will aear on the dislay

17 Switching the Tier function on or off The Tiers you have rograed into the BeoSound 9000 can all be executed with or without activating the loudseakers which are either directly connected to the BeoSound 9000 or are connected to it via BeoLink. The Tier ON/OFF function deterines whether a Tier Play can be heard on the loudseakers. ON/OFF Press to cut in or ress again to cut out the loudseakers Choose location for the Tier function In order to hear your Tier lay rograings, you ust activate the loudseakers in the roo or roos where you want usic by switching the Tier function to ON. If you set the Tier function to OFF, your seakers will be uted. If you therefore choose to set the seakers next to your BeoSound 9000 to OFF, but set your extra seakers in your bedroo to ON, the Tier lay will be carried out, and you will hear it through your extra seakers in your bedroo. However, if all Tier functions for the seakers connected to the BeoSound 9000 as well as on all your connected systes are set to OFF, a Tier will not be activated. TIMER ON TIMER OFF When you first ress ON/OFF, TIMER ON or TIMER OFF will aear in the dislay, according to the setting you have reviously ade

18 Playing CDs When you have loaded your BeoSound 9000 with 1 6 CDs, you are ready to start laying your CDs. When you ress the CD button to start laying, the CD where the carriage is situated will start laying fro the beginning. You can easily change between the different CDs and the individual tracks, to achieve the sequence of tracks you refer. When your first CD has finished laying, the carriage autoatically oves to the next CD you have loaded and starts laying this new CD. If you choose to hear another source, the CD layer switches off auto a tically. Loading CDs When you want to have access to load or reove your CDs, sily use the load button on the front of BeoSound 9000. Press to raise the glass door Press to lower the glass door CD Press to lower the door and start laying If you leave the glass door oen, it will close autoatically after 5 inutes. If BeoSound 9000 is left aused or stoed for ore than 30 inutes, it autoatically switches to stand-by. If the glass door is oen and the carriage is laced over a CD you want to reove, sily ove the carriage to another osition by ressing the direct CD selection button in front of a coartent. The CD ust be loaded with the text side facing you. Hold the CD by its edges and insert the CD (to section). To unload the CD, hold it by its edges and ush the CD slightly forward to release it. The carriage registers whether the CD coart ents you ask for are ety or not, and until the glass door is oened again, it will reeber the state of the coartents.

19 CD layback When you want to lay a secific CD, sily ress the direct CD selection button* laced next to the CD coartent. The carriage then oves to the CD you have chosen, and layback starts. CD Press to lay a CD Press to lay the next track on a CD Press to lay the sae track again or ress twice to lay the revious track When you are using your BeoSound 9000 CD layer, a tiny red indicator is lit beside all the occuied coartents. If, for exale, you choose a sequence of discs to be layed, only the indicators next to the CDs you have chosen will be lit, even though you have loaded six CDs. PAUSE Press to ause layback CD Press to resue laying VOL r Press to raise the volue VOL u Press to lower the volue MUTE Press to silence the seakers MUTE Press again to recall the sound Press to switch to stand-by *The CD selection buttons can also be used to ste through the tracks of your CDs. Press the button once and you select the CD, ress it continuosly and you ste through the tracks of the chosen CD.

20 Playing CDs in different ways Make BeoSound 9000 lay your favourite CDs in the articular sequence you want, or lay your CDs in rando order to vary your listening exerience. Every tie a CD is included in a sequence, the red indicator next to the CD coartent lights u. You can choose to cobine the RANDOM function with the EDIT function and lay your favourite tracks in a rando order. You can also cobine these two functions with SELECT and choose to lay only your favourite tracks fro for instance two CDs in rando order. Refer to Playing favourite CD tracks for further inforation about the EDIT function. Choosing a sequence of discs The select otion allows you to choose a secific sequence of CDs you wish to listen to. The CDs you have chosen will start laying in nuerical order. CD Press to start layback of a CD SELECT Press to ake SELECT SELECT DISC DISC aear Press the direct CD selection buttons next to the CDs you want to include SELECT Press to start clearing a sequence and lay all six CDs CLEAR Press to clear the sequence Playing CDs and tracks in rando order The rando lay function lays CDs and tracks on individual CDs in a rando order. Also chosen CDs and track series can be layed in rando order. CD Press to start laying a CD RANDOM Press to dislay RANDOM ON RANDOM ON and cut in the rando lay function RANDOM Press twice to dislay RANDOM OFF RANDOM OFF and cancel the rando lay function To leave out a CD you have included in the sequence SELECT Press to be able to reove a CD*, and ress the direct CD selection button next to the CD you want to reove To listen to a CD you have not included in your disc sequence, sily ress the direct CD selection button next to the CD you want to hear, and layback will start iediately. *NOTE! The SELECT otion lasts for 25 seconds fro when you ressed SELECT. If you ress a direct selection button after the SELECT otion has ended, the disc you chose will start layback iediately and override your sequence. When it has finished laying, BeoSound 9000 will continue laying the sequence you chose before.

Playing favourite CD tracks 21 The edit function enables you to rogra series of tracks for your individual CDs and store the eranently. Editing a CD eans that you include or exclude each track on the CD while scanning it as described to the right. Select and store a series of tracks Before aking your own series of tracks you ust start laying the CD. Enable or disable layback of a track series Whenever you load an edited CD, only the selected tracks will be layed. These are layed in nuerical order. However, you can choose to listen to the entire CD. You can also delete the series of tracks you have ade, to always lay the CD in full. The first 15 seconds of each track on the CD will be layed. On the dislay CD Press to lay CD CD Press to lay a CD the track nuber you are currently laying will aear. During this 15- second layback, you ust include EDITING EDITING? Press to scan the CD EDITING? aears on the dislay EDIT Press to start edited layback the articular track into the series or exclude the track. As soon as you ress either button, the next track on the CD starts laying*. Press to start scanning the tracks Press to include a track EDIT ON EDIT EDIT OFF EDIT ON aears Press twice to lay a CD in full and cancel EDIT EDIT OFF aears nuber in the series, or If you cancel the edit function while an edited CD is laying, all tracks beyond the current track Press to exclude a nuber will be layed. The EDIT function reains track nuber fro the ON until you cancel it even in stand-by. series EDITING EDITING aears when you have included or excluded the last track Press to accet the track series To clear a track series Choose the CD which track series you want to clear EDITING Press to access the rograing otion CLEAR Press to clear the track series altogether *NOTE! If you do not choose whether you want to include or exclude a track within the 15 second layback, the CD layer will include the track autoatically. If you choose to leave EDITING before you have scanned, acceted or excluded all the tracks on the CD, the reaining tracks will be regarded as excluded fro the track series.

22 Nae your CDs To distinguish between your individual CDs, you can nae the. The nae will then be shown in the dislay when you load the CD. You can store a total of 200 naes in your BeoSound 9000. Each nae ay contain u to 12 characters, including nubers. If you have not given a nae to the CD, the track nuber, track tie or elased tie will aear in the dislay instead. You can access a list of CD naes in the dislay. Nae a CD The CD you are naing ust be laying in the BeoSound 9000. If the CD has already been naed, you can change the nae or delete it, or you can just leave the function by ressing CD. CD NAMING A CD Press to lay CD Press to access the naing function. A is blinking in the first character osition Press to reveal the characters one by one Press to ove to the next character, ress reeatedly to store the nae, or Press while you are naing CDs or track series in order to autoatically store the nae and exit the naing function See the list of CD naes When the list is dislayed, you can delete the naes and any stored series of tracks at the sae tie. CD Press to lay CD NAMING Press to access the CD LIST naing list, CD LIST GLENN MILLER aears briefly, then the nae of the current CD aears, for exale GLENN MILLER Press to list the naes one by one and return to naes further u the list CLEAR Press to clear a nae while the aroriate nae is dislayed CD Press to return to noral source oeration To clear a nae > Press NAMING to access the naing function. > Press CLEAR to clear the nae. > Press CD to return to noral source oeration. The naing function can also be accessed fro your Beo4 reote control > Press the blue button for ore than 1.5 sec. to call u NAMING? in the dislay. > Press GO and use the and buttons to select characters. > When you have finished, ress and hold the GO button to ove to the storing level. > Press GO to accet and EXIT to leave the CD naing rocedure. If the carriage is situated on a CD which has been given a nae or the CD has been edited, the nae or nuber of this CD will aear in the dislay when you access the list. If the CD under the carriage is unknown, the CD list will aear in the dislay and you have to ress the or buttons to get a nae or nuber dislayed. If you attet to nae or rogra track series for ore than 200 CDs the dislay will read CD LIST FULL, and you will have to clear an entry before you can add another. NOTE! It is only ossible to nae CDs with the Beo4 reote control if your BeoSound 9000 is in Otion 1, refer to age 33 for further inforation about Otion settings.

Positioning CDs 23 For your aesthetic enjoyent you can osition your individual CD to ake the grahical design and text on the CD resent itself to your satisfaction. When you store a osition for each CD, the BeoSound 9000 will reeber these ositions. No atter how any ties you reove and reload the CDs, the individual CDs will be returned to these ositions every tie they sto turning*. Load and adjust a CD anually When you have loaded a CD, you adjust the osition of the CD anually. Then you ove the carriage to this articular CD and access the ositioning function for CDs in order to store the osition you have chosen. Press the direct CD selection button next to the CD to ove the carriage SELECT Press to select the CD you want to osition SELECT Press to save the osition for the CD while it is laying POSITION? POSITION? aears Clear the ositioning If you want to clear the osition for a CD, ove the carriage to the CD in question. SELECT Press to select the CD you want to clear SELECT Press to access the ositioning function to clear the osition CLEAR Press to clear the osition Press to store the osition you chose for the CD when it was loaded Reeat this rocedure for all the CDs you have loaded *NOTE! Soe CDs do not contain the inforation required by the BeoSound 9000 in order to store ositions for CDs. Therefore, you ay exerience that the osition you have stored for a CD is not adhered to by the BeoSound 9000. You will, of course, still be able to lay the CD in question.

24 Dislay CD inforation The BeoSound 9000 dislay can give you three different tyes of inforation about the CD being layed: Nae* Nuber of CD and track Nuber of CD and elased track tie Switching between dislays Your chosen dislay indication for the CD layer will reain in the dislay anel and only disaear teorarily when you undertake another oeration on the BeoSound 9000 oeration anel. Then the inforation which accoanies this oeration will aear in the dislay for a short eriod of tie. To switch fro one dislay to the other, you ust ress the button reeatedly while the CD is laying. CD Press to lay a CD Press reeatedly to change the CD dislay indication The dislays show the nae of the CD, the nuber and track nuber of the CD, and the nuber of the CD along with the elased tie of the current track in inutes and seconds. *NOTE! You have to nae the CD before a nae aears in the dislay, lease refer to Nae your CDs for further inforation about naing.

Playing other sources 25 Connecting extra equient to your BeoSound 9000 enables you to listen to the sound of an external source through the seakers connected to your BeoSound 9000. However, all control oerations ust be carried out on the extra equient you connect. Listen to external sources While you are laying an external source through your BeoSound 9000, you can still use the functions which relate to sound, lease refer to the chater Adjust and store sound settings. If you are recording fro the BeoSound 9000 onto Audio tae, you will not be able to listen to another source, CD or radio, other than the one you are recording. If you change source while recording, you will then record this new source onto your Audio tae. You can record the source, CD or radio, you are laying on the BeoSound 9000 via the AUX-socket onto Audio tae or another available edia. The recording function ust be carried out via the controls of the extra equient. A.AUX VOL r VOL u Press to select extra equient Press to raise the volue Press to lower the volue MUTE Press to silence the seakers iediately Press again to recall the sound Extra equient ust be connected to the AUXsocket on the back of the BeoSound 9000. You will be able to record digital signals fro the BeoSound 9000 to a Digital Audio Recorder via the digital outut socket. Please refer to Connect the cables for further inforation. Connect Headhones to the socket laced in a low osition on the side of the BeoSound 9000 cabinet. NOTE!: Please contact you Bang & Olufsen retailer for colete inforation about which Bang & Olufsen or non-bang & Olufsen roducts can be used with the BeoSound 9000.

26 Using the radio To be able to use the radio, you ust first tune in to the radio stations you want to store and then store the on rograe nubers of their own. You can change the rograe nuber of your radio station any tie also without being in the rocess of tuning. You can store u to 60 radio stations and if you like, you can give the a short nae which you choose yourself. Please refer to Nae radio stations for further inforation. Presetting radio stations Letting the BeoSound 9000 tune in your radio stations, ensures that you get all available stations. Once you have found a radio station, you can fine tune it, if the recetion is oor. RADIO Press to turn on the radio TUNE Press to start the tuning function AM/FM Press to select AM or FM, switches fro one to the other, check dislay for an indication of which one you have chosen Clearing resets If you want to cancel one of your radio resets, you can do so using the CLEAR function. RADIO Press to turn on the radio Press to search for a rograe nuber CLEAR Press to clear the rograe Press to confir the clearing of the radio rograe Press to search for a CLEARED CLEARED will aear in radio station u or the dislay down the frequency band Press to accet the station you have found P.NO. Press to change the dislayed rograe nuber Press to select a rograe nuber u or down Press to store your new STORED radio rograe STORED aears in the dislay If a station needs fine tuning, or you wish to switch between ono and stereo sound on radio rogras, lease see Otiise radio sound.

Otiise radio sound 27 If a radio station is not tuned in clearly enough, it ay be because the rograe needs to be fine tuned. You can also choose to alter the sound to your satisfaction by choosing between ono or stereo recetion. Fine tuning a radio station The fine tuning function enables you to ove slowly through the frequencies, or to detune a rograe slightly because of noisy recetion. Mono/stereo recetion Your BeoSound 9000 autoatically switches to ono if the stereo signal is not strong enough to roduce an accetable stereo sound. You can overrule this autoatic function if you wish and select ono anually. RADIO Press to turn on the RADIO Press to turn on the radio rograe you relevant radio station want to fine tune TUNE Press to select the RADIO 11 The nuber of the last tuning function and layed radio rograe ress reeatedly until is dislayed, e.g. 11 you have reached the settings for ono/ TUNE Press to ake the stereo recetion P11 88.4 frequency aear in the dislay, e.g. 88.4 STEREO? The dislay shows the MONO? choices TUNE Press to access the fine tuning function Press to select between the ono or stereo FINE 88.4 The dislay indicates setting that you can now fine tune the station Press to store your new tuning on the Press to fine tune the rograe nuber station towards a higher or lower frequency Press to accet the fine tuned station Press again to store station and rograe nuber Once you have fine tuned the station, you can choose a different rograe nuber if you like before you store it. Please refer to Presetting radio stations for further inforation.

28 Nae radio stations You can nae all the radio stations you have stored. Choosing a nae is coletely u to you. If you haen to ake a istake or change your ind while you are naing a radio station, sily ress the NAMING button again and start over. Naing radio stations Naing your radio stations can hel you reeber a station not only by its nuber but by a articular nae. When you are listening to a radio station, its nae will aear in the dislay*. Once you have coleted entering a nae, you store the nae and it will then aear every tie you choose this station again. Clear a nae If you have left the naing function and want to clear the nae, return to the naing function and clear the nae. If you do not nae your stations, the station s own nae ay aear instead, rovided such a nae is being transitted by the radio station itself*. If you want to clear the nae after you have keyed it in, ress CLEAR RADIO Press to turn on the radio station you want NAMING Press to access the naing function instead of and the nae you have keyed in will be erased. NAMING A to nae Press to start the naing function. The first of the CLEAR Press to clear the nae twelve character ositions blinks, indicating that you can start entering a nae Press to reveal the characters one by one Press to reveal reviously shown characters Press to ove to the next character osition Press to store the nae of the radio station NAMING NAMING will aear in the dislay RADIO Press to store he nae and exit the naing function You can ress RADIO at any tie to store and exit the naing function *NOTE! Such a nae can only be transitted if your BeoSound 9000 is equied with the RDS facility. The RDS facility is not a standard feature in all BeoSound 9000, but it will be available as an otional extra.

Playing your radio stations 29 Having tuned in the radio stations you want, as shown on the revious ages, you are ready to listen to the radio. Playing radio When you turn on the radio, the station you were last listening to starts laying, and it will be indicated in the dislay, which radio station is laying. If you have given a nae to the radio station, the dislay will read out that nae. Switching between dislays The dislay can give you four different tyes of inforation about the radio station you are listening to: Station nae or RDS*, station nuber and radio frequency. The inforation you have chosen to dislay will reain on the BeoSound 9000 dislay until you choose another of the dislays illustrated below. RADIO Press to turn on the RADIO Press to turn on the radio radio Press to ste through Press reeatedly to your radio stations change the radio dislay indication, to show Press to switch to standby CLASSIC Station nae indication RADIO 5 Prograe nuber indication P5 FM 89.9 Radio frequency indication

30 Adjust and store sound settings All sound levels are set to neutral values fro the factory, but you can ake your own sound adjustents and store the. Sound adjustents If you wish to alter the settings for sound, sily access the relevant function, ake your adjustents and store the new setting. The treble and bass levels can be raised or lowered as you like and you can alter the balance, i.e. the distribution of sound eerging fro TREBLE Press to access the treble adjustent function the loudseakers to suit your listening BASS Press to access the bass osition. adjustent function The BeoSound 9000 also features a loudness function which you can activate or deactivate as you like. The loudness function akes the usic ore dynaic. It coensates for the huan ear s lack of sensitivity to high and low frequencies when BALANCE Press to access the balance adjustent Press to raise or lower the treble or bass levels; or adjust the balance between the left and right seaker The first four dislays are exales of levels that the different sound functions can be set to. Volue can be adjusted in stes of two within a range of 00 to 72, treble and bass levels can be adjusted within a range of -4 to +4 and the balance setting (here neutral) can be adjusted within a range of 8 to either side. The fifth exale is a dislay, which shows the setting for the loudness function listening to low usic. You can reset the sound levels to their original settings at any tie. If you change your ind and do not wish to store your adjustents, sily LOUDNESS LOUDNESS ON LOUDNESS OFF Press to see the status of the loudness adjustent function LOUDNESS ON or LOUDNESS OFF Press LOUDNESS again to change the setting ON if loudness is switched on, and OFF if loudness is switched off. The SOUND? dislay rots you to store the current sound setting. ress a source button on the BeoSound 9000 control anel. SOUND? Press to accet all sound levels SOUND Stored sound settings aly each tie you switch on BeoSound 9000.? aears on the dislay Press to store all sound levels If you have not stored your sound adjustents RESET Press to reset the sound levels to their reviously stored settings NOTE! When BeoSound 9000 is used in a fully integrated setu (see Use BeoSound 9000 with a video syste), sound ust be adjusted as described in the guide for your video syste. The dislay on the BeoSound 9000 will read TV OPERATED.

Using the Beo4 reote control 31 The BeoSound 9000 CD layer is oerated fro a distance via the Beo4 reote control. The Beo4 reote control oerates all the riary functions in the BeoSound 9000 such as turning on RADIO Press to switch on the radio the radio or the CD layer, changing radio stations, CD tracks or CDs. It CD Press to switch on the CD layer also selects stations or CDs to be layed, adjusts sound functions, auses layback and finally switches to stand-by. TV LIGHT RADIO SAT DVD CD V TAPE RECORD A TAPE Ste through your radio stations, or tracks on a CD. Press when RANDOM is shown in the dislay, to activate the function, and ress to switch it off when the function is dislayed The Beo4 reote control enables you to select secific tracks on CDs, select sequences of secific discs to be 7 8 9 4 5 6 1 2 3 0 9 Use the nuber buttons to key in a radio station nuber or CD nuber. To select a track, ress LIST until TRACK is shown in the dislay*, then use the nuber buttons to key in the track nuber layed, search forward and backward on CDs, switch on the rando order TEXT 0 MENU l n Press to change to the revious or following CD layback and edited order layback STOP Press to ause layback any tie functions as well as it selects extra equient. GO GO Press to resue layback The GO button equals on the BeoSound 9000 oeration anel LIST EXIT LIST RANDOM Press to dislay extra buttons or functions*, e.g. RANDOM STOP GO Press to activate the source or function in the Beo4 dislay r To turn the volue u or down, ress in the u iddle to ute seakers, ress again to recall sound Switch the BeoSound 9000 to stand-by *NOTE! In order to dislay the relevant extra buttons on the Beo4, you ust add the to the Beo4 list of functions. Please refer to Beo4 s own User s Guide for inforation about how to add extra buttons to the Beo4.

32 Use BeoSound 9000 with a video syste To use the BeoSound 9000 together with a Bang & Olufsen video syste they ust be connected by a Master Link cable, this is a so-called Audio/ Video (AV) integrated setu. If you choose to interconnect your Bang & Olufsen roducts, you can distribute the sound fro your sources throughout your hoe. Many different setus are available, lease contact a Bang & Olufsen retailer for further inforation. Otion rograing is a rerequisite for integrated setus. It is not necessary if BeoSound 9000 is only connected to seakers! Using BeoSound 9000 with a video syste also requires that you use a Beo4 reote control. Refer to Using the Beo4 reote control, or the Beo4 s own User s guide. A fully integrated setu When BeoSound 9000 is used in a fully integrated setu, the seakers are connected to the video syste, and the video syste takes over soe of the functions entioned in this guide. Furtherore, all reote control oerations (audio and video) ust be directed to the video syste. Please refer to the guide for the video syste, for further inforation. To lay a source in the AV syste CD Press a source button RADIO on the Beo4, e.g. CD, TV RADIO, TV, etc. Siulcast radio/tv transissions to watch a TV channel while listening to the sound fro a radio station TV Press to switch on the TV LIST Press reeatedly until AV AV* aears in the Beo4 dislay RADIO Press to switch on the radio and start siulcast transission An AV integrated setu In an AV integrated setu, a air of active seakers are connected to the BeoSound 9000. You can hear any source you like in the loudseakers of either syste. The BeoSound 9000 and the video syste do not have to be laced in the sae roo. To lay TV, video or satellite sound on the BeoSound seakers LIST Press until AV* aears AV in the Beo4 dislay TV Press to hear TV sound, V TAPE video sound, or a SAT satellite TV/radio rogra To lay the radio or CD on the TV seakers LIST Press until AV* aears AV in the Beo4 dislay RADIO Press to hear radio sound, or CD ress to hear a CD *NOTE! In order to dislay AV on the Beo4, you ust add it to the list of functions. Please refer to the Beo4 s own User s guide for inforation on how to add functions to the Beo4.

33 Otion rograing For BeoSound 9000 to be art of an AV setu, you ust ake sure it is set u to function with the other roducts you have connected. This eans that you ust rogra the BeoSound 9000 to the correct otion. Otion 2 Otion 0 BeoSound 9000 has five different otion settings: Otion 0. Used in a one-roo AV setu. This Otion is selected autoatically if no seakers (or headhones) are connected directly to the BeoSound 9000. Otion 1 (factory setting). Used when the BeoSound 9000 is used on its own, or when it is connected to active seakers in an AV integrated setu. Otion 2. Used when the BeoSound 9000 is set u in one roo and connected to a video syste set u in another roo. Otion 5. Used when the BeoSound 9000 is set u in a link roo which also corises a Bang & Olufsen television. Otion 6. Used when the BeoSound 9000 is set u in a link roo without a Bang & Olufsen television. Switch your entire Bang & Olufsen syste to stand-by, and then (using the Beo4 reote control): > Hold the button while ressing LIST. > When the Beo4 dislay reads OPTION?, ress GO. > Press LIST to dislay A.OPT and then key in the aroriate nuber (0, 1, 2, 5 or 6). In a fully integrated syste, your BeoSound 9000 acts as a ere audio source. The sound is reroduced through the seakers in the BeoVision TV or, as shown here, through a set of active seakers connected to the TV. Otion 1 Otion 1 In a one-roo AV integrated setu, a air of active seakers has been connected to the BeoSound 9000. Otion 2 Otion 2 In a two-roo AV integrated setu, your BeoSound 9000 has been set u with a set of active seakers in one roo, and the video syste in another.

34 Looking after BeoSound 9000 Noral aintenance, such as cleaning the BeoSound 9000, is the resonsibility of the user. To achieve the best result, lease follow the instructions. Do not use alcohol or other solvents to clean any art of BeoSound 9000! Surfaces Before you start cleaning BeoSound 9000, we recoend that you oen the glass door and then switch off the ains. In this way all surfaces are accessible for cleaning. Use a soft, dry cloth to wie dust off the BeoSound 9000. To clean the surfaces, we recoend that you use a ild window cleaner. A CD echanis The circuit controlling the oveent of the CD carriage has a built-in safety function which rotects your fingers, etc. fro being hit by the fast oving carriage. This circuit deends on light/reflections, and works via oto-couling devices built into the two sall egs (A). When the glass door is oened, or if soething interruts the light-circuit, the carriage slows down in seed, and finally coes to a halt. Over tie dust ay build u and thus reduce the light eitted to and fro the oto-couling devices. Dust articles on the inside of the glass door ay also cause extraordinary reflections which ay be interreted by the safety function in a wrong way. A So, in order to revent alfunction of the safety circuit, we recoend that you wie dust off the two egs (A) on a regular basis. Likewise, when cleaning the surfaces of BeoSound 9000, reeber also to clean the inner surface of the glass door. NOTE! Treat the glass door with great care! If it cracks or chis, or if it is daaged in any other way, it ust be relaced iediately as it could otherwise cause great bodily har. If the glass door should need to be relaced, lease contact your Bang & Olufsen retailer.

35 Handling your CDs If dust builds u in the oto-couling devices, the CD carriage will slow down, and the cue CLEANING REQUIRED aears in the BeoSound 9000 dislay. When the cue aears you ust: > Switch off the BeoSound 9000. > Wie dust off the two egs (A). > Clean the inner surface of the glass door. > Switch BeoSound 9000 on again. IMPORTANT! If you exerience any robles when trying to lay a articular CD always check it for faults (scratches, fingerrints, dust or dirt, etc.). Dust ay build u on the CDs, esecially if you leave the sitting in the BeoSound 9000 for a long tie. If there are no visible faults on the CD, lease contact your Bang & Olufsen retailer. Do not attet to clean the otics of the CD echanis yourself this ust be done by a qualified technician only! We do not recoend using secial cleaning CDs in BeoSound 9000!

36 The PIN-code syste You can rotect your BeoSound 9000 by entering a four-digit PIN (Personal Identification Nuber) code. Should your BeoSound 9000 be disconnected fro the ains for ore than 30 inutes, only those who know your PIN-code can gain access to your BeoSound 9000. If the PIN-code is not entered, the BeoSound 9000 autoatically switches to standby after 3 inutes. To activate the PIN-code syste, to change your code or to delete it altogether, your BeoSound 9000 ust be in stand-by ode. If you should lose or forget your code, contact your Bang & Olufsen retailer for a aster code that disables your PIN-code and gives you access to your BeoSound 9000. Activate the PIN-code syste While the BeoSound 9000 is in stand-by ode you can set u the PIN-code. Press twice followed by PAUSE to activate PAUSE the PIN-code function. NEW PIN The dislay shows NEW PIN for 1.5 sec. PIN then you can enter a PIN-code Press to select a digit* Press to accet the digit The digit is relaced by a and the next underscore blinks. Continue to enter the last three digits in the sae anner. If you wish to change the entered digits RESET Press to start entering fro the beginning When the PIN-code has been entered Press to accet the PINcode. The dislay shows CONFIRM CONFIRM for 1.5 sec. Change or delete your PIN-code While the PIN-code function is turned on you can always ake changes to the PIN-code. Press twice followed by PAUSE to activate PAUSE the PIN-code function PIN Enter the current PINcode. NEW PIN? The dislay shows NEW PIN? Press to choose fro the two otions NEW PIN? NEW PIN? or PIN OFF? PIN OFF? Select NEW PIN? to change your PIN-code PIN Enter the new PIN-code Press to accet the new CONFIRM PIN-code. The dislay shows CONFIRM for 1.5 sec. PIN then re-enter the new PIN-code Press to confir the new PIN-code PIN STORED then re-enter the PINcode Press to confir the PINcode The dislay shows that your setting is stored STORED The dislay shows that your new PIN-code is stored Select PIN OFF? to delete your PIN-code DELETED The PIN-code function is disabled and the dislay shows DELETED for 3 sec. If an incorrect code is entered the second tie you ust set u the PIN-code fro the beginning. For security reasons it is only ossible to change or verify the PIN-code five ties within a eriod of 3 hours. If an incorrect code is entered five ties, BeoSound 9000 is turned off, and ust be left in stand-by ode for 3 hours, before you ay try again. *NOTE! It is also ossible to enter the digits using the nuber keys 0 9 on your Beo4 reote control.

37 Using your PIN-code When a PIN-code has been rograed, and the BeoSound 9000 has been disconnected fro the ains for ore than 30 inutes, you ust enter the PIN-code when the BeoSound 9000 is turned back on. Did you forget your PIN-code? Should you forget your PIN-code you can require a five-digit Master Code fro your Bang & Olufsen retailer. PIN Enter the PIN-code Press to select a digit When you have received a Master Code PIN When the dislay is oen for PIN-code inut Press to accet the digit RADIO 1 When the PIN-code has been entered the dislay returns to the relevant source dislay e.g. RADIO 1 If an incorrect PIN-code is entered the dislay will show ERROR and you ay try again. After the fifth try, the BeoSound 9000 is turned off, and ust be left in stand-by ode for 3 hours, before you can try again. PIN PIN DELETED Press the button for ore than 3 seconds to change the dislay to fit 5 digits Enter the Master Code Press to select a digit Press to accet the digit The dislay shows that the PIN-code lock is off When the Master Code is entered, the BeoSound 9000 can be used without entering the code again.

38 For your inforation Your needs as a user are given careful consideration during the design and develoent rocess of a Bang & Olufsen roduct and we strive to ake our roducts easy and cofortable to oerate. Therefore, we hoe that you will take the tie to tell us about your exerience with your Bang & Olufsen roduct. Anything which you consider iortant ositive or negative ay hel us in our efforts to refine our roducts. Thank you! Write to: Bang & Olufsen a/s Consuer Service det. 7210 Peter Bangs Vej 15 DK 7600 Struer or fax: Bang & Olufsen Consuer Service +45 97 85 39 11 (fax.) or e-ail: beoinfo1@bang-olufsen.dk Visit our Web-site on www.bang-olufsen.co 3507491 0505 Printed in Denark by Bogtrykkergården a-s, Struer

NOTE: This equient has been tested and found to coly with the liits for a class B digital device, ursuant to art 15 of the FCC Rules. These liits are designed to rovide reasonable rotection against harful interference in a residential installation. This equient generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, ay cause harful interference to radio counications. However, there is no guarantee that interference will not occur in a articular installation. If this equient does cause harful interference to radio or television recetion, which can be deterined by turning the equient off and on, the user is encouraged to try to correct the interference by one or ore of the following easures: Reorient or relocate the receiving antenna. Increase the searation between the equient and receiver. Connect the equient into an outlet on a circuit different fro that to which the receiver is connected. Consult the retailer or an exerienced radio/tv technician for hel. This roduct fulfils the conditions stated in the EEU directives 89/336 and 73/23. CLASS 1 LASER PRODUCT The black and yellow label on the coact disc layer serves as a warning that the aaratus contains a laser syste and is classified as a class 1 laser roduct. In case any difficulties arise with the coact disc layer, lease contact a Bang & Olufsen retailer. The aaratus ust be oened by qualified service ersonnel only. CAUTION: The use of any controls, adjustents or rocedures other than those secified herein ay result in hazardous radiation exosure. This class B digital aaratus eets all requireents of the Canadian Interference-Causing Equient Regulations.

www.bang-olufsen.co