Worldwide Contacts www.tycofire.com Preaction System with DV5 Deluge Valve Single Interlock, Supervised Wet Pilot Actuation /2 thru 8 Inch (DN thru DN200) General Description The DV5 Supervised Single Interlock Preaction System with Wet Pilot Actuation (Refer to Figure ) utilizes automatic sprinklers and a supplemental detection system. The supplemental detection system is comprised of wet pilot lines and pilot sprinklers. Actuation of the detection system automatically operates (releases) the DV5 Deluge Valve, allowing water to flow into the sprinkler piping system and to be discharged from any sprinklers that may be open. In accordance with the requirements of the National Fire Protection Association, a preaction system employing more than 20 automatic sprinklers is to have the sprinkler piping automatically supervised to monitor the overall integrity of the system. In the case of a Supervised Single Interlock Preaction System, a Riser Check Valve (that does not require the use of priming water) provides an air check so that the system can be automatically pressurized with a nominal supervisory air or nitrogen pressure of 0 psi (0,6 bar). A supervisory low pressure alarm switch that is set to transfer its contacts at nominally 5 psi (0, bar), on decreasing pressure, is utilized to indicate whether there are any abnormal leaks in the sprinkler system piping. Loss of air pressure from the system as a result of a damaged sprinkler or broken piping will not cause the DV5 Valve to open the air pressure is for supervisory alarm only. Typically, the system designer selects the detection components for a single interlock preaction system that will respond to a fire sooner than the automatic sprinklers. Consequently, the system will experience a minimal delay in water delivery over that for a wet pipe sprinkler system because the system will have essentially filled with water before a sprinkler operates. In the case of wet pilot actuation, the system designer selects wet pilot sprinklers that will operate sooner than the automatic sprinklers chosen for use on the sprinkler piping. Supervised single interlock preaction systems are generally used to protect areas where there is danger of serious water damage that might result from damaged automatic sprinklers or piping. Typically, such areas include computer rooms, storage areas for valuable artifacts, libraries, and archives. Single interlock preaction systems are also effectively used to protect properties where a prealarm of a possible fire condition may allow time for fire extinguishment by alternate suppression means, prior to a sprinkler discharge. In the event the fire cannot otherwise be extinguished, the preaction sprinkler system will then perform as the primary fire protection system. The DV5 Deluge Valve (described in Technical Data Sheet TFP305) is a diaphragm style valve that depends upon water pressure in the Diaphragm Chamber to hold the Diaphragm closed against the water supply pressure. When the DV5 Valve is set for service, the Diaphragm Chamber is pressurized through the trim connections from the inlet side of the system s main control valve, such as an O.S.&Y. gate valve or butterfly valve (Fig. ). Opening of a pilot sprinkler, releases water from the Diaphragm Chamber faster than it can be replenished through the /8 inch (3,2 mm) restriction provided by the Model ASV Automatic ShutOff Valve in the diaphragm supply connection (Item 5 Fig. 3A, also described in Technical Data Sheet TFP384). This results in a rapid pressure drop in the Diaphragm Chamber to below the valve trip point. The water supply pressure then forces the Diaphragm open, permitting water to flow into the system piping, as well as through the Alarm Port to actuate the system alarms. As water flows into the system, the pilot chamber of the Model ASV Automatic ShutOff Valve (Item 5 Fig. 3A) becomes pressurized and the ASV automatically shuts off the diaphragm chamber supply flow to the DV5 Diaphragm Chamber. Shutting off the diaphragm chamber supply flow prevents the DV5 Diaphragm Chamber from becoming repressurized, thereby preventing inadvertent closing of the DV5 during a fire (as may be the case if an actuation device other than a pilot sprinkler were to be closed after its initial operation, for example a remote manual control station). Continued on Page 4 Page of 4 JULY 204 TFP
TFP Page 2 of 4 6 5 3 5 4 8 3 4 2 6 2 3 4 5 6 8 DV5 Deluge Valve Main Control Valve (N.O.) Diaphragm Chamber Supply Control Valve (N.O.) Local Manual Control Station Automatic Sprinklers Wet Pilot Line Sprinklers (Fire Detection) Water Supply Pressure Gauge Diaphragm Chamber Pressure Gauge 0 2 3 4 5 System Drain Valve (N.C.) Main Drain Valve (N.C.) (Shown at Rear of Valve) Diaphragm Chamber Automatic ShutOff Valve Waterflow Pressure Alarm Switch (Shown at Rear of Valve) Water Motor Alarm (Optional) Riser Check Valve Supervisory Air Pressure Gauge 6 Automatic Supervisory Air/Nitrogen Supply Supervisory Low Pressure Alarm Switch FIGURE ( OF 2) SUPERVISED SINGLE INTERLOCK PREACTION SYSTEM WITH WET PILOT ACTUATION SYSTEM SEMATIC (FRONT VIEW)
TFP Page 3 of 4 6 5 3 4 2 6 3 0 2 2 3 4 5 6 DV5 Deluge Valve Main Control Valve (N.O.) Diaphragm Chamber Supply Control Valve (N.O.) Local Manual Control Station (Shown at Front of Valve) Automatic Sprinklers Wet Pilot Line Sprinklers (Fire Detection) Water Supply Pressure Gauge (Shown at Front of Valve) 8 0 2 3 4 5 Diaphragm Chamber Pressure Gauge (Shown at Front of Valve) System Drain Valve (N.C.) Main Drain Valve (N.C.) Diaphragm Chamber Automatic ShutOff Valve (Shown at Front of Valve) Waterflow Pressure Alarm Switch Water Motor Alarm (Optional) Riser Check Valve Supervisory Air Pressure Gauge (Shown at Front of Valve) 6 Automatic Supervisory Air/Nitrogen Supply Supervisory Low Pressure Alarm Switch FIGURE (2 OF 2) SUPERVISED SINGLE INTERLOCK PREACTION SYSTEM WITH WET PILOT ACTUATION SYSTEM SEMATIC (REAR VIEW)
TFP Page 4 of 4 WATERFLOW PRESSURE ALARM SWIT GROOVED COUPLING NOTICE The DV5 Supervised Single Interlock Preaction System with Wet Pilot Actuation Trim described herein must be installed and maintained in compliance with this document, as well as with the applicable standards of the National Fire Protection Association, in addition to the standards of any other authorities having jurisdiction. Failure to do so may impair the performance of the related devices. The owner is responsible for maintaining their fire protection system and devices in proper operating condition. Contact the installing contractor or product manufacturer with any questions. Technical Data Approvals UL and CUL Listed Deluge Valve DV5 Riser Check Valve Model CVFR LOW AIR PRESSURE ALARM SWIT ECK NOTE: /2 inch (DN) risers utilize a 2 inch (DN50) Model CVFR Riser Check Valve connected to the /2 inch (DN) DV5 Deluge Valve by a 2 x /2 inch Figure 6 Reducing Coupling. PREACTION SINGLE INTERLOCK WET PILOT ACTUATION TRIM DV5 DELUGE SYSTEM SHUTOFF. SEE FIGURE 3, PER SIZE AS APPLICABLE, FOR TRIM ARRANGEMENT WITH BILL OF MATERIALS AND COMPONENT PART NUMBERS. 2. TRIM SHOWN FULLY ASSEMBLED; COMPONENTS SU AS GAUGES AND SWITES MAY REQUIRE ASSEMBLY IN TRIM AT INSTALLATION. FIGURE 2 DV5 PRETRIMMED SUPERVISED SINGLE INTERLOCK PREACTION SYSTEM, WET PILOT ACTUATION Valve Trim The Supervised Single Interlock Preaction System with Wet Pilot Actuation Trim (Fig. 3A or 3B) forms a part of the laboratory listings and approvals. The trim is necessary for proper operation of the DV5 Valve. Each package of trim includes the following items: Water Supply Pressure Gauge Diaphragm Chamber Pressure Gauge Diaphragm Chamber Connections Manual Control Station Main Drain Valve System Drain Valve Alarm Test Valve Automatic Drain Valve System Air Pressure Gauge Air Supply Connections Low Air Pressure Supervisory Switch Waterflow Pressure Alarm Switch (PS02) The following items are included in the Pretrimmed Valve Assembly and can be ordered separately for the valve trim: Model BFVN Butterfly Valve Figure 5 Grooved Coupling To ease field assembly of the trim arrangement, the trim components are provided partially assembled as shown in Figure 3B. The trim arrangement is provided with galvanized or black nipples and fittings. The galvanized trim is intended for noncorrosive or corrosive conditions, whereas the black trim is principally intended for use with AFFF systems. NOTE: When the system pressure is greater than 5 psi (2, bar), provision is to be made to replace the standard order 300 psi (20, bar) Water Pressure Gauges, shown in Figure 3A or 3B with separately ordered 600 psi (4,4 bar) Water Pressure Gauges. Detection System In order for a single interlock preaction system to be hydraulically calculated as a wet pipe system, as opposed to a dry pipe sprinkler system, the detection system must be designed to operate sooner than the automatic sprinklers on the sprinkler piping. In the case of wet pilot actuation, the system designer selects pilot sprinklers that will operate sooner than the automatic sprinklers chosen for use on the sprinkler piping. The Supervised Single Interlock Preaction System with Wet Pilot Actuation Trim provides for connection of a detection system consisting of Wet Pilot Line Sprinklers (heat detectors) and manual control stations interconnected with minimum /2 inch (DN5) Schedule steel pipe. The pilot line is connected to the Wet Pilot Detection connection shown in Figure 3B. Nominal installation dimensions for the Supervised Single Interlock Preaction System with Wet Pilot Actuation Trim are shown in Figure 4. Wet pilot sprinklers are to be minimum 5.6 Kfactor orifice listed or approved automatic sprinklers. Manual Control Stations are to be the Model MC described in Technical Data Sheet TFP382. The maximum height of a wet pilot line above the DV5 Valve must not exceed the limitations shown in Table A as a function of the minimum water supply pressure to the DV5 Valve for an equivalent length (pipe plus fittings) of the pilot line up to 500 feet to the most remote pilot sprinkler. Provision must be made for installing a 5.6 Kfactor orifice, Inspector s Test Connection at the most hydraulically demanding location of a wet pilot line (usually adjacent to the highest and most remote wet pilot line sprinkler or manual control station). Continued on Page 0
TFP Page 5 of 4 NO. DESCRIPTION QTY. P/N NO. DESCRIPTION QTY. P/N NO. DESCRIPTION QTY. P/N 300 psi/ 2000 kpa Water Pressure Gauge.. 2 23005 20 3/4" Plug............................ 3/4" x /2" Nipple.................... 6 2 /4" Gauge Test Valve................. 3 Model MC Manual Control Station...... 4 Model AD Automatic Drain Valve....... 5 Model ASV Automatic ShutOff Valve... 6 Waterflow Pressure Alarm Switch, 46005002 52200 5232004 2302 2 /2" Union........................... 5 22 3/4" Union........................... 23 /4" 0 Elbow....................... /2" 0 Elbow....................... 3/4" 0 Elbow....................... 4 3/4" x 2" Nipple....................... 42 3/4" x 4" Nipple....................... P 0 psi/ 50 kpa Air Pressure Gauge.... P2 /4" Gauge Test Valve................. 2302 46005002 Model PS02........................ 0 26 3/4" x /2" 0 Elbow.................. P3 Low Air Pressure Alarm Switch, /2" Ball Valve....................... 2 8 /2" Spring Loaded Check Valve......... /2" YStrainer....................... 0 3/4" Swing Check Valve................ 3/4" Angle Valve...................... 46050004 2322002 52353005 4604005 46048005 2 /2" Tee............................ 3 /2" x /4" x /2" Tee.................. 3 2 3/4" Tee............................ 30 3/4" x /2" x 3/4" Tee.................. 2 3 /4" x Close Nipple.................... 2 Model PS02........................ P4 /4" Pressure Relief Valve.............. P5 /2" Swing Check Valve................ P6 /2" Globe Valve..................... P 3/4" Angle Valve...................... 0 230 4604004 46004 4604800 2 Drip Funnel Connector................. 3 Drip Funnel Bracket................... 4 Drip Funnel.......................... 5 3/32" Vent Fitting..................... 6 /4" x 8" Tubing..................... /2" Tubing Connector................. 8 /2" x 2" Tubing..................... /4" Plug............................ 22005 22003 2300 2032002 32 /2" x Close Nipple.................... 3 /2" x /2" Nipple.................... /2" x 2" Nipple....................... 35 /2" x 2/2" Nipple.................... 3 36 /2" x 5" Nipple....................... 2 3 /2" x " Nipple....................... 38 Select Nipple per Table................ 3 Select Nipple per Table................ /4" Plug............................ 3 P /2" x /4" Reducing Bushing............ P0 /2" Union........................... P /2" 0 Elbow....................... P2 /2" Cross........................... P3 /2" x /2" x /4" Tee.................. P4 " x 3/4" x /2" Tee.................... P5 /4" x 3" Nipple....................... /2" x /2" Nipple.................... 5 P /2" x 2/2" Nipple.................... 3/4" x /2" Nipple.................... P " x 2" Nipple........................ P5 P4 COMPONENTS INCLUDED ONLY IN P P0 PRETRIMMED ASSEMBLIES: A Model CVFR Check Valve, 2" (DN50)... 550020 P3 P3 /2" (DN)........................ 50A 6 2" (DN50)........................... 502A P A3 Figure 5 Coupling: P5 /2" (DN)........................ 55ACP P P6 2" (DN50)........................... 520ACP 5 P2 26 A4 Coupling for /2" (DN) DV5: (GREEN Figure 6 Reducing Coupling, 2" x /2".. 6205ES TINT) 6 Coupling for 2" (DN50) DV5: P2 Figure 5 Coupling, 2"................ 520ACP P 30 Select Appropriate Nipple Sizes Nipple 2 per DV5 Deluge Valve Size 20 Number P P /2" (DN) 2" (DN50) 4 P4 38 /2" x Close /2" x 2" 35 PLUG 3 /2" x 5" /2" x 5/2" 2 2 UNUSED 4 4 PORTS LOCATION 22 3 36 2 32 2 A2 Butterfly Valve, Power Ball 300: FOR OPTIONAL ELECTRICALLY SUPERVISED 0 2 N.O. ALARM A 3 CONTROL 35 30 A4 2 38 32 42 3 8 35 3 A3 2 2 5 A2 2. Supervised Single Interlock 36 32 Preaction Trim with Wet Pilot 8 Actuation Trim is comprised of 3 Items 42 plus Items PP. 2" (DN50) Items AA4 included only in 23 3 GROOVE x GROOVE 2 pretrimmed valve assemblies DV5 DELUGE as applicable; otherwise SHOWN ordered separately. 4. See Figure 2 of TFP305 for 2. All Fittings and Nipples are Deluge Valve Port identification. galvanized (Standard Order). 5. Route all Tubing to Drip Funnel, 3. : Common Hardware. Item 4. FIGURE 3A ( OF 3) /2 AND 2 IN (DN AND DN50) DV5 SUPERVISED SINGLE INTERLOCK PREACTION SYSTEM WITH WET PILOT ACTUATION TRIM EXPLODED VIEW
TFP Page 6 of 4 NO. DESCRIPTION QTY. P/N NO. DESCRIPTION QTY. P/N NO. DESCRIPTION QTY. P/N 300 psi/ 2000 kpa Water Pressure Gauge.. 2 23005 /2" Tubing Connector................. 2 3/4" Tee............................ 2 /4" Gauge Test Valve................. 46005002 8 /2" x 8" Tubing..................... 30 3/4" x /2" x 3/4" Tee.................. 2 3 Model MC Manual Control Station...... 52200 /4" Plug............................ 3 /4" x Close Nipple.................... 2 4 Model AD Automatic Drain Valve....... 5232004 20 3/4" Plug............................ 32 /2" x Close Nipple.................... 2 5 Model ASV Automatic ShutOff Valve... 2302 2 /2" Union........................... 5 /2" x /2" Nipple.................... 3 6 Waterflow Pressure Alarm Switch, 22 3/4" Union........................... /2" x 2/2" Nipple.................... Model PS02........................ 0 23 /4" 0 Elbow....................... 35 /2" x 3/2" Nipple.................... /2" Ball Valve....................... 2 46050004 /2" 0 Elbow....................... 36 /2" x 4" Nipple....................... 8 /2" Spring Loaded Check Valve......... 2322002 3/4" x /2" 0 Elbow.................. 3 /2" x 4/2" Nipple.................... /2" YStrainer....................... 52353005 26 /4" 0 Elbow...................... 38 /2" x 5" Nipple....................... 0 3/4" Swing Check Valve................ 4604005 2 /2" Tee............................ 3 3 /2" x 5/2" Nipple.................... /4" Angle Valve.................... 4604800 /2" x /4" x /2" Tee.................. 3 /2" x " Nipple....................... 2 2 Drip Funnel Connector................. 22005 4 3/4" x /2" Nipple.................... 5 3 Drip Funnel Bracket................... 22003 42 3/4" x 2" Nipple....................... 4 Drip Funnel.......................... 2300 43 /4" x 2" Nipple..................... 5 3/32" Vent Fitting..................... 2032002 44 /4" x 4" Nipple..................... 6 /4" x 8" Tubing..................... P4 P 0 psi/ 50 kpa Air Pressure Gauge.... 2302 P3 P2 /4" Gauge Test Valve................. 46005002 P6 P3 Low Air Pressure Alarm Switch, Model PS02........................ 0 P5 P4 /4" Pressure Relief Valve.............. 230 P P5 /2" Swing Check Valve................ 4604004 P P0 P3 4 P6 /2" Globe Valve..................... 46004 P /4" Angle Valve.................... 4604800 /4" Plug............................ 3 P /2" x /4" Reducing Bushing............ 6 P P0 /2" Union........................... P5 P /2" 0 Elbow....................... P2 P2 /2" Cross........................... 5 P2 4 P3 /2" x /2" x /4" Tee.................. 2 P4 /4" x /4" x /2" Tee............... (GREEN P5 /4" x 3" Nipple....................... TINT) 6 /2" x /2" Nipple.................... 6 4 2 P /4" x 2" Nipple..................... P /4" x 3" Nipple..................... 20 COMPONENTS INCLUDED ONLY IN 30 3 P PRETRIMMED ASSEMBLIES: PLUG A Model CVFR Check Valve, 3" (DN80)... 550030 P4 UNUSED A2 Model BFVN Butterfly Valve, 3" (DN80)... 5300F030N PORTS A3 Figure 5 Coupling, 3" (DN80).......... 2 530ACP 2 4 42 22 A 3 2 2 LOCATION FOR OPTIONAL 4 36 ELECTRICALLY 4 2 SUPERVISED 0 N.O. ALARM 4 CONTROL A3 30 2 26 43 44 38 5 3 8 2 2 2 A3 35 32 8. Supervised Single Interlock 3 A2 Preaction Trim with Wet Pilot Actuation Trim is comprised of 3 Items 44 plus Items P. Items AA3 included only in 23 3 pretrimmed valve assemblies 3" (DN80) 2 as applicable; otherwise GROOVE x GROOVE ordered separately. DV5 DELUGE 4. See Figure 2 of TFP305 for SHOWN 2. All Fittings and Nipples are Deluge Valve Port identification. galvanized (Standard Order). 5. Route all Tubing to Drip Funnel, 3. : Common Hardware. Item 4. FIGURE 3A (2 OF 3) 3 IN (DN80) DV5 SUPERVISED SINGLE INTERLOCK PREACTION SYSTEM WITH WET PILOT ACTUATION TRIM EXPLODED VIEW
TFP Page of 4 NO. DESCRIPTION QTY. P/N 300 psi/ 2000 kpa Water Pressure Gauge.. 2 23005 2 /4" Gauge Test Valve................. 46005002 3 Model MC Manual Control Station...... 52200 4 Model AD Automatic Drain Valve....... 5232004 5 Model ASV Automatic ShutOff Valve... 2302 6 Waterflow Pressure Alarm Switch, Model PS02........................ 0 /2" Ball Valve....................... 2 46050004 8 /2" Spring Loaded Check Valve......... 2322002 /2" YStrainer....................... 52353005 0 3/4" Swing Check Valve................ 4604005 Item No. Not Used 2 2" Angle Valve....................... 4604800 3 Drip Funnel Connector................. 22005 4 Drip Funnel Bracket................... 22003 5 Drip Funnel.......................... 2300 6 3/32" Vent Fitting..................... 2032002 /4" x " Tubing..................... 8 /2" Tubing Connector................. /2" x " Tubing..................... 20 /4" Plug............................ 2 3/4" Plug............................ 22 /2" Union........................... 5 23 " Union............................ /4" 0 Elbow....................... /2" 0 Elbow....................... 26 /2" Tee............................ 3 2 LOCATION FOR OPTIONAL ELECTRICALLY SUPERVISED N.O. ALARM CONTROL 2 35 44. Supervised Single Interlock Preaction Trim with Wet Pilot Actuation Trim is comprised of Items 4 plus Items PP. Items AA3 included only in pretrimmed valve assemblies as applicable; otherwise ordered separately. 2. All Fittings and Nipples are galvanized (Standard Order). 3. : Common Hardware. P 6 6 (GREEN TINT) P P 45 3 P4 20 32 0 P0 P2 2 NO. DESCRIPTION P5 43 QTY. P/N 2 /2" x /4" x /2" Tee.................. 3 3/4" x /2" x 3/4" Tee.................. 2 2 " x /2" 0 Elbow.................... 30 " x 3/4" x " Tee..................... 3 2" 0 Elbow......................... 32 /4" x Close Nipple.................... 2 /2" x Close Nipple.................... 2 /2" x /2" Nipple.................... 0 35 /2" x 2/2" Nipple.................... 2 36 /2" x 3" Nipple....................... 3 /2" x 5" Nipple....................... 2 38 /2" x 6" Nipple....................... 3 /2" x " Nipple....................... 2 Select Nipple per Table................ 4 Select Nipple per Table................ 42 Select Nipple per Table................ 43 3/4" x /2" Nipple.................... 44 3/4" x 2" Nipple....................... 45 Select Nipple per Table................ 46 " x Close Nipple..................... 2 4 " x 3" Nipple........................ 4 2 3 22 P3 P P5 46 P6 30 P 4 4 P P4 3 2 32 4" (DN00) GROOVE x GROOVE DV5 DELUGE SHOWN 3 PLUG UNUSED PORTS 23 46 P2 26 P3 2 36 4 5 4 NO. DESCRIPTION 48 Item No. Not Used 4 2" x 3" Nipple........................ 2 Nipple No. 4" 4 42 45 (DN00) /2" x 2/2" /2" x 2" /2" x 6/2" 3/4" x 2/2" QTY. P/N P 0 psi/ 50 kpa Air Pressure Gauge.... 2302 P2 /4" Gauge Test Valve................. 46005002 P3 Low Air Pressure Alarm Switch, Model PS02........................ 0 P4 /4" Pressure Relief Valve.............. 230 P5 /2" Swing Check Valve................ 4604004 P6 /2" Globe Valve..................... 46004 P 2" Angle Valve....................... 4604800 /4" Plug............................ 3 P /2" x /4" Reducing Bushing............ P0 /2" Union........................... P /2" 0 Elbow....................... P2 /2" Cross........................... P3 /2" x /2" x /4" Tee.................. P4 2" x 2" x /2" Tee..................... P5 /4" x 3" Nipple....................... /2" x /2" Nipple.................... 6 P 2" x 3" Nipple........................ 2 COMPONENTS INCLUDED ONLY IN PRETRIMMED ASSEMBLIES: A Model CVFR Check Valve: 4" (DN00).......................... 6" (DN50).......................... 8" (DN200).......................... A2 Model BFVN Butterfly Valve: 4" (DN00).......................... 6" (DN50).......................... 8" (DN200).......................... A3 Figure 5 Coupling: 4" (DN00).......................... 2 6" (DN50).......................... 2 8" (DN200).......................... 2 Select Appropriate Nipple Sizes per DV5 Deluge Valve Size 22 5500 550060 550080 5300F0N 5300F060N 5300F080N 5ACP 560ACP 580ACP 6" 8" (DN50) (DN200) /2" x 5/2" /2" x 8 /2" /2" x 3" /2" x 3/2" /2" x /2" /2" x " 3/4" x 3/2" 3/4" x 4/2" 3 2 4. See Figure 2 of TFP305 for Deluge Valve Port identification. 5. Route all Tubing to Drip Funnel, Item 5. FIGURE 3A (3 OF 3) 4, 6, AND 8 IN (DN00, DN50 AND DN200) DV5 SUPERVISED SINGLE INTERLOCK PREACTION SYSTEM WITH WET PILOT ACTUATION TRIM EXPLODED VIEW A2 A A3 A3 35 22 5 8 38 42 22 26 3 4 26 3 8 22
TFP Page 8 of 4. Use only 2" (DN50) Model CVFR Riser Check Valve in /2" (DN) and 2" (DN50) assemblies. Use CVFR Valve size equal to mating DV5 Valve in larger assemblies. 2. Nipples 4 vary in length relative to DV5 size. Select per table. All other nipples packed unassembled shall be installed per appropriate trim exploded view, Figure 3A Part, 2, or 3. 3. Install subassemblies in alphabetical order. 4. See Figure 2 of TFP305 for Deluge Valve Port identification. 5. Route all Tubing to Drip Funnel. 3/4 IN NPT CONNECTION FOR WATER MOTOR ALARM LOCATION FOR OPTIONAL ELECTRICALLY SUPERVISED N.O. ALARM CONTROL WATERFLOW PRESSURE ALARM SWIT NIPPLE MAIN DRAIN (NORMALLY CLOSED) SYSTEM WATER SUPPLY PRESSURE GAUGE ALARM TEST (NORMALLY CLOSED) NIPPLE 4 B SYSTEM MAIN DRAIN CONNECTION (SIZED PER TABLE) SYSTEM MAIN DRAIN (NORMALLY CLOSED) C Nipple Select Appropriate Nipple Sizes per DV5 Deluge Valve Size Number 2 /2" (DN) /2" x Close /2" x Close 2" (DN50) /2" x 2" /2" x Close 3" (DN80) /2" x /2" /2" x /2" 4" (DN00) /2" x 2/2" /2" x 2" 6" (DN50) /2" x 5/2" /2" x 3" 8" (DN200) /2" x 8/2" /2" x 3/2" 3 /2" x 5" /2" x 5/2" /2" x " /2" x 6/2" /2" x /2" /2" x " 4 3/4" x /2" 3/4" x /2" 3/4" x /2" 3/4" x 2/2" 3/4" x 3/2" 3/4" x 4/2" System Main Drain 3/4" NPT 3/4" NPT /4" NPT 2" NPT 2" NPT 2" NPT Size Main Drain Size VENT FITTING (GREEN TINT) AUTOMATIC DRAIN E MAIN DRAIN CONNECTION (SIZED PER TABLE) 3/4" NPT 3/4" NPT /4" NPT 2" NPT 2" NPT SYSTEM AIR SUPPLY CONTROL (NORMALLY OPEN) DRIP FUNNEL WITH /4 IN NPT CONNECTION TO DRAIN PLUG UNUSED PORTS A F 4" (DN00) FLANGE x GROOVE DV5 DELUGE SHOWN LOW AIR PRESSURE ALARM SWIT /2 IN NPT CONNECTION FOR SYSTEM AIR SUPPLY SYSTEM AIR SUPPLY PRESSURE GAUGE /2 IN NPT CONNECTION FOR "WET PILOT RISER DETECTION" ECK (NOTE ) AUTOMATIC SHUTOFF (NORMALLY OPEN) DIAPHRAGM AMBER SUPPLY CONTROL (NORMALLY /2 IN NPT OPEN) CONNECTION FROM WATER SUPPLY D NIPPLE 2 FIGURE 3B /2 THRU 8 IN (DN THRU DN200) DV5 SUPERVISED SINGLE INTERLOCK PEACTION WITH WET PILOT ACTUATION TRIM OPERATIONAL COMPONENTS SEMIPREASSEMBLED TRIM EXPLODED ARRANGEMENT NIPPLE 3 MANUAL CONTROL STATION 2" NPT DIAPHRAGM AMBER PRESSURE GAUGE
TFP Page of 4 Valve Size /2" (DN) 2" (DN50) 3" (DN80) 4" (DN00) 6" (DN50) 8" (DN200) A B C D E F G H J K L M.00 (,8).3 (8,0).8 (8,4) 0.00 (4,0).38 (,0) 2.00 (304,8) 8.88 (2,4).3 (23,8) 0.44 (265,).5 (,5) 4.3 (363,5) 6.00 (6,4) 3.00 (0,2) 3.00 (0,2) 4.50 (368,3).88 (454,0) 8.5 (46,3) 2. (53,8) 0.50 (266,) 0.50 (266,) 0.50 (266,) 0.50 (266,) 0.50 (266,) 0.50 (266,) Nominal Installation Dimensions in Inches and (mm) 20.50 (520,) 2.06 (535,0).00 (635,0) 2.3 (3,8) 3.4 (8,2) 36.5 (,5) 4.00 (0,6) 3.3 (,4).6 (42,).5 (44,5) 3.50 (88,).5 (44,5) 5.8 (4,6) 6.00 (52,4) 6.6 (0,0) 6.50 (65,).88 (200,0) 0.5 (23,) * MINIMUM CLEARANCE. 5.8 (4,6) 6.00 (52,4) 6.6 (0,0) 8.56 (2,5).4 (2,4) 0.63 (26,) 3.00 (6,2) 3.00 (6,2) 4. (08,0) 6. (58,8) 6. (58,8) 6. (58,8) A* B C* D*.00 (,8).00 (,8).00 (,8).3 (8,0).3 (8,0).3 (8,0) 4.00 (0,6) 3.3 (,4) 0. (6,4) 0.38 (,5).56 (3,).3 (8,0) 4.8 (36,2) 5.38 (30,5) 2.3 (536,6).38 (644,5) 2.63 (52,5) 36.50 (2,) N 4.02 (02,) 4.0 (03,) 3.85 (8,0) 4.56 (6,0) 5.86 (4,0) 5.26 (,0) M E* L F G N H J K LEFT VIEW FRONT VIEW FIGURE 4 /2 THRU 8 IN (DN THRU DN200) DV5 SUPERVISED SINGLE INTERLOCK PREACTION WITH WET PILOT ACTUATION TRIM NOMINAL INSTALLATION DIMENSIONS
TFP Page 0 of 4 Supply Pressure, () PSI (Bar) 20 (,4) (2,8) 60 (4,) 80 (5,5) 00 (6,) 20 (8,3) (,) 60 (,0) 5 (2,) 200 (3,8) 2 (5,5) 0 (,2) /2" (DN) (,4) (,3) 46 (4,0) 58 (,8) 8 (23,8) 8 (26,5) 05 (32,0) 2 (38,) (,8) 60 (48,8) 85 (56,4) 20 (6,3) 2" (DN50) 3 (0,) (5,8) 38 (,6) 54 (6,5) 8 (23,8) 8 (26,5) 0 (32,6) 23 (3,5) 38 (42,) 60 (48,8) 66 (50,6) (60,) Maximum Pilot Height, (2) Feet (Meters) 3" (DN80) (,4) 30 (,) 52 (5,8) 0 (2,3) 3 (,3) (35,) 3 (42,4) 6 (4,) 2 (52,4) 206 (62,8) 23 (2,2) (6,5) 4" (DN00) (5,2) 3 (,) 54 (6,5) 60 (8,3) 8 (23,8) 5 (,) 42 (43,3) 6 (53,6) (52,) 223 (68,0) 2 (,0) (5,3) 6" (DN50) () If supply pressure is variable, assume minimum expected value. (2) Maximum pilot height for up to 500 feet (50 meters) of equivalent length of pilot line (pipe plus fittings). (3) Interpolation between data points is permitted. 8 (5,5) 38 (,6) 56 (,) 0 (2,3) (30,2) 30 (3,6) 54 (46,) 6 (4,) 4 (5,) 26 (65,8) 6 (5,0) (83,8) 8" (DN200) (2,) 38 (,6) 44 (3,4) 58 (,8) 65 (,8) 6 (2,3) 4 (43,0) 0 (5,8) 4 (5,) 206 (62,8) 0 (6,2) (8,3) TABLE A /2 THRU 8 IN (DN THRU DN200) DV5 WET PILOT DESIGN CRITERIA FOR UP TO 500 FEET OF EQUIVALENT LENGTH OF PILOT LINE (PIPE PLUS FITTINGS) Wet Pilot Lines must be maintained at a minimum temperature of F (4 C). At a minimum, it is recommended that internally galvanized pipe and cast iron fittings be used for wet pilot lines. System Air Pressure Requirements The supervisory air (nitrogen) pressure is to be 0 ± 2 psi (0,6 ± 0,4 bar). The use of a higher supervisory pressure is subject to approval by the authority having jurisdiction, and it should be understood that the use of a higher supervisory pressure may increase water delivery time. The use of a lower supervisory pressure may prevent clearing the alarm of the Supervisory Low Pressure Alarm Switch (Item P3 Fig. 3A), which is factory set to alarm at 5 ± psi (0, ± 0,0 bar) on decreasing pressure. The supervisory air supply pressure of 0 ± 2 psi (0,6 ± 0,4 bar) can be provided by any of the following methods. Refer to the applicable data sheet for laboratory approval information. Model G6AC82 (selfcontained) Automatic Supervisory Air Supply described in Technical Data Sheet TF20. A maximum 200 psi (3,8 bar) plant air supply in combination with the Model AMD Air Maintenance Device described in Technical Data Sheet TFP22. A maximum 3000 psi (206, bar) nitrogen cylinder in combination with the Model AMD3 Nitrogen Maintenance Device described in Technical Data Sheet TFP. NOTE: The dew point of the air or nitrogen supply for a system exposed to freezing conditions must be maintained below the lowest ambient temperature to which the system piping will be exposed. Introduction of moisture into the system piping can create ice build up that could prevent proper operation of the system. The Supervisory Low Pressure Alarm Switch (Item P3 Fig. 3A) is factory set at 5 ± psi (0, ± 0,0 bar) on decreasing pressure. The Pressure Relief Valve (Item P4 Fig. 3A) is factory set to fully open at ± 2 psi (,2 ± 0,4 bar) and it begins to crack open at a pressure of about 8 psi (, bar). Friction Loss The nominal pressure loss versus flow data for the DV5 Deluge Valve plus Riser Check Valve is provided in Graph A.
Installation General Instructions /2 inch (DN) risers utilize a 2 inch (DN50) Riser Check Valve in combination with the /2 inch (DN) DV5 Deluge Valve. Proper operation of the DV5 Deluge Valves depends upon their trim being installed in accordance with the instructions given in this technical data sheet. Failure to follow the appropriate trim diagram may prevent the DV5 Valve from functioning properly, as well as void listings, approvals, and the manufacturer s warranties. The DV5 Valve must be installed in a readily visible and accessible location. The DV5 Valve, associated trim, and wet pilot lines must be maintained at a minimum temperature of F (4 C). Heat tracing of the DV5 Valve or its associated trim is not permitted. Heat tracing can result in the formation of hardened mineral deposits that are capable of preventing proper operation. The DV5 Deluge Valve is to be installed in accordance with the following criteria: Step. All nipples, fittings, and devices must be clean and free of scale and burrs before installation. Use pipe thread sealant sparingly on male pipe threads only. Step 2. The DV5 Valve must be trimmed in accordance with Figure 3A or 3B. Step 3. Care must be taken to ensure that check valves, strainers, globe valves, etc. are installed with the flow arrows in the proper direction. Step 4. Drain tubing to the Drip Funnel must be installed with smooth bends that will not restrict flow. Step 5. The main drain and Drip Funnel drain may be interconnected provided a check valve is located at least 2 inches (300 mm) below the Drip Funnel. Step 6. Suitable provision must be made for disposal of drain water. Drainage water must be directed such that it will not cause accidental damage to property or danger to persons. Step. Connect the Diaphragm Chamber Supply Control Valve to the inlet side of the system s Main Control Valve in order to facilitate setting of the DV5 Valve (Ref. Figure 4). Step 8. An Inspector s Test Connection, as described in the Technical Data section, must be provided for Wet Pilot Actuation systems. Step. Unused pressure alarm switch connections must be plugged. Step 0. A suitable automatic supervisory air (nitrogen) supply, as described in the Technical Data section, is to be installed in accordance with the applicable technical data sheet and set for 0 ± 2 psi (0,6 ± 0,4 bar). Step. A desiccant dryer, when required for the supervisory air supply, is to be installed between a drip leg and the Model AMD Air Maintenance Device or between the Model G6AC82 Automatic Supervisory Air Supply and the Preaction Trim. Step 2. The Supervisory Low Pressure Alarm Switch is to be wired to the supervisory alarm initiating circuit of an alarm panel. Step 3. Conduit and electrical connections are to be made in accordance with the requirements of the authority having jurisdiction and/or the National Electric Code. Step 4. Before a system hydrostatic test is performed in accordance with NFPA 3 system acceptance test requirements, the DV5 Diaphragm Chamber is to be depressurized; the Automatic Drain Valve (Item 4, Fig. 3A) is to be temporarily replaced with a /2 inch NPT plug, the 3/32 inch Vent Fitting (Item 6 Fig. 3A) is to be temporarily replaced with a /4 inch NPT plug, and the Diaphragm Cover Bolts must be uniformly and securely tightened using a crossdraw sequence. After tightening, double check to make certain that all of the Diaphragm Cover Bolts are securely tightened. Valve Setting Procedure Steps through 2 are to be performed when initially setting the DV5 Deluge Valve after an operational test of the fire protection system, or after system operation due to a fire. Step. Close the Main Control Valve. Step 2. Close the Diaphragm Chamber Supply Control Valve, and close the Air Supply Control Valve (Ref. Fig. 3B). Step 3. Open the Main Drain Valve, System Drain Valve, and all auxiliary drains in the system. Close the System Drain Valve and auxiliary drain valves after water ceases to discharge. Leave the Main Drain Valve open. Step 4. Depress the plunger of the Automatic Drain Valve to verify that it is open and that the DV5 Valve is completely drained. Step 5. Clean the Strainer in the Diaphragm Chamber Supply connection by removing the cleanout plug and strainer basket. The Strainer may be TFP Page of 4 flushed out by momentarily opening the Diaphragm Chamber Supply Control Valve. Step 6. Reset the actuation system. Manual Actuation Push the operating lever up; however, do not close the hinged cover at this time. Wet Pilot Actuation Replace operated pilot sprinklers and/or reset the manual control stations. NOTE: In order to prevent the possibility of a subsequent operation of an overheated solder type pilot sprinkler, any solder type pilot sprinklers that were possibly exposed to a temperature greater than their maximum rated ambient must be replaced. Step. Open the Diaphragm Chamber Supply Control Valve and allow time for full pressure to build up in the Diaphragm Chamber. Step 8. Operate (open) the Manual Control Station to vent trapped air from the Diaphragm Chamber. If necessary, first open the hinged cover, and then fully pull down on the operating lever. Slowly close the operating lever by pushing it up after aerated water ceases to discharge from the Manual Control Station drain tubing. Close the hinged cover and insert a new break rod in the small hole through the top of the enclosing box. Crack open the Inspector s Test Connection and any other vent valves on the wet pilot line to relieve trapped air. After the discharge of air has stopped, close the vent valves and the Inspector s Test Connection Step. Inspect the drain connections from the Manual Control Station. Any leaks must be corrected before proceeding to the next step. Step 0. Verify the ability for the DV5 Diaphragm to hold pressure as follows: With the diaphragm chamber pressurized per Step 8, temporarily close the Diaphragm Chamber Supply Control Valve, and then monitor the Diaphragm Chamber Pressure Gauge for a drop in pressure. If a drop in pressure is noted, the DV5 Diaphragm is to be replaced and/or any leaks must be corrected before proceeding to the next step. If the Diaphragm Chamber Pressure Gauge indicates no drop in pressure, reopen the Diaphragm Chamber Supply Control Valve and proceed to the next step. Step. Replace operated automatic sprinklers on the system piping and then open the Supervisory Air Supply Control Valve and allow the system to automatically reestablish its nominal
TFP Page 2 of 4 NOMINAL PRESSURE DROP IN POUNDS PER SQUARE IN (PSI) 5.0 0.0.0 8.0.0 6.0 5.0 4.0 3.0 2.0.0 0. 0.8 0. 0.6 0.5 0.4 50 /2 IN (DN) 00 2 IN (DN50) FLOW RATE IN LITRES PER MINUTE (LPM) ( GPM = 3,85 LPM) 200 0 600 000 2000 3000 5000 000 0000 3 IN (DN80) 4 IN (DN00) 6 IN (DN50) 8 IN (DN200) 200 0 600 000 2000 3000 FLOW RATE IN GALLONS PER MINUTE (GPM),00 0,0 0,80 0,0 0,60 0,50 0, 0,30 0,20 0,0 0,0 0,08 0,0 0,06 0,05 0,04 0,03 NOMINAL PRESSURE DROP IN BAR ( PSI = 0,0685 BAR) The approximate friction loss, based on the Hazen and Williams formula and expressed in equivalent length of pipe with C20, is as follows: 5 feet of /2 Sch. pipe for the /2 inch Valve Combination** calculated on a typical flow rate of 00 gpm. feet of 2 inch Sch. pipe for the 2 inch Valve Combination* calculated on a typical flow rate of 5 gpm. 3 feet of 3 inch Sch. pipe for the 3 inch Valve Combination* calculated on a typical flow rate of 350 gpm. 48 feet of 4 inch Sch. pipe for the 4 inch Valve Combination* calculated on a typical flow rate of 600 gpm. 3 feet of 6 inch Sch. pipe for the 6 inch Valve Combination* calculated on a typical flow rate of 500 gpm. 03 feet of 8 inch Sch. 30 Pipe for the 8 inch Valve Combination* calculated on a typical flow rate of 00 gpm. GRAPH A DELUGE AND ECK COMBINATION* NOMINAL PRESSURE LOSS VERSUS FLOW *DV5 Deluge Valve combined with Model CVFR Riser Check Valve **/2 Inch DV5 Deluge combined with 2 Inch Model CVFR Riser Check Valve
air pressure of 0 psi (0,6 bar). Observe the Automatic Drain Valve for leaks. If there are leaks, determine/correct the cause of the leakage problem within the Riser Check Valve. NOTE: In order to prevent the possibility of a subsequent operation of an overheated solder type automatic sprinkler, any solder type automatic sprinklers that were possibly exposed to a temperature greater than their maximum rated ambient must be replaced. Step 2. Slowly open the Main Control Valve. Close the Main Drain Valve as soon as water discharges from the drain connection. Observe the Automatic Drain Valve for leaks. If there are leaks, determine/correct the cause of the leakage problem. If there are no leaks, the DV5 Valve is ready to be placed in service and the Main Control Valve must then be fully opened. When the Main Control Valve is opened, the pressure on the Diaphragm Chamber may increase. This increase in pressure is normal, and if the pressure is greater than 0 psi (,2 bar), the pressure is to be relieved by partially and temporarily opening the Manual Control Station; however, do not allow the pressure as indicated on the Diaphragm Chamber Pressure Gauge to drop below the supply pressure shown on the Water Supply Pressure Gauge, since this action may result in tripping of the DV5 Valve. After setting a fire protection system, notify the proper authorities and advise those responsible for monitoring proprietary and/or central station alarms. Care and Maintenance The following procedures and inspections must be performed as indicated, in addition to any specific requirements of the NFPA, and any impairment must be immediately corrected. Before closing a fire protection system main control valve for maintenance work on the fire protection system that it controls, permission to shut down the affected fire protection systems must first be obtained from the proper authorities and all personnel who may be affected by this action must be notified. The owner is responsible for the inspection, testing, and maintenance of their fire protection system and devices in compliance with this document, as well as with the applicable standards of the National Fire Protection Association (e.g., NFPA ), in addition to the standards of any authority having jurisdiction. Contact the installing contractor or product manufacturer with any questions. It is recommended that automatic sprinkler systems be inspected, tested, and maintained by a qualified Inspection Service in accordance with local requirements and/or national codes. NOTICE Some of the procedures outlined in this section will result in operation of the associated alarms. Consequently, notification must first be given to the owner and the fire department, central station, or other signal station to which the alarms are connected. When the system is using either a seawater or brackish water supply, internal and external inspection of the DV5 Valve and Trim is essential. Parts showing any signs of corrosion must be replaced to ensure the integrity of the system. Annual Operation Test Procedure Proper operation of the DV5 Valve (i.e., opening of the DV5 Valve as during a fire condition) must be verified at least once a year as follows: Step. If water must be prevented from flowing beyond the riser, perform the following steps. Close the Main Control Valve. Open the Main Drain Valve. Open the Main Control Valve one turn beyond the position at which water just begins to flow from the Main Drain Valve. Close the Main Drain Valve. TFP Page 3 of 4 Step 2. Open the Wet Pilot Line Inspector s Test Connection. NOTE: Be prepared to quickly perform Steps 3, 4, and 5 if water must be prevented from flowing beyond the riser. Step 3. Verify that the DV5 Valve has tripped, as indicated by the flow of water into the system. Step 4. Close the system s Main Control Valve. Step 5. Close the Diaphragm Chamber Supply Control Valve and the Supervisory Air Supply Control Valve. Step 6. Reset the DV5 Deluge Valve in accordance with the Valve Setting Procedure. Quarterly Waterflow Alarm Test Procedure Testing of the system waterflow alarms must be performed quarterly. To test the waterflow alarm, open the Alarm Test Valve, which will allow a flow of water to the Pressure Alarm Switch and/or Water Motor Alarm. Upon satisfactory completion of the test, close the Alarm Test Valve. Quarterly Supervisory Low Pressure Alarm Test Procedure Proper operation of the Supervisory Low Pressure Alarm Switch must be performed quarterly as follows: Step. Crack open the System Main Drain Valve for the Riser Check Valve (Item P, Figure 3A) to slowly relieve supervisory air pressure from the system. Verify that the Supervisory Low Pressure Alarm Switch is operational and that the low pressure set point is approximately 5 psi (0, bar). Step 2. Close the System Main Drain Valve (Item P, Figure 3A) and allow the system supervisory pressure of 0 ± 2 psi (0,6 ± 0,4 bar) to be automatically reestablished. The Supervisory Low Pressure Alarm Switch should return to its normal condition. Pressure Relief Valve Maintenance Over pressurization of the system piping with air will result in the opening of the Pressure Relief Valve (Item P4, Fig. 3A). If the Relief Valve continues to bleed air after the system pressure has been reduced to its normal supervisory pressure range of 0 ± 2 psi (0,6 ± 0,4 bar), most likely debris became lodged in the seating area. To help clean the seating area, slowly pull up on the ring at the top of the Relief Valve to allow a full flow of air through the Relief Valve, and then release the ring to allow the Relief Valve to snap closed. Repeat the cleaning procedure as necessary.
TFP Page 4 of 4 Limited Warranty For warranty terms and conditions, visit www.tycofire.com. Ordering Procedure The DV5 Deluge Valve with Single Interlock Preaction Wet Pilot Actuation trim can be ordered pretrimmed or nonassembled as separate items. For nonassembled, the following items must be ordered separately: DV5 Deluge Valve Model CVFR Riser Check Valve Coupling Single Interlock Preaction Wet Pilot Actuation Trim, SemiPreassembled Supervisory Air Supply Accessories NOTE: /2 inch (DN) risers utilize a 2 Inch (DN50) Model CVFR Riser Check Valve connected to the /2 inch (DN) DV5 Deluge Valve by a 2 x /2 inch Figure 6 Reducing Coupling. Replacement Trim Parts Specify: (description) for use with DV5 Deluge Valve, P/N (see Figure 3A) DV5 Deluge Valve (Select One) P/Ns are for American Standard Groove x Groove Connections, and Threaded Ports. For other configurations refer to Technical Data Sheet TFP305. Specify: (size) DV5 Groove x Groove Deluge Valve, P/N (specify): /2 Inch...P/N 5 2 Inch...P/N 50 3 Inch...P/N 52 4 Inch...P/N 53 6 Inch...P/N 55 8 Inch...P/N 56 Riser Check Valve (Select One) P/Ns are for American Standard Grooved Connections. For other configurations refer to Technical Data Sheet TFP50 for the Groove x Groove Model CVFR Riser Check Valve. Specify: (size), Model CVFR Groove x Groove Riser Check Valve, P/N (specify): 2 Inch...P/N 550020 3 Inch...P/N 550030 4 Inch...P/N 5500 6 Inch...P/N 550060 8 Inch...P/N 550080 NOTE: For /2 inch (DN) risers, use the 2 Inch (DN50) Riser Check Valve. Coupling (Select One) P/Ns are for American Standard Grooved Connections. For other configurations and finishes refer to Technical Data Sheet TF30 or T80. A coupling to attach the Riser Check Valve to the outlet of the Deluge Valve must be separately ordered. Specify: (size), (Figure #), painted, (description), P/N (specify). For /2 inch risers, order an additional Reducing Coupling for the outlet of the 2 inch Riser Check Valve. 2 x /2 Inch Figure 6 Painted Reducing Coupling.... P/N 6205ES 2 Inch Figure 2 Painted Rigid Coupling...P/N 220ASC 3 Inch Figure 2 Painted Rigid Coupling...P/N 230ASC 4 Inch Figure 2 Painted Rigid Coupling...P/N 0ASC 6 Inch Figure 2 Painted Rigid Coupling...P/N 260ASC 8 Inch Figure 2 Painted Rigid Coupling...P/N 0ASC Preaction Trim (Select One) Specify: (specify size and finish galvanized is standard) SemiPreassembled Supervised Single Interlock Preaction System With Wet Pilot Actuation Trim for DV5 Deluge Valves, P/N (specify): /2 & 2 Inch Galvanized...P/N 582 /2 & 2 Inch Black...P/N 58 3 Inch Galvanized...P/N 5824 3 Inch Black...P/N 584 4, 6 & 8 Inch Galvanized...P/N 582 4, 6 & 8 Inch Black...P/N 58 Supervisory Air Supply (Select One) A device capable of maintaining a nominal system air or nitrogen pressure of nominal 0 psi (0,6 bar) must be separately ordered. Specify: (model and description), P/N (specify): Model AMD Air Maintenance Device (TFP22)... P/N 5232002 Model AMD3 Nitrogen Maintenance Device (TFP)... P/N 523200 Model G6AC82 Automatic Supervisory Air Supply (TF20)... P/N 5000 Pretrimmed DV5 Assembly with Butterfly Valve Specify: (size), G x G End Connection, Pretrimmed DV5 Assembly with Butterfly Valve, P/N (specify): /2 Inch G x G...P/N 52AP 2 Inch G x G...P/N 520AP 3 Inch G X G...P/N 520AP 4 Inch G x G...P/N 524AP 6 Inch G x G...P/N 526AP 8 Inch G x G...P/N 5AP Pretrimmed DV5 Assembly without Butterfly Valve Specify: (specify size), (specify) End Connection, Pretrimmed DV5 Assembly without Butterfly Valve, P/N (specify): 3 Inch F x G...P/N 522AP 4 Inch F x G...P/N 52442AP 6 Inch F x G...P/N 52642AP 8 Inch F x G...P/N 542AP Accessories (as needed) Specify: (description), P/N (specify): 600 psi Water Pressure Gauge....P/N 23004 Model WMA Water Motor Alarm (TFP2)....P/N 5263000P Model MC Manual Control Station with galvanized connections for remote wet pilot actuation (TFP382)...P/N 52200 GLOBAL HEADQUARTERS 0 Pennbrook Parkway, Lansdale, PA 446 Telephone +362000 Copyright 204 Tyco Fire Products, LP. All rights reserved.