DT & SPEIFITIONS Services, Wärtsilä Finland Oy Engine section Engine type Ref. Date Issue. Page 02 Luricating oil W46F WFI S 21-Oct-09 01 4602N004 1(2)+8 Luricating oils for WÄRTSILÄ 46 engines General Letter distriution Letter validity Enclosure The enclosed specification contains oil requirements and quality for WÄRTSILÄ 46F engines. Wärtsilä Services Network and operators/owners of engines concerned. Until further notice. Requirements and oil quality DE0570, rev., 8 pages. Wärtsilä Finland Oy P.O. Box 252 (Tarhaajantie 2) Telecop. +358 10 709 1847 Tel. +358 10 709 0000 Business ID 0773744-3 Services, Vaasa FIN-65101 Vaasa, Finland Telecop. +358 10 709 1380 Registered Office: Vaasa Wärtsilä Finland Oy P.O. Box (Stålarminkatu 45) Telecop. +358 10 709 3279 Tel. +358 10 709 0000 Services, Turku FIN-811 Turku, Finland Telecop. +358 10 709 3410
Services, Wärtsilä Finland Oy Data & Specification Issue. Page 01 4602N004 2(2)+8 09 Wärtsilä Finland Oy ll rights reserved No part of this pulication may e reproduced or copied in any form or y any means (electronic, mechanical, graphic, photocopying, recording, taping or other information retrieval systems) without the prior written permission of the copyright holder. Wärtsilä Finland Oy makes no representation, warranty (express or implied) in this pulication and assumes no responsiility for the correctness, errors or omissions for information contained herein. Information in this pulication is suject to change without notice. Unless otherwise expressly set forth, no recommendation contained in this document is to e construed as provided due to a defect in the engine, ut merely as an improvement of the engine and/or the maintenance procedures relating thereto. ny actions y the owner/operator as a result of the recommendations are not covered under any warranty provided y Wärtsilä and such actions will thus e at the owners/operators own cost and expense. NO LIBILITY WHETHER DIRET, INDIRET, SPEIL, INIDENTL OR ONSEQUENTIL, IS SSUMED WITH RESPET TO THE INFORMTION ONTINED HEREIN. THIS PUBLITION IS ONFIDENTIL ND INTENDED FOR INFORMTION PURPOSES ONLY.
Wärtsilä Finland Oy Finland INSTLLTION MNUL 3. Luricating oil system This doc is the property of Wärtsilä orp. and shall neither e copied, shown or communicated to a third party without the consent of the owner. Sutitle 3.2. Requirements & oil quality Product 46F Made 11.10.07 K. Juoperi / M. Toija Page DE0570 ppd..10.07 L. Laakso 1 (8) ised date: 25.08.09 hanged y: K. Juoperi pproved y: S. Ghetti D-message No.: 186621 1.2.5 REQUIREMENTS ND OIL QULITY SYSTEM OIL REQUIREMENTS ND QULITY FOR WÄRTSILÄ 46F ENGINES Viscosity Viscosity class Viscosity Index (VI) Min. 95 lkalinity (BN) The required luricating oil alkalinity is tied to the fuel specified for the engine, which is shown in the tale elow. FUEL STNDRDS ND LUBRITING OIL REQUIREMENTS ategory Fuel standard Lue oil BN STM D 975-01, GRDE NO. 1-D, 2-D BS M 100: 1996 DMX, DM 10 - IM 03 DX, D ISO 8217: 05(E) ISO-F-DMX, DM BS M 100: 1996 DMB B IM 03 DB - ISO 8217: 05(E) ISO-F-DMB STM D 975-01, GRDE NO 4-D STM D 396-04, GRDE NO 5-6 BS M 100: 1996 DM, RM10-RMK - IM 03, ISO 8217: 05(E) D, -K700 ISO-F-DM, RM10- RMK In case a low sulphur (S max. 0.2 % m/m) distillate fuel is used, it s recommended to use a luricating oil with BN of 10. It is recommended to use in the first place BN - luricants when operating on heavy fuel. This recommendation is valid especially for engines having wet luricating oil sump and using heavy fuel with sulphur content aove 2.0 % mass. BN luricants can e used when operating on heavy fuel as well if experience shows that the luricating oil BN equilirium remains at an acceptale level. On heavy fuel operation BN luricants are recommended to e used only in special cases, such as installations equipped with an SR catalyst. Lower BN products eventually have a positive influence on cleanliness of the SR catalyst.
2 (8) DE0570 With BN oils luricating oil change intervals may e rather short, ut lower total operating costs may e achieved ecause of etter plant availaility provided that the maintenance intervals of the SR catalyst can e increased. If oth distillate fuel and residual fuel are used periodically as fuel, luricating oil quality has to e chosen according to instructions eing valid for residual fuel operation, i.e. BN is the minimum. Optimum BN in this kind of operation depends on the length of operating periods on oth fuel qualities as well as of sulphur content of fuels in question. Thus in particular cases BN or even higher BN luricating oils should e used. The intervals etween luricating oil changes may e extended y adding oil daily to keep the oil level constantly close to the maximum level. n example of BN depletion curve with different BN luricating oils is shown elow. 60 BN ondening limit: mg KOH/g Oil Volume: 0.6 l/kw (Wet Sump) Fuel sulphur content: 2.5 w-% 0-0 00 00 6000 8000 10000 SERVIE HOURS BN Oil BN Oil BN Oil dditives The oils should contain additives that give good oxidation staility, corrosion protection, load carrying capacity, neutralisation of acid comustion and oxidation residues and should prevent deposit formation on internal engine parts (piston cooling gallery, piston ring zone and earing surfaces in particular). Foaming characteristics Fresh luricating oil should meet the following limits for foaming tendency and staility, according to the STM D 892-92 test method: Sequence I: Sequence II: Sequence III: 100/0 ml 100/0 ml 100/0 ml
3 (8) DE0570 Base oils Use of virgin ase stocks only is allowed, i.e. recycled or re-refined ase oils are not allowed. ONDEMNING LIMITS FOR USED LUBRITING OIL When estimating the condition of used luricating oil, the following properties along with the corresponding limit values must e noted. If the limits are exceeded, measures must e taken. ompare also with guidance values for fresh luricating of the rand used. Property Unit Limit Test method Viscosity cst at max. 25% decrease STM D 445 max. 45% increase Viscosity cst at 100 max. % decrease STM D 445 max. 25% increase Water % V/V max. 0. STM D 95 or D 64 Base Numer mg KOH/g min. in HFO operation, STM D 2896 max. % depletion in LFO operation Insolules % m/min max. 2.0 STM D 893 n-pentane Flash Point, PM Flash Point, O min. 170 min. 190 STM D 93 STM D 92 HNGE OF LUBRITING OIL BRND Top-up with another luricating oil rand than eing filled to the system is not allowed, except if the oth two luricating oils originate from the same manufacturer. E.g. if company s BN oil is filled into the oil system and top-up with same ompany s BN oil is desired, that can e done provided that oth products are ased on same ase oils and additive technology. Otherwise the luricating oil system has to e drained and then filled with another rand y following the procedure descried here elow. In order to minimize the risk of luricating oil foaming, deposit formation, locking of luricating oil filters, damage of engine components, etc., the following procedure should e followed when luricating oil rand is changed from one to another: If possile, change the luricating oil rand in connection with an engine (piston) overhaul Drain old luricating oil from the luricating oil system lean the luricating oil system in case of an excessive amount of deposits on the surfaces of engine components, like crankcase, camshaft compartment, etc. Fill the luricating oil system with fresh luricating oil If the procedure descried aove is not followed, responsiility of possile damage and malfunctions caused y luricating oil change should always e agreed etween an oil company and customer.
4 (8) DE0570 PPROVED LUBRITING OIL QULITIES FOR WÄRTSILÄ 46F ENGINES Should unapproved luricating oils e used during the engine warranty period, and there exist no agreement with the engine manufacturer aout testing, the engine guarantee does not hold. GS OIL ND MRINE DIESEL OIL OPERTION If gas oil or marine diesel oil is used as fuel, luricating oils with a BN of 10-25 are recommended to e used. lso BN luricating oils included in Tale 3 can e used in gas oil and marine diesel oil fuelled engines. Tale 1. pproved system oils - fuel categories and B, recommended in the first place in gas oil or marine diesel oil installations: SUPPLIER BRND NME VISOSITY BN FUEL TEG. BP Energol HPDX Energol I-HFX 4 astrol HLX MHP 4 Seamax Extra TLX Plus 4 hevron (Texaco + altex + FMM) Delo 1000 Marine Delo 00 Marine Taro XD Taro DP ExxonMoil Delvac 16 Moilgard DL Moilgard 4 Moilgard 1 SH Indian Oil orporation Petroras Servo Marine 10 Servo Marine Marrax D-410-P Marrax D-4 Marrax D-4 10 Shell Gadinia Oil Statoil MarWay 10 10.6 Total / Lumarine Disola M Disola M 14
5 (8) DE0570 HEVY FUEL OIL OPERTION Today s modern trunk piston diesel engines are stressing the luricating oils heavily due to a.o. low specific luricating oil consumption. lso ingress of residual fuel comustion products into the luricating oil can cause deposit formation on the surface of certain engine components resulting in severe operating prolems. Due to this many luricating oil suppliers have developed new luricating oil formulations with etter fuel and luricating oil compatiility. The luricating oils mentioned in Tale 2 are representing new detergent/ dispersant additive chemistries and have shown good performance in Wärtsilä engines. Tale 2. pproved system oils - fuel category, recommended in the first place when operating on heavy fuel in order to reach full service intervals. BN - luricating oils preferred in the first place: SUPPLIER BRND NME VISOSITY BN FUEL TEG. BP Energol I-HFX 4 Energol I-HFX 4 astrol TLX Plus 4 TLX Plus 4 TLX Plus 4 epsa hevron (Texaco + altex + FMM) hinese Petroleum orporation ENI S.p.. Troncoil PLUS Troncoil PLUS Ertoil Koral SHF Ertoil Koral SHF Taro XL Taro XL Taro XL X Taro XL X Delo Marine Delo 35 Marine Marilue Oil W 4 Marilue Oil W 4 ladium 0 S ladium 0 S ladium 5 S ExxonMoil Exxmar TP Exxmar TP Moilgard M 4 Moilgard M Fuchs Titan PSW Titan PSW
6 (8) DE0570 SUPPLIER BRND NME VISOSITY BN FUEL TEG. Indian Oil orporation Servo Marine K- Servo Marine K- Servo-Marine K- Lukoil Navigo TPEO / Navigo TPEO / Navigo TPEO / Morris Luricants quamor 1MD quamor 1MD Marine T4 Marine T4 Nippon Oil orporation Pertamina Martron 4 Martron 4 Medripal 4 Medripal 4 Salyx 4 Salyx 4 Petroras Marrax D-4 Marrax D-4 Petron Petromar X Petromar X Petronas Disrol 0 Luricants Disrol 0 International MEO MEO Repsol YPF Neptuno W NT 00 Neptuno W NT 50 Shell rgina X rgina XL Total / Lumarine urelia XL urelia XL urelia TI urelia TI Tale 3. pproved system oils - fuel categories, B and. Luricating oils with BN included in Tale 3 have eventually a positive influence on cleanliness of the SR catalyst. SUPPLIER BRND NME VISOSITY BN FUEL TEG. BP Energol I-HFX 4, astrol TLX Plus 4, epsa Troncoil PLUS, hevron (Texaco + altex + FMM) Ertoil Koral SHF Taro DP Taro DP X Delo 00 Marine,,,,
7 (8) DE0570 SUPPLIER BRND NME VISOSITY BN FUEL TEG. hinese Marilue Oil W 4, Petroleum orporation ENI S.p.. ladium 0 S, ExxonMoil Exxmar TP Moilgard M 4,, Fuchs Titan PSW, Indian Oil Servo Marine K-, orporation Lukoil Navigo TPEO /, Morris Luricants quamor 1MD, Nippon Oil Marine T4, orporation Pertamina Martron 4 Medripal 4 Salyx 4,,, Petroras Marrax D-4, Petron Petromar X, Petronas Disrol 0, Luricants International Shell rgina T, Total / Lumarine urelia XL urelia TI,, Before using a luricating oil not listed in Tales 1-3, the engine manufacturer must e contacted. Luricating oils that are not approved have to e tested according to engine manufacturer s procedures.
8 (8) DE0570 PPROVED LUBRITING OILS FOR ENGINE TURNING DEVIE It is recommended to use EP-gear oils, viscosity 0-0 cst at = ISO VG 460 as luricating oils for turning device. LUBRITING OILS FOR ENGINE TURNING DEVIE SUPPLIER BRND NME VISOSITY cst at VISOSITY cst at 100 VISOSITY INDEX (VI) BP Energol GR-XP 460 460.5 95 astrol lpha SP 460 460.5 95 hevron (Texaco Meropa 460 460 31.6 100 + altex + FMM) ENI S.p.. Blasia 3 0 23.0 95 ExxonMoil Moilgear 600 XP 460 Moilgear 634 460 437.6 27.8 96 96 Shell Omala Oil 460 460.8 97 Total / Lumarine arter EP 460 / Epona Z 460 470.3 93 LUBRITING OILS FOR GOVERNOR / TUTOR (used in Twin Pump engine versions) n oil of viscosity class SE or is suitale and usually the same oil can e used as in the engine. Turocharger oil can also e used in the governor. In low amient conditions it may e necessary to use a multigrade oil (e.g. SE 5W-) to get a good control during start-up. Oil change interval: 00 service hours.