Buyers Guide: Information required: When ordering, please state: 1 Reference Number of Mesh (include any alphabetical suffix) Conventional/Flattened Mesh Dimensions: 1. For conventional (raised) meshes with angled strands inclined from the plane of the sheet. Dimensions from centre to centre of knuckles are shown. Width Thickness 2 Material e.g. Steel 3 Quantity of Sheets and/or Length of Coil 4 or Coil Width (LW dimension first). The diagrams below illustrate this point 5 Raised or Flattened Mesh Knuckle Nominal Short Way of Mesh SW Knuckle 6 Additional Processing or Special Finishes? (Galvanised, Anodised, Powder Coated, Plastic Coated) Sheet Measurements: Long Way of Mesh Pitch LW 2. For flattened meshes, which have been pressure rolled, resulting in strands which are in the same plane as the sheet. Dimensions of the aperture point to point are shown. Width Thickness Long Way e.g. 2440 The sheet above is: 2440 LW x 1220 SW LWM: Long Way of Mesh Dimension Short Way e.g. 1220 Aperture Dimension SW Short Way e.g. 2440 The sheet above is: 1220 LW x 2440 SW SWM: Short Way of Mesh Dimension Long Way e.g. 1220 LWM denotes longest part of diamond SWM denotes shortest part of diamond All standard sheet sizes are nominal (normally oversize). Mild Steel Edging Sections are on page 15. A S F AF SF AG Aluminium Stainless Steel Flattened Aluminium Flattened Stainless Steel Flattened Anodised Gold Aperture dimension LW Glossary of Mesh References: Glossary of Table Suffixes: Key to materials: LWA Long Way Aperture (Length of the Diamond for Flattened Mesh only) SWA Short Way Aperture (Height of the Diamond for Flattened Mesh only) LWD Long Way of the Diamond (measured from point to point horizontally) SWD Short Way of the Diamond (measured from point to point vertically) Swdt Strand Width (Width of Material Feed) Kgm 2 Kilograms per metre squared of Sheet which is open LWM Longest part of diamond SWM Shortest part of diamond Expanded Aluminium Mesh Expanded Stainless Steel Mesh Spec 304/S15 Expanded Stainless Steel Mesh Spec 316/S31 Pre-Galvanised Steel Head Sales Office: PO Box 14, Longhill Industrial Estate (North), Hartlepool TS25 1PR, England. Tel: +44 (0) 1429 867388 Fax: +44 (1429) 866795 E-mail: sales@expamet.co.uk Web: www.expandedmetalcompany.co.uk For further information on other Expamet Company Products: Illustrations in this brochure are indicative of and Pattern. FENCING/SECURITY PRODUCTS Tel: +44 (0) 1429 867366 Fencing Security Cages www.expandedmetalfencing.co.uk TIMLOC EXPAMET BUILDING PRODUCTS Tel: +44 (0) 1405 765567 Cavity Trays Ventilation Systems DPC Systems Loft Access Doors www.expamet.co.uk EXPAMET BUILDING PRODUCTS Tel: +44 (0) 1429 866611 Metal Beads Laths Wall Starters Arch Formers Straps Joist Hangers Steel Lintels Metpost Steel Stud www.expamet.co.uk IRISH EXPAMET SALES OFFICE Westlink Industrial Estate, Kylemore Road, Ballyfermot, Dublin D.10. Tel: 00-3531 6265981 Fax: 00-3531 6267802 www.expamet@eirecom.net The company policy is one of continuous development, we therefore reserve the right to alter specifications, etc. without notice. Stock material may be collected from company depots for cash or by prior arrangement. Customers are advised to check availability of material. An Expamet International company Copyright The Expanded Metal Company Limited FM01344
www.expandedmetalcompany.co.uk
Conventional Mesh Expanded Aluminium Mesh Expanded Stainless Steel Mesh Spec. 304/S15 Expanded Stainless Steel Mesh Spec. 316/S31 Centre - Centre Strand 941MM 1.00 0.67 0.20 0.15 38 0.17/Lm 212 x Coil 957MM 1.50 0.92 0.22 0.15 52 0.19/Lm 313 x Coil 926S 3.18 1.95 0.79 0.46 19 1.89 610 x 1070 927S 3.175 1.81 0.254 0.152 72 1.08 420 x 10mtrs 901A 3.18 1.81 0.28 0.32 69 1.65 610 x 10mtrs 707S 4.75 2.38 0.56 0.46 53 2.64 1250 x 1250 220 5.84 3.50 0.79 0.60 55 3.30 1250 x 1250 601A 5.84 3.50 0.79 0.56 55 1.06 1250 x 1250 602A 5.84 3.39 1.17 0.56 31 1.63 1250 x 1250 227S 5.84 3.39 0.81 0.46 52 2.70 1250 x 1250 228S 5.84 3.39 1.22 0.56 28 4.44 1250 x 1250 Page 2
Edging Expanded Metal Size Thick Gap Standard Length Kg/m MILD STEEL EDGING SECTIONS Suitable for framing flattened Expamet up to and including 1.58 UF1 6.35 1.20 1.78 2490 0.13 OD split tube UF2 6.35 0.55 1.78 1905 0.07 UF3 12.70 0.90 1.78 2540 0.18 UF4 19.05 1.20 1.78 3810 0.38 UF5 31.75 1.20 1.78 3810 0.62 Suitable for framing flattened Expamet up to and including 3.18 UF6 12.70 0.90 3.30 2540 0.20 UF7 19.05 1.20 3.30 3810 0.38 UF8 31.75 1.20 3.30 3810 0.62 Suitable for framing conventional type Expamet expanded steel with strand widths of 2.39 or under. UF9 19.05 1.20 5.08 3810 0.38 Mild Steel L Edging Sections LF1 13 Ref. LF1 section for framing angled strand type expanded steel having strand widths of 4.75 or under. Standard length 2500. LF2 7 kg/m 0.88 30 kg/m 0.34 25 1.5 3 Ref. LF2 section for framing angled strand type expanded steel having strand widths of 2.40 or under and also flattened expanded steel. Standard length 2500. UF10 31.75 1.20 5.08 3810 0.62 Suitable for framing conventional type Expamet expanded steel with strand widths of 4.75 or under. UF11 19.05 1.50 10.16 3810 0.45 UF12 25.40 1.50 10.16 3810 0.63 UF13 25.40 2.95 10.16 3810 1.20 UF14 38.10 1.50 10.16 3810 0.91 UF15 38.10 2.95 10.16 3810 1.79 Suitable for framing conventional type Expamet expanded steel with strand widths of 6.09 or under. Can be used for framing expanded steel walkway grating ref. 2496. For full details see leaflet IP5. Edging Sections You can use Expamet edging section to transform standard sheets of mesh into a variety of functional products, adding value and enhancing appearance and appeal. Expamet edging section seals the edges of the mesh sheet giving a barrier for fixing, protecting or handling the finished sheets. Frames are frequently used on stairtreads and window guards. If you require advice on which edging section to use for your specific application, please contact our sales team Benefits Edging section is an economical way to make a mesh sheet into a functional panel. Fabrication is easy to perform and not time consuming, giving cost savings via our economically developed method. Features We offer a choice of 19 types of Edging Section in Mild Steel, which have been specifically developed for framing Expanded Metal Meshes. Edging Section can be used on both flattened and conventional / raised mesh.we offer a standard stock lengths, as well as a made to order capability, so non standard lengths are not a problem. UF16 14.29 1.50 12.70 3810 0.46 Suitable for framing 10g and 12g diameter welded mesh and expanded metal with strand widths up to 3.2 UF18 19.05 1.20 6.50 3810 0.42 UF19 31.75 1.20 6.50 3810 0.66 Page 15
Walkway Mesh Expanded Aluminium Mesh Internal Aperture LWA SWA Strand 2496 44.5 12.7 6.10 4.5 51 52.66 2440 x 1220 2496A 44.5 12.7 5.82 4.7 52 18.46 2500 x 1250 Centre - Centre 60.96 25.4 4896 79.4 23.8 6.35 4.5 65 41.14 2440 x 1220 Centre - Centre 121.92 33.86 4897 79.4 22.2 7.9 4.5 58 102.28 2440 x 1220 Centre - Centre 121.92 33.86 4899 73.0 19.0 9.53 6.00 50 78.10 1220 x 2440 Centre - Centre 121.92 36.85 4894 69.9 15.9 13.06 6.00 38 140.31 2265 x 1830 Centre - Centre 121.92 38.1 N7478 38.10 13.85 5.00 2.50 28 26.36 1220 x 1525 Page 14
Conventional Mesh Expanded Aluminium Mesh Expanded Stainless Steel Mesh Spec. 304/S15 AG indicates anodised gold Centre - Centre Strand 209 10.24 5.64 1.55 1.00 45 6.72 1250 x 1250 351A 10.24 5.64 1.55 0.90 45 2.09 1250 x 1250 351AG 10.24 5.64 1.55 0.90 45 2.09 1250 x 1250 203 10.24 5.64 0.79 0.60 72 2.04 1250 x 1250 199 14.29 5.64 1.17 1.00 59 5.08 1250 x 1250 196S 14.29 5.54 1.33 0.90 52 5.40 1250 x 1250 197S 14.29 5.54 1.33 0.70 52 4.20 1250 x 1250 0798 19.05 7.43 1.70 1.00 54 11.22 2500 x 1250 0798A 19.05 7.43 1.70 0.90 54 3.5 2500 x 1250 0798S 19.05 7.26 1.71 0.90 53 10.66 2500 x 1250 1196 28.58 9.52 1.98 1.20 58 11.66 2440 x 1220 1196A 28.58 9.52 1.98 1.20 58 4.22 2500 x 1250 1296 30.48 11.72 2.36 1.20 66 11.28 2440 x 1220 1296A 30.48 11.72 2.36 1.20 60 4.09 2500 x 1250 Page 3
Conventional Mesh Expanded Aluminium Mesh Expanded Stainless Steel Mesh Spec. 304/S15 Centre - Centre Strand 1299 30.48 11.72 1.19 1.20 80 5.72 2440 x 1220 1290S 30.48 11.72 1.83 0.90 69 7.03 2500 x 1250 1295 30.48 11.72 1.98 1.60 66 12.62 2440 x 1220 1295S 30.48 11.72 1.5 1.63 65 11.75 2500 x 1130 1294 30.48 11.72 2.36 1.60 60 15.06 2440 x 1220 1294A 30.48 11.72 2.36 1.60 60 5.47 2500 x 1250 1292 30.48 12.70 4.75 2.50 25 27.29 1220 x 1525 1598 38.10 16.93 2.31 1.20 73 7.65 2440 x 1220 1598A 38.10 16.93 2.31 1.20 73 2.78 2500 x 1250 1597 38.10 16.48 2.25 1.60 73 10.21 2440 x 1220 1597A 38.10 16.93 2.31 1.60 73 3.72 2500 x 1250 1595 38.10 16.93 3.08 1.60 64 13.60 2440 x 1220 1590S 38.10 16.48 1.91 1.50 77 8.55 2500 x 1250 Page 4
Shaped Mesh Pre-Galvanised Steel Centre - Centre Strand MINARET MINAR1 137.16 56.00 3.25 3.00 89 7.65 2340 x 1220 Not actual size PARALLEL STRAND 401 28.58 4.00 2.31 0.75 53 5.78 1250 x 1250 402 28.58 4.00 2.67 0.75 53 5.78 1250 x 1250 Centre - Centre LWA SWA Strand SQUARE 1601F 16.00 13.5 0.92 1.00 85 1.65 1250 x 1250 Page 13
Shaped Mesh Expanded Aluminium Mesh Expanded Stainless Steel Mesh Spec. 316/S31 Pre-Galvanised Steel Expanded Stainless Steel Mesh Spec. 304/S15 Internal Aperture LWA SWA Strand EXPERF 1302F 2.92 2.41 0.86 0.60 1.970 58 1250 x 1250 N6912F 4.60 2.00 1.67 0.7 36 3.50 1250 x 2500 N7486F 6.71 3.60 1.20 0.70 2.206 60 1250 x 2500 N7482F 6.40 3.13 1.40 1.20 53 1.52 1250 x 2500 N7484F 6.40 3.13 1.40 1.00 11.22 54 1250 x 2500 N6664F 5.00 3.22 1.22 0.70 57 2.37 1250 x 2500 N6659F 6.20 4.40 1.20 0.70 63 2.02 1250 x 2500 N7700F 12.00 11.80 2.50 1.50 3.570 70 1250 x 2500 N7699F 12.00 10.00 3.00 1.00 63 2.92 1250 x 2500 Centre - Centre Strand HEXAGON HEX1 19.05 9.00 1.22 1.20 74 3.76 1250 x 1250 HEX2 25.40 12.00 1.27 1.20 78 3.18 1250 x 1250 Page 12
Conventional Mesh Expanded Aluminium Mesh Centre - Centre Strand 1576 38.10 16.93 4.75 3.00 44 39.29 2440 x 1220 2096 50.80 22.58 2.34 1.20 79 5.80 2440 x 1220 2093 50.80 22.58 3.05 1.60 73 10.09 2440 x 1220 2091 50.80 22.58 2.52 2.50 78 13.00 2440 x 1220 2089 50.80 22.58 3.12 3.00 72 19.40 2440 x 1220 2089A 50.80 22.58 3.12 3.00 72 7.59 2500 x 1250 Page 5
Conventional Mesh Centre - Centre Strand 2088 50.80 22.58 3.89 3.00 66 24.08 2440 x 1220 3092 76.20 33.87 3.58 3.00 79 14.79 2440 x 1220 3398 85.73 39.33 2.59 2.50 94 7.71 2440 x 1220 Page 6
Flattened Mesh Internal Aperture LWA SWA Strand 3393F 77.47 27.18 6.53 2.82 68 21.19 2440 x 1220 3394F 69.85 37.08 5.49 2.16 77 11.81 1220 x 2440 3395F 76.96 32.77 3.81 1.85 81 8.33 2440 x 1220 Page 11
Flattened Mesh Expanded Aluminium Mesh Internal Aperture LWA SWA Strand 2076F 43.43 18.03 2.31 1.14 80 5.50 2440 x 1220 2077F 43.18 17.27 3.23 1.45 73 9.64 2440 x 1220 2077AF 42.93 17.02 3.12 1.45 73 3.40 2500 x 1250 2073F 42.93 14.22 4.60 2.69 61 25.57 2440 x 1220 { 14.38 18.30 x 915 2074F 39.12 18.29 4.72 2.74 66 22.47 1220 x 2440 { 12.64 915 x 1830 2074AF 40.64 17.78 4.04 3.00 79 8.81 1250 x 2500 N7622F 43.00 15.60 4.39 2.69 64 7.55 1220 x 2440 2489F 46.99 15.49 6.63 4.20 54 44.08 1220 x 2440 Page 10
Conventional Mesh Centre - Centre Strand 3396 85.73 40.64 3.18 3.00 84 10.92 2440 x 1220 4097 101.60 50.80 3.35 3.00 87 9.25 2440 x 1220 4599 114.30 39.33 4.58 3.00 77 16.31 2440 x 1220 Page 7
Flattened Mesh Expanded Aluminium Mesh Expanded Stainless Steel Mesh Spec. 304/S15 Internal Aperture LWA SWA Strand 706F 2.79 0.81 0.76 0.58 35 4.70 1250 x 1250 226F 3.81 2.03 0.79 0.58 56 3.30 1250 x 1250 228SF 3.00 1.00 1.22 0.56 29 4.44 1250 x 1250 217F 6.85 3.56 1.30 0.94 52 9.38 1250 x 2500 217AF 6.86 3.56 1.27 0.89 58 3.00 1250 x 2500 0794F 14.22 4.83 1.85 0.96 52 10.31 1250 x 2500 0794AF 13.97 4.83 1.80 0.89 57 3.22 1250 x 2500 0794SF 14.22 4.58 1.83 0.86 54 4.70 1250 x 1250 197SF 10.50 3.50 1.33 0.70 57 4.20 1250 x 1250 1276SF 25.00 8.00 1.98 1.09 67 9.15 2500 x 1250 Page 8
Flattened Mesh Expanded Aluminium Mesh Expanded Stainless Steel Mesh Spec. 304/S15 Pre-Galvanised Steel Internal Aperture LWA SWA Strand 1280F 24.38 7.11 2.39 1.14 57 10.8 2440 x 1220 1280AF 24.13 6.86 2.39 1.14 59 3.94 2500 x 1250 1282F 24.38 7.62 2.08 1.14 60 9.43 2440 x 1220 N0921F 25.15 8.64 1.65 0.94 70 5.58 2440 x 1070 1281F 24.38 7.87 2.06 1.47 66 12.11 2440 x 1220 1279F 23.11 5.84 3.20 1.52 48 18.66 2440 x 1220 1584F 32.77 10.92 3.18 1.50 63 13.12 2440 x 1220 1585F 33.53 12.45 2.34 1.14 73 7.35 2440 x 1220 1585AF 33.05 11.94 2.34 1.14 72 2.66 2500 x 1250 Page 9