Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without notice. Copyright 2012 Sizes and pipe connections CSF1 and CSF1T Stainless Steel Steam Filters Screwed BSP and NPT: ¼", ", ½", ¾", 1", 1¼", 1½", 2", 2½" and ". Flanged EN 1092 PN1: DN, DN10, DN1, DN20, DN2, DN2, DN40, DN0, DN and DN0. EN 1092 PN10: DN100, DN10 and DN200. ASME 10: ¼", ", ½", ¾", 1", 1¼", 1½", 2", 2½", ", 4", " and ". TI-P1-01 ST Issue 12 DN to DN0 DN100 to DN200 Description The CSF1 and CSF1T are horizontal, in-line high efficiency filters used to remove contaminate particles from steam systems. The filter housing is available in a choice of austenitic stainless steel (1.401) designated CSF1 or (1.4404) designated CSF1T. The DN to DN0 (¼" to ") housing is externally polished with an internal natural finish whereas the DN100 to DN200 (4" to ") housing will have a natural finish both internally and externally. The housings are constructed in two halves, DN to DN0 will be joined by a food industry fitting to DIN 111. DN100 to DN200 will be joined by bolts and nuts. Replaceable elements in sintered austenitic stainless steel are available with either 1, or 2 micron absolute rating. In some pipe sizes the element is available in a choice of low capacity designated 'L' and high capacity designated 'H'. Standards These products fully comply with the requirements of the European Pressure Equipment Directive 9 / 2 / EC and carry the mark when so required. The CSF1 and CSF1T, when fitted with a micron element are capable of removing 9% of particles 2 microns and larger in size, in accordance with the requirements for the production of culinary steam to A accepted practice number 09-0. Accepted in the U.S. Department of Agriculture for use in federally inspected meat and poultry plants. All materials meet the requirements as stipulated by the US FDA Regulations. Certification These products can be supplied with a modified housing in order to provide certification to EN 10204.1. Note: All certification / inspection requirements must be stated at the time of order placement. Page 1 of
Pressure / temperature limits Temperature C A B C D 1 10 E E Steam saturation 100 curve 0 0-20 0 E B C D.*.* 10 12 1 1 Pressure bar g 2 The product must not be used in this region. A-B-B Flanged PN10. A-C-C Maximum allowable pressure for the DN0H. A-D-D Screwed BSP or NPT, flanged PN1 and ASME 10. E-E-E Maximum operating limits for sizes DN100 to DN200. Body design rating PMA DN - DN (¼" - 2½") PN1 1 bar g Maximum allowable L version 1 bar g DN0 (") pressure H version 12 bar g DN100 - DN200 10 bar g Maximum allowable DN - DN0 1 C @. bar g TMA temperature DN100 - DN200 10 C @. bar g Minimum allowable temperature -20 C Maximum operating DN - DN0. bar g @ 1 C * PMO pressure DN100 - DN200. bar g @ 10 C DN to DN0 4 1 Maximum operating DN - DN0 1 C @. bar g TMO temperature DN100 - DN200 10 C @. bar g Minimum operating temperature 0 C PMX Maximum differential pressure bar g DN - DN (¼" to 2½") 2. bar g Designed for a maximum cold DN0 (") L version 2. bar g hydraulic test pressure of: H version 20. bar g DN100 - DN200 1. bar g 2 Materials No. Part Materials 1 Filter housing bowl Stainless steel 2 Filter housing head Stainless steel CSF1 1.401 CSF1T 1.4404 CSF1 1.401 CSF1T 1.4404 For sizes DN to DN0 EPM is supplied as standard. For sizes DN100 to DN200 Housing seal PTFE spirally wound gasket with stainless steel inner and outer rim support is supplied as standard - No other option is available. 4 Housing ring (DN - DN0) Stainless steel 1.401 CSF1-S filter element Stainless steel Filter element seal (2 off) EPM Plug Stainless steel asket P T F E Outer core 1.401 End cap 1.401 CSF1 1.401 CSF1T 1.4404 9 Flange Stainless steel 1.441 10 9 1 10 Bolts and nuts Stainless steel A2-0 (DN100 - DN200) DN100 to DN200 Page 2 of
Dimensions F E D (min) F E D (min) Screwed BSP and NPT A Flanged PN10, PN1 and ASME 10 A C C B B Dimensions / volume and weights (approximate) in mm, litres and kg Filter Size Dimensions A B C D E Vol. Weight (kg) without element Screwed Flanged Litres Screwed Flanged F PN ASME Ø Ø PN ASME ¼" DN 220 10 10 20 90 0 112 ¼" 0.0 2.0..1 " DN10 24 10 10 20 120 0 112 ¼" 0.0 2.1.4.2 CSF1 and CSF1T ½" DN1 24 10 10 20 120 0 112 ¼" 0.0 2.2..2 ¾" DN20 22 12 202 20 10 0 112 ¼" 0.4 2.4 4.4.9 1" DN2 29 12 212 24 4 10 12 ¼" 1.40.2..4 1¼" DN2 0 140 220 24 4 200 12 ¼" 1.0..2. 1½" DN40 10 24 294 94 200 104 14 ¼".00.2.9.0 2½" DN 40 21 0 10 0 129 1 ¼" 9.0.1 1. 1.9 2" DN0 4 10 20 29 94 20 104 14 ¼".0.2 9.9 9.9 CSF1L and CSF1LT " DN0 1002 240 1 111 0 129 1 ¼" 12.0 10.2 1.2 19.2 4" DN100 1040 40 40 190 0 219 40 1".00 0.0 0.0 " DN10 10 40 40 240 0 2 9 1".00.0.0 " DN200 10 0 0 29 0 40 1" 190.00 1.0 1.0 2" DN0 90 10 20 29 94 40 104 14 ¼" 4.0. 10. 10. CSF1H and CSF1HT " DN0 102 240 40 0 11 0 14 210 ¼" 1.0 1.2 19.9 21. 4" DN100 100 410 410 190 0 219 40 1" 4.00.0.0 " DN10 1410 40 40 24 0 24 44 1" 110.00 100.0 100.0 " DN200 10 0 0 29 0 40 1" 190.00 1.0 1.0 Page of
Capacities Saturated steam 1.0 bar g; DN0 CSF1 and CSF1T Flowrate kg/h Capacity correction factors for steam pressure Steam pressure bar g 0 1 2 4. Correction factor 0. 1.0 1. 2.0 2..0. 4.0 4. 4. Element size correction factors for filter element DN DN10 DN1 DN20 DN2 DN2 DN40 DN0L DN0H Size of unit ¼" " ½" ¾" 1" 1¼" 1½" 2"L 2"H Capacity correction factor 0.0 0.1 0.1 0.2 0.9 0.0 0. 1.00 1.0 Size of unit 0.0 Maximum recommended differential pressure Differential pressure bar ( x 100 = kpa ) DN DN0L DN0H DN100L DN100H DN10L DN10H DN200L DN200H 2½" "L "H 4"L 4"H "L "H "L "H Capacity correction factor 2.00 2.0 4.00.00.00 10. 1.00 21. 2. Selection example Select a steam filter for a flowrate of 0 kg / h with saturated steam pressure at 4 bar g. A micron rating is required with maximum 0.0 bar pressure drop allowed. Step 1: Divide the flowrate required by the capacity correction factor for the operating steam pressure. In this case, 0 kg / h is divided by 2. for an equivalent 40 kg / h flow. Step 2: From the capacity graph, select the micron rating required. Note where this line intersects the maximum pressure drop and go horizontally to read off the flowrate. In this case, the micron line meets the 0.0 bar pressure drop allowed at maximum flowrate of 100 kg / h. Step : Divide the equivalent flow calculated in step (1) by the maximum flowrate in step (2). Hence in this example, we have 40 / 100 =.4 factor. Step 4: From the element size correction factor table, select the nearest suitable conversion factor obtained in step () and select the appropriate element size. In the example DN0H CSF1 and CSF1T has a factor of 4.00. Note that if pressure drop must be minimized, always select the element based on a higher correction factor than that calculated. Filter element In steam / gas service, 100% of particles larger than the pore size chosen will be retained by the element. Note that the 1 micron element has an efficiency of 99.% based on 0.2 micron particles. Selecting a pore size smaller than required will result in reduced service life and higher pressure drop. The CSF1 and CSF1T elements can be cleaned by immersion in dilute hydrochloric acid, ultrasonic bath, clean water, or air, depending on the type of contamination. However, once the pressure drop across the filter (even after cleaning) reaches 0. bar the element should be replaced. Note: We strongly recommend that a spare filter element set is carried in stock. Page 4 of
Safety information, installation and maintenance For full details see the Installation and Maintenance Instructions (IM-P1-02) which is supplied with the product. How to order The following information must be specified when ordering a Spirax Sarco CSF filter: Steam flowrate kg/h Steam pressure bar Allowable pressure drop bar (0.0 bar maximum recommended) Housing material 1.401 or 1.4404 * Size DN or NPS (") Pipe connections EN, BSP or NPT Element rating 1, or 2 micron Housing seal / element seal material * Note: For DN0 and DN0 high capacity version denoted by 'H' and low capacity by 'L'. For a 1.4404 housing version, the suffix 'T' must be added to the nomenclature e.g. CSF1T. Supply The CSF1 and CSF1T are supplied in two parts: 1. The filter housing head and bowl with housing seal packed in one carton. 2. The filter element complete with filter element and two seals. (DN100 - DN200 CSF1 and CSF1T have multiple elements). Note: The job of the filter is to remove (and retain) unwanted contamination. In time, the filter element will become saturated. To ensure a minimum downtime, we recommend that a spare filter element set is ordered at the same time as the CSF1 and CSF1T filter housing. Example: 1 off Spirax Sarco DN20 CSF1 to pass 100 kg / h saturated steam at 4.0 bar g. Housing to be 1.401 having NPT connections with EPM seals. 1 off CSF1-S filter element having a micron rating. 1 off CSF1-S spare filter element set having a micron rating. Page of
Spare parts The spare parts available are shown in solid outline. Parts drawn in broken line are not supplied as spares. Available spares CSF1-S filter element kit, (2 off) Seal kit, (please see table below for quantities) Seal kit contents Unit size Housing seal Element seals () () DN - DN0 1 2 DN100 1 DN10 L 1 H 1 12 DN200 L 1 1 H 1 20 How to order spares Always order spares by using the description given in the column headed 'Available spares' and state the size and type of filter housing, filter element rating and housing / filter element seal material required. Example: 1 off micron CSF1-S filter element kit for a Spirax Sarco DN2 CSF1 clean steam filter, with EPM filter element seals. 10 4 Recommended tightening torques or Item N m mm 4 use C spanner As required DN - DN0 ¼" BSP As required DN100 - DN200 1"BSP As required DN100 A / F 0 M20 40 DN10L A / F 0 M20 2 10 DN10H A / F 0 M20 20 DN200 A / F M24 400 Page of