Vibration Condition Monitoring & Protection VIBRATION MONITORING SOLUTIONS AND SERVICES: PROXIMITY PRODUCTS SENSORS SWITCHES MONITORS PORTABLE METERS ACCELEROMETERS TRANSMITTERS SIGNAL CONDITIONERS Short Form Brochure 5.0 www.metrix1.com info@metrix1.com 281-940-1802
Product Overview Sensors ST6900 Series Compact Transmitters Signal Conditioners ST5484E Loop-powered, 4-20 ma Transmitters Loop-powered IT6810 Impact Transmitters Trendsetter TXR (Radial) or TXA (Axial) Transmitter TRANSMITTERS Accel Velocity Displacement 4-20 ma Mechanical Proximity Probes Extension Cables Electronic 5510 (Radial) or 5516 (Axial) Dynamic Signal 5533 Probe Drivers 4-20 ma on PRO Switches 5550 Switch Hardy HI 5800 PRO Series Switches 5534/5535 4-20 ma 5485C High Temp, Velocity Sensor SA6200A Accelerometers SV6300A Piezoelectric Sensor
Product Overview Systems HMI Portable Products PLC DCS AM3030 Single-Channel Alarm Monitor VM2800/VM3800 & 5500 Vibration Meters DATAWATCH 7100 configurable to 12 channels 6850 Impact Meter VIBRANT Full Spectrum Vibration Monitoring System Legacy System Vibration Condition Monitoring System Hardy Instruments HI3600 Monitor configurable to 16 channels, expandable to 32 DATAWATCH 8100 configurable to 48 channels Condition Monitoring Devices Cost-Effective Online Dedicated Channel Multi-Channel HI 803 & HI 813 Hardy Instruments Portable Shakers 8824 Fallbrook Dr. Houston, TX 77064 Tel: 281-940-1802 Fax: 713-559-9421 www.metrix1.com info@metrix1.com
Proximity Products Metrix features a complete line of Proximity solutions interchangable to Bently Nevada probes, cables and drivers. Our patented ProxMatch technology allows you to save money by not having to replace an entire system. Oil-Lubricated Fluid Film Bearing Machines: Centrifugal Pumps Turbo Compressors Steam and Gas Turbines Large Fans and Blowers Gear Box Shafts Generators Large Electrical Motors Proximity Probe and Cable Trendsetter Proximity Probe Transmitters 5533 Probe Driver 5510/5516 Signal Conditioners Trendsetter TXR (Radial) and TXA (Axial) Transmitters Two-wire loop-powered transmitter that combines an eddy current probe driver and signal conditioner in a single package Compatible with 4 major probe systems and easily factory-calibrated to non-standard shaft material Provides 4-20 ma signal proportional to vibration level or shaft axial position TXR5521 RPM Transmitters 4-20 ma proportional to shaft RPM Dynamic output for vibration Sensing to 177 C with proxmity probes Proximity Probes and Cables Latest technology design including gold hex connectors, Tefzel insulation, ProbeSeal and VerniGap for easy installation Extend life of installed transducers by replacing individual components Avoid mismatching probes and cables with ProxMatch Color Coding Protect critical machinery at lower cost Keep your installed base running longer to avoid obsolescence 5533 Probe Driver All proximity transducers have third party approvals and comply with API 670 specifications Rugged polymer with internal RFI/EMI spray shielding potted for long life Baseplate mounting holes are identical (requiring no field backplate drilling) and DIN rail mounting is optional Direct replacements for Bently Nevada Proximitor 7200, 3000 and 3300 Series BNC jacks for local analysis Proximitor and VALOX are registered trademarks of GE. 5510 (Radial) and 5516 (Position/Thrust) Gives output proportional to vibration or position Single channel signal conditioners Convert proximity transducer system to a transmitter for connection to a PLC or DCS Dynamic signal is available at the signal conditioner or remotely BNC connector for local analysis
Proximity Products ProxMatch Color Coding System Series 7200 / 10000 Metrix 10000 Series (Gold color) 5 M 5 M 9 M 9 M 5 M 7200 series label X Extension Cable 9 M 7200 series label Y X or Y Series 3300 & 3300XL Model Nos. MX3301XX (Baby Blue color) 5 M 5 M 9 M 9 M 5 M 3300 series label X Extension Cable 9 M 3300 series label Y X or Y Series 3309 RAM & NSv Model Nos. MX3309XX (Light Purple color) 5 M 5 M 7 M 7 M 5 M 3309 series label X Extension Cable 7 M 3309 series label Y X or Y Series 3000 Model Nos. 7386-01/2789 (no armor); 7386-01/4454 (w/armor) (White Color) 15 ft 15 ft 20 ft 20 ft 15 ft 3000 series label X in. Extension Cable 20 ft 3000 series label Y in. X or Y in.
Seismic Products Metrix offers a wide variety of seismic solutions for your vibration monitoring needs. This line includes transmitters, accelerometers, sensors and impact monitoring products. Velocity Sensors Cooling Towers Motors Pumps Fans Engines Blowers Gear Boxes Large Industrial Gas Turbines Furnace Fan Monitoring Hazardous Areas SV6300A Piezoelectric Sensor 5485C High-Temp Sensor (connector version) 5485C High-Temp Sensor (fi xed cable version) SV6300A 5485C Replace a moving coil velocity transducer with this solid-state sensor Consists of a temperature stabilized piezoelectric sensor and amplifier packaged in stainless steel case Immune to cross axis vibration, mount in any axis Provides high-level, low impedence output for connection to a 4-20 ma transmitter Provide accurate, repeatable vibration measurements over wide ranges of amplitude and frequency by employing zero friction coil suspension Self-generating, no power required Stainless steel housing Constructed for continuous operation at elevated temperatures Loop-Powered Vibration Transmitters Centrifuges Motors Compressors Pumps Engines Turbines Fans and Blowers Turbochargers Generators ST5484E Loop terminals with Independent Polarity (IPT) prevent incorrect wiring Temperature shock protected and widest frequency range available Available with flying leads, terminal block or ML-style connector ST5491E 4-20 ma proportional to velocity ST5484E Velocity Transmitter Built-in protection against temperature shock and ski slope problem Different mounting studs and high and low pass filters available Most stable detection circuit ST5491E Indicating Velocity Transmitter ST6900 Series Compact Transmitter ST6900 Series 4-20 ma proportional to acceleration (ST6911) 4-20 ma proportional to velocity (ST6917) Interfaces with PLC, DCS and 4-20 ma monitors Widest operating temperature in its class
Seismic Products Accelerometers Motors Gear Boxes Paper Machines Process Pumps Cooling Tower Fans Rotor Blade Pass Sensing Turbocharger Engine Vibration Gas Turbines - Aero & Marine Derivative - Industrial Frames High-Temp Furnace Fans Hot oil pumps SA6200A Industrial Accelerometer SA6350 High-Temp Accelerometer SA6200A SA6350 High-accuracy and repeatability yet priced within budget Eliminate false indications caused by high frequency noise rectified as low frequency using patented anti-ski slope technology Highest accuracy and widest frequency response Ideally suited for vibration monitoring of gas turbines and other high-temperature machines When used with 5535/5545 transmitter for accelerometer, a 4-20 ma signal proportional to acceleration or velocity is available Acceleration electrically isolated from the stainless steel case and cable Signal Conditioners Gear Mesh Monitoring on Gear Boxes Industrial Fans Motors & Generators Process Pumps Centrifuges Natural Gas / Diesel Engines Gas Turbines 5534/5544, 5535/5545 4-20 ma proportional to vibration level Significant savings over rack mount monitors Optional display, filter and/or galvanic isolation Sensor/cable input OK light 5534/5544, 5535/5545 Signal Conditioner and Transmitter Impact Transmitter and Meter Reciprocating Compressors Diesel and Recip Engines Pumps IT6810/IT6811/IT6812 Measures mechanical looseness such as loose rod nuts, broken or loose bolts, liquids in the process, excessive clearance in slipper, loose or worn pins, etc. 4-20 ma output, 2-pin MS connector Loop-powered, self-contained sensor Flying lead (Div 2 rated) or explosion-proof version (Div 1 rated) available IT6810 Impact Transmitter 6850 Meter Select transmitter s Pulse-Time, 4-20 ma or Peak Detect mode 6850 Impact Meter One device for transmitter checkout and setup, eliminates need for oscilloscope and voltmeters Battery-powered with digital display Waveform access through BNC connector
Vibration Switches Metrix offers both electronic and mechanical vibration switches with many of the features of high-end monitoring systems but at a lower cost. Our new state-of-the-art Electronic Switches are programmable to suit user needs. Electronic and Mechanical Switches Motors Pumps Blowers Centrifuges Fans Centrifugal Pumps Recip Engines Reciprocating Compressors Cooling Towers Electric Motors Natural Gas / Diesel Engines Heat Exchanger Fans Cooling Tower Fans PRO440 Electronic Switch PRO6000 Electronic Switch Hardy Instruments HI 5800 Switch 5550 Mechanical Switch PRO440 / PRO6000 Microprocessor design, USB or keypad configurable Multiple sensor type input Sensitivity is not affected by rotating speed of machinery Solid-state relay contacts used for alarm and/or shutdown HARDY INSTRUMENTS HI 5800 Adjustable vibration set point and time delay Local LEDs for alarm and OK indication Trip bypass for equipment start-up Failsafe operation through on-board delay 5550 Meets all requirements for mechanical switch in a single, affordable package Weatherproof and optional hazardous area rating Local and optional remote reset with startup delay SPDT or DPDT switch output contacts Portable Shakers Hardy Instruments portable shakers allow for compliance with OSHA 1910, ISO 9000 or API 670 by providing a means for verification of sensors and associated indicators. These units are programmable with built-in display and self-test features. For checking: - Accelerometers - Connectors and cabling - Non-contacting eddy current probe displacement systems Meet most of the frequency and amplitude requirements for compliance with API 670 Built-in reference accelerometer and indicator features calibration traceable to National Institute of Standards and Technology (NIST) - Transducers - Instruments - Monitoring systems or indicators Test seismic sensors up to 1.65 lbs (750 grams). Portable design allows for minimal disruption during system checks Hardy Instruments HI 803 and HI 813 Portable Calibration Shakers
Monitors Metrix DATAWATCH Monitors feature high-quality signal conditioning, a high-resolution color touch screen interface and onboard historicial review capability. The AM3030 Alarm Monitor consolidates excitation, display and protection into a single compact package. Our newest addition is the HARDY HI 3600, a fully-functional API 670 compliant monitor with extreme connectivity. Compressors Motors Pumps Blowers Fans Turbines Mixers Gears Centrifuges DATAWATCH 7100 and 8100 AM3030 Alarm Monitor Hardy Instruments HI 3600 Machine Monitor DATAWATCH 7100 & 8100 Provides high-quality signal trending with a sampling rate of 125 msec 6 to 48 inputs including TC & RTD 3 to 27 output relays with adjustable time delays Removable 256 MB flash memory AM3030 Three-color, 30 segment bar graph display with numerical indicator 4-20 ma process monitor with 2 or 4 adjust able relays Compatible with Metrix transmitters: ST5484E, TXR/TXA, ST6917 HARDY INSTRUMENTS HI 3600 Monitors 16 channels of vibration, impact and rod drop Expandable to 32 channels for additional measurements Full network integration into most plant networks (Profibus, Modbus TCP, ControlNet, DeviceNet) Portable Meters Metrix portable vibration meters are ideal for obtaining spot measurements of machinery vibration. Includes a carrying case so the meter is always ready for use. Motors & Generators Pumps Compressors Fans Piping Vibration Natural Gas Engines Supplement to FFT Analyzers Check Vibration Instrument Readings VM2800 & VM3800 Accurate, industrial standard piezoelectric accelerometer sensor Microprocessor-based measurements Backlit LCD readout in acceleration, velocity and displacement Display peak or RMS units 5500 VIBRA-CHECK VM2800/VM3800 Portable Meter 5500 Portable Meter Simply hold the probe tip against machine and observe reading on LCD indicator Includes reading hold feature Intrinsically-safe for use in hazardous areas Includes alkaline 9V battery; auto power-off extends battery life
Monitoring System The VIBRANT is an API-670 compliant machinery protection system. It integrates vibration monitoring with TTC controls for one complete solution. It connects to Metrix proximity probes, velocity transducers and seismic sensors. Steam & Gas Turbines Motors Engines Gear Boxes Blowers & Fans Designed for critical and essential machinery, including TSI. Field-configurable protection applications for alarming and shutdown. 40 dynamic channels, 22 process channels, 8 tachometer channels For Use With: Cooling Towers Compressors Generators Pumps VIBRANT Full-Spectrum Vibration Monitoring System Proximity Probes and Cables 5485C Sensors 5553 Prox Probe Driver SV6300A Piezoelectric Sensor SA6200A Accelerometer Service & Support Metrix offers the on-site support you require. Our specialists can provide as much or as little assistance as you may need. We perform a range of services to ensure the proper orientation of your instrumentation so that you receive reliable information to make decisions. Customized on-site classes on the proper installation and use of your equipment are available on your specific type of instrumentation. Visit our website at www.metrix1.com to schedule a training session. Metrix provides innovative solutions to OEMs, packagers and end users. Custom system design, integration and manufacture Corporate purchasing and service programs Procurement specifications Drawings (CAD), including complete electrical and mechanical documentation Installation from component to full turnkey Ongoing technical support For existing systems: physical audit of your plant s vibration monitoring points and equipment.
Company Profile History Metrix Instrument Co. was founded in 1965 in Houston, Texas. We were the first company in the market to manufacture 4-20 ma vibration transmitters, which greatly simplified vibration monitoring and reduced its cost. In 1992, we received our ISO 9001 quality systems certifications. Roper Industries (NYSE=ROP) acquired Metrix in 1995, and we began to expand our global presence. In 1998, Roper acquired PMC/BETA and combined it with Metrix, further expanding and strengthening the product line. Today, Metrix is a Limited Partnership of Roper Industries, a $2.1 billion industrial products company specializing in analytical instrumentation, industrial controls and fluid handling. Product Line We manufacture a complete line of equipment to measure and monitor vibration and provide early warning of potential machinery failure. Our products include proximity systems, transducers, seismic sensors, switches, transmitters, signal conditioners, monitors and portable meters. Industries Served Our products are used to monitor vibration on gas and steam turbines, motors, compressors, pumps, generators, gear boxes, paper machines and cooling towers. The Metrix product line is suitable for numerous industries, including air separation, chemical, oil & gas, pipelines, power generation, water/ wastewater treatment and many more.
For more information about our products and services, please contact your local representative, see our complete catalog at www.metrix1.com or contact us directly at 281-940-1802. Metrix Instrument Co. 8824 Fallbrook Dr. Houston, TX 77064 Tel: 281-940-1802 Toll-free: 1-800-METRIX-4 www.metrix1.com info@metrix1.com After Hours Technical Service: 713-702-8805 Short Form Brochure 5.0 Revised: July 2008 Customer Service Contacts Purchase Orders, Change Orders, RMAs E-mail: orders@metrix1.com Fax: 713-559-9417 Quotes/Applications/Technical Support E-mail: quotes@metrix1.com Fax: 713-559-9421 Order Status/Issues/Comments E-mail: cs@metrix1.com General Information, Literature Requests E-mail: info@metrix1.com Service/Repair E-mail: service@metrix1.com NOTE: ProbeSeal, VerniGap, ProxMatch, Trendsetter, VIBRA-CHECK and IPT are registered trademarks of Metrix Instrument Co., LP. Proximitor, 7200, 3000 and 3300 Series are registered trademarks of Bently Nevada. VIBRANT is a registered trademark of Compressor Controls Corporation. Local Representative Information