STB- 2 Installation and Operation Manual
Index 1 Unpacking your STB- 2 2 Installation 3 WIFI connectivity 4 Remote Control 5 Selecting Video Mode 6 Start Page 7 Watching TV / TV Guide 8 Recording & Playing back programs 9 Recordings list 10 Media Browser 11 Settings and Advanced Settings 12 Troubleshooting
Unpacking your STB- 2 Inside the box you will find the following: Set Top Box Remote control AA batteries Standard Definition Video Cable Do not use with HD TV Power supply Ethernet Cable (optional) HDMI Cable (optional) WIFI dongle (optional) Dongle HDMI Cable Remote Power supply Standard Def Cable
Installation 1. Plug the power supply into the wall. Do not plug it in into the box yet. 2. Put the batteries in the remote. 3. Plug the HDMI cable or Standard video cable into the box and into an available input on your TV. Switch your TV to the appropriate input. DO NOT use the standard cable if your TV has an HDMI port. 4. If you have the optional WIFI dongle, remove the cap and plug it into the USB port on the back of the box. If you are using the included Ethernet cable, plug one end of the Ethernet cable into the box and the other end into your Internet router. 5. Plug the power cable into your box. If you are using the Ethernet cable, and if your Internet is working and you have connected all the cables properly, the box will begin its boot sequence. This takes approximately 2 minutes to complete. Once the box is completely booted, it will load the main menu. Select UKTV and ALL. If the box does not boot, or if you get any other errors, then please see the troubleshooting section in this guide. If you are using the optional WIFI dongle, then please go to the WIFI connectivity page in this guide.
WIFI Connectivity If you have the UKTV WIFI dongle follow these instructions to connect the box to your WIFI network. 1. Plug USB WIFI dongle into USB port on the back of the Set Top Box. ONLY UKTV provided WIFI dongles will work on your set top box. 2. Plug power cable into box 3. At LOADING PORTAL, when it says press services button on your remote control press SETUP or SET button on the remote. This button is in the middle of the second row of buttons on your remote. If you miss this and your screen goes to Page loading error then press the blue F4 key to get to the settings page. 4. If a screen full of icons appears, Scroll to SETTINGS, press OK, if not jump to step 6. 5. Press SETUP button on the remote 6. Highlight NETWORK, press OK 7. Select WIRELESS, press OK 8. Select AUTO, press OK 9. Press ARROW DOWN on your remote, Highlight SCAN, press OK 10. Several networks may show up in the list. Select YOUR wireless network, and press OK 11. Scroll down to KEY or PASSPHRASE 12. Press the KB button on the remote. This button is the last key on the third row. 13. Using the virtual keyboard, type in your wireless network password pressing OK after you have selected each letter 14. Press the KB button on your remote to turn off the virtual keyboard 15. Scroll to OK, press OK on your remote 16. GO TO ADVANCED SETTINGS, scroll down to Time Zone and ensure it is set to GMT +00:00 London. Use the left and right arrows to adjust it. Then highlight OK and press OK. 17. Scroll down to REBOOT, press OK on your remote The box should then reboot, connect to the wireless network automatically and launch the TV.
Remote Control Your box may come with a programmable remote control. Instructions for programming are below as well as key instructions for both the programmable and non programmable remote comtrol.
Selecting Video Mode Your set top box is capable of displaying high definition video. By default, it is set to 1080i HD - 50 or 1080i - 60. If your TV does not have HDMI ports then you need to set your box into a lower resolution. Plug in the SD cable and go to the page on this instruction manual headed Nothing is coming up on the screen or MODE NOT SUPPORTED and follow the instructions to set your box into 480 NTSC or 576 PAL. You can find out what TV system type you need based on the country you live in by going to http://tinyurl.com/tvtype To upgrade back to HD follow these instructions IMPORTANT DO NOT SELECT A VIDEO OUTPUT MODE HIGHER THAN YOUR TV CAN DISPLAY. CONSULT YOUR TV MANUAL TO FIND OUT YOUR TV s HIGHEST VIDEO MODE. For customers in countries using the PAL system, set your box into PAL for SD or 1080-50 for HD For customers in countries using the NTSC system, set your box into NTSC for SD or 1080-60 for HD HD resolutions above 480 can only be achieved using an HDMI cable. From any screen, press the MENU button on the remote. 1. Press left arrow button on the remote until you SETTINGS is in the middle 2. Scroll to VIDEO, press OK 3. Select VIDEO OUTPUT MORE, press OK 4. Select desired video output mode. NTSC systems use - 60 modes, PAL systems use - 50 modes. Then press OK 5. Scroll to GRAPHIC RESOLUTION, press enter and select 1280x720 6. Scroll to OK, press OK 7. Scroll to RESTART, press OK 8. Select OK Your box will reboot into HD mode.
Start Page From the TV guide/preview window, press the MENU button on the remote. This will take you to the START PAGE. The start page is where you can select different applications. The applications available are TV This is the UKTV Everywhere TV application. Select ALL to view all channels. MEDIA BROWSER This icon allows you to play video and music from an external device such as a USB hard drive or thumb drive. YOU TUBE This icon takes you to YOUTUBE.COM where you can select and watch online videos from the You tube community INTERNET This icon takes you to a web browser where using a keyboard you can surf the Internet. RADIO This icon takes you to a listing of UK Radio stations available for your listening pleasure. SETTINGS This icon and the applications inside it are for box configuration. You can always go straight back to the TV from any screen by simply hitting the TV button on the remote. Start Page
Watching TV Switching channels The simplest way to switch channels is to either use the Channel +/- buttons on the remote or manually type in the channel number TV Guide / Preview window From any full screen TV channel, press the OK button on the remote. This will take you to the TV guide/preview window. From here you can scroll down to whatever channel you want to watch. There are multiple pages of TV channels. The program will launch in the preview window. To put it into full screen simply press OK. To see a list of what is on that channel for the next day, days or week press the right arrow button, highlight the day you want to see programming for and press OK. Press the left arrow button to return to the TV Guide Past/Present/Future Guide (PPF) From the TV guide/preview window press the INFO button on the remote. This will take you to the PPF (Past Present Future) Guide. From this guide, use the left, right, up and down keys that surround the OK button to scroll around the guide. The red line shows the present time, anything to the left is in the past. TV Guide PPF Guide
Recording & Playing back programs The box automatically records up to 2 weeks worth of programs on select channels. The channels that record are marked in the TV guide with yellow clocks next to the channel number. Playing programs from the past From the PPF guide you can select previously recorded programs by simply scrolling back in time on the guide, highlighting the program you want to watch and then pressing OK on the remote. Note: Due to program airing times, some programs may begin slightly before the recoding begins and the first few minutes are cut off. To watch the beginning of these programs, you will need to select the program preceding one you are wanting to watch and then fast forward to close to the end of that program to catch the beginning of the next program. You can do this by using the << >> II> and buttons on the remote. If the program you are watching gets slightly cut off at the end, then you will need to play the proceeding program on the guide to catch the end. You can also use the << >> II> and buttons to control the playback of any recorded program. The >> and << buttons between the channel and volume buttons skip back and forward 15 or 30 seconds. Once you have finished watching a prerecorded program, press EXIT on the remote to return to the menu. Recording programs It is not necessary to record programs on recordable channels as they automatically record anyway, however sometimes you may wish to mark a program to record in the future and save it to a USB stick for watching later on You can do this on recordable AND non- recordable channels. To record a future program plug a USB memory stick into the USB port on the front of the drive, then simply scroll forward in time to the program that you want to record, highlight it and press the red F1 key on the remote. A box will pop up on the screen asking to confirm the recording. Note your box must be switched on at the time of recording for the program to record.
You can also download previously aired programs on recordable channels to the USB stick. Simply highlight the program you wish to download, press the yellow F3 button and confirm the download. You can track the download progress by clicking on the DOWNLOADS tile in the main menu. You can also remove the USB drive and plug it into a laptop computer and watch the programs on there! Media Browser You can plug a USB storage device into the front USB port of your set top box and play back videos and music stored on the device through your TV. The box reads most popular formats including MP3 and AVI files as well as playing back programs from the box you have saved to it. To play back a file on your USB device, scroll over to MEDIA BROWSER in the start menu and press OK. From there you can select the directory and file that you wish to play. Settings and Advanced Settings In the main menu, scroll over to SETTINGS and press OK. You will see a sub menu of settings. DO NOT adjust the video, audio, network or servers settings. If you do your box will not work properly and may not work at all. In the advanced settings menu, you will see a buffer setting. Use the left and right arrows to increase and decrease the buffer. The buffer should be set somewhere between 1-4 do not set it any higher than 4 and only set it above 1 if you are having serious streaming issues. DO NOT alter ANY of the other settings on this screen.
Troubleshooting My picture is sometimes choppy or the screen goes black. Why? You are watching a live Internet feed directly from the UK. Any number of factors can cause video disruption. You must have a minimum 4MB Internet connection to ensure good quality video. Sometimes network traffic at peak times can cause video disruption. Freezing issues The streams your UKTV box receives come from a massive 10GB feed based out of multiple POP s around the world. Our system automatically routes your box to the closest POP. We have a 99.95% uptime on our feeds. If your box is experiencing freezing, then there is a 0.05% chance that it is a problem with our system. Our engineers monitor our feeds 24 hours a day both from the UK and the USA. If there is any maintenance issues, or planned disruption in service, we will always let you know by sending a message to your screen. If you are experiencing any freezing video that we have not let you know about it advance, then it is almost certainly a problem with your local system or Internet provider. Your UKTV box is only as good as the Internet it is connected to. We are a small company and take every single customers experience very seriously. We have worked very hard to build a system to bring UK television to people all over and world who otherwise cannot get it. It is virtually impossible to quantify just how complicated it is to design and build a system that makes it possible for you to watch UK television at the other side of the world. We want all of our customers to enjoy perfect UK television feeds, however some things are out of our control and can cause disruption. It is important to know that just because other services like Netflix and YouTube may stream OK and your UKTV box may not does not mean that the problem lies with your UKTV service, nor does having a very fast Internet connection bare any relevance. You can have a 30MB connection and your UKTV box may still freeze because of packet loss or inadequate routing provided by your ISP. Streaming video tests the limits of any Internet connection and is the most bandwidth intense product available. NO streaming video system works perfectly 100% of the time, but the system we have built is as close to perfect as there is. If you are experiencing freezing issues, especially at peak times of day (6PM- 10PM and on weekends) then it is an absolute certainty that the problem lies with your ISP. If you are experiencing consistent freezing at all times, then there is a 100% certainty that it is a problem with your Internet provider.
Steps you can take to help alleviate freezing issues. 1. Make sure your WIFI router is less than 30ft away from your UKTV box. To check to see if the problem is with the WIFI connection, connect the UKTV box directly to your router with an Ethernet cable. Move the router and the UKTV box closer together if possible. Cheap wifi routers are not equipped to handle transmitting video. Any N150 routers simply will not work for this application. We recommend 600 or 900 series routers. 2. You MUST have an Internet connection that is 4MB or higher. Certain ISP s, share their internet connections and at peak times your internet connection speed will drop as more people in your area go online. There is nothing we can do to help this situation. 3. Run a test on your Internet connection by going to www.pingtest.net and look at the results. ANY packet loss on your line with cause disruption in your feeds. 4. Reboot your cable modem and router. Sometimes this helps. If you are experiencing these issues, this is a problem with your local Internet provider or the setup in your house. You should contact them and tell them about the issue. This problem is outside of our control and we cannot help you with this problem. I can t get my box to connect. I get a PORTAL ERROR. Portal error means your box is not connecting to your router or your router is not connecting to the internet. Check to make sure your Internet is working. Restart your router, and check your WIFI connection if you are using a WIFI dongle. Make sure you have entered the correct password and that your box is connected to your router. Your password is case sensitive. If you know your internet is working and you keep getting portal error then it is almost certainly because your WIFI settings are wrong, usually the password.
Nothing is coming up on the screen or MODE NOT SUPPORTED First make sure your box has a blue light on the front. Make sure your video input on your TV is set to the corresponding input that the box is connected to. If it is, unplug the power from the box and plug it back in. If still nothing then follow these instructions EXACTLY as written 1. Unplug power from box. 2. While holding down the MENU button on the remote, plug the box back in 3. Hold the MENU button down for 5 seconds after plugging in. If you are still seeing nothing then go to step 4, if a menu appears, go to step 5. 4. Press the red F1 button on the remote. You may have to press it twice, until a blue screen appears with a menu on it. If the menu says TV TYPE at the top then skip to step 5, if it says UPGRADE MENU, then press the right arrow on the remote and wait for the next menu to appear. 5. Using the up, down, left, right arrows on the remote, press the right arrow button until TV type is set to 1080i- 60 if you are using an HDMI cable or NTSC if you are using the standard cable. If you are in a country that uses the PAL system then set TV type to 1080i- 50 6. Arrow down to Graphic res, press the right arrow button until it is set into 1280x720 if you are using an HDMI cable or 720x480(576) if you are using the standard cable 7. Arrow down to Exit and Save, press the right arrow button to save and then press OK to confirm NEVER go into any of the other settings on this menu page or change them. You WILL render your box useless AND you will void your warranty. Still can t get it to work? Email our tech support team. The email address is located on our website.