AUTOMATIC POLYPROPYLENE STRAPPING MACHINE TP-60D TP-60L TP-60D3 TP-60L3 OPERATION MANUAL & SPARE PARTS LIST Original Instruction READ ALL INSTRUCTIONS BEFORE OPERATING THIS PRODUCT
Explanations for Each Model NO. : TP-60D:Standard Single Phase Model TP-60D3:Standard Three Phase Model TP-60L:Low Table Single Phase Model TP-60L3:Low Table Three Phase Model
PART I CONTENTS. Safety Instructions... () Before Operating... (2) During operating... (3) After operating... (4) Signs... (5) Maintenance... 2 (6) Storage... 2 (7) Other Reminders... 2 (8) Attention... 2 2. Construction and Function of Units... 3 3. General Safety Remarks... 5 () Basic Operation... 5 (2) Basic Safety Precautions... 5 (3) Safety Instructions Governing Specific Operational Phases... 5 (4) Warning of Electrical Dangers... 6 (5) Grounding Instructions Shall Include the Following... 7
4. Machine Information... 8 () Areas of Application and Machine Description... 8 (2) Technical Data... 9 (3) Control Panel... (4) Electric Control Unit... 2 5. Operating the Machine... 3 () Operation Space... 3 (2) Installation of Arch Unit (For TP-60D)... 4 (3) How to Load P.P. Strap... 6 (4) How to Operate... 8 6. Adjustments... 9 () Heater temperature mechanism... 9 (2) Feed and take-up mechanism... 20 (3) How to adjust LS3, LS2... 2 (4) Amount of strap in Accumulator Box... 23 7. Maintenance... 25 8. How to Safely move the Machine... 26 9. Troubleshooting... 27 0. Wiring Diagram... 28
. Safety Instructions () Before Operating a. Read the instruction manual. b. Wear eye protection and safety gloves before operating this machine. Eye protection must be worn Safety gloves must be worn Ear-protector must be worn c. Verify that the power line voltage is correct. d. The machine must be properly grounded to avoid a shock hazard. All wiring must be in accordance with local wiring standards. e. The strapping machine can only be operated with polypropylene (P.P.) strapping; do not use polyester (PET) strapping or polyethylene (PE) cord strap. (2) During operating a. The weight of the package cannot exceed 00 kg (220 lbs), b. The size of the package should not be less than 30mm (width) 20mm (high) (5. 0.79 ). c. Check if the machine emits any smokes or unusual sound when it is running. d. Keep away from the inside of the arch while the machine is operating; do not put your hands or body into the arch when the machine is running. (3) After operating a. Remove dust and dirt from the unit; pay particular attention to the interior of the arch. b. Turn off the power when the machine is not in use. (4) Signs Caution! Electric Shock Hazard Caution! Hot! Do not touch! - -
Warning for danger! Do not put your hands or body into arch working area when machine is operating. (5) Maintenance a. Turn off the power before removing either of the top covers. b. The heater tongue is very hot; do not touch it. (6) Storage a. The store room must be dry. b. Do not expose the machine to extreme cold or heat environment. c. Place the machine on an even floor in order to avoid any distortion. (7) Other Reminders a. A operation manual must remain attached to the machine at all times. b. Do not alter the equipment or circuitry unless authorized to do so by the manufacturer. (8) Attention When the machine arrives in your warehouse, you need to use a forklift to take it off from the pallet. If you could go down to the bottom side of the machine, you would see an indication sticker as follows: (TP-60L) Follow this sticker and lead the teeth of a forklift to that indicated position. After making few distance adjusting, you then could drive the teeth in and take off the machine. - 2 -
2. Construction and Function of Units a. TP-60D Strapping head unit This unit is the most important part of the machine for cutting and sealing of P.P. 2 Bandway unit This is the arch track through which P.P. strap forwards or reverses. 5 Body frame unit 4 Reel unit Holds the strap coil. (If strap core is 280mm, you can take off the center drum to have core size 200mm.) 6 Electric control unit 8 Auto strap feeding unit 3 Accumulator unit This unit accumulates the quantity of strap required for smooth feeding into the chute track. - 3 -
b. TP-60L 4 Reel unit Holds the strap coil. (If strap core is 280mm, you can take off the center drum to have core size 200mm.) 3 Accumulator unit This unit accumulates the quantity of strap required for smooth feeding into the chute track. 2 Bandway unit This is the arch track through which P.P. strap forwards or reverses. 8 Auto strap feeding 6 Electric control unit 5 Body frame unit Strapping head unit This unit is the most important part of the machine for cutting and sealing of P.P. strap. - 4 -
3. General Safety Remarks () Basic Operation The machine is only to be operated when in good running condition and in accordance with the instructions provided in the operation manual. Operators must be trained in proper operation and safety of the equipment. The machine may only be operated in accordance with its designated use. (2) Basic Safety Precautions In addition to the instructions for operation, the user is to be instructed in all generally applicable legal or mandatory regulations relevant to safety or the environment. Long hair, loose-fitting garments, or jewelry can be a safety hazard. These items must be secured prior to equipment operation. Use protective equipment whenever appropriate or when required by law. Carefully observe all safety instructions and warnings attached to the machine. Keep safety labels clean and legible. People that are being trained to operate or service the equipment must be supervised by experienced personnel. Any electrical work performed on the equipment must be conducted by a skilled electrician or under the supervision of a skilled electrician. All work must observe good electrical engineering practice and follow safety rules and local wiring standards. (3) Safety Instructions Governing Specific Operational Phases Avoid unsafe operation of the equipment. The machine is only to be operated when it is in good running order. Only operate the equipment in a safe manner; all protective and safety devices must be in place and fully functional. This includes removable safety devices, emergency shut-off equipment, noise-protection devices and exhaust fans. The machine is to be checked for damage and defects at least once each work shift. Any changes, including the working behavior of the machine, are to be reported immediately. If necessary, the machine is to be stopped and locked-out immediately. In case of a malfunction, the strapping machine is to be immediately stopped and locked-out until the fault has been eliminated. - 5 -
Before starting the strapping machine, make sure that the area is clear and safe. Operating personnel need to be briefed before executing special operations and maintenance work; this work needs to be done with the proper supervision. Always check and tighten connections after maintenance or repair. After completing maintenance or repair, all safety devices must be replaced and checked for functionality before operating the equipment. To minimize the environmental impact, all consumables and replaced parts must be disposed of safely. Before starting the machine, check that the accessories have been stowed away safely. Avoid operating the machine in a fashion that could upset its stability. (4) Warning of Electrical Dangers Electrical Energy Immediately remove power to the machine in case of trouble in the electrical system. Replace a fuse with one with the same style and ratings; pay particular attention to matching the specified current. Any electrical work performed on the equipment must be conducted by a skilled electrician or under the supervision of a skilled electrician. All work must observe good electrical engineering practice and follow safety rules and local wiring standards. Inspect the electrical equipment of the machine at regular intervals. Tighten any loose connections. Check wiring for scorch marks; replace scorched wiring and determine and correct the reason for the overheating. When working on live equipment, ensure that a second person is available to cut power in case of an emergency. When appropriate, secure the working area with safety tape and a warning sign. Use insulated tools for electrical work. Before working on high-voltage assemblies, turn off the power supply. Carefully discharge the supply cable and short-circuit any energy-storage components such as capacitors. If the equipment was moved, carefully refit and refasten all parts removed for transport before reapplying power. Before moving the machine, remember to disconnect the power cable. - 6 -
(5) Grounding Instructions Shall Include the Following This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock. This product is equipped with a cord that has a grounding wire and an appropriate grounding plug. The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances. If repair or replacement of the cord or plug is necessary, connect the ground wire to the ground terminal of the plug. The wire with green insulation (with or without yellow stripes) is the grounding wire. Check with a qualified electrician or service person if the grounding instructions are not clear or if in doubt about the proper grounding of the machine. Do not modify the plug provided; if it will not fit the power outlet, have the proper outlet installed by a qualified electrician. DANGER! Improper installation of the grounding can result in electrocution. - 7 -
4. Machine Information () Areas of Application and Machine Description This plastic strapping machine can be used for all types of strapping applications with package sizes of 30 mm(width) 20 mm(height) and up. This machine is particularly suitable for heavy packaged goods as well as printed products, boxes, etc. Machine Description Automatic plastic strapping machine for use with polypropylene strapping Extra tough construction Simple, safe and user-friendly operation Automatic feeding-system Automatic strap-end detection Loop ejection Mobile, with large table area and high capacity strap reel Table surface made of stainless steel Strap tension adjustable from soft to extremely high Environment Information The strapping machine shall be installed in the following conditions: Supply voltage: 0.9 -. nominal supply voltage Source frequency: 0.99 -.0 nominal frequency Ambient temperature: 5 C - 40 C (4-04 ). Relative humidity: not exceed 50% at 40 C. Please provide a suitable illumination around the machine for safety operation. - 8 -
(2) Technical Data a. TP-60D Sealing method : Heat Strap width : 8 mm to 2 mm (3/8" - /2") Strap thickness : 0.55 mm up to 0.75 mm (0.022" - 0.03") Strap reel diameter : 200 mm (8" nominal) Width : 430 mm (56.3") Depth : 620 mm (24.4") Table height : 80 mm (3.9") Electrical connection : AC 0V/220V/230V/240V (50/60Hz), PH AC 220V/380V/400V (50/60Hz), 3PH Weight : 220 kg (485 lbs.) Noise emission : 83 db (A) Ambient temp : 5 ~ 40 (4 ~04 ) - 9 -
b. TP-60L Sealing method : Heat Strap width : 8 mm to 2 mm (3/8" - /2") Strap thickness : 0.55 mm up to 0.75 mm (0.022" - 0.03") Strap reel diameter : 200 mm (8" nominal) Width : 880 mm (74") Depth : 620 mm (24.4") Table height : 40 mm (6.") Electrical connection : AC 0V/220V/230V/240V (50/60Hz), PH AC 220V/380V/400V (50/60Hz), 3PH Weight : 235 kg (58. lbs.) Noise emission : 83 db (A) Ambient temp : 5 ~ 40 (4 ~04 ) - 0 -
(3) Control Panel TP-60D Start Switch This is the switch to start a strapping operation. A strapping cycle is completed only after actuation of this switch. (Indicator for strap goes to ready position) 2 Reset switch This is the switch to activate auto strap feeding. In addition, it is used for troubleshooting. If the strap is mis-fed, you can push this button to solve the problem. 3 selector switch While selector switch is placed to the position, the machine will automatically strap the package when it is placed on the table and passes the chute arch, if the package remains under the arch, the strapping cycle will continue. While the selector switch is placed to the position, after positioning the package under the arch, push the "START" switch, then one strap will be applied. TP-60L 4 Tension Adjustment Knob External adjustment of strap tension by step-by-step rotation of this knob. - -
(4) Electric Control Unit Timer, T 30 : T timer determines the time necessary for strap take-up. While setting, please test with the minimum sized package. Normally, Timer T is set at about 0.5 second, but may have to be adjusted depending on arch size & actual package size. TP-60D TP-60L TP-60D3 TP-60L3-2 -
5. Operating the Machine () Operation Space Keep the area (A) and (B) free for the operator. The area (A) is necessary for operation strapping machine and the area (B) is necessary for changing the strap or adjusting strap amount in the accumulator. B A - 3 -
(2) Installation of Arch Unit (For TP-60D) - 4 -
a. Take the upper table, 5 off. b. Take the LH bandway 2 off. 6 TMS, M5 8 PC 8 TMS, M6 8 2PC HBS, M8 5 4PC 2 SW, M8 4PC 8 PW, M8 (A) 4PC c. Slide the arch unit 3 into the fixing brackets 4 and fix both sides of the arch frame with 2 8. * Please note that is imperative to open the flaps of RH bandway 5 to protect them when installing the arch unit in. (open the flaps, before inserting the arch unit in) d. Set the LH bandway 2, with 6 and 8. d-. Please note that the arch bandway (refer Fig. A) should be positioned between LH bandway and its fixing bracket. d-2. Please set the LH bandway 2 closely to 7 guiding angle (PART NO. T6-2-2260). d-3. Push the 6 Band guide Spring Bracket backward to check if B will be automatically turned open. If so, the installation is OK. e. Position the upper table 5 onto the machine body. - 5 -
(3) How to Load P.P. Strap a. TP-60D Ensure that the power switch is turned off before loading P.P. strap. Step Place a strap coil on the reel drum in according to the arrow direction as indicated on the Reel Out Circular 9. After placing it, put the Reel Out Circular on the strap coil and tighten it by the Reel Nut Handle 0. Step 2 Thread the tip of P.P. strap into the Band Guide Roller. After that, push it through the Free Angle 2. At this moment, twist the strap so that the inside part of the P.P. strap turns out downward and outside surface touches on the roller. See the drawing. Step 3 Insert P.P. strap into the Pool Feed Shooter 3, pushing the lever 4 down and feed P.P. strap about -2 cm beyond Pool roller 5 Step 4 Turn on the power supply switch, and then push Reset Switch 7. After about 4 seconds, the strap will automatically go into the arch and pool. - 6 -
b. TP-60L Ensure that the power switch is turned off before loading P.P. strap. Step Place a strap coil on the reel drum in according to the arrow direction as indicated on the Reel Out Circular 9. After placing it, put the Reel Out Circular on the strap coil and tighten it by the Reel Nut Handle 0. Step 2 Thread the tip of P.P. strap into the Roller Bracket Ass'y 2. After that, thread it through the Band Guide Roller. Step 3 Insert P.P. strap into Pool Feed Shooter 3 and turn Accumulator Main Roller 4 until the P.P. strap about -2 cm beyond the Main Roller 4. Step 4 Turn on the power supply switch, and then push Reset Switch 7. After about 4 seconds, the strap will automatically go into the arch and pool. - 7 -
(4) How to Operate a. Turn on the Main power switch (make a 90-degree clockwise turn). The front door will be locked at the same time. [If you want to open the front door, turn off the main power switch first (make a 90-degree counterclockwise turn). In this way, the operator can open the front door without risk.] (See drawing below) b. Wait for about 3 minutes until the heater element reaches its required operating temperature. c. Place a package in the middle of the chute. d. Set tension with Tension Adjustment Knob (VR)(see page part I P 4 ) e. Push start switch (see page part I P ) or actuate foot pedal switch to start strapping. The strapping operation is repeated if the start switch is pushed again. - 8 -
6. Adjustments () Heater temperature mechanism Set the knob to position 3 or 4 Adjust the heater temperature by selecting a value between and 6. Choose the suitable temperature, bearing in mind the environmental conditions of the machine. If the heater temperature is too high or too low, a proper seal will not be obtained. Gradually increase or reduce the heater-knob value until obtaining an optimum seal. - 9 -
(2) Feed and take-up mechanism If this unit is not correctly adjusted, strap feed and take-up will become irregular. Normally, this unit is set to accept P.P. strap with the thicknesses of 0.55mm-0.75mm. If a different strap thickness is used, adjust the section marked by a circle in the drawing so that the clearance between the Upper Roller Spring 23 and the Upper Shaft Spring Hook 24 should be the thickness of the strap you are using. Strap can only be taken up properly if this unit is precisely adjusted. (If not, strap will be sealed before being tightened around the package) Moreover, strap will leave the chute arch track when feeding into it if there is no clearance. a. Check if the control unit returns to its original position. Insert the strap between Feed Roller 22 and Upper Feed Roller 2. b. Loosen 2 Bolts 27 holding the right-hand Block Arm 25 with the Press Arm Shaft 26. Press Arm Shaft can then easily be moved by hand. c. Adjust so that there is a clearance between the Upper Roller Spring 23 and the Upper Shaft Spring Hook 24 the same as the thickness of the strap you are using. d. Tighten 2 Bolts 27. The thickness of the strap you are using - 20 -
(3) How to adjust LS3, LS2 Figure : LS-3 Home Position Figure - M6 screw Cam Follower Tension Cam Figure : LS-2 Figure 2- Take-up Cooling Time Feeding Figure shows the correct position for LS3 Proximity Sensor 3 and the Limit Switch Cam 32 while the machine is in home position. The machine will stop as soon as the LS3 Proximity Sensor 3 detects that Limit Switch Cam 32 is activated. At this time, the Cam Follower 4 must stop at the corner position on the Tension Cam 42 as shown in figure -. If not, please adjust according to the following instructions. Adjustment If Cam Follower 4 stops before the correct position: a. Loosen the two M6 screws and turn the Cam Roller slightly clockwise, then tighten the M6 screws. b. Reset the machine and allow it to cycle again to ensure that the Cam Follower 4 stops at the correct position. c. If the problem has not been eliminated, please repeat the "Step One" until the Cam Follower 4 stops at the correct position. - 2 -
If Cam Follower 4 stops beyond the correct position: Please also loosen the M6 screws but turn the Cam Roller slightly counterclockwise until the Cam Follower 4 stops at the correct position. Figure 2 shows the correct position for LS2 Proximity Sensor 33 against the lobes of the Limit Switch Cam 34 while machine is running. When LS2 Proximity Sensor 33 detects Lobe A of the activated running Limit Switch Cam 34, the machine will stop about 0.3 seconds so that the machine can switch to take-up. In the meantime, Cam Follower 4 has to stay on the corner position of the Tension Cam 42 as shown in figure 2-. If the Cam Follower is not at the correct position, please make the same adjustment as for LS3. - 22 -
(4) Amount of strap in Accumulator Box a. TP-60D The machine has already been set in its Accumulator Box. However, some adjustment may be required, depending on the actual quality or thickness of the strap used. If adjustment is necessary, proceed as shown in the following drawing. a-. In case that there is an insufficient amount of strap in the Accumulator Box, loosen the Nut 27 and turn the Screw Bolt 28 counterclockwise. a-2. In case that there is an excessive amount of strap in the Accumulator Box, loosen the Nut 27 and turn the Screw Bolt 28 clockwise. - 23 -
b. TP-60L Fig A: If you have moved the LS4 Micro Switch to the left up to the bottom but you still do not have enough P.P. strap in the accumulator box, you can loosen nut E and turn the bolt D C.C.W. increase the amount of P.P. strap in the accumulator box. Finally tighten the nut E. T7-3-090 Micro Switch (LS4) M6 Screw T7-3-0200-24 -
7. Maintenance Warning: Before any maintenance or repairs on the machine, set the Main Power Switch to "O" (OFF). Wait about 5 minutes for cooling down the heater to avoid burns with this area. () Cleaning and Lubrication The high reliability and long service life of the strapping machine will depend on regular cleaning and maintenance. ATTENTION! All the important strap transport components, such as the feeding rollers and the strap guides, must be kept free from oil and grease. (lubricant) The lubricant has to be non-resinous. The lubricant is SAE 30 (2) Maintenance Only use original spare parts supplied by manufacturer. Daily: Use air gun to clean the circled positions (nearby the cutters, strap guide and accumulating feeding rollers) daily Remove plastic residue in the machine. - 25 -
Monthly :( or 50,000 strapping cycles) Clean both sides of heater plate and polish with fine sandpaper if necessary ATTENTION: Make sure the welding plate is cool first!! Check supporting and cam rollers of strapping head for easy movement. The slide table must be moved back to home position automatically by the spring tension. Be sure to clean any debris in the tension jaw. 6 Months:(or 300,000 strapping cycles) Check heater plate, replace and readjust it if necessary. Check strap cutter in strapping head, replace it if necessary. Check that connector at wiring loom to printed circuit board is firmly fixed. Make machine ready for operation. Strap one bundle manually several times, paying attention to mal-functions, repeat procedure. Check strap accumulating function. Do proper adjustments to accumulating feeding pressure or the reel brake belt year :( or 600,000 strapping) Replace deflection roller if it shows visible changes. In case of loud noise at bearings: locate them, replace the bearings. Get machine ready for operation again, strap one bundle manually several times, paying attention to malfunctions. NOTE: Any other service must be performed by an authorized service representative. 8. How to Safely move the Machine a. Before moving the machine, be sure to unplug the power cord and put it in safe place to avoid any damage. b. Moving the machine by holding the Reel Guard to pull or push the machine. Note: Don t move the machine by pulling or pushing the arch unit. - 26 -
9. Troubleshooting () Incorrect strap feed and take-up Probable Causes Remedy a. Incorrect strap threading direction on a. Reload strap correctly (see page 6) reel holder b. Incorrect loading of strap b. Check if strap is twisted in loading section (see page 6) c. Strap gets in between strap coil and c. Reload strap Reel Flange d. Insufficient or excessive strap d. Adjust amount of strap accumulated (see page 23) e. Dust and strap residues in Feed Unit e. Check and clean unit f. Strap end is split f. Adjust Cutter Tension Spring or change cutter g. Loose strap at Reel Unit g. Adjust or change Brake Tension Arm Spring h. Strap jumps out of arch track h. Adjust F/R mechanism (see page 20) i. Poor quality of strap i. Cut off the damaged part of strap or change the roll j. Improper positioning of package on j. Replace the package in the center of the Table Top Sealing Head (2) Strap unsealed Probable Causes Remedy a. Wire inside or outside of Heater is a. Check wire or change Heater broken, loose or out of connect b. Improper setting of temperature b. Adjust Heater Temperature (see page 9) c. Value set at Tension knob is too high c. Adjust Tension Knob (see page ) or increase weld cooling time (3) Improper strap tensioning Probable Causes Remedy Value set for Timer T is too short Adjust Timer T (see page 2) - 27 -
0. Wiring Diagram - 28 -
- 29 -
- 30 -
- 3 -
- 32 -
- 33 -
- 34 -
- 35 -
- 36 -
- 37 -
- 38 -
- 39 -
- 40 -
- 4 -
- 42 -
- 43 -
PART II CONTENTS. Strapping Head Unit 2. Bandway Unit 3 3. Accumulator Unit 45 4. Reel Unit 59 5. Body Frame Unit 70 6. Electric Control Group 98 7. Auto Strap Feeding Unit 09
STRAPPING HEAD UNIT T6--9005 T6--90052 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6--9005 T6--9005S T6--90052 T6--90052S T6--90053 T6--90053S T6--90054 T6--90054S T6--9006 T6--9006S T6--90062 T6--90062S T6--90063 T6--90063S T6--90064 T6--90064S Strapping Head Unit (For TP-60D, 2mm) Strapping Head Unit (For TP-60D, 2mm)(Stainaless Steel Model) Strapping Head Unit (For TP-60D, 9mm) Strapping Head Unit (For TP-60D, 9mm)(Stainaless Steel Model) Strapping Head Unit (For TP-60D3, 2mm) Strapping Head Unit (For TP-60D3, 2mm)(Stainaless Steel Model) Strapping Head Unit (For TP-60D3, 9mm) Strapping Head Unit (For TP-60D3, 9mm)(Stainaless Steel Model) Strapping Head Unit (For TP-60L, 2mm) Strapping Head Unit (For TP-60L, 2mm)(Stainaless Steel Model) Strapping Head Unit (For TP-60L, 9mm) Strapping Head Unit (For TP-60L, 9mm)(Stainaless Steel Model) Strapping Head Unit (For TP-60L3, 2mm) Strapping Head Unit (For TP-60L3, 2mm)(Stainaless Steel Model) Strapping Head Unit (For TP-60L3, 9mm) Strapping Head Unit (For TP-60L3, 9mm)(Stainaless Steel Model) T6--0003 Cam Group SEE PAGE 4-2 -
STRAPPING HEAD UNIT T6--9005 T6--90052 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 2 T6--20020 Slide Table Group SEE PAGE 7 T6--20020S Slide Table Group (Stainaless Steel SEE PAGE 7 Model) 3 T6--30000 Press Group SEE PAGE T6--30000S Press Group (Stainaless Steel Model) SEE PAGE 4 T6--40000 Heater Group SEE PAGE 6 5 T6--5003 Strapping Head Group (For TP-60D) SEE PAGE 9 T6--50032 Strapping Head Group (For TP-60L) SEE PAGE 9 6 T6--60003 Tension Group SEE PAGE 2 T6--60003S Tension Group (Stainaless Steel SEE PAGE 2 7 T6--70002 Feed Group (For TP-60D/TP-60L, SEE PAGE 25 2mm) T6--70002S Feed Group (For TP-60D/TP-60L, SEE PAGE 25 2mm) T6--70003 Feed Group (For TP-60D/TP-60L, SEE PAGE 25 9mm) T6--70003S Feed Group (For TP-60D/TP-60L, SEE PAGE 25 9mm) T6--70004 Feed Group (For TP-60D3/TP-60L3, SEE PAGE 25 2mm) T6--70004S Feed Group (For TP-60D3/TP-60L3, SEE PAGE 25 2mm) T6--70005 Feed Group (For TP-60D3/TP-60L3, SEE PAGE 25 9mm) T6--70005S Feed Group (For TP-60D3/TP-60L3, 9mm) SEE PAGE 25-3 -
- CAM GROUP T6--0003 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6--00 Tension Cam 2 T6--020 Cam Shaft End Plate 3 T6--03 Limit Switch Cam (LS2) 4 T6--042 Limit Switch Cam (LS3) 6 KYA070720 Key, 7 7 20 2 7 T6--07 Gear Box Pulley 8 T6--08 Limit Switch Bracket 9 BR6205ZZ Bearing, 6205ZZ 2 0 T6--0200 V-Belt (A26) T6-6-080 Magnet Brake 4 T6--000 Gear Box 42 T6--2000 Cam Ass'y SEE PAGE 6 5 HBS0845H HBS, M8 45 (H) 4 52 HBS0825 HBS, M8 25 53 HBS062 HBS, M6 2 2 54 HSS060G HSS, M6 0 (G) 6 55 PW08B PW, M8 (B) 4 56 SW08 SW, M8 5 57 SW06 SW, M6 2 6 SW04 SW, M4 4 62 PMS0408 PMS, M4 8 4-5 -
-2 SLIDE TABLE GROUP T6--20020 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6--20020 Slide Table Group T6--20020S Slide Table Group (Stainless Steel Model) T6--200 Slide Table Frame 2 T6--2020 Slide Table Frame Shaft 4 T6--204 Slide Table Back Adjuster 5 T6--2050 Slide Table Stopper 6 T6--2063 Slide Table T6--2063S Slide Table 7 T6--2070 Strap Guide 8 T6--2080 Flap Connecting Spring Bracket 9 T6--2098 S.F.S. Ass'y T6--2098S S.F.S. Ass'y 0 T6--3070 Press Arm End Plate T6--20220 Slide Table Spring Hook 2 T6--20230 Slide Table Tension Spring 4 BR6304ZZ Bearing, 6304ZZ 2 5 T6--20250 Cam Follower, KR22 LL 6 ER5 Snap Ring, E-5 2 7 T6--203 Support 8 T6--20323 Lever 9 T6--20340 Bracket 20 T6--2035 Spring 2 T6--20450 Bushing 27 T6--20372 Spring 4 T6--2000 Strap Guide Arm Ass'y SEE PAGE 0 50 HBS0630 HBS, M6 30 5 HBS025H HBS, M0 25 (H) 52 HBS0830 HBS, M8 30 53 HBS0650H HBS, M6 50 (H) 2 54 HBS0620N HBS, M6 20 (N) 4 HBS0620S HBS, M6 20 4 55 HBS0625 HBS, M6 25 3 56 HSS080G HSS, M8 0 (G) 2 57 TMS060 TMS, M6 0 2 60 PW08A PW, M8 (A) 6 PW06A PW, M6 (A) 4-8 -
-2 SLIDE TABLE GROUP T6--20020 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 63 SW06 SW, M6 7 64 HBS066 HBS, M6 6 65 HBS0408 HBS, M4 8 6 66 TMS042 TMS, M4 2 2 67 HN08 HN, M8 7 SW04 SW, M4 9 72 SW04S SW, M4 74 NTE04 NTE, M4 76 HN06 HN, M6 4 77 SW03 SW, M3 2 80 TA-07 Return Spring 8 T6--2090 Sensor Plate 82 T6--20920 Loop-eject Lever 83 T6--20930 Loop-eject Plate T6--20930S Loop-eject Plate 84 HN03 HN, M3 2 85 HN04 HN, M4 3 86 HN04S HN, M4 87 PMS046 PMS, M4 6 88 PMS042 PMS, M4 2 95 FMS0508 FMS, M5 8 2 FMS0508S FMS, M5 8 2 96 T6--20840 Detector Plate 97 T6-2-030 LH Bandway Stop Spring - 9 -
-3 PRESS GROUP T6--30000 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6--30000 Press Group T6--30000S Press Group T6--300 Press Arm Shaft 2 T6--3020 Cutter Tension Spring Hook 3 T6--3030 Upper Roller Spring 4 T6--3040 Upper Shaft Spring Adjuster 5 T6--3050 Press Tension Spring 3 6 T6--3060 Cutter Tension Spring 7 T6--3070 Press Arm End Plate 8 BR6304ZZ Bearing, 6304ZZ 2 9 ER5 Snap Ring, E-5 4 T6--3000 RH, Block Arm Ass'y SEE PAGE 3 T6--3000S RH, Block Arm Ass'y (Stainless Steel SEE PAGE 3 Model) 42 T6--32000 Center Block Arm Ass'y SEE PAGE 4 T6--32000S Center Block Arm Ass'y (Stainless SEE PAGE 4 Steel Model) 43 T6--33000 LH, Block Arm Ass'y SEE PAGE 5 5 HBS0620 HBS, M6 20 52 HSS065G HSS, M6 5 (G) 2 53 TMS060 TMS, M6 0 2 54 HN08 HN, M8 2 55 HN06 HN, M6 2 56 PW08A PW, M8 (A) 57 PW06B PW, M6 (B) 2 58 SW06 SW, M6-2 -
-4 HEATER GROUP T6--40000 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6--400 Heater Cover 2 T6--4020 Heater Crank Spring 3 T6--4030 Heater Slider Guide (L) 4 T6--4040 Heater Slider Guide (R) 5 T6--4050 Heater Crank Shaft 6 ER5 Snap Ring, E-5 2 7 T6--4070 Heater Stopper 8 LA-40002 Label 2 T6-6-0920 Activated Carbon Filter (Option) 22 T6-6-0930 Nipple (Option) 23 T6-6-0940 Smoke-Exhaustion Pipe (Option) 24 T6-6-0970 Fan (For Smoke)(Option) 4 T6--4000 Heater Ass'y 42 T6--42000 Heater Crank Ass'y SEE PAGE 8 43 T6--43000 Smoke-exhaustion system, with activaed carbon filter. (Option) T6--4300 Smoke-exhaustion system, without activated carbon filter. (Option) 5 HSS060G HSS, M6 0 (G) 2 52 HBS066 HBS, M6 6 4 56 TMS0408 TMS, M4 8 4-7 -
-5 STRAPPING HEAD GROUP T6--5003 T6--50032 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6--5003 Strapping Head Group (For TP-60D) T6--50032 Strapping Head Group (For TP-60L) T6--5000 Strapping Head Frame 2 T6--50 Band Width Block 5 HBS0820 HBS, M8 20 (For TP-60D) 4 HBS0825 HBS, M8 25 (For TP-60L) 4 52 HBS0620 HBS, M6 20 54 PW06B PW, M6 (B) 55 SW08 SW, M8 4 56 PW08C PW, M8 (C) 4 6 T6--50660 Bracket 63 HBS062 HBS, M6 2 2 64 SW06 SW, M6 2-20 -
-6 TENSION GROUP REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6--60003 Tension Group T6--60003S Tension Group T6--60 Tension Arm Shaft 2 T6--6020 Tension Arm Spring 4 T6--6040 Tension Arm Spacer 2 6 T6--6060 Tension Arm Spring Hook L-Type 7 BRHK256 Bearing, HK256 2 8 ER5 Snap Ring, E-5 2 T6--60003 BRIR20257 Bearing, IR20257 2 2 SP0680 Spring Pin, 6 80 4 T6--600 Tension Arm Ass'y SEE PAGE 23 42 T6--62000 Tension Jaw Ass'y T6--62000S Tension Jaw Ass'y (Stainless Steel Model) 53 HN08 HN, M8 2 54 PW08B PW, M8 (B) - 22 -
-6- TENSION ARM ASS'Y T6--600 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 9 T6--6290 Support Plate 20 T6--6300 Collar 3 2 T6--600 Bracket Set 22 T6--60 Motor (M5-) Set 48 SW08 SW, M8 49 SW05 SW, M5 7 50 MB504 Metal Bushing, 504 5 HSS080G HSS, M8 0 (G) 2 52 HN08 HN, M8 56 HN06 HN, M6 57 THS0540 THS, M5 40 3-24 -
-7 FEED GROUP T6--70002 T6--70003 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6--70 V-Belt M-22 (For TP-60D/TP- 60L) T6--702 V-Belt M-23 (For TP-60D3/TP- 60L3) 4 T6--7002 Feed Ass'y (For 2mm) SEE PAGE 27 T6--7002S Feed Ass'y (For 2mm)(Stainless Steel SEE PAGE 27 Model) T6--7003 Feed Ass'y (For 9mm) SEE PAGE 27 T6--7003S Feed Ass'y (For 9mm)(Stainless Steel SEE PAGE 27 Model) 42 T6--72000 Upper Adjusting Weight Ass'y SEE PAGE 30 (For TP-60D) T6--72030 Upper Adjusting Weight Ass'y (For TP-60L) SEE PAGE 30-26 -
-7- FEED ASS'Y T6--7002 T6--7003 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6--7002 Feed Ass'y (For 2mm) T6--7002S Feed Ass'y (For 2mm)(Stainless Steel Model) T6--7003 Feed Ass'y (For 9mm) T6--7003S Feed Ass'y (For 9mm)(Stainless Steel Model) 2 T6--723 Upper Feed Roller (For 2mm) T6--724 Upper Feed Roller (For 9mm) 3 T6--730 Upper Feed Roller Shaft 4 T6--740 Feed Roller T6--740S Feed Roller 5 T6--750 Lever Holder 6 T6--760 Feed Roller Pulley 7 T6--770 Feed Shooter (For 2mm) T6--770S Feed Shooter (For 2mm)(Stainless Steel Model) T6--77 Feed Shooter (For 9mm) T6--77S Feed Shooter (For 9mm)(Stainless Steel Model) 8 T6--780 Feed Shooter Cover T6--780S Feed Shooter Cover (Stainless Steel Model) 9 T6--793 Upper Feed Roller Set (For 2mm) T6--794 Upper Feed Roller Set (For 9mm) 0 BR628ZZ Bearing, 628ZZ BR6202ZZ Bearing, 6202ZZ 4 2 RR24 Snap Ring, H-24 2 3 RR35 Snap Ring, H-35 4 4 ER2 Snap Ring, E-2 5 HBS0645H HBS, M6 45 (H) 2 HBS0645HS HBS, M6 45 (H)(Stainless Steel 2 Model) 52 HBS066 HBS, M6 6-28 -
-7- FEED ASS'Y T6--7002 T6--7003 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 53 HSS065G HSS, M6 5 (G) 54 HSS060G HSS, M6 0 (G) 2 55 PMS060 PMS, M6 0 2 PMS060S PMS, M6 0 2 56 HN06 HN, M6 2-29 -
2 BANDWAY UNIT T6-2-90000 T6-2-90007 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-2-90000 Bandway Unit (For 2mm) T6-2-90000S Bandway Unit (For 2mm)(Stainless Steel Model) T6-2-90007 Bandway Unit (For 9mm) T6-2-90007S Bandway Unit (For 9mm)(Stainless Steel Model) T6-2-00 Bandway Group (For 850W, 2mm) SEE PAGE 32 T6-2-0 Bandway Group (For 850W, 9mm) SEE PAGE 32 T6-2-020 Bandway Group (For 650W, 2mm) SEE PAGE 32 T6-2-02 Bandway Group (For 650W, 9mm) SEE PAGE 32 T6-2-040 Bandway Group (For 050W, 2mm) SEE PAGE 32 T6-2-04 Bandway Group (For 050W, 9mm) SEE PAGE 32 T6-2-050 Bandway Group (For 250W, 2mm) SEE PAGE 32 T6-2-05 Bandway Group (For 250W, 9mm) SEE PAGE 32 T6-2-060 Bandway Group (For 450W, 2mm) SEE PAGE 32 T6-2-06 Bandway Group (For 450W, 9mm) SEE PAGE 32 T6-2-070 Bandway Group (For 650W, 2mm) SEE PAGE 32 T6-2-07 Bandway Group (For 650W, 9mm) SEE PAGE 32 T6-2-080 Bandway Group (For 850W, 2mm) SEE PAGE 32 T6-2-08 Bandway Group (For 850W, 9mm) SEE PAGE 32 2 T6-2-20003 Chute Arch Group SEE PAGE 38 T6-2-20003S Chute Arch Group (Stainless Steel Model) SEE PAGE 38-3- -
2- BANDWAY GROUP T6-2-00 T6-2-0 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-2-00 Bandway Group (For 850W, 2mm) T6-2-0 Bandway Group (For 850W, 9mm) T6-2-020 Bandway Group (For 650W, 2mm) T6-2-02 Bandway Group (For 650W, 9mm) T6-2-040 Bandway Group (For 050W, 2mm) T6-2-04 Bandway Group (For 050W, 9mm) T6-2-050 Bandway Group (For 250W, 2mm) T6-2-05 Bandway Group (For 250W, 9mm) T6-2-060 Bandway Group (For 450W, 2mm) T6-2-06 Bandway Group (For 450W, 9mm) T6-2-070 Bandway Group (For 650W, 2mm) T6-2-07 Bandway Group (For 650W, 9mm) T6-2-080 Bandway Group (For 850W, 2mm) T6-2-08 Bandway Group (For 850W, 9mm) 4 T6-2-000 RH Bandway Ass'y (For 2mm) SEE PAGE 34 T6-2-00 RH Bandway Ass'y (For 9mm) SEE PAGE 34 T6-2-00 RH Bandway Ass'y (Only 650W, 2mm) SEE PAGE 34 T6-2-0 RH Bandway Ass'y (Only 650W, 9mm) SEE PAGE 34 42 T6-2-2000 LH Bandway Ass'y (For 850W, 2mm) SEE PAGE 35 T6-2-200 LH Bandway Ass'y (For 850W, 9mm) SEE PAGE 35 T6-2-200 LH Bandway Ass'y (For 650W, 2mm) SEE PAGE 35 T6-2-20 LH Bandway Ass'y (For 650W, 9mm) SEE PAGE 35 T6-2-2020 LH Bandway Ass'y (For 050W, 2mm) SEE PAGE 35 T6-2-202 LH Bandway Ass'y (For 050W, 9mm) SEE PAGE 35 T6-2-2030 LH Bandway Ass'y (For 250W, 2mm) SEE PAGE 35 T6-2-203 LH Bandway Ass'y (For 250W, 9mm) SEE PAGE 35 T6-2-2040 LH Bandway Ass'y (For 450W, 2mm) SEE PAGE 35 T6-2-204 LH Bandway Ass'y (For 450W, 9mm) SEE PAGE 35 T6-2-2050 LH Bandway Ass'y (For 650W, 2mm) SEE PAGE 35 T6-2-205 LH Bandway Ass'y (For 650W, 9mm) SEE PAGE 35 T6-2-2060 LH Bandway Ass'y (For 850W, 2mm) SEE PAGE 35 T6-2-206 LH Bandway Ass'y (For 850W, 9mm) SEE PAGE 35 5 TMS0608 TMS, M6 8 4-33 -
2- BANDWAY GROUP T6-2-00 T6-2-0 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 53 HBS0650 HBS, M6 50 54 TMS0508 TMS, M5 8 56 HN06 HN, M6 2 57 PW06A PW, M6 (A) 2-33- -
2--2 LH BANDWAY ASS'Y T6-2-2000 T6-2-200 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-2-2000 LH Bandway Ass'y (For 850W, 2mm) T6-2-200 LH Bandway Ass'y (For 850W, 9mm) T6-2-200 LH Bandway Ass'y (For 650W, 2mm) T6-2-20 LH Bandway Ass'y (For 650W, 9mm) T6-2-2020 LH Bandway Ass'y (For 050W, 2mm) T6-2-202 LH Bandway Ass'y (For 050W, 9mm) T6-2-2030 LH Bandway Ass'y (For 250W, 2mm) T6-2-203 LH Bandway Ass'y (For 250W, 9mm) T6-2-2040 LH Bandway Ass'y (For 450W, 2mm) T6-2-204 LH Bandway Ass'y (For 450W, 9mm) T6-2-2050 LH Bandway Ass'y (For 650W, 2mm) T6-2-205 LH Bandway Ass'y (For 650W, 9mm) T6-2-2060 LH Bandway Ass'y (For 850W, 2mm) T6-2-206 LH Bandway Ass'y (For 850W, 9mm) 3 T6-2-230 LH Bandway Flap Pin 2 (For 650W~050W) LH Bandway Flap Pin 3 (For 250W~450W) LH Bandway Flap Pin 4 (For 650W~850W) 4 T6-2-240 LH Bandway Flap Spring (For 650W~050W) LH Bandway Flap Spring 2 (For 250W~450W) LH Bandway Flap Spring 3 (For 650W~850W) 5 T6-2-250 LH Bandway Flap Spring 6 T6-2-280 Pillar (For 450W~850W) TMS0508 TMS, M5 8 (For 450W~850W) - 36 -
- 37 -
2-2- ARCH ASS'Y T6-2-2003 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-2-2003 Arch Ass'y T6-2-2003S Arch Ass'y T6-2-200 Arch Frame (For 850W 600H) T6-2-200S Arch Frame (For 850W 600H) 2 T6-2-2020 Arch Bandway (For 850W 600H) 3 T6-2-2046 Arch Cover, Front (For 850W 600H) T6-2-2046S Arch Cover, Front (For 850W 600H) 4 T6-2-2047 Arch Cover, Rear (For 850W 600H) T6-2-2047S Arch Cover, Rear (For 850W 600H) 5 T6-2-2050 Upper Guide Rail (For 850W) T6-2-2050S Upper Guide Rail (For 850W) T6-2-205 Upper Guide Rail (For 050W) T6-2-205S Upper Guide Rail (For 050W) T6-2-2052 Upper Guide Rail (For 250W) T6-2-2052S Upper Guide Rail (For 250W) T6-2-2053 Upper Guide Rail (For 450W) T6-2-2053S Upper Guide Rail (For 450W) T6-2-2054 Upper Guide Rail (For 650W) T6-2-2054S Upper Guide Rail (For 650W) T6-2-2055 Upper Guide Rail (For 850W) T6-2-2055S Upper Guide Rail (For 850W) T6-2-2059 Upper Guide Rail (For 650W) T6-2-2059S Upper Guide Rail (For 650W) - 40 -
2-2- ARCH ASS'Y T6-2-2003 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 6 T6-2-2060 RH Side Guide Rail (For 600H) T6-2-2060S RH Side Guide Rail (For 600H) T6-2-206 RH Side Guide Rail (For 800H) T6-2-206S RH Side Guide Rail (For 800H) T6-2-2062 RH Side Guide Rail (For 000H) T6-2-2062S RH Side Guide Rail (For 000H) T6-2-2063 RH Side Guide Rail (For 200H) T6-2-2063S RH Side Guide Rail (For 200H) T6-2-2069 RH Side Guide Rail (For 400H) T6-2-2069S RH Side Guide Rail (For 400H) 7 T6-2-2070 LH Side Guide Rail (For 600H) T6-2-2070S LH Side Guide Rail (For 600H) T6-2-207 LH Side Guide Rail (For 800H) T6-2-207S LH Side Guide Rail (For 800H) T6-2-2072 LH Side Guide Rail (For 000H) T6-2-2072S LH Side Guide Rail (For 000H) T6-2-2073 LH Side Guide Rail (For 200H) T6-2-2073S LH Side Guide Rail (For 200H) T6-2-2079 LH Side Guide Rail (For 400H) T6-2-2079S LH Side Guide Rail (For 400H) 8 T6-2-2080 Corner Guide Rail, Upper 4 T6-2-2080S Corner Guide Rail, Upper (Stainless 4 Steel Model) 9 T6-2-2090 Corner Guide Rail, Lower (LH) T6-2-2090S Corner Guide Rail, Lower (LH) - 4 -
2-2- ARCH ASS'Y T6-2-2003 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 0 T6-2-20200 Corner Guide Rail, Lower (RH) T6-2-20200S Corner Guide Rail, Lower (RH) T6-2-2020 Guide Rail Hinge ()(For 850W 600H) 2 T6-2-20220 K-Type Guide Rail Hinge Shaft 2 (For 850W 600H) 3 T6-2-20230 Guide Rail Hinge (2) 4 T6-2-20240 Guide Rail Hinge Shaft (For 850W 600H) 5 T6-2-2250 Arch Guide Rail Spring (For 850W 600H) 6 T6-2-2260 Guiding Angle, LH Front T6-2-2260S Guiding Angle, LH Front (Stainless Steel Model) 8 T6-2-2280 Guiding Angle, RH Front T6-2-2280S Guiding Angle, RH Front (Stainless Steel Model) 9 T6-2-2290 Guiding Angle, RH Rear T6-2-2290S Guiding Angle, RH Rear (Stainless Steel Model) 24 T6-2-20340 Back Guide Plate, Upper (For 850W) T6-2-20340S Back Guide Plate, Upper (For 850W) T6-2-2034 Back Guide Plate, Upper (For 050W) T6-2-2034S Back Guide Plate, Upper (For 050W) T6-2-20342 Back Guide Plate, Upper (For 250W) T6-2-20342S Back Guide Plate, Upper (For 250W) T6-2-20343 Back Guide Plate, Upper (For 450W) T6-2-20343S Back Guide Plate, Upper (For 450W) T6-2-20344 Back Guide Plate, Upper (For 650W) T6-2-20344S Back Guide Plate, Upper (For 650W) - 42 -
2-2- ARCH ASS'Y T6-2-2003 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-2-20345 Back Guide Plate, Upper (For 850W) T6-2-20345S Back Guide Plate, Upper (For 850W) T6-2-20349 Back Guide Plate, Upper (For 650W) T6-2-20349S Back Guide Plate, Upper (For 650W) 25 T6-2-2350 Back Guide Plate, Side (For 600H) 2 T6-2-2350S Back Guide Plate, Side (For 600H) 2 T6-2-235 Back Guide Plate, Side (For 800H) 2 T6-2-235S Back Guide Plate, Side (For 800H) 2 T6-2-2352 Back Guide Plate, Side (For 000H) 2 T6-2-2352S Back Guide Plate, Side (For 000H) 2 T6-2-2353 Back Guide Plate, Side (For 200H) 2 T6-2-2353S Back Guide Plate, Side (For 200H) 2 T6-2-2359 Back Guide Plate, Side (For 400H) 2 T6-2-2359S Back Guide Plate, Side (For 400H) 2 26 T6-2-2360 Back Guide Plate, Corner Upper 2 T6-2-2360S Back Guide Plate, Corner Upper 2 27 T6-2-2370 Back Guide Plate, LH Lower T6-2-2370S Back Guide Plate, LH Lower 28 T6-2-2380 Back Guide Plate, RH Lower T6-2-2380S Back Guide Plate, RH Lower 29 PN04 PN, 4 2 PN04S PN, 4 2-43 -
2-2- ARCH ASS'Y T6-2-2003 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 52 TMS0508S TMS, M5 8 (SUS) 8 53 TMS0408 TMS, M4 8 72 54 HBS0440H HBS, M4 40 (H) 55 HN04 HN, M4 56 SW04 SW, M4 6 LA-40005 Label 2 62 LA-4070 Label - 44 -
3 ACCUMULATOR UNIT T6-3-9000 T6-3-90023 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-3-0007 Accumulator Group (For TP-60D, SEE PAGE 47 2mm) T6-3-0007S Accumulator Group (For TP-60D, SEE PAGE 47 2mm) T6-3-0008 Accumulator Group (For TP-60D, SEE PAGE 47 9mm) T6-3-0008S Accumulator Group (For TP-60D, SEE PAGE 47 9mm) 2 T6-3-2000 Accumulator Box Group (TP-60D, SEE PAGE 52 2mm) T6-3-2000S Accumulator Box Group (TP-60D, SEE PAGE 52 2mm) T6-3-20002 Accumulator Box Group (TP-60D, SEE PAGE 52 9mm) T6-3-20002S Accumulator Box Group (TP-60D, SEE PAGE 52 9mm) 3 T6-3-30004 Accumulator Box Group (TP-60L, SEE PAGE 54 2mm) T6-3-30004S Accumulator Box Group (TP-60L, SEE PAGE 54 2mm) T6-3-30005 Accumulator Box Group (TP-60L, SEE PAGE 54 9mm) T6-3-30005S Accumulator Box Group (TP-60L, 9mm) SEE PAGE 54-46 -
3- ACCUMULATOR GROUP T6-3-0007 (For TP-60D) T6-3-0008 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-3-0007 Accumulator Group (For 2mm) T6-3-0007S Accumulator Group (For 2mm) T6-3-0008 Accumulator Group (For 9mm) T6-3-0008S Accumulator Group (For 9mm) T6-3-00 Balance Bar (For 2mm) T6-3-0 Balance Bar (For 9mm) 2 T6-3-020 Accumulator Balance Spring 3 T6-3-030 Accumulator Adjusting Bolt T6-3-030S Accumulator Adjusting Bolt (Stainless Steel Model) 5 T6-3-050 Accumulator Spring Adjusting 6 T6--7240 Spring 7 LA-50200 Label (Direction) 8 T6-3-08 V-Belt, M-27 9 T6-3-090 Balance Bar Spacer (Only 2mm) 0 T6-3-0200 Twist Stopper 4 T6-3-2000 Accumulator Ass'y (For 2mm) SEE PAGE 50 T6-3-200 Accumulator Ass'y (For 9mm) SEE PAGE 50 5 HBS0620 HBS, M6 20 4 HBS0620S HBS, M6 20 4 53 HBS066 HBS, M6 6 (For 2mm) 2 HBS062 HBS, M6 2 (For 9mm) 2 54 PMS035 PMS, M3 5 55 HN08 HN, M8 3 HN08S HN, M8 3 56 HN03 HN, M3 58 PW06C PW, M6 (C) 4 PW06CS PW, M6 (C) 4-48 -
3- ACCUMULATOR GROUP T6-3-0007 (For TP-60D) T6-3-0008 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 59 SW03 SW, M3 60 SW08 SW, M8 6 SW06 SW, M6 6 SW06S SW, M6 6 62 T6-3-032 Cover 63 PW05 PW, M5 2 64 SW05 SW, M5 2 65 HBS050 HBS, M5 0 2 66 PW06A PW, M6 (A) 2-49 -
3-- ACCUMULATOR ASS'Y T6-3-2000 (For TP-60D) T6-3-200 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-3-2000 Accumulator Ass'y (For 2mm) T6-3-200 Accumulator Ass'y (For 9mm) T6-3-0 Accumulator Bearing Case 2 T6-3-20 Accumulator Lower Shaft 3 T6-3-30 Accumulator Lower Roller 4 T6-3-40 Accumulator Main Roller & Shaft 5 T6-3-50 Accumulator Balance Bar Holder 6 T6-3-60 Accumulator Feed Shooter (For 2mm) T6-3-6 Accumulator Feed Shooter (For 9mm) 7 T6-3-270 Accumulator Lower Shaft Spring Hook 8 T6-3-80 Knob 9 T6-3-90 Bearing Collar 2 0 T6--760 Feed Roller Pulley BR6202ZZ Bearing, 6202ZZ 4 2 BR620ZZ Bearing, 620ZZ 2 3 BR6902ZZ Bearing, 6902ZZ 2 5 RR32 Snap Ring, H-32 2 7 ER2 Snap Ring, E-2 3 8 SR2 Stop Ring, S-2 5 HBS0635H HBS, M6 35 (H) 52 HSS065G HSS, M6 5 (G) 53 HSS060G HSS, M6 0 (G) 2 54 HSS0506G HSS, M5 6 (G) 55 HN06 HN, M6-5 -
3-2 ACCUMULATOR BOX GROUP T6-3-2000 (For TP-60D) T6-3-20002 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-3-2000 Accumulator Box Group (For 2mm) T6-3-2000S Accumulator Box Group (For 2mm) T6-3-20002 Accumulator Box Group (For 9mm) T6-3-20002S Accumulator Box Group (For 9mm) 3 T6-3-2030 Accumulator Box Front, LH T6-3-2030S Accumulator Box Front, LH 5 T6-3-2050 Spacer (For 9 mm) 2 T6-3-2060 Spacer (For 2 mm) 2 5 HBS0508 HBS, M5 8 2 HBS0508S HBS, M5 8 2 55 PW05 PW, M5 2 PW05S PW, M5 2 57 HBS0425H HBS, M4 25 (H) 2 HBS0425HS HBS, M4 25 (H) 2 58 SW04 SW, M4 2 SW04S SW, M4 2 59 PW04 PW, M4 2 PW04S PW, M4 2 60 SW05 SW, M5 2 SW05S SW, M5 2-53 -
3-3 ACCUMULATOR BOX GROUP T6-3-30004 (For TP-60L) T6-3-30005 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-3-30004 Accumulator Box Group (For TP-60L, 2mm) T6-3-30004S Accumulator Box Group (For TP-60L, 2mm) T6-3-30005 Accumulator Box Group (For TP-60L, 9mm) T6-3-30005S Accumulator Box Group (For TP-60L, 9mm) T6-3-3000 Inlet Guide (For 9mm) T6-3-300 Inlet Guide (For 2mm) 3 T6-3-30030 Strap Guide (For 9mm) T6-3-3003 Strap Guide (For 2mm) 5 T6-3-30200 Enclosed Plate (For 9mm) T6-3-3020 Enclosed Plate (For 2mm) 6 T6-3-3020 Enclosed Plate (For 9mm) T6-3-302 Enclosed Plate (For 2mm) 8 T6-3-30080 Inlet Strap Guide, Upper (For 9mm) T6-3-30080S Inlet Strap Guide, Upper (For 9mm) T6-3-3008 Inlet Strap Guide, Upper (For 2mm) T6-3-3008S Inlet Strap Guide, Upper (For 2mm) 9 T6-3-30090 Inlet Strap Guide, Lower (For 9mm) T6-3-30090S Inlet Strap Guide, Lower (For 9mm) T6-3-3009 Inlet Strap Guide, Lower (For 2mm) T6-3-3009S Inlet Strap Guide, Lower (For 2mm) 0 T6-3-3000 Strap Guide Cover T6-3-3000S Strap Guide Cover (Stainless Steel Model) 2 T6-3-3020 Strap Guide Bar (For 9mm) T6-3-302 Strap Guide Bar (For 2mm) - 55 -
3-3 ACCUMULATOR BOX GROUP T6-3-30004 (For TP-60L) T6-3-30005 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 3 T6-3-3030 Movable Strap Guide (For 9mm) T6-3-3030S Movable Strap Guide (For 9mm) T6-3-303 Movable Strap Guide (For 2mm) T6-3-303S Movable Strap Guide (For 2mm) 4 T6-3-3040 Lower Guide (For 9mm) T6-3-3040S Lower Guide (For 9mm)(Stainless Steel Model) T6-3-304 Lower Guide (For 2mm) T6-3-304S Lower Guide (For 2mm)(Stainless Steel Model) 5 T7-3-200 Assistant Roller Ass'y (For 9mm) T7-3-2002 Assistant Roller Ass'y (For 2mm) 6 T6-3-3062 Balance Bar (For 9mm) T6-3-3063 Balance Bar (For 2mm) 7 T6-3-3070 Control Lever (For 9mm) T6-3-307 Control Lever (For 2mm) 8 T6-3-3080 Pusher 20 T6-8-040 Motor Cover 2 2 T6--62 Motor (M5-) 2 22 T6--7240 Spring 23 T6-3-0200 Twist Stopper 2 24 T7--2020 Spring 25 T7--2030 Collar 26 T7-5-2020 Grommet 27 T7-3-032 Strap Guide (For 9mm) T7-3-033 Strap Guide (For 2mm) 28 T7-3-050 Shaft T7-3-050S Shaft 29 T7-3-070 Bracket 30 T7-3-080 Tube 3 T7-3-090 Support 32 T7-3-0200 Sensor Lever 33 T7-3-020 Bracket - 56 -
3-3 ACCUMULATOR BOX GROUP T6-3-30004 (For TP-60L) T6-3-30005 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 34 T7-3-200 Motor Support 35 T7-3-2050 Shaft 36 T7-3-2062 Assistant Roller (For 9mm) T7-3-2063 Assistant Roller (For 2mm) 37 T7-3-2070 Accumulator Main Roller T7-3-2070S Accumulator Main Roller (Stainless Steel Model) 38 T7-3-2080 Collar 39 T7-3-20200 Spacer 40 T7-3-202 Motor Ass'y (M3) 4 LA-50057 Label 2 42 T6-6-30200 Earth Plate (3P) 43 TB-223 Washer 44 T6-3-030 Accumulator Adjusting Pin 2 45 TF-006 Micro Switch (LS4) 46 TF-007 Micro Switch (LS5) 47 MV--720 Bolt 48 T6-3-30220 Twist 50 BR605ZZ Bearing, 605ZZ (For 9mm) 4 Bearing, 605ZZ (For 2mm) 6 5 BR608ZZ Bearing, 608ZZ 2 52 BR6900ZZ Bearing, 6900ZZ 2 53 KYA050520 Key, 5 5 20 54 MB00 Metal Bushing, 00 2 55 HBS046N HBS, M4 6 (N) 3 56 HBS0425N HBS, M4 25 (N) 2 57 HBS0508N HBS, M5 8 (N) 8 58 HBS052N HBS, M5 2 (N) 6 59 HBS0608N HBS, M6 8 (N) 3 60 HBS062N HBS, M6 2 (N) 6 HBS066N HBS, M6 6 (N) 62 HBS066N HBS, M6 6 (N)(For 9mm) 3 HBS0620N HBS, M6 20 (N)(For 2mm) 3 63 HBS056N HBS, M5 6 (N) 64 HBS0530N HBS, M5 30 (N) 2-57 -
3-3 ACCUMULATOR BOX GROUP T6-3-30004 (For TP-60L) T6-3-30005 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 65 HBS0630N HBS, M6 30 (N) 2 68 FMS030 FMS, M3 0 8 69 FMS040 FMS, M4 0 4 70 FMS050 FMS, M5 0 4 7 PMS036 PMS, M3 6 5 72 TMS0408 TMS, M4 8 4 75 HN03 HN, M3 76 HN05 HN, M5 2 77 HN08 HN, M8 3 78 HN04 HN, M4 2 79 HSS0405GN HSS, M4 5 (G)(N) 5 HSS0405S HSS, M4 5 5 80 HSS0508GN HSS, M5 8 (G)(N) 4 8 HSS060GN HSS, M6 0 (G)(N) 2 82 HBS042N HBS, M4 2 (N) 3 84 PW04 PW, M4 5 85 PW05 PW, M5 0 86 PW06A PW, M6 (A) 8 87 SW03 SW, M3 5 88 SW04 SW, M4 8 89 SW05 SW, M5 7 90 SW06 SW, M6 8 9 SW08 SW, M8 92 PW08A PW, M8 (A) - 58 -
4-2 REEL CONTROL GROUP T6-4-20000 (For TP-60D) T6-4-20007 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-4-20000 Reel Control Group (For 200mm)(For TP-60D) T6-4-20000S Reel Control Group (For 200mm)(For TP-60D) T6-4-20007 Reel Control Group (For 280mm) (For TP-60D)(Option) T6-4-20007S Reel Control Group (For 280mm)(For TP-60D) (Option) T6-4-200 Reel Unit Base 3 T6-4-2030 Brake Tension Holder 4 T6-4-2040 Brake Belt Tightener T6-4-2040S Brake Belt Tightener (Stainless Steel Model) 5 T6-4-2050 Reel Shaft T6-4-2050S Reel Shaft 6 T6-4-2060 Holder Shaft 2 T6-4-2060S Holder Shaft 2 7 T6-4-2070 Reel Brake Arm T6-4-2070S Reel Brake Arm 8 T6-4-2080 Brake Tension Arm Spring T6-4-2080S Brake Tension Arm Spring (Stainless Steel Model) 9 T6-4-2090 Brake Tension Spring Ring 0 BR6205ZZ Bearing, 6205ZZ 2 MB525 Metal Bushing, 525 2 2 T6-4-2030 Collar 3 ER9 Snap Ring, E-9 ER9S Snap Ring, E-9 4 ER2 Snap Ring, E-2 5 ER2S Snap Ring, E-2 5 5 SR08 Stop Ring, S-8 SR08S Stop Ring, S-8 6 T6-4-20260 Spring Hook 7 T6-4-20270 Set Block T6-4-20270S Set Block - 63 -
REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 8 T6-4-20280 Washer T6-4-20280S Washer 9 T6-4-20290 Collar 20 T6-4-20300 Collar 2 TC-03 Inner Flange 23 TC-04 Outer Flange 24 TC-05 Protector 25 TC-06 Reel Nut Handle 27 TC-020 Pin 28 TC-02 Split Pin 30 TC-075 Center Drum (For 280mm)(Option) 4 T6-4-2000 Brake Belt Ass'y SEE PAGE 65 T6-4-2000S Brake Belt Ass'y (Stainless Steel SEE PAGE 65 Model) 42 T6-4-22000 Free Slide Roller Ass'y SEE PAGE 66 T6-4-22000S Free Slide Roller Ass'y (Stainless Steel Model) SEE PAGE 66 5 HBS0625 HBS, M6 25 HBS0625S HBS, M6 25 52 HBS0620 HBS, M6 20 3 HBS0620S HBS, M6 20 3 53 HBS066 HBS, M6 6 2 HBS066S HBS, M6 6 2 54 HN06 HN, M6 3 HN06S HN, M6 3 55 SW06 SW, M6 3 SW06S SW, M6 3 56 HSS0606G HSS, M6 6 (G) HSS0606S HSS, M6 6 57 HB086 HB, M8 6 HB086S HB, M8 6 58 LA-300 Label 60 PW06A PW, M6 (A) 3 PW06AS PW, M6 (A) 3
4-3 REEL CONTROL GROUP T6-4-30000 (For TP-60L) T6-4-3000 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 0 TL-02 Reel Support TL-02S Reel Support TL-02 Brake Arm TL-02S Brake Arm 2 TL-030 Brake Lining 3 TC-075 Center Drum (For 280mm)(Option) 2 ER04 Snap Ring, E-4 2 ER04S Snap Ring, E-4 2 22 HBS0820 HBS, M8 20 4 HBS0820S HBS, M8 20 4 23 SR0 Stop Ring, S-0 2 SR0S Stop Ring, S-0 2 24 SW08 SW, M8 4 SW08S SW, M8 4 25 PW08A PW, M8 (A) 4 PW08AS PW, M8 (A) 4-68 -
5 BODY FRAME GROUP T6-5-00 T6-5-003 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-5-0026 T6-5-0026S Body Frame Group (For TP-60D, 850W) Body Frame Group (For TP-60D, 850W) SEE PAGE 72 SEE PAGE 72 3 T6-5-003 Body Frame Group (For TP-60L, 850W) T6-5-003S Body Frame Group (For TP-60L, 850W) T6-5-0032 Body Frame Group (For TP-60L, 050W) T6-5-0032S Body Frame Group (For TP-60L, 050W) T6-5-0033 Body Frame Group (For TP-60L, 250W) T6-5-0033S Body Frame Group (For TP-60L, 250W) T6-5-0034 Body Frame Group (For TP-60L, 450W) T6-5-0034S Body Frame Group (For TP-60L, 450W) T6-5-0035 Body Frame Group (For TP-60L, 650W) T6-5-0035S Body Frame Group (For TP-60L, 650W) T6-5-0036 Body Frame Group (For TP-60L, 850W) T6-5-0036S Body Frame Group (For TP-60L, 850W) T6-5-0039 Body Frame Group (For TP-60L, 650W) T6-5-0039S Body Frame Group (For TP-60L, 650W) SEE PAGE 79 SEE PAGE 79 SEE PAGE 79 SEE PAGE 79 SEE PAGE 79 SEE PAGE 79 SEE PAGE 79 SEE PAGE 79 SEE PAGE 79 SEE PAGE 79 SEE PAGE 79 SEE PAGE 79 SEE PAGE 79 SEE PAGE 79-7 -
5- BODY FRAME GROUP T6-5-00 (For TP-60D) T6-5-002 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-5-00 T6-5-00S T6-5-002 T6-5-002S T6-5-0022 T6-5-0022S T6-5-0023 T6-5-0023S T6-5-0024 T6-5-0024S T6-5-0025 T6-5-0025S T6-5-0026 T6-5-0026S Body Frame Group (For TP-60D, 850W) Body Frame Group (For TP-60D, 850W) Body Frame Group (For TP-60D, 650W) Body Frame Group (For TP-60D, 650W) Body Frame Group (For TP-60D, 050W) Body Frame Group (For TP-60D, 050W) Body Frame Group (For TP-60D, 250W) Body Frame Group (For TP-60D, 250W) Body Frame Group (For TP-60D, 450W) Body Frame Group (For TP-60D, 450W) Body Frame Group (For TP-60D, 650W) Body Frame Group (For TP-60D, 650W) Body Frame Group (For TP-60D, 850W) Body Frame Group (For TP-60D, 850W) 2 T6-5-080 Front Door T6-5-080S Front Door 3 T6-5-030 Front Door Handle T6-5-030S Front Door Handle (Stainless Steel Model) - 73 -
5- BODY FRAME GROUP T6-5-00 (For TP-60D) T6-5-002 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 6 T6-5-060 Magnet Catch 2 7 T6-5-40009 Enclosed Bottom Plate T6-5-40009S Enclosed Bottom Plate (Stainless Steel Model) 8 T6-5-40020 Power Switch Bracket 9 T6-5-090 Rear Plate T6-5-090S Rear Plate 2 T6-5-0220 Rear Cover T6-5-0220S Rear Cover 3 T6-5-0230 Caster (Free)(For 650W~650W) 4 Caster (Free)(For 850W) 6 T6-5-0232 Caster (Free)(For 650W~650W) 2 Caster (Free)(For 850W)(Stainless 4 Steel Model) T6-5-023 Caster (Free)(Option) 2 5 T6-5-0250 Nylon Washer 2 6 T6-5-0260 Cover 7 T6-5-0270 Caster (Brake)(Option) 2 T6-5-027 Caster (Brake) 2 4 T6-5-3005 Body Frame (For 850W) T6-5-3005S Body Frame (For 850W)(Stainless Steel Model) T6-5-3006 Body Frame (For 650W) T6-5-3006S Body Frame (For 650W)(Stainless Steel Model) T6-5-3007 Body Frame (For 250W) T6-5-3007S Body Frame (For 250W)(Stainless Steel Model) T6-5-3008 Body Frame (For 850W) T6-5-3008S Body Frame (For 850W)(Stainless Steel Model) - 74 -
5- BODY FRAME GROUP T6-5-00 (For TP-60D) T6-5-002 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-5-300 Body Frame (For 450W) T6-5-300S Body Frame (For 450W)(Stainless Steel Model) T6-5-30 Body Frame (For 650W) T6-5-30S Body Frame (For 650W)(Stainless Steel Model) T6-5-305 Body Frame (For 050W) T6-5-305S Body Frame (For 050W)(Stainless Steel Model) 42 T6-5-000 Upper Table, Front Ass'y (For 850W) SEE PAGE 86 T6-5-000S Upper Table, Front Ass'y (For 850W) SEE PAGE 86 T6-5-009 Upper Table, Front Ass'y (For 650W) SEE PAGE 86 T6-5-009S Upper Table, Front Ass'y (For 650W) SEE PAGE 86 43 T6-5-200 Upper Table, Rear Ass'y (For 850W) SEE PAGE 88 T6-5-200S Upper Table, Rear Ass'y (For 850W) SEE PAGE 88 T6-5-2024 Upper Table, Rear Ass'y (For 650W) SEE PAGE 88 T6-5-2024S Upper Table, Rear Ass'y (For 650W) SEE PAGE 88 44 T6-5-002 Upper Table, Front Ass'y (For 050W) T6-5-002S Upper Table, Front Ass'y (For 050W) T6-5-003 Upper Table, Front Ass'y (For 250W) T6-5-003S Upper Table, Front Ass'y (For 250W) T6-5-004 Upper Table, Front Ass'y (For 450W) T6-5-004S Upper Table, Front Ass'y (For 450W) T6-5-005 Upper Table, Front Ass'y (For 650W) T6-5-005S Upper Table, Front Ass'y (For 650W) T6-5-006 Upper Table, Front Ass'y (For 850W) T6-5-006S Upper Table, Front Ass'y (For 850W) - 75 -
5- BODY FRAME GROUP T6-5-00 (For TP-60D) T6-5-002 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 45 T6-5-2002 Upper Table, Rear Ass'y (For 050W) T6-5-2002S Upper Table, Rear Ass'y (For 050W) T6-5-2003 Upper Table, Rear Ass'y (For 250W) T6-5-2003S Upper Table, Rear Ass'y (For 250W) T6-5-2004 Upper Table, Rear Ass'y (For 450W) T6-5-2004S Upper Table, Rear Ass'y (For 450W) T6-5-206 Upper Table, Rear Ass'y (For 650W) T6-5-206S Upper Table, Rear Ass'y (For 650W) T6-5-207 Upper Table, Rear Ass'y (For 850W) T6-5-207S Upper Table, Rear Ass'y (For 850W) 46 T6-5-0540 Upper Right Table, Front Set (For 050~850W) T6-5-0540S Upper Right Table, Front Set (For 050~850W) 47 T6-5-058 Upper Right Table, Rear Set (For 050~850W) T6-5-058S Upper Right Table, Rear Set (For 050~850W) 48 T6-5-0550 Upper Left Table, Front Set (For 050W) T6-5-0550S Upper Left Table, Front Set (For 050W) T6-5-0560 Upper Left Table, Front Set (For 250W) T6-5-0560S Upper Left Table, Front Set (For 250W) T6-5-0570 Upper Left Table, Front Set (For 450W) T6-5-0570S Upper Left Table, Front Set (For 450W) SEE PAGE 90 SEE PAGE 90 SEE PAGE 9 SEE PAGE 9 SEE PAGE 92 SEE PAGE 92 SEE PAGE 92 SEE PAGE 92 SEE PAGE 92 SEE PAGE 92-76 -
5- BODY FRAME GROUP T6-5-00 (For TP-60D) T6-5-002 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-5-057 T6-5-057S T6-5-0572 T6-5-0572S Upper Left Table, Front Set (For 650W) Upper Left Table, Front Set (For 650W) Upper Left Table, Front Set (For 850W) Upper Left Table, Front Set (For 850W) SEE PAGE 92 SEE PAGE 92 SEE PAGE 92 SEE PAGE 92 49 T6-5-0590 Upper Left Table, Rear Set (For 050W) T6-5-0590S Upper Left Table, Rear Set (For 050W) T6-5-0600 Upper Left Table, Rear Set (For 250W) T6-5-0600S Upper Left Table, Rear Set (For 250W) T6-5-0850 Upper Left Table, Rear Set (For 450W) T6-5-0850S Upper Left Table, Rear Set (For 450W) T6-5-085 Upper Left Table, Rear Set (For 650W) T6-5-085S Upper Left Table, Rear Set (For 650W) T6-5-0852 Upper Left Table, Rear Set (For 850W) T6-5-0852S Upper Left Table, Rear Set (For 850W) SEE PAGE 95 SEE PAGE 95 SEE PAGE 95 SEE PAGE 95 SEE PAGE 95 SEE PAGE 95 SEE PAGE 95 SEE PAGE 95 SEE PAGE 95 SEE PAGE 95 50 T6-5-0200 Grommet 52 TMS065S TMS, M6 5 (SUS) 4 53 FMS065S FMS, M6 5 (SUS)(For 050~850W) 4 54 TMS0308 TMS, M3 8 2-77 -
5- BODY FRAME GROUP T6-5-00 (For TP-60D) T6-5-002 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 56 TMS0508 TMS, M5 8 5 TMS0508S TMS, M5 8 5 57 HB066 HB, M6 6 6 HB066S HB, M6 6 6 58 PW05 PW, M5 3 PW05S PW, M5 3 59 SW06 SW, M6 8 60 SW06S SW, M6 6 6 TMS0408 TMS, M4 8 0 TMS0408S TMS, M4 8 0 62 PW06A PW, M6 (A) 2 63 PW06C PW, M6 (C) 6 PW06CS PW, M6 (C) 6 7 HBS062 HBS, M6 2 2 8 T6-5-090 Bracket T6-5-090S Bracket 82 TMS052 TMS, M5 2 TMS052S TMS, M5 2 83 SW05 SW, M5 SW05S SW, M5-78 -
5-2 BODY FRAME GROUP T6-5-003 (For TP-60L) T6-5-0032 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-5-003 Body Frame Group (For TP-60L, 850W) T6-5-003S Body Frame Group (For TP-60L, 850W) T6-5-0032 Body Frame Group (For TP-60L, 050W) T6-5-0032S Body Frame Group (For TP-60L, 050W) T6-5-0033 Body Frame Group (For TP-60L, 250W) T6-5-0033S Body Frame Group (For TP-60L, 250W) T6-5-0034 Body Frame Group (For TP-60L, 450W) T6-5-0034S Body Frame Group (For TP-60L, 450W) T6-5-0035 Body Frame Group (For TP-60L, 650W) T6-5-0035S Body Frame Group (For TP-60L, 650W) T6-5-0036 Body Frame Group (For TP-60L, 850W) T6-5-0036S Body Frame Group (For TP-60L, 850W) T6-5-0039 Body Frame Group (For TP-60L, 650W) T6-5-0039S Body Frame Group (For TP-60L, 650W) T6-5-50 Accumulator Box T6-5-50S Accumulator Box (Stainless Steel Model) 2 T6-5-5020 Accumulator Box Cover T6-5-5020S Accumulator Box Cover (Stainless Steel Model) - 80 -
5-2 BODY FRAME GROUP T6-5-003 (For TP-60L) T6-5-0032 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 3 T6-5-5030 Cover 2 T6-5-5030S Cover 2 4 T6-5-5040 Bracket 2 5 T6-5-5050 Cover T6-5-5050S Cover 6 T6-5-5000 Body Frame (For 850W) T6-5-5000S Body Frame (For 850W)(Stainless Steel Model) T6-5-500 Body Frame (For 050W) T6-5-500S Body Frame (For 050W)(Stainless Steel Model) T6-5-5002 Body Frame (For 250W) T6-5-5002S Body Frame (For 250W)(Stainless Steel Model) T6-5-5003 Body Frame (For 450W) T6-5-5003S Body Frame (For 450W)(Stainless Steel Model) T6-5-5004 Body Frame (For 650W) T6-5-5004S Body Frame (For 650W)(Stainless Steel Model) T6-5-5005 Body Frame (For 850W) T6-5-5005S Body Frame (For 850W)(Stainless Steel Model) T6-5-5008 Body Frame (For 650W) T6-5-5008S Body Frame (For 650W)(Stainless Steel Model) 7 T6-5-0230 Caster (Free) 7 T6-5-0232 Caster (Free) 7 8 T6-5-000 Upper Table, Front Ass'y (For 850W) SEE PAGE 86 T6-5-000S Upper Table, Front Ass'y (For 850W) SEE PAGE 86 T6-5-009 Upper Table, Front Ass'y (For 650W) SEE PAGE 86 T6-5-009S Upper Table, Front Ass'y (For 650W) SEE PAGE 86-8 -
5-2 BODY FRAME GROUP T6-5-003 (For TP-60L) T6-5-0032 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 9 T6-5-200 Upper Table, Rear Ass'y (For 850W) SEE PAGE 88 T6-5-200S Upper Table, Rear Ass'y (For 850W) SEE PAGE 88 T6-5-2024 Upper Table, Rear Ass'y (For 650W) SEE PAGE 88 T6-5-2024S Upper Table, Rear Ass'y (For 650W) SEE PAGE 88 0 T6-5-002 Upper Table, Front Ass'y (For 050W) T6-5-002S Upper Table, Front Ass'y (For 050W) T6-5-003 Upper Table, Front Ass'y (For 250W) T6-5-003S Upper Table, Front Ass'y (For 250W) T6-5-004 Upper Table, Front Ass'y (For 450W) T6-5-004S Upper Table, Front Ass'y (For 450W) T6-5-005 Upper Table, Front Ass'y (For 650W) T6-5-005S Upper Table, Front Ass'y (For 650W) T6-5-006 Upper Table, Front Ass'y (For 850W) T6-5-006S Upper Table, Front Ass'y (For 850W) T6-5-2002 Upper Table, Rear Ass'y (For 050W) T6-5-2002S Upper Table, Rear Ass'y (For 050W) T6-5-2003 Upper Table, Rear Ass'y (For 250W) T6-5-2003S Upper Table, Rear Ass'y (For 250W) T6-5-2004 Upper Table, Rear Ass'y (For 450W) T6-5-2004S Upper Table, Rear Ass'y (For 450W) T6-5-206 Upper Table, Rear Ass'y (For 650W) T6-5-206S Upper Table, Rear Ass'y (For 650W) - 82 -
5-2 BODY FRAME GROUP T6-5-003 (For TP-60L) T6-5-0032 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-5-207 Upper Table, Rear Ass'y (For 850W) T6-5-207S Upper Table, Rear Ass'y (For 850W) 2 T6-5-0540 Upper Right Table, Front Set SEE PAGE 90 (For 050~850W) T6-5-0540S Upper Right Table, Front Set (For SEE PAGE 90 050~850W) 3 T6-5-0550 Upper Left Table, Front Set SEE PAGE 92 (For 050W) T6-5-0550S Upper Left Table, Front Set SEE PAGE 92 (For 050W) T6-5-0560 Upper Left Table, Front Set SEE PAGE 92 (For 250W) T6-5-0560S Upper Left Table, Front Set SEE PAGE 92 (For 250W) T6-5-0570 Upper Left Table, Front Set SEE PAGE 92 (For 450W) T6-5-0570S Upper Left Table, Front Set SEE PAGE 92 (For 450W) T6-5-057 Upper Left Table, Front Set SEE PAGE 92 (For 650W) T6-5-057S Upper Left Table, Front Set SEE PAGE 92 (For 650W) T6-5-0572 Upper Left Table, Front Set SEE PAGE 92 (For 850W) T6-5-0572S Upper Left Table, Front Set SEE PAGE 92 (For 850W) 4 T6-5-058 Upper Right Table, Rear Set SEE PAGE 9 (For 050~850W) T6-5-058S Upper Right Table, Rear Set (For SEE PAGE 9 050~850W) 5 T6-5-0590 Upper Left Table, Rear Set SEE PAGE 95 (For 050W) T6-5-0590S Upper Left Table, Rear Set (For 050W) SEE PAGE 95-83 -
5-2 BODY FRAME GROUP T6-5-003 (For TP-60L) T6-5-0032 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-5-0600 T6-5-0600S T6-5-0850 T6-5-0850S T6-5-085 T6-5-085S T6-5-0852 T6-5-0852S Upper Left Table, Rear Set (For 250W) Upper Left Table, Rear Set (For 250W) Upper Left Table, Rear Set (For 450W) Upper Left Table, Rear Set (For 450W) Upper Left Table, Rear Set (For 650W) Upper Left Table, Rear Set (For 650W) Upper Left Table, Rear Set (For 850W) Upper Left Table, Rear Set (For 850W) SEE PAGE 95 SEE PAGE 95 SEE PAGE 95 SEE PAGE 95 SEE PAGE 95 SEE PAGE 95 SEE PAGE 95 SEE PAGE 95 2 HBS056 HBS, M5 6 4 HBS056S HBS, M5 6 4 22 HBS0820 HBS, M8 20 4 HBS0820S HBS, M8 20 4 23 HB066 HB, M6 6 28 HB066S HB, M6 6 28 26 TMS0508 TMS, M5 8 24 TMS0508S TMS, M5 8 24 27 TMS065S TMS, M6 5 (SUS) 4 28 FMS065S FMS, M6 5 (SUS)(For 050~850W) 4 3 PW04 PW, M4 4 PW04S PW, M4 4 32 PW06C PW, M6 (C) 28 PW06CS PW, M6 (C) 28 33 PW08C PW, M8 (C) 4 PW08CS PW, M8 (C) 4-84 -
5-2 BODY FRAME GROUP T6-5-003 (For TP-60L) T6-5-0032 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 36 SW04 SW, M4 4 SW04S SW, M4 4 37 SW06 SW, M6 28 SW06S SW, M6 28 38 SW08 SW, M8 4 SW08S SW, M8 4-85 -
5-2- UPPER TABLE, FRONT ASS'Y T6-5-000 T6-5-009 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 4 ER07 Snap Ring, E-7 8 ER07S Snap Ring, E-7 8 5 T6-5-50 Table Handle 2 T6-5-50S Table Handle 2 6 TMS062 TMS, M6 2 4 TMS062S TMS, M6 2 4 8 SW06 SW, M6 4 SW06S SW, M6 4-87 -
5-2-2 UPPER TABLE, REAR ASS'Y T6-5-200 T6-5-2024 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 4 ER07 Snap Ring, E-7 8 ER07S Snap Ring, E-7 8 5 T6-5-50 Table Handle 2 T6-5-50S Table Handle 2 6 TMS062 TMS, M6 2 4 TMS062S TMS, M6 2 4 8 SW06 SW, M6 4 SW06S SW, M6 4-89 -
5-2-5 UPPER LEFT TABLE, FRONT SET T6-5-0550 T6-5-0560 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-5-030 Upper Left Table Front (For 050W) T6-5-030S Upper Left Table Front (For 050W) T6-5-040 Upper Left Table Front (For 250W) T6-5-040S Upper Left Table Front (For 250W) T6-5-050 Upper Left Table Front (For 450W) T6-5-050S Upper Left Table Front (For 450W) T6-5-060 Upper Left Table Front (For 650W) T6-5-060S Upper Left Table Front (For 650W) T6-5-070 Upper Left Table Front (For 850W) T6-5-070S Upper Left Table Front (For 850W) 2 T6-5-20 Table Roller (For 250W/450W) 2 Table Roller (For 650W/850W) 4 T6-5-2 Table Roller (For 250W/450W) 2 Table Roller (For 650W/850W) 4 3 T6-5-30 Table Roller Shaft (For 250W/450W) 2 Table Roller Shaft (For 650W/850W) 4 T6-5-3 Table Roller Shaft (For 2 250W/450W) Table Roller Shaft (For 4 650W/850W) 4 ER07 Snap Ring, E-7 (For 250W/450W) 4 Snap Ring, E-7 (For 650W/850W) 8 ER07S Snap Ring, E-7 (For 250W/450W) 4 Snap Ring, E-7 (For 650W/850W) 8-93 -
5-2-5 UPPER LEFT TABLE, FRONT SET T6-5-0550 T6-5-0560 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 5 T6-5-50 Table Handle T6-5-50S Table Handle 6 TMS062 TMS, M6 2 2 TMS062S TMS, M6 2 2 8 SW06 SW, M6 2 SW06S SW, M6 2-94 -
5-2-6 UPPER LEFT TABLE, REAR SET T6-5-0590 T6-5-0600 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-5-2030 Upper Left Table Rear (For 050W) T6-5-2030S Upper Left Table Rear (For 050W) T6-5-2040 Upper Left Table Rear (For 250W) T6-5-2040S Upper Left Table Rear (For 250W) T6-5-2050 Upper Left Table Rear (For 450W) T6-5-2050S Upper Left Table Rear (For 450W) T6-5-2060 Upper Left Table Rear (For 650W) T6-5-2060S Upper Left Table Rear (For 650W) T6-5-2070 Upper Left Table Rear (For 850W) T6-5-2070S Upper Left Table Rear (For 850W) 2 T6-5-20 Table Roller (For 250W/450W) 2 Table Roller (For 650W/850W) 4 T6-5-2 Table Roller (For 250W/450W) 2 Table Roller (For 650W/850W) 4 3 T6-5-30 Table Roller Shaft (For 250W/450W) 2 Table Roller Shaft (For 650W/850W) 4 T6-5-3 Table Roller Shaft (For 250W/450W) 2 Table Roller Shaft (For 650W/850W) 4 4 ER07 Snap Ring, E-7 (For 250W/450W) 4 Snap Ring, E-7 (For 650W/850W) 8 ER07S Snap Ring, E-7 (For 250W/450W) 4 Snap Ring, E-7 (For 650W/850W) 8 5 T6-5-50 Table Handle T6-5-50S Table Handle - 96 -
5-2-6 UPPER LEFT TABLE, REAR SET T6-5-0590 T6-5-0600 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 6 TMS062 TMS, M6 2 2 TMS062S TMS, M6 2 2 8 SW06 SW, M6 2 SW06S SW, M6 2-97 -
6 ELECTRIC CONTROL GROUP T6-6-0004 T6-6-000 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-6-0004 Electric Control Group (For TP-60D, PH, 220V) SEE PAGE 00 T6-6-0004S Electric Control Group (For TP-60D, PH, 220V) SEE PAGE 00 T6-6-0006 Electric Control Group (For TP-60D, PH, 0V) SEE PAGE 00 T6-6-0006S Electric Control Group (For TP-60D, PH, 0V) SEE PAGE 00 T6-6-0007 Electric Control Group (For TP-60D, PH, 240V) SEE PAGE 00 T6-6-0007S Electric Control Group (For TP-60D, PH, 240V) SEE PAGE 00 T6-6-007 Electric Control Group (For TP-60D3, 3PH) SEE PAGE 00 T6-6-007S Electric Control Group (For TP-60D3, 3PH) SEE PAGE 00 2 T6-6-000 Electric Control Group (For TP-60L, PH, 220V) T6-6-000S Electric Control Group (For TP-60L, PH, 220V) T6-6-002 Electric Control Group (For TP-60L, PH, 0V) T6-6-002S Electric Control Group (For TP-60L, PH, 0V) T6-6-003 Electric Control Group (For TP-60L, PH, 240V) T6-6-003S Electric Control Group (For TP-60L, PH, 240V) T6-6-008 Electric Control Group (For TP-60L3, 3PH) T6-6-008S Electric Control Group (For TP-60L3, 3PH) SEE PAGE 05 SEE PAGE 05 SEE PAGE 05 SEE PAGE 05 SEE PAGE 05 SEE PAGE 05 SEE PAGE 05 SEE PAGE 05-99 -
6- ELECTRIC CONTROL GROUP T6-6-0004 (For TP-60D / TP-60D3) T6-6-0006 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-6-0004 Electric Control Group (For TP-60D, PH, 220V) T6-6-0004S Electric Control Group (For TP-60D, PH, 220V) T6-6-0006 Electric Control Group (For TP-60D, PH, 0V) T6-6-0006S Electric Control Group (For TP-60D, PH, 0V) T6-6-0007 Electric Control Group (For TP-60D, PH, 240V) T6-6-0007S Electric Control Group (For TP-60D, PH, 240V) T6-6-007 Electric Control Group (For TP-60D3, 3PH) T6-6-007S Electric Control Group (For TP-60D3, 3PH) T6-6-30002 Motor (M) Pulley 2 TG-03 Fuse Holder 3 T6-6-3036 Motor (M2) Pulley 4 T6-6-040 Heater Terminal Bracket 5 TF-025 Knob 6 T6-6-06 Power Cord (Europe Plug)(For PH) T6-6-062 Power Cord (America Plug)(For PH) T6-6-063 Power Cord (For 3PH) 7 T6-6-40007 Fuse (5A) 0 T6-6-0200 Limit Switch Base T6-6-30200 Earth Plate (3P) 2 T5-4-030 Earth Plate (5P) 3 T5-4-023 Variable Resistor (5K)( 3) 4 T6--760 Feed Roller Pulley 5 T6-6-40002 Transformer Box Cover T6-6-40002S Transformer Box Cover (Stainless Steel Model) - 0 -
REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 6 T6-6-0260 Smoke Fan Bracket 2 T6-6-40006 Transformer Box T6-6-40006S Transformer Box (Stainless Steel Model) 22 T6-6-0320 Heater Terminal 24 T6-6-0340 Cable Gland (PG3.5) 25 T6-6-0350 Connector (Foot Switch) 28 T6-6-0380 Limit Switch (LS4) 30 TF-027 Selector Switch 3 TF-02 Fan (Only 0V) TF-02- Fan 33 T6-6-3005 Motor (M)(For PH, 0V) T6-6-30052 Motor (M)(For PH, 240V) T6-6-30060 Motor (M)(For PH, 220V) T6-6-0442 Motor (M)(For 3PH) 35 T6-6-30054 Motor (M2)(For PH, 0V) T6-6-30055 Motor (M2)(For PH, 240V) T6-6-30070 Motor (M2)(For PH, 220V) T6-6-0442 Motor (M2)(For 3PH) 38 T6-6-40040 Main Power Switch 39 T6-6-30057 Motor (M3)(For PH, 0V) T6-6-30058 Motor (M3)(For PH, 240V) T6-6-30080 Motor (M3)(For PH, 220V) T6-6-0442 Motor (M3)(For 3PH) 42 TF-024 Transformer Cover
6- ELECTRIC CONTROL GROUP T6-6-0004 (For TP-60D / TP-60D3) T6-6-0006 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 44 T6-6-0540 Bracket (Only PH M2 Fan) 45 T6-6-0550 Fan (For M/M2 Motor, PH, 0V) 2 T6-6-055 Fan (For M/M2 Motor, PH, 2 220V/230V/240V) 46 T6-6-0560 Bracket (Only PH M Fan) 48 LA-2040 Label 53 HBS050 HBS, M5 0 4 54 HBS052 HBS, M5 2 55 PMS040 PMS, M4 0 2 56 HSS060G HSS, M6 0 (G) 4 58 HBS0620 HBS, M6 20 2 59 TMS0308 TMS, M3 8 4 60 TMS0408S TMS, M4 8 8 6 TMS0408 TMS, M4 8 7 62 TMS0508 TMS, M5 8 6 64 PMS0408 PMS, M4 8 2 65 PMS035 PMS, M3 5 2 66 HN06 HN, M6 2 68 HN03 HN, M3 2 69 PW06D PW, M6 (D)(Only PH) 2 70 PW06C PW, M6 (C)(For PH) 22 PW06C PW, M6 (C)(For 3PH) 24 72 PW05 PW, M5 4 74 SW05 SW, M5 3 75 SW06 SW, M6 2 76 SW04 SW, M4 4 77 T6-6-07 Heater Transformer Ass'y T6-6-072 Heater Transformer Ass'y (Only 0V) 78 SW03 SW, M3 2-03 -
6- ELECTRIC CONTROL GROUP T6-6-0004 (For TP-60D / TP-60D3) T6-6-0006 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 79 T6-6-0893 Motor starting capacitor (For M/M2, 2 PH, 0V) T6-6-0894 Motor starting capacitor (For M/M2, 2 PH, 240V) T6-6-0895 Motor starting capacitor (For M/M2, PH, 220V) 2 8 T6-6-092 Motor starting capacitor (For M3, PH, 0V) T6-6-094 Motor starting capacitor (For M3, PH, 240V) T6-6-095 Motor starting capacitor (For M3, PH, 220V) 88 T6-6-0980 Cable Gland (PG) 3 89 LA-20080 Label 90 T5-4-022 Knob 9 T7-5-2030 Micro Switch 93 T7-6-4000 Pedal Control Set - 04 -
6-2 ELECTRIC CONTROL GROUP T6-6-000 (For TP-60L / TP-60L3) T6-6-002 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-6-000 Electric Control Group (For TP-60L, PH, 220V) T6-6-000S Electric Control Group (For TP-60L, PH, 220V) T6-6-002 Electric Control Group (For TP-60L, PH, 0V) T6-6-002S Electric Control Group (For TP-60L, PH, 0V) T6-6-003 Electric Control Group (For TP-60L, PH, 240V) T6-6-003S Electric Control Group (For TP-60L, PH, 240V) T6-6-008 Electric Control Group (For TP-60L3, 3PH) T6-6-008S Electric Control Group (For TP-60L3, 3PH) T6-6-30002 Motor (M) Pulley 2 TG-03 Fuse Holder 3 T6-6-3036 Motor (M2) Pulley 4 T6-6-040 Heater Terminal Bracket 5 TF-025 Knob 6 T6-6-06 Power Cord (Europe Plug)(For PH) T6-6-062 Power Cord (America Plug)(For PH) T6-6-063 Power Cord (For 3PH) 7 T6-6-40007 Fuse (5A) T6-6-30200 Earth Plate (3P) 5 T6-6-40002 Transformer Box Cover T6-6-40002S Transformer Box Cover (Stainless Steel Model) 6 T6-6-0260 Smoke Fan Bracket - 06 -
6-2 ELECTRIC CONTROL GROUP T6-6-000 (For TP-60L / TP-60L3) T6-6-002 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 2 T6-6-40006 Transformer Box T6-6-40006S Transformer Box (Stainless Steel Model) 22 T6-6-0320 Heater Terminal 24 T6-6-0340 Cable Gland (PG3.5) 25 T6-6-0350 Connector (Foot Switch) 30 TF-027 Selector Switch 3 TF-02 Fan (Only 0V) TF-02- Fan 33 T6-6-3005 Motor (M)(For PH, 0V) T6-6-30052 Motor (M)(For PH, 240V) T6-6-30060 Motor (M)(For PH, 220V) T6-6-0442 Motor (M)(For 3PH) 35 T6-6-30054 Motor (M2)(For PH, 0V) T6-6-30055 Motor (M2)(For PH, 240V) T6-6-30070 Motor (M2)(For PH, 220V) T6-6-0442 Motor (M2)(For 3PH) 38 T6-6-400 Main Power Switch 42 TF-024 Transformer Cover 44 T6-6-0540 Bracket (Only PH M2 Fan) 2 45 T6-6-0550 Fan (For M/M2 Motor, PH, 0V) 2 T6-6-055 Fan (For M/M2 Motor, PH, 2 220V/230V/240V) 48 LA-2040 Label 53 HBS050 HBS, M5 0 2 55 PMS040 PMS, M4 0 2 56 HSS060G HSS, M6 0 (G) 4-07 -
6-2 ELECTRIC CONTROL GROUP T6-6-000 (For TP-60L / TP-60L3) T6-6-002 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 58 HBS0620 HBS, M6 20 8 59 TMS0308 TMS, M3 8 4 60 TMS0408S TMS, M4 8 8 6 TMS0408 TMS, M4 8 7 62 TMS0508 TMS, M5 8 6 66 HN06 HN, M6 8 70 PW06C PW, M6 (C) 6 72 PW05 PW, M5 2 73 SW04 SW, M4 2 74 SW05 SW, M5 2 75 SW06 SW, M6 8 77 T6-6-07 Heater Transformer Ass'y T6-6-072 Heater Transformer Ass'y (Only 0V) 79 T6-6-0893 Motor starting capacitor (For M/M2, PH, 0V) T6-6-0894 Motor starting capacitor (For M/M2, PH, 240V) T6-6-0895 Motor starting capacitor (For M/M2, PH, 220V) 2 2 2 87 T5-4-023 Variable Resistor (5K)( 3) 88 T6-6-0980 Cable Gland (PG) 3 89 LA-20080 Label 90 T5-4-022 Knob 9 T7-5-2030 Micro Switch 93 T7-6-4000 Pedal Control Set - 08 -
7 AUTO STRAP FEEDING UNIT T6-8-9002 T6-8-9005 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-8-9002 T6-8-9002S T6-8-90024 T6-8-90024S T6-8-90025 T6-8-90025S T6-8-90026 T6-8-90026S T6-8-90027 T6-8-90027S T6-8-9003 T6-8-9003S T6-8-90034 T6-8-90034S Auto Strap Feeding Unit (For TP-60D, 9mm, 0V) Auto Strap Feeding Unit (For TP-60D, 9mm, 0V) Auto Strap Feeding Unit (For TP-60D, 9mm, 220V) Auto Strap Feeding Unit (For TP-60D, 9mm, 220V) Auto Strap Feeding Unit (For TP-60D, 9mm, 240V) Auto Strap Feeding Unit (For TP-60D, 9mm, 240V) Auto Strap Feeding Unit (For TP-60D3, 9mm, 220V) Auto Strap Feeding Unit (For TP- 60D3, 9mm, 220V)(Stainless Steel Model) Auto Strap Feeding Unit (For TP- 60D3, 9mm, 380V/400V/45V) Auto Strap Feeding Unit (For TP- 60D3, 9mm, 380V/400V/45V)(Stainless Steel Auto Strap Feeding Unit (For TP-60D, 2mm, 0V) Auto Strap Feeding Unit (For TP-60D, 2mm, 0V) Auto Strap Feeding Unit (For TP-60D, 2mm, 220V) Auto Strap Feeding Unit (For TP-60D, 2mm, 220V) - 0 -
7 AUTO STRAP FEEDING UNIT T6-8-9002 T6-8-9005 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-8-90035 T6-8-90035S T6-8-90036 T6-8-90036S T6-8-90037 T6-8-90037S T6-8-9005 T6-8-9005S T6-8-90052 T6-8-90052S T6-8-90057 T6-8-90057S T6-8-90059 T6-8-90059S Auto Strap Feeding Unit (For TP-60D, 2mm, 240V) Auto Strap Feeding Unit (For TP-60D, 2mm, 240V) Auto Strap Feeding Unit (For TP- 60D3, 2mm, 220V) Auto Strap Feeding Unit (For TP- 60D3, 2mm, 220V)(Stainless Steel Model) Auto Strap Feeding Unit (For TP- 60D3, 2mm, 380V/400V/45V) Auto Strap Feeding Unit (For TP- 60D3, 2mm, 380V/400V/45V) Auto Strap Feeding Unit (For TP-60L, 9mm, 0V) Auto Strap Feeding Unit (For TP-60L, 9mm, 0V) Auto Strap Feeding Unit (For TP-60L, 9mm, 220V) Auto Strap Feeding Unit (For TP-60L, 9mm, 220V) Auto Strap Feeding Unit (For TP-60L, 9mm, 240V) Auto Strap Feeding Unit (For TP-60L, 9mm, 240V) Auto Strap Feeding Unit (For TP-60L3, 9mm, 220V) Auto Strap Feeding Unit (For TP- 60L3, 9mm, 220V)(Stainless Steel Model) - -
7 AUTO STRAP FEEDING UNIT T6-8-9002 T6-8-9005 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-8-90060 Auto Strap Feeding Unit (For TP- 60L3, 9mm, 380V/400V/45V) T6-8-90060S Auto Strap Feeding Unit (For TP- 60L3, 9mm, 380V/400V/45V) T6-8-90054 Auto Strap Feeding Unit (For TP-60L, 2mm, 0V) T6-8-90054S Auto Strap Feeding Unit (For TP-60L, 2mm, 0V) T6-8-90055 Auto Strap Feeding Unit (For TP-60L, 2mm, 220V) T6-8-90055S Auto Strap Feeding Unit (For TP-60L, 2mm, 220V) T6-8-90058 Auto Strap Feeding Unit (For TP-60L, 2mm, 240V) T6-8-90058S Auto Strap Feeding Unit (For TP-60L, 2mm, 240V) T6-8-90079 Auto Strap Feeding Unit (For TP- 60L3, 2mm, 220V) T6-8-90079S Auto Strap Feeding Unit (For TP- 60L3, 2mm, 220V)(Stainless Steel Model) T6-8-90080 Auto Strap Feeding Unit (For TP- 60L3, 2mm, 380V/400V/45V) T6-8-90080S Auto Strap Feeding Unit (For TP- 60L3, 2mm, 380V/400V/45V) T6-8-0000 Auto Strap Feeding Group (For TP-60D, 9mm) SEE PAGE 4 T6-8-0000S Auto Strap Feeding Group (For TP- 60D, 9mm) SEE PAGE 4-2 -
7 AUTO STRAP FEEDING UNIT T6-8-9002 T6-8-9005 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-8-000 Auto Strap Feeding Group (For TP-60D, 2mm) SEE PAGE 4 T6-8-000S Auto Strap Feeding Group (For TP- 60D, 2mm) SEE PAGE 4 2 T6-8-0008 Auto Strap Feeding Group (For TP-60L, 9mm) SEE PAGE 7 T6-8-0008S Auto Strap Feeding Group (For TP- 60L, 9mm) SEE PAGE 7 T6-8-0009 Auto Strap Feeding Group (For TP-60L, 2mm) SEE PAGE 7 T6-8-0009S Auto Strap Feeding Group (For TP- 60L, 2mm) SEE PAGE 7 3 T6-8-20004 Electric Control Group (For TP-60D, 0V) SEE PAGE 20 T6-8-20025 Electric Control Group (For TP-60D, 220V) SEE PAGE 20 T6-8-20026 Electric Control Group (For TP-60D, 240V) SEE PAGE 20 T6-8-202 Electric Control Group (For TP-60D3, 220V) SEE PAGE 23 T6-8-2022 Electric Control Group (For TP-60D3, 380V/400V/45V) SEE PAGE 23 4 T6-8-20007 Electric Control Group (For TP-60L, 0V) SEE PAGE 26 T6-8-20029 Electric Control Group (For TP-60L, 220V) SEE PAGE 26 T6-8-20030 Electric Control Group (For TP-60L, 240V) SEE PAGE 26 T6-8-207 Electric Control Group (For TP-60L3, 220V) SEE PAGE 30 T6-8-208 Electric Control Group (For TP-60L3, 380V/400V/45V) SEE PAGE 30-3 -
7 AUTO STRAP FEEDING UNIT T6-8-9002 T6-8-9005 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 5 T6-8-3000 Control Group (For TP-60D) SEE PAGE 33 T6-8-3000S Control Group (For TP-60D) SEE PAGE 33 6 T6-8-30002 Control Group (For TP-60L) SEE PAGE 34-3- -
7- AUTO STRAP FEEDING GROUP T6-8-0000 (For TP-60D) T6-8-000 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-8-0000 Auto Strap Feeding Group (For TP-60D, 9mm) T6-8-0000S Auto Strap Feeding Group (For TP- 60D, 9mm) T6-8-000 Auto Strap Feeding Group (For TP-60D, 2mm) T6-8-000S Auto Strap Feeding Group (For TP- 60D, 2mm) T6-8-00 Feed Unit Guide 2 T6-8-020 Guide Cover 3 T6-8-030 Feed Shooter 4 T6-8-040 Strap Guide (For 2mm) T6-8-04 Strap Guide (For 9mm) 5 T6-8-050 Strap Guide (For 2mm) T6-8-05 Strap Guide (For 9mm) 6 T6-8-060 Control Lever (For 2mm) T6-8-06 Control Lever (For 9mm) 8 T6-8-080 Strap Guide (For 2mm) T6-8-08 Strap Guide (For 9mm) 9 T6-8-090 Accumulator Cover T6-8-090S Accumulator Cover (Stainless Steel Model) T6-8-020 Bracket T6-8-020S Bracket 2 T6--62 Motor (M5) 3 TF-007 Micro Switch 4 HBS056 HBS, M5 6 3 5 HBS050 HBS, M5 0 7 6 HBS0508 HBS, M5 8 7 7 HBS042 HBS, M4 2 2 HBS042S HBS, M4 2 2 8 TMS0508 TMS, M5 8 2 9 PMS0320 PMS, M3 20 2 20 HSS0506G HSS, M5 6 (G) 2 2 FMS030 FMS, M3 0 4-5 -
7- AUTO STRAP FEEDING GROUP T6-8-0000 (For TP-60D) T6-8-000 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 22 SW05 SW, M5 7 23 SW04 SW, M4 5 SW04S SW, M4 5 24 SW03 SW, M3 2 25 PW05 PW, M5 6 26 TMS0408 TMS, M4 8 2 27 PW03 PW, M3 2 28 HN03 HN, M3 2 30 LA-50057 Label 3 T6-8-040 Motor Cover 32 HBS0508S HBS, M5 8 5 33 SW05S SW, M5 5 34 PW05S PW, M5 5 35 HBS0408 HBS, M4 8 HBS0408S HBS, M4 8-6 -
7-2 AUTO STRAP FEEDING GROUP T6-8-0008 (For TP-60L) T6-8-0009 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-8-0008 T6-8-0008S T6-8-0009 T6-8-0009S Auto Strap Feeding Group (For TP- 60L, 9mm) Auto Strap Feeding Group (For TP- 60L, 9mm) Auto Strap Feeding Group (For TP- 60L, 2mm) Auto Strap Feeding Group (For TP- 60L, 2mm) T6-8-00 Feed Unit Guide 2 T6-8-020 Guide Cover T6-8-020S Guide Cover 3 T6-8-3003 Accumulator Cover T6-8-3003S Accumulator Cover (Stainless Steel Model) 4 T6-8-3033 Feed Shooter T6-8-3033S Feed Shooter 5 T6-3-2050 Spacer (For 9mm) 7 T6-3-2060 Spacer (For 2mm) 7 HBS050 HBS, M5 0 2 HBS050S HBS, M5 0 2 2 HBS056 HBS, M5 6 3 HBS056S HBS, M5 6 3 3 HBS0630 HBS, M6 30 8 HBS0630S HBS, M6 30 8 4 HBS0635 HBS, M6 35 2 HBS0635S HBS, M6 35 2 6 HN06 HN, M6 3 HN06S HN, M6 3 8 TMS0508 TMS, M5 8 2 TMS0508S TMS, M5 8 2-8 -
7-2 AUTO STRAP FEEDING GROUP T6-8-0008 (For TP-60L) T6-8-0009 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 2 SW05 SW, M5 5 SW05S SW, M5 5 22 SW06 SW, M6 22 SW06S SW, M6 22 25 PW05 PW, M5 4 PW05S PW, M5 4 26 PW06A PW, M6 (A) PW06AS PW, M6 (A) - 9 -
7-3- ELECTRIC CONTROL GROUP T6-8-20004 (For TP-60D) T6-8-20025 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-8-20004 Electric Control Group (For 0V) T6-8-20025 Electric Control Group (For 220V) T6-8-20026 Electric Control Group (For 240V) T6-8-20 Box 2 T6-8-220 Cover 3 LA-20086 Label 4 T6-6-3004 Transformer 5 T6-8-2050 P.C.Board (For 50HZ, Phase) T6-8-2060 P.C.Board (For 60HZ, Phase) 7 T6-6-30047 EMI Filter 8 T6-6-0353 Connector (Plug)(Power) 9 T6-6-3008 Connector (Heater) 0 T5-4-023 Variable Resistor (5K)( 3) T5-4-022 Knob 2 T5-4-060 Fuse Holder 6 3 T6-6-30033 Fuse (5A)(For 220V/230V/240V) 2 T6-6-3033 Fuse (0A)(For 0V) 2 4 T6-6-30034 Fuse (7A)(For 220V/230V/240V) T6-6-3033 Fuse (0A)(For 0V) 5 T6-6-3003 Fuse (2A) 6 T6-6-30036 Fuse (A) 7 T6-6-3003 Fuse (2A)(For 220V/230V/240V) T6-6-30032 Fuse (3A)(For 0V) 8 T6-8-20005 Electric Control Group (Without Wire Ass'y)(For 0V) T6-8-20027 Electric Control Group (Without Wire Ass'y)(For 220V) T6-8-20028 Electric Control Group (Without Wire Ass'y)(For 240V) 9 TMS0306 TMS, M3 6 8 20 TMS0508 TMS, M5 8 4 2 PMS0306 PMS, M3 6 4 22 PMS042 PMS, M4 2 2 23 SW04 SW, M4 3 24 HN04 HN, M4 3-2 -
7-3- ELECTRIC CONTROL GROUP T6-8-20004 (For TP-60D) T6-8-20025 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 25 T6-8-20440 Wire Ass'y X (Motor M) 26 T6-8-20450 Wire Ass'y X2 (Motor M2) 27 T6-8-20460 Wire Ass'y X3 (Motor M3) 28 T6-8-20470 Wire Ass'y X4 (Motor M5) 29 T6-8-20480 Wire Ass'y X5 (Motor M5-) 30 T6-8-5068 Proximity Sensor (X6, X9-)(LS6, 2 SEE PAGE 7 S.F.S.) 3 T7--20350 Photo Eye (X7)(PH) SEE PAGE 9 32 T6-8-2050 Wire Ass'y X8 (Control Panel) 34 T6-8-20520 Wire Ass'y X9 (LS4/LS5/Foot Switch) 35 T6-8-20530 Wire Ass'y X0 (T) 36 T6--068 Proximity Sensor (X, X2)(LS2, LS3) 2 SEE PAGE 4 38 T6-8-20560 Wire Ass'y X3 (Weld Cooling Time) 39 T6-8-20570 Wire Ass'y X4 (BRK) 40 T6-8-20590 Wire Ass'y X0 4 T6-8-20580 Earth Plate (4P) 42 TMS042 TMS, M4 2 43 TMS0308 TMS, M3 8 4 45 PMS030 PMS, M3 0 2 SEE PAGE 7 46 PMS0320 PMS, M3 20 4 SEE PAGE 4 47 PMS0325 PMS, M3 25 2 SEE PAGE 7 50 SW03 SW, M3 8 SEE PAGE 4, 7 53 PW04 PW, M4 2 60 T6-6-3038 Connector (Socket)(Heater) 6 T6-6-30350 Power Cable 62 T6-6-0352 Connector (Socket)(Power) - 22 -
REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-8-202 Electric Control Group (For TP-60D3, 220V) T6-8-2022 Electric Control Group (For TP-60D3, 380V/400V/45V) T6-8-20 Box 2 T6-8-220 Cover 3 LA-20090 Label 4 T6-6-3004 Transformer 5 T6-8-250 P.C.Board (For 50HZ, 3Phase) T6-8-260 P.C.Board (For 60HZ, 3Phase) 7 T6-6-30047 EMI Filter 8 T6-6-0355 Connector (Plug)(Power) 9 T6-6-3008 Connector (Heater) 0 T5-4-023 Variable Resistor (5K)( 3) T5-4-022 Knob 2 T5-4-060 Fuse Holder 6 3 T6-6-30034 Fuse (7A) 3 4 T6-6-3003 Fuse (2A) 2 5 T6-6-30036 Fuse (A) 6 TMS0306 TMS, M3 6 4 7 TMS0508 TMS, M5 8 4 8 T6-8-2006 Electric Control Group (Without Wire Ass'y) 9 T6-8-2290 Transformer (For 380V/400V/45V) 20 T6-8-2300 Transformer Cover (For 380V/400V/45V) 2 HBS050 HBS, M5 0 (For 380V/400V/45V) 3 22 PW05 PW, M5 (For 380V/400V/45V) 3 23 HBS052 HBS, M5 2 (For 380V/400V/45V) 24 T6-6-30200 Earth Plate (3P)(For 380V/400V/45V) 25 TMS0408 TMS, M4 8 (For 380V/400V/45V) 4 26 PMS0306 PMS, M3 6 4 27 PMS042 PMS, M4 2 2 28 SW04 SW, M4 3 29 HN04 HN, M4 3 30 T6-8-2452 Wire Ass'y X (Motor M)
7-3-2 ELECTRIC CONTROL GROUP T6-8-202 (For TP-60D3) T6-8-2022 REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 3 T6-8-2453 Wire Ass'y X2 (Motor M2) 32 T6-8-2454 Wire Ass'y X3 (Motor M3) 33 T6-8-20470 Wire Ass'y X4 (Motor M5) 34 T6-8-20480 Wire Ass'y X5 (Motor M5-) 35 T6-8-5068 Proximity Sensor (X6, X9-)(LS6, 2 SEE PAGE 7 S.F.S.) 36 T7--20350 Photo Eye (X7)(PH) SEE PAGE 9 37 T6-8-2050 Wire Ass'y X8 (Control Panel) 38 T6-8-20520 Wire Ass'y X9 (LS4/LS5/Foot Switch) 39 T6-8-20530 Wire Ass'y X0 (T) 40 T6--068 Proximity Sensor (X, X2)(LS2, 2 SEE PAGE 4 LS3) 4 T6-6-0354 Connector (Socket)(Power) 42 T6-8-20560 Wire Ass'y X3 (Weld Cooling Time) 43 T6-8-20570 Wire Ass'y X4 (BRK) 45 T6-6-3035 Power Cable (For 220V) T6-6-30352 Power Cable (For 380V/400V/45V) 46 T6-8-20580 Earth Plate (4P) 47 T6-6-30353 Power Cable (For 380V/400V/45V) 48 T6-8-2023 Electric Control Group (With Wire Ass'y)(For 220V) T6-8-2024 Electric Control Group (With Wire Ass'y)(For 380V/400V/45V) 49 T6-6-3038 Connector (Socket)(Heater) 50 T6-8-2059 Wire Ass'y X0 5 TMS042 TMS, M4 2 52 TMS0308 TMS, M3 8 4 53 PW04 PW, M4 2 55 PMS030 PMS, M3 0 2 SEE PAGE 7 56 PMS0320 PMS, M3 20 4 SEE PAGE 4 57 PMS0325 PMS, M3 25 2 SEE PAGE 7 60 SW03 SW, M3 8 SEE PAGE 4, 7 6 SW05 SW, M5 (For 380V/400V/45V) 3-25 -
REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-8-20007 Electric Control Group (For 0V) T6-8-20029 Electric Control Group (For 220V) T6-8-20030 Electric Control Group (For 240V) T6-8-20 Box 2 T6-8-220 Cover 3 LA-20086 Label 4 T6-6-3004 Transformer 5 T6-8-2052 P.C.Board (For 50HZ, Phase) T6-8-206 P.C.Board (For 60HZ, Phase) 7 T6-6-30047 EMI Filter 8 T6-6-0353 Connector (Plug)(Power) 9 T6-6-3008 Connector (Heater) 0 T5-4-023 Variable Resistor (5K)( 3) T5-4-022 Knob 2 T5-4-060 Fuse Holder 6 3 T6-6-30033 Fuse (5A)(For 220V/230V/240V) 2 T6-6-3033 Fuse (0A)(For 0V) 2 4 T6-6-30034 Fuse (7A)(For 220V/230V/240V) T6-6-3033 Fuse (0A)(For 0V) 5 T6-6-3003 Fuse (2A) 6 T6-6-30036 Fuse (A) 7 T6-6-3003 Fuse (2A)(For 220V/230V/240V) T6-6-30032 Fuse (3A)(For 0V) 8 T6-8-20009 Electric Control Group (Without Wire Ass'y)(For 0V) T6-8-2003 Electric Control Group (Without Wire Ass'y)(For 220V) T6-8-20032 Electric Control Group (Without Wire Ass'y)(For 240V) 9 TMS0306 TMS, M3 6 4 20 TMS0508 TMS, M5 8 4 2 PMS0306 PMS, M3 6 4 22 PMS042 PMS, M4 2 2 23 SW04 SW, M4 3 24 HN04 HN, M4 3
REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 25 T6-8-2044 Wire Ass'y X (Motor M) 26 T6-8-2045 Wire Ass'y X2 (Motor M2) 27 T6-8-2046 Wire Ass'y X3 (Motor M3) 28 T6-8-2047 Wire Ass'y X4 (Motor M5) 29 T6-8-2048 Wire Ass'y X5 (Motor M5-) 30 T7-6-080 Proximity Sensor (X6, X9-)(LS6, 2 SEE PAGE 7 S.F.S.) 3 T7--20350 Photo Eye (X7)(PH) SEE PAGE 9 32 T6-8-205 Wire Ass'y X8 (Control Panel) 34 T6-8-20523 Wire Ass'y X9 (LS4/LS5/Foot Switch) 35 T6-8-2053 Wire Ass'y X0 (T) 36 T7-6-0790 Proximity Sensor (X, X2)(LS2, 2 SEE PAGE 4 LS3) 38 T6-8-2056 Wire Ass'y X3 (Weld Cooling Time) 39 T6-8-2057 Wire Ass'y X4 (BRK) 40 T6-8-2690 Bridge Rectifier (BR5002) 4 T6-8-20580 Earth Plate (4P) 42 MV-6-0030 Transformer (Control)(For 0V) MV-6-003 Transformer (Control) (For 220V/230V/240V) 43 T6-8-2009 Electric Control Group (With Wire Ass'y)(For 0V) T6-8-20033 Electric Control Group (With Wire Ass'y)(For 220V) T6-8-20034 Electric Control Group (With Wire Ass'y)(For 240V) 44 T6-6-0352 Connector (Socket)(Power) 45 T6-6-30354 Power Cable 46 T6-6-3038 Connector (Socket)(Heater) 47 T6-8-20590 Wire Ass'y X0 49 TMS0308 TMS, M3 8 4 50 TMS0408 TMS, M4 8 4 5 TMS042 TMS, M4 2 53 PMS030 PMS, M3 0 2 SEE PAGE 7
REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 54 PMS0320 PMS, M3 20 4 SEE PAGE 4 55 PMS0325 PMS, M3 25 2 SEE PAGE 7 56 PW04 PW, M4 2 57 PW05 PW, M5 60 SW03 SW, M3 8 SEE PAGE 4, 7 6 SW05 SW, M5 65 HBS056 HBS, M5 6
REF. NO. PART NO. DESCRIPTION Q'TY REMARKS T6-8-207 Electric Control Group (For TP-60L3, 220V) T6-8-208 Electric Control Group (For TP-60L3, 380V/400V/45V) T6-8-20 Box 2 T6-8-220 Cover 3 LA-20090 Label 4 T6-6-3004 Transformer 5 T6-8-25 P.C.Board (For 50HZ, 3Phase) T6-8-26 P.C.Board (For 60HZ, 3Phase) 7 T6-6-30047 EMI Filter 8 T6-6-0355 Connector (Plug)(Power) 9 T6-6-3008 Connector (Heater) 0 T5-4-023 Variable Resistor (5K)( 3) T5-4-022 Knob 2 T5-4-060 Fuse Holder 6 3 T6-6-30034 Fuse (7A) 3 4 T6-6-3003 Fuse (2A) 2 5 T6-6-30036 Fuse (A) 6 TMS0305 TMS, M3 5 4 7 TMS0508 TMS, M5 8 4 8 T6-8-2008 Electric Control Group (Without Wire Ass'y) 9 T6-8-2290 Transformer (For 380V/400V/45V) 20 T6-8-2300 Transformer Cover (For 380V/400V/45V) 2 HBS050 HBS, M5 0 (For 380V/400V/45V) 3 22 PW05 PW, M5 PW, M5 (For 380V/400V/45V) 4 23 HBS056 HBS, M5 6 HBS, M5 6 (For 380V/400V/45V) 2 24 T6-6-30200 Earth Plate (3P)(For 380V/400V/45V) 25 TMS0408 TMS, M4 8 4 26 PMS0306 PMS, M3 6 4 27 PMS042 PMS, M4 2 2 28 SW04 SW, M4 3
REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 29 HN04 HN, M4 3 30 T6-8-2455 Wire Ass'y X (Motor M) 3 T6-8-2456 Wire Ass'y X2 (Motor M2) 32 T6-8-2046 Wire Ass'y X3 (Motor M3) 33 T6-8-2047 Wire Ass'y X4 (Motor M5) 34 T6-8-2048 Wire Ass'y X5 (Motor M5-) 35 T7-6-080 Proximity Sensor (X6, X9-)(LS6, 2 SEE PAGE 7 S.F.S.) 36 T7--20350 Photo Eye (X7)(PH) SEE PAGE 9 37 T6-8-205 Wire Ass'y X8 (Control Panel) 38 T6-8-20523 Wire Ass'y X9 (LS4/LS5/Foot Switch) 39 T6-8-2053 Wire Ass'y X0 (T) 40 T7-6-0790 Proximity Sensor (X, X2)(LS2, 2 SEE PAGE 4 LS3) 4 T6-8-2059 Wire Ass'y X0 42 T6-8-2056 Wire Ass'y X3 (Weld Cooling Time) 43 T6-8-2057 Wire Ass'y X4 (BRK) 45 MV-6-003 Transformer (Control) 46 T6-8-20580 Earth Plate (4P) 47 T6-8-203 Electric Control Group (With Wire Ass'y)(For 220V) T6-8-2032 Electric Control Group (With Wire Ass'y)(For 380V/400V/45V) 48 PMS030 PMS, M3 0 2 SEE PAGE 7 49 PMS0320 PMS, M3 20 4 SEE PAGE 4 50 PMS0325 PMS, M3 25 2 SEE PAGE 7 5 TMS042 TMS, M4 2 52 TMS0308 TMS, M3 8 4 53 PW04 PW, M4 2 54 T6-6-3038 Connector (Socket)(Heater) 55 T6-6-30352 Connector (Socket)(Power) 56 T6-6-30355 Power Cable (For 220V) T6-6-30356 Power Cable (For 380V/400V/45V) 57 T6-6-30357 Power Cable (For 380V/400V/45V) 58 T6-8-2690 Bridge Rectifier (BR5002)
REF. NO. PART NO. DESCRIPTION Q'TY REMARKS 65 SW03 SW, M3 8 SEE PAGE 4, 7 66 SW05 SW, M5 SW, M5 (For 380V/400V/45V) 4