SPRINGFIELD ARMORY 1911-A1 PISTOLS OPERATION AND SAFETY MANUAL

SPRINGFIELD ARMORY 1911-A1 PISTOLS OPERATION AND SAFETY MANUAL Important Safety Information Inside Read this manual before handling this firearm. Keep this manual with your firearm and review it before each use. This manual was designed to fit in your shirt or jacket pocket. Do not allow others to handle or fire your firearm until they have read this manual. Transfer this manual with the firearm upon ownership change. Be a responsible firearm owner. Use it safely, store it securely, and always transfer a firearm responsible and legally. Download this manual on our website: www.springfieldarmory.com

CONTENTS Read and Understand this Manual...3 Know Your Gun...4 Safety Rules...5 Loaded Chamber Indicator...12 Springfield s Integral Locking System (ILS)...13 Loading...18 Firing...19 Unloading...20 Hammer Lowering...22 Ported Barrel...46 Exploded View & Parts List Mil-Spec Models...48 Loaded Models....50 High Capacity Models....52 Micro-Compact Models...54 Point of Aim....56 Care and Cleaning...57 Warnings....60 & 61 Malfunction Warning...23 Disassembly and Assembly Section 1: Full-Size Models...25 Section 2: TRP Operator Models...31 Section 3: V-12, V-16, and Long Slide Models...35 Section 4: Micro-Compact, Ultra Compact, V-10, Compact, and Champion Models...40 2 If you have any questions concerning information in this manual, call Springfield's Consumer Safety Department at (309) 944-5631 for assistance.

BEFORE LOADING AND FIRING THIS FIREARM, READ AND UNDERSTAND THE INFORMATION IN THIS MANUAL. This is an auto loading firearm. It is immediately loaded and ready to fire again after each shot until all cartridges loaded in magazine have been fired. The firearm is able to fire both with and without the magazine in place. Removing the magazine does not unload the firearm nor does it engage a safety. The firearm is not unloaded until the magazine is removed and the chamber is empty. About your owner's manual This is an instruction booklet on how to operate this firearm with some basic safe handling rules. It does not attempt to provide information about using a firearm to defend yourself, how to hunt, or for competitive or target shooting. It is important to receive training from a competent firearms instructor prior to engaging in any of these activities. The National Rifle Association, your local or state authorities, or your firearm dealer may provide information regarding available instructors or training courses. If you have a license to carry concealed, never do so without prior instruction from a certified instructor. Using a firearm for self defense is a complex subject with dangers and risks for which you must be properly trained. Every safety rule has a reason behind it - read the rules carefully and understand why each is important for safety. It is recommended that every person receive instructions from a competent firearms instructor before handling this or any other firearm. Know and obey all firearm laws and regulations, which may vary from city to city and state to state. Do not give a firearm to someone who is not allowed to own a firearm or who may use it for a criminal purpose. Used firearms If you purchased this firearm as a used firearm, have it inspected and tested by a competent pistolsmith before you use it. Firearms are sometimes altered and may require repair before they can be used safely. Store firearms safely in the home Store firearms unloaded, locked and in a secure place. Obey firearm storage laws. Store firearms and ammunition separately. Because your children may be in other homes where firearms are stored, you should show them what to do if they see or find a firearm by showing them the Eddie Eagle video available from the NRA by calling (703) 267-1000. OBEY ALL GUN LAWS WHEN BUYING AND SELLING FIREARMS. NEVER BUY A GUN INTENDING TO TRANSFER IT TO SOMEONE WHO IS PROHIBITED FROM OWNING FIREARMS. NEVER EVER BE A "STRAW PURCHASER." 3

KNOW YOUR FIREARM Front Sight Barrel Bushing Slide Plunger Tube Rear Sight Delta Hammer Barrel Thumb Safety Full-Length Guide Rod Disassembly Notch Slide Stop Trigger Trigger Guard Magazine Release Grip Safety ILS Housing 4 Magazine Well

SAFETY RULES READ AND UNDERSTAND THESE SAFETY RULES Be A Safe Firearm Owner. ACCIDENT (ak si dent) N. 1. An unintentional or unexpected happening that is undesirable or unfortunate, especially one resulting in injury, damage, harm or loss. Don t be the cause of an accident. A responsible firearm owner is safety minded and always handles firearms in a safe manner by following the basic rules of safe shooting and by using common sense in the handling of a firearm. Store firearms unloaded, locked, and in a secure place. Keep keys for locks separate from lock and in a secure place away from children. Keep firearms out of reach of children. You are responsible for children s safety. Be A Responsible Firearm Owner. treat all firearms as if they are loaded at all times. Although many safety mechanisms are designed into your firearm, firearm safety still depends on you being a responsible firearms owner. never point a firearm at any person or thing you do not intend to shoot. Be sure you have positively identified your target. Always keep the muzzle pointed in a safe direction. Do not drop your firearm. Make sure you maintain control of your firearm at all times. If it falls, it may fire. If you do drop it, unload it and examine it to be sure it works correctly. Do not attempt to fire it again until you have completed this safety check. Never put your hand over the muzzle of the firearm. Keep your finger(s) off the trigger and out of the trigger guard until you are actually aiming at your target, and made the decision to fire. Under no circumstances should the owner of this firearm allow it to come into possession of or be handled by small children or a mentally handicapped individual. Do not cover the ejection port with your hands when loading/unloading your firearm. 5

BE A RESPONSIBLE FIREARM OWNER! never rely on a firearm s safety features to protect you from unsafe firearm handling. A safety is only a mechanical device, not a substitute for common sense. Keep your finger off the trigger until you are on target and have made the DECISION to fire. Be sure of your target and backstop before you shoot. Ask yourself what your bullet will hit if it misses or goes through the target. Before shooting, be sure the barrel is clear of obstructions, including excessive oil and grease. Do not let water, snow, mud or other materials enter the barrel. Do not pull a firearm toward you by the muzzle. Always hold your firearm so you control the direction of its muzzle in case you fall or stumble. ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION. If anything does get into the barrel, remove cartridges, and clean bore immediately before attempting to shoot. Obstructed barrels can burst and injure you and/or bystanders. Maintain possession of your firearm at all times when you are on the firing range or during target practice. DO NOT ALLOW OTHERS TO HANDLE YOUR FIREARM UNLESS THAT PERSON IS BEING INSTRUCTED OR TRAINED. Do not cover the ejection port with your hands when loading/unloading your firearm. 6 The 1911-A1 pistol, like all firearms, is a dangerous weapon if not handled properly.

BE A SAFE SHOOTER! Always keep the muzzle pointed in a safe direction. Firearms and alcohol or drugs do not mix. Do not take them before or during shooting activities. Your vision, coordination and judgment could be impaired, making firearm handling unsafe. When taking medication, seek a doctor s advice to be sure you can operate and handle your firearm safely. Receive training from a competent firearms instructor before using any firearm. Before attempting to shoot, practice operations by using snap caps (dummy rounds). Become familiar with the safety features, trigger control, and handling of the firearm. Make sure you maintain control of your firearm at all times. Always keep and carry your firearm with an empty chamber until you intend to shoot, so your firearm cannot be fired unintentionally. Firearms should be unloaded when not in use. This means both the chamber and magazine are empty. When transferring a firearm by hand, always open the action and check to assure that it is unloaded prior to handing it over to someone. Never take anyone s word that a firearm is unloaded. When receiving a firearm, always open the action and check that it is unloaded. 7

READ THESE RULES! 8 Load firearm only when on range preparing to fire. Unload it before leaving range. Treat every firearm as if it is loaded... all the time! Load and unload with the firearm muzzle pointed in a safe direction. Be certain firearm is unloaded before cleaning. Completely unload your firearm before storing, travelling, standing it against an object, laying it down, entering a house, car, truck, boat, RV/camper, building, or handing it to someone. Never leave a loaded firearm unattended. Tragedy may result if a child finds your firearm and plays with it. Keep every firearm secure. Children do not believe firearms can kill. Store firearms and ammunition separately. Both should be placed beyond children s reach. Obey all laws regarding the storage and security of firearms in the home. Know and obey the laws regarding the transportation and carrying of firearms. Never carry any firearm, loaded or unloaded, in your pocket, purse or tucked in your belt or waistband. Use a firearm case or a proper holster. Old or reloaded ammunition may cause damage to the firearm and/or injure you or others. Use only clean, dry, original, high-quality, commercially manufactured ammunition. Using reloaded ammunition may void the warranty. ALWAYS REMEMBER, REMOVING THE MAGAZINE DOES NOT UNLOAD THE PISTOL NOR DOES IT ENGAGE A SAFETY. ALWAYS REMEMBER, THE PISTOL IS NOT UNLOADED UNTIL THE MAGAZINE IS REMOVED AND THE CHAMBER IS EMPTY. always remember, this firearm is able to fire with or without the magazine in place. Do not cover the ejection port with your hands when loading/unloading your firearm.

TREAT EVERY FIREARM AS IF IT IS LOADED... ALL THE TIME! Many ammunition identifications sound similar. Make sure you use the right caliber/size ammunition in your firearm. If firearm fails to fire when the trigger is pulled, keep it pointed at the target for at least 30 seconds. Remove the magazine before opening the action. Remove the cartridge from the chamber. Sometimes slow primer ignition will cause a hang fire and the cartridge will go off after a short pause. When group firing, always appoint someone to maintain safety control. Obey his/her commands immediately and completely. While person is loading, firing, and unloading, spectators need to remain behind the users. Always wear protective glasses when shooting. Always wear hearing protection when shooting. never shoot at hard flat surfaces or water; bullets will ricochet unpredictably. Do not alter or modify your firearm. Have your firearm serviced regularly by a qualified pistolsmith. Discharging firearms in poorly ventilated areas, cleaning firearms, or handling ammunition may result in exposure to lead and other substances known to cause birth defects, reproductive harm, cancer and other serious physical injury. Have adequate ventilation at all times. Wash hands thoroughly after firing your firearm, after cleaning your firearm, or whenever you have handled ammunition. Always use quality ammunition. ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION. Do not cover the ejection port with your hands when loading/unloading your firearm. Always wear eye and ear protection when using any firearm. Safety and instruction manuals are available from Springfield, Inc. 9

BE A SAFE SHOOTER! 10 Do not try to change your firearm s trigger pull, because alterations of trigger pull usually affect sear engagement and might cause accidental firing. never use a firearm that jams or fails to function properly. Should this occur, return to Springfield, Inc. for warranty/repair. If your shot sounds weak or underpowered, it could mean a bullet is in the chamber/bore. The firearm should be immediately unloaded and the chamber/ bore checked for obstructions before re-firing. DO NOT "HORSEPLAY" with a firearm. Your firearm cannot think...but you can. Firearm safety depends on you. Write or call us concerning any items you do not understand and/or which might relate to your safety and the safe operations of any of our products. Springfield, Inc. Consumer Safety Department 420 West Main Street Geneseo, IL 61254 1-800-680-6866 Important Warning There is no safe way to discharge a firearm in a home or apartment. Bullets will go through walls, floors, furniture, and appliances and still cause serious injury or death to persons in the house, next door, or outside. Accidental discharges indoors ALWAYS result in property damage or personal injury. WARNING: When you squeeze the trigger, you must expect the firearm to fire. You must take full responsibility for firing it. Your care can avoid accidental discharge and thereby avoid accidental injury and death.

HANDLING We want you to be a safe, satisfied shooter. Before attempting to load this firearm with live ammunition, follow the sequence of operations shown here without ammunition or with dummy shells. By practicing operations with snap caps (or with dummy rounds), you will become familiar with: Safety features, Trigger control (snap caps), Handling of your firearm. As a result you will be a safer, more confident shooter when aiming at your first target. Safety Stop on Hammer The Safety Stop is a flat, shelf-like surface on the hammer which functions automatically. It will engage the sear in the unlikely event of primary sear notch failure. This will prevent the hammer from falling fully forward unintentionally and will insure against uncontrolled automatic fire. It also prevents the hammer from striking the firing pin should your hand slip from the slide or hammer while cocking the pistol, provided the hammer is rotated past the Safety Stop. It is located such that when the sear engages the Safety Stop, the sear can be disengaged by squeezing the trigger. It falls because the sear slides over the flat part of the safety stop to release the hammer. This is intentional but will not allow the pistol to fire. It will not fire because the hammer is almost fully forward when it is released from the sear. The Safety Stop is not a manual safety and should not be engaged by hand. Do not carry the firearm while Safety Stop is engaged. Caution: Control hammer with your thumb and forefinger (Figure 1). Always point pistol in a safe direction when squeezing the trigger to lower the hammer. This will avoid accidental injury in the unlikely event of firearm discharge. Lowering the hammer in this way should be done only when the chamber is empty. Figure 1 11

LOADED CHAMBER INDICATOR Springfield pistols sold after January, 2001 have a loaded chamber indicator. (See Figure 1.) The barrel slot allows you to observe whether a shell is in the chamber. When a shell is in the chamber the brass case can be seen clearly. Figure 1 12 Caution! Even though the chamber is empty there may be shells in the magazine. The firearm is not completely empty until both the chamber and magazine are empty.

SPRINGFIELD S INTEGRAL LOCKING SYSTEM (ILS) US PAT.6269576 Warning: Do not remove the mainspring housing before reading instructions and using eye protection. The ILS has parts under spring pressure. If improperly disassembled, the mainspring cap will be forceably ejected and could cause injury to you or a bystander. Caution: The ILS is designed to lock the pistol when stored or left unattended. It is not intended to replace any of the existing safety features. ILS Operation Locate the ILS switch on your mainspring housing. (See Figure 13) 1. If the holes are vertical (stacked) the firearm is not locked. (See Fig. 13-1) To activate the ILS and lock your firearm, follow these steps. Point the firearm in a safe direction. Unload the gun. (See page 20) Fully lower the hammer (see page 22). Insert the key and turn clockwise until the holes are horizontal (side-by-side). The ILS is now activated and the firearm is locked. (See Fig. 13-2) ILS switch Figure 13 2. If the holes are horizontal (side-by-side) the gun is locked. To unlock, follow these steps. Point the firearm in a safe direction. Insert the key and turn counterclockwise until the holes are vertical or stacked. (see Fig. 13-3) Before cocking the firearm make sure it is unloaded. Note: The ILS requires firm pressure to operate, but do not over-torque. Fig.13-1 Fig.13-2 Fig.13-3 13

SPRINGFIELD S INTEGRAL LOCKING SYSTEM (ILS) US PAT.6269576 Removing the Mainspring Housing with ILS Caution: Always be sure the firearm is unloaded before proceeding. 1. With the hammer full down, deactivate the ILS. The holes should be vertical (or stacked). (Fig. 13-1) 2. Wrap a heavy-duty rubber band around the grip safety until it is completely depressed. Doing so will maintain the alignment of the sear spring and negate further disassembly of the firearm. (Fig. 14) 3. Cock the hammer to the full cocked position. 4. Insert takedown pin into takedown hole. (Fig. 14) 5. Slowly lower the hammer to the full-down (fired) position. 6. With a proper punch, drive out the mainspring housing retaining pin. 7. Remove the mainspring housing. Figure 14 14 Caution: Do not remove the takedown pin until the mainspring housing is reinstalled.

SPRINGFIELD S INTEGRAL LOCKING SYSTEM (ILS) US PAT.6269576 Disassembly of the Mainspring Housing with ILS Do not attempt this procedure unless you have considerable experience in firearms disassembly. 1. Place mainspring housing in a vice. 2. With a suitable punch, depress the ILS spring cap and hold it down. (Figure 15-1) 3. While continuing to depress the ILS spring cap, remove the takedown pin. (Fig. 15-2) 4. Slowly and carefully release the pressure on the spring cap allowing it to move out of the mainspring housing. (Fig. 15-3) 5. After the spring cap has been removed, the mainspring and mainspring retainer can be removed. Caution: Do not turn the locking pin when the ILS is disassembled. The system may be reassembled only with the ILS pin deactivated (with the holes vertical or stacked). Fig. 15-1 Fig. 15-2 Fig. 15-3 This procedure requires extreme caution. The ILS spring cap is under extreme pressure and will be ejected if you fail to perform the disassembly properly. Use extreme care and wear eye protection. 15

SPRINGFIELD S INTEGRAL LOCKING SYSTEM (ILS) US PAT.6269576 Reassembly of the Mainspring Housing with ILS 1. Assemble the mainspring cap, mainspring, and mainspring retainer then insert into the mainspring housing. (See Figure 16) 2. Carefully depress the cap far enough to allow you to reinstall the takedown pin. (See Fig.16-1). 3. Carefully and slowly release the pressure on the spring cap until the takedown pin captures it. 16 Figure 16 Figure 16-1

SPRINGFIELD S INTEGRAL LOCKING SYSTEM (ILS) US PAT.6269576 Replacing the Mainspring Housing with ILS 1. Slide the mainspring housing into place and reinsert the mainspring housing retaining pin. 2. Cock the hammer to a full cock position. 3. Remove the takedown pin. 4. Remove the rubberband from the grip safety. 5. Lower the hammer to the full down position. The mainspring housing with ILS is now installed. 17

LOADING/PREPARING TO FIRE 18 1. Place the EMPTY magazine in the magazine well, located in bottom of pistol grip. Make sure the magazine is EMPTY or you will inadvertency load the firearm. Push firmly enough on bottom of magazine to make sure it is properly seated. A distinctive click will confirm the magazine has been properly inserted. Pull the slide all the way to the rear, until it locks back. 2. Depress magazine release and remove magazine. Place rim of first cartridge on front of follower Then push down on the follower and slide cartridge under the lips of the magazine and to the rear. Load successive rounds the same way. Use only clean, dry, original, high-quality, commercially manufactured ammunition. 3. Re-insert magazine into magazine well, located in bottom of pistol grip. Push firmly enough on bottom of magazine to make sure it is properly seated. 4. Point firearm in a safe direction, keep finger off trigger and out away from trigger guard. Pull slide back and release slide smartly to allow slide to move forward and load a shell from the magazine into the chamber. Warning! Always load ammo from the magazine to prevent damage to trigger and sear. Never touch the trigger when loading or unloading the firearm. Never load a firearm in your house or car. Only at a firing range.

FIRING Point gun in a safe direction at all times If you have never fired a gun before, practice without live ammunition before your first shot. Then load only one cartridge into the magazine for your first live ammunition firing. 1. Load shell into chamber from magazine and engage the thumb safety. 2. Grasp grip of pistol firmly. (A loose grip may cause the pistol to malfunction.) The pressure from the hand will disengage grip safety located at top of rear grip area. 3. Move thumb safety down taking gun off safety. Caution: The gun is now ready to fire. Be prepared for noise and recoil when pistol fires. 4. Aim gun at target by aligning sights. 5. Lightly place finger on trigger, and slowly squeeze trigger. Spent cartridge is expelled up and to the right. 6. Pistol will automatically be ready to fire again after each shot until all cartridges loaded in magazine have been fired. 7. When last cartridge has been fired, slide will lock open and remain to rear. Warning! Improperly loading the 1911 by manually inserting a round in the chamber may cause accidental discharge. Always load the pistol using the magazine. When loading the pistol, always point the muzzle in a safe direction. 19

UNLOADING Figure 20-1 If slide is already in locked back position: 1. Point gun in safe direction. 2. Press magazine release button to remove magazine. 3. From top and rear, carefully inspect chamber to make sure it is empty (Figure 20-1). 4. Hold slide, disengage slide stop, ease slide forward. Notice: The slide of a 1911-A1 pistol should never be released on an empty chamber; especially one which has had an action job. Releasing the slide on an empty chamber causes damage to the breech face on the barrel and undue stress on all action parts, including the hammer and the sear. This will ruin the action job performed on your pistol. 5. Carefully lower hammer as described in the HAMMER LOWERING section. (Figure 20-2) Figure 20-2 20 Pistol is not empty or unloaded until the chamber is empty and the magazine removed.

UNLOADING Figure 21-1 If slide is forward and hammer is cocked: 1. Point gun in safe direction. 2. Engage thumb safety. 3. Press magazine release button to remove magazine. 4. Disengage thumb safety. 5. Pull slide fully to rear to eject any cartridge remaining in chamber. 6. While holding slide in rearward (open) position, carefully inspect chamber making sure it is empty (Figure 21-2). 7. Slowly release slide, allowing it to return to forward position. 8. Carefully lower hammer as described in HAMMER LOWERING section (Figure 21-2). When magazine has been removed and when chamber is empty, the ILS may be activated or a gun lock can be installed. Pistol can now be safely stored in a secure place. Figure 21-2 Pistol is not empty or unloaded until the chamber is empty and the magazine removed. Never touch the trigger when loading or unloading the pistol. 21

HAMMER LOWERING Figure 22-1 1. Point gun in safe direction and ensure pistol is unloaded (Figure 22-1). 2. Firmly hold gun, depressing grip safety. 3. Using non-shooting hand, firmly grasp hammer with thumb and forefinger (Figure 22-2). 4. Be prepared for hammer movement. Squeeze trigger. 5. Slowly lower hammer with thumb and forefinger until it is fully forward. 6. Release trigger. (If the trigger is released early the gun may be on the Safety Stop.) Note: Always keep and carry your pistol with an empty chamber and with the hammer forward (down) until you intend to shoot, so your pistol cannot be fired unintentionally. 22 Caution: If pistol is loaded, gun may discharge if the hammer slips from your grip during this procedure. Figure 22-2

MALFUNCTION WARNING! If cartridge hangs up, jams or binds when being chambered from magazine into chamber, do not attempt to force it into chamber by pushing or striking slide. 1. What to do: Point gun in a safe direction. Remove magazine. Pull back on slide and allow cartridge to fall from gun. If cartridge does not fall free, pull slide back and lock it back. Carefully dislodge cartridge. If cartridge cannot be removed, carefully store your gun and take it to a gunsmith. 2. Most failures of cartridge to feed or chamber are the result of a damaged magazine, improper gun handling or defective ammunition. 3. Whatever the cause, a jammed cartridge can be a dangerous situation. Should shell be discharged while out of chamber, cartridge will rupture and fragments will be blown out of pistol with sufficient force to cause injury. If any information in this manual is not clear, call Springfield s Consumer Safety Department at (309) 944-5631 for assistance. Always wear eye and ear protection when using any firearm. Safety and instruction manuals are available from Springfield, Inc. Always have gun pointed in a safe direction. Failure to obey safety information may result in injury to you or others. 23

TO ELIMINATE MALFUNCTIONS 1. Change type/brand of ammunition and/or magazine. 2. If changing to another type/brand of ammunition and/or magazine does not at once result in smooth feeding of cartridges from magazine to chamber, the following steps should be taken: Make certain chamber and magazine are unloaded. Magazine should be removed first. Check chamber to be sure it and magazine well are clear of cartridges. Thoroughly clean magazine, paying particular attention to removing accumulated grease. Thoroughly clean breech mechanism of pistol. Use a bristle brush and solvent to remove grease and fouling from breech face, extractor, chamber and feed ramp. (See CARE AND CLEANING section for detailed instruction.) Check that magazine spring tension is adequate. The spring should hold the follower tightly against the lips of the magazine. Check that magazine lips are free of nicks and burrs and are not deformed. Remove excess oil and solvent from all cleaned components, load magazine and try pistol again. 24 Proceed slowly and exercise caution to prevent the discharge of a jammed cartridge. The discharge of a jammed cartridge could cause serious injury to you or bystanders.

SECTION 1: DISASSEMBLY OF FULL-SIZE MODELS If you decide to disassemble your Springfield pistol, do so properly. Improper disassembly and assembly will create unsafe conditions that could result in injury or death or a gun that simply will not work. Don t take chances. Do not attempt to disassemble this or any other firearm until you have received training and instructions from a competent gunsmith. 25

SECTION 1: DISASSEMBLY FULL-SIZE MODELS Step 1 - Magazine Removal & Chamber Check Point gun in a safe direction. 1. Press magazine catch and remove magazine. 2. Pull slide backwards and check that no cartridge is in the chamber. 3. Release slide allowing it to go to forward position. Step 2 - Recoil Spring Removal Point gun in a safe direction. 1. If your pistol contains a full length guide rod, use a 5/32 Allen wrench or a screwdriver to remove the front portion of guide rod. If your pistol does not contain a full length guide rod, skip to step 3. 2. Grip slide behind the front sight, resting pistol butt on top of your knee. 3. Move slide rearward, approximately 1/2 inch, grasp firmly to hold in place, and depress recoil spring plug with thumb. 4. Point muzzle away from face and rotate barrel bushing clockwise. 5. Do not rotate bushing off of plug unless you have control of plug and spring. 26 WARNING: Point muzzle away from face to prevent injury in the event plug is ejected by spring. 2. 3.

SECTION 1: DISASSEMBLY FULL-SIZE MODELS Step 3 Cautiously allow plug and recoil spring to move forward. Step 4 - Slide Stop Removal 1. Align disassembly notch on slide with slide stop. 2. Press slide stop shaft on right side of frame and remove slide stop by pulling it out of left side of frame. Always wear eye and ear protection when using any firearm. Safety and instruction manuals are available from Springfield, Inc. BE SAFE! Be sure pistol is unloaded before beginning disassembly! Wear eye protection, gun contains spring-loaded parts. 27

SECTION 1: DISASSEMBLY FULL-SIZE MODELS Step 5 - Slide Removal Pull slide forward in its guides and remove slide. Barrel, barrel bushing, recoil spring plug, recoil spring and guide will come with it. Step 6 - Recoil Spring Components Removal Remove recoil spring and guide through back side. Step 7 - Barrel Removal 1. Rotate barrel bushing to left of slide and remove it through the front. 2. Tilt barrel link forward and remove barrel from front of slide. Step 7-1 28 Step 7-2

SECTION 1: DISASSEMBLY FULL-SIZE MODELS Note: There are many after-market or accessory items for 1911 style pistols. After market accessories may void warranty. If you are not the original owner of your pistol or you are unclear on disassembling your pistol, call or write to Springfield Armory. Call Springfield Consumer Safety Department at (309) 944-5631 or write c/o: Springfield Inc. 420 West Main Street Geneseo, IL 61254 Improper disassembly may damage the firearm. Always consult an experienced gunsmith if you experience any difficulty or have any questions concerning assembly procedure. 29

SECTION 1: ASSEMBLY FULL-SIZE MODELS Assemble by reversing the order of disassembly. Note: When replacing recoil assembly (Step 6), be certain the recoil spring guide and recoil spring are aligned with the barrel before inserting in slide. Be sure to flip barrel link forward before installing slide assembly. Slide stop shaft must go through hole in barrel link. An improperly assembled firearm is dangerous and should not be fired. Always consult an experienced gunsmith if you experience any difficulty or have any questions concerning assembly procedure. 30

SECTION 2: DISASSEMBLY OF TRP OPERATOR MODELS If you decide to disassemble your Springfield pistol, do so properly. Improper disassembly and assembly will create unsafe conditions that could result in injury or death or a gun that simply will not work. Don t take chances. Do not attempt to disassemble this or any other firearm until you have received training and instructions from a competent gunsmith. 31

SECTION 2: DISASSEMBLY TRP OPERATOR MODELS Step 1 - Magazine Removal & Chamber Check Point gun in a safe direction. 1. Press magazine catch and remove magazine. 2. Pull slide backwards and check that no cartridge is in the chamber. 32 Improper disassembly may damage the firearm. Always consult an experienced gunsmith if you experience any difficulty or have any questions concerning assembly procedure.

SECTION 2: DISASSEMBLY TRP OPERATOR MODELS Step 2 - Slide Stop Removal 1. Align disassembly notch on slide with slide stop. 2. Press slide stop shaft on right side of frame. 3. Remove slide stop from left side. 4. Pull slide assembly forward off frame. Step 3 - Recoil Spring Assembly Removal 1. Push recoil spring assembly forward to expose a small, pin-sized hole. (Fig. 33-1) 2. Insert the provided pin (or cut a paper clip so that it extends 1/16 on both sides of guide rod) into pin hole. 3. Remove recoil spring housing from the rear of the slide. (Fig. 33-2) 4. Remove the barrel from the front of the slide. Figure 33-1 Figure 33-2 33

SECTION 2: ASSEMBLY TRP OPERATOR MODELS Assemble by reversing the order of disassembly. Note: Be sure to flip barrel link forward before installing barrel into slide. An improperly assembled firearm is dangerous and should not be fired. Always consult an experienced gunsmith if you experience any difficulty or have any questions concerning assembly procedure. 34 Model 1911-A1 Pistols are classified firearms and dangerous weapons. Injury or death to you or others may result from unsafe or improper use.

SECTION 3: DISASSEMBLY OF V-12, V-16, & LONG SLIDE MODELS If you decide to disassemble your Springfield pistol, do so properly. Improper disassembly and assembly will create unsafe conditions that could result in injury or death or a gun that simply will not work. Don t take chances. Do not attempt to disassemble this or any other firearm until you have received training and instructions from a competent gunsmith. 35

SECTION 3: DISASSEMBLY V-12, V-16, & LONG SLIDE MODELS Step 1 - Magazine Removal & Chamber Check Point gun in a safe direction. 1. Press magazine catch and remove magazine. 2. Pull slide backwards and check that no cartridge is in the chamber. BE SAFE! Be sure pistol is unloaded before beginning disassembly! Wear eye protection, gun contains spring-loaded parts. 36 An improperly assembled firearm is dangerous and should not be fired. Always consult an experienced gunsmith if you experience any difficulty or have any questions concerning assembly procedure.

SECTION 3: DISASSEMBLY V-12, V-16, & LONG SLIDE MODELS Step 2 - Full Length Guide Rod Removal V-series and Long Slide Models contain full-length guide rods. 1. Use a 5/32 Allen wrench to remove the front portion of the guide rod. Step 4 - Slide Removal Pull slide forward in its guides and remove slide. Barrel, recoil spring plug, recoil spring, and guide will come with it. Step 3 - Slide Stop Removal 1. Align disassembly notch with slide stop. 2. Press slide stop shaft on right side of slide and remove slide stop by pulling it out of left side of frame. Recoil spring guide could eject out from the side as slide is removed. To keep the recoil spring from ejecting sideways, hold fingers around slide while moving it forward. 37

SECTION 3: DISASSEMBLY V-12, V-16, & LONG SLIDE MODELS Step 4 - Recoil Spring Components Removal Remove guide, recoil spring, and its plug through back of slide. Step 5 - Barrel Removal Tilt barrel link forward and remove barrel through front of slide. 38

SECTION 3: ASSEMBLY V-12, V-16, & LONG SLIDE MODELS Assemble by reversing the order of disassembly. Note: When replacing recoil assembly (Step 4), be certain barrel clearance cuts on recoil spring guide are aligned before inserting in slide. Be sure to flip barrel link forward before installing slide assembly. Note: 1911-A1 Ultra-Compact Pistols are designed to use standard pressure ball ammo and self defense loads. +P ammunition is not recommended in pistols shorter than 5 inches. Use only clean, dry, original, high-quality, commercially manufactured ammunition. An improperly assembled firearm is dangerous and should not be fired. Always consult an experienced gunsmith if you experience any difficulty or have any questions concerning assembly procedure. 39

SECTION 4: DISASSEMBLY of MICRO-COMPACT, ULTRA COMPACT, V-10, COMPACT, & CHAMPION MODELS 40 If you decide to disassemble your Springfield pistol, do so properly. Improper disassembly and assembly will create unsafe conditions that could result in injury or death or a gun that simply will not work. Don t take chances. Do not attempt to disassemble this or any other firearm until you have received training and instructions from a competent gunsmith.

SECTION 4: DISASSEMBLY MICRO-COMPACT, ULTRA COMPACT, V-10, COMPACT, & CHAMPION MODELS Step 1 - Magazine Removal & Chamber Check Point gun in a safe direction. 1. Press magazine catch and remove magazine. 2. Pull slide backwards and check that no cartridge is in the chamber. 3. Release slide allowing it to go to forward position. WARNING: Point muzzle away from face to prevent injury in the event plug is ejected by spring. 41

SECTION 4: DISASSEMBLY MICRO-COMPACT, ULTRA COMPACT, V-10, COMPACT, & CHAMPION MODELS Step 2 - Recoil Spring Removal Point gun in a safe direction. 1. Lock slide to the rear. (See fig. 57-1) 2. Firmly snap the takedown piece over the exposed portion of the guide rod between inner spring plug and guide rod cap. (See fig. 57-2) 3. Grasp slide, release slide lock and slowly allow slide to go forward. Align disassembly notch on slide with stop. Remove the slide stop. 4. Carefully remove the slide assembly from the receiver. 5. The recoil spring system can now be removed from the slide. (See fig. 57-3) 6. The barrel can now be removed from the front of the slide. 7. Disassembly is now complete. Figure 57-1 Figure 57-2 42 Figure 57-3

ALTERNATE METHOD FOR DISASSEMBLY 1. Retract slide to the takedown notch. 2. Align disassembly notch on slide with slide stop. 3. Remove slide stop and slowly remove slide from receiver keeping in mind that the slide is under spring pressure until it clears the receiver. 4. With the bottom of the slide facing up, press the guide rod head forward until enough of the rod is exposed and firmly snap the takedown piece over the rod. (See fig. 58-1 and 2) 5. The slide assembly can now be disassembled as previously laid out. (Described in section 4, Step 2). Figure 58-1 Figure 58-2 43

SECTION 4: ASSEMBLY MICRO-COMPACT, ULTRA COMPACT, V-10, COMPACT, & CHAMPION MODELS Assemble by reversing the order of disassembly. Note: Be sure to flip barrel link forward before installing barrel into slide. An improperly assembled firearm is dangerous and should not be fired. Always consult an experienced gunsmith if you experience any difficulty or have any questions concerning assembly procedure. 44 Model 1911-A1 Pistols are classified firearms and dangerous weapons. Injury or death to you or others may result from unsafe or improper use.

CAUTION Never leave pistol cocked and ready to fire as the fire condition is extremely dangerous. Pistol could easily be accidentally discharged causing injury, death, or damage to property. Proper use will prevent the gun from being fired accidentally. No mechanical device is a substitute for safe gun handling. Every household member should be trained in safe gun handling practices. Minor children should be given the Eddie Eagle Safety Program from the NRA. Call 703-267-1000 for the video. Caution: FIREARMS should always be locked and stored in complete compliance with all applicable laws and regulations. Always wear eye and ear protection when using any firearm. Safety and instruction manuals are available from Springfield, Inc. 45

PORTED BARREL SAFETY INSTRUCTIONS Warnings, Ammunition Restrictions, and Maintenance Completely read this safety manual before using a ported barrel pistol. Transfer this manual to any subsequent owner or user of the pistol. If you are inexperienced in the handling of firearms, obtain expert instruction before attempting to shoot. Neither this manual nor this product can take the place of proper instruction in the safety aspects of shooting, the use of firearms, and the use of a firearm for selfdefense. Severe injury to hands, eyes, face, other persons or property will occur with improper use of a ported pistol. Safety Notes Always use eye and ear protection when shooting or when in close proximity to shooting. A ported barrel pistol, in common with most pistols using muzzle brake devices, produces greater noise than normal pistols and this poses a danger to hearing. Never position any part of the body over or near the exhaust ports. Never cycle the slide with your hands over the exhaust ports. Never point a gun at anything you do not intend to shoot. If the ported pistol is drawn rapidly it must not be discharged in proximity to the holster or the shooter s eyes, legs, arms, clothing or bystanders. Do not shoot a ported barrel pistol from the hip. The blast from the exhaust ports can cause injury or property damage several feet away. Use caution when shooting to avoid overhead objects that may be damaged by the blast from the barrel exhaust ports. 46 Always point gun in a safe direction. Keep your gun unloaded until you are ready to shoot.

PORTED BARREL SAFETY INSTRUCTIONS Ammunition Use only fresh factory ammunition such as Winchester or Federal. DO NOT use handloads, reloads, or remanufactured ammunition in your Springfield firearm. Only shoot cartridges of the caliber engraved on the barrel. DO NOT use shot cartridges or any ammunition which is loaded with a frangible projectile or any ultra-light weight projectile at elevated velocities, or any wooden or plastic projectile. Maintenance Accumulated debris in the barrel exhaust ports may result in damage to the pistol or injury to the shooter. With the gun unloaded, regularly inspect the bore and exhaust ports for dirt and debris. Never discharge the firearm when any form of debris is present in the barrel or exhaust ports. Caution Fragments of the metal jackets on jacketed bullets may be propelled through the exhaust ports with great force and have the potential to cause injury or property damage at a distance of several feet. The misuse of any of the ammunition described above may result in injury, property damage, or both. Always wear eye and ear protection when using any firearm. Safety and instruction manuals are available from Springfield, Inc. 47

48 EXPLODED VIEW & PARTS LIST MIL-SPEC MODELS 1. PI9911.45 Mil-Spec Frame 1a. PI0037 Slide Stop 1b. PI0038 Thumb Safety 1c. PI0044 Slide Stop Plunger 1d. PI0042 Thumb Safety/Slide Stop Spring 1e. PI0043 Safety Plunger 1f. PI0041 Plunger Tube 1g. PI0017 Hammer Pin 1h. PI0015 Grip Screw Escutcheon 1i. PI0026 Mainspring Housing Retainer Pin 1j. PI4507.45 Ejector, Extended 1k. PI0005 Disconnector 1l. PI0034 Sear 1m. PI0027 Magazine Catch 1n. PI0029 Magazine Catch Spring 1o. PI0028 Magazine Catch Lock 1p. PI5006 Regular Spur Hammer 1q. PI0019 Hammer Strut Pin 1r. PI0018 Hammer Strut 1s. PI5308 Mil-Spec Trigger 1t. PI0036 Sear Spring 1u. PH5066 Grip Safety 1v. PI5143 Black Plastic Grip (L.H.) 1w. PI5144 Black Plastic Grip (R.H.) 1x. PI0014 Grip Screw 1y. PI0035 Sear Pin 1z. PI0008 Ejector Pin 2. PX4546.45 Slide 2a. PI5350 3-Dot Front Sight,.180 2b. PI5341 H.P. Fixed Rear Sight, 3-Dot 2c. PI0011 Extra Power Firing Pin Spring 2d. PI0910 9mm Titanium Firing Pin 2e. PI4506.45 Extractor 2f. PI4511.45 Firing Pin Stop 2g. PI0032 Recoil Spring Guide 2h. PI0030 Recoil Spring (16 lb.) 2i. PI0031 Recoil Spring Plug 3. PI3501.45 Barrel (Stainless) 3a. PI0004 Barrel Link Pin 3b. PI0003 Barrel Link 3c. PI3002 Barrel Bushing (Stainless) 4. PI4523.45 7-Round Magazine 5. PI0020 Arched Mainspring Housing 5a. SL0008 ILS Locking Bolt 5b. PI0024 Mainspring Retainer 5c. PI0052 Mainspring (28 lb.) 5d. SL0007 ILS Mainspring Cap 5e. SL0009 ILS Plunger 5f. SL0010 ILS Plunger Spring

49

50 EXPLODED VIEW & PARTS LIST LOADED MODELS 1. PI9911.45 Loaded Frame 1a. PI0037 Slide Stop 1b. PH5036 Extended Thumb Safety 1c. PI0044 Slide Stop Plunger 1d. PI0042 Thumb Safety/Slide Stop Spring 1e. PI0043 Safety Plunger 1f. PI0041 Plunger Tube 1g. PI0017 Hammer Pin 1h. PI0015 Grip Screw Escutcheon 1i. PI0026 Mainspring Housing Retainer Pin 1j. PI4507.45 Ejector, Extended 1k. PI0005 Disconnector 1l. PI0034 Sear 1m. PI0027 Magazine Catch 1n. PI0029 Magazine Catch Spring 1o. PI0028 Magazine Catch Lock 1p. PI5006 Delta-Style Hammer 1q. PI0019 Hammer Strut Pin 1r. PI0018 Hammer Strut 1s. PI5308 National Match Aluminum Trigger 1t. PI0036 Sear Spring 1u. PH5066 Beavertail Grip Safety 1v. PI5143 Cocobolo Checkered Grip w/bevel (L.H.) 1w. PI5144 Cocobolo Checkered Grip w/bevel (R.H.) 1x. PI0014 Grip Screw 1y. PI0035 Sear Pin 1z. PI0008 Ejector Pin 2. PX4546.45 Slide 2a. PI5017 Dovetail Front Sight 2b. PI4600M Fixed Combat Rear Sight 2c. PI0011 Extra Power Firing Pin Spring 2d. PI0910 9mm Titanium Firing Pin 2e. PI4506.45 Extractor 2f. PI4511.45 Firing Pin Stop 2g. PI5192 National Match 2-piece Recoil Spring Guide 2h. PI0030 Recoil Spring (16 lb.) 2i. PI5198 National Match Guide Plug (Stainless) 3. PI3501.45 Barrel (Stainless) 3a. PI0004 Barrel Link Pin 3b. PI0003 Barrel Link 3c. PI3002 Barrel Bushing (Stainless) 4. PI4523.45 7-Round Magazine 5. SL0005 ILS Mainspring Housing 5a. SL0008 ILS Locking Bolt 5b. PI0024 Mainspring Retainer 5c. PI0052 Mainspring (28 lb.) 5d. SL0007 ILS Mainspring Cap 5e. SL0009 ILS Plunger 5f. SL0010 ILS Plunger Spring

51

52 EXPLODED VIEW & PARTS LIST HIGH CAPACITY MODELS 1. PH9900 High-Capacity Frame 1a. PI0037 Slide Stop 1b. PH5036 Extended Thumb Safety 1c. PI0044 Slide Stop Plunger 1d. PI0042 Thumb Safety/Slide Stop Spring 1e. PI0043 Safety Plunger 1f. PI0017 Hammer Pin 1g. PH0015 Grip Screw Escutcheon 1h. PI0026 Mainspring Housing Retainer Pin 1i. PI4507.45 Ejectors, Extended 1j. PI0005 Disconnector 1k. PI0034 Sear 1l. PH0027 Magazine Catch 1m. PI0029 Magazine Catch Spring 1n. PI0028 Magazine Catch Lock 1o. PI5006 Delta Style Hammer 1p. PI0019 Hammer Strut Pin 1q. PI0018 Hammer Strut 1r. PH0039 High-Capacity Trigger 1s. PI0036 Sear Spring 1t. PH5066 Beavertail Grip Safety 1u. PH0006 High-Capacity Grip (L.H.) 1v. PH0007 High-Capacity Grip (R.H.) 1w. PH0014 High-Capacity Grip Screw 1x. PI0035 Sear Pin 1y. PI0008 Ejector Pin 2. PI4546.45 Slide 2a. PI5350 3-Dot Front Sight,.180 2b. PI5341 H.P. Fixed Rear Sight (3-Dot) 2c. PI0011 Extra Power Firing Pin Spring 2d. PI0910 9mm Titanium Firing Pin 2e. PI4506.45 Extractor 2f. PI4511 Firing Pin Stop 3. PI3501.45 Barrel (Stainless) 3a. PI0004 Barrel Link Pin 3b. PI0003 Barrel Link 3c. PI3002 Barrel Bushing (Stainless) 4. PI5445.45 High Capacity Standard Magazine 5. SL0005 ILS Mainspring Housing 5a. SL0008 ILS Locking Bolt 5b. PI0024 Mainspring Retainer 5c. PI0052 Mainspring (28 lb.) 5d. SL0007 ILS Mainspring Cap 5e. SL0009 ILS Plunger 5f. SL0010 ILS Plunger Spring

53

54 EXPLODED VIEW & PARTS LIST MICRO-COMPACT MODELS 1. PI9980.45 Micro-compact Frame 1a. PI0037 Slide Stop 1br. PH5114 Extended Ambidextrous Thumb Safety (Right) 1bl. PH5113 Extended Ambidextrous Thumb Safety (Left) 1c. PI0044 Slide Stop Plunger 1d. PI0042 Thumb Safety/Slide Stop Spring 1e. PI0043 Safety Plunger 1f. PI0041 Plunger Tube 1g. PI0017 Hammer Pin 1h. PI4815 Thin Line Grip Screw Escutcheon 1i. PI0026 Mainspring Housing Retainer Pin 1j. PI0907 Micro-Compact Ejector, Extended 1k. PI0005 Disconnector 1l. PI0034 Sear 1m. PI0027 Magazine Catch 1n. PI0029 Magazine Catch Spring 1o. PI0028 Magazine Catch Lock 1p. PI5006 Delta-Style Hammer 1q. PI0019 Hammer Strut Pin 1r. PI0018 Hammer Strut 1s. PI5308 National Match Aluminum Trigger 1t. PI0036 Sear Spring 1u. PH5066 Beavertail Grip Safety 1v. PI5168 Cocobolo Checkered Thin Line Grip w/bevel (L.H.) 1w. PI5169 Cocobolo Checkered Thin Line Grip w/bevel (R.H.) 1x. PI4814 Thin Line Grip Screw 1y. PI0035 Sear Pin 1z. PI0008 Ejector Pin 2. PI4845.45 Micro-Compact Slide 2a. PI5016M Dovetail Front Sight 2b. PI4600M Fixed Combat Rear Sight 2c. PI0011 Extra Power Firing Pin Spring 2d. PI0910 9mm Titanium Firing Pin 2e. PI4506.45 Extractor 2f. PI0911 9MM Firing Pin Stop 2g. PI5192 National Match 2-piece Recoil Spring Guide 2h. PI4834 Micro-Compact Outer Recoil Spring 2i. PI4831 Micro-Compact Reverse Spring Plug 3. PI4801.45 Barrel (Stainless) 3a. PI0004 Barrel Link Pin 3b. PI0003 Barrel Link 4. PI4726.45 Compact 6 Round Magazine 5. SL0005 ILS Mainspring Housing 5a. SL0008 ILS Locking Bolt 5b. PI4724 Mainspring Retainer 5c. SL0014 Mainspring (23 lb.) 5d. SL0007 ILS Mainspring Cap 5e. SL0009 ILS Plunger 5f. SL0010 ILS Plunger Spring

3 2a 2c 3a 3b 2 2b 2e 2d 2i 2h 1 1j 2f 1k 1m 1n 1p 1o 1bl 1w 1a 1br 1f 1z 1h 1g 1y 1l 1r 1q 1x 1c 1v 1d 1e 1h 1i 5d 5c 1s 1v 4 5b 1t 5a 5 55

POINT OF AIM Point of Impact Shooters may use a point of aim sight picture at 25 yards. This means that, at 25 yards the bullet should impact the target at the point visible at the top of the front sight. Shooters may also use a 6 o clock sight picture to strike the center of the target. Springfield Armory pistols are designed to use the 6 o clock sight picture at 25 yards. However, some pistols may shoot point of aim at 25 yards depending on shooter and ammunition. Point of Aim sight picture Note: 1911-A1 Ultra-Compact Pistols are designed to use standard pressure ball ammo and self-defense loads. +P ammunition is not recommended in pistols shorter than 5 inches. Use only clean, dry, original, high-quality, commercially manufactured ammunition. 56 6 O Clock sight picture

CARE & CLEANING Basic materials needed: Cleaning rod of proper size with bristle bore brushes (fiber or brass) and tip into which cleaning patch can be inserted. Cloth patches Powder solvent Lubricating oil Small lint-free cloths for wiping and oiling Bristle brush for scrubbing dirt off breech face, extractor, magazine lips, follower, etc. Use proper size bore brushes and patches - if they are too small they won t do the job, and if they are too large they will bind inside bore. When possible, insert cleaning rod from chamber end of bore and push rod all the way through so it emerges from muzzle. Do not reverse rod direction when patch or brush is in barrel, it might bind. Do not use patches dripping with solvent or oil. Wet patches or brushes, then squeeze out excess before using. When using bore brushes or a larger bristle brush on breech face, breech areas, magazines, etc., work carefully to prevent damaging components. Note: If lower parts of receiver and its mechanism are especially dirty, soak in appropriate solvent, or flush clean with same solvent. Remove grip panels before soaking or flushing, and make certain that all foreign matter is removed after cleaning. Lightly oil after cleaning. Only a very small amount of oil is needed to adequately lubricate moving parts and prevent rust. Stainless Steel pistols require slightly more lubrication than parkerized or blued pistols. Accumulation of oil tends to attract dust and dirt which interferes with the safe and reliable functioning of pistol. Do not apply excess lubricating oil. Wear eye protection when using solvent. Thoroughly wash your hands to remove powder and solvents after cleaning your gun. Always wear eye and ear protection when using any firearm. Safety and instruction manuals are available from Springfield, Inc. 57