Drilling fleet Capabilities Agriculture. Water. Environment.
Drilling fleet Overview The Gilbert & Sutherland drilling fleet includes an EDECO Model 10s mounted on a one-tonne, four-wheel drive multi-function mini loader, an EDECO T30m mounted on a 5.6 tonne crawler track base and a HE175 truck-mounted rotary head rig.
Compact Field Rig EDECO 10s (Mounted on a one-tonne, four-wheel drive multi-function mini loader) The compact design of the 10s means this powerful rig fits into tight spots like basements, buildings, car park and sites with overhead and side obstacles. Operated by a 1-2 man crew, it is ideal for concrete coring, water bore installation and niche applications. Weight Rig with auger head 960 kg Powered by a Lombardini 12LD-475-2 air-cooled diesel engine that produces 15.8 kw @ 3000 rpm Travelling speed 5kph Gradient 25% (1 : 4) Drill rig rated capacity Auger Drilling: 3 continuous flight 20 m 2.1/4 l/d Hollow Stem 12 m 3.1/4 l/d Hollow Stem 10 m Core Drilling: NW Rod Size 20 m AW Rod Size 25 m Concrete Coring: 150mm - 500mm Insurance and Crew Safety All rigs are fully-crewed and appropriately insured. All crews are qualified and overseen by a licensed driller. All crew are appropriately trained to meet WH&S obligations. Drilling operations are supported by expert environmental science, geology and engineering staff that can be called upon to address the client s site environmental risk assessment, management and compliance obligations. Rotary heads Auger Head: Coring Head: Working stroke Pull down/up 1700 Nm @ 40 rpm 190 Nm @ 0-440 rpm 1700 mm 1000 kg
Compact Field Rig EDECO 10s (Mounted on a one-tonne, four-wheel drive multi-function mini loader) Multi-function Crawler Rig EDECO T30m (Mounted on a 5.6 tonne crawler track base) Mounted Power Rig HE175 (Truck-mounted, hydraulic top drive rig) The compact design of the 10s means this powerful rig fits into tight spots like basements, buildings, car park and sites with overhead and side obstacles. Operated by a 1-2 man crew, it is ideal for concrete coring, water bore installation and niche applications. Weight Rig with auger head 960 kg Powered by a Lombardini 12LD-475-2 air-cooled diesel engine that produces 15.8 kw @ 3000 rpm Travelling speed 5kph Gradient 25% (1 : 4) Drill rig rated capacity Auger Drilling: 3 continuous flight 20 m 2.1/4 l/d Hollow Stem 12 m 3.1/4 l/d Hollow Stem 10 m Core Drilling: NW Rod Size 20 m AW Rod Size 25 m Concrete Coring: 150mm - 500mm Rotary heads Auger Head: Coring Head: Working stroke Pull down/up 1700 Nm @ 40 rpm 190 Nm @ 0-440 rpm 1700 mm 1000 kg The military-designed T30m goes where other rigs can t go. Featuring a crawler base and tilting mast, it is ideal for uneven, soft or broken ground. Operated by a 2-3 man crew, it can drill through any strata. Equipment weights Drill 5,100 kg Compressor 1,080 kg Trailer 2,000 kg approx. Powered by a Deutz F3 L1011F air-cooled diesel engine producing 29kW. @ 2500 RPM. Maximum travelling speed is 1.6 kph. Drilling performance NWY 300m Downhole 300m (6 ) HWY 240m hammer Carousel Hydraulically operated drill rod carousel Capacity 7 x 3m 2 7/8 rods Body Hydraulically powered crawler tracks Make Wirth Howden Max speed 1.6kph Rotary Head Low speed 85rpm @ 2000 Nm High speed 400 rpm @ 480 Nm Drill feed 0-6.4m/min Rotary drive 2 speed hydraulic (rapid traverse of 34m/min) capacity 7500 kg Pull out 5300 kg Down thrust 3250 kg Safe Working Load: Winch Pull - 2 fall 4000 kg Working table to pass 8-5/8 casing * Fitted with pipe boom for service winch allowing equipment to be brought to the drilling position through 180 deg Designed for military use, the HE175 is mounted on an Iveco Eurotrakker 6x6 RHD truck for rapid field deployment. Operated by a 3-4 man crew and jacked-up by four hydraulic stabliser legs, this powerful rig can drill through any strata to depths of up to 500m (rotary 300mm dia). Dimensions with running gear Length 4851 mm Width 2261 mm Height 2591 mm Track width 1778 mm Weight 6169 kg Rated capacity (No drill collars) Rotary drilling: Down the hole: 300 mm dia 500 m 300 mm dia 200 m 500 mm dia 200 m 500 mm dia 100 m Power pack Caterpillar 3306B DITA water-cooled diesel engine producing 224 Kw @ 1800 RPM Rotary head output Max torque Max speed Max torque (reverse) Spindle bore 8000 Nm @ 0-75 RPM 4000 Nm @ 0-150 RPM 16000 Nm @ 0-30 RPM 75 mm * Total working length 6.5 m below sheave block hook Maximum drill pipe 6.0m Rotary head stroke 4.4 m Hoist capacity (pull back) 170 Kn Feed capacity (pull down) 90 Kn Fast hoist speed 22 m/min Slow hoist speed 2.8 m/min Down feed (drilling) 0-2 m/min Gross crown block capacity 160 Kn
Drilling fleet Pricing Rigs are available on day rates or by the metre, plus costs (e.g. mobilisation, site induction, obtaining permits etc). Stand-by rates apply. Quotes and terms are available upon request. For more information please call 07 5578 9944 or email drilling@access.gs www.access.gs