FREE ONLINE GPS TRACKING SERVICE

XT008 USER MANUAL FREE GPS TRACKING BY CORVUSGPS.COM FREE ONLINE GPS TRACKING SERVICE THE DO IT YOURSELF TRACKING SYSTEM. CLICK HERE TO REGISTER YOUR ACCOUNT NOW! WWW.CORVUSGPS.COM

SERVER IP ADDRESS: 89.134.146.57 SERVER PORT NUMBER: 31201 QUICK SETUP GUIDE XT008 ( or other models look the same ) IMPORTANT NOTES! Place the SIM card to a cellphone and please check these few things: SIM card has not run out of credit SIM PIN code request is disabled Caller ID display is turned on After you make sure the steps above are successfully completed, insert the SIM card to your GPS tracker and check the next page.

SERVER IP ADDRESS: 89.134.146.57 SERVER PORT NUMBER: 31201 CONFIGURATION WITH SMS OR DATA CABLE 1.) CONFIGURE WITH SMS COMMANDS: Turn ON your GPS tracker and follow these steps carefuly. Send all SMS commands to the tracker correctly: No. Command Info 1st begin123456 resets all settings to factory default 2nd apn123456 xyz sets the required APN for GPRS configuration 1 3rd apnuser123456 xyz sets the USER NAME for GPRS configuration (optional) 1,2 4th apnpasswd123456 xyz sets the PASSWORD for GPRS configuration (optional) 1,2 5th adminip123456 89.134.146.57 31201 sets our server's IP address and Port number 6th t030s***n123456 sets the report time interval to 30 seconds 3 1 The "xyz" depends on your mobile phone company, for more information ask your SIM supplier or check their website! 2 Do not send this messages if you don t need USER NAME and PASSWORD for the GPRS connection! 3 The report interval must NOT be less than 30s 4 123456 is the default password, if you changed you need to use your chosen one 5 Do not forget to use "spaces" in the commands! --------------------------------------------------------------------- OR --------------------------------------------------------------------- 2.) CONFIGURE WITH PC AND USB DATA CABLE: Connect the tracker: 1.) Install the Prolific USB Driver downloaded from our website 2.) Connect the serial cable to the PC 3.) Open the Windows Device Manager 4.) Check the COM port number at Ports (COM & LTP) 5.) Run the Access Port software downloaded from our website 6.) Setup the right COM port number at Tools / Configuration menu and click OK 7.) Connect the serial cable s longer lead to the GPS tracker 8.) Power ON the GPS tracker with the ON/OFF button 9.) When you see the "AT+CREG?" text in the "AccessPort" software enter the commands below: Click to "Send" button after each command! No. Command Info 1st begin123456 resets all settings to factory default 2nd apn123456 xyz sets the required APN for GPRS configuration 1 3rd apnuser123456 xyz sets the USER NAME for GPRS configuration (optional) 1,2 4th apnpasswd123456 xyz sets the PASSWORD for GPRS configuration (optional) 1,2 5th adminip123456 89.134.146.57 31201 sets our server's IP address and Port number 6th t030s***n123456 sets the report time interval to 30 seconds 3 7th save123456 save all settings 1 The "xyz" depends on your mobile phone company, for more information ask your SIM supplier or check their website! 2 Do not send this messages if you don t need USER NAME and PASSWORD for the GPRS connection! 3 The report interval must NOT be less than 30s 4 123456 is the default password, if you changed you need to use your chosen one 5 Do not forget to use "spaces" in the commands! Disconnect the tracker: 10.) Click on the "Serial Port Switch" button if you finished the setup 11.) Remove the serial cable from the GPS device 12.) After you removed, the tracker starts to send data to our server automatically 13.) Remove the serial cable from the PC

LIST OF ALL COMMANDS (Some of these commands are not supported by XT008.) FUNCTION COMMANDS EXAMPLE Password modification password+old password+space+new password password123456 666888 P.S:the password should be 6 digitals Authorization admin+password+space+cellphone number admin123456 13311112222 P.S:there are 4 other numbers can set as the masters,use the same way to set them. IP and Port Setting adminip+password+space+ip address+space+port adminip123456 192.167.1.1 8899 P.S:When you need the tracker has the way of GPRS transferring,this is the necessary setting. APN setting APN+password+space+the user's APN APN123456 internet P.S:When you need the tracker has the way of GPRS transferring,this is the necessary setting.and APN refers to the GSM card's APN. APN user name setting Apnuser+password+space+apn's username apnuser123456 come P.S:If the APN has user name,this is the command to setting this. APN password setting Apnpasswd+password+space+apn's password apnpasswd123456 cmet P.S:If the APN has password,this is the command to setting this. Interval tracking t030s005n+password t030s005n123456 P.S:T=time,s=second,m=minutes,h=hour,n=times,t030s005n123456 means track 5 times for 30s interval, "***" means countless times.and the minimum interval time is 5 seconds(new vesion tracker),30 seconds(old vesion),the maximum times is 250 times. Tracking mode tracker+password tracker123456 P.S:If you need switch the other modes to tracking mode,you need send this commands. Track once tracking one / or call the tracker once tracking one P.S:If you want to have the tracker only report once,send tracking one to the tracker,or call the tracker once. Listen in mode monitor+password monitor123456 P.S:If you need switch the other modes to listen in,you need send this commands. When you use the tracker first time,call the tracker,tracker reports you the coordinates,send monitor123456,call the tracker you will hear what happen around the tracker. Geofence stockade+password+space+longitude, latitude;longitude,latitude stockade123456 22.567185,114.051248;22.555666,114.777888 P.S:Send this sms command to the tracker,then if the tracker run out the area you have set,it will send "stockade"with the location to you. Movement Alert move+password move123456 P.S:The tracker will move 500m at least,or you cannot get this alert."move with the location" Overspeed Alert speed+password+space+080 speed123456 080 P.S:The unit of the speed is km which is the orignal data from the GPS,and if the speed less then 30km/h,you won't get the alert "speed+location" Low battery Alert no needing to set up No needing to set up P.S:When the back up battery is less than 3.7V,it will send " L". Initialization begin+password begin123456 P.S"To cancel all the settings,you need this commands,but if you forget the password,you need update the firmare. IMEI Checking imei+password imei123456 P.S:If you want to know the IMEI number of the tracker,you need this command. SOS no needing to set up No need to set up P.S:When someone press the SOS,you will get the information of 'help me with the coordinates". Ignition alert fortify+password fortify123456 P.S:Only for the vehicle tracker,there are two wires connect the ACC(ignition),if you send "fortify123456",then anyone switch on the vehicle,it will send alert. Ignition Status checking fortified+password fortified123456 P.S:If you want to make sure that the tracker in under this function,send this commands,and tracker will reply you. Main power losing alert no needing to set up No need to set up P.S:If the main power is losing,the tracker will send "battery". Time zone setting Time zone+password+space+gmt time Time zone123456 2 P.S:"UK time is time zone123456 1"currently. Individual Website setting Home+pasword+space+the user's webite home123456 www.tracker.com P.S:If "tracker" wants make the returned sms has their domain name,they can set "home123456 www.tracker.com". Relay on/off (stop engine) Powercar+password+space+1 (or 0) Powercar123456 1 P.S:Only the vehicle tracker has this function,"powercar123456 1/0" 1=on,0=off Shake Alert(with the motion shake+password+space 1-10 shake1234656 1 sensor) P.S:Only the new version tracker has this function,from 0-10,means from shake heavily to softly,1 means the heaviest,10 means the softest.0=off Read SD card Readsd+password+space+1 readsd123456 1 P.S:Only the new version tracker has this function,where there is not GPRS connection,tracker records the information into the SD card and when there comes the GPRS connection,tracker sends all the information to the server.1=on,0=off. SMS report smslinkone+password smslinkone123456 Send report in SMS (it s working during the gprs communication too ) Restart tracker restart+password restart123456 P.S:This command is restart the tracker.

GPS VEHICLE TRACKER USER MANUAL-XT008 UPreface Thank you for purchasing GPS Vehicle Tracker. This manual shows how to operate the device smoothly and correctly. Make sure to read this manual carefully before using this product. Please note that specification and information are subject to changes without prior notice in this manual. Any change will be integrated in the latest release. The manufacturer assumes no responsibility for any errors or omissions in this document. 1

Content 1 Summary ---------------------------------------------------------------------------------- 3 2 Application --------------------------------------------------------------------------------- 3 3 Hardware description 3.1 Wires connection ---------------------------------------------------------------------------- 3 3.2 Interior -------------------------------------------------------------------------------------------- 3.3 Relays connection ------------------------------------------------------------------------------- 5 5 4 Specifications ---------------------------------------------------------------------------------------- 6 5 Battery and SIM card installation ------------------------------------------------------------------ 6 6 Startup ------------------------------------------------------------------------------------- ----------- 7 7 Usage --------------------------------------------------------------------------------------------------- -- 7 8 Fortifying mode --------------------------------------------------------------------------------- --------- 8 8.1 Engine started alert ---------------------------------------------- --------- -------- 8 8.2 Movement alert --------------------------------------------------------- --------- -------- 8 8.3 Power cutoff alert --------------------------------------------------------- --------- -------- 8 8.4 ENGINE-OFF Remotely function ---------------------------------------------- --------- -------- 8 8.5 Increase relays function --------------------------------------------------- --------- -------- 8 8.6 More function with using the relays ----------------------------------------- --------- ------- 9 8.7 Checking the working status ---------------------------------- --------- -------- 9 9 Tracking mode -------------------------- --------- -------- ------- 9 9.1 Initialization ---------------------------------- --------- ------- 9 9.2 Change the Password ---------------------------------- --------- ------- 10 9.3 Authorization ---------------------------------- --------- ------ 10 9.4 Auto Track ---------------------------------- --------- ------11 9.5 Geo-fence ---------------------------------- --------- ------- 12 9.6. Tlimit Function ---------------------------------- --------- ------- 12 9.7 Movement alert ---------------------------------- --------- -------- 13 9.8 Overspeed alert ---------------------------------- --------- -------- 14 9.9 IMEI checking ------------------------------ --------- -------- 15 9.10 Time zone setting ----------------------------------------------------------------- 15 9.11 SOS --------------------------------- --------- -------- 15 9.12 SMS LINK --------------------------------- --------- --------------------------------------16 8.13 SMS ONE ----------------------------------------------------------------------------16 2

9.14 Low battery alert --------------------------- --------- ------- 16 9.15 SMS center ------------------------------ --------- -------- 16 9.16 GSM ID --------------------------- --------- ------- 16 9.17 Motion Sensor ---------------------------- --------- -------- 17 9.18 SD Card function ------------------------------ --------- -------- 17 9.19 SIM conversion from A to B ------------------------------ --------- -------- 17 10 Monitoring and Talking Mode ------------------------------ --------- -------- 17 11 GPRS setting ------------------------------------------------------------------- 18 12 MMS picture function ------------------------------------------ 19 13 RFID function --------------------------------------------------------------------- 19 14 Cautions --------------------------------------------------------------------- 19 15 Faults & Solutions --------------------------------------------------------------------- 19 16 Cable connection diagram --------------------------------------------------------------- 19 1 Summary Working based on existing GSM/GPRS network and GPS satellites, this product can locate and monitor any remote targets by SMS or GPRS,and guard against theft of Vehicle. 2 Applications Rental vehicle / Fleet management etc Covert Tracking 3 Hardware Description 3.1 Wires Connection 3

SIM B Card slot Connect GSM antenna For upgrade the firmware Connect GPS antenna DC +9-36V Working status indicator 2 4 6 8 10 12 14 16 18 20 E F G H 1 3 5 7 9 11 13 15 17 19 A B C D GPS indicator GND 1 SP Connects the round speaker (connection is ready,only need connect the speaker) 2.SP + Connects the round speaker (connection is ready,only need connect the speaker) 3. MIC + microphone +(connection is ready) 4. MIC + microphone -(connection is ready) 5. GND SOS GND (connection is ready) 6. SOS SOS +(connection is ready) 7. Oil test (analog input port )connects the black wire for the fuel sensor. Note: Please use our fuel sensor only. 8. ACC (digital input port) connect the ACC (ignition) 9. V + connects relay, connction is ready,conencts the relay,it works. 10. Output (digital output) Connects the extra relays 11. Temperature test (analog input port) connects the middle connector of the round temperature sensor. 12. Cut oil (digital output) connects the relay, connction is reay,conencts it,it works. 13. Out A (digital output) for the extra relay. 4

14. Out B (digital output) 接 RFID 的 声 音 控 制 线 15. IO6 in (digital input port) connects the detective circuit of the switches for the doors and tail in the car. 16. IO5 in(digital input port) connects the detective circuit of the switches for the doors and tail in the car. 17. IO4 in (digital input port) connects the detective circuit of the switches for the doors and tail in the car. 18. IO3 in (digital input port) connects the detective circuit of the switches for the doors and tail in the car 19. IO2 in (digital input port) connects the detective circuit of the switches for the doors and tail in the ca 20. IO1 in (digital input port) connects the detective circuit of the switches for the doors and tail in the ca Note: Two UART with the connectors of A.B C D; E F G H for 2 purposes. A. Connect the extra camera B. For input/output the data Connects any conenctors ABCD or EFGH optionally, function actived. UART1 (A.GND B.RX C. TX D.+5V) UART 2 (E.GND F.RX G.TX H.+5V) 3.2 Interior Put SIM card here A(back of Mainboard) Put SD card here 3.3 Relays connection Conencts the tracker 5

Relays Connect oil routes Connect oil routes 4 Specs Content Dimension. Weight Network Band GPS chip GPS sensitivity GPS accuracy Time To First Fix Power Battery Standby Storage Temp. Operation Temp. Humidity Specs. 8.2x8.2x2.8cm 195g GSM/GPRS GSM850/ 900/1800/1900Mhz SIRF3 chip -159dBm 5m Reacquisition 0.1s Cold status 45s Warm status 35s Hot status 1s 9 36V input Chargeable changeable 3.7V 1100mAh Li-ion battery 50hous -40 C to +85 C -20 C to +55 C 5%--95% non-condensing 5 Battery and SIM card installation Make sure that there is no call transfer and call display is on, and PIN code off. The SMS message must in Text format, can t be identified for PDU format. Steps: 1.Open the rear cover, insert a SIM card to the simcard slot A. (If using one simcard,do not insert it into simcard slot A since the default simcard is simcard B) 2.Insert the SD card 3.Use a stick to pick up the simcard slot B,insert the simcard. SIM card A 6 Use a stick to pick up the

Install SD card Insert the simard slot with the sim card Put the SIM card into the slot with the right direction. 6 Startup Put the SIM card and SD card in right places.(put the B card slot in place,the indicator light will blink quickly after 10 seconds, remove card slot B, tracker stops working) Connect the power supply of the car (The red indicator inside the tracker is on when conencting the 9-36 V power supply) It takes 40-60 seconds to get the GPS and GSM signals and begins to work.the red indicator blinks every 1 second,the blue GPS indicator blinks every 3 seconds. Everything is ready when the blue GPS indicator blinks normally, then you can do the following Settings. 7 使 用 本 产 品 有 四 种 工 作 模 式, 设 防, 跟 踪, 通 话 及 监 听, 并 且 四 种 模 式 可 以 互 相 切 换 当 开 机 后, 默 认 状 态 为 跟 踪 模 式, 你 可 以 发 送 短 信 fortify+password 转 移 到 设 防 模 式, 7

发 送 monitor+password 转 移 到 监 听 模 式, 发 送 talk+password 转 到 通 话 模 式, 发 送 tracker+password 转 回 跟 踪 模 式 7 Usage The tracker has three working modes: Fortifying mode, Tracking mode and Monitoring mode. Working modes can be changed reciprocally. The default mode is Fortifying mode,sends command tracker+password,gets tracking mode,sends minitor+passwords,get monitoring mode,sends fortify+password,goes back fortifying mode 8 Fortifying Mode Under the fortifying mode, call the tacker to arm or disarm the fortify function.when the forify mdoe is armed,the indicator blinks every 4 seconds and if blinks every 1 second,means the fortify is disarmed.(there is no cooridnates goes back for call when tracker works in fortifying mode) When the fortify is armed,the alerts will be as below: 8.1 Engine Started illegally Alert In fortifying mode, the tracker will start the ACC examine automatically. It will warn up the user when the engine is started. Alert SMS format: lat: 22.567908N long: 114.051395E speed: 0.00 05/01/11 04:47 F:3.87V,0, Signal:F fortify imei:354776036842240 05 130.8 460 01 9523 29062, Oil=100%,T=40,RFID=3333333 8.2 Movement Alert This function is using for the owner to get an alert when the tracker moves out of a restricted district (500m radius), Response SMS format: lat: lat: 22.567908N long: 114.051395E speed: 0.00 05/01/11 04:47 F:3.87V,0, Signal:F moved imei:354776036842240 05 130.8 460 01 9523 29062, Oil=100%,T=40,RFID=3333333 8.3 Power Cutoff Alert In this mode, the tracker will warn up the user automatically when the main power is cut off unwontedly,such as if someone cut the wire connected the car with the device, it will alert Battery with coordinates. Alert SMS format: lat: lat: 22.567908N long: 114.051395E speed: 0.00 05/01/11 04:47 F:3.87V,0, Signal:F battery imei:354776036842240 05 130.8 460 01 9523 29062, Oil=100%,T=40,RFID=3333333 8

8.4 ENGINE-OFF Remotely function ( Remark::You can send the below sms after the relay and the related wires conencted) 8.4.1 Send powercar123456 11, tracker disconnects the oil and electricity and cut the engine,car stops slowly and you will get SMS powercar ok. 8.4.2 Send powercar123456 00,tracker connects the oil and electricity,the engine will be restore,you will get SMS powercar ok. 8.5 More function with using the relays Please send the below commands to control the extra relays. relaya123456 0 control the OC output of wire A, 0 is the output low Voltage level,1 is the output high voltage level. relayb123456 0 control the OC output of wire B, 0 is the output low Voltage level,1 is the output high voltage level. Output123456 101 control the OC output of the output wire, 0 is the output low Voltage level,1 is the output high voltage level.(101 is the variety of the voltage of the relay,high-low-high,the interval is 1 second, it can be 010 also,means low-high-low, the inteval is 1 second as well, can be used for car door open 8.6 External input detection function Thre are 6 detective wires,if you need external input data or signals(such as the information of the door and tail of the car) 15. IO6 in (digital input port) connects the detective circuit of the switches for the doors and tail in the car.) 16.IO5 in (digital input port) connects the detective circuit of the switches for the doors and tail in the car) 17.IO4 in (digital input port) connects the detective circuit of the switches for the doors and tail in the car) 18.IO3 in (digital input port) connects the detective circuit of the switches for the doors and tail in the car) 19.IO2 in (digital input port) connects the detective circuit of the switches for the doors and tail in the car) 20.IO1 in (digital input port) connects the detective circuit of the switches for the doors and tail in the car) SMS string is : lat: 22.567908N long: 114.051395E speed: 0.00 05/01/11 04:47 F:3.87V,0, Signal:F Trigger6Start imei:354776036842240 05 130.8 460 01 9523 29062, Oil=100%,T=40,RFID=3333333 SMS alert string is: lat: 22.567908N long: 114.051395E speed: 0.00 05/01/11 04:47 F:3.87V,0, Signal:F Trigger6Stop imei:354776036842240 05 130.8 460 01 9523 29062, Oil=100%,T=40,RFID=3333333 Remark::Trigger6Stop is low voltage level, Trigger6Start is high voltage level, 6 is item no. of IO IN, informs you the origin of the alert. 8.7 Checking the working status ( fortify or no fortify ) You can send SMS command fortified123456 to tracker, it will report fortifying or no fortify to you. 9

Out of Fortifying mode SMS format: lat: 22.567908N long: 114.051395E speed: 0.00 05/01/11 04:47 F:3.87V,0, Signal:F no fortify imei:354776036842240 05 130.8 460 01 9523 29062, Oil=100%,T=40,RFID=3333333 Fortifying mode SMS format: lat: 22.567908N long: 114.051395E speed: 0.00 05/01/11 04:47 F:3.87V,0, Signal:F fortify imei:354776036842240 05 130.8 460 01 9523 29062, Oil=100%,T=40,RFID=3333333 9 Tracking Mode 9.1 Initialization Send SMS begin+password to the unit, it will reply begin ok and initialize all the settings. (default password: 123456) TO:13188888888 begin123456 From:13188888888 begin ok 9.2 Change the Password Send SMS password+old password+space+new password to change the password. (default password: 123456) TO:13188888888 password123456 888999 From:13188888888 password ok 9.3 Authorization 9.3.1 Send SMS admin+ password+ space+ cell phone number to set the first authorized number, the other authorized numbers should be set by the first authorized number. 10

9.3.2 Send SMS noadmin+password+space+authorized number to cancel the authorized number. 9.3.3 When an authorized number sends SMS or dials up the unit, it will reply a SMS as below: Lat: 22.566901 long: 114.051258 speed: 0.00 14/08/09 06.54 F:3.85V,1,Signal:F imei:354776031555474 05 43.5 460 01 2533 720B, Oil=80%,T=40,RFID=3333333 Lat: 22.566901 long: 114.051258== Coordinate 0.00 === speed 14/08/09 06.54== Date&Time F:3.85V == battery power 1 == charging 0 means no charging Signal:F ==== Full GPS signal 0 means weak GPS signal 354776031555474== IMEI 05=number of satellites ( from 3 to 10) 43.5=Altitude 460 = MCC Mobile Country Code 01 == MNC Mobile Network Code 2533= LAC Location area code 720B= Cell ID Oil=80% 油 量 值 T=40 温 度 值 RFID=3333333 当 前 用 的 RFID 卡 号 9.4 Auto-Track This function is using for the user to receive SMS with Geo-info in a certain time. 9.4.1 Set up: Send SMS t030s005n+password to the unit, it will report the Geo-info at 30s intervals 11

for 5 times.it will reply as t030s005n OK 9.4.2 Send SMS t030s***n+password to the unit, it will reply SMS heaps of times. You will receive a reply as t030s***n OK 9.4.3 Send notn+password to delete the auto track. TO:13188888888 Notn123456 From:13188888888 Notn ok 9.5 Tlimit Function 9.5.1 Send tlimit123456 50 (50 is the restricted distance in meter, minimum is 1m, maximum is 6000m), tracker replies tlimit ok (note: this command should work along with auto tracking command) Once this function is set up, the tracker will only send coordinates if the moving distance is not less than the restricted value in each interval, otherwise, it will not send new coordinates. 9.5.2 Send tlimit123456 0 is to cancel this function, tracker replies tlimit ok. 9.6 Geo-fence Set up a geo-fence for the unit to restrict its movement within a district. The unit will send message to the authorized numbers when it moves out of the district. Notes: This function will be invalid if the unit moves outside the district. You need to re-set it if you want this function again. 12

9.6.1 Send SMS stockade+password+space+longitude,latitude; longitude,latitude to the unit to set the restricted district. Remark:The first latitude&longitude is coordinate of the top left corner of the Geo-fence, while the second latitude&longitude is the coordinate of the bottom right corner. TO:13188888888 stockade123456 From:13188888888 stockade ok 114.124845e,22.56718 5n;114.777888e,22.55 5666n 9.6.2 Send SMS nostockade+password to deactivate this function. TO:13188888888 nostockade123456 From:13188888888 nostockade ok This function will be invalid if the unit moves outside the district Response SMS format: stockade!+geo-info. It will alarm one time in each setting. From:13188888888 lat: 22.566923 long: 114.051331 speed: 0.00 28/11/10 03:33 F:4.32V,0, Signal:F stockade imei:359587011016261 05 41.5 460 01 2533 720B Oil=80%,T=40,RFID=3333333 9.7 Movement Alert 13

This function is using for the owner to get alarm when the tracker moves out of a restricted district. 9.7.1 Set up: Send SMS move+password to the unit to set the movement alert. then the unit will reply move ok! if the setting is successfully. TO:13188888888 move123456 From:13188888888 move ok 9.7.2 Cancel:Send SMS nomove+password to deactivate this function This function will be out of effect after the unit moves outside the district. TO:13188888888 nomove123456 From:13188888888 nomove ok This function will be invalid if the unit moves outside the district Response SMS format: move!+geo-info. It will alarm one time in each setting. From:13188888888 lat: 22.566923 long: 114.051331 speed: 0.00 28/11/10 03:33 F:4.32V,0, Signal:F move imei:359587011016261 05 41.5 460 01 2533 720B Oil=80%,T=40,RFID=3333333 14

9.8 Overspeed Alert: This function is using for the owner to control the target s speed. 9.8.1 Set up: Send SMS speed+password+space+080 to the unit,such as speed123456 080 TO:13188888888 speed123456 080 From:13188888888 speed ok 9.8.2 Cancel: Send SMS nospeed+password to the unit. TO:13188888888 nospeed123456 From:13188888888 nospeed ok Response SMS format: speed+080!+geo-info (suppose the speed is 80km/h). The tracker will check the speed in 1 minute interval and alarm if it is overspeed. 9.9 IMEI Checking: From:13188888888 lat: 22.566923 long: 114.051331 speed: 0.00 28/11/10 03:33 F:4.32V,0, Signal:F speed imei:359587011016261 05 41.5 460 01 2533 720B Oil=80%,T=40,RFID=3333333 Send SMS imei+password to the unit to check the IMEI number of the unit. TO:13188888888 Imei123456 15 From:13188888888 imei35000112222222

9.10 Time Zone setting Send time zone+password + GMT time,reply time zone ok. (note: if GMT time is positive, just write the number. If time zone is negative, have to write 1) TO:13188888888 Time zone23456 1 TO:13188888888 Time zone23456-1 From:13188888888 time zone ok 9.11 SOS Button Press the SOS for 3 seconds, it will send help me!+ Geo-info to all the authorized numbers in 3 minutes. Alarm SMS format:: lat: 22.567908N long: 114.051395E speed: 0.00 05/01/11 04:47 F:3.87V,0, Signal:F help me imei:354776036842240 05 130.8 460 01 9523 29062, Oil=80%,T=40,RFID=3333333 9.12 SMS LINK 9.12.1 Send smslinkone+password, The tracker will reply a GOOGLE map link to admin number.the position can be checked directly on smartphone(with GPRS enabled) Format:http://maps.google.com/maps?f=q&hl=en&q=22.567610,114.051227&speed: 0.00 12/11/10 14:36 F:4.22V Signal:F imei:012207000691839 9.12.2 Send smslink123456, it will reply smslink OK. The tracker will send the following SMS format always. http://maps.google.com/maps?f=q&hl=en&q=22.567610,114.051227&speed: 0.00 12/11/10 14:36 F:4.22V Signal:F imei:012207000691839 9.12.3 Send smstext123456, it will reply smstext OK. The tracker will send normal SMS 16

9.13 SMS ONE Send smsone+password.the tracker will reply coordinates by SMS to admin number or by GPRS to server 9.14 Low Battery Alert When the backup battery is less than 3.7 V, it will send low battery alert to admin number 9.15 SMS Center ( or appointed number) 9.15.1 Setup: Send SMS adminsms+password+space+cell phone number to setup the SMS center. The tracker will reply Geo-info & authorized number to sms center number even if the admin numbers call or send command to the tracker 9.15.2 Cancel: Send SMS noadminsms+password to cancel the SMS center. Response SMS format: authorized number+geo-info 9.16 GSM ID(this function can be add or delect for customization.) GSM ID are in each sms or gprs data. The tracker can be found by GSM ID without gps signal. But the customers have to ask their GSM operator for data base of the GSM ID. 9.17 Motion Sensor This function is used to protect the vehicel or tracker when it is touched. 9.17.1 Setup: Send shake+password+space+1-10 to the tracker to set up this function.(1-10 means the level of intensity) 9.17.2 Send SMS shake+password+space+1, 1 is the least sensitivity. Have to shake the tracker strongly to get the alert. 9.17.3 Send SMS shake+password+space+10, 10 is the most sensitivity. Have to shake the tracker slightly to get the alert 9.17.4 Cancel: Send SMS shake+password+space+0 to remove this function. 9.18 SD card function A mini SD card can be put in the tracker s SD card slot. The GPRS data can be saved in the SD card if GPRS is disconnected. It will send data to the GPRS server again if GPRS is connected again. 9.18.1 Setup: Send SMS sdlog+password+space+1 to activate the sd card-saving function 17

Cancel: Send SMS sdlog+password+space+0 to the tracker to deactivate this function 9.18.2 Setup: Send SMS readsd+password+space+1 to ask the tracker to send data in the SD card to the GPRS server. Cancel: Send SMS readsd+password+space+0 to ask the tracker to stop sending data in the SD card to the server. 9.19 SIM conversion from A to B 9.19.1 If you are using simcard B,sends a command selectsim123456 A,after 1 minute,simcard A works,and Simcard B stops working.the same thing for after sending selectsim123456 B 9.19.2 When 2 simcards are working simultaneously.simcard A loses the GSM signal,simcard B will work automatically,the same thing for Simcard B. 9.19.3 Send selectsim123456 A, A card works permanently, send selectsim123456 B,B card works permanently, send selectsim123456,will transform automatically between A card and B card 10 Monitor and Talking Mode 10.1 Send SMS monitor+password, the response from the tracker is monitor ok then you can hear the voice around the tracker after your call. 10.2 Send SMS talk+password,it will reply talk ok, if connects the round speaker,you can have 2 ways communication. (Remark: Send volume+password+60 to adjust the volume,60 is variable, the grades from 0-99,from low to high level,send volume123456 0 for listen in only.) 11 GPRS setting APN(access point name), IP, PORT have to be set up for gprs function. Apn user, apn password have to be set up also if there are. So please contact with the gsm operator for them 11.1 Set GPRS protocols 11.1.1 Set TCP protocols:send SMS Gprsmode+password+space+0 to set up TCP protocol, tracker will reply GPRSMODE ok (note: TCP is the default mode in the firmware) 11.1.2 Set UDP protocols: Gprsmode+password+space+1 to set up UDP protocol, tracker will reply GPRSMODE ok 11.2 Set IP address and port: 18

Setup: adminip+password+space+ip address+space+port. If setup successfully, the tracker will reply SMS adminip ok Cancel: Send SMS noadminip+123456 11.3 Set APN Setup: Send SMS APN+password+space+B card APN content+ space +A card APN content. If setup successful, the tracker will reply SMS APN ok. (Remark:if use B card only, then no need to set A card APN content) Cancel: The old APN will be invalid automatically when a new APN is set. 11.4 Set APN USER Setup: Send APNUSER+password+space+B card APN user content+ space +A card APN user content, the tracker will reply SMS APNUSER OK. (Remark:if use B card only, then no need to set A card APN user content) Cancel: The old APN user name will be invalid automatically when a new APN user name is set. 11.5 Set APN s Password Setup: Send APNPASSWD+password+space+B card APN password content+ space +A card APN password content, the tracker will reply SMS APNPASSWD OK. (Remark:if use B card only, then no need to set A card APN password content) Cancel: The old APN password will be invalid automatically when a new APN password is set. 11.6 GPRS setting The tracker will hang up the calling in gprs mode when an authorized number calls to the tracker, then send gprs data to the server. GPRS Format: serial number, the authorized number, GPRMC data, GPS signal( F is strong L is weak), alarm information, imei, satellite number,altitude, battery power (F is full,l is weak), charging state( 1 charging,0 no charging), byte number, checksum, MCC, MNC,LAC, CELL ID Oil=80% 油 量 值 T=40 温 度 值 RFID=3333333 RTID 卡 号 码 For example: 100312033421,13145826175,GPRMC,033421.851,A,2234.0209,N,11403.0733,E,1.87,347.73,12031 0,,,A*62,F,help me, imei:354776036842240,03,73.5,f:4.14v,0,138,46772,460,01,2533,720b Oil=80%,T=40,RFID=3333333 12.MMS 拍 照 功 能 设 置 12.1 将 摄 像 头 插 入 定 位 器 的 上 排 插 座 内.( 注 : 使 用 拍 照 功 能 定 位 器 内 一 定 要 放 一 张 1G 的 SD 卡 ) 12.2 在 定 位 器 里 设 置 好 授 权 号 码, 设 授 权 步 骤 同 上 9.3.( 注 : 授 权 号 码 的 手 机 要 有 彩 信 功 能.) 19

12.3 设 置 定 位 器 SIM 卡 的 彩 信 设 置 : 格 式 如 :MMSSET123456 cmwap 10.0.0.172 80 mmsc.monternet.com ( 注 :CMWAP 是 APN 10.0.0.172 80 是 IP 和 端 口 mmsc.monternet.com 是 CENTER) 12.4 自 动 拍 照 设 置 指 令 : mms123456 120 5 ( 注 :120 为 间 隔 时 间, 最 小 为 60, 单 位 是 秒,5 是 拍 摄 发 送 张 数, 如 拍 摄 无 数 张 999) 12 MMS Photograph function setting 12.1 Connect the camera with the tracker (note: must insert a 1GB SD card to the tracker when using the MMS photograph function) 12.2 Set authorization number for the tracker (note: authorization number phone should have MMS function.) 12.3 Set the APN, APN user, APN password for the tracker 12.4 Format: MMSSET+password + Spaces + APN + Spaces + USER + Spaces + PASSWORD 12.5 Auto photographing: mms123456 120 5 (note: 120 means 120 seconds interval, minimum is 60 seconds, 5 means the number of picture) 13.RFID 功 能 13.1 RFID 读 卡 器 的 接 线 13.1.1 将 RFID 线 的 插 头 插 入 定 位 器 的 下 排 插 座 内, 插 座 上 的 一 根 棕 线 头 接 到 定 位 器 的 棕 线 头 接 到 紫 线 输 出 线 紫 线 上, 接 错 没 刷 卡 音 如 图 : 13.1.2 线 和 插 头 接 对 确 后,RFID 读 卡 器 的 红 灯 会 亮, 此 时 就 可 刷 卡 了 13.2 RFID 读 卡 器 使 用 13.2.1 RFID 读 卡 器 读 卡 将 RFID 卡 放 到 读 卡 器 上, 读 卡 器 会 发 出 一 声 长 响 音, 说 明 此 卡 号 被 读 成 功, 这 时 有 定 位 任 务 在 定 位 信 息 里 就 有 RFID= 此 卡 号, 如 开 机 没 读 到 卡 时 RFID= 空. 20

13.2.2 RFID 卡 授 权 : 发 短 信 : rfidadd123456 11A156789 回 复 : rfidadd OK 格 式 : rfidadd+ 密 码 + 空 格 + 卡 号 ( 可 授 权 卡 号 10 个 ) 注 : 授 权 卡 刷 卡 时 是 一 声 长 响, 表 示 刷 卡 成 功. 非 授 权 号 刷 卡 是 三 声 短 响, 表 示 不 成 功. 并 有 一 条 报 警 信 发 出. lat: 22.567908N long: 114.051395E speed: 0.00 05/01/11 04:47 F:3.87V,0, Signal:F NoSec imei:354776036842240 05 130.8 460 01 9523 29062,Oil=80%,T=40,RFID=3333333 13.2.3 RFID 卡 删 除 授 权 : 发 短 信 : rfiddel123456 11A156789 回 复 : rfiddel OK 格 式 : rfiddel + 密 码 + 空 格 + 卡 号 13.2.4 RFID 卡 授 权 查 询 发 短 信 : rfidlist123456 格 式 : rfidlist + 密 码 回 复 : 11A156789 22356C88 回 复 当 前 已 授 权 的 卡 号 13.2.5 RFID 功 能 开 关 发 短 信 : rfid123456 1/0 (1 是 打 开 功 能,0 是 关 闭 功 能 ) 回 复 : rfid OK 格 式 : rfid + 密 码 + 空 格 +1 或 0 ( 注 : 此 功 能 打 开 后 继 电 器 是 断 开 状 态, 这 时 只 有 刷 一 下 RFID 卡 继 电 器 才 会 接 通, 此 时 连 通 ACC 后 再 关 ACC 继 电 器 又 会 断 开, 如 要 接 通 继 电 器 时 又 要 刷 一 下 RFID 卡, 反 复 此 动 作 做 方 便 车 队 管 理.) 13.2.6 RFID 开 关 功 能 查 询 发 短 信 : rfidsec123456 回 复 : rfid on/off 格 式 : rfidsec + 密 码 14 Cautions Please comply with the instructions to extend the unit life: 1. Keep the unit dry. Any liquid, i.e. rain, moisture, may destroy or damage the inside circuitry. 2. Don t use & store the unit in dusty places. 3. Don t put the unit in overheated or overcooled places. 4. Handle carefully. Don t vibrate or shake it violently. 5. Clear the unit with a piece of dry cloth. Don t clean in chemicals, detergent. 6. Don t paint the unit, this may cause some foreign materials left in between the parts. 7. Don t disassemble or refit the unit. 21

8. Please use the battery and charger provided by manufacturer. Using other batteries and chargers will cause unwanted situation. 9. Don t dismount the antenna randomly, or use other antennas. This may interfere the transmission, and increase the radiation as well. 15 Faults & Solutions Startup Fail Faults Hangup Fail Monitor Fail Location report in digits of zeros. Solution Check the SIM and see if it is fully charged or correctly installed. Check if the unit received GPS signal or not,or if the SIM card there is calling display or not. Check if the authorized number is setup or in the coverage of signals. Don t use it in the place beyond reach of signals. Place the unit outdoors, especially when starting it up. (Remark: The times of alert returns by tracker can be customized,it supports GPRS commands and PC commands settings,the comamnds are the same as sms comamnds ) 16 Accessories diagram 16.1. Fuel sensor diagram Red wire connect s+dc9-36v 22

Blue wire connects GND Black wire connects the tracker s Oil test wire 16.2 The temperature sensor diagram: VO+connects the tracker s temperature test wire VO-connects GND VDD connect s+dc9-36v GND connects GND Temperature detecting stick, put to test temperature place 23

16.3 摄 像 头 的 连 接 将 此 接 头 插 到 定 位 器 上 排 4PIN 连 接 器 里 16.4 RFID 的 连 接 将 此 接 线 头 连 接 到 输 出 的 紫 线 上 将 此 接 头 插 到 定 位 器 下 排 4PIN 连 接 器 里 24

将 此 下 排 接 头 和 RFID 相 连 将 此 上 排 接 头 和 摄 像 头 相 连 25