GEN Series with Diesel Engine Pumps

Hz GEN Series with Diesel Engine Pumps FIRE-FIGHTING BOOSTER SETS EN 1284, HIGH EFFICIENCY ELECTRIC PUMPS FHF and SHF SERIES WITH HIGH EFFICIENCY MOTORS AND DIESEL ENGINE PUMPS Cod. 191461 Rev ev.a.a Ed.11/211

2

CONTENTS General introduction... 1 Characteristics of electric pumps diesel engine pumps...1 13 Accessories and main components...13 26 Choice and selection...26 3 GEN..D/FHF series...3 37 Range...37 41 Hydraulic performance tables...41 3 Electrical performace tables...3 DFHF series... 9 GEN..D/FHF series...9 63 GEN..1D/FHF series...63 69 GEN..1D/FHF series...69 73 GEN..11D/FHF series...73 79 Hc pressure drop curve in suction kit...79 3

CONTENTS 91 GEN..D/SHF series...91 93 Range...93 96 Hydraulic performance tables...96 16 Electrical performance tables...16 17 DSHF series...17 111 GEN..D/SHF series...111 11 GEN..1D/SHF series...11 119 GEN..1D/SHF series...119 123 GEN..11D/SHF series...123 127 Hc pressure drop curve in suction kit...127 137 Accessories...137 12 Product description by technical specifications...12 4

GEN SERIES OF BOOSTER SETS GENERAL INTRODUCTION PRODUCT DESCRIPTION The GEN booster sets are built in conformity with EN1284 for automatic sprinkler systems and with UNI1779 for hydrant systems. In accordance with the above standards, all the main components of the booster set are factory connected and assembled. The configuration of the booster set depends on the number of pumps installed and on the type of electric motor or diesel engine, consistently with the type of supply chosen for the fire-fighting system from among those described in the standard. The water supply can be single, superior, duplicated or combined. Two main service pumps, one backing up the other, are normally installed for fire-fighting systems. The choice of electric motors or diesel engines depends on the level of reliability required from the system. In practice, fire-fighting booster sets have one electric service pump and one diesel service pump. Point 1.2 of EN 1284 states that for superior or duplicate water supplies, and if more than one pump is installed, no more than one service pump can be driven by the electric motor. This concept means that mixed assemblies, comprising electric or diesel pumps, have to be installed. This does not mean that it is not possible to have two electric pumps, one backing up the other, if the ascertained fire risk is low (single supplies) or if a diesel generator is already incorporated in the system. INTRODUCTION The Lowara GEN series of booster sets are therefore configured according to system requirements and initial considerations. They are also factory tested and comprise the following: One or two horizontal or vertical service pumps with the same hydraulic performance level, driven by an electric motor. Two horizontal service pumps with the same hydraulic performance level, driven by an electric motor and a diesel engine. A horizontal service pump driven by a diesel engine. The booster set is built and completed with the following main components: A Lowara SV series jockey electric pump (if required), controlled by an electric panel in the automatic mode. The jockey pump is automatically started and stopped by its pressure switch in order to restore supply pressure. This prevents the service pumps from starting and activating the main alarms. A control panel for each service pump. Two pressure switches for each service pump (if the first fails, the second repeats permission for the pump to start). On the discharge side of each service pump there is a on-off valve, a check valve and a tap for connection to the priming circuit for suction lift installations. Moreover, if the service pump works with a closed discharge line, a water recirculation tap has been applied to the pump body in order to prevent the pump from overheating. Discharge manifold connected to each service pump, fitted with a weld-on flange for connection to the system. Single base containing all the booster set components within a compact structure and ready for installation. To complete the pump station as requested by the standard, the GEN series of booster sets are fitted with the following accessories: Suction side kit. Flow meter. Alarm panel. Set of spare parts for diesel engines. Priming tank with accessories (for suction lift installations). 24L diaphragm tanks.

SET IDENTIFICATION TION CODE DIESEL ENGINE PUMP D FHF E A X / 32-2/D24 / B / IP INTRODUCTION Options: IP = Panels with IP protection. _ = Language group IT, EN, FI, PT. B = Language group EN, FR, DE, NL. Pump model. X = Automatic shut-off. A = Version with periodic self-test. EN 1284 Fire-fighting series. FHF = Pump code. SHF = Pump code. Diesel engine pump. DIESEL ENGINE PUMP SET GEN A X D / FHF 32-2/D24 / B / IP Options: IP = Panels with IP protection. _ = Language group IT, EN, FI, PT. B = Language group EN, FR, DE, NL. FHF = Pump code. SHF = Pump code. Diesel engine pump only. X = Automatic shut-off. A = Version with periodic self-test. GEN Fire-fighting series. RU SET WITH DIESEL ENGINE PUMP AND ELECTRIC PUMP GEN Y B X 1 1 D / FHF 32-2/4/D24 + 1SV1 / B / IP Options: CP = Clean contacts in electric pump panel. IP = Panels with IP protection. KV = Voltmeter kit. _ = Language group IT, EN, FI, PT. B = Language group EN, FR, DE, NL. Jockey pump code. FHF = Service pump code. SHF = Service pump code. D = With diesel engine pump. = Without electric jockey pump. 1 = With electric jockey pump. = Without electric service pump. 1 = With 1 electric service pump. X = Automatic shut-off. B = Basic version (only mark if electric service pump is present). A = Version with periodic self-test. Electric service pump electric start-up D = Direct start (Up to and including 22 kw). Y = Star/delta start. I = Impedance start. GEN Fire-fighting series. 6

REFERENCE STANDARDS The Lowara fire-fighting booster sets are EC certified in conformity with the following directives: - Machine Directive 26/42/EC. - Low Voltage Directive 26/9/EC. - Electromagnetic Compatibility Directive 24/18/EC. The electric pump performance is declared to be in accordance with the following standard: ISO 996-A Rotodynamic pumps hydraulic performance tests and acceptation criteria. The fire-fighting booster sets conform to the European fire-fighting Standard EN 1284. The automatic shut-off versions also conform to the UNI 1779 Italian Standard for hydrant systems. INTRODUCTION 7

P P GEN SERIES OF BOOSTER SETS FUNCTIONAL DIAGRAM FOR POSITIVE SUCTION HEAD INSTALLA ALLATIONS P P P P PRESSURE GAUGE MEMBRANE VESSEL M DRIVE UNIT LEVEL SWITCH INTRODUCTION FIRE FIGHTING SYSTEM PM P MQ PM FIRE FIGHTING SYSTEM PM MQ PUMP PRESSURE SWITCH STARTING OPEN DRAINAGE FLOW METER STRAINER FLOATING TAP PUMP RUNNING PRESSURE SWITCH CONNECTIONS ON-OFF VALVE NON RETURN VALVE RUBBER JOINT QF, CONTROL PANEL FOR DUTY ELECTRIC PUMP QF, CONTROL PANEL FOR DUTY DIESEL PUMP QPD, CONTROL PANEL FOR JOCKEY PUMP QAL, ALARMS CONTROL PANEL ECCENTRIC REDUCER WATER SUPPLY M M M WATER SUPPLY HYDRAULIC PIPING LINE POWER SUPPLY ELEMENTS ON REQUEST INSTALLATION BY CUSTOMER NOTE: ONLY APPROXIMATE DRAWING QF QPD QMTP QAL POWER SUPPLY POWER SUPPLY POWER SUPPLY POWER SUPPLY 1284-GEN11D_SPB-EN_B_SC GEN SERIES OF BOOSTER SETS FUNCTIONAL DIAGRAM FOR SUCTION LIFT INSTALLA ALLATIONS PRESSURE GAUGE MEMBRANE VESSEL P P P P M DRIVE UNIT LEVEL SWITCH PUMP ON-OFF VALVE PRESSURE SWITCH STARTING NON RETURN VALVE FIRE FIGHTING SYSTEM MQ FIRE FIGHTING SYSTEM OPEN DRAINAGE RUBBER JOINT MQ FLOW METER STRAINER QF, CONTROL PANEL FOR DUTY ELECTRIC PUMP QF, CONTROL PANEL FOR DUTY DIESEL PUMP QPD, CONTROL PANEL FOR JOCKEY PUMP QAL, ALARMS CONTROL PANEL FLOATING TAP ECCENTRIC REDUCER PM PUMP RUNNING PRESSURE SWITCH P WATER TANK SUPPLY PM CONNECTIONS PM M M M HYDRAULIC PIPING LINE POWER SUPPLY ELEMENTS ON REQUEST INSTALLATION BY CUSTOMER NOTE: ONLY APPROXIMATE DRAWING QF QPD QMTP QAL POWER SUPPLY POWER SUPPLY POWER SUPPLY POWER SUPPLY 1284-GEN11D_STB-EN_B_SC 8

GEN SERIES OF BOOSTER SETS MECHANICAL CONFIGURATION INTRODUCTION DENOMINAZIONE COMPONENTI GRUPPI DIESEL EN1284 REF. DESCRIPTION REF. DESCRIPTION 1 electric service pump 1 divergent on discharge line 2 diesel engine service pump 11 inspectable check valve 3 jockey pump discharge line 12 on-off valve on discharge line 4 control panels 13 pressure gauge pump suction line 14 discharge manifold 6* on-off valve on suction line 1 service pump starter (2x) 7 eccentric divergent 16 diaphragm tanks 8 vacuum pressure gauge 17 priming circuit tap 9 anti-vibration joint 18 recirculation circuit tap * Optional in case of positive suction head installation. gen11d-comp-en_b_tp 9

CHARACTERISTICS S OF THE PUMPS USED IN THE GEN SERIES OF BOOSTER SETS INTRODUCTION 1SV ELECTRIC PUMPS (JOCKEY PUMP) Multistage centrifugal vertical electric pumps. All metal parts in contact with pumped liquid are made of stainless steel. Version F: round flanges, in-line discharge and suction ports, AISI 34 (Standard version). Version N: round flanges, in-line discharge and suction ports, AISI 316 (Available on request). Reduced axial thrusts enable the use of standard motors that are easily found in the market. Standard supplied IE2 three-phase surface motors,7 kw are compliant with Regulation (EC) no. 64/29. Mechanical seal according to EN 1276 (ex DIN 2496) and ISO 369. Easy maintenance. No special tools required for assembly or disassembly. For other characteristics, consult the relative dedicated technical catalogue. FHF32, 4,, 6, 8, 1, 12 PUMP SERIES Single impeller cast iron horizontal centrifugal pump and shaft made of AISI 316L stainless steel. End suction and radial discharge ports. Impeller: made of AISI 316L stainless steel laser technology welded, for sizes 32, 4,, 6-12, or cast iron for sizes 6-16, 6-2, 6-2, 8, 1, 12. Hydraulic sizes and nominal diameter DN of suction and discharge ports according to EN 733 (ex DIN 242). Flanges according to EN 192-2 (ex UNI 2236) and DIN 232. Motor: motor/pump coupling with bracket, support, flexible coupling with spacer coupling and aligning and anchoring base. Standard supplied IE2 three-phase surface motors,7 kw are compliant with Regulation (EC) no. 64/29 and IEC 634-3. Performance levels according to EN 634-1. Back pull out design, impeller, adaptor and motor can be extracted without disconnecting the pump body from the pipes. For other characteristics, consult the relative dedicated technical catalogue. SHF32, 4,, 6, 8 PUMP SERIES Single impeller horizontal centrifugal pump with pump body and shaft made of AISI 316L stainless steel. End suction and radial discharge ports. Closed impeller made of AISI 316L stainless steel laser technology welded (for sizes 2, 32, 4,, 6-16/7 and 6-16/11A) or AISI CF8M cast stainless steel. Hydraulic sizes and nominal diameter DN of suction and discharge ports according to EN 733 (ex DIN 242). Flanges according to EN 192-1 (ex UNI 2236) and DIN 232. Motor: motor/pump coupling with bracket, support, flexible coupling with spacer coupling and aligning and anchoring base. Standard supplied IE2 three-phase surface motors,7 kw are compliant with Regulation (EC) no. 64/29 and IEC 634-3. Performance levels according to EN 634-1. Back pull out design, impeller, adaptor and motor can be extracted without disconnecting the pump body from the pipes. For other characteristics, consult the relative dedicated technical catalogue. 1

MAIN COMPONENTS FIRE-FIGHTING DIESEL ENGINE PUMP (D..) Diesel engine with coupling to service pump. Electric panel for control of diesel engine pump and battery charger. Diesel engine start circuit with two independent batteries. Double engine starting relay. Engine shut-off device from electric control (Electric stop). Fuel tank for diesel engine equipped with float. Base made of structural steel with epoxy powder painting RAL 1. The diesel engine pump is mounted on its own base complete with vibration-damping feet, and comes with a wall-mounted electric panel fitted with 3-metre cables ( metre length available on request), fuel tank with wall or floor mounting depending on capacity, floor-mounted or on-board batteries. Special versions of additional diesel fuel tank available on request. A panel mounting bracket kit for floor mounting and a jockey pump kit can be supplied on request. The installation of the diesel engine must provide for adequate ventilation and exhaust of combustion fumes. INTRODUCTION FIRE-FIGHTING SETS WITH DIESEL ENGINE PUMP (GEN..D) FIRE-FIGHTING SETS WITH ELECTRIC PUMP AND DIESEL ENGINE (GEN..D) On/off valves on the delivery side of each pump, ball valves with lever handle for diameters up to and including 1" 1/2 butterfly valve with lever handle from DN to DN1 diameter, butterfly valve with handwheel and reduction manual gear for DN12 diameter and above. Device for monitoring ON/OFF status included. Electrical connections by customer. (Lockable kit available on request). Recirculation device for each service pump. The re-circulation device allows a minimum capacity in order to prevent the pump overheating when working with closed delivery. It includes the activation pressure switch for the alarms of the pumps running, the test valve for checking the seal of the check valves, the couplings for any connecting pipes to the priming tank in the case of suction lift installation. The connection of each re-circulation to the suction tank or the priming tank is to be seen to by the person installing the equipment. Pressure gauge on the delivery side of each service pump between check valve and on/off valve. Inspectable check valve on the discharge side of each pump. Threaded coupling for diameters up to 1"1/2 included, flanged coupling for larger sizes. Painted iron delivery manifold (PN 16) and threaded stubs with relative caps for connecting any 24 litre membrane tanks. Blind and welding zinc-plated flanges. Two start-up pressure switches for every service pump. For the electric service pumps, start-up takes place through the pressure switch, but it must be manually stopped using the key-operated selector switch on the panel (excluding the version with automatic shut-off). For the electric jockey pump, if present, both start-up and stopping are determined by the pressure switch. Start-up pressure switch circuit for the service pump, including connecting pipes for the delivery manifold, recirculation circuit. This circuit includes on/off valve, a non-return valve, a discharge valve and various pipe fittings. The configuration of the circuit allows the pressure switch to intervene also when the relative on/off valve is closed. Various pipe fittings (copper, zinc-plated steel). Base made of bent sheet or structural iron with epoxy powder painting RAL 1. Control panel frame made of structural iron with epoxy powder painting RAL 1. Diesel engine with coupling to service pump. Vibration-damping joints on discharge side. Electric panel for control of diesel engine pump and battery charger. Diesel engine start circuit with two independent batteries. Length of cable connecting the batteries to the connection box 3 m. Double engine starting relay. Engine shut-off device from electric control (Electric stop). 11

Fuel tank for diesel engine. Special versions of additional diesel fuel tank available on request. Electric panel for each electric service pump. Starting: Direct (DOL) up to and including 22 kw, star/triangle from 3 kw up. INTRODUCTION The diesel engine pump is mounted on its own base complete with vibration-damping feet, and comes with a wall-mounted electric panel fitted with 3-metre cables ( metre length available on request), fuel tank with wall or floor mounting depending on capacity, floor-mounted or on-board batteries depending on size. A panel mounting bracket kit for floor mounting and a jockey pump kit can be supplied on request. The installation of the diesel engine must provide for adequate ventilation and exhaust of combustion fumes. The control panels for the electric pumps up to kw power supply are fixed on bracket. For higher powers, the control panels for electric pump service are floor mounted, instead the jockey electric pump panel is wall mounted fixed. Sets featuring a single diesel engine pump plus jockey pump are equipped with electric jockey pump with 1 x 23V single-phase power supply. SUCTION KIT The set is supplied with its suction side free from components. On request, for the SUCTION side of the individual service pump, TWO versions are available according to the system s installation type: POSITIVE SUCTION HEAD and SUCTION LIFT KIT Kit suitable for positive suction head or suction lift installation. The suction side of the individual pump includes: - Anti-vibration joint to attach to the pump inlet. - Eccentric cone or flanged stub pipe. - Vacuum pressure gauge. - On/off butterfly valve (optional in case of positive suction head installation) with lever handle for diameters up to DN1, butterfly valve with handwheel and reduction manual gear for DN12 and higher. Device for monitoring ON/OFF status included. Electrical connections by customer. (Valve lock kit available on request). - Weld-on flange. Conforming to the requirements of the EN 1284 Standard (chapter 1. and chapter 1.6). These requirements are connected with the type of installation and the measurement of the piping sections. (see tables on pages 14-143). OTHER VERSIONS As well as the basic GENDB versions (direct start-up), GENYB (star triangle start-up), GENIB (impedance start-up), the following versions are also available: GEN..A With periodic self-test function. There is a self-test circuit including a weekly clock on the electric panel of each electric service pump. For the time and date pre-set, the pump is started up and kept functioning for 1 minute. During this interval the check circuit checks that the pressure in the re-circulation circuit closes the pressure switch contact of the pump which is running. In the case of irregularities, the relative auxiliary self-test alarm relay available for remote signalling is activated and memorised. The EN1284 Standard does not provide for the presence of a self-test circuit but asks for periodic checks to be carried out by the user, hence the periodic self-test function cannot substitute the above checks. GEN..X GEN..X (For fire hydrant systems, UNI 1779) With automatic shut-off. There is an automatic shut-off circuit on the electric panel of each electric service pump. In certain situations, it allows automatic shut-off once the system pressure has been kept at higher values than the start-up values for at least twenty minutes. The self-test and automatic shut-off versions are available for each type of GEND.., GENY.., GENI.. start-up and in combination between them (See identification codes page). 12

ACCESSORIES SORIES AVAILABLE AILABLE ON REQUEST Protection against dry running for the electric jockey pump in one of the following versions: - Float switch, in case of suction lift. - Probes kit in case of suction lift (needs optional probe module in the electric jockey pump). - Minimum pressure switch, in case of positive suction head. Electric panel for remote status and alarm monitoring of one or two Lowara pumps installed in GEN fire-fighting booster sets, according to EN1284. In the electric service pump mode, the following conditions are visualised: Motor powered, pump start-up request, pump running, failure to start. In the diesel engine service pump mode, the following conditions are visualised: switch in non-automatic position, diesel engine fails to start after 6 attempts, pump running, QAL1284 Panel controller failure. Additionally: minimum suction tank or fuel level, minimum priming tank level, on-off valve on suction and discharge side not fully open. All the above conditions, required by EN1284, are visualised with signal LED s and buzzers. A buzzer alarm reset button and LED tester button are included. The control unit is also fitted out to signal the following general alarms, if present: - General alarm for incorrect electrical connection in the exchange contacts of: flow meter circuit valve, discharge pump, jockey pump status. - Fault in electrical connection in the exchange contact relative to panel 1 (electric pump/diesel engine pump). - Fault in electrical connection in the exchange contact relative Flow meter to panel 2 (electric pump/diesel engine pump). - Jockey pump overload; - Jockey pump running; - Discharge pump overload; - Battery low; - No communication with ModBus system. All the above conditions are visualised with signal LED s and on the display. The customer may decide to enable the buzzer. Further information available on page 144. Circuit for test flow of the service pumps. Includes the direct reading flow meter (sized according to the capacity of the service pump) according to the type of flow meter, connecting piping and straight piping upline from the instrument, on/off ball valve for diameters up to and including 2 butterfly valve with lever handle from DN6 to DN1 diameter, butterfly valve with handwheel and reduction manual gear for DN12 diameter and above. ON/OFF status monitoring included. New model of flow meter (P6) for diameters up to and including DN8. Diaphragm tank with relative ball valve, in the same number as that of the pumps present, for dampening any pressure oscillations in the system. 24 litre model with maximum pressure 8, 1 and 16 bar or 2 litre model with maximum pressure 2 bar according to the maximum head of the pumps. Priming tank for each service pump, in the case of suction lift installation. Accessories for the priming tank suck as float switch tap, level indicator, valves, automatic air discharger on each service pump, in the case of suction lift installation. INTRODUCTION All the main characteristics of the priming tanks, the flow meters and the available membrane tanks are shown in the accessories section. 13

SPECIAL EQUIPMENT ON REQUEST (Contact the Sales and technical Assistance Service) Sets for pumping sea water with electric pumps, valves, manifold and AISI 316 piping or compatible alloys. INTRODUCTION Non-standard supply power sets. Sets with two diesel engine service pumps. (See page 1). Sets with separate electric jockey pump supplied as a kit. Sets installed inside prefabricated boxes for outdoor use. Sets with oversized fuel tank. Sets with diesel engine pump with compressed air start system. Diesel engine pump with ambient air cooling device. Notes The set is supplied without a suction manifold in accordance with the EN1284 Standard (points 1.6.2.2 and 1.6.2.3) which provides for independent suction for each pump. Please see the EN1284 Standard on fixed systems and fire extinguishing Automatic sprinkler systems Design, installation and maintenance?- for sizing the suction piping, define whether the installation is to be considered suction lift or positive suction head for the use limits. The Standard ask that, whenever possible, the pumps are installed with positive suction head, otherwise priming tanks must be provided with suitable automatic devices for signalling and reintegration. The EN1284 Standard states that the water pressure should not exceed 12 bar (point 8.2.1). In some applications it is possible to have pressures of over 12 bar (point 8.2.2). In this case, pump sets with higher pressures than those within the regulatory limit are used. The catalogue also shows booster sets with pump closing head up to 1 metres suitable for such installations. 14

SPECIAL EQUIPMENT ON REQUEST INTRODUCTION 1

COMMAND PANEL FOR THE ELECTRIC SERVICE PUMP Painted metal casing (IP 4) complete with: INTRODUCTION General door-locking switch. Analogical ammeter. MAN AUT selector with extractable key only in automatic position. Keyboard for indicating electric voltage presence, correct phase sequence (three phase power supply), start-up request, pump functioning and no start-up, through LED lamps, lamp test button and starting and stopping buttons, according to the provisions of EN1284 paragraph 1.8.6. Inside: 12/24V transformer for auxiliary circuits and electronic board. Fuse holder and fuses for power and auxiliary circuits. Line contact maker (direct start-up up to 22 kw included), line and star/triangle contact makers (startriangle start-up), line contact makers and reactance switching (impedance start-up). Star/triangle exchanger timer or reactance switching. Relay for signalling no phase. Auxiliary relays. Current transformer. Terminal boards. Clean contacts (max. 24V, 1A) for activating acoustic/ visual alarms for no phase, pump on demand, pump running and start failure. Cable glands (excluding the versions to be fixed to the floor). Wiring diagram. Electric service pump panel 16

COMMAND PANEL FOR THE ELECTRIC JOCKEY PUMP Painted metal casing (IP ) complete with: General door-locking switch. Visual indicators for line, running, thermal shutdown. Manual automatic selector excluded. Inside: Transformer for 24V auxiliary circuits. Fuse holder and fuses for power and auxiliary circuits. Line contact maker. Overload cut-out switch. Pump shut-off timer ( 9 s). Terminal boards. Cable glands. Wiring diagram. INTRODUCTION Suitable for connecting to a float switch or a minimum pressure switch for preventing dry running. An optional level control module (supplied on request) allows the connection of probes with the possibility of regulating the sensitivity according to the hardness of the water. Electric jockey pump panel OPTIONS AVAILABLE AILABLE ON REQUEST CP alternative Series of clean contacts for checking the status of the electric service pump panel, as well as the contacts already provided for signalling alarms: No phase Motor running Selector position MAN-AUT- No start-up Start-up request Series of clean contacts for checking the status of the electric jockey pump: Pump running Thermal shutdown (overload) No water KV alternative Control panel for the electric service pump with analogical voltmeter and with phase switch. IP alternative Electric service pump panel with extra IP protection. 17

COMMAND PANEL FOR DIESEL ENGINE PUMP Painted metal casing (IP 4) complete with: INTRODUCTION Electronic control and management unit for the diesel engine. Display of alarms and status, battery voltage, speedometer, hour counter, alarm programming, date display, main signals and manual start button. Man-Auto- selector switch with key removable only in the auto position. Pair of emergency battery start buttons. General door-locking switch. Inside: Fuse holder and fuses for power and auxiliary circuits. Pair of battery chargers 12Vdc/24Vdc. Control unit for management of diesel engine and alarms. Auxiliary relays. Power circuits for engine heaters. Terminal boards. RS232 connector for communication port. Cable glands. Wiring diagram. Diesel engine pump panel The panel is supplied standard with clean alarm signal contacts (max. 1A,3Vdc/12Vac/277Vac): Non-automatic operating mode. Controller fault. Motor running. Failure to start. General alarm. Single-phase 1x23V standard power supply. OPTIONS AVAILABLE AILABLE ON REQUEST IP alternative Diesel engine service pump panel with additional IP protection. The set is supplied already assembled, calibrated and factory tested. The set is supplied complete with an instruction manual, pump manuals and wiring diagrams for the panels. For the sets including floor panels, the electric panels are sent together with the set in a separate pack and supplied with -metre long connecting cables (longer lengths available on request). The fitter is responsible for preparing the routes and installing the cables. 18

COMMAND PANEL DIMENSIONS SERVICE PUMP PANEL POWER (kw) PROTECTION B L H CLASS from,7 to 7, IP4 3 16 from 9,2 to 22 IP4 4 2 6 from 3 to 37 IP4 2 7 from 4 to IP4 6 2 8 from 7 to 9 IP4 6 3 1 from 11 to 16 IP4 8 4 17 IP: same dimensions as standard panels IP4 qe-serv-en_d_td Power over kw: floor cupboard INTRODUCTION JOCKEY PUMP PANEL PROTECTION CLASS B L H IP4 2 16 3 IP: same dimensions as standard panels IP4 qe-pil-en_b_td ENGINE PUMP PANEL PROTECTION CLASS B L H IP4 3 2 IP: same dimensions as standard panels IP4 qe-mtp1284_en_b_td * The control panels are included in the supply. 19

EN 1284 DIESEL ENGINE PUMP TANKS DIMENSIONS AND CAPACITY ACITY INTRODUCTION VOLUME (litres) B L H TYPE 3 26 28 1 6 38 33 1 9 42 42 12 2 13 42 42 14 2 19 4 134 2 24 7 7 14 2 serb-mtp-en_b_td Note: Special versions of additional diesel fuel tank available on request. 2

EN 1284 DIESEL ENGINE PUMP TANKS COMBINATIONS AND POSITIONING PUMP CAPACITY' (l) D.. GEN..D GEN..1D GEN..1D GEN..11D FHF32-12/D119 3 FHF32-12/D136 3 FHF32-16/D1 3 FHF32-16/D164 3 WALL MOUNTED WALL MOUNTED ON BOARD ON BOARD ON BOARD FHF32-2/D188 3 FHF32-2/D24 3 FHF4-12/D112 3 FHF4-12/D122 3 FHF4-12/D143 3 FHF4-16/D19 3 FHF4-16/D171 3 FHF4-2/D19 3 WALL MOUNTED WALL MOUNTED ON BOARD ON BOARD ON BOARD FHF4-2/D29 3 FHF4-2/D218 3 FHF4-2/D233 3 FHF4-2/D21 3 FHF-12/D119 3 FHF-12/D13 3 FHF-12/D139 3 FHF-16/D18 3 FHF-16/D174 3 FHF-2/D197 3 WALL MOUNTED WALL MOUNTED ON BOARD ON BOARD ON BOARD FHF-2/D29 3 FHF-2/D224 3 FHF-2/D237 6 FHF-2/D2 6 FHF6-12/D121 3 FHF6-12/D129 3 FHF6-12/D14 3 FHF6-16/D161 3 FHF6-16/D168 3 FHF6-16/D178 3 WALL MOUNTED WALL MOUNTED ON BOARD ON BOARD ON BOARD FHF6-2/D187 3 FHF6-2/D198 6 FHF6-2/D21 6 FHF6-2/D22 6 FHF6-2/D241 6 FHF6-2/D28 9 FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FHF8-16/D163 3 FHF8-16/D173 6 FHF8-2/D189 6 FHF8-2/D27 6 FHF8-2/D22 9 FHF8-2/D238 9 FHF8-2/D26 13 WALL MOUNTED WALL MOUNTED ON BOARD ON BOARD ON BOARD FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED pos-serb-fhf1284-en_c_td INTRODUCTION 21

EN 1284 DIESEL ENGINE PUMP TANKS COMBINATIONS AND POSITIONING PUMP CAPACITY' (l) D.. GEN..D GEN..1D GEN..11D INTRODUCTION FHF1-16/D1 3 FHF1-16/D16 6 FHF1-16/D18 6 WALL MOUNTED WALL MOUNTED ON BOARD ON BOARD FHF1-2/D168 6 FHF1-2/D192 6 FHF1-2/D23 9 FHF1-2/D213 9 FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FHF1-2/D2 6 WALL MOUNTED WALL MOUNTED ON BOARD ON BOARD FHF1-2/D221 9 FHF1-2/D23 13 FHF1-2/D24 19 FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FHF1-2/D267 19 FHF12-2/D18 6 WALL MOUNTED WALL MOUNTED ON BOARD ON BOARD FHF12-2/D26 9 FHF12-2/D216 13 FHF12-27/D224 19 FHF12-27/D237 19 FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FHF12-27/D23 24 FHF12-27/D266 24 pos-serb-fhf1-1284-en_c_td 22

EN 1284 DIESEL ENGINE PUMP TANKS COMBINATIONS AND POSITIONING PUMP CAPACITY' (l) D.. GEN..D GEN..1D GEN..1D GEN..11D SHF32-12/D121 3 SHF32-12/D136 3 SHF32-16/D1 3 SHF32-16/D168 3 SHF32-2/D188 3 WALL MOUNTED WALL MOUNTED ON BOARD ON BOARD ON BOARD SHF32-2/D24 3 SHF32-2/D222 3 SHF32-2/D242 3 SHF32-2/D26 3 SHF4-12/D112 3 SHF4-12/D126 3 SHF4-12/D143 3 SHF4-16/D19 3 SHF4-16/D171 3 SHF4-2/D19 3 WALL MOUNTED WALL MOUNTED ON BOARD ON BOARD ON BOARD SHF4-2/D29 3 SHF4-2/D218 3 SHF4-2/D233 3 SHF4-2/D21 3 SHF-12/D119 3 SHF-12/D13 3 SHF-12/D139 3 SHF-16/D18 3 SHF-16/D174 3 SHF-2/D197 3 WALL MOUNTED WALL MOUNTED ON BOARD ON BOARD ON BOARD SHF-2/D29 3 SHF-2/D224 3 SHF-2/D237 6 SHF-2/D2 6 SHF6-16/D119 3 SHF6-16/D129 3 SHF6-16/D137 3 SHF6-16/D168 3 SHF6-16/D177 3 WALL MOUNTED WALL MOUNTED ON BOARD ON BOARD ON BOARD SHF6-2/D192 3 SHF6-2/D23 6 SHF6-2/D21 6 SHF6-2/D24 6 SHF6-2/D2 9 FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED SHF8-16/D169 3 SHF8-16/D177 3 SHF8-16/D186 6 WALL MOUNTED WALL MOUNTED ON BOARD ON BOARD ON BOARD SHF8-2/D198 6 SHF8-2/D21 6 SHF8-2/D226 9 SHF8-2/D237 9 SHF8-2/D22 13 FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED FLOOR-MOUNTED SHF8-2/D27 19 pos-serb-shf1284-en_c_td INTRODUCTION 23

STARTING BATTERIES TERIES FOR DIESEL ENGINE PUMP EN 1284 COMBINATIONS AND SIZES INTRODUCTION TABELLA ABBINAMENTI POMPA SERVIZIO FH32-12 - BATTERIA AVVIAM. MTP GR TABLE OF DIESEL ENGINE PUMP FHF 32-12 COMBINATIONS DIESEL BATTERY DIESEL BATTERY ENGINE PUMP TYPE ENGINE PUMP TYPE TYPE TYPE DFHFE.. A B C D E DFHFE.. A B C D E PUMP PUMP 32-12/D119 6-2/D187 32-12/D136 6-2/D198 32-16/D1 6-2/D21 32-16/D164 6-2/D22 32-2/D188 6-2/D241 32-2/D24 6-2/D28 4-12/D112 8-16/D163 4-12/D122 8-16/D173 4-12/D143 8-2/D189 4-16/D19 8-2/D27 4-16/D171 8-2/D22 4-2/D19 8-2/D238 4-2/D29 8-2/D26 4-2/D218 1-16/D1 4-2/D233 1-16/D16 4-2/D21 1-16/D18-12/D119 1-2/D168-12/D13 1-2/D192-12/D139 1-2/D23-16/D18 1-2/D213-16/D174 1-2/D2-2/D197 1-2/D221-2/D29 1-2/D23-2/D224 1-2/D24-2/D237 1-2/D267-2/D2 12-2/D18 6-12/D121 12-2/D26 6-12/D129 12-2/D216 6-12/D14 12-27/D224 6-16/D161 12-27/D237 6-16/D168 12-27/D23 6-16/D178 12-27/D266 1284-FHF32-12_ab-en_a_tc 24

STARTING BATTERIES TERIES FOR DIESEL ENGINE PUMP EN 1284 TABLE TABELLA OF ABBINAMENTI DIESEL ENGINE POMPA SERVIZIO PUMP SHF SH32-8 32-8 - BATTERIA COMBINATIONS AVVIAM. MTP GRU DIESEL BATTERY ENGINE PUMP TYPE 32-12/D121 32-12/D136 32-16/D1 32-16/D168 32-2/D188 32-2/D24 32-2/D222 32-2/D242 32-2/D26 4-12/D112 4-12/D126 4-12/D143 4-16/D19 4-16/D171 4-2/D19 4-2/D29 4-2/D218 4-2/D233 4-2/D21-12/D119-12/D13-12/D139-16/D18-16/D174-2/D197-2/D29-2/D224-2/D237-2/D2 6-16/D119 6-16/D129 6-16/D137 6-16/D168 6-16/D177 6-2/D192 6-2/D23 6-2/D21 6-2/D24 6-2/D2 8-16/D169 8-16/D177 8-16/D186 8-2/D198 8-2/D21 8-2/D226 8-2/D237 8-2/D22 8-2/D27 TYPE DSHFE.. PUMP A B C D 1284-SHF32-8_ab-en_a_tc E INTRODUCTION 2

GEN SERIES OF BOOSTER SETS CHOICE AND SELECTION Criteria for choosing fire-fighting sets INTRODUCTION The correct choice of a fire-fighting set must consider various factors, including the correct sizing of the performance levels required for the system, local regulations and legislation, and especially the installation conditions relative to the installation site and whether a suction lift or a positive suction head is involved. Choosing the type of water supply The type of water supply and, therefore, the type of booster set to select depends on the type of system involved and is chosen according to the risk analysis performed by the designer. There is no written rule for identifying the correct number of pumps to install. GEN booster sets are normally designed so that every service pump can satisfy the following requirements: 1% of rated capacity with one or two pumps installed (one in service and the other in reserve). If three pumps are installed, the capacity of the pump will be % of the total rated capacity and the third service pump will be considered as a reserve. In these cases, when superior or duplicated water supplies are involved, only one pump must be driven by an electric motor. This type of configuration is available on request. Suction conditions of the booster set The type of installation, suction lift or positive suction head, tends to affect (negatively or positively) the hydraulic performance of the pump. Remembering that EN1284 recommends against using suction lift installations, the following condition given by EN1284 must be satisfied in order to use the pump curve correctly: NPSHd NPSHr +1 [m] Where: NPSHd is defined available. NPSHr is defined requested from the pump. As the suction check condition must be made at the max. requested flow, there can be different performance levels always respecting the NPSHd condition. To select the booster set, consult the dedicated sections. Choice and selection. Hydraulic performance levels. Suction lift or positive suction head installation. Performance levels of booster sets: using the tables The tables showing the hydraulic performance levels of booster sets indicate the flow values according to the risk class for precalculated systems followed by the respective pressure value. This value does not refer to pump performance but is net of the pressure drop on the pump discharge line, to the discharge manifold flange. This field is shown in grey and the selection must be made here, where performance levels comply with the reference standard which considers the following conditions: Maximum water speed in the service pump discharge piping 6 m/sec. NPSHd NPSHr + 1 at the maximum flow required. Max. difference in level of water considered 3,2 m (for positive suction head). Suction pressure drops due to valves, piping, suction kit 1, m (limit value). The reference suction conditions are the severest and most extreme that can occur. The values taken in the fields that are not in grey indicate booster set performance levels in areas outside the limits of the standard and must not be used to choose the set. 26

GEN SERIES OF BOOSTER SETS CHOICE AND SELECTION Method of selecting a fire-fighting booster set Referring to EN 1284, after identifying the risk classes of the activity to protect and performing the precalculation method, the flow and head values required for the fire-fighting system can be obtained. This data is used as follows: 1. Configuration of the booster set, choice of the number of service pumps and relative type of motor/engine (two pumps, one electric and the other driven by a diesel engine). 2. Installation conditions (e.g.. positive suction head), see performance levels for positive suction head installation. 3. Determination of service flow e.g.: 11 l/min risk class OH3. TABELLA DI PRESTAZIONI IDRAULICHE NETTE GRUPPI EN1284 SERIE FHF 2 poli Hz 1 POMPA DI SERVIZIO, INST SOPRAB RISK CLASS INTRODUCTION TYPE RATED OH2n OH3n FHF.. POWER Q = DELIVERY l/min 6 7 72 8 1 11 12 13 13 14 1 16 ELECTRIC PUMP m3/h 36 42 44 1 6 66 72 78 81 84 9 96 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 11,8 3,7 1,8 8, TABELLA 4. Determining DI PRESTAZIONI the IDRAULICHE head e.g.: NETTE 3 GRUPPI m. EN1284 SERIE 2,2 FHF 2 poli Hz 113,1 POMPA DI SERVIZIO, INST SOPRAB 27,3 18,2 34,8 RISK 26, CLASS 42,8 31,2 TYPE RATED 49,9 38,6 FHF.. POWER 6,4 48,8 Q = DELIVERY 69, 8,8 l/min 6 7 72 79, 8 1 11 68,1 12 13 13 14 1 16 ELECTRIC PUMP m3/h 36 42 44 1 6 66 72 78 81 84 9 96 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER -12/22-12/D119 1 x 2,2 16,8 13,7 12,3 11,8 9, 6,2 3,7,9-12/3-12/D13 1 x 3 19,9 17, 16,1 1,8 13,6 1, 8,,3 2,3-12/4-12/D139 1 x 4 24,3 21,8 2,6 2,2 18,3 1,3 13,1 1, 7,7 6,2 4,6-16/ -16/D18 1 x, 31,8 29,3 27,7 27,3 24,8 21,1 18,2 1, 11,4 9, 7,6-16/7-16/D174 1 x 7, 39,8 36,6 3,2 34,8 32, 29,1 26, 23, 2,2 18, 16,7 12,7-2/11A -2/D197 1 x 11,6 4,6 43,4 42,8 39, 34,8 31,2 27,3 23,1 2,9 18,6-2/11-2/D29 1 x 11 8, 2,6, 49,9 46,7 42,1 38,6 34,7 3,4 28,1 2,7 2,7 6,4 48,8 OH2n 69, 8,8 As can be seen, the required flow value enters the operating area in accordance with the standard, and the value of 79, 68,1 the corresponding head enters the field in grey. From the example shown above, we can identify the booster set that satisfies the request. The model is pump -2/11 providing a head of 38,6 m. OH3n 27

GEN SERIES OF BOOSTER SETS CHOICE AND SELECTION - POSITIVE SUCTION HEAD INSTALLA ALLATION EN1284 recommends always installing pumps in suction lift conditions, where possible If this is not possible, the pumps can be installed in positive suction head conditions according to the following rules: INTRODUCTION The height of the minimum water level at the pump axis must not be greater than 3,2 m. A foot valve must be installed in the lowest point of the suction piping. If more than one pump is installed, the suction piping must not be interconnected. optional Normal Liv. normale level Max 3,2 m Liv. Min X Min. level X Fig. 1 positive suction head installation diagram In accordance with EN 1284 (1.6.2.1), the suction piping, including all the valves and unions, must be designed to ensure that the NPSH available at the pump inlet exceeds the required NPSH by at least 1 m at the maximum required flow rate. NPSHd NPSHr + 1 When selecting the type of pump to use for the boosters sets, the installation conditions must be considered as these determine different pump performance levels. An example of how to choose and check of the installation conditions is shown below: considering the precalculation method, a suitable risk class for the system is identified, e.g.: OH3. For this risk class, the rated flow is 11 l/min (Qn), while the maximum requested flow is 13 l/min (Qm). Being in a positive suction head condition, the most difficult situation is considered, i.e.: the maximum difference in water level of 3,2 m, as indicated in the standard. Being aware of the rated flow 11 l/min and the pressure required for the system (e.g.: 3 m), the pump is selected according to the tables on page 44-4, making sure the performance rating lies inside the area shown in grey. The pump that satisfies the required work point is FHF-2/11. 28

GEN SERIES OF BOOSTER SETS CHOICE AND SELECTION - POSITIVE SUCTION HEAD INSTALLA ALLATION At this point, the installation conditions (positive suction head) must be checked at the maximum required flow. The following values are replaced in the known relation, NPSHd NPSHr + 1: NPSHr can be deduced from the table on page 4 which in this case is 4,6 m at the maximum requested flow. After replacing the value, the following will be true (water temperature around 1 C): NPSHd = 1,33 + (-3,2) - Hct Where 1,33 atmospheric pressure 3,2 geodetic difference in level Hct suction pressure drop ((valves, pipes, elbows..) The value of Hct considers the pressure drops of the suction kit, inclusive of vibration-proof joint, reduction cone and on-off valve (Hc), as well as the pressure drops relative to all the suction piping, foot valve, elbows, elbows, etc... INTRODUCTION The value of Hc at the maximum required flow of the selected pump can be found in the diagram on page 81. This value is,16 m. After entering it in the formula, we will have: Hct =,16 + X Where X is the pressure drop relative to all the suction piping Hence NPSHd NPSHr + 1. After replacing this, we will have: 1,33 + (-3,2) - Hct = 4,6 +1 1,33 + (-3,2),16 - X = 4,6 +1 which gives X = 1,37 m Maximum value of total drops to consider on the inlet piping in order to respect the conditions of the standard. Of course, this case was deliberately put in the worst suction conditions. The designer must check and set the values in an attempt to optimise suction conditions. 29

GEN SERIES OF BOOSTER SETS CHOICE AND SELECTION - POSITIVE SUCTION HEAD INSTALLA ALLATION Checking performance of the set at rated flow. INTRODUCTION The performance of the booster set must now be checked in the installation conditions of the example used up until now. Work point: Qn: 11 l/min H = 3 m The selected pump is FHF-2/11 Starting from the usual relation given by the standard, we will have: NPSHd NPSHr + 1 NPSHd = 1,33 + (-3,2) - Hct NPSHr can be deduced from the table on page 4 which in this case is 2,9 m at the rated flow. The value of Hct considers the pressure drops of the suction kit, inclusive of vibration-proof joint, reduction cone and on-off valve (Hc), as well as the pressure drops relative to all the suction piping, foot valve, elbows, elbows, etc... The value of Hc at the rated required flow of the selected pump can be found in the diagram on page 81. This value is,12 m. After entering it in the formula, we will have: Hct =,12 + X Where X is the pressure drop relative to all the suction piping Hence NPSHd NPSHr + 1. After replacing this, we will have: 1,33 + (-3,2) - Hct = 2,9 +1 1,33 + (-3,2),12 - X = 2,9 +1 which gives X = 3,11 m Value of the total drops to consider on the suction piping Taking the pressure value of the selected set, the value corresponds to 38,6 m at the rated flow. Therefore, the verification of the pressure values in the above suction conditions becomes: H = 38,6 -,12-3,11 = 3,4 m > 3 m which is the pressure required for the system The result satisfies the performance required for the system in the installation conditions of the example. 3

GEN SERIES OF BOOSTER SETS CHOICE AND SELECTION - SUCTION LIFT INSTALLA ALLATION Suction lift installation EN1284 recommends always installing pumps in suction lift conditions, where possible, according to the following rules: At least two thirds of the effective capacity of the suction tank must be above the level of the pump axis. The pump axis must not be more than 2 m above the minimum water level in the suction tank. Liv. Normal normale level INTRODUCTION 2/3 della of capacità effective effettiva capacity Max 2 m Liv. Min. Min level X Fig. 2 suction lift installation diagram In accordance with EN 1284 (1.6.2.1), the suction piping, including all the valves and unions, must be designed to ensure that the NPSH available at the pump inlet exceeds the required NPSH by at least 1 m at the maximum required flow rate. NPSHd NPSHr + 1 When selecting the type of pump to use for the boosters sets, the installation conditions must be considered as these determine different pump performance levels. An example of how to choose and check of the installation conditions is shown below: considering the precalculation method, a suitable risk class for the system is identified, e.g.: OH3. For this risk class, the rated flow is 11 l/min (Qn), while the maximum requested flow is 13 l/min (Qm). Being in the suction lift condition, a neutral situation is used in order to consider the water level on the same horizontal plane as the pump, without benefiting from any positive suction head. 31

GEN SERIES OF BOOSTER SETS CHOICE AND SELECTION - SUCTION LIFT INSTALLA ALLATION Being aware of the rated flow 11 l/min and the pressure required for the system (e.g.: 3 m), the pump is selected according to the tables on page 44-4, making sure the performance rating lies inside the area shown in grey. The pump that satisfies the required work point is FHF-2/11. INTRODUCTION At this point, the installation conditions (suction lift) must be checked at the maximum required flow. The following values are replaced in the known relation, NPSHd NPSHr + 1: NPSHr can be deduced from the table on page 4 which in this case is 4,6 m at the maximum requested flow. After replacing the value, the following will be true (water temperature around 1 C): NPSHd = 1,33 + () - Hct Where 1,33 atmospheric pressure geodetic difference in level Hct suction pressure drop (valves, pipes, elbows...) The value of Hct considers the pressure drops of the suction kit, inclusive of vibration-proof joint, reduction cone and on-off valve (Hc), as well as the pressure drops relative to all the suction piping, foot valve, elbows, elbows, etc The value of Hc at the maximum required flow of the selected pump can be found in the diagram on page 87. This value is,32 m. After entering it in the formula, we will have: Hct =,32 + X Where X is the pressure drop relative to all the suction piping Hence NPSHd NPSHr + 1. After replacing this, we will have: 1,33 + () - Hct = 4,6 +1 1,33 + (),32 - X = 4,6 +1 which gives X = 4,41 m Maximum value of total drops to consider on the inlet piping in order to respect the conditions of the standard. Of course, the case in point was deliberately tested in neutral suction conditions that neither benefit nor optimise suction. The designer must check and set the values in an attempt to make suction conditions as efficient as possible. 32

GEN SERIES OF BOOSTER SETS CHOICE AND SELECTION - SUCTION LIFT INSTALLA ALLATION Checking performance of the selected set at rated flow. The performance of the booster set must now be checked in the installation conditions of the example used up until now. Work point: Qn 11 l/min H = 3 m The selected pump is FHF-2/11 Starting from the usual relation given by the standard, we will have: NPSHd NPSHr + 1 NPSHd = 1,33 + () - Hct NPSHr can be deduced from the table on page 4 which in this case is 2,9 m at the rated flow. INTRODUCTION The value of Hct considers the pressure drops of the suction kit, inclusive of vibration-proof joint, reduction cone and on-off valve (Hc), as well as the pressure drops relative to all the suction piping, foot valve, elbows, elbows, etc... The value of Hc at the rated required flow of the selected pump can be found in the diagram on page 87. This value is,22 m. After entering it in the formula, we will have: Hct =,22 + X Where X is the pressure drop relative to all the suction piping Hence NPSHd NPSHr + 1. After replacing this, we will have: 1,33 + () - Hct = 2,9 +1 1,33 + (),22 - X = 2,9 +1 which gives X = 6,21 m Value of the total drops to consider on the suction piping Taking the pressure value of the selected set, the value corresponds to 38,6 m at the rated flow. Therefore, the verification of the pressure values in the above suction conditions becomes: H = 38,6 -,22-6,21 = 32,17 m < 3 m which is the pressure required for the system. The value obtained, doesn t satisfy the performance necessary for the system, but as is evident, we have used deliberately a neutral installation condition that it doesn t give benefits to the suction. It results that installed the pump with positive suction of 3 m, we will have a pressure value of 3,17 m that it satisfied the relation. 33

INTRODUCTION 34

GEN..D/FHF Series Fire-fighting booster sets EN 1284, electric pumps FHF series with high efficiency motors and diesel engine pumps Hz GEN..D/FHF 3

GEN..D/FHF 36

RANGE GEN..D/FHF RANGE The range of EN 1284 fire-fighting booster sets with diesel and electric service pumps and optional jockey pump to adapt to the specific needs of every application. D.. ENGINE PUMP Single fire-fighting centrifugal pump in horizontal design with cast iron casing, FHF series. Head up to 1 m. Flow up to 6 m 3 /h. GEN..D SERIES Fire-fighting sets with diesel engine centrifugal service pump, in horizontal design with cast iron casing, FHF series. Head up to 1 m. Flow up to 6 m 3 /h. GEN..D/FHF GEN..1D SERIES Fire-fighting sets with diesel engine service pump and electric jockey pump. The centrifugal service pump has horizontal design and cast iron casing. FHF series. Head up to 1 m. Flow up to 6 m 3 /h. GEN..1D SERIES Fire-fighting sets with diesel engine service pump and electric jockey pump. The centrifugal service pump has horizontal design and cast iron casing. FHF series. Head up to 1 m. Flow up to 13 m 3 /h. GEN..11D SERIES Fire-fighting sets with diesel engine service pump, electric service pump and electric jockey pump. The centrifugal service pump has horizontal design and cast iron casing. FHF series. Head up to 1 m. Flow up to 13 m 3 /h. 37

GEN..D/FHF GEN..D/FHF BOOSTER SETS SERIES HYDRAULIC TABELLA DI PRESTAZIONI PERFORMANCE IDRAULICHE TABLE SERIE AT 1SV 3SV Hz SV (JOCKEY 2p Hz PUMP) PUMP TYPE NOMINAL POWER l/min 12 2 Q = DELIVERY 2 3 3 4 m 3 /h,7 1,2 1, 1,8 2,1 2,4 kw HP H = TOTAL HEAD METRES COLUMN OF WATER 1SV 2,37, 12,2 12,2 11, 1,7 9, 7,9 6, 1SV 3,37, 18, 18, 17, 1,7 13,8 11,4 8,4 1SV 4,37, 23,7 23, 22,1 2,4 17,9 14,6 1,6 1SV,37, 29,3 28,9 27, 24,8 21,6 17,4 12, 1SV 6,37, 34,8 34,2 31,7 28,9 2, 2, 14, 1SV 7,37, 4,2 39,2 36,1 32,7 28,1 22,2 1,2 1SV 8,,7 48,1 47,9 4,2 41,8 36,8 3,4 22,4 1SV 9,,7 3,7 3,4,4 46,4 4,8 33, 24,6 1SV 1,,7 9,4 9,, 1, 44,7 36,6 26,6 1SV 11,,7 6,1 64, 6,4, 48, 39, 28, 1SV 12,7 1 73,3 73,1 69,3 64,3 7,1 47,6 3,7 1SV 13,7 1 79,2 78,9 74,8 69,4 61,6 1,2 38,2 1SV 1,7 1 9,9 9, 8,6 79,3 7,1 8,1 43,1 1SV 17 1,1 1, 1,2 14,9 1, 93,1 82,6 68,6 1,2 1SV 19 1,1 1, 117, 116,7 111, 13,2 91, 7,8 6,3 1SV 22 1,1 1, 134,6 134,1 127,4 118,1 14,4 86,1 63, 1SV 2 1, 2 12,6 12,4 14, 13,4 12, 99,1 72,7 Prestazioni conformi alle norme ISO 996 - Annex A. EN1284_pp_1sv-2p-en_a_th 38

GEN..D/FHF 32-8 BOOSTER SETS SERIES SERVICE TABELLA ABBINAMENTI PUMP JOCKEY POMPA SERVIZIO PUMP COMBINATIONS FH32-8 - POMPA PILOTA GRUPPI GEN 1 SERVICE PUMP JOCKEY PUMP ELECTRIC PUMP TYPE FHF.. PUMP 32-12/7 32-12/D119 32-12/11 32-12/D136 32-16/1 32-16/D1 32-16/22 32-16/D164 32-2/3 32-2/D188 32-2/4 32-2/D24 4-12/11 4-12/D112 4-12/1 4-12/D122 4-12/22 4-12/D143 4-16/3 4-16/D19 4-16/4 4-16/D171 4-2/ 4-2/D19 4-2/7 4-2/D29 4-2/11A 4-2/D218 4-2/11 4-2/D233 4-2/1 4-2/D21-12/22-12/D119-12/3-12/D13-12/4-12/D139-16/ -16/D18-16/7-16/D174-2/11A -2/D197-2/11-2/D29-2/1-2/D224-2/18-2/D237-2/22-2/D2 6-12/4 6-12/D121 6-12/ 6-12/D129 6-12/7 6-12/D14 6-16/11A 6-16/D161 6-16/11 6-16/D168 6-16/1 6-16/D178 6-2/1 6-2/D187 6-2/18 6-2/D198 6-2/22 6-2/D21 6-2/22 6-2/D22 6-2/3 6-2/D241 6-2/37 6-2/D28 8-16/1 8-16/D163 8-16/18 8-16/D173 8-2/22 8-2/D189 8-2/3 8-2/D27 8-2/37 8-2/D22 8-2/4 8-2/D238 8-2/ 8-2/D26 1SV 7 1SV 8 1SV 9 1SV 1 1SV 11 1SV 12 1SV 13 1SV 1 1SV 17 1SV 19 1284-FHF32-8_ap-en_b_tc GEN..D/FHF 39

GEN..D/FHF 1-12 BOOSTER SETS SERIES SERVICE TABELLA ABBINAMENTI PUMP JOCKEY POMPA SERVIZIO PUMP COMBINATIONS FH1-12 - POMPA PILOTA GRUPPI GE SERVICE PUMP JOCKEY PUMP GEN..D/FHF ELECTRIC PUMP TYPE FHF.. PUMP 1SV 7 1-16/18 1-16/D1 1-16/22 1-16/D16 1-16/3 1-16/D18 1-2/18 1-2/D168 1-2/3 1-2/D192 1-2/37 1-2/D23 1-2/4 1-2/D213 1-2/3 1-2/D2 1-2/4 1-2/D221 1-2/ 1-2/D23 1-2/7 1-2/D24 1-2/9 1-2/D267 12-2/3 12-2/D18 12-2/4 12-2/D26 12-2/ 12-2/D216 12-27/7 12-27/D224 12-27/9 12-27/D237 12-27/11 12-27/D23 12-27/132 12-27/D266 1SV 8 1SV 9 1SV 1 1SV 11 1SV 12 1SV 13 1SV 1 1SV 17 1SV 19 1284-FHF1-12_ap-en_b_tc 4

HYDRAULIC PERFORMANCE TABLE AT HZ (POSITIVE SUCTION HEAD) TABELLA DI PRESTAZIONI IDRAULICHE NETTE GRUPPO EN1284 SERIE FHF32 2 poli Hz, 1 POMPA DI SERVIZIO, ASP ESCLUSA INS SOPRA GEN..D/FHF 32 BOOSTER SETS SERIES RISK CLASS TYPE RATED LHn FHF.. POWER Q = DELIVERY l/min 1 1 2 22 2 27 3 37 4 42 4 ELECTRIC PUMP m3/h 6 9 12 14 1 17 18 23 24 26 27 3 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 32-12/7 32-12/D119 1 x,7 16,9 1,6 14,1 12,1 1,9 9,6 8,1 6,6 32-12/11 32-12/D136 1 x 1,1 21,9 2, 19,1 17,2 16,1 14,9 13, 12,1 7,1,2 32-16/1 32-16/D1 1 x 1, 27,3 2,6 24, 21,8 2, 19, 17,4 1,6 9, 7,2 32-16/22 32-16/D164 1 x 2,2 34,7 33,1 31, 29,3 27,9 26, 24,9 23,2 17,3 1, 12,7 1,2 32-2/3 32-2/D188 1 x 3 44,2 41,3 39,3 36,8 3,3 33,7 32, 3,1 23,4 2,8 18, 1, 32-2/4 32-2/D24 1 x 4 4,4 1,7 49, 46,8 4,2 43, 41,7 39,7 33,2 3,8 28,2 2,6 2, Performance levels relative to set with 1 service pump running and compliant with ISO 996 - Annex A. 1284_1pg-sp-fhf32-2p-en_a_th LHn = class of risk value referred to the required rated capacity (Tab.6 para 7.3.1 EN1284) Inlet pressure drops must be deducted. Make sure that these drops, added to the difference in level (max. 3.2m), are less than 4.m The values shown identify performance levels according to the reference standard EN1284. HYDRAULIC PERFORMANCE TABLE AT HZ (SUCTION LIFT) GEN..D/FHF 32 BOOSTER SETS SERIES TABELLA DI PRESTAZIONI IDRAULICHE NETTE GRUPPO EN1284 SERIE FHF32 2 poli Hz, 1 POMPA DI SERVIZIO, ASP ESCLUSA INS SOTTO TYPE RATED FHF.. POWER l/min 1 1 2 22 2 27 3 37 4 42 4 ELECTRIC PUMP m3/h 6 9 12 14 1 17 18 23 24 26 27 3 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 32-12/7 32-12/D119 1 x,7 16,9 1,6 14,1 12,1 1,9 9,6 8,1 6,6 32-12/11 32-12/D136 1 x 1,1 21,9 2, 19,1 17,2 16,1 14,9 13, 12,1 7,1,2 32-16/1 32-16/D1 1 x 1, 27,3 2,6 24, 21,8 2, 19, 17,4 1,6 9, 7,2 32-16/22 32-16/D164 1 x 2,2 34,7 33,1 31, 29,3 27,9 26, 24,9 23,2 17,3 1, 12,7 1,2 32-2/3 32-2/D188 1 x 3 44,2 41,3 39,3 36,8 3,3 33,7 32, 3,1 23,4 2,8 18, 1, 32-2/4 32-2/D24 1 x 4 4,4 1,7 49, 46,8 4,2 43, 41,7 39,7 33,2 3,8 28,2 2,6 2, Performance levels relative to set with 1 service pump running and compliant with ISO 996 - Annex A. 1284_1pg-st-fhf32-2p-en_a_th LHn = class of risk value referred to the required rated capacity (Tab.6 para 7.3.1 EN1284) Inlet pressure drops must be deducted. Make sure these drops are less than 4.m The values shown identify performance levels according to the reference standard EN1284. LHn RISK CLASS Q = DELIVERY GEN..D/FHF TABELLA DI PRESTAZIONI IDRAULICHE NPSHr GRUPPI EN1284 SERIE FHF32 2 poli Hz NPSH REQUIRED FOR PUMP SERIES FHF 32 RISK CLASS TYPE RATED LHn FHF.. POWER Q = DELIVERY l/min 1 1 2 22 2 27 3 3 37 4 4 ELECTRIC PUMP m 3 /h 6 9 12 14 1 17 18 21 23 24 27 3 PUMP kw NPSHr [METRES COLUMN OF WATER] 32-12/7 32-12/D119 1 x,7 1,6 1,6 1,7 1,8 2, 2,2 32-12/11 32-12/D136 1 x 1,1 1,6 1,6 1,7 1,8 2, 2,2 2,9 3,4 4, 32-16/1 32-16/D1 1 x 1, 2,2 2,4 2, 2,7 2,8 3, 3,6 3,9 4,4 32-16/22 32-16/D164 1 x 2,2 2,2 2,4 2, 2,7 2,8 3, 3,6 3,9 4,4,9 32-2/3 32-2/D188 1 x 3 2,7 2,9 3,1 3,3 3, 3,8 4,3 4,6 4,9, 32-2/4 32-2/D24 1 x 4 2,7 2,9 3,1 3,3 3, 3,8 4,3 4,6 4,9, 6,2 The declared NPSH values were obtained in the laboratory and refer to a single service pump 1284_1p-fhf32-2p_NPSHr-en_a_th LHn = class of risk value referred to the required rated capacity (Tab.6 para 7.3.1 EN1284) Check that NPSHd NPSHr+1m is satisfied 41

HYDRAULIC TABELLA DI PRESTAZIONI PERFORMANCE IDRAULICHE NETTE GRUPPI EN1284 TABLE SERIE AT FHF4 2 poli HZ Hz (POSITIVE 1 POMPA DI SERVIZIO, SUCTION ASP ESCLUSA INST HEAD) SOPRAB GEN..D/FHF 4 BOOSTER SETS SERIES RISK CLASS TYPE RATED OH1n GEN..D/FHF FHF.. POWER Q = DELIVERY l/min 3 3 37 4 6 7 72 7 8 9 1 11 ELECTRIC PUMP m3/h 18 21 23 32 36 42 44 4 48 4 6 66 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 4-12/11 4-12/D112 1 x 1,1 13,9 11,3 1, 9,3 3,4,7 4-12/1 4-12/D122 1 x 1, 18, 1,3 14, 13,3 7,4 4,7 4-12/22 4-12/D143 1 x 2,2 2,3 21,8 2, 19,8 14, 11,4 6,4, 3,6,6 4-16/3 4-16/D19 1 x 3 31,6 28,1 26,8 26, 19, 16, 1,8 9,2 7,6 4-16/4 4-16/D171 1 x 4 38,3 3,1 33,7 32,9 26, 23,6 18,1 16, 1, 11,7 4-2/ 4-2/D19 1 x, 46,4 42,7 41,2 4,4 33,1 29,7 23,3 21, 19,6 4-2/7 4-2/D29 1 x 7, 7, 3,1 1,6,7 43,8 4,7 34,8 33,2 31, 28, 4-2/11A 4-2/D218 1 x 11 63,6 7,8 6,2,2 47,8 44, 38,2 36, 34,8 31,1 4-2/11 4-2/D233 1 x 11 71,7 66, 64,3 63,4,7 2,3 4,8 44, 42,1 38,3 4-2/1 4-2/D21 1 x 1 8, 78,6 76,9 76, 68,4 6, 8,6 6,8, 1,1 42,6 Performance levels relative to set with 1 service pump running and compliant with ISO 996 - Annex A. 1284_1pg-sp-fhf4-2p-en_a_th OHn = class of risk value referred to the required rated capacity (Tab.6 para 7.3.1 EN1284) Inlet pressure drops must be deducted. Make sure that these drops, added to the difference in level (max. 3.2m), are less than 4.m The values shown identify performance levels according to the reference standard EN1284. HYDRAULIC PERFORMANCE TABLE AT HZ (SUCTION LIFT) GEN..D/FHF 4 BOOSTER SETS SERIES TABELLA DI PRESTAZIONI IDRAULICHE NETTE GRUPPI EN1284 SERIE FHF4 2 poli Hz 1 POMPA DI SERVIZIO, ASP ESCLUSA INST SOTTO RISK CLASS TYPE RATED OH1n FHF.. POWER Q = DELIVERY l/min 3 3 37 4 6 7 72 7 8 9 1 11 ELECTRIC PUMP m3/h 18 21 23 32 36 42 44 4 48 4 6 66 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 4-12/11 4-12/D112 1 x 1,1 13,9 11,3 1, 9,3 3,4,7 4-12/1 4-12/D122 1 x 1, 18, 1,3 14, 13,3 7,4 4,7 4-12/22 4-12/D143 1 x 2,2 2,3 21,8 2, 19,8 14, 11,4 6,4, 3,6,6 4-16/3 4-16/D19 1 x 3 31,6 28,1 26,8 26, 19, 16, 1,8 9,2 7,6 4-16/4 4-16/D171 1 x 4 38,3 3,1 33,7 32,9 26, 23,6 18,1 16, 1, 11,7 4-2/ 4-2/D19 1 x, 46,4 42,7 41,2 4,4 33,1 29,7 23,3 21, 19,6 4-2/7 4-2/D29 1 x 7, 7, 3,1 1,6,7 43,8 4,7 34,8 33,2 31, 28, 4-2/11A 4-2/D218 1 x 11 63,6 7,8 6,2,2 47,8 44, 38,2 36, 34,8 31,1 4-2/11 4-2/D233 1 x 11 71,7 66, 64,3 63,4,7 2,3 4,8 44, 42,1 38,3 4-2/1 4-2/D21 1 x 1 8, 78,6 76,9 76, 68,4 6, 8,6 6,8, 1,1 42,6 Performance levels relative to set with 1 service pump running and compliant with ISO 996 - Annex A. 1284_1pg-st-fhf4-2p-en_a_th OHn = class of risk value referred to the required rated capacity (Tab.6 para 7.3.1 EN1284) Inlet pressure drops must be deducted. Make sure these drops are less than 4.m The values shown identify performance levels according to the reference standard EN1284. 42

NPSH REQUIRED FOR PUMP SERIES FHF 4 TABELLA DI PRESTAZIONI IDRAULICHE NPSHr GRUPPI EN1284 SERIE FHF4 2 poli Hz 1 POMPA DI SERVIZIO RISK CLASS TYPE RATED OH1n OH1m FHF.. POWER Q = DELIVERY l/min 3 3 37 4 6 7 72 7 8 9 1 11 ELECTRIC PUMP m 3 /h 18 21 23 32 36 42 44 4 48 4 6 66 PUMP kw NPSHr [METRES COLUMN OF WATER] 4-12/11 4-12/D112 1 x 1,1 1,8 1,9 1,9 2,4 2,7 4-12/1 4-12/D122 1 x 1, 1,8 1,9 1,9 2,4 2,7 3,7 4-12/22 4-12/D143 1 x 2,2 1,8 1,9 1,9 2,4 2,7 3,7 4,1 4,6 6,3 4-16/3 4-16/D19 1 x 3 1,9 1,9 1,9 2,4 2,9 4,1 4,, 4-16/4 4-16/D171 1 x 4 1,9 1,9 1,9 2,4 2,9 4,1 4,, 6,2 4-2/ 4-2/D19 1 x, 2, 2,1 2,2 2,9 3,4 4, 4,9,3 4-2/7 4-2/D29 1 x 7, 2, 2,1 2,2 2,9 3,4 4, 4,9,3 6,3 4-2/11A 4-2/D218 1 x 11 1, 1,1 1,2 1,6 1,7 2,1 2,2 2,3 2,6 4-2/11 4-2/D233 1 x 11 1, 1,1 1,2 1,6 1,7 2,1 2,2 2,3 2,6 4-2/1 4-2/D21 1 x 1 1, 1,1 1,2 1,6 1,7 2,1 2,2 2,3 2,6 3, The declared NPSH values were obtained in the laboratory and refer to a single service pump OHn, OHm = class of risk value referred to the required rated and maximum capacity (Tab.6 para 7.3.1 EN1284) Check that NPSHd NPSHr+1m is satisfied at the maximum requested capacity 1284_1p-fhf4-2p_NPSHr-en_a_th GEN..D/FHF 43

HYDRAULIC TABELLA DI PRESTAZIONI PERFORMANCE IDRAULICHE NETTE GRUPPI EN1284 TABLE SERIE AT FHF 2 poli HZ Hz (POSITIVE 1 POMPA DI SERVIZIO, SUCTION INST SOPRAB HEAD) GEN..D/FHF BOOSTER SETS SERIES RISK CLASS TYPE RATED OH2n OH3n GEN..D/FHF FHF.. POWER Q = DELIVERY l/min 6 7 72 8 1 11 12 13 13 14 1 16 ELECTRIC PUMP m3/h 36 42 44 1 6 66 72 78 81 84 9 96 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER -12/22-12/D119 1 x 2,2 16,8 13,7 12,3 11,8 9, 6,2 3,7,9-12/3-12/D13 1 x 3 19,9 17, 16,1 1,8 13,6 1, 8,,3 2,3-12/4-12/D139 1 x 4 24,3 21,8 2,6 2,2 18,3 1,3 13,1 1, 7,7 6,2 4,6-16/ -16/D18 1 x, 31,8 29,3 27,7 27,3 24,8 21,1 18,2 1, 11,4 9, 7,6-16/7-16/D174 1 x 7, 39,8 36,6 3,2 34,8 32, 29,1 26, 23, 2,2 18, 16,7 12,7-2/11A -2/D197 1 x 11,6 4,6 43,4 42,8 39, 34,8 31,2 27,3 23,1 2,9 18,6-2/11-2/D29 1 x 11 8, 2,6, 49,9 46,7 42,1 38,6 34,7 3,4 28,1 2,7 2,7-2/1-2/D224 1 x 1 68,1 62,8 6,9 6,4 7,3 2,6 48,8 44,4 39,4 36,7 33,8-2/18-2/D237 1 x 18, 76, 71,7 7, 69, 66,6 62,3 8,8 4,7, 47,4 44,7 38,6-2/22-2/D2 1 x 22 86, 81,2 79, 79, 76,1 71,7 68,1 64, 9,4 6,8 4,1 48,1 41,4 Performance levels relative to set with 1 service pump running and compliant with ISO 996 - Annex A. 1284_1pg-sp-fhf-2p-en_a_th OHn = class of risk value referred to the required rated capacity (Tab.6 para 7.3.1 EN1284) Inlet pressure drops must be deducted. Make sure that these drops, added to the difference in level (max. 3.2m), are less than 4.m The values shown identify performance levels according to the reference standard EN1284. HYDRAULIC PERFORMANCE TABLE AT HZ (SUCTION LIFT) TABELLA DI PRESTAZIONI IDRAULICHE NETTE GRUPPI EN1284 SERIE FHF 2 poli Hz 1 POMPA DI SERVIZIO, INST SOTT GEN..D/FHF BOOSTER SETS SERIES RISK CLASS TYPE RATED OH2n OH3n FHF.. POWER Q = DELIVERY l/min 6 7 72 8 1 11 12 13 13 14 1 16 ELECTRIC PUMP m3/h 36 42 44 1 6 66 72 78 81 84 9 96 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER -12/22-12/D119 1 x 2,2 16,8 13,7 12,3 11,8 9, 6,2 3,7,9-12/3-12/D13 1 x 3 19,9 17, 16,1 1,8 13,6 1, 8,,3 2,3-12/4-12/D139 1 x 4 24,3 21,8 2,6 2,2 18,3 1,3 13,1 1, 7,7 6,2 4,6-16/ -16/D18 1 x, 31,8 29,3 27,7 27,3 24,8 21,1 18,2 1, 11,4 9, 7,6-16/7-16/D174 1 x 7, 39,8 36,6 3,2 34,8 32, 29,1 26, 23, 2,2 18, 16,7 12,7-2/11A -2/D197 1 x 11,6 4,6 43,4 42,8 39, 34,8 31,2 27,3 23,1 2,9 18,6-2/11-2/D29 1 x 11 8, 2,6, 49,9 46,7 42,1 38,6 34,7 3,4 28,1 2,7 2,7-2/1-2/D224 1 x 1 68,1 62,8 6,9 6,4 7,3 2,6 48,8 44,4 39,4 36,7 33,8-2/18-2/D237 1 x 18, 76, 71,7 7, 69, 66,6 62,3 8,8 4,7, 47,4 44,7 38,6-2/22-2/D2 1 x 22 86, 81,3 79, 79, 76,1 71,7 68,2 64,1 9, 6,9 4,2 48,2 41,6 Performance levels relative to set with 1 service pump running and compliant with ISO 996 - Annex A. 1284_1pg-st-fhf-2p-en_a_th OHn = class of risk value referred to the required rated capacity (Tab.6 para 7.3.1 EN1284) Inlet pressure drops must be deducted. Make sure these drops are less than 4.m The values shown identify performance levels according to the reference standard EN1284. 44

NPSH REQUIRED FOR PUMP SERIES FHF TABELLA DI PRESTAZIONI IDRAULICHE NPSHr GRUPPI EN1284 SERIE FHF 2 poli Hz 1 POMPA DI SERVIZIO RISK CLASS TYPE RATED OH2n OH2m OH3n OH3m FHF.. POWER Q = DELIVERY l/min 6 7 72 8 1 11 12 13 13 14 1 16 ELECTRIC PUMP m 3 /h 36 42 44 1 6 66 72 78 81 84 9 96 PUMP kw NPSHr [METRES COLUMN OF WATER] -12/22-12/D119 1 x 2,2 2,1 2,3 2,3 2,6 3,1 3, 3,9-12/3-12/D13 1 x 3 2,1 2,3 2,3 2,6 3,1 3, 3,9 4,4-12/4-12/D139 1 x 4 2,1 2,3 2,3 2,6 3,1 3, 3,9 4,4 4,7, -16/ -16/D18 1 x, 1,9 2,1 2,2 2, 2,9 3,2 3,6 4,2 4,6,1-16/7-16/D174 1 x 7, 1,9 2,1 2,2 2, 2,9 3,2 3,6 4,2 4,6,1 6, -2/11A -2/D197 1 x 11 1,8 1,9 2, 2,2 2,6 2,9 3,4 4,1 4,6,1-2/11-2/D29 1 x 11 1,8 1,9 2, 2,2 2,6 2,9 3,4 4,1 4,6,1 6,7-2/1-2/D224 1 x 1 1, 1,7 1,7 2, 2,4 2,7 3,1 3,6 3,9 4,2-2/18-2/D237 1 x 18, 1, 1,7 1,7 2, 2,4 2,7 3,1 3,6 3,9 4,2,1-2/22-2/D2 1 x 22 1, 1,7 1,7 2, 2,4 2,7 3,1 3,6 3,9 4,2,1 6,4 The declared NPSH values were obtained in the laboratory and refer to a single service pump OHn, OHm = class of risk value referred to the required rated and maximum capacity (Tab.6 para 7.3.1 EN1284) Check that NPSHd NPSHr+1m is satisfied at the maximum requested capacity 1284_1p-fhf-2p_NPSHr-en_a_th GEN..D/FHF 4

HYDRAULIC PERFORMANCE TABLE AT HZ (POSITIVE SUCTION HEAD) TABELLA DI PRESTAZIONI IDRAULICHE NETTE GRUPPI EN1284 SERIE FHF6 2 poli Hz 1 POMPA DI SERVIZIO, ASP ESCLUSA INST SOPRAB GEN..D/FHF 6 BOOSTER SETS SERIES RISK CLASS TYPE RATED OH3n OH4n GEN..D/FHF FHF.. POWER Q = DELIVERY l/min 8 9 1 11 12 13 14 1 18 2 21 23 ELECTRIC PUMP m3/h 48 4 6 66 72 81 84 9 18 12 126 138 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 6-12/4 6-12/D121 1 x 4 19,1 1,6 14,6 13, 12,3 1,9 8,7 7,9 6,2 6-12/ 6-12/D129 1 x, 22,7 19,6 18,8 17,8 16,7 1, 13, 12,7 11,2,7 6-12/7 6-12/D14 1 x 7, 27,1 24,3 23, 22,7 21,7 2,7 18,9 18,2 16,8 12, 8,1 6-16/11A 6-16/D161 1 x 11 32,7 29,2 28,3 27,2 26, 23,9 23,2 21,6 1,9 11, 9, 6-16/11 6-16/D168 1 x 11 3,9 32, 31, 3, 29,4 27,4 26,7 2,2 19,8 1,6 13,3 6-16/1 6-16/D178 1 x 1 41,9 38,9 38,1 37,1 36,1 34,2 33,6 32,2 27,2 23,2 21,1 16,3 6-2/1 6-2/D187 1 x 1 4,2 43,4 42,3 41,1 39,7 37,3 36,4 34,6 28,4 23,8 21,3 6-2/18 6-2/D198 1 x 18, 1,6,2 49,2 48,2 47, 44,9 44,1 42,4 36, 31,8 29,2 6-2/22 6-2/D21 1 x 22 9,1 7,2 6,3,3 4,2 2,1 1,4 49,8 44,1 39,6 37,1 31,6 6-2/22 6-2/D22 1 x 22 62,8 6,6 9,4 8, 6,4 3, 2,,2 42,1 3,7 32,1 6-2/3 6-2/D241 1 x 3 76,4 7, 73,9 72,6 71,1 68, 67, 6,4 7,8 1,6 48,2 4,6 6-2/37 6-2/D28 1 x 37 9,8 89,9 89, 88, 86,7 84, 83,7 81,8 74,8 68,8 6,4 7,7 Performance levels relative to set with 1 service pump running and compliant with ISO 996 - Annex A. 1284_1pg-sp-fhf6-2p-en_a_th OHn = class of risk value referred to the required rated capacity (Tab.6 para 7.3.1 EN1284) Inlet pressure drops must be deducted. Make sure that these drops, added to the difference in level (max. 3.2m), are less than 4.m The values shown identify performance levels according to the reference standard EN1284. HYDRAULIC PERFORMANCE TABLE AT HZ (SUCTION LIFT) GEN..D/FHF 6 BOOSTER SETS SERIES TABELLA DI PRESTAZIONI IDRAULICHE NETTE GRUPPI EN1284 SERIE FHF6 2 poli Hz 1 POMPA DI SERVIZIO, ASP ESCLUSA INST SOTTOB RISK CLASS TYPE RATED OH3n OH4n FHF.. POWER Q = DELIVERY l/min 8 9 1 11 12 13 14 1 18 2 21 23 ELECTRIC PUMP m3/h 48 4 6 66 72 81 84 9 18 12 126 138 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 6-12/4 6-12/D121 1 x 4 19,1 1,6 14,6 13, 12,3 1,9 8,7 7,9 6,2 6-12/ 6-12/D129 1 x, 22,7 19,6 18,8 17,8 16,7 1, 13, 12,7 11,2,7 6-12/7 6-12/D14 1 x 7, 27,1 24,3 23, 22,7 21,7 2,7 18,9 18,2 16,8 12, 8,1 6-16/11A 6-16/D161 1 x 11 32,7 29,2 28,3 27,2 26, 23,9 23,2 21,6 1,9 11, 9, 6-16/11 6-16/D168 1 x 11 3,9 32, 31, 3, 29,4 27,4 26,7 2,2 19,8 1,6 13,3 6-16/1 6-16/D178 1 x 1 41,9 38,9 38,1 37,1 36,1 34,2 33,6 32,2 27,2 23,2 21,1 16,3 6-2/1 6-2/D187 1 x 1 4,2 43,4 42,3 41,1 39,7 37,3 36,4 34,6 28,4 23,8 21,3 6-2/18 6-2/D198 1 x 18, 1,6,2 49,2 48,2 47, 44,9 44,1 42,4 36, 31,8 29,2 6-2/22 6-2/D21 1 x 22 9,1 7,2 6,3,3 4,2 2,1 1,4 49,8 44,1 39,6 37,1 31,6 6-2/22 6-2/D22 1 x 22 62,8 6,6 9,4 8, 6,4 3, 2,,2 42,1 3,7 32,1 6-2/3 6-2/D241 1 x 3 76,4 7, 73,9 72,6 71,1 68, 67, 6,4 7,8 1,6 48,2 4,6 6-2/37 6-2/D28 1 x 37 9,8 89,9 89, 88, 86,7 84, 83,7 81,8 74,8 68,8 6,4 7,7 Performance levels relative to set with 1 service pump running and compliant with ISO 996 - Annex A. 1284_1pg-st-fhf6-2p-en_a_th OHn = class of risk value referred to the required rated capacity (Tab.6 para 7.3.1 EN1284) Inlet pressure drops must be deducted. Make sure these drops are less than 4.m The values shown identify performance levels according to the reference standard EN1284. 46

NPSH REQUIRED FOR PUMP SERIES FHF 6 TABELLA DI PRESTAZIONI IDRAULICHE NPSHr GRUPPI EN1284 SERIE FHF6 2 poli Hz 1 POMPA DI SERVIZIO RISK CLASS TYPE RATED OH3n OH3m OH4n OH4m FHF.. POWER Q = DELIVERY l/min 8 9 1 11 12 13 14 1 18 2 21 23 ELECTRIC PUMP m 3 /h 48 4 6 66 72 81 84 9 18 12 126 138 PUMP kw NPSHr [METRES COLUMN OF WATER] 6-12/4 6-12/D121 1 x 4 1, 1,2 1,3 1,6 1,9 2,4 2,6 3,1 6-12/ 6-12/D129 1 x, 1, 1,2 1,3 1,6 1,9 2,4 2,6 3,1,1 6-12/7 6-12/D14 1 x 7, 1, 1,2 1,3 1,6 1,9 2,4 2,6 3,1,1 7, 6-16/11A 6-16/D161 1 x 11 2,4 2,4 2, 2,6 2,9 2,9 3,2 4,2,3 6, 6-16/11 6-16/D168 1 x 11 2,3 2,4 2, 2,7 2,8 2,9 3,1 3,7 4,4 4,9 6-16/1 6-16/D178 1 x 1 2,3 2,4 2, 2,7 2,8 2,9 3,1 3,7 4,4 4,9 6,6 6-2/1 6-2/D187 1 x 1 1,8 1,9 2, 2,1 2,3 2,4 2,6 3,4 4,,3 6-2/18 6-2/D198 1 x 18, 1,8 1,9 2, 2,1 2,3 2,4 2,6 3,4 4,3 4,9 6-2/22 6-2/D21 1 x 22 1,8 1,9 2, 2,1 2,3 2,4 2,6 3,4 4,3 4,9 6,6 6-2/22 6-2/D22 1 x 22 1,7 2, 2,2 2, 2,9 3,1 3,4 4,3,,4 6-2/3 6-2/D241 1 x 3 1,7 2, 2,2 2, 2,9 3,1 3,4 4,3,,4 6,2 6-2/37 6-2/D28 1 x 37 1,7 2, 2,2 2, 2,9 3,1 3,4 4,3,,4 6,2 The declared NPSH values were obtained in the laboratory and refer to a single service pump 1284_1p-fhf6-2p_NPSHr-en_a_th OHn, OHm = class of risk value referred to the required rated and maximum capacity (Tab.6 para 7.3.1 EN1284) Check that NPSHd NPSHr+1m is satisfied at the maximum requested capacity GEN..D/FHF 47

HYDRAULIC TABELLA DI PRESTAZIONI PERFORMANCE IDRAULICHE NETTE GRUPPI EN1284 TABLE SERIE AT FHF8 2 poli HZ Hz (POSITIVE 1 POMPA DI SERVIZIO, SUCTION ASP ESCLUSA INST HEAD) SOPRA GEN..D/FHF 8 BOOSTER SETS SERIES RISK CLASS TYPE RATED OH4n HH1n GEN..D/FHF FHF.. POWER Q = DELIVERY l/min 1 16 18 2 21 22 23 26 3216 3 36 36 ELECTRIC PUMP m3/h 9 99 18 123 126 132 138 16 193 21 216 219 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 8-16/1 8-16/D163 1 x 1 32,9 3,2 29,1 27,8 2,4 24,9 23,8 22,7 18,8 9,4 4,4 8-16/18 8-16/D173 1 x 18, 39, 3,6 34, 33,4 31,2 3,7 29,7 28,6 2,1 16,2 11,3 9, 8, 8-2/22 8-2/D189 1 x 22 48, 44,7 43,4 41,8 39, 38,3 37, 3,6 3,9 19,2 12,8 8-2/3 8-2/D27 1 x 3 9,9 6,9,8 4,4 1,9 1,3,1 48,9 44,7 34,2 28, 26,4 2,3 8-2/37 8-2/D22 1 x 37 7,8 67,3 6,8 63,9 6,4 9,6 7,9 6,1,1 34,7 26,1 8-2/4 8-2/D238 1 x 4 8, 78, 76, 74,8 71, 7,8 69,2 67,6 62, 47, 39,6 36, 8-2/ 8-2/D26 1 x 88,9 89,9 88,8 87, 84,8 84,2 82,9 81, 76,7 64, 6,7 4, 2,6 Performance levels relative to set with 1 service pump running and compliant with ISO 996 - Annex A. 1284_1pg-sp-fhf8-2p-en_a_th OHn, HHn = class of risk value referred to the required rated capacity (Tab.6 para 7.3.1, Tab.7 para 7.3.2 EN1284) Inlet pressure drops must be deducted. Make sure that these drops, added to the difference in level (max. 3.2m), are less than 4.m The values shown identify performance levels according to the reference standard EN1284. HYDRAULIC PERFORMANCE TABLE AT HZ (SUCTION LIFT) GEN..D/FHF 8 BOOSTER SETS SERIES TABELLA DI PRESTAZIONI IDRAULICHE NETTE GRUPPI EN1284 SERIE FHF8 2 poli Hz 1 POMPA DI SERVIZIO, ASP ESCLUSA INST SOTTO RISK CLASS TYPE RATED OH4n HH1n FHF.. POWER Q = DELIVERY l/min 1 16 18 2 21 22 23 26 3216 3 36 36 ELECTRIC PUMP m3/h 9 99 18 123 126 132 138 16 193 21 216 219 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 8-16/1 8-16/D163 1 x 1 32,9 3,2 29,1 27,8 2,4 24,9 23,8 22,7 18,8 9,4 4,4 8-16/18 8-16/D173 1 x 18, 39, 3,6 34, 33,4 31,2 3,7 29,7 28,6 2,1 16,2 11,3 9, 8, 8-2/22 8-2/D189 1 x 22 48, 44,7 43,4 41,8 39, 38,3 37, 3,6 3,9 19,2 12,8 8-2/3 8-2/D27 1 x 3 9,9 6,9,8 4,4 1,9 1,3,1 48,9 44,7 34,2 28, 26,4 2,3 8-2/37 8-2/D22 1 x 37 7,8 67,3 6,8 63,9 6,4 9,6 7,9 6,1,1 34,7 26,1 8-2/4 8-2/D238 1 x 4 8, 78, 76, 74,8 71, 7,8 69,2 67,6 62, 47, 39,6 36, 8-2/ 8-2/D26 1 x 88,9 89,9 88,8 87, 84,8 84,2 82,9 81, 76,7 64, 6,7 4, 2,6 Performance levels relative to set with 1 service pump running and compliant with ISO 996 - Annex A. 1284_1pg-st-fhf8-2p-en_a_th OHn, HHn = class of risk value referred to the required rated capacity (Tab.6 para 7.3.1, Tab.7 para 7.3.2 EN1284) Inlet pressure drops must be deducted. Make sure these drops are less than 4.m The values shown identify performance levels according to the reference standard EN1284. 48

NPSH REQUIRED FOR PUMP SERIES FHF 8 TABELLA DI PRESTAZIONI IDRAULICHE NPSHr GRUPPI EN1284 SERIE FHF8 2 poli Hz 1 POMPA DI SERVIZIO RISK CLASS TYPE RATED OH4n OH4m HH1n HH1m FHF.. POWER Q = DELIVERY l/min 1 16 18 2 21 22 23 26 3216 3 36 36 ELECTRIC PUMP m 3 /h 9 99 18 123 126 132 138 16 193 21 216 219 PUMP kw NPSHr [METRES COLUMN OF WATER] 8-16/1 8-16/D163 1 x 1 3,7 3,8 3,9 4, 4,1 4,2 4,2 4,,4 6,2 8-16/18 8-16/D173 1 x 18, 3,7 3,8 3,9 4, 4,1 4,2 4,2 4,,4 6,2 6, 6,8 8-2/22 8-2/D189 1 x 22 2,8 3, 3,1 3,3 3,4 3, 3,6 3,9,1 6,3 8-2/3 8-2/D27 1 x 3 2,8 3, 3,1 3,3 3,4 3, 3,6 3,9,1 6,3 6,9 7,3 8-2/37 8-2/D22 1 x 37 3, 3,1 3,3 3,6 3,6 3,8 3,9 4,4 6, 7,4 8-2/4 8-2/D238 1 x 4 2,4 2,6 2,7 3, 3,1 3,2 3,3 3,8 4,9,,7 8-2/ 8-2/D26 1 x 2,4 2,6 2,7 3, 3,1 3,2 3,3 3,8 4,9,,7,8 The declared NPSH values were obtained in the laboratory and refer to a single service pump 1284_1p-fhf8-2p_NPSHr-en_a_th OHn, OHm, HHn, HHm = class of risk value referred to the required rated and maximum capacity (Tab.6 para 7.3.1, Tab.7 para 7.3.2 EN1284) Check that NPSHd NPSHr+1m is satisfied at the maximum requested capacity GEN..D/FHF 49

HYDRAULIC PERFORMANCE TABLE AT HZ (POSITIVE SUCTION HEAD) GEN..D/FHF 1 BOOSTER SETS SERIES RISK CLASS TYPE RATED HH1n HH2n HH3n HH4n FHF.. POWER Q = DELIVERY l/min 1333 1 1667 23 29 3 3216 38 466 4266 4333 166 316 6 ELECTRIC PUMP m3/h 8 9 1 138 174 183 193 228 244 26 26 3 31 319 33 36 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 1-16/18 1-16/D1 1 x 18, 26,7 26, 2,6 2,2 22,9 19,9 19, 18, 13,9 11,8 1,2 9,6 3, 1,8 1-16/22 1-16/D16 1 x 22 33, 32,2 31,7 31,2 28,7 2,3 24,4 23,3 18,8 16,6 14,8 14,2 7,6,9 4,2 2,2 1-16/3 1-16/D18 1 x 3 42,3 41,2 4,8 4,3 37,8 34,6 33,6 32, 28,2 26, 24,2 23,6 16,9 1,1 13, 11,4,3 1-2/18 1-2/D168 1 x 18, 36,3 33, 32,7 28,6 23, 22, 2,3 13, 1,1 7,4 6,4 1-2/3 1-2/D192 1 x 3 49, 47, 46,9 43,7 39, 38,3 36,8 31, 28, 2, 24,7 1, 12,9 1-2/37 1-2/D23 1 x 37 6, 4,6 4, 1, 46,9 4,8 44,4 38,7 3,8 33,4 32,6 23,7 21,2 18,9 16, 1-2/4 1-2/D213 1 x 4 61, 6, 9, 7,1 3,6 2,6 1,4 46,3 43,7 41, 4,7 32,3 29,9 27,7 24,8 1-2/3 1-2/D2 1 x 3 4,6 2,1 47,7 41,8 4, 37,9 29,3 24,8 21,2 19,9,9 1-2/4 1-2/D221 1 x 4 68,8 66,9 63, 8,7 7,2,4 48,1 44,2 41, 39,9 27,2 23,6 2,3 1,9 1-2/ 1-2/D23 1 x 78, 76,9 74, 69,8 68, 66,9 6,2 6,6 3,6 2,6 4,6 37,2 34, 29,8 RISK CLASS GEN..D/FHF TYPE RATED FHF.. POWER HH4n l/min 1667 2 38 41 4 47 48 316 6 6366 6416 6 6716 67 ELECTRIC PUMP m3/h 1 1 228 249 273 282 288 3 319 33 36 382 38 39 43 4 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 1-2/7 1-2/D24 1 x 7 91,7 9, 86,9 7,9 71,7 66,1 63,7 62,1 8,7 2,9 49,3 38,3 29,3 28, 1-2/9 1-2/D267 1 x 9 12,9 11,6 98,2 87, 83,4 77,9 7,6 74, 7,7 64,9 61,3, 41, 4,2 38, 32, 31,1 Performance levels relative to set with 1 service pump running and compliant with ISO 996 - Annex A. 1284_1pg-sp-fhf1-2p-en_b_th HHn = class of risk value referred to the required rated capacity (Tab.7 par. 7.3.2 EN1284) Inlet pressure drops must be deducted. Make sure these drops, added to the difference in level (max 3,2mt), are less than 4,mt The values shown identify performance levels according to the reference standard EN1284. HYDRAULIC PERFORMANCE TABLE AT HZ (SUCTION LIFT) GEN..D/FHF 1 BOOSTER SETS SERIES HHn HH6n Q = DELIVERY RISK CLASS TYPE RATED HH1n HH2n HH3n HH4n FHF.. POWER Q = DELIVERY l/min 1333 1 1667 23 29 3 3216 38 466 4266 4333 166 316 6 ELECTRIC PUMP m3/h 8 9 1 138 174 183 193 228 244 26 26 3 31 319 33 36 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 1-16/18 1-16/D1 1 x 18, 26,7 26, 2,6 2,2 22,9 19,9 19, 18, 13,9 11,8 1,2 9,6 3, 1,8 1-16/22 1-16/D16 1 x 22 33, 32,2 31,7 31,2 28,7 2,3 24,4 23,3 18,8 16,6 14,8 14,2 7,6,9 4,2 2,2 1-16/3 1-16/D18 1 x 3 42,3 41,2 4,8 4,3 37,8 34,6 33,6 32, 28,2 26, 24,2 23,6 16,9 1,1 13, 11,4,3 1-2/18 1-2/D168 1 x 18, 36,3 33, 32,7 28,6 23, 22, 2,3 13, 1,1 7,4 6,4 1-2/3 1-2/D192 1 x 3 49, 47, 46,9 43,7 39, 38,3 36,8 31, 28, 2, 24,7 1, 12,9 1-2/37 1-2/D23 1 x 37 6, 4,6 4, 1, 46,9 4,8 44,4 38,7 3,8 33,4 32,6 23,7 21,2 18,9 16, 1-2/4 1-2/D213 1 x 4 61, 6, 9, 7,1 3,6 2,6 1,4 46,3 43,7 41, 4,7 32,3 29,9 27,7 24,8 1-2/3 1-2/D2 1 x 3 4,6 2,1 47,7 41,8 4, 37,9 29,3 24,8 21,2 19,9,9 1-2/4 1-2/D221 1 x 4 68,8 66,9 63, 8,7 7,2,4 48,1 44,2 41, 39,9 27,2 23,6 2,3 1,9 1-2/ 1-2/D23 1 x 78, 76,9 74, 69,8 68, 66,9 6,2 6,6 3,6 2,6 4,6 37,2 34, 29,8 RISK CLASS TYPE RATED HH4n HHn HH6n FHF.. POWER Q = DELIVERY l/min 1667 2 38 41 4 47 48 316 6 6366 6416 6 6716 67 ELECTRIC PUMP m3/h 1 1 228 249 273 282 288 3 319 33 36 382 38 39 43 4 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 1-2/7 1-2/D24 1 x 7 91,7 9, 86,9 7,9 71,7 66,1 63,7 62,1 8,7 2,9 49,3 38,3 29,3 28, 1-2/9 1-2/D267 1 x 9 12,9 11,6 98,2 87, 83,4 77,9 7,6 74, 7,7 64,9 61,3, 41, 4,2 38, 32, 31,1 Performance levels relative to set with 1 service pump running and compliant with ISO 996 - Annex A. 1284_1pg-st-fhf1-2p-en_b_th HHn = class of risk value referred to the required rated capacity (Tab.7 par. 7.3.2 EN1284) Inlet pressure drops must be deducted. Make sure these drops are less than 4,mt The values shown identify performance levels according to the reference standard EN1284.

NPSH REQUIRED FOR PUMP SERIES FHF 1 RISK CLASS TYPE RATED HH1n HH2n HH3n HH1m HH4n HH2m HH3m HH4m FHF.. POWER Q = DELIVERY l/min 1333 1 1667 23 29 3 3216 38 466 4266 4333 166 316 6 ELECTRIC PUMP m3/h 8 9 1 138 174 183 193 228 244 26 26 3 31 319 33 36 PUMP kw NPSHr [METRES COLUMN OF WATER] 1-16/18 1-16/D1 1 x 18, 6,3 6,4 6,6 7,3 8, 8,2 8,4 9,2 9, 9,8 9,9 11, 11,4 1-16/22 1-16/D16 1 x 22,,2,4 6,2 6,9 7, 7,2 7,9 8,3 8, 8,6 9,6 9,9 1,3 1,7 1-16/3 1-16/D18 1 x 3,,2,4 6,2 6,9 7, 7,2 7,9 8,3 8, 8,6 9,6 9,9 1,3 1,7 12,8 1-2/18 1-2/D168 1 x 18, 4,2 4,2 4,6,6 6, 6, 9,2 11,1 12,8 13, 1-2/3 1-2/D192 1 x 3 3,1 3,1 3,3 3, 3,6 3,7 4,2 4,6 4,9,1 7, 7,7 1-2/37 1-2/D23 1 x 37 3,1 3,1 3,3 3, 3,6 3,7 4,2 4,6 4,9,1 7, 7,7 8,4 9, 1-2/4 1-2/D213 1 x 4 3,1 3,1 3,3 3, 3,6 3,7 4,2 4,6 4,9,1 7, 7,7 8,4 9, 1-2/3 1-2/D2 1 x 3 4,7,,3,4,4,7,8,9 6, 6,3 1-2/4 1-2/D221 1 x 4 4,6 4,7 4,7 4,8 4,8 4,8 4,9 4,9 4,9,1,2,2,3 1-2/ 1-2/D23 1 x 4,6 4,7 4,7 4,8 4,8 4,8 4,9 4,9 4,9,1,2,2,3 TYPE RATED HH4n FHF.. POWER Q = DELIVERY l/min 1667 2 38 41 4 47 48 316 6 6366 6416 6 6716 67 ELECTRIC PUMP m3/h 1 1 228 249 273 282 288 3 319 33 36 382 38 39 43 4 PUMP kw NPSHr [METRES COLUMN OF WATER] 1-2/7 1-2/D24 1 x 7 4,6 4,7 4,8 4,9,,,,1,2,3,8 6,6 6,7 1-2/9 1-2/D267 1 x 9 4,6 4,7 4,8 4,9,,,,1,2,3,8 6,6 6,7 6,9 7,8 7,9 The declared NPSH values were obtained in the laboratory and refer to a single service pump 1284_1p-fhf1-2p_NPSHr-en_a_th HHn, HHm = class of risk value referred to the required rated and maximum capacity (Tab.7 para 7.3.2 EN1284) Check that NPSHd NPSHr+1m is satisfied at the maximum requested capacity HHn HH6n RISK CLASS HH4m HHm HH6m GEN..D/FHF 1

HYDRAULIC PERFORMANCE TABLE AT HZ (POSITIVE SUCTION HEAD) TABELLA DI PRESTAZIONI IDRAULICHE NETTE GRUPPI EN1284 SERIE FHF12 2 poli Hz 1 POMPA DI SERVIZIO, ASP ESCLUSA INST SOPRA GEN..D/FHF 12 BOOSTER SETS SERIES RISK CLASS TYPE RATED HH6n HH7n HH8n HH9n HH1n FHF.. POWER Q = DELIVERY l/min 2 2 48 48 7 6 64 6716 6783 7 7983 84 8667 8966 9333 983 1 1333 1833 ELECTRIC PUM m3/h 12 1 288 291 342 36 384 43 47 4 479 4 2 38 6 7 6 62 6 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 12-2/3 12-2/D18 1 x 3 32,8 29,8 28,4 19,8 19,6 1,8 14,4 12,6 11,2 1,9 7,6 12-2/4 12-2/D26 1 x 4 47,2 44,8 43, 34,8 34,6 3,3 28,6 26,4 24, 24,1 19,7 16,6 13,9 12,1 12-2/ 12-2/D216 1 x 7,4,1 4, 4,6 4,4 41, 39,3 36,8 34,8 34,3 29,3 2,6 22,3 2, 17,4 14,1 12-27/7 12-27/D224 1 x 7 6,1 63,7 6,,8 1, 49,8 47,3 4,3 44,8 39,8 36,1 32,7 3, 27,9 24,6 22,3 12-27/9 12-27/D237 1 x 9 7,3 73,6 67, 66,8 62,8 61,1 8,8 6,8 6,3 1,2 47,4 43,8 41,4 38, 34,8 32,2 27, 12-27/11 12-27/D23 1 x 11 88,2 8,4 79,2 79, 7,1 73, 71,2 69,2 68,8 63, 9,,7 3, 49,9 4,8 42,8 37,6 33,1 12-27/132 12-27/D266 1 x 132 97, 94,8 88,6 88,4 84,7 83,2 81,1 79,2 78,8 74, 7,3 66,8 64, 61,7 8,,4,7 46,8 4, Performance levels relative to set with 1 service pump running and compliant with ISO 996 - Annex A. HHn = class of risk value referred to the required rated capacity (Tab.7 par. 7.3.2 EN1284) Inlet pressure drops must be deducted. Make sure these drops, added to the difference in level (max 3,2mt), are less than 4,mt The values shown identify performance levels according to the reference standard EN1284. 1284_1pg-sp-fhf12-2p-en_b_th GEN..D/FHF HYDRAULIC PERFORMANCE TABLE AT HZ (SUCTION LIFT) TABELLA DI PRESTAZIONI IDRAULICHE NETTE GRUPPI EN1284 SERIE FHF12 2 poli Hz 1 POMPA DI SERVIZIO, ASP ESCLUSA INST SOTTOB GEN..D/FHF 12 BOOSTER SETS SERIES TYPE RATED HH6n HH7n HH8n HH9n FHF.. POWER Q = DELIVERY l/min 2 2 48 48 7 6 64 6716 6783 7 7983 84 8667 8966 9333 983 1 1333 1833 ELECTRIC PUMP m3/h 12 1 288 291 342 36 384 43 47 4 479 4 2 38 6 7 6 62 6 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 12-2/3 12-2/D18 1 x 3 32,8 29,8 28,4 19,8 19,6 1,8 14,4 12,6 11,2 1,9 7,6 12-2/4 12-2/D26 1 x 4 47,2 44,8 43, 34,8 34,6 3,3 28,6 26,4 24, 24,1 19,7 16,6 13,9 12,1 12-2/ 12-2/D216 1 x 7,4,1 4, 4,6 4,4 41, 39,3 36,8 34,8 34,3 29,3 2,6 22,3 2, 17,4 14,1 12-27/7 12-27/D224 1 x 7 6,1 63,7 6,,8 1, 49,8 47,3 4,3 44,8 39,8 36,1 32,7 3, 27,9 24,6 22,3 12-27/9 12-27/D237 1 x 9 7,3 73,6 67, 66,8 62,8 61,1 8,8 6,8 6,3 1,2 47,4 43,8 41,4 38, 34,8 32,2 27, 12-27/11 12-27/D23 1 x 11 88,2 8,4 79,2 79, 7,1 73, 71,2 69,2 68,8 63, 9,,7 3, 49,9 4,8 42,8 37,6 33,1 12-27/132 12-27/D266 1 x 132 97, 94,8 88,6 88,4 84,7 83,2 81,1 79,2 78,8 74, 7,3 66,8 64, 61,7 8,,4,7 46,8 4, Performance levels relative to set with 1 service pump running and compliant with ISO 996 - Annex A. HHn = class of risk value referred to the required rated capacity (Tab.7 par. 7.3.2 EN1284) Inlet pressure drops must be deducted. Make sure these drops are less than 4,mt The values shown identify performance levels according to the reference standard EN1284. HH1n RISK CLASS 1284_1pg-st-fhf12-2p-en_b_th TABELLA DI PRESTAZIONI IDRAULICHE NPSHr EN1284 SERIE FHF12 2 poli Hz 1 POMPA DI SERVIZIO NPSH REQUIRED FOR PUMP SERIES FHF 12 RISK CLASS TYPE RATED HH6n HH7n HH8n HH9n HH1n HH6m HH7m HH8m HH9m HH1m FHF.. POWER Q = DELIVERY l/min 2 2 48 48 7 6 64 6716 6783 7 7983 84 8667 8966 9333 983 1 1333 1833 ELECTRIC PUMP m 3 /h 12 1 288 291 342 36 384 43 47 4 479 4 2 38 6 7 6 62 6 PUMP kw NPSHr [METRES COLUMN OF WATER] 12-2/3 12-2/D18 1 x 3 6, 6,8 8, 8, 9,1 9,3 9,6 9,9 9,9 1,4 12-2/4 12-2/D26 1 x 4 6,1 6,2 7,1 7,1 7,6 7,7 8, 8,3 8,3 8,9 9, 1, 1,4 12-2/ 12-2/D216 1 x 6,1 6,2 7,1 7,1 7,6 7,7 8, 8,3 8,3 8,9 9, 1, 1,4 1,8 11, 12-27/7 12-27/D224 1 x 7 7,8 8,3 8,3 8, 8,6 8,7 8,8 8,9 9,3 9,7 1,1 1, 11,1 11,9 12,7 12-27/9 12-27/D237 1 x 9 6, 6,9 6,9 7,2 7,3 7, 7,7 7,7 8,1 8,4 8,8 9, 9,4 9,9 1,4 11,4 12-27/11 12-27/D23 1 x 11 6, 6,9 6,9 7,2 7,3 7, 7,7 7,7 8,1 8,4 8,8 9, 9,4 9,9 1,4 11,4 12, 12-27/132 12-27/D266 1 x 132 6, 6,9 6,9 7,2 7,3 7, 7,7 7,7 8,1 8,4 8,8 9, 9,4 9,9 1,4 11,4 12, 14,8 The declared NPSH values were obtained in the laboratory and refer to a single service pump HHn, HHm = class of risk value referred to the required rated and maximum capacity (Tab.7 para 7.3.2 EN1284) Check that NPSHd NPSHr+1m is satisfied at the maximum requested capacity 1284_1p-fhf12-2p_NPSHr-en_a_th 2

GEN..D/FHF 1-12 BOOSTER SETS TABELLA DATI ELETTRICI GRUPPI GEN..D/FHF 2 poli Hz ELECTRICAL DATA A TABLE AT Hz SERVICE PUMP ELECTRIC JOCKEY PUMP CURRENT (*) ABSORBED SET 3 X 4 V 1 x 23V 3x4 TYPE NOMINAL 1x23V 3x4V FHF.. POWER ELECTRIC Pn In TYPE Pn In In GEN..D GEN..1D GEN..1D GEN..11D PUMP PUMP kw A kw A A A A A A 32-12/7 32-12/D119,7 1,76 1SV 7,37 2,82 1,3 3,8 4,8 6,1 32-12/11 32-12/D136 1,1 2,36 1SV 8, 3,88 1,48 3 6,9,4 6,8 32-16/1 32-16/D1 1, 3,2 1SV 8, 3,88 1,48 3 6,9 6, 7, 32-16/22 32-16/D164 2,2 4,64 1SV 9, 3,88 1,48 3 6,9 7,6 9,1 32-2/3 32-2/D188 3,91 1SV 11, 3,88 1,48 3 6,9 8,9 1,4 32-2/4 32-2/D24 4 7, 1SV 12,7 4,88 1,76 3 7,9 1, 12,3 4-12/11 4-12/D112 1,1 2,36 1SV 7,37 2,82 1,3 3,8,4 6,7 4-12/1 4-12/D122 1, 3,2 1SV 8, 3,88 1,48 3 6,9 6, 7, 4-12/22 4-12/D143 2,2 4,64 1SV 8, 3,88 1,48 3 6,9 7,6 9,1 4-16/3 4-16/D19 3,91 1SV 9, 3,88 1,48 3 6,9 8,9 1,4 4-16/4 4-16/D171 4 7, 1SV 1, 3,88 1,48 3 6,9 1, 12, 4-2/ 4-2/D19, 11, 1SV 11, 3,88 1,48 3 6,9 14, 1, 4-2/7 4-2/D29 7, 14,3 1SV 12,7 4,88 1,76 3 7,9 17,3 19,1 4-2/11A 4-2/D218 11 19,8 1SV 13,7 4,88 1,76 3 7,9 22,8 24,6 4-2/11 4-2/D233 11 19,8 1SV 1,7 4,88 1,76 3 7,9 22,8 24,6 4-2/1 4-2/D21 1 26,2 1SV 17 1,1 6,77 2,36 3 9,8 29,2 31,6-12/22-12/D119 2,2 4,64 1SV 7,37 2,82 1,3 3,8 7,6 9, -12/3-12/D13 3,91 1SV 8, 3,88 1,48 3 6,9 8,9 1,4-12/4-12/D139 4 7, 1SV 8, 3,88 1,48 3 6,9 1, 12, -16/ -16/D18, 11, 1SV 9, 3,88 1,48 3 6,9 14, 1, -16/7-16/D174 7, 14,3 1SV 1, 3,88 1,48 3 6,9 17,3 18,8-2/11A -2/D197 11 19,8 1SV 12,7 4,88 1,76 3 7,9 22,8 24,6-2/11-2/D29 11 19,8 1SV 12,7 4,88 1,76 3 7,9 22,8 24,6-2/1-2/D224 1 26,2 1SV 1,7 4,88 1,76 3 7,9 29,2 31, -2/18-2/D237 18, 32,9 1SV 1,7 4,88 1,76 3 7,9 3,9 37,7-2/22-2/D2 22 39,1 1SV 17 1,1 6,77 2,36 3 9,8 42,1 44, 6-12/4 6-12/D121 4 7, 1SV 7,37 2,82 1,3 3,8 1, 11,9 6-12/ 6-12/D129, 11, 1SV 8, 3,88 1,48 3 6,9 14, 1, 6-12/7 6-12/D14 7, 14,3 1SV 8, 3,88 1,48 3 6,9 17,3 18,8 6-16/11A 6-16/D161 11 19,8 1SV 9, 3,88 1,48 3 6,9 22,8 24,3 6-16/11 6-16/D168 11 19,8 1SV 1, 3,88 1,48 3 6,9 22,8 24,3 6-16/1 6-16/D178 1 26,2 1SV 1, 3,88 1,48 3 6,9 29,2 3,7 6-2/1 6-2/D187 1 26,2 1SV 11, 3,88 1,48 3 6,9 29,2 3,7 6-2/18 6-2/D198 18, 32,9 1SV 12,7 4,88 1,76 3 7,9 3,9 37,7 6-2/22 6-2/D21 22 39,1 1SV 12,7 4,88 1,76 3 7,9 42,1 43,9 6-2/22 6-2/D22 22 39,1 1SV 13,7 4,88 1,76 3 7,9 42,1 43,9 6-2/3 6-2/D241 3 3,6 1SV 1,7 4,88 1,76 3 7,9 6,6 8,4 6-2/37 6-2/D28 37 6,8 1SV 17 1,1 6,77 2,36 3 9,8 68,8 71,2 8-16/1 8-16/D163 1 26,2 1SV 9, 3,88 1,48 3 6,9 29,2 3,7 8-16/18 8-16/D173 18, 32,9 1SV 1, 3,88 1,48 3 6,9 3,9 37,4 8-2/22 8-2/D189 22 39,1 1SV 11, 3,88 1,48 3 6,9 42,1 43,6 8-2/3 8-2/D27 3 3,6 1SV 12,7 4,88 1,76 3 7,9 6,6 8,4 8-2/37 8-2/D22 37 6,8 1SV 1,7 4,88 1,76 3 7,9 68,8 7,6 8-2/4 8-2/D238 4 78, 1SV 1,7 4,88 1,76 3 7,9 81, 82,8 8-2/ 8-2/D26 9, 1SV 17 1,1 6,77 2,36 3 9,8 98, 1,4 ENMTP-FHF_2p-en_d_te (*) The current indicated is the maximum current absorbed. At the set 3x4V three-phase power supply GEN..1D and GEN..11D to add the control panel current of the engine pump (GEN..D) 1x23V The sets GEN..1D have the electric jockey pump 1x23V single-phase power supply. GEN..D/FHF 3

GEN..D/FHF GEN..D/FHF 1-12 BOOSTER SETS TABELLA DATI ELETTRICI GRUPPI GEN..D/FHF 2 poli Hz ELECTRICAL DATA A TABLE AT Hz SERVICE PUMP ELECTRIC JOCKEY PUMP CURRENT (*) ABSORBED SET 3 X 4 V 1 x 23V 3x4 TYPE NOMINAL 1x23V 3x4V FHF.. POWER ELECTRIC Pn In TYPE Pn In In GEN..D GEN..1D GEN..1D GEN..11D PUMP PUMP kw A kw A A A A A A 1-16/18 1-16/D1 18, 32,9 1SV 8, 3,88 1,48 3 6,9 3,9 37,4 1-16/22 1-16/D16 22 39,1 1SV 9, 3,88 1,48 3 6,9 42,1 43,6 1-16/3 1-16/D18 3 3,6 1SV 11, 3,88 1,48 3 6,9 6,6 8,1 1-2/18 1-2/D168 18, 32,9 1SV 1, 3,88 1,48 3 6,9 3,9 37,4 1-2/3 1-2/D192 3 3,6 1SV 11, 3,88 1,48 3 6,9 6,6 8,1 1-2/37 1-2/D23 37 6,8 1SV 12,7 4,88 1,76 3 7,9 68,8 7,6 1-2/4 1-2/D213 4 78, 1SV 13,7 4,88 1,76 3 7,9 81, 82,8 1-2/3 1-2/D2 3 3,6 1SV 12,7 4,88 1,76 3 7,9 6,6 8,4 1-2/4 1-2/D221 4 78, 1SV 1,7 4,88 1,76 3 7,9 81, 82,8 1-2/ 1-2/D23 9, 1SV 1,7 4,88 1,76 3 7,9 98, 99,8 1-2/7 1-2/D24 7 129, 1SV 17 1,1 6,77 2,36 3 9,8 132, 134,4 1-2/9 1-2/D267 9 14, 1SV 19 1,1 6,77 2,36 3 9,8 17, 19,4 12-2/3 12-2/D18 3 3,6 1SV 9, 3,88 1,48 3 6,9 6,6 8,1 12-2/4 12-2/D26 4 78, 1SV 11, 3,88 1,48 3 6,9 81, 82, 12-2/ 12-2/D216 9, 1SV 12,7 4,88 1,76 3 7,9 98, 99,8 12-27/7 12-27/D224 7 129, 1SV 13,7 4,88 1,76 3 7,9 132, 133,8 12-27/9 12-27/D237 9 14, 1SV 1,7 4,88 1,76 3 7,9 17, 18,8 12-27/11 12-27/D23 11 188, 1SV 17 1,1 6,77 2,36 4, 11,3 192, 194,9 12-27/132 12-27/D266 132 223, 1SV 19 1,1 6,77 2,36 4, 11,3 227, 229,9 ENMTP-FHF1-en_2p_d_te (*) The current indicated is the maximum current absorbed. At the set 3x4V three-phase power supply GEN..1D and GEN..11D to add the control panel current of the engine pump (GEN..D) 1x23V The sets GEN..1D have the electric jockey pump 1x23V single-phase power supply. 4

Fire-fighting booster sets EN 1284 MARKET SECTORS CIVIL, INDUSTRIAL APPLICATIONS Fixed fire-fighting systems. Automatic Sprinkler systems. DFHF Series GEN..D/FHF SPECIFICATIONS Flow up to 6 m 3 /h. Head up to 1 m. Panel supply power voltage: 1 x 23V ± 1%. Frequency: Hz. Diesel engine with battery start. Diesel engine service pump in horizontal design: - FHF series. Maximum running pressure: 12 bar. Voltage for controls outside panel: 12-24 Vac. Protection grade: - electric panel: IP4. Electric pumps maximum power 132 kw.

DFHF 32-8 DIESEL ENGINE PUMP SERIES FIRE-FIGHTING EN 1284 GEN..D/FHF For the overall dimensions of the fuel tank and the starting batteries, see tables on pages 2-2. 6

DFHF 32-8 DIESEL ENGINE PUMP SERIES FIRE-FIGHTING EN 1284 D.. DNA DNM A B C E F H H1 H2 FHFE32-12/D119 R 2" 32 4 3 8 71 9 262 42 63 FHFE32-12/D136 R 2" 32 4 3 8 71 9 262 42 63 FHFE32-16/D1 R 2" 32 4 3 8 69 9 282 442 6 FHFE32-16/D164 R 2" 32 4 3 8 69 9 282 442 6 FHFE32-2/D188 R 2" 32 4 3 8 69 9 26 44 63 FHFE32-2/D24 R 2" 32 4 8 79 9 31 49 71 FHFE4-12/D112 6 4 4 3 8 69 9 262 42 63 FHFE4-12/D122 6 4 4 3 8 69 9 262 42 63 FHFE4-12/D143 6 4 4 3 8 69 9 262 42 63 FHFE4-16/D19 6 4 4 3 8 69 9 282 442 6 FHFE4-16/D171 6 4 4 3 8 69 9 282 442 6 FHFE4-2/D19 6 4 4 1 77 9 31 49 71 FHFE4-2/D29 6 4 4 1 77 9 31 49 72 FHFE4-2/D218 6 4 3 48 1 82 1 28 69 FHFE4-2/D233 6 4 3 48 1 92 12 33 8 FHFE4-2/D21 6 4 3 48 1 92 12 33 8 FHFE-12/D119 6 4 3 1 69 9 282 442 6 FHFE-12/D13 6 4 3 1 69 9 282 442 6 FHFE-12/D139 6 4 1 74 9 282 442 6 FHFE-16/D18 6 4 1 77 9 31 49 71 FHFE-16/D174 6 4 1 77 9 31 49 72 FHFE-2/D197 6 3 48 1 82 1 31 1 72 FHFE-2/D29 6 3 48 1 87 12 36 6 83 FHFE-2/D224 6 3 48 1 92 12 33 8 FHFE-2/D237 6 3 48 1 97 13 38 6 8 FHFE-2/D2 6 3 48 1 97 13 38 6 9 FHFE6-12/D121 8 6 4 1 72 9 31 49 71 FHFE6-12/D129 8 6 4 1 7 9 31 49 71 FHFE6-12/D14 8 6 4 1 7 1 31 49 72 FHFE6-16/D161 8 6 3 48 1 82 1 31 1 72 FHFE6-16/D168 8 6 3 48 1 92 12 36 6 83 FHFE6-16/D178 8 6 3 48 1 92 12 36 6 83 FHFE6-2/D187 8 6 3 48 1 92 12 33 8 FHFE6-2/D198 8 6 3 48 1 97 13 38 6 8 FHFE6-2/D21 8 6 3 48 1 97 13 38 6 8 FHFE6-2/D22 8 6 3 48 1 9 14 36 61 88 FHFE6-2/D241 8 6 64 9 1 113 1 36 61 1 FHFE6-2/D28 8 6 64 9 1 113 1 36 61 11 FHFE8-16/D163 1 8 3 48 12 92 12 33 8 FHFE8-16/D173 1 8 3 48 12 97 13 38 6 8 FHFE8-2/D189 1 8 3 48 12 97 14 38 63 9 FHFE8-2/D27 1 8 64 9 12 19 1 36 61 1 FHFE8-2/D22 1 8 64 9 12 113 1 36 64 11 FHFE8-2/D238 1 8 64 9 12 118 1 36 64 13 FHFE8-2/D26 1 8 66 61 12 124 17 39 67 18 Dimensions in mm. Tolerance ± 1 mm. d_fhfe-en_h_td GEN..D/FHF 7

DFHF 1-12 DIESEL ENGINE PUMP SERIES FIRE-FIGHTING EN 1284 GEN..D/FHF For the overall dimensions of the fuel tank and the starting batteries, see tables on pages 2-2. D.. DNA DNM A B C E F H H1 H2 FHFE1-16/D1 12 1 3 48 12 1 13 348 628 87 FHFE1-16/D16 12 1 3 48 12 96 14 398 678 87 FHFE1-16/D18 12 1 64 9 12 11 1 348 628 99 FHFE1-2/D168 12 1 3 48 12 1 14 373 63 8 FHFE1-2/D192 12 1 64 9 12 11 1 373 63 11 FHFE1-2/D23 12 1 64 9 12 12 1 373 63 1 FHFE1-2/D213 12 1 64 9 12 114 1 368 648 11 FHFE1-2/D2 12 1 64 9 14 12 16 348 628 99 FHFE1-2/D221 12 1 64 9 14 12 16 348 628 1 FHFE1-2/D23 12 1 64 9 14 119 17 393 673 18 FHFE1-2/D24 12 1 7 6 14 13 2 373 63 14 FHFE1-2/D267 12 1 7 6 14 13 2 373 63 14 FHFE12-2/D18 1 12 64 9 14 12 16 373 688 11 FHFE12-2/D26 1 12 64 9 14 119 16 343 68 1 FHFE12-2/D216 1 12 64 9 14 119 18 393 78 18 FHFE12-27/D224 1 12 7 6 14 13 21 423 778 19 FHFE12-27/D237 1 12 7 6 14 13 21 423 778 11 FHFE12-27/D23 1 12 8 7 14 13 2 478 833 13 FHFE12-27/D266 1 12 8 7 14 13 2 478 833 13 Dimensions in mm. Tolerance ± 1 mm. d_fhfe1-en_e_td 8

Fire-fighting booster sets EN 1284 MARKET SECTORS CIVIL, INDUSTRIAL APPLICATIONS Fixed fire-fighting systems. Automatic Sprinkler systems. GEN..D/FHF Series GEN..D/FHF SPECIFICATIONS Flow up to 6 m 3 /h. Head up to 1 m. Panel supply power voltage: 1 x 23V ± 1%. Frequency: Hz. Voltage for controls outside panel: 12-24 Vac. Diesel engine with battery start. Diesel engine service pump in horizontal design: - FHF series. Maximum running pressure: 12 bar. Protection grade: - electric panel: IP4. Electric pumps maximum power 132 kw. 9

GEN..D/FHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..D/FHF For the overall dimensions of the fuel tank and the starting batteries, see tables on pages 2-2. 6

GEN..D/FHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..D DRW N DNA DNM A B D E G N P Q FHF32-12/D119 1 R 2" R 1"1/2 4 3 8 71 262 9 913 1487 FHF32-12/D136 1 R 2" R 1"1/2 4 3 8 71 262 9 913 1487 FHF32-16/D1 1 R 2" R 1"1/2 4 3 8 69 282 9 93 127 FHF32-16/D164 1 R 2" R 1"1/2 4 3 8 69 282 9 93 127 FHF32-2/D188 1 R 2" R 1"1/2 4 3 8 69 26 9 91 12 FHF32-2/D24 1 R 2" R 1"1/2 4 8 79 31 9 11 17 FHF4-12/D112 2 6 6 4 3 8 69 262 9 119 1697 FHF4-12/D122 2 6 6 4 3 8 69 262 9 119 1697 FHF4-12/D143 2 6 6 4 3 8 69 262 9 119 1697 FHF4-16/D19 2 6 6 4 3 8 69 282 9 1149 1737 FHF4-16/D171 2 6 6 4 3 8 69 282 9 1149 1737 FHF4-2/D19 2 6 6 4 1 77 31 9 1197 178 FHF4-2/D29 2 6 6 4 1 77 31 9 1197 178 FHF4-2/D218 2 6 6 3 48 1 82 28 1 1212 18 FHF4-2/D233 2 6 6 3 48 1 92 33 12 1262 18 FHF4-2/D21 2 6 6 3 48 1 92 33 12 1262 18 FHF-12/D119 2 6 6 4 3 1 69 282 9 1241 1829 FHF-12/D13 2 6 6 4 3 1 69 282 9 1241 1829 FHF-12/D139 2 6 6 4 1 74 282 9 1241 1829 FHF-16/D18 2 6 6 4 1 77 31 9 1289 1877 FHF-16/D174 2 6 6 4 1 77 31 9 1289 1877 FHF-2/D197 2 6 6 3 48 1 82 31 1 139 1897 FHF-2/D29 2 6 6 3 48 1 87 36 12 139 1947 FHF-2/D224 2 6 6 3 48 1 92 33 12 134 1942 FHF-2/D237 2 6 6 3 48 1 97 38 13 144 1992 FHF-2/D2 2 6 6 3 48 1 97 38 13 144 1992 FHF6-12/D121 2 8 8 4 1 72 31 9 136 19 FHF6-12/D129 2 8 8 4 1 7 31 9 136 19 FHF6-12/D14 2 8 8 4 1 7 31 1 136 19 FHF6-16/D161 2 8 8 3 48 1 82 31 1 1376 197 FHF6-16/D168 2 8 8 3 48 1 92 36 12 1426 22 FHF6-16/D178 2 8 8 3 48 1 92 36 12 1426 22 FHF6-2/D187 2 8 8 3 48 1 92 33 12 1421 21 FHF6-2/D198 2 8 8 3 48 1 97 38 13 1471 26 FHF6-2/D21 2 8 8 3 48 1 97 38 13 1471 26 FHF6-2/D22 2 8 8 3 48 1 9 36 14 1476 27 FHF6-2/D241 2 8 8 64 9 1 113 36 1 1476 27 FHF6-2/D28 2 8 8 64 9 1 113 36 1 1476 27 FHF8-16/D163 2 1 1 3 48 12 92 33 12 14 2111 FHF8-16/D173 2 1 1 3 48 12 97 38 13 14 2161 FHF8-2/D189 2 1 1 3 48 12 97 38 14 179 2186 FHF8-2/D27 2 1 1 64 9 12 19 36 1 19 2166 FHF8-2/D22 2 1 1 64 9 12 113 36 1 189 2196 FHF8-2/D238 2 1 1 64 9 12 118 36 1 194 221 FHF8-2/D26 2 1 1 66 61 12 124 39 17 1619 2226 Dimensions in mm. Tolerance ± 1 mm. gend_fhf-en_h_td GEN..D/FHF 61

GEN..D/FHF 1-12 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..D/FHF For the overall dimensions of the fuel tank and the starting batteries, see tables on pages 2-2. GEN..D DRW N DNA DNM A B D E G N P Q FHF1-16/D1 2 12 12 3 48 12 1 348 13 1676 2296 FHF1-16/D16 2 12 12 3 48 12 96 398 14 1726 2346 FHF1-16/D18 2 12 12 64 9 12 11 348 1 1676 2296 FHF1-2/D168 2 12 12 3 48 12 1 373 14 171 2321 FHF1-2/D192 2 12 12 64 9 12 11 373 1 171 2321 FHF1-2/D23 2 12 12 64 9 12 12 373 1 171 2321 FHF1-2/D213 2 12 12 64 9 12 114 368 1 1696 2316 FHF1-2/D2 2 12 12 64 9 14 12 348 16 1676 2296 FHF1-2/D221 2 12 12 64 9 14 12 348 16 1676 2296 FHF1-2/D23 2 12 12 64 9 14 119 393 17 1721 2341 FHF1-2/D24 2 12 12 7 6 14 13 373 2 171 2321 FHF1-2/D267 2 12 12 7 6 14 13 373 2 171 2321 FHF12-2/D18 2 1 1 64 9 14 12 373 16 1868 22 FHF12-2/D26 2 1 1 64 9 14 119 343 16 1838 2472 FHF12-2/D216 2 1 1 64 9 14 119 393 18 1888 222 FHF12-27/D224 2 1 1 7 6 14 13 423 21 198 292 FHF12-27/D237 2 1 1 7 6 14 13 423 21 198 292 FHF12-27/D23 2 1 1 8 7 14 13 478 2 213 2647 FHF12-27/D266 2 1 1 8 7 14 13 478 2 213 2647 Dimensions in mm. Tolerance ± 1 mm. gend_fhf1-en_f_td 62

Fire-fighting booster sets EN 1284 MARKET SECTORS CIVIL, INDUSTRIAL APPLICATIONS Fixed fire-fighting systems. Automatic Sprinkler systems. GEN..1D/FHF Series GEN..D/FHF SPECIFICATIONS Flow up to 6 m 3 /h. Head up to 1 m. Panel supply power voltage: - Electric pump: 1 x 23V ± 1%. - Diesel engine pump: 1 x 23V ± 1%. Frequency: Hz. Voltage for controls outside panel: 12-24 Vac. Protection grade: - electric panel: IP4. Electric pumps maximum power 132 kw. Electric motor start : - Direct start for powers up to 22 kw included for electric pump. Diesel engine with battery start. Service pump in horizontal design: - FHF series. Electric jockey pump with vertical axis: - SV Series (motor protection grade IP). Maximum running pressure: 12 bar. 63

GEN..1D/FHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..D/FHF For the overall dimensions of the fuel tank and the starting batteries, see tables on pages 2-2. 64

GEN..1D/FHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..1D DRW N DNA DNP DNM A A1 B C D F G H I L N P Q FHF32-12/D119 1 R 2" Rp 1" R 1"1/2 33 22 28 9 8 22 362 14 4 9 126 113 187 FHF32-12/D136 1 R 2" Rp 1" R 1"1/2 33 22 28 9 8 22 362 14 4 9 126 113 187 FHF32-16/D1 1 R 2" Rp 1" R 1"1/2 33 22 28 88 8 22 382 14 4 9 124 13 1627 FHF32-16/D164 1 R 2" Rp 1" R 1"1/2 33 22 28 88 8 22 382 14 4 9 124 13 1627 FHF32-2/D188 1 R 2" Rp 1" R 1"1/2 33 22 28 88 8 22 36 14 4 9 124 11 162 FHF32-2/D24 1 R 2" Rp 1" R 1"1/2 4 22 28 1 8 22 41 14 47 11 136 111 167 FHF4-12/D112 2 6 Rp 1" 6 33 22 28 88 8 22 362 14 4 9 124 126 1794 FHF4-12/D122 2 6 Rp 1" 6 33 22 28 88 8 22 362 14 4 9 124 126 1794 FHF4-12/D143 2 6 Rp 1" 6 33 22 28 88 8 22 362 14 4 9 124 126 1794 FHF4-16/D19 2 6 Rp 1" 6 33 22 28 88 8 22 382 14 4 9 124 1246 1834 FHF4-16/D171 2 6 Rp 1" 6 33 22 28 88 8 22 382 14 4 9 124 1246 1834 FHF4-2/D19 2 6 Rp 1" 6 4 22 28 98 1 22 41 14 47 11 136 1294 1882 FHF4-2/D29 2 6 Rp 1" 6 4 22 28 98 1 22 41 14 47 11 136 1294 1882 FHF4-2/D218 2 6 Rp 1" 6 39 23 28 97 1 22 38 14 47 11 13 139 1897 FHF4-2/D233 2 6 Rp 1" 6 39 23 28 117 1 22 43 14 47 11 1 139 1947 FHF4-2/D21 2 6 Rp 1" 6 39 23 28 117 1 22 43 14 47 11 1 139 1947 FHF-12/D119 2 6 Rp 1" 6 33 22 28 88 1 22 382 14 4 9 126 1338 1926 FHF-12/D13 2 6 Rp 1" 6 33 22 28 88 1 22 382 14 4 9 126 1338 1926 FHF-12/D139 2 6 Rp 1" 6 4 22 28 9 1 22 382 14 47 11 133 1338 1926 FHF-16/D18 2 6 Rp 1" 6 4 22 28 98 1 22 41 14 47 11 136 1386 1974 FHF-16/D174 2 6 Rp 1" 6 4 22 28 98 1 22 41 14 47 11 136 1386 1974 FHF-2/D197 2 6 Rp 1" 6 39 23 28 97 1 22 41 14 47 11 13 146 1994 FHF-2/D29 2 6 Rp 1" 6 39 23 28 112 1 22 46 14 47 11 1 146 244 FHF-2/D224 2 6 Rp 1" 6 39 23 28 117 1 22 43 14 47 11 1 141 239 FHF-2/D237 2 6 Rp 1" 6 39 23 28 122 1 22 48 1 47 11 16 11 289 FHF-2/D2 2 6 Rp 1" 6 39 23 28 122 1 22 48 1 47 11 16 11 289 FHF6-12/D121 2 8 Rp 1" 8 4 22 28 94 1 22 41 14 47 11 132 143 247 FHF6-12/D129 2 8 Rp 1" 8 4 22 28 97 1 22 41 14 47 11 13 143 247 FHF6-12/D14 2 8 Rp 1" 8 4 22 28 97 1 22 41 14 47 11 13 143 247 FHF6-16/D161 2 8 Rp 1" 8 39 23 28 97 1 22 41 14 47 11 13 1473 267 FHF6-16/D168 2 8 Rp 1" 8 39 23 28 117 1 22 46 14 47 11 1 123 2117 FHF6-16/D178 2 8 Rp 1" 8 39 23 28 117 1 22 46 14 47 11 1 123 2117 FHF6-2/D187 2 8 Rp 1" 8 39 23 28 117 1 22 43 14 47 11 1 118 2112 FHF6-2/D198 2 8 Rp 1" 8 39 23 28 122 1 22 48 1 47 11 16 168 2162 FHF6-2/D21 2 8 Rp 1" 8 39 23 28 122 1 22 48 1 47 11 16 168 2162 FHF6-2/D22 2 8 Rp 1" 8 39 23 28 13 1 22 46 1 47 11 168 173 2167 FHF6-2/D241 2 8 Rp 1" 8 46 38 18 127 1 24 48 17 3 137 1 193 2187 FHF6-2/D28 2 8 Rp 1" 8 46 38 18 127 1 24 48 17 3 137 1 193 2187 FHF8-16/D163 2 1 Rp 1" 1 39 23 28 117 12 22 43 14 47 11 17 161 228 FHF8-16/D173 2 1 Rp 1" 1 39 23 28 122 12 22 48 1 47 11 162 161 228 FHF8-2/D189 2 1 Rp 1" 1 39 23 28 137 12 22 48 1 47 11 177 1676 2283 FHF8-2/D27 2 1 Rp 1" 1 27 28 144 12 24 48 17 3 13 184 1676 2283 FHF8-2/D22 2 1 Rp 1" 1 46 38 1 127 12 24 48 17 3 137 1 176 2313 FHF8-2/D238 2 1 Rp 1" 1 26 28 1 12 24 48 194 3 13 19 1711 2318 FHF8-2/D26 2 1 Rp 1" 1 26 24 138 12 26 3 196 3 13 17 176 2363 Dimensions in mm. Tolerance ± 1 mm. gen1d_fhf-en_g_td GEN..D/FHF 6

GEN..1D/FHF 1-12 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..D/FHF For the overall dimensions of the fuel tank and the starting batteries, see tables on pages 2-2. 66

GEN..1D/FHF 1-12 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..1D DRW N DNA DNP DNM A A1 B C D F G H I L N P Q FHF1-16/D1 2 12 Rp 1" 12 39 23 28 13 12 22 448 1 47 11 17 1773 2393 FHF1-16/D16 2 12 Rp 1" 12 39 23 28 136 12 22 498 1 47 11 176 1823 2443 FHF1-16/D18 2 12 Rp 1" 12 46 38 13 129 12 24 468 17 3 137 1 1793 2413 FHF1-2/D168 2 12 Rp 1" 12 39 23 28 13 12 22 473 1 47 11 17 1798 2418 FHF1-2/D192 2 12 Rp 1" 12 46 38 13 129 12 24 493 17 3 137 1 1818 2438 FHF1-2/D23 2 12 Rp 1" 12 27 28 14 12 24 493 17 3 13 19 1818 2438 FHF1-2/D213 2 12 Rp 1" 12 27 28 148 12 24 488 17 3 13 189 1813 2433 FHF1-2/D2 2 12 Rp 1" 12 27 28 14 14 24 468 17 3 13 196 1793 2413 FHF1-2/D221 2 12 Rp 1" 12 27 28 14 14 24 468 17 3 13 196 1793 2413 FHF1-2/D23 2 12 Rp 1" 12 26 28 166 14 24 13 17 3 13 28 1838 248 FHF1-2/D24 3 12 Rp 1" 12 26 7 134 14 21 13 \ 7 138 2 1838 248 FHF1-2/D267 3 12 Rp 1" 12 26 7 134 14 21 13 \ 7 138 2 1838 248 FHF12-2/D18 2 1 Rp 1" 1 27 28 14 14 24 493 17 3 13 196 198 2619 FHF12-2/D26 2 1 Rp 1" 1 26 28 16 14 24 463 17 3 13 198 19 289 FHF12-2/D216 2 1 Rp 1" 1 26 28 171 14 24 13 194 3 13 213 2 2639 FHF12-27/D224 3 1 Rp 1" 1 26 62 134 14 22 63 \ 7 138 21 29 2729 FHF12-27/D237 3 1 Rp 1" 1 26 62 134 14 22 63 \ 7 138 21 29 2729 FHF12-27/D23 3 1 Rp 1" 1 6 26 7 134 14 22 618 \ 62 148 2 21 2784 FHF12-27/D266 3 1 Rp 1" 1 6 26 7 134 14 22 618 \ 62 148 2 21 2784 Dimensions in mm. Tolerance ± 1 mm. gen1d_fhf1-en_f_td GEN..D/FHF 67

GEN..D/FHF 68

Fire-fighting booster sets EN 1284 MARKET SECTORS CIVIL, INDUSTRIAL APPLICATIONS Fixed fire-fighting systems. Automatic Sprinkler systems. GEN..1D/FHF Series GEN..D/FHF SPECIFICATIONS Flow up to 13 m 3 /h. Head up to 1 m. Panel supply power voltage: - Electric pump: 3 x 4V ± 1%. - Diesel engine pump: 1 x 23V ± 1%. Frequency: Hz. Voltage for controls outside panel: 12-24 Vac. Protection grade: - electric panel: IP4. Electric motor start : - Direct start for powers up to 22 kw included for pump (GEND...). - Star/delta start for higher powers (GENY... set). Diesel engine with battery start. Service pump in horizontal design: - FHF series (IP electric motor protection). Maximum running pressure: 12 bar. Electric pumps maximum power 132 kw. 69

GEN..1D/FHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..D/FHF For the overall dimensions of the fuel tank and the starting batteries, see tables on pages 2-2. 7

GEN..1D/FHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..1D DRW N DNA DNM A A1 B C D G H I L N P Q FHF32-12/7/D119 1 R 2" R 2" 32 31 24 87 8 362 14 47 11 119 119 199 FHF32-12/11/D136 1 R 2" R 2" 32 31 24 87 8 362 14 47 11 119 119 199 FHF32-16/1/D1 1 R 2" R 2" 32 31 24 8 8 382 14 47 11 117 19 1639 FHF32-16/22/D164 1 R 2" R 2" 32 31 24 8 8 382 14 47 11 117 19 1639 FHF32-2/3/D188 1 R 2" R 2" 32 31 24 8 8 36 14 47 11 117 17 1637 FHF32-2/4/D24 1 R 2" R 2" 38 3 24 96 8 41 14 7 13 128 117 1687 FHF4-12/11/D112 2 6 6 32 31 24 8 8 362 14 47 11 117 126 1794 FHF4-12/1/D122 2 6 6 32 31 24 8 8 362 14 47 11 117 126 1794 FHF4-12/22/D143 2 6 6 32 31 24 8 8 362 14 47 11 117 126 1794 FHF4-16/3/D19 2 6 6 32 31 24 8 8 382 14 47 11 117 1246 1834 FHF4-16/4/D171 2 6 6 32 31 24 8 8 382 14 47 11 117 1246 1834 FHF4-2//D19 2 6 6 38 3 24 94 1 41 14 7 13 128 1294 1882 FHF4-2/7/D29 2 6 6 38 3 24 94 1 41 14 7 13 128 1294 1882 FHF4-2/11A/D218 2 6 6 42 37 18 114 1 38 14 61 14 142 139 1897 FHF4-2/11/D233 2 6 6 42 37 28 122 1 43 14 61 14 16 139 1947 FHF4-2/1/D21 2 6 6 42 37 28 122 1 43 14 61 14 16 139 1947 FHF-12/22/D119 2 6 8 32 31 24 8 1 382 14 47 11 119 134 1939 FHF-12/3/D13 2 6 8 32 31 24 8 1 382 14 47 11 119 134 1939 FHF-12/4/D139 2 6 8 38 3 24 91 1 382 14 7 13 12 134 1939 FHF-16//D18 2 6 8 38 3 24 94 1 41 14 7 13 128 1393 1987 FHF-16/7/D174 2 6 8 38 3 24 94 1 41 14 7 13 128 1393 1987 FHF-2/11A/D197 2 6 8 42 37 11 18 1 41 14 61 14 129 1413 27 FHF-2/11/D29 2 6 8 42 37 11 18 1 46 14 61 14 129 1463 27 FHF-2/1/D224 2 6 8 42 37 28 122 1 43 14 61 14 16 148 22 FHF-2/18/D237 2 6 8 42 37 28 127 1 48 1 61 14 16 18 212 FHF-2/22/D2 2 6 8 42 37 28 127 1 48 1 61 14 16 18 212 FHF6-12/4/D121 2 8 1 38 3 24 89 1 41 14 7 13 123 146 272 FHF6-12//D129 2 8 1 38 3 24 92 1 41 14 7 13 126 146 272 FHF6-12/7/D14 2 8 1 38 3 24 92 1 41 14 7 13 126 146 272 FHF6-16/11A/D161 2 8 1 42 37 18 114 1 41 14 61 14 142 148 292 FHF6-16/11/D168 2 8 1 42 37 28 122 1 46 14 61 14 16 13 2142 FHF6-16/1/D178 2 8 1 42 37 28 122 1 46 14 61 14 16 13 2142 FHF6-2/1/D187 2 8 1 42 37 28 122 1 43 14 61 14 16 13 2137 FHF6-2/18/D198 2 8 1 42 37 28 127 1 48 1 61 14 16 18 2187 FHF6-2/22/D21 2 8 1 42 37 28 127 1 48 1 61 14 16 18 2187 FHF6-2/22/D22 2 8 1 42 37 28 126 1 46 1 61 14 164 18 2192 FHF6-2/3/D241 2 8 1 48 4 28 14 1 48 17 73 166 183 16 2212 FHF6-2/37/D28 2 8 1 48 4 28 14 1 48 17 73 166 183 16 2212 FHF8-16/1/D163 2 1 12 42 37 28 122 12 43 14 61 14 163 1614 2234 FHF8-16/18/D173 2 1 12 42 37 28 127 12 48 1 61 14 168 1664 2284 FHF8-2/22/D189 2 1 12 42 37 28 127 12 48 1 61 14 168 1689 239 FHF8-2/3/D27 2 1 12 48 4 28 141 12 48 17 73 166 182 1689 239 FHF8-2/37/D22 2 1 12 48 4 28 14 12 48 17 73 166 18 1719 2339 FHF8-2/4/D238 2 1 12 48 4 32 14 12 48 194 73 166 189 1724 2344 FHF8-2//D26 2 1 12 48 4 32 1 12 3 196 73 166 19 1769 2389 Dimensions in mm. Tolerance ± 1 mm. gen1d_fhf-en_g_td GEN..D/FHF 71

GEN..D/FHF 72

Fire-fighting booster sets EN 1284 MARKET SECTORS CIVIL, INDUSTRIAL APPLICATIONS Fixed fire-fighting systems. Automatic Sprinkler systems. GEN..11D/FHF Series GEN..D/FHF SPECIFICATIONS Flow up to 13 m 3 /h. Head up to 1 m. Panel supply power voltage: - Electric pump: 3 x 4V ± 1%. - Diesel engine pump: 1 x 23V ± 1%. Frequency: Hz. Voltage for controls outside panel: 12-24 Vac. Protection grade: - electric panel: IP4. Electric pumps maximum power 132 kw. Electric motor start : - Direct start for powers up to 22 kw included for pump (GEND...). - Star/delta start for higher powers (GENY... set). Diesel engine with battery start. Service pump in horizontal design: - FHF series (IP electric motor protection). Electric jockey pump with vertical axis: - SV Series (motor protection grade IP). Maximum running pressure: 12 bar. 73

GEN..11D/FHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..D/FHF For the overall dimensions of the fuel tank and the starting batteries, see tables on pages 2-2. 74

GEN..11D/FHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..11D DRW DNA DNP DNM A A1 B C D F G H I I1 L N P Q N FHF32-12/7/D119 1 R 2" Rp 1" R 2" 3 29 24 9 8 22 362 14 4 4 14 122 119 199 FHF32-12/11/D136 1 R 2" Rp 1" R 2" 3 29 24 9 8 22 362 14 4 4 14 122 119 199 FHF32-16/1/D1 1 R 2" Rp 1" R 2" 3 29 24 8 8 22 382 14 4 4 14 117 19 1639 FHF32-16/22/D164 1 R 2" Rp 1" R 2" 3 29 24 8 8 22 382 14 4 4 14 117 19 1639 FHF32-2/3/D188 1 R 2" Rp 1" R 2" 3 29 24 8 8 22 36 14 4 4 14 117 17 1637 FHF32-2/4/D24 1 R 2" Rp 1" R 2" 4 37 24 1 8 22 41 14 47 43 168 132 117 1687 FHF4-12/11/D112 2 6 Rp 1" 6 3 29 24 8 8 22 362 14 4 4 14 117 126 1794 FHF4-12/1/D122 2 6 Rp 1" 6 3 29 24 8 8 22 362 14 4 4 14 117 126 1794 FHF4-12/22/D143 2 6 Rp 1" 6 3 29 24 8 8 22 362 14 4 4 14 117 126 1794 FHF4-16/3/D19 2 6 Rp 1" 6 3 29 24 8 8 22 382 14 4 4 14 117 1246 1834 FHF4-16/4/D171 2 6 Rp 1" 6 3 29 24 8 8 22 382 14 4 4 14 117 1246 1834 FHF4-2//D19 2 6 Rp 1" 6 4 37 24 94 1 22 41 14 47 43 168 128 1294 1882 FHF4-2/7/D29 2 6 Rp 1" 6 4 37 24 94 1 22 41 14 47 43 168 128 1294 1882 FHF4-2/11A/D218 2 6 Rp 1" 6 36 3 18 99 1 22 38 14 47 47 167 127 139 1897 FHF4-2/11/D233 2 6 Rp 1" 6 37 38 28 99 1 22 43 14 47 47 171 137 139 1947 FHF4-2/1/D21 2 6 Rp 1" 6 37 38 28 99 1 22 43 14 47 47 171 137 139 1947 FHF-12/22/D119 2 6 Rp 1" 8 3 29 24 8 1 22 382 14 4 4 14 119 134 1939 FHF-12/3/D13 2 6 Rp 1" 8 3 29 24 8 1 22 382 14 4 4 14 119 134 1939 FHF-12/4/D139 2 6 Rp 1" 8 4 37 24 1 1 22 382 14 47 43 168 134 134 1939 FHF-16//D18 2 6 Rp 1" 8 4 37 24 94 1 22 41 14 47 43 168 128 1393 1987 FHF-16/7/D174 2 6 Rp 1" 8 4 37 24 94 1 22 41 14 47 43 168 128 1393 1987 FHF-2/11A/D197 2 6 Rp 1" 8 38 34 11 89 1 22 41 14 47 47 168 11 1413 27 FHF-2/11/D29 2 6 Rp 1" 8 38 34 2 89 1 22 46 14 47 47 168 12 1463 27 FHF-2/1/D224 2 6 Rp 1" 8 37 38 28 99 1 22 43 14 47 47 171 137 148 22 FHF-2/18/D237 2 6 Rp 1" 8 4 39 28 99 1 22 48 1 47 47 174 137 18 212 FHF-2/22/D2 2 6 Rp 1" 8 4 39 28 99 1 22 48 1 47 47 174 137 18 212 FHF6-12/4/D121 2 8 Rp 1" 1 4 37 24 89 1 22 41 14 47 43 168 123 146 272 FHF6-12//D129 2 8 Rp 1" 1 4 37 24 92 1 22 41 14 47 43 168 126 146 272 FHF6-12/7/D14 2 8 Rp 1" 1 4 37 24 92 1 22 41 14 47 43 168 126 146 272 FHF6-16/11A/D161 2 8 Rp 1" 1 36 3 18 99 1 22 41 14 47 47 167 127 148 292 FHF6-16/11/D168 2 8 Rp 1" 1 37 38 28 99 1 22 46 14 47 47 171 137 13 2142 FHF6-16/1/D178 2 8 Rp 1" 1 37 38 28 99 1 22 46 14 47 47 171 137 13 2142 FHF6-2/1/D187 2 8 Rp 1" 1 37 38 28 99 1 22 43 14 47 47 171 137 13 2137 FHF6-2/18/D198 2 8 Rp 1" 1 4 39 28 99 1 22 48 1 47 47 174 137 18 2187 FHF6-2/22/D21 2 8 Rp 1" 1 4 39 28 99 1 22 48 1 47 47 174 137 18 2187 FHF6-2/22/D22 2 8 Rp 1" 1 4 39 37 98 1 22 46 1 47 47 174 14 18 2192 FHF6-2/3/D241 2 8 Rp 1" 1 47 43 29 116 1 19 48 17 3 49 192 1 16 2212 FHF6-2/37/D28 2 8 Rp 1" 1 47 43 29 116 1 19 48 17 3 49 192 1 16 2212 FHF8-16/1/D163 2 1 Rp 1" 12 37 38 28 99 12 22 43 14 47 47 171 14 1614 2234 FHF8-16/18/D173 2 1 Rp 1" 12 4 39 28 99 12 22 48 1 47 47 174 14 1664 2284 FHF8-2/22/D189 2 1 Rp 1" 12 4 39 33 99 12 22 48 1 47 47 174 14 1689 239 FHF8-2/3/D27 2 1 Rp 1" 12 47 43 3 112 12 19 48 17 3 49 192 1 1689 239 FHF8-2/37/D22 2 1 Rp 1" 12 47 43 28 116 12 19 48 17 3 49 192 16 1719 2339 FHF8-2/4/D238 2 1 Rp 1" 12 47 39 32 12 12 19 48 194 3 49 188 16 1724 2344 FHF8-2//D26 2 1 Rp 1" 12 48 4 3 127 12 21 3 196 3 3 2 17 1769 2389 Dimensions in mm. Tolerance ± 1 mm. gen11d_fhf-en_g_td GEN..D/FHF 7

GEN..11D/FHF 1-12 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..D/FHF For the overall dimensions of the fuel tank and the starting batteries, see tables on pages 2-2. 76

GEN..11D/FHF 1-12 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..11D DRW DNA DNP DNM A A1 B C D F G H I I1 L N P Q N FHF1-16/18/D1 2 12 Rp 1" 1 4 39 26 12 12 22 448 1 47 47 174 141 1787 2421 FHF1-16/22/D16 2 12 Rp 1" 1 4 39 34 98 12 22 498 1 47 47 174 14 1837 2471 FHF1-16/3/D18 2 12 Rp 1" 2 47 39 28 117 12 19 468 17 3 49 188 18 1833 2492 FHF1-2/18/D168 2 12 Rp 1" 1 4 39 3 12 12 22 473 1 47 47 174 14 1812 2446 FHF1-2/3/D192 2 12 Rp 1" 1 47 39 26 117 12 19 493 17 3 49 188 16 1832 2466 FHF1-2/37/D23 2 12 Rp 1" 1 47 39 28 122 12 19 493 17 3 49 188 163 1832 2466 FHF1-2/4/D213 2 12 Rp 1" 2 4 46 32 14 12 19 488 17 3 3 197 18 183 212 FHF1-2/3/D2 2 12 Rp 1" 1 47 39 32 122 14 19 468 17 3 49 188 168 187 2441 FHF1-2/4/D221 2 12 Rp 1" 2 47 39 32 122 14 19 468 17 3 49 188 168 1833 2492 FHF1-2//D23 2 12 Rp 1" 2 4 46 32 14 14 19 13 17 3 3 197 186 1878 237 FHF1-2/7/D24 3 12 Rp 1" 2 4 7 134 14 21 13 \ 7 7 223 2 1878 237 FHF1-2/9/D267 3 12 Rp 1" 2 4 7 134 14 21 13 \ 7 7 223 2 1878 237 FHF12-2/3/D18 2 1 Rp 1" 2 47 39 36 11 14 2 493 17 3 49 188 16 211 267 FHF12-2/4/D26 2 1 Rp 1" 2 4 46 32 14 14 2 463 17 3 3 197 186 1981 264 FHF12-2//D216 2 1 Rp 1" 2 4 46 32 14 14 2 13 194 3 3 197 186 231 269 FHF12-27/7/D223 3 1 Rp 1" 2 4 141 14 22 63 \ 7 7 224 21 2148 2834 FHF12-27/9/D237 3 1 Rp 1" 2 62 134 14 22 63 \ 7 7 224 21 2148 2834 FHF12-27/11/D23 3 1 Rp 1" 2 6 61 642 134 14 22 618 \ 62 64 247 2122 223 2889 FHF12-27/132/D266 3 1 Rp 1" 2 6 61 642 134 14 22 618 \ 62 64 247 2122 223 2889 Dimensions in mm. Tolerance ± 1 mm. gen11d_fhf1-en_f_td GEN..D/FHF 77

GEN..D/FHF 78

GEN..D/FHF SERIES OF BOOSTER SETS (POSITIVE SUCTION HEAD) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT FH 32-12 29 [rpm] ISO 996 - Annex A FH 32-16 29 [rpm] ISO 996 - Annex A 2 4 6 8 1 Q [Imp gpm] 2 4 6 8 Q 1 [Imp gpm] 2 4 6 8 1 12 Q [US gpm],2,8 Hc [m] H [ft],2,6 2 4 6 8 1 12 Q [US gpm],2,8 Hc [m] H [ft],2,6,1,1,4,1,1,4,,2,,2, 6,, 1, 3 NPSHr [m] 4 2 1 1 NPSHr [ft] NPSHr [m] 8 6 4 2 2 2 1 1 NPSHr [ft] GEN..D/FHF 1 1 2 2 Q [m 3 /h] 3 1 2 3 4 Q [l/min] 76474_A_CH 1 1 2 2 Q [m 3 /h] 3 1 2 3 4 Q [l/min] 7647_A_CH FH 32-2 29 [rpm] ISO 996 - Annex A FH 4-12 29 [rpm] ISO 996 - Annex A 2 4 6 8 1 Q 12 [Imp gpm] 1 1 2 Q [Imp gpm] 2 4 6 8 1 12 14 Q [US gpm], 1 1 2 Q [US 2gpm], Hc [m],4 1, H [ft] Hc [m],4 1, H [ft],3 1,,3 1,,2,2,,,1,1, 1,, 1, 3 8 2 4 6 2 1 3 NPSHr [m] 4 1 NPSHr [ft] NPSHr [m] 2 NPSHr [ft] 1 2 1 1 1 2 2 3 Q [m 3 /h] 3 1 2 3 4 Q [l/min] 76476_A_CH 1 2 3 4 Q [m 3 /h] 6 2 4 6 8 Q 1 [l/min] 76477_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 79

GEN..D/FHF SERIES OF BOOSTER SETS (POSITIVE SUCTION HEAD) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT FH 4-16 29 [rpm] ISO 996 - Annex A FH 4-2 29 [rpm] ISO 996 - Annex A 1 1 2 Q [Imp gpm] 1 1 2 Q [Imp gpm] 1 1 2 Q [US 2gpm], 1 1 2 Q [US 2gpm],6 Hc [m],4 1, H [ft] Hc [m], 1, H [ft],3 1,,4,3 1,,2,1,,2,1,, 1,, 1, GEN..D/FHF NPSHr [m] 1 4 3 2 1 NPSHr [ft] NPSHr [m] 1 4 3 2 1 NPSHr [ft] 1 2 3 4 Q [m 3 /h] 6 2 4 6 8 Q 1 [l/min] 76478_A_CH 1 2 3 4 Q [m 3 /h] 6 2 4 6 8 Q 1 [l/min] 7646_A_CH FH 4-2 29 [rpm] ISO 996 - Annex A FH - 12 29 [rpm] ISO 996 - Annex A 1 1 2 Q [Imp gpm] 1 2 3 Q [Imp gpm] 1 1 2 Q [US 2gpm],6 1 2 3 4, Q [US gpm] Hc [m], 1, H [ft] Hc [m],4 1, H [ft],4,3 1,,3 1,,2,2,1,,1,, 1,, 1, 4 4 1 3 1 3 NPSHr [m] 2 NPSHr [ft] NPSHr [m] 2 NPSHr [ft] 1 1 1 2 3 4 Q [m 3 /h] 6 2 4 6 8 Q 1 [l/min] 7647_A_CH 2 4 6 8 Q [m 3 1 /h] 2 4 6 8 1 12 14 16 Q [l/min] 76481_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 8

GEN..D/FHF SERIES OF BOOSTER SETS (POSITIVE SUCTION HEAD) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT FH - 16 29 [rpm] ISO 996 - Annex A FH - 2 29 [rpm] ISO 996 - Annex A 1 2 3 Q [Imp gpm] 1 2 3 4 Q [Imp gpm] 1 2 3 4, Q [US gpm] 1 2 3 4 Q [US gpm], Hc [m],4 1, H [ft] Hc [m],4 1, H [ft],3 1,,3 1,,2,2,,,1,1, 1,, 1, NPSHr [m] 1 4 3 2 1 NPSHr [ft] NPSHr [m] 1 4 3 2 1 NPSHr [ft] GEN..D/FHF 2 4 6 8 Q [m1 3 /h] 2 4 6 8 1 12 14 Q 16 [l/min] 76482_A_CH 2 4 6 8 1 Q [m12 3 /h] 1 1 Q [l/min] 2 76483_A_CH FH - 2 29 [rpm] ISO 996 - Annex A FH 6-12 29 [rpm] ISO 996 - Annex A 1 2 3 4 Q [Imp gpm] 1 2 3 4 Q [Imp gpm] 1 2 3 4 Q [US gpm],6 1 2 3 4 Q [US 6 gpm],6 Hc [m], H [ft] Hc [m], H [ft] 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, 4 4 1 3 1 3 NPSHr [m] 2 NPSHr [ft] NPSHr [m] 2 NPSHr [ft] 1 1 2 4 6 8 1 Q [m12 3 /h] 1 1 Q [l/min] 2 76484_A_CH 2 4 6 8 1 12 Q [m14 3 /h] 1 1 2 Q [l/min] 7648_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 81

GEN..D/FHF SERIES OF BOOSTER SETS (POSITIVE SUCTION HEAD) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT FH 6-16 29 [rpm] ISO 996 - Annex A FH 6-2 29 [rpm] ISO 996 - Annex A 1 2 3 4 Q [Imp gpm] 1 2 3 4 Q [Imp gpm] 1 2 3 4 6 Q [US 7 gpm],6 1 2 3 4 6 Q [US 7 gpm],6 Hc [m], H [ft] Hc [m], H [ft] 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, GEN..D/FHF NPSHr [m] 1 6-16/11A φ 161 6-16/1 Ø 178 6-16/1 φ 178 6-16/11 φ 168 4 3 2 1 NPSHr [ft] NPSHr [m] 1 6-2/1 φ 187 6-16/1 Ø 178 6-2/22 φ 21 6-2/18 φ 198 4 3 2 1 NPSHr [ft] 2 4 6 8 1 12 14 Q [m16 3 /h] 1 1 2 2 Q [l/min] 76486_A_CH 2 4 6 8 1 12 14 Q [m16 3 /h] 1 1 2 2 Q [l/min] 76487_A_CH FH 6-2 29 [rpm] ISO 996 - Annex A FH 8-16 29 [rpm] ISO 996 - Annex A 1 2 3 4 Q [Imp gpm] 2 4 6 8 Q [Imp gpm] 1 2 3 4 6 Q [US 7 gpm],6 2 4 6 8 1, Q [US gpm] Hc [m], 1, H [ft] Hc [m],4 1, H [ft],4,3 1,,3 1,,2,2,1,,1,, 1,, 1, 4 4 1 3 1 3 NPSHr [m] 6-16/1 Ø 178 2 NPSHr [ft] NPSHr [m] 6-16/1 Ø 178 2 NPSHr [ft] 1 1 2 4 6 8 1 12 14 Q [m16 3 /h] 1 1 2 2 Q [l/min] 76488_A_CH 1 1 2 Q [m2 3 /h] 1 2 3 Q 4 [l/min] 76489_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 82

GEN..D/FHF SERIES OF BOOSTER SETS (POSITIVE SUCTION HEAD) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT FH 8-2 29 [rpm] ISO 996 - Annex A FH 8-2 29 [rpm] ISO 996 - Annex A 2 4 6 8 Q [Imp gpm] 2 4 6 8 Q [Imp gpm] 2 4 6 8 1, Q [US gpm] 2 4 6 8 1, Q [US gpm] Hc [m],4 1, H [ft] Hc [m],4 1, H [ft],3 1,,3 1,,2,2,,,1,1, 1,, 1, NPSHr [m] 1 6-16/1 Ø 178 4 3 2 1 NPSHr [ft] NPSHr [m] 1 8-2/37 φ 22 6-16/1 Ø 178 8-2/ φ 26 8-2/4 φ 238 4 3 2 1 NPSHr [ft] GEN..D/FHF 1 1 2 Q [m2 3 /h] 1 2 3 Q 4 [l/min] 7649_A_CH 1 1 2 Q [m2 3 /h] 1 2 3 Q 4 [l/min] 76491_A_CH FH 1-16 29 [rpm] ISO 996 - Annex A FH 1-2 29 [rpm] ISO 996 - Annex A 2 4 6 8 1 12 Q 14 [Imp gpm] 2 4 6 8 1 12 Q 14 [Imp gpm] 2 4 6 8 1 12 14 16,2 Q [US gpm],8 2 4 6 8 1 12 14 16,2 Q [US gpm],8 Hc [m],2 H [ft] Hc [m],2 H [ft],6,6,1,1,4,4,1,1,,2,,2, 1,, 1, 1-16/18 φ 13/16 4 1-2/18 φ 141/19 4 1 3 1 3 NPSHr [m] 1-16/3 φ 18 1-16/22 φ 19/171 6-16/1 Ø 178 2 NPSHr [ft] NPSHr [m] 6-16/1 Ø 178 1-2/4 φ 213 1-2/37 φ 23 2 NPSHr [ft] 1-2/3 φ 189/19 1 1 1 1 2 2 3 3 Q [m4 3 /h] 1 2 3 4 6 Q [l/min] 76492_A_CH 1 1 2 2 3 3 Q [m4 3 /h] 1 2 3 4 6 Q [l/min] 76493_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 83

GEN..D/FHF SERIES OF BOOSTER SETS (POSITIVE SUCTION HEAD) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT FH 1-2 29 [rpm] ISO 996 - Annex A FH 12-2 29 [rpm] ISO 996 - Annex A 1 1 Q [Imp gpm] 1 1 2 Q 2 [Imp gpm] Hc [m] 1 1,2,2 Q [US gpm],8,6 H [ft] 1 1 2 2 Q 3 [US gpm],2,8 Hc [m] H [ft],2,6,1,1,4,1,1,4,,2,,2, 1,, 1, 12-2/3 φ 162/194 GEN..D/FHF NPSHr [m] 1 1-2/3 φ 2 6-16/1 Ø 178 1-2/9 φ 267 1-2/7 φ 24 1-2/ φ 23 1-2/4 φ 221 4 3 2 1 NPSHr [ft] NPSHr [m] 1 12-2/ φ 216 12-2/4 φ 2 6-16/1 Ø 178 4 3 2 1 NPSHr [ft] 1 2 3 4 Q [m 3 /h] 2 4 6 Q [l/min] 76494_A_CH 1 2 3 4 6 Q [m7 3 /h] 2 4 6 8 1 Q [l/min] 7649_A_CH FH 12-27 29 [rpm] ISO 996 - Annex A 1 1 2 2 Q [Imp gpm] 1 1 2 2 3 Q [US 3gpm],2,8 Hc [m] H [ft],2,6,1,1,4,,2, 2, 6 1 12-27/7 φ 216/23 4 NPSHr [m] 1 12-27/132 φ 266 6-16/1 12-27/11 φ 23 Ø 178 12-27/9 φ 237 3 NPSHr [ft] 2 1 1 2 3 4 6 7 Q [m8 3 /h] 2 4 6 8 1 12 Q [l/min] 76496_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 84

GEN..D/FHF SERIES OF BOOSTER SETS (SUCTION LIFT) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT FH 32-12 29 [rpm] ISO 996 - Annex A FH 32-16 29 [rpm] ISO 996 - Annex A 2 4 6 8 1 Q [Imp gpm] 2 4 6 8 1 12 Q [US gpm], 2 4 6 8 Q 1 [Imp gpm] 2 4 6 8 1 12 Q [US gpm],6 Hc [m],4 1, H [ft] Hc [m], 1, H [ft],3 1,,4,3 1,,2,1,,2,1,, 6,, 1, 3 NPSHr [m] 4 2 1 1 NPSHr [ft] NPSHr [m] 8 6 4 2 2 2 1 1 NPSHr [ft] GEN..D/FHF 1 1 2 2 Q [m 3 /h] 3 1 2 3 4 Q [l/min] 7641_A_CH 1 1 2 2 Q [m 3 /h] 3 1 2 3 4 Q [l/min] 7642_A_CH FH 32-2 29 [rpm] ISO 996 - Annex A FH 4-12 29 [rpm] ISO 996 - Annex A 2 4 6 8 1 Q 12 [Imp gpm] 1 1 2 Q [Imp gpm] 2 4 6 8 1 12 14 Q [US gpm],6 1 1 2 Q [US 2gpm],6 Hc [m], H [ft] Hc [m], H [ft] 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, 3 8 2 4 6 2 1 3 NPSHr [m] 4 1 NPSHr [ft] NPSHr [m] 2 NPSHr [ft] 1 2 1 1 1 2 2 3 Q [m 3 /h] 3 1 2 3 4 Q [l/min] 7643_A_CH 1 2 3 4 Q [m 3 /h] 6 2 4 6 8 Q 1 [l/min] 7644_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 8

GEN..D/FHF SERIES OF BOOSTER SETS (SUCTION LIFT) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT FH 4-16 29 [rpm] ISO 996 - Annex A FH 4-2 29 [rpm] ISO 996 - Annex A 1 1 2 Q [Imp gpm] 1 1 2 Q [Imp gpm] 1 1 2 Q [US 2gpm],6 1 1 2 Q [US 2gpm],6 Hc [m], H [ft] Hc [m], H [ft] 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, GEN..D/FHF NPSHr [m] 1 4 3 2 1 NPSHr [ft] NPSHr [m] 1 4 3 2 1 NPSHr [ft] 1 2 3 4 Q [m 3 /h] 6 2 4 6 8 Q 1 [l/min] 764_A_CH 1 2 3 4 Q [m 3 /h] 6 2 4 6 8 Q 1 [l/min] 7646_A_CH FH 4-2 29 [rpm] ISO 996 - Annex A FH - 12 29 [rpm] ISO 996 - Annex A 1 1 2 Q [Imp gpm] 1 2 3 Q [Imp gpm] 1 1 2 Q [US 2gpm],6 1 2 3 4,6 Q [US gpm] Hc [m], H [ft] Hc [m], H [ft] 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, 4 4 1 3 1 3 NPSHr [m] 2 NPSHr [ft] NPSHr [m] 2 NPSHr [ft] 1 1 1 2 3 4 Q [m 3 /h] 6 2 4 6 8 Q 1 [l/min] 7647_A_CH 2 4 6 8 Q [m1 3 /h] 2 4 6 8 1 12 14 16 Q [l/min] 7648_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 86

GEN..D/FHF SERIES OF BOOSTER SETS (SUCTION LIFT) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT FH - 16 29 [rpm] ISO 996 - Annex A FH - 2 29 [rpm] ISO 996 - Annex A 1 2 3 Q [Imp gpm] 1 2 3 4 Q [Imp gpm] 1 2 3 4,6 Q [US gpm] 1 2 3 4 Q [US gpm],6 Hc [m], H [ft] Hc [m], H [ft] 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, NPSHr [m] 1 4 3 2 1 NPSHr [ft] NPSHr [m] 1 4 3 2 1 NPSHr [ft] GEN..D/FHF 2 4 6 8 Q [m1 3 /h] 2 4 6 8 1 12 14 Q 16 [l/min] 7649_A_CH 2 4 6 8 1 Q [m12 3 /h] 1 1 Q [l/min] 2 76473_A_CH FH - 2 29 [rpm] ISO 996 - Annex A FH 6-12 29 [rpm] ISO 996 - Annex A 1 2 3 4 Q [Imp gpm] 1 2 3 4 Q [Imp gpm] 1 2 3 4 Q [US gpm],6 1 2 3 4 Q [US 6 gpm],6 Hc [m], H [ft] Hc [m], H [ft] 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, 4 4 1 3 1 3 NPSHr [m] 2 NPSHr [ft] NPSHr [m] 2 NPSHr [ft] 1 1 2 4 6 8 1 Q [m12 3 /h] 1 1 Q [l/min] 2 7646_A_CH 2 4 6 8 1 12 Q [m14 3 /h] 1 1 2 Q [l/min] 76461_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 87

GEN..D/FHF SERIES OF BOOSTER SETS (SUCTION LIFT) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT FH 6-16 29 [rpm] ISO 996 - Annex A FH 6-2 29 [rpm] ISO 996 - Annex A 1 2 3 4 Q [Imp gpm] 1 2 3 4 Q [Imp gpm] 1 2 3 4 6 Q [US 7 gpm],6 1 2 3 4 6 Q [US 7 gpm],6 Hc [m], H [ft] Hc [m], H [ft] 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, GEN..D/FHF NPSHr [m] 1 6-16/11A φ 161 6-16/1 Ø 178 6-16/1 φ 178 6-16/11 φ 168 4 3 2 1 NPSHr [ft] NPSHr [m] 1 6-2/1 φ 187 6-16/1 Ø 178 6-2/22 φ 21 6-2/18 φ 198 4 3 2 1 NPSHr [ft] 2 4 6 8 1 12 14 Q [m16 3 /h] 1 1 2 2 Q [l/min] 76462_A_CH 2 4 6 8 1 12 14 Q [m16 3 /h] 1 1 2 2 Q [l/min] 76463_A_CH FH 6-2 29 [rpm] ISO 996 - Annex A FH 8-16 29 [rpm] ISO 996 - Annex A 1 2 3 4 Q [Imp gpm] 2 4 6 8 Q [Imp gpm] 1 2 3 4 6 Q [US 7 gpm],6 2 4 6 8 1,6 Q [US gpm] Hc [m], H [ft] Hc [m], H [ft] 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, 4 4 1 3 1 3 NPSHr [m] 6-16/1 Ø 178 2 NPSHr [ft] NPSHr [m] 6-16/1 Ø 178 2 NPSHr [ft] 1 1 2 4 6 8 1 12 14 Q [m16 3 /h] 1 1 2 2 Q [l/min] 76464_A_CH 1 1 2 Q [m2 3 /h] 1 2 3 Q 4 [l/min] 7646_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 88

GEN..D/FHF SERIES OF BOOSTER SETS (SUCTION LIFT) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT FH 8-2 29 [rpm] ISO 996 - Annex A FH 8-2 29 [rpm] ISO 996 - Annex A 2 4 6 8 Q [Imp gpm] 2 4 6 8 Q [Imp gpm] 2 4 6 8 1,6 Q [US gpm] 2 4 6 8 1,6 Q [US gpm] Hc [m], H [ft] Hc [m], H [ft] 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, NPSHr [m] 1 6-16/1 Ø 178 4 3 2 1 NPSHr [ft] NPSHr [m] 1 8-2/37 φ 22 6-16/1 Ø 178 8-2/ φ 26 8-2/4 φ 238 4 3 2 1 NPSHr [ft] GEN..D/FHF 1 1 2 Q [m2 3 /h] 1 2 3 Q 4 [l/min] 76466_A_CH 1 1 2 Q [m2 3 /h] 1 2 3 Q 4 [l/min] 76467_A_CH FH 1-16 29 [rpm] ISO 996 - Annex A FH 1-2 29 [rpm] ISO 996 - Annex A 2 4 6 8 1 12 Q 14 [Imp gpm] 2 4 6 8 1 12 Q 14 [Imp gpm] 2 4 6 8 1 12 14 16,2 Q [US gpm],8 2 4 6 8 1 12 14 16,2 Q [US gpm],8 Hc [m],2 H [ft] Hc [m],2 H [ft],6,6,1,1,4,4,1,1,,2,,2, 1,, 1, 1-16/18 φ 13/16 4 1-2/18 φ 141/19 4 1 3 1 3 NPSHr [m] 1-16/3 φ 18 1-16/22 φ 19/171 6-16/1 Ø 178 2 NPSHr [ft] NPSHr [m] 6-16/1 Ø 178 1-2/4 φ 213 1-2/37 φ 23 2 NPSHr [ft] 1-2/3 φ 189/19 1 1 1 1 2 2 3 3 Q [m4 3 /h] 1 2 3 4 6 Q [l/min] 76468_A_CH 1 1 2 2 3 3 Q [m4 3 /h] 1 2 3 4 6 Q [l/min] 76469_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 89

GEN..D/FHF SERIES OF BOOSTER SETS (SUCTION LIFT) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT FH 1-2 29 [rpm] ISO 996 - Annex A FH 12-2 29 [rpm] ISO 996 - Annex A 1 1 Q [Imp gpm] 1 1 2 Q 2 [Imp gpm] Hc [m] 1 1,2,2 Q [US gpm],8,6 H [ft] 1 1 2 2 Q 3 [US gpm],2,8 Hc [m] H [ft],2,6,1,1,4,1,1,4,,2,,2, 1,, 1, 12-2/3 φ 162/194 GEN..D/FHF NPSHr [m] 1 1-2/3 φ 2 6-16/1 Ø 178 1-2/9 φ 267 1-2/7 φ 24 1-2/ φ 23 1-2/4 φ 221 4 3 2 1 NPSHr [ft] NPSHr [m] 1 12-2/ φ 216 12-2/4 φ 2 6-16/1 Ø 178 4 3 2 1 NPSHr [ft] 1 2 3 4 Q [m 3 /h] 2 4 6 Q [l/min] 7647_A_CH 1 2 3 4 6 Q [m7 3 /h] 2 4 6 8 1 Q [l/min] 76471_A_CH FH 12-27 29 [rpm] ISO 996 - Annex A 1 1 2 2 Q [Imp gpm] 1 1 2 2 3 Q [US 3gpm],2,8 Hc [m] H [ft],2,6,1,1,4,,2, 2, 6 1 12-27/7 φ 216/23 4 NPSHr [m] 1 12-27/132 φ 266 6-16/1 12-27/11 φ 23 Ø 178 12-27/9 φ 237 3 NPSHr [ft] 2 1 1 2 3 4 6 7 Q [m8 3 /h] 2 4 6 8 1 12 Q [l/min] 76472_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 9

GEN..D/SHF Series Fire-fighting booster sets EN 1284, electric pumps SHF series with high efficiency motors and diesel engine pumps Hz GEN..D/SHF 91

GEN..D/SHF 92

RANGE GEN..D/SHF RANGE The range of EN 1284 fire-fighting booster sets with diesel and electric service pumps and optional jockey pump to adapt to the specific needs of every application. D.. DIESEL ENGINE PUMP Single fire-fighting centrifugal pump in horizontal design with stainless steel casing, SHF series. Head up to 1 m. Flow up to 22 m 3 /h. GEN..D SERIES Fire-fighting sets with diesel engine centrifugal service pump, in horizontal design with stainless steel casing, SHF series. Head up to 1 m. Flow up to 22 m 3 /h. GEN..1D SERIES Fire-fighting sets with diesel engine service pump and electric jockey pump. The centrifugal service pump has horizontal design and stainless steel casing. SHF series. Head up to 1 m. Flow up to 22 m 3 /h. GEN..D/SHF GEN..1D SERIES Fire-fighting sets with diesel engine centrifugal service pump. The centrifugal service pump has horizontal design and stainless steel casing. SHF series. Head up to 1 m. Flow up to 44 m 3 /h. GEN..11D SERIES Fire-fighting sets with diesel engine service pump, electric service pump and electric jockey pump. The centrifugal service pump has horizontal design and stainless steel casing. SHF series. Head up to 1 m. Flow up to 44 m 3 /h. 93

GEN..D/SHF BOOSTER SETS SERIES HYDRAULIC TABELLA DI PRESTAZIONI PERFORMANCE IDRAULICHE TABLE SERIE AT 1SV 3SV HZ SV (JOCKEY 2p Hz PUMP) PUMP TYPE NOMINAL POWER l/min 12 2 Q = DELIVERY 2 3 3 4 m 3 /h,7 1,2 1, 1,8 2,1 2,4 kw HP H = TOTAL HEAD METRES COLUMN OF WATER 1SV 2,37, 12,2 12,2 11, 1,7 9, 7,9 6, 1SV 3,37, 18, 18, 17, 1,7 13,8 11,4 8,4 1SV 4,37, 23,7 23, 22,1 2,4 17,9 14,6 1,6 1SV,37, 29,3 28,9 27, 24,8 21,6 17,4 12, 1SV 6,37, 34,8 34,2 31,7 28,9 2, 2, 14, 1SV 7,37, 4,2 39,2 36,1 32,7 28,1 22,2 1,2 1SV 8,,7 48,1 47,9 4,2 41,8 36,8 3,4 22,4 1SV 9,,7 3,7 3,4,4 46,4 4,8 33, 24,6 1SV 1,,7 9,4 9,, 1, 44,7 36,6 26,6 1SV 11,,7 6,1 64, 6,4, 48, 39, 28, 1SV 12,7 1 73,3 73,1 69,3 64,3 7,1 47,6 3,7 1SV 13,7 1 79,2 78,9 74,8 69,4 61,6 1,2 38,2 1SV 1,7 1 9,9 9, 8,6 79,3 7,1 8,1 43,1 1SV 17 1,1 1, 1,2 14,9 1, 93,1 82,6 68,6 1,2 1SV 19 1,1 1, 117, 116,7 111, 13,2 91, 7,8 6,3 1SV 22 1,1 1, 134,6 134,1 127,4 118,1 14,4 86,1 63, 1SV 2 1, 2 12,6 12,4 14, 13,4 12, 99,1 72,7 Prestazioni conformi alle norme ISO 996 - Annex A. EN1284_pp_1sv-2p-en_a_th GEN..D/SHF 94

GEN..D/SHF BOOSTER SETS SERIES SERVICE TABELLA ABBINAMENTI PUMP JOCKEY POMPA SERVIZIO PUMP COMBINATIONS SH32-8 - POMPA PILOTA GRUPPI GEN 1 SERVICE PUMP JOCKEY PUMP ELECTRIC PUMP TYPE SHF PUMP 1SV 7 32-12/7 32-12/D121 32-12/11 32-12/D136 32-16/1 32-16/D1 32-16/22 32-16/D168 32-2/3 32-2/D188 32-2/4 32-2/D24 32-2/ 32-2/D222 32-2/7 32-2/D242 32-2/11 32-2/D26 4-12/11 4-12/D112 4-12/1 4-12/D126 4-12/22 4-12/D143 4-16/3 4-16/D19 4-16/4 4-16/D171 4-2/ 4-2/D19 4-2/7 4-2/D29 4-2/11A 4-2/D218 4-2/11 4-2/D233 4-2/1 4-2/D21-12/22-12/D119-12/3-12/D13-12/4-12/D139-16/ -16/D18-16/7-16/D174-2/11A -2/D197-2/11-2/D29-2/1-2/D224-2/18-2/D237-2/22-2/D2 6-16/4 6-16/D119 6-16/ 6-16/D129 6-16/7 6-16/D137 6-16/11A 6-16/D168 6-16/11 6-16/D177 6-2/1 6-2/D192 6-2/18 6-2/D23 6-2/22 6-2/D21 6-2/3 6-2/D24 6-2/37 6-2/D2 8-16/11 8-16/D169 8-16/1 8-16/D177 8-16/18 8-16/D186 8-2/22 8-2/D198 8-2/3 8-2/D21 8-2/37 8-2/D226 8-2/4 8-2/D237 8-2/ 8-2/D22 8-2/7 8-2/D27 1SV 8 1SV 9 1SV 1 1SV 11 1SV 12 1SV 13 1SV 1 1SV 17 1SV 19 1284-SHF_ap-en_b_tc GEN..D/SHF 9

HYDRAULIC PERFORMANCE TABLE AT HZ (POSITIVE SUCTION HEAD) TABELLA DI PRESTAZIONI IDRAULICHE NETTE GRUPPI EN1284 SERIE SHF32 2 poli Hz 1 POMPA DI SERVIZIO, ASP ESCLUSA SOPRABATT GEN..D/SHF 32 BOOSTER SETS SERIES RISK CLASS TYPE RATED LHn SHF.. POWER Q = DELIVERY l/min 1 18 2 22 3 3 37 4 416 42 4 4 ELECTRIC PUMP m 3 /h 9 11 12 14 18 21 23 24 2 26 27 32 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 32-12/7 32-12/D121 1 x,7 16,7 14, 12,9 12,1 11, 7,6,1 3,7 1,9 32-12/11 32-12/D136 1 x 1,1 21,6 19, 17,9 17, 1,9 12,3 9,6 8,1 6,2 32-16/1 32-16/D1 1 x 1, 27,6 24,2 22,9 21,8 2, 16,3 13, 11,3 9,1 32-16/22 32-16/D168 1 x 2,2 3, 32, 3,9 29,9 28,7 24,7 21, 19,7 17, 16,1 1,2 13,1 32-2/3 32-2/D188 1 x 3 43,8 38,1 36,4 3,1 33,4 28, 23,9 21,6 18,8 17,1 32-2/4 32-2/D24 1 x 4 3,6 48,6 47,1 4,9 44,4 39,3 3,1 32,8 29,9 28,1 27, 24,1 32-2/ 32-2/D222 1 x, 61,7 6,3 4,6 3,2 1,6 46, 41,7 39,3 36,4 32-2/7 32-2/D242 1 x 7, 74,1 68,4 66,7 6,3 63,6 8,1 3,8 1,4 48,6 46,9 4,8 32-2/11 32-2/D26 1 x 11 86,3 79,8 77,9 76, 74,7 69, 64,7 62,3 9, 7,8 6,7 4, Performance levels relative to set with 1 service pump running and compliant with ISO 996 - Annex A. 1284_1pg-sp-shf32-2p-en_a_th LHn = risk class value referred to the required rated capacity (Tab.6 para 7.3.1 EN1284) Inlet pressure drops must be deducted. Make sure that these drops, added to the difference in level (max. 3.2m), are less than 4.m The values shown identify performance levels according to the reference standard EN1284. HYDRAULIC PERFORMANCE TABLE AT HZ (SUCTION LIFT) GEN..D/SHF 32 BOOSTER SETS SERIES TABELLA DI PRESTAZIONI IDRAULICHE NETTE GRUPPI EN1284 SERIE SHF32 2 poli Hz 1 POMPA DI SERVIZIO, ASP ESCLUSA SOTTOBATT RISK CLASS GEN..D/SHF TYPE RATED SHF.. POWER Q = DELIVERY l/min 1 18 2 22 3 3 37 4 416 42 4 4 ELECTRIC PUMP m 3 /h 9 11 12 14 18 21 23 24 2 26 27 32 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 32-12/7 32-12/D121 1 x,7 16,7 14, 12,9 12,1 11, 7,6,1 3,7 1,9 32-12/11 32-12/D136 1 x 1,1 21,6 19, 17,9 17, 1,9 12,3 9,6 8,1 6,2 32-16/1 32-16/D1 1 x 1, 27,6 24,2 22,9 21,8 2, 16,3 13, 11,3 9,1 32-16/22 32-16/D168 1 x 2,2 3, 32, 3,9 29,9 28,7 24,7 21, 19,7 17, 16,1 1,2 13,1 32-2/3 32-2/D188 1 x 3 43,8 38,1 36,4 3,1 33,4 28, 23,9 21,6 18,8 17,1 32-2/4 32-2/D24 1 x 4 3,6 48,6 47,1 4,9 44,4 39,3 3,1 32,8 29,9 28,1 27, 24,1 32-2/ 32-2/D222 1 x, 61,7 6,3 4,6 3,2 1,6 46, 41,7 39,3 36,4 32-2/7 32-2/D242 1 x 7, 74,1 68,4 66,7 6,3 63,6 8,1 3,8 1,4 48,6 46,9 4,8 32-2/11 32-2/D26 1 x 11 86,3 79,8 77,9 76, 74,7 69, 64,7 62,3 9, 7,8 6,7 4, Performance levels relative to set with 1 service pump running and compliant with ISO 996 - Annex A. 1284_1pg-st-shf32-2p-en_a_th LHn = risk class value referred to the required rated capacity (Tab.6 para 7.3.1 EN1284). Inlet pressure drops must be deducted. Make sure these drops are less than 4.m The values shown identify performance levels according to the reference standard EN1284. LHn 96

NPSH REQUIRED FOR PUMP SERIES SHF 32 TABELLA DI PRESTAZIONI IDRAULICHE NPSHr GRUPPI EN1284 SERIE SHF32 2 poli Hz RISK CLASS TYPE RATED GEN..D/SHF LHn SHF.. POWER Q = DELIVERY l/min 1 18 2 22 3 3 37 4 416 42 4 4 ELECTRIC PUMP m 3 /h 9 11 12 14 18 21 23 24 2 26 27 32 PUMP kw NPSHr [METRES COLUMN OF WATER] 32-12/7 32-12/D121 1 x,7 1, 1, 1,1 1,2 1,6 2,1 2,3 2,7 32-12/11 32-12/D136 1 x 1,1 1, 1, 1,1 1,2 1,6 2,1 2,3 2,7 32-16/1 32-16/D1 1 x 1, 1, 1,6 1,7 1,9 2, 3, 3,2 3, 32-16/22 32-16/D168 1 x 2,2 1,2 1,4 1, 1,6 2,2 2,8 3,3 3,8 4,2 4,4,2 32-2/3 32-2/D188 1 x 3 1,7 1,8 1,9 2,1 2,8 3,7 4,3,2,8 32-2/4 32-2/D24 1 x 4 1,6 1,8 2, 2,2 2,8 3,4 3,9 4,6,1, 6,9 32-2/ 32-2/D222 1 x, 2,8 3,2 3, 3,8,1 6,2 6,9 7,7 32-2/7 32-2/D242 1 x 7, 2,7 3, 3,2 3, 4,,3,8 6,3 6,6 6,9 32-2/11 32-2/D26 1 x 11 2,7 3, 3,2 3, 4,,3,8 6,3 6,6 6,9 7, The declared NPSH values were obtained in the laboratory and refer to a single service pump 1284_1p-shf32-2p_NPSHr-en_a_th LHn = risk class value referred to the required rated capacity (Tab.6 para 7.3.1 EN1284) Check that NPSHd NPSHr+1m is satisfied 97

HYDRAULIC PERFORMANCE TABLE AT HZ (POSITIVE SUCTION HEAD) TABELLA DI PRESTAZIONI IDRAULICHE NETTE GRUPPI EN1284 SERIE SHF4 2 poli Hz 1 POMPA DI SERVIZIO, ASP ESCLUSA, INST SOPRA GEN..D/SHF 4 BOOSTER SETS SERIES RISK CLASS TYPE RATED OH1n SHF.. POWER Q = DELIVERY l/min 3 37 4 64 677 7 72 7 8 833 8 1 ELECTRIC PUMP m3/h 18 23 32 38 41 42 44 4 48 1 6 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 4-12/11 4-12/D112 1 x 1,1 13,9 11,3 1, 9,3 3,4,7 4-12/1 4-12/D126 1 x 1, 18, 1,3 14, 13,3 7,4 4,7 4-12/22 4-12/D143 1 x 2,2 2,3 21,8 2, 19,8 14, 11,4 6,4, 3,6,6 4-16/3 4-16/D19 1 x 3 31,6 28,1 26,8 26, 19, 16, 1,8 9,2 7,6 4-16/4 4-16/D171 1 x 4 38,3 3,1 33,7 32,9 26, 23,6 18,1 16, 1, 11,7 4-2/ 4-2/D19 1 x, 46,4 42,7 41,2 4,4 33,1 29,7 23,3 21, 19,6 4-2/7 4-2/D29 1 x 7, 7, 3,1 1,6,7 43,8 4,7 34,8 33,2 31, 28, 4-2/11A 4-2/D218 1 x 11 63,6 7,8 6,2,2 47,8 44, 38,2 36, 34,8 31,1 4-2/11 4-2/D233 1 x 11 71,7 66, 64,3 63,4,7 2,3 4,8 44, 42,1 38,3 4-2/1 4-2/D21 1 x 1 8, 78,6 76,9 76, 68,4 6, 8,6 6,8, 1,1 42,6 Performance levels relative to set with 1 service pump running and compliant with ISO 996 - Annex A. 1284_1pg-sp-shf4-2p-en_a_th OHn = risk class value referred to the required rated capacity (Tab.6 para 7.3.1 EN1284) Inlet pressure drops must be deducted. Make sure that these drops, added to the difference in level (max. 3.2m), are less than 4.m The values shown identify performance levels according to the reference standard EN1284. HYDRAULIC PERFORMANCE TABLE AT HZ (SUCTION LIFT) TABELLA DI PRESTAZIONI IDRAULICHE NETTE GRUPPI EN1284 SERIE SHF4 2 poli Hz 1 POMPA DI SERVIZIO, ASP ESCLUSA, INST SOTT GEN..D/SHF 4 BOOSTER SETS SERIES RISK CLASS GEN..D/SHF TYPE RATED SHF.. POWER OH1n Q = DELIVERY l/min 3 37 4 64 677 7 72 7 8 833 8 1 ELECTRIC PUMP m3/h 18 23 32 38 41 42 44 4 48 1 6 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 4-12/11 4-12/D112 1 x 1,1 13,9 11,3 1, 9,3 3,4,7 4-12/1 4-12/D126 1 x 1, 18, 1,3 14, 13,3 7,4 4,7 4-12/22 4-12/D143 1 x 2,2 2,3 21,8 2, 19,8 14, 11,4 6,4, 3,6,6 4-16/3 4-16/D19 1 x 3 31,6 28,1 26,8 26, 19, 16, 1,8 9,2 7,6 4-16/4 4-16/D171 1 x 4 38,3 3,1 33,7 32,9 26, 23,6 18,1 16, 1, 11,7 4-2/ 4-2/D19 1 x, 46,4 42,7 41,2 4,4 33,1 29,7 23,3 21, 19,6 4-2/7 4-2/D29 1 x 7, 7, 3,1 1,6,7 43,8 4,7 34,8 33,2 31, 28, 4-2/11A 4-2/D218 1 x 11 63,6 7,8 6,2,2 47,8 44, 38,2 36, 34,8 31,1 4-2/11 4-2/D233 1 x 11 71,7 66, 64,3 63,4,7 2,3 4,8 44, 42,1 38,3 4-2/1 4-2/D21 1 x 1 8, 78,6 76,9 76, 68,4 6, 8,6 6,8, 1,1 42,6 Performance levels relative to set with 1 service pump running and compliant with ISO 996 - Annex A. 1284_1pg-st-shf4-2p-en_a_th OHn = risk class value referred to the required rated capacity (Tab.6 para 7.3.1 EN1284) Inlet pressure drops must be deducted. Make sure these drops are less than 4.m The values shown identify performance levels according to the reference standard EN1284. 98

NPSH REQUIRED FOR PUMP SERIES SHF 4 TABELLA DI PRESTAZIONI IDRAULICHE GRUPPI EN1284 SERIE SHF4 2 poli Hz 1 POMPA DI SERVIZIO RISK CLASS TYPE RATED GEN..D/SHF OH1n OH1m SHF.. POWER Q = DELIVERY l/min 3 37 4 64 677 7 72 7 8 833 8 1 ELECTRIC PUMP m 3 /h 18 23 32 38 41 42 44 4 48 1 6 PUMP kw NPSHr [METRES COLUMN OF WATER] 4-12/11 4-12/D112 1 x 1,1,7 1, 1, 2, 4-12/1 4-12/D126 1 x 1,,7 1, 1, 2, 2,3 2, 4-12/22 4-12/D143 1 x 2,2,7 1, 1, 2, 2,3 2, 2,8 3,1 4-16/3 4-16/D19 1 x 3 1,1 1,4 2,1 2,6 2,9 3,2 3, 3,8 4-16/4 4-16/D171 1 x 4 1,1 1,4 2,1 2,6 2,9 3,2 3, 3,8 4,9 4-2/ 4-2/D19 1 x, 1,4 1,8 2,7 3,4 3,7 3,9 4,2 4,,4 4-2/7 4-2/D29 1 x 7, 1,4 1,8 2,7 3,4 3,7 3,9 4,2 4,,4 6,4 4-2/11A 4-2/D218 1 x 11 1,4 1,4 1,7 3, 4,1, 4-2/11 4-2/D233 1 x 11 1,3 1,4 1,6 1,8 1,9 4-2/1 4-2/D21 1 x 1 1,3 1,4 1,6 1,8 1,9 2,1 2,2 2, 3,3 4,3, The declared NPSH values were obtained in the laboratory and refer to a single service pump OHn, OHm = risk class value referred to the required rated and maximum capacity (Tab.6 para 7.3.1 EN1284) Check that NPSHd NPSHr+1m is satisfied at the maximum requested capacity 1284_1p-shf4-2p_NPSHr-en_a_th 99

HYDRAULIC PERFORMANCE TABLE AT HZ (POSITIVE SUCTION HEAD) TABELLA DI PRESTAZIONI IDRAULICHE NETTE GRUPPI EN1284 SERIE SHF 2 poli Hz 1 POMPA DI SERVIZIO, ASPESCLUSA INST SOPRA GEN..D/SHF BOOSTER SETS SERIES RISK CLASS TYPE RATED OH2n OH3n SHF.. POWER Q = DELIVERY l/min 6 68 72 1 11 12 13 13 138 14 14 1 ELECTRIC PUMP m3/h 36 41 44 6 66 72 78 81 83 84 87 9 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER -12/22-12/D119 1 x 2,2 17,2 13,2 12, 11,3,9 3,6 1,2-12/3-12/D13 1 x 3 21,7 17,4 16,1 1,3 9,8 7,6,2 2,8-12/4-12/D139 1 x 4 2,6 21,8 2,6 19,8 14,4 12,1 9,8 7,3 6,,3 4,7-16/ -16/D18 1 x, 34, 29,3 27,8 26,9 2,4 17, 14,4 11,1 9,4 8,3 7,6-16/7-16/D174 1 x 7, 4,7 36,1 34,7 33,9 27,6 24,7 21,6 18,1 16,3 1,2 14,4 12, 1,4-2/11A -2/D197 1 x 11 34, 29,3 27,8 26,9 2,4 17, 14,4 11,1 9,4 8,3 7,6-2/11-2/D29 1 x 11 4,7 36,1 34,7 33,9 27,6 24,7 21,6 18,1 16,3 1,2 14,4 12, -2/1-2/D224 1 x 1 7,3 6, 64, 63, 4,6,4 4,4 39,6-2/18-2/D237 1 x 18, 8,1 73,8 72,1 71,1 62,8 8,7 4,1 48,9 46, 44,2-2/22-2/D2 1 x 22 88,9 83,2 81,6 8,6 72,3 68,4 64, 9,1 6,4 4,7 3,6,6 Performance levels relative to set with 1 service pump running and compliant with ISO 996 - Annex A. 1284_1pg-sp-shf-2p-en_a_th OHn = risk class value referred to the required rated capacity (Tab.6 para 7.3.1 EN1284) Inlet pressure drops must be deducted. Make sure that these drops, added to the difference in level (max. 3.2m), are less than 4.m The values shown identify performance levels according to the reference standard EN1284. GEN..D/SHF HYDRAULIC PERFORMANCE TABLE AT HZ (SUCTION LIFT) GEN..D/SHF BOOSTER SETS SERIES TABELLA DI PRESTAZIONI IDRAULICHE NETTE GRUPPI EN1284 SERIE SHF 2 poli Hz 1 POMPA DI SERVIZIO, ASPESCLUSA INST SOTTO TYPE RATED SHF.. POWER OH2n l/min 6 68 72 1 11 12 13 13 138 14 14 1 ELECTRIC PUMP m3/h 36 41 44 6 66 72 78 81 83 84 87 9 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER -12/22-12/D119 1 x 2,2 17,2 13,2 12, 11,3,9 3,6 1,2-12/3-12/D13 1 x 3 21,7 17,4 16,1 1,3 9,8 7,6,2 2,8-12/4-12/D139 1 x 4 2,6 21,8 2,6 19,8 14,4 12,1 9,8 7,3 6,,3 4,7-16/ -16/D18 1 x, 34, 29,3 27,8 26,9 2,4 17, 14,4 11,1 9,4 8,3 7,6-16/7-16/D174 1 x 7, 4,7 36,1 34,7 33,9 27,6 24,7 21,6 18,1 16,3 1,2 14,4 12, 1,4-2/11A -2/D197 1 x 11 34, 29,3 27,8 26,9 2,4 17, 14,4 11,1 9,4 8,3 7,6-2/11-2/D29 1 x 11 4,7 36,1 34,7 33,9 27,6 24,7 21,6 18,1 16,3 1,2 14,4 12, -2/1-2/D224 1 x 1 7,3 6, 64, 63, 4,6,4 4,4 39,6-2/18-2/D237 1 x 18, 8,1 73,8 72,1 71,1 62,8 8,7 4,1 48,9 46, 44,2-2/22-2/D2 1 x 22 88,9 83,2 81,6 8,6 72,3 68,4 64, 9,1 6,4 4,7 3,6,6 Performance levels relative to set with 1 service pump running and compliant with ISO 996 - Annex A. 1284_1pg-st-shf-2p-en_a_th OHn = risk class value referred to the required rated capacity (Tab.6 para 7.3.1 EN1284) Inlet pressure drops must be deducted. Make sure these drops are less than 4.m The values shown identify performance levels according to the reference standard EN1284. OH3n RISK CLASS Q = DELIVERY 1

NPSH REQUIRED FOR PUMP SERIES SHF TABELLA DI PRESTAZIONI IDRAULICHE NPSHr GRUPPI EN1284 SERIE SHF 2 poli Hz 1 POMPA DI SERVIZIO RISK CLASS TYPE RATED OH2n OH2m GEN..D/SHF OH3n OH3m SHF.. POWER Q = DELIVERY l/min 6 68 72 1 11 12 13 13 138 14 14 1 ELECTRIC PUMP m 3 /h 36 41 44 6 66 72 78 81 83 84 87 9 PUMP kw NPSHr [METRES COLUMN OF WATER] -12/22-12/D119 1 x 2,2 1,6 1,8 1,9 2,8 3,4 4,3-12/3-12/D13 1 x 3 1,6 1,8 1,9 2,7 3,1 3,7 4,6-12/4-12/D139 1 x 4 1,6 1,8 1,9 2,7 3,1 3,7 4,6,2,7 6, -16/ -16/D18 1 x, 2, 2,1 2,1 2,8 3,2 3,7 4,7,4,9 6,3-16/7-16/D174 1 x 7, 1,9 2,1 2,2 2,8 3,1 3,6 4,3 4,9,3,6 6, 7,6-2/11A -2/D197 1 x 11 2, 2,1 2,1 2,8 3,2 4,,2 6,1 6,7 7,2-2/11-2/D29 1 x 11 1,9 2,1 2,2 2,8 3,2 3,7 4,7,4,9 6,3 7, -2/1-2/D224 1 x 1 1,6 1,7 1,8 2,3 2,7 3,3 4,8-2/18-2/D237 1 x 18, 1, 1,7 1,8 2,4 2,7 3,1 3,7 4,1 4,4-2/22-2/D2 1 x 22 1, 1,7 1,8 2,4 2,7 3,1 3,7 4,1 4,4 4,7,4 The declared NPSH values were obtained in the laboratory and refer to a single service pump OHn, OHm = risk class value referred to the required rated and maximum capacity (Tab.6 para 7.3.1 EN1284) Check that NPSHd NPSHr+1m is satisfied at the maximum requested capacity 1284_1p-shf-2p_NPSHr-en_a_th 11

HYDRAULIC PERFORMANCE TABLE AT HZ (POSITIVE SUCTION HEAD) TABELLA DI PRESTAZIONI IDRAULICHE NETTE GRUPPI EN1284 SERIE SHF6 2 poli Hz 1 POMPA DI SERVIZIO, ASP ESCLUSA INST SOPRA GEN..D/SHF 6 BOOSTER SETS SERIES RISK CLASS TYPE RATED OH3n OH4n SHF.. POWER Q = DELIVERY l/min 8 9 1 11 13 1 18 19 2 2 21 22 ELECTRIC PUMP m3/h 48 4 6 66 81 9 18 114 12 123 126 132 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 6-16/4 6-16/D119 1 x 4 19,6 1,9 14,9 13,8 12,6 9,4 7,3 2,9 6-16/ 6-16/D129 1 x, 24,2 2, 19, 18,4 17,2 13,9 11,7 7,,4 6-16/7 6-16/D137 1 x 7, 28,2 2,1 24,2 23,1 22, 18,8 16,7 12, 1,4 8,7 6-16/11A 6-16/D168 1 x 11 38,2 34,3 33, 31, 29,8 2,2 22, 1,2 12,9 6-16/11 6-16/D177 1 x 11 42,9 39,7 38,4 36,9 3,3 3,6 27,4 2, 18,1 1,6 6-2/1 6-2/D192 1 x 1 3, 47, 4,9 44,1 38,9 3,3 27,1 24,1 6-2/18 6-2/D23 1 x 18, 6,2,2 3,6 1,9 46,9 43,4 3, 32,6 29, 6-2/22 6-2/D21 1 x 22 68, 63, 61,6 6,,2 1,9 44,3 41, 38, 37, 3, 6-2/3 6-2/D24 1 x 3 83,7 8,2 78,9 74,9 71,9 64,4 61,4 8,3 6,6 4,9 6-2/37 6-2/D2 1 x 37 96,7 93,6 92,2 88, 84,9 77,4 74,6 71,7 7,1 68, 6,2 Performance levels relative to set with 1 service pump running and compliant with ISO 996 - Annex A. 1284_1pg-sp-shf6-2p-en_a_th OHn = risk class value referred to the required rated capacity (Tab.6 para 7.3.1 EN1284) Inlet pressure drops must be deducted. Make sure that these drops, added to the difference in level (max. 3.2m), are less than 4.m The values shown identify performance levels according to the reference standard EN1284. GEN..D/SHF HYDRAULIC PERFORMANCE TABLE AT HZ (SUCTION LIFT) TABELLA DI PRESTAZIONI IDRAULICHE NETTE GRUPPI EN1284 SERIE SHF6 2 poli Hz 1 POMPA DI SERVIZIO, ASP ESCLUSA INST SOTTO GEN..D/SHF 6 BOOSTER SETS SERIES TYPE RATED SHF.. POWER Q = DELIVERY l/min 8 9 1 11 13 1 18 19 2 2 21 22 ELECTRIC PUMP m3/h 48 4 6 66 81 9 18 114 12 123 126 132 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 6-16/4 6-16/D119 1 x 4 19,6 1,9 14,9 13,8 12,6 9,4 7,3 2,9 6-16/ 6-16/D129 1 x, 24,2 2, 19, 18,4 17,2 13,9 11,7 7,,4 6-16/7 6-16/D137 1 x 7, 28,2 2,1 24,2 23,1 22, 18,8 16,7 12, 1,4 8,7 6-16/11A 6-16/D168 1 x 11 38,2 34,3 33, 31, 29,8 2,2 22, 1,2 12,9 6-16/11 6-16/D177 1 x 11 42,9 39,7 38,4 36,9 3,3 3,6 27,4 2, 18,1 1,6 6-2/1 6-2/D192 1 x 1 3, 47, 4,9 44,1 38,9 3,3 27,1 24,1 6-2/18 6-2/D23 1 x 18, 6,2,2 3,6 1,9 46,9 43,4 3, 32,6 29, 6-2/22 6-2/D21 1 x 22 68, 63, 61,6 6,,2 1,9 44,3 41, 38, 37, 3, 6-2/3 6-2/D24 1 x 3 83,7 8,2 78,9 74,9 71,9 64,4 61,4 8,3 6,6 4,9 6-2/37 6-2/D2 1 x 37 96,7 93,6 92,2 88, 84,9 77,4 74,6 71,7 7,1 68, 6,2 Performance levels relative to set with 1 service pump running and compliant with ISO 996 - Annex A. 1284_1pg-st-shf6-2p-en_a_th OHn = risk class value referred to the required rated capacity (Tab.6 para 7.3.1 EN1284) Inlet pressure drops must be deducted. Make sure these drops are less than 4.m The values shown identify performance levels according to the reference standard EN1284. OH3n RISK CLASS OH4n 12

NPSH REQUIRED FOR PUMP SERIES SHF 6 TABELLA DI PRESTAZIONI IDRAULICHE NPSHr GRUPPI EN1284 SERIE SHF6 2 poli Hz 1 POMPA DI SERVIZIO RISK CLASS TYPE RATED GEN..D/SHF OH3n OH3m OH4n OH4m SHF.. POWER Q = DELIVERY l/min 8 9 1 11 13 14 1 18 19 2 21 22 ELECTRIC PUMP m 3 /h 48 4 6 66 81 84 9 18 114 12 126 132 PUMP kw NPSHr [METRES COLUMN OF WATER] 6-16/4 6-16/D119 1 x 4 1,9 1,8 1,9 1,9 2, 2,7 3,3 7,4 6-16/ 6-16/D129 1 x, 1,9 1,9 1,9 1,9 2,4 2,6 3,1,4 6,6 6-16/7 6-16/D137 1 x 7, 1,9 1,9 1,9 1,9 2,4 2,6 3,1,4 6,6 8, 6-16/11A 6-16/D168 1 x 11 1,3 1,4 1,6 1,7 2,1 2,1 2,4 3, 4,2 6-16/11 6-16/D177 1 x 11 1,3 1,4 1,6 1,7 2,1 2,1 2,4 3, 4,2,2 6-2/1 6-2/D192 1 x 1 1,7 1,7 1,6 1,7 1,7 1,9 4,1 6,4 6-2/18 6-2/D23 1 x 18, 1,7 1,7 1,6 1,7 1,7 1,9 3, 3,9,3 6-2/22 6-2/D21 1 x 22 1,7 1,7 1,6 1,7 1,7 1,9 3, 3,9,3 7, 6-2/3 6-2/D24 1 x 3 1,3 1,3 1,4 1, 1,7 3,2 4,1,4 7, 6-2/37 6-2/D2 1 x 37 1,3 1,3 1,3 1,4 1,6 2,9 3,7 4,8 6,2 8,1 The declared NPSH values were obtained in the laboratory and refer to a single service pump OHn, OHm = risk class value referred to the required rated and maximum capacity (Tab.6 para 7.3.1 EN1284) Check that NPSHd NPSHr+1m is satisfied at the maximum requested capacity 1284_1p-shf6-2p_NPSHr-en_a_th 13

HYDRAULIC PERFORMANCE TABLE AT HZ (POSITIVE SUCTION HEAD) TABELLA DI PRESTAZIONI IDRAULICHE NETTE GRUPPI EN1284 SERIE SHF8 2 poli Hz 1 POMPA DI SERVIZIO, ASP ESCLUSA INST SOPRA GEN..D/SHF 8 BOOSTER SETS SERIES RISK CLASS TYPE RATED OH4n HH1n SHF.. POWER Q = DELIVERY l/min 12 1 18 21 23 3216 33 3 36 37 38 4 ELECTRIC PUMP m3/h 72 9 18 126 138 193 198 21 216 222 228 24 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 8-16/11 8-16/D169 1 x 11 33, 3,9 28,6 2,7 22,2 19,7 6,2 4,8 8-16/1 8-16/D177 1 x 1 39, 37,8 3,6 32,7 29,4 26,9 13,2 11,8 8,4 8-16/18 8-16/D186 1 x 18, 46,4 44,7 42,6 39,8 36,6 34,2 2,7 19,3 1,9 14,1 12,4 8-2/22 8-2/D198 1 x 22 1,9 48, 4,8 42, 4,1 26,7 2,3 21,9 2,2 8-2/3 8-2/D21 1 x 3 62,2 9,7 7,1 3,9 1, 37,8 36,4 32,9 31,1 29,3 27,4 8-2/37 8-2/D226 1 x 37 69,8 69,9 68,1 6,7 62,8 6, 47,2 4,7 42,2 4,4 38, 36,6 32,7 8-2/4 8-2/D237 1 x 4 82,2 79,1 76,2 72,6 69,8 3,3 1, 47, 44,6 8-2/ 8-2/D22 1 x 93,9 91,9 89,2 8,9 83,2 67,7 66, 61,8 9,6 7,3 8-2/7 8-2/D27 1 x 7 19,7 18,6 16, 12,7 1,2 8, 83,3 79,2 77, 74,8 72, Performance levels relative to set with 1 service pump running and compliant with ISO 996 - Annex A. 1284_1pg-sp-shf8-2p-en_a_th OHn = risk class value referred to the required rated capacity (Tab.6 para 7.3.1 EN1284) Inlet pressure drops must be deducted. Make sure that these drops, added to the difference in level (max. 3.2m), are less than 4.m The values shown identify performance levels according to the reference standard EN1284. GEN..D/SHF HYDRAULIC PERFORMANCE TABLE AT HZ (SUCTION LIFT) TABELLA DI PRESTAZIONI IDRAULICHE NETTE GRUPPI EN1284 SERIE SHF8 2 poli Hz 1 POMPA DI SERVIZIO, ASP ESCLUSA INST SOTTO GEN..D/SHF 8 BOOSTER SETS SERIES TYPE RATED SHF.. POWER OH4n l/min 12 1 18 21 23 3216 33 3 36 37 38 4 ELECTRIC PUMP m3/h 72 9 18 126 138 193 198 21 216 222 228 24 PUMP kw H = TOTAL HEAD METRES COLUMN OF WATER 8-16/11 8-16/D169 1 x 11 33, 3,9 28,6 2,7 22,2 19,7 6,2 4,8 8-16/1 8-16/D177 1 x 1 39, 37,8 3,6 32,7 29,4 26,9 13,2 11,8 8,4 8-16/18 8-16/D186 1 x 18, 46,4 44,7 42,6 39,8 36,6 34,2 2,7 19,3 1,9 14,1 12,4 8-2/22 8-2/D198 1 x 22 1,9 48, 4,8 42, 4,1 26,7 2,3 21,9 2,2 8-2/3 8-2/D21 1 x 3 62,2 9,7 7,1 3,9 1, 37,8 36,4 32,9 31,1 29,3 27,4 8-2/37 8-2/D226 1 x 37 69,8 69,9 68,1 6,7 62,8 6, 47,2 4,7 42,2 4,4 38, 36,6 32,7 8-2/4 8-2/D237 1 x 4 82,2 79,1 76,2 72,6 69,8 3,3 1, 47, 44,6 8-2/ 8-2/D22 1 x 93,9 91,9 89,2 8,9 83,2 67,7 66, 61,8 9,6 7,3 8-2/7 8-2/D27 1 x 7 19,7 18,6 16, 12,7 1,2 8, 83,3 79,2 77, 74,8 72, Performance levels relative to set with 1 service pump running and compliant with ISO 996 - Annex A. 1284_1pg-st-shf8-2p-en_a_th OHn = risk class value referred to the required rated capacity (Tab.6 para 7.3.1 EN1284) Inlet pressure drops must be deducted. Make sure these drops are less than 4.m The values shown identify performance levels according to the reference standard EN1284. HH1n RISK CLASS Q = DELIVERY 14

NPSH REQUIRED FOR PUMP SERIES SHF 8 TABELLA DI PRESTAZIONI IDRAULICHE GRUPPI EN1284 SERIE SHF8 2 poli Hz 1 POMPA DI SERVIZIO RISK CLASS TYPE RATED OH4n GEN..D/SHF OH4m HH1n HH1m SHF.. POWER Q = DELIVERY l/min 12 1 18 21 23 3216 33 3 36 37 38 4 ELECTRIC PUMP m 3 /h 72 9 18 126 138 193 198 21 216 222 228 24 PUMP kw NPSHr [METRES COLUMN OF WATER] 8-16/11 8-16/D169 1 x 11 2,3 2, 2,7 3, 3,2,9 6, 8-16/1 8-16/D177 1 x 1 2,3 2, 2,7 2,9 3, 4,3 4,6, 8-16/18 8-16/D186 1 x 18, 2,3 2, 2,7 2,9 3, 4,3 4,6, 6,1 6,8 8-2/22 8-2/D198 1 x 22 2,2 2,4 2,7 2,8 3,9 4,1 4,6 4,9 8-2/3 8-2/D21 1 x 3 2,2 2,4 2,6 2,8 3,7 3,8 4,2 4,4 4,7, 8-2/37 8-2/D226 1 x 37 2, 2,2 2,4 2,6 2,8 3,7 3,8 4,2 4,4 4,7, 6, 8-2/4 8-2/D237 1 x 4 1,9 2,2 2,4 2,6 3,6 3,7 4,2 4,6 8-2/ 8-2/D22 1 x 1,9 2,2 2,4 2,6 3,6 3,7 4,2 4,6,1 8-2/7 8-2/D27 1 x 7 1,9 2,2 2,4 2,6 3,6 3,7 4,2 4,6,1 6, The declared NPSH values were obtained in the laboratory and refer to a single service pump 1284_1p-shf8-2p_NPSHr-en_a_th OHn, OHm, HHn, HHm = risk class value referred to the required rated and maximum capacity (Tab.6 para 7.3.1, Tab.7 para 7.3.2 EN1284) Check that NPSHd NPSHr+1m is satisfied at the maximum requested capacity 1

GEN..D/SHF GEN..D/SHF 32-8 BOOSTER SETS TABELLA DATI ELETTRICI GRUPPI GEN..D/SHF 2 poli Hz ELECTRICAL DATA A TABLE AT Hz SERVICE ELECTRIC JOCKEY CURRENT (*) PUMP PUMP ABSORBED SET 3 X 4 V 1 x 23V 3x4 TYPE NOMINAL 1x23V 3x4V SHF.. POWER ELECTRIC Pn In TYPE Pn In In GEN..D GEN..1D GEN..1D GEN..11D PUMP PUMP kw A kw A A A A A A 32-12/7 32-12/D121,7 1,76 1SV 7,37 2,82 1,3 3,82 4,76 6,11 32-12/11 32-12/D136 1,1 2,36 1SV 8, 3,88 1,48 3 6,88,36 6,84 32-16/1 32-16/D1 1, 3,2 1SV 8, 3,88 1,48 3 6,88 6,2 7, 32-16/22 32-16/D168 2,2 4,64 1SV 9, 3,88 1,48 3 6,88 7,64 9,1 32-2/3 32-2/D188 3,91 1SV 11, 3,88 1,48 3 6,88 8,91 1,4 32-2/4 32-2/D24 4 7, 1SV 12,7 4,88 1,76 3 7,88 1, 12,3 32-2/ 32-2/D222, 11 1SV 12,7 4,88 1,76 3 7,88 14 1,8 32-2/7 32-2/D242 7, 14,3 1SV 1,7 4,88 1,76 3 7,88 17,3 19,1 32-2/11 32-2/D26 11 19,8 1SV 17 1,1 6,77 2,36 3 9,77 22,8 2,2 4-12/11 4-12/D112 1,1 2,36 1SV 7,37 2,82 1,3 3,82,36 6,71 4-12/1 4-12/D126 1, 3,2 1SV 7,37 2,82 1,3 3,82 6,2 7,37 4-12/22 4-12/D143 2,2 4,64 1SV 8, 3,88 1,48 3 6,88 7,64 9,1 4-16/3 4-16/D19 3,91 1SV 9, 3,88 1,48 3 6,88 8,91 1,4 4-16/4 4-16/D171 4 7, 1SV 1, 3,88 1,48 3 6,88 1, 12, 4-2/ 4-2/D19, 11 1SV 11, 3,88 1,48 3 6,88 14 1, 4-2/7 4-2/D29 7, 14,3 1SV 12,7 4,88 1,76 3 7,88 17,3 19,1 4-2/11A 4-2/D218 11 19,8 1SV 13,7 4,88 1,76 3 7,88 22,8 24,6 4-2/11 4-2/D233 11 19,8 1SV 1,7 4,88 1,76 3 7,88 22,8 24,6 4-2/1 4-2/D21 1 26,2 1SV 17 1,1 6,77 2,36 3 9,77 29,2 31,6-12/22-12/D119 2,2 4,64 1SV 7,37 2,82 1,3 3,82 7,64 9, -12/3-12/D13 3,91 1SV 8, 3,88 1,48 3 6,88 8,91 1,4-12/4-12/D139 4 7, 1SV 8, 3,88 1,48 3 6,88 1, 12, -16/ -16/D18, 11 1SV 9, 3,88 1,48 3 6,88 14 1, -16/7-16/D174 7, 14,3 1SV 1, 3,88 1,48 3 6,88 17,3 18,8-2/11A -2/D197 11 19,8 1SV 12,7 4,88 1,76 3 7,88 22,8 24,6-2/11-2/D29 11 19,8 1SV 12,7 4,88 1,76 3 7,88 22,8 24,6-2/1-2/D224 1 26,2 1SV 1,7 4,88 1,76 3 7,88 29,2 31, -2/18-2/D237 18, 32,9 1SV 1,7 4,88 1,76 3 7,88 3,9 37,7-2/22-2/D2 22 39,1 1SV 17 1,1 6,77 2,36 3 9,77 42,1 44, 6-16/4 6-16/D119 4 7, 1SV 8, 3,88 1,48 3 6,88 1, 12, 6-16/ 6-16/D129, 11 1SV 8, 3,88 1,48 3 6,88 14 1, 6-16/7 6-16/D137 7, 14,3 1SV 8, 3,88 1,48 3 6,88 17,3 18,8 6-16/11A 6-16/D168 11 19,8 1SV 1, 3,88 1,48 3 6,88 22,8 24,3 6-16/11 6-16/D177 11 19,8 1SV 1, 3,88 1,48 3 6,88 22,8 24,3 6-2/1 6-2/D192 1 26,2 1SV 12,7 4,88 1,76 3 7,88 29,2 31, 6-2/18 6-2/D23 18, 32,9 1SV 12,7 4,88 1,76 3 7,88 3,9 37,7 6-2/22 6-2/D21 22 39,1 1SV 1,7 4,88 1,76 3 7,88 42,1 43,9 6-2/3 6-2/D24 3 3,6 1SV 17 1,1 6,77 2,36 3 9,77 6,6 9, 6-2/37 6-2/D2 37 6,8 1SV 17 1,1 6,77 2,36 3 9,77 68,8 71,2 8-16/11 8-16/D169 11 19,8 1SV 9, 3,88 1,48 3 6,88 22,8 24,3 8-16/1 8-16/D177 1 26,7 1SV 1, 3,88 1,48 3 6,88 29,7 31,2 8-16/18 8-16/D186 18, 32,9 1SV 11, 3,88 1,48 3 6,88 3,9 37,4 8-2/22 8-2/D198 22 39,1 1SV 12,7 4,88 1,76 3 7,88 42,1 43,9 8-2/3 8-2/D21 3 3,6 1SV 13,7 4,88 1,76 3 7,88 6,6 8,4 8-2/37 8-2/D226 37 6,8 1SV 1,7 4,88 1,76 3 7,88 68,8 7,6 8-2/4 8-2/D237 4 78 1SV 1,7 4,88 1,76 3 7,88 81 82,8 8-2/ 8-2/D22 9 1SV 17 1,1 6,77 2,36 3 9,77 98 1,4 8-2/7 8-2/D27 7 129 1SV 19 1,1 6,77 2,36 3 9,77 132 134,4 ENMTP-SHF_2p-en_d_te (*) The current indicated is the maximum current absorbed. At the set 3x4V three-phase power supply GEN..1D and GEN..11D to add the control panel current of the engine pump (GEN..D) 1x23V The sets GEN..1D have the electric jockey pump 1x23V single-phase power supply. 16

Fire-fighting booster sets EN 1284 MARKET SECTORS CIVIL, INDUSTRIAL APPLICATIONS Fixed fire-fighting systems. Automatic Sprinkler systems. DSHF Series SPECIFICATIONS Flow up to 22 m 3 /h. Diesel engine with battery start. GEN..D/SHF Head up to 1 m. Panel supply power voltage: 1 x 23V ± 1%. Frequency: Hz. Voltage for controls outside panel: 12-24 Vac. Protection grade: - electric panel: IP4. Electric pumps maximum power 7 kw. Diesel engine service pump in horizontal design: - SHF series. Maximum running pressure: 12 bar. 17

DSHF 32-8 DIESEL ENGINE PUMP SERIES FIRE-FIGHTING EN 1284 For the overall dimensions of the fuel tank and the starting batteries, see tables on pages 2-2. GEN..D/SHF 18

DSHF 32-8 DIESEL ENGINE PUMP SERIES FIRE-FIGHTING EN 1284 D.. DNA DNM A B C E F H H1 H2 SHFE32-12/D121 R 2" 32 4 3 8 71 9 262 42 63 SHFE32-12/D136 R 2" 32 4 3 8 71 9 262 42 63 SHFE32-16/D1 R 2" 32 4 3 8 69 9 282 442 6 SHFE32-16/D168 R 2" 32 4 3 8 69 9 282 442 6 SHFE32-2/D188 R 2" 32 4 3 8 69 9 26 44 63 SHFE32-2/D24 R 2" 32 4 8 79 9 26 44 63 SHFE32-2/D222 R 2" 32 4 1 8 9 28 68 SHFE32-2/D242 R 2" 32 4 1 8 9 28 69 SHFE32-2/D26 R 2" 32 4 1 72 1 28 69 SHFE4-12/D112 6 4 4 3 8 69 9 262 42 63 SHFE4-12/D126 6 4 4 3 8 69 9 262 42 63 SHFE4-12/D143 6 4 4 3 8 69 9 262 42 63 SHFE4-16/D19 6 4 4 3 8 69 9 282 442 6 SHFE4-16/D171 6 4 4 3 8 69 9 282 442 6 SHFE4-2/D19 6 4 4 1 77 9 31 49 71 SHFE4-2/D29 6 4 4 1 77 9 31 49 72 SHFE4-2/D218 6 4 3 48 1 82 1 28 69 SHFE4-2/D233 6 4 3 48 1 92 12 33 8 SHFE4-2/D21 6 4 3 48 1 92 12 33 8 SHFE-12/D119 6 4 3 1 69 9 282 442 6 SHFE-12/D13 6 4 3 1 69 9 282 442 6 SHFE-12/D139 6 4 1 74 9 282 442 6 SHFE-16/D18 6 4 1 77 9 31 49 71 SHFE-16/D174 6 4 1 77 9 31 49 72 SHFE-2/D197 6 3 48 1 82 1 31 1 72 SHFE-2/D29 6 3 48 1 82 12 31 1 72 SHFE-2/D224 6 3 48 1 92 12 33 8 SHFE-2/D237 6 3 48 1 97 13 38 8 SHFE-2/D2 6 3 48 1 97 13 38 6 8 SHFE6-16/D119 8 6 4 1 7 9 26 46 63 SHFE6-16/D129 8 6 4 1 8 9 31 1 71 SHFE6-16/D137 8 6 3 48 1 8 1 31 1 72 SHFE6-16/D168 8 6 3 48 1 82 1 31 1 72 SHFE6-16/D177 8 6 3 48 1 92 12 36 6 83 SHFE6-2/D192 8 6 3 48 1 92 12 33 8 SHFE6-2/D23 8 6 3 48 1 97 13 38 8 SHFE6-2/D21 8 6 3 48 1 97 13 38 6 9 SHFE6-2/D24 8 6 64 9 1 113 1 36 61 1 SHFE6-2/D2 8 6 64 9 1 113 1 36 61 11 SHFE8-16/D169 1 8 3 48 12 92 12 33 8 SHFE8-16/D177 1 8 3 48 12 92 12 33 8 SHFE8-16/D186 1 8 3 48 12 97 13 38 6 8 SHFE8-2/D198 1 8 3 48 12 97 14 38 63 9 SHFE8-2/D21 1 8 64 9 12 19 1 36 61 1 SHFE8-2/D226 1 8 64 9 12 19 1 36 61 11 SHFE8-2/D237 1 8 64 9 12 118 1 36 64 13 SHFE8-2/D22 1 8 66 61 12 124 17 39 67 18 SHFE8-2/D27 1 8 7 6 12 131 2 42 7 19 Dimensions in mm. Tolerance ± 1 mm. d_shfe-en_f_td GEN..D/SHF 19

GEN..D/SHF 11

Fire-fighting booster sets EN 1284 MARKET SECTORS CIVIL, INDUSTRIAL APPLICATIONS Fixed fire-fighting systems. Automatic Sprinkler systems. GEN..D/SHF Series SPECIFICATIONS Flow up to 22 m 3 /h. Diesel engine with battery start. GEN..D/SHF Head up to 1 m. Panel supply power voltage: 1 x 23V ± 1%. Frequency: Hz. Voltage for controls outside panel: 12-24 Vac. Protection grade: - electric panel: IP4. Electric pumps maximum power 7 kw. Diesel engine service pump in horizontal design: - SHF series. Maximum running pressure: 12 bar. 111

GEN..D/SHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..D/SHF For the overall dimensions of the fuel tank and the starting batteries, see tables on pages 2-2. 112

GEN..D/SHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..D DRW N DNA DNM A B D E G N P Q SHF32-12/D121 1 R 2" R 1"1/2 4 3 8 71 262 9 913 1487 SHF32-12/D136 1 R 2" R 1"1/2 4 3 8 71 262 9 913 1487 SHF32-16/D1 1 R 2" R 1"1/2 4 3 8 69 282 9 93 127 SHF32-16/D168 1 R 2" R 1"1/2 4 3 8 69 282 9 93 127 SHF32-2/D188 1 R 2" R 1"1/2 4 3 8 69 26 9 91 12 SHF32-2/D24 1 R 2" R 1"1/2 4 8 79 26 9 91 12 SHF32-2/D222 1 R 2" R 1"1/2 4 1 8 28 9 116 19 SHF32-2/D242 1 R 2" R 1"1/2 4 1 8 28 9 116 19 SHF32-2/D26 1 R 2" R 1"1/2 4 1 72 28 1 116 19 SHF4-12/D112 2 6 6 4 3 8 69 262 9 116 1694 SHF4-12/D126 2 6 6 4 3 8 69 262 9 116 1694 SHF4-12/D143 2 6 6 4 3 8 69 262 9 116 1694 SHF4-16/D19 2 6 6 4 3 8 69 282 9 1146 1734 SHF4-16/D171 2 6 6 4 3 8 69 282 9 1146 1734 SHF4-2/D19 2 6 6 4 1 77 31 9 1194 1782 SHF4-2/D29 2 6 6 4 1 77 31 9 1194 1782 SHF4-2/D218 2 6 6 3 48 1 82 28 1 129 1797 SHF4-2/D233 2 6 6 3 48 1 92 33 12 129 1847 SHF4-2/D21 2 6 6 3 48 1 92 33 12 129 1847 SHF-12/D119 2 6 6 4 3 1 69 282 9 1238 1826 SHF-12/D13 2 6 6 4 3 1 69 282 9 1238 1826 SHF-12/D139 2 6 6 4 1 74 282 9 1238 1826 SHF-16/D18 2 6 6 4 1 77 31 9 1286 1874 SHF-16/D174 2 6 6 4 1 77 31 9 1286 1874 SHF-2/D197 2 6 6 3 48 1 82 31 1 136 1894 SHF-2/D29 2 6 6 3 48 1 82 31 12 136 1894 SHF-2/D224 2 6 6 3 48 1 92 33 12 131 1939 SHF-2/D237 2 6 6 3 48 1 97 38 13 141 1989 SHF-2/D2 2 6 6 3 48 1 97 38 13 141 1989 SHF6-16/D119 2 8 8 4 1 7 26 9 1323 1917 SHF6-16/D129 2 8 8 4 1 8 31 9 1373 1967 SHF6-16/D137 2 8 8 3 48 1 8 31 1 1373 1967 SHF6-16/D168 2 8 8 3 48 1 82 31 1 1373 1967 SHF6-16/D177 2 8 8 3 48 1 92 36 12 1423 217 SHF6-2/D192 2 8 8 3 48 1 92 33 12 1418 212 SHF6-2/D23 2 8 8 3 48 1 97 38 13 1468 262 SHF6-2/D21 2 8 8 3 48 1 97 38 13 1493 287 SHF6-2/D24 2 8 8 64 9 1 113 36 1 1473 267 SHF6-2/D2 2 8 8 64 9 1 113 36 1 1473 267 SHF8-16/D169 2 1 1 3 48 12 92 33 12 11 218 SHF8-16/D177 2 1 1 3 48 12 92 33 12 11 218 SHF8-16/D186 2 1 1 3 48 12 97 38 13 11 218 SHF8-2/D198 2 1 1 3 48 12 97 38 14 176 2183 SHF8-2/D21 2 1 1 64 9 12 19 36 1 16 2163 SHF8-2/D226 2 1 1 64 9 12 19 36 1 16 2163 SHF8-2/D237 2 1 1 64 9 12 118 36 1 191 2198 SHF8-2/D22 2 1 1 66 61 12 124 39 17 1616 2223 SHF8-2/D27 2 1 1 7 6 12 131 42 2 1646 223 Dimensions in mm. Tolerance ± 1 mm. gend_shf-en_h_td GEN..D/SHF 113

GEN..D/SHF 114

Fire-fighting booster sets EN 1284 MARKET SECTORS CIVIL, INDUSTRIAL APPLICATIONS Fixed fire-fighting systems. Automatic Sprinkler systems. GEN..1D/SHF Series SPECIFICATIONS GEN..D/SHF Flow up to 22 m 3 /h. Head up to 1 m. Panel supply power voltage: - Electric pump: 1 x 23V ± 1%. - Diesel engine pump: 1 x 23V ± 1%. Frequency: Hz. Voltage for controls outside panel: 12-24 Vac. Protection grade: - electric panel: IP4. Electric pumps maximum power 7 kw. Electric motor start : - Direct start for powers up to 22 kw included for electric pump. Diesel engine with battery start. Service pump in horizontal design: - SHF series. Electric jockey pump with vertical axis: - SV Series (motor protection grade IP). Maximum running pressure: 12 bar. 11

GEN..1D/SHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..D/SHF For the overall dimensions of the fuel tank and the starting batteries, see tables on pages 2-2. 116

GEN..1D/SHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..1D DRW N DNA DNP DNM A A1 B C D F G H I L N P Q SHF32-12/D121 1 R 2" Rp 1" R 1"1/2 33 22 28 9 8 22 362 14 4 9 126 113 187 SHF32-12/D136 1 R 2" Rp 1" R 1"1/2 33 22 28 9 8 22 362 14 4 9 126 113 187 SHF32-16/D1 1 R 2" Rp 1" R 1"1/2 33 22 28 88 8 22 382 14 4 9 124 13 1627 SHF32-16/D168 1 R 2" Rp 1" R 1"1/2 33 22 28 88 8 22 382 14 4 9 124 13 1627 SHF32-2/D188 1 R 2" Rp 1" R 1"1/2 33 22 28 88 8 22 36 14 4 9 124 11 162 SHF32-2/D24 1 R 2" Rp 1" R 1"1/2 4 22 28 1 8 22 36 14 47 11 136 11 162 SHF32-2/D222 1 R 2" Rp 1" R 1"1/2 4 22 28 12 1 22 38 14 47 11 14 1116 169 SHF32-2/D242 1 R 2" Rp 1" R 1"1/2 4 22 28 12 1 22 38 14 47 11 14 1116 169 SHF32-2/D26 1 R 2" Rp 1" R 1"1/2 4 22 28 91 1 22 38 14 47 11 129 1116 169 SHF4-12/D112 2 6 Rp 1" 6 33 22 28 88 8 22 362 14 4 9 124 126 1794 SHF4-12/D126 2 6 Rp 1" 6 33 22 28 88 8 22 362 14 4 9 124 126 1794 SHF4-12/D143 2 6 Rp 1" 6 33 22 28 88 8 22 362 14 4 9 124 126 1794 SHF4-16/D19 2 6 Rp 1" 6 33 22 28 88 8 22 382 14 4 9 124 1246 1834 SHF4-16/D171 2 6 Rp 1" 6 33 22 28 88 8 22 382 14 4 9 124 1246 1834 SHF4-2/D19 2 6 Rp 1" 6 4 22 28 98 1 22 41 14 47 11 136 1294 1882 SHF4-2/D29 2 6 Rp 1" 6 4 22 28 98 1 22 41 14 47 11 136 1294 1882 SHF4-2/D218 2 6 Rp 1" 6 39 23 28 97 1 22 38 14 47 11 13 139 1897 SHF4-2/D233 2 6 Rp 1" 6 39 23 28 117 1 22 43 14 47 11 1 139 1947 SHF4-2/D21 2 6 Rp 1" 6 39 23 28 117 1 22 43 14 47 11 1 139 1947 SHF-12/D119 2 6 Rp 1" 6 33 22 28 88 1 22 382 14 4 9 126 1338 1926 SHF-12/D13 2 6 Rp 1" 6 33 22 28 88 1 22 382 14 4 9 126 1338 1926 SHF-12/D139 2 6 Rp 1" 6 4 22 28 9 1 22 382 14 47 11 133 1338 1926 SHF-16/D18 2 6 Rp 1" 6 4 22 28 98 1 22 41 14 47 11 136 1386 1974 SHF-16/D174 2 6 Rp 1" 6 4 22 28 98 1 22 41 14 47 11 136 1386 1974 SHF-2/D197 2 6 Rp 1" 6 39 23 28 97 1 22 41 14 47 11 13 146 1994 SHF-2/D29 2 6 Rp 1" 6 39 23 28 97 1 22 41 14 47 11 13 146 1994 SHF-2/D224 2 6 Rp 1" 6 39 23 28 117 1 22 43 14 47 11 1 141 239 SHF-2/D237 2 6 Rp 1" 6 39 23 28 122 1 22 48 1 47 11 16 11 289 SHF-2/D2 2 6 Rp 1" 6 39 23 28 122 1 22 48 1 47 11 16 11 289 SHF6-16/D119 2 8 Rp 1" 8 4 22 28 97 1 22 36 14 47 11 13 1423 217 SHF6-16/D129 2 8 Rp 1" 8 4 22 28 12 1 22 41 14 47 11 14 1473 267 SHF6-16/D137 2 8 Rp 1" 8 39 23 28 11 1 22 41 14 47 11 148 1473 267 SHF6-16/D168 2 8 Rp 1" 8 39 23 28 97 1 22 41 14 47 11 13 1473 267 SHF6-16/D177 2 8 Rp 1" 8 39 23 28 117 1 22 46 14 47 11 1 123 2117 SHF6-2/D192 2 8 Rp 1" 8 39 23 28 117 1 22 43 14 47 11 1 118 2112 SHF6-2/D23 2 8 Rp 1" 8 39 23 28 122 1 22 48 1 47 11 16 168 2162 SHF6-2/D21 2 8 Rp 1" 8 39 23 28 122 1 22 48 1 47 11 16 193 2187 SHF6-2/D24 2 8 Rp 1" 8 46 38 18 127 1 24 48 17 3 137 1 193 2187 SHF6-2/D2 2 8 Rp 1" 8 46 38 18 127 1 24 48 17 3 137 1 193 2187 SHF8-16/D169 2 1 Rp 1" 1 39 23 28 117 12 22 43 14 47 11 17 161 228 SHF8-16/D177 2 1 Rp 1" 1 39 23 28 117 12 22 43 14 47 11 17 161 228 SHF8-16/D186 2 1 Rp 1" 1 39 23 28 122 12 22 48 1 47 11 162 161 228 SHF8-2/D198 2 1 Rp 1" 1 39 23 28 137 12 22 48 1 47 11 177 1676 2283 SHF8-2/D21 2 1 Rp 1" 1 27 28 144 12 24 48 17 3 13 184 1676 2283 SHF8-2/D226 2 1 Rp 1" 1 27 28 144 12 24 48 17 3 13 184 1676 2283 SHF8-2/D237 2 1 Rp 1" 1 26 28 1 12 24 48 17 3 13 19 1711 2318 SHF8-2/D22 2 1 Rp 1" 1 26 24 138 12 26 3 177 3 13 17 176 2363 SHF8-2/D27 2 1 Rp 1" 1 26 7 13 12 21 6 * 7 138 2 1786 2393 * Wall mounted control panel. gen1d_shf-en_g_td Dimensions in mm. Tolerance ± 1 mm. GEN..D/SHF 117

GEN..D/SHF 118

Fire-fighting booster sets EN 1284 MARKET SECTORS CIVIL, INDUSTRIAL APPLICATIONS Fixed fire-fighting systems. Automatic Sprinkler systems. Serie GEN..1D/SHF SPECIFICATIONS GEN..D/SHF Flow up to 44 m 3 /h. Head up to1 m. Panel supply power voltage: - Electric pump: 3 x 4V ± 1%. - Diesel engine pump: 1 x 23V ± 1%. Frequency: Hz. Voltage for controls outside panel: 12-24 Vac. Protection grade: - electric panel: IP4. Electric motor start : - Direct start for powers up to 22 kw included for pump (GEND...). - Star/delta start for higher powers (GENY... set). Diesel engine with battery start. Service pump in horizontal design: - SHF series (IP electric motor protection). Maximum running pressure: 12 bar. Electric pumps maximum power 7 kw. 119

GEN..1D/SHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..D/SHF For the overall dimensions of the fuel tank and the starting batteries, see tables on pages 2-2. 12

GEN..1D/SHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..1D DRW N DNA DNM A A1 B C D G H I L N P Q SHF32-12/7/D121 1 R 2" R 2" 32 31 24 87 8 362 14 47 11 123 119 199 SHF32-12/11/D136 1 R 2" R 2" 32 31 24 87 8 362 14 47 11 123 119 199 SHF32-16/1/D1 1 R 2" R 2" 32 31 24 8 8 382 14 47 11 121 19 1639 SHF32-16/22/D168 1 R 2" R 2" 32 31 24 8 8 382 14 47 11 121 19 1639 SHF32-2/3/D188 1 R 2" R 2" 32 31 24 8 8 36 14 47 11 121 17 1637 SHF32-2/4/D24 1 R 2" R 2" 38 3 24 96 8 36 14 7 13 132 17 1637 SHF32-2//D222 1 R 2" R 2" 38 3 24 12 1 38 14 7 13 14 1122 172 SHF32-2/7/D242 1 R 2" R 2" 38 3 24 12 1 38 14 7 13 14 1122 172 SHF32-2/11/D26 1 R 2" R 2" 42 37 28 99 1 38 14 61 14 137 1122 172 SHF4-12/11/D112 2 6 6 32 31 24 8 8 362 14 47 11 121 126 1794 SHF4-12/1/D126 2 6 6 32 31 24 8 8 362 14 47 11 121 126 1794 SHF4-12/22/D143 2 6 6 32 31 24 8 8 362 14 47 11 121 126 1794 SHF4-16/3/D19 2 6 6 32 31 24 8 8 382 14 47 11 121 1246 1834 SHF4-16/4/D171 2 6 6 32 31 24 8 8 382 14 47 11 121 1246 1834 SHF4-2//D19 2 6 6 38 3 24 94 1 41 14 7 13 132 1294 1882 SHF4-2/7/D29 2 6 6 38 3 24 94 1 41 14 7 13 132 1294 1882 SHF4-2/11A/D218 2 6 6 42 37 18 114 1 38 14 61 14 142 139 1897 SHF4-2/11/D233 2 6 6 42 37 28 122 1 43 14 61 14 16 139 1947 SHF4-2/1/D21 2 6 6 42 37 28 122 1 43 14 61 14 16 139 1947 SHF-12/22/D119 2 6 8 32 31 24 8 1 382 14 47 11 123 134 1939 SHF-12/3/D13 2 6 8 32 31 24 8 1 382 14 47 11 123 134 1939 SHF-12/4/D139 2 6 8 38 3 24 91 1 382 14 7 13 129 134 1939 SHF-16//D18 2 6 8 38 3 24 94 1 41 14 7 13 132 1393 1987 SHF-16/7/D174 2 6 8 38 3 24 94 1 41 14 7 13 132 1393 1987 SHF-2/11A/D197 2 6 8 42 37 13 18 1 41 14 61 14 146 1413 27 SHF-2/11/D29 2 6 8 42 37 2 18 1 41 14 61 14 146 1413 27 SHF-2/1/D224 2 6 8 41 37 28 122 1 43 14 61 14 16 148 22 SHF-2/18/D237 2 6 8 42 37 28 127 1 48 1 61 14 16 18 212 SHF-2/22/D2 2 6 8 42 37 28 127 1 48 1 61 14 16 18 212 SHF6-16/4/D119 2 8 1 38 3 24 92 1 36 14 7 13 13 143 242 SHF6-16//D129 2 8 1 38 3 24 97 1 41 14 7 13 13 148 292 SHF6-16/7/D137 2 8 1 42 37 24 16 1 41 14 7 136 144 148 292 SHF6-16/11A/D168 2 8 1 42 37 18 114 1 41 14 61 14 142 148 292 SHF6-16/11/D177 2 8 1 41 37 28 122 1 46 14 61 14 16 13 2142 SHF6-2/1/D192 2 8 1 41 37 28 122 1 43 14 61 14 16 13 2137 SHF6-2/18/D23 2 8 1 42 37 28 127 1 48 1 61 14 16 18 2187 SHF6-2/22/D21 2 8 1 42 37 28 127 1 48 1 61 14 16 16 2212 SHF6-2/3/D24 2 8 1 48 4 29 14 1 48 17 73 166 184 16 2212 SHF6-2/37/D2 2 8 1 48 4 29 14 1 48 17 73 166 184 16 2212 SHF8-16/11/D169 2 1 12 41 37 28 122 12 43 14 61 14 163 1614 2234 SHF8-16/1/D177 2 1 12 41 37 28 122 12 43 14 61 14 163 1614 2234 SHF8-16/18/D186 2 1 12 42 37 28 127 12 48 1 61 14 168 1664 2284 SHF8-2/22/D198 2 1 12 42 37 33 127 12 48 1 61 14 173 1689 239 SHF8-2/3/D21 2 1 12 48 4 3 141 12 48 17 73 166 184 1689 239 SHF8-2/37/D226 2 1 12 48 4 3 141 12 48 17 73 166 184 1689 239 SHF8-2/4/D237 2 1 12 48 4 32 14 12 48 17 73 166 189 1724 2344 SHF8-2//D22 2 1 12 48 4 3 1 12 3 177 73 166 198 1769 2389 SHF8-2/7/D27 2 1 12 14 12 6 * 8 19 21 1799 2419 * Wall mounted control panel. gen1d_shf-en_f_td Dimensions in mm. Tolerance ± 1 mm. GEN..D/SHF 121

GEN..D/SHF 122

Fire-fighting booster sets EN 1284 MARKET SECTORS CIVIL, INDUSTRIAL APPLICATIONS Fixed fire-fighting systems. Automatic Sprinkler systems. GEN..11D/SHF Series SPECIFICATIONS GEN..D/SHF Flow up to 44 m 3 /h. Head up to 1 m. Panel supply power voltage: - Electric pump: 3 x 4V ± 1%. - Diesel engine pump: 1 x 23V ± 1%. Frequency: Hz. Voltage for controls outside panel: 12-24 Vac. Protection grade: - electric panel: IP4. Electric pumps maximum power 7 kw. Electric motor start : - Direct start for powers up to 22 kw included for pump (GEND...). - Star/delta start for higher powers (GENY... set). Diesel engine with battery start. Service pump in horizontal design: - SHF series (IP electric motor protection). Electric jockey pump with vertical axis: - SV Series (motor protection grade IP). Maximum running pressure: 12 bar. 123

GEN..11D/SHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..D/SHF For the overall dimensions of the fuel tank and the starting batteries, see tables on pages 2-2. 124

GEN..11D/SHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS EN 1284 GEN..11D DRW DNA DNP DNM A A1 B C D F G H I I1 L N P Q N SHF32-12/7/D121 1 R 2" Rp 1" R 2" 3 29 24 9 8 22 362 14 4 4 14 122 119 199 SHF32-12/11/D136 1 R 2" Rp 1" R 2" 3 29 24 9 8 22 362 14 4 4 14 122 119 199 SHF32-16/1/D1 1 R 2" Rp 1" R 2" 3 29 24 8 8 22 382 14 4 4 14 117 19 1639 SHF32-16/22/D168 1 R 2" Rp 1" R 2" 3 29 24 8 8 22 382 14 4 4 14 117 19 1639 SHF32-2/3/D188 1 R 2" Rp 1" R 2" 3 29 24 8 8 22 36 14 4 4 14 117 17 1637 SHF32-2/4/D24 1 R 2" Rp 1" R 2" 4 37 24 1 8 22 36 14 47 43 168 132 17 1637 SHF32-2//D222 1 R 2" Rp 1" R 2" 3 37 24 1 1 22 38 14 47 47 168 134 1122 172 SHF32-2/7/D242 1 R 2" Rp 1" R 2" 3 37 24 1 1 22 38 14 47 47 168 134 1122 172 SHF32-2/11/D26 1 R 2" Rp 1" R 2" 3 37 28 112 1 22 38 14 47 47 168 1 1122 172 SHF4-12/11/D112 2 6 Rp 1" 6 3 29 24 8 8 22 362 14 4 4 14 117 126 1794 SHF4-12/1/D126 2 6 Rp 1" 6 3 29 24 8 8 22 362 14 4 4 14 117 126 1794 SHF4-12/22/D143 2 6 Rp 1" 6 3 29 24 8 8 22 362 14 4 4 14 117 126 1794 SHF4-16/3/D19 2 6 Rp 1" 6 3 29 24 8 8 22 382 14 4 4 14 117 1246 1834 SHF4-16/4/D171 2 6 Rp 1" 6 3 29 24 8 8 22 382 14 4 4 14 117 1246 1834 SHF4-2//D19 2 6 Rp 1" 6 4 37 24 94 1 22 41 14 47 43 168 128 1294 1882 SHF4-2/7/D29 2 6 Rp 1" 6 4 37 24 94 1 22 41 14 47 43 168 128 1294 1882 SHF4-2/11A/D218 2 6 Rp 1" 6 36 3 18 99 1 22 38 14 47 47 167 127 139 1897 SHF4-2/11/D233 2 6 Rp 1" 6 37 38 28 99 1 22 43 14 47 47 171 137 139 1947 SHF4-2/1/D21 2 6 Rp 1" 6 37 38 28 99 1 22 43 14 47 47 171 137 139 1947 SHF-12/22/D119 2 6 Rp 1" 8 3 29 24 8 1 22 382 14 4 4 14 119 134 1939 SHF-12/3/D13 2 6 Rp 1" 8 3 29 24 8 1 22 382 14 4 4 14 119 134 1939 SHF-12/4/D139 2 6 Rp 1" 8 4 37 24 1 1 22 382 14 47 43 168 134 134 1939 SHF-16//D18 2 6 Rp 1" 8 4 37 24 94 1 22 41 14 47 43 168 128 1393 1987 SHF-16/7/D174 2 6 Rp 1" 8 4 37 24 94 1 22 41 14 47 43 168 128 1393 1987 SHF-2/11A/D197 2 6 Rp 1" 8 38 34 13 89 1 22 41 14 47 47 168 112 1413 27 SHF-2/11/D29 2 6 Rp 1" 8 38 34 2 89 1 22 41 14 47 47 168 12 1413 27 SHF-2/1/D224 2 6 Rp 1" 8 37 38 28 99 1 22 43 14 47 47 171 137 148 22 SHF-2/18/D237 2 6 Rp 1" 8 4 39 28 99 1 22 48 1 47 47 174 137 18 212 SHF-2/22/D2 2 6 Rp 1" 8 4 39 28 99 1 22 48 1 47 47 174 137 18 212 SHF6-16/4/D119 2 8 Rp 1" 1 4 37 24 92 1 22 36 14 47 43 168 126 143 242 SHF6-16//D129 2 8 Rp 1" 1 39 36 24 97 1 22 41 14 47 43 166 131 148 292 SHF6-16/7/D137 2 8 Rp 1" 1 38 33 24 16 1 22 41 14 47 43 162 14 148 292 SHF6-16/11A/D168 2 8 Rp 1" 1 36 3 18 99 1 22 41 14 47 47 167 127 148 292 SHF6-16/11/D177 2 8 Rp 1" 1 37 38 28 99 1 22 46 14 47 47 171 137 13 2142 SHF6-2/1/D192 2 8 Rp 1" 1 37 38 28 99 1 22 43 14 47 47 171 137 13 2137 SHF6-2/18/D23 2 8 Rp 1" 1 4 39 28 99 1 22 48 1 47 47 174 137 18 2187 SHF6-2/22/D21 2 8 Rp 1" 1 4 39 28 99 1 22 48 1 47 47 174 137 16 2212 SHF6-2/3/D24 2 8 Rp 1" 1 47 43 29 116 1 19 48 17 3 49 192 1 16 2212 SHF6-2/37/D2 2 8 Rp 1" 1 47 43 29 116 1 19 48 17 3 49 192 1 16 2212 SHF8-16/11/D169 2 1 Rp 1" 12 37 38 28 99 12 22 43 14 47 47 171 14 1614 2234 SHF8-16/1/D177 2 1 Rp 1" 12 37 38 28 99 12 22 43 14 47 47 171 14 1614 2234 SHF8-16/18/D186 2 1 Rp 1" 12 4 39 28 99 12 22 48 1 47 47 174 14 1664 2284 SHF8-2/22/D198 2 1 Rp 1" 12 4 39 33 99 12 22 48 1 47 47 174 14 1689 239 SHF8-2/3/D21 2 1 Rp 1" 12 47 43 3 112 12 19 48 17 3 49 192 1 1689 239 SHF8-2/37/D226 2 1 Rp 1" 12 47 43 3 112 12 19 48 17 3 49 192 1 1689 239 SHF8-2/4/D237 2 1 Rp 1" 12 47 39 32 12 12 19 48 17 3 49 188 16 1724 2344 SHF8-2//D22 2 1 Rp 1" 12 48 4 3 127 12 21 3 177 3 3 2 17 1769 2389 SHF8-2/7/D27 2 1 Rp 1" 12 8 4 137 12 21 6 * 7 7 226 2 1799 2419 * Wall mounted control panel. gen11d_shf-en_h_td Dimensions in mm. Tolerance ± 1 mm. GEN..D/SHF 12

GEN..D/SHF 126

GEN..D/SHF SERIES OF BOOSTER SETS (POSITIVE SUCTION HEAD) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT SH 32-12 29 [rpm] ISO 996 - Annex A SH 32-16 29 [rpm] ISO 996 - Annex A 2 4 6 8 1 Q [Imp gpm] 2 4 6 8 1 Q [Imp gpm] 2 4 6 8 1 12 Q [US gpm],2,8 Hc [m] H [ft],2,6 2 4 6 8 1 12 Q [US gpm],2,8 Hc [m] H [ft],2,6,1,1,4,1,1,4,,2,,2, 6,, 8, 2 1 6 2 4 NPSHr [m] 2 1 NPSHr [ft] NPSHr [m] 4 32-16/1 φ 1 6-16/1 32-16/1 Ø φ 178 164 1 1 NPSHr [ft] 2 1 1 2 2 Q [m 3 /h] 3 1 2 3 4 Q [l/min] 7617_A_CH 1 1 2 2 Q [m 3 3 /h] 1 2 3 4 Q [l/min] 7618_A_CH SH 32-2 29 [rpm] ISO 996 - Annex A 2 4 6 8 1 Q [Imp gpm] 2 4 6 8 1 12 Q [US gpm],2,8 Hc [m] H [ft],2,6 SH 32-2 29 [rpm] ISO 996 - Annex A 2 4 6 8 1 Q [Imp gpm] 2 4 6 8 1 12 Q [US gpm],2,8 Hc [m] H [ft],2,6 GEN..D/SHF,1,1,4,1,1,4,,2,,2, 8, 2, 8, 2 6 2 6 32-2/ φ 222 2 NPSHr [m] 4 32-2/3 φ 188 32-2/4 φ 24 6-16/1 Ø 178 1 1 NPSHr [ft] NPSHr [m] 4 32-2/11 φ 26 32-2/7 φ 242 6-16/1 Ø 178 1 1 NPSHr [ft] 2 2 1 1 2 2 Q [m 3 3 /h] 1 2 3 4 Q [l/min] 7619_A_CH 1 1 2 2 Q [m 3 3 /h] 1 2 3 4 Q [l/min] 762_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 127

GEN..D/SHF SERIES OF BOOSTER SETS (POSITIVE SUCTION HEAD) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT SH 4-12 29 [rpm] ISO 996 - Annex A SH 4-16 29 [rpm] ISO 996 - Annex A 1 1 Q [Imp gpm] 1 1 Q [Imp gpm] Hc [m] 1 1 2,2,2 Q [US gpm],8,6 H [ft] 1 1 2 Q [US gpm],2,8 Hc [m] H [ft],2,6,1,1,4,1,1,4,,2,,2, 8, 2, 8, 2 6 2 6 2 NPSHr [m] 4 1 1 NPSHr [ft] NPSHr [m] 4 1 1 NPSHr [ft] 2 2 1 2 3 4 Q [m 3 /h] 1 2 3 4 6 7 Q 8 [l/min] 7621_A_CH 1 2 3 4 Q [m 3 /h] 6 1 2 3 4 6 7 Q 8 [l/min] 7622_A_CH GEN..D/SHF SH 4-2 29 [rpm] ISO 996 - Annex A 1 1 Q [Imp gpm] 1 1 2 Q [US gpm],2,8 Hc [m] H [ft],2,6 SH 4-2 29 [rpm] ISO 996 - Annex A 1 1 2 Q [Imp gpm] 1 1 2 Q [US 2gpm],2,8 Hc [m] H [ft],2,6,1,1,4,1,1,4,,2,,2, 8, 2, 8, 2 6 2 6 2 NPSHr [m] 4 1 1 NPSHr [ft] NPSHr [m] 4 4-2/11A φ 216 6-16/1 Ø 178 1 1 NPSHr [ft] 2 2 4-2/1 φ 21 4-2/11 φ 233 1 2 3 4 Q [m 3 /h] 6 1 2 3 4 6 7 Q 8 [l/min] 7623_A_CH 1 2 3 4 Q [m 3 6 /h] 2 4 6 8 Q [l/min] 1 7624_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 128

GEN..D/SHF SERIES OF BOOSTER SETS (POSITIVE SUCTION HEAD) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT SH - 12 29 [rpm] ISO 996 - Annex A SH - 16 29 [rpm] ISO 996 - Annex A 1 2 3 Q [Imp gpm] 1 2 3 Q [Imp gpm] 1 2 3 4 Q [US gpm],2,8 Hc [m] H [ft],2,6 1 2 3 4 Q [US gpm],2,8 Hc [m] H [ft],2,6,1,1,4,1,1,4,,2,,2, 8, 2, 1, 3 6 2 8 2 NPSHr [m] 4-12/22 φ 119-12/4 φ 139-12/3 φ 13 6-16/1 Ø 178 1 1 NPSHr [ft] NPSHr [m] 6 4-16/ φ 119 6-16/1-16/7 Ø 178 φ 174 2 1 NPSHr [ft] 2 2 1 2 4 6 8 Q [m1 3 /h] 2 4 6 8 1 12 14 Q 16 [l/min] 762_A_CH 2 4 6 8 Q [m1 3 /h] 2 4 6 8 1 12 14 Q 16 [l/min] 7626_A_CH Hc [m] SH - 2 29 [rpm] ISO 996 - Annex A 1 2 3 Q [Imp gpm] 1 2 3 4 Q [US gpm],3,2,8,2,6 H [ft] Hc [m] SH - 2 29 [rpm] ISO 996 - Annex A 1 2 3 Q [Imp gpm] 1 2 3 4 Q [US gpm],3,2,8,2,6 H [ft] GEN..D/SHF,1,1,4,4,1,1,,2,,2, 1,, 1, 3 3 8 2 8 2 6-2/11A φ 197 2 6 2 NPSHr [m] 4-2/11 φ 29 6-16/1 Ø 178 1 NPSHr [ft] NPSHr [m] 4-2/1 φ 224 6-16/1 Ø 178 1 NPSHr [ft] 1-2/22 φ 2-2/18 φ 237 1 2 2 2 4 6 8 Q [m1 3 /h] 2 4 6 8 1 12 14 Q 16 [l/min] 7627_A_CH 2 4 6 8 Q [m1 3 /h] 2 4 6 8 1 12 14 Q 16 [l/min] 7628_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 129

GEN..D/SHF SERIES OF BOOSTER SETS (POSITIVE SUCTION HEAD) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT SH 6-16 29 [rpm] ISO 996 - Annex A SH 6-16 29 [rpm] ISO 996 - Annex A 1 2 3 4 Q [Imp gpm] 1 2 3 4 Q [US 6 gpm],3 1 2 3 4 Q [Imp gpm] 1 2 3 4 Q [US 6 gpm],4 Hc [m],2,8 H [ft] Hc [m],3 1,2 1, H [ft],2,6,8,1,4,2,6,1,,2,1,4,2, 1,, 1, 3 3 8 2 8 2 6 6-16/22 φ 119 2 6 2 NPSHr [m] 4 6-16/4 φ 139 6-16/3 φ 13 6-16/1 Ø 178 1 NPSHr [ft] NPSHr [m] 4 6-16/1 Ø 178 1 NPSHr [ft] 1 1 2 2 6-16/11 φ 177 6-16/11A φ 168 2 4 6 8 1 12 Q [m14 3 /h] 2 4 6 8 1 12 14 16 18 2 Q 22 [l/min] 7629_A_CH 2 4 6 8 1 12 Q [m14 3 /h] 2 4 6 8 1 12 14 16 18 2 Q 22 [l/min] 763_A_CH GEN..D/SHF Hc [m] SH 6-2 29 [rpm] ISO 996 - Annex A 1 2 3 4 Q [Imp gpm] 1 2 3 4 Q [US 6 gpm],4 1,2,3 1,,8 H [ft] Hc [m] SH 6-2 29 [rpm] ISO 996 - Annex A 1 2 3 4 Q [Imp gpm] 1 2 3 4 6 Q [US gpm] 7,6, 1,,4 H [ft],2,6,3 1,,1,4,2,,2,1, 1,, 1, 3 3 8 2 8 2 NPSHr [m] 6 4 6-2/1 φ 192 6-16/1 Ø 178 2 1 NPSHr [ft] NPSHr [m] 6 4 6-2/3 φ 24 6-2/37 φ 2 6-16/1 Ø 178 2 1 NPSHr [ft] 6-2/22 φ 21 1 1 2 6-2/18 φ 23 2 2 4 6 8 1 12 Q [m14 3 /h] 2 4 6 8 1 12 14 16 18 2 Q 22 [l/min] 7631_A_CH 2 4 6 8 1 12 14 Q [m16 3 /h] 1 1 2 2 Q [l/min] 7632_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 13

GEN..D/SHF SERIES OF BOOSTER SETS (POSITIVE SUCTION HEAD) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT SH 8-16 29 [rpm] ISO 996 - Annex A SH 8-2 29 [rpm] ISO 996 - Annex A 2 4 6 8 Q [Imp gpm] 2 4 6 8 1 Q [Imp gpm] 2 4 6 8 1 Q [US gpm],4 2 4 6 8 1 12 Q [US gpm],4 Hc [m] 1,2 H [ft] Hc [m] H [ft],3 1,,3 1,,8,2,6,2 1,,1,4,1,,2, 1,, 1, 3 3 8 2 8 2 6 8-16/1 φ 169x1 2 6 8-2/22 φ 198 2 NPSHr [m] 4 6-16/1 Ø 178 1 NPSHr [ft] NPSHr [m] 4 8-2/37 φ 22 8-2/3 6-16/1 φ 21 Ø 178 1 NPSHr [ft] 8-16/18 φ 186 8-16/1 φ 177 1 1 2 2 1 1 2 Q [m2 3 /h] 1 2 3 Q 4 [l/min] 7633_A_CH 1 1 2 2 Q [m3 3 /h] 1 2 3 4 Q [l/min] 7634_A_CH Hc [m] SH 8-2 29 [rpm] ISO 996 - Annex A 2 4 6 8 Q [Imp gpm] 2 4 6 8 1 Q [US gpm],4 1,2,3 1,,8 H [ft] GEN..D/SHF,2,6,1,4,2, 1, 3 8 2 6 2 NPSHr [m] 4 6-16/1 Ø 178 1 NPSHr [ft] 1 2 1 1 2 Q [m2 3 /h] 1 2 3 4 Q [l/min] 763_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 131

GEN..D/SHF SERIES OF BOOSTER SETS (SUCTION LIFT) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT SH 32-12 29 [rpm] ISO 996 - Annex A SH 32-16 29 [rpm] ISO 996 - Annex A 2 4 6 8 1 Q [Imp gpm] 2 4 6 8 1 12 Q [US gpm],4 2 4 6 8 1 Q [Imp gpm] 2 4 6 8 1 12 Q [US gpm],6 Hc [m] H [ft] Hc [m], H [ft],3 1, 1,,4,2,3 1,,,2,1,,1, 6,, 8, 2 1 6 2 4 NPSHr [m] 2 1 NPSHr [ft] NPSHr [m] 4 32-16/1 φ 1 6-16/1 32-16/1 Ø φ 178 164 1 1 NPSHr [ft] 2 1 1 2 2 Q [m 3 /h] 3 1 2 3 4 Q [l/min] 76497_A_CH 1 1 2 2 Q [m 3 3 /h] 1 2 3 4 Q [l/min] 76498_A_CH GEN..D/SHF Hc [m] SH 32-2 29 [rpm] ISO 996 - Annex A 2 4 6 8 1 Q [Imp gpm] 2 4 6 8 1 12 Q [US gpm],6, 1,,4 H [ft] Hc [m] SH 32-2 29 [rpm] ISO 996 - Annex A 2 4 6 8 1 Q [Imp gpm] 2 4 6 8 1 12 Q [US gpm],6, 1,,4 H [ft],3 1,,3 1,,2,2,,,1,1, 8, 2, 8, 2 6 2 6 32-2/ φ 222 2 NPSHr [m] 4 32-2/3 φ 188 32-2/4 φ 24 6-16/1 Ø 178 1 1 NPSHr [ft] NPSHr [m] 4 32-2/11 φ 26 32-2/7 φ 242 6-16/1 Ø 178 1 1 NPSHr [ft] 2 2 1 1 2 2 Q [m 3 3 /h] 1 2 3 4 Q [l/min] 76499_A_CH 1 1 2 2 Q [m 3 3 /h] 1 2 3 4 Q [l/min] 76_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 132

GEN..D/SHF SERIES OF BOOSTER SETS (SUCTION LIFT) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT SH 4-12 29 [rpm] ISO 996 - Annex A SH 4-16 29 [rpm] ISO 996 - Annex A 1 1 Q [Imp gpm] 1 1 Q [Imp gpm] 1 1 2,6 Q [US gpm] 1 1 2 Q [US gpm],6 Hc [m], H [ft] Hc [m], H [ft] 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 8, 2, 8, 2 6 2 6 2 NPSHr [m] 4 1 1 NPSHr [ft] NPSHr [m] 4 1 1 NPSHr [ft] 2 2 1 2 3 4 Q [m 3 /h] 1 2 3 4 6 7 Q 8 [l/min] 761_A_CH 1 2 3 4 Q [m 3 /h] 6 1 2 3 4 6 7 Q 8 [l/min] 762_A_CH Hc [m] SH 4-2 29 [rpm] ISO 996 - Annex A 1 1 Q [Imp gpm] 1 1 2 Q [US gpm],6, 1,,4 H [ft] Hc [m] SH 4-2 29 [rpm] ISO 996 - Annex A 1 1 2 Q [Imp gpm] 1 1 2 Q [US 2gpm],6, 1,,4 H [ft] GEN..D/SHF,3 1,,3 1,,2,2,,,1,1, 8, 2, 8, 2 6 2 6 2 NPSHr [m] 4 1 1 NPSHr [ft] NPSHr [m] 4 4-2/11A φ 216 6-16/1 Ø 178 1 1 NPSHr [ft] 2 2 4-2/1 φ 21 4-2/11 φ 233 1 2 3 4 Q [m 3 /h] 6 1 2 3 4 6 7 Q 8 [l/min] 763_A_CH 1 2 3 4 Q [m 3 6 /h] 2 4 6 8 Q [l/min] 1 764_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 133

GEN..D/SHF SERIES OF BOOSTER SETS (SUCTION LIFT) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT SH - 12 29 [rpm] ISO 996 - Annex A SH - 16 29 [rpm] ISO 996 - Annex A 1 2 3 Q [Imp gpm] 1 2 3 Q [Imp gpm] 1 2 3 4 Q [US gpm],6 1 2 3 4 Q [US gpm],6 Hc [m], H [ft] Hc [m], H [ft] 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 8, 2, 1, 3 6 2 8 2 NPSHr [m] 4-12/22 φ 119-12/4 φ 139-12/3 φ 13 6-16/1 Ø 178 1 1 NPSHr [ft] NPSHr [m] 6 4-16/ φ 119 6-16/1-16/7 Ø 178 φ 174 2 1 NPSHr [ft] 2 2 1 2 4 6 8 Q [m1 3 /h] 2 4 6 8 1 12 14 Q 16 [l/min] 76_A_CH 2 4 6 8 Q [m1 3 /h] 2 4 6 8 1 12 14 Q 16 [l/min] 766_A_CH GEN..D/SHF Hc [m] SH - 2 29 [rpm] ISO 996 - Annex A 1 2 3 Q [Imp gpm] 1 2 3 4 Q [US gpm],6, 1,,4 H [ft] Hc [m] SH - 2 29 [rpm] ISO 996 - Annex A 1 2 3 Q [Imp gpm] 1 2 3 4 Q [US gpm],6, 1,,4 H [ft],3 1,,3 1,,2,2,,,1,1, 1,, 1, 3 3 8 2 8 2 6-2/11A φ 197 2 6 2 NPSHr [m] 4-2/11 φ 29 6-16/1 Ø 178 1 NPSHr [ft] NPSHr [m] 4-2/1 φ 224 6-16/1 Ø 178 1 NPSHr [ft] 1-2/22 φ 2-2/18 φ 237 1 2 2 2 4 6 8 Q [m1 3 /h] 2 4 6 8 1 12 14 Q 16 [l/min] 767_A_CH 2 4 6 8 Q [m1 3 /h] 2 4 6 8 1 12 14 Q 16 [l/min] 768_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 134

GEN..D/SHF SERIES OF BOOSTER SETS (SUCTION LIFT) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT SH 6-16 29 [rpm] ISO 996 - Annex A SH 6-16 29 [rpm] ISO 996 - Annex A 1 2 3 4 Q [Imp gpm] 1 2 3 4 Q [US 6 gpm],6 1 2 3 4 Q [Imp gpm] 1 2 3 4 Q [US 6 gpm],6 Hc [m], H [ft] Hc [m], H [ft] 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, 3 3 8 2 8 2 6 6-16/22 φ 119 2 6 2 NPSHr [m] 4 6-16/4 φ 139 6-16/3 φ 13 6-16/1 Ø 178 1 NPSHr [ft] NPSHr [m] 4 6-16/1 Ø 178 1 NPSHr [ft] 1 1 2 2 6-16/11 φ 177 6-16/11A φ 168 2 4 6 8 1 12 Q [m14 3 /h] 2 4 6 8 1 12 14 16 18 2 Q 22 [l/min] 761_A_CH 2 4 6 8 1 12 Q [m14 3 /h] 2 4 6 8 1 12 14 16 18 2 Q 22 [l/min] 7611_A_CH Hc [m] SH 6-2 29 [rpm] ISO 996 - Annex A 1 2 3 4 Q [Imp gpm] 1 2 3 4 Q [US 6 gpm],6, 1,,4 H [ft] Hc [m] SH 6-2 29 [rpm] ISO 996 - Annex A 1 2 3 4 Q [Imp gpm] 1 2 3 4 6 Q [US gpm] 7,6, 1,,4 H [ft] GEN..D/SHF,3 1,,3 1,,2,2,,,1,1, 1,, 1, 3 3 8 2 8 2 NPSHr [m] 6 4 6-2/1 φ 192 6-16/1 Ø 178 2 1 NPSHr [ft] NPSHr [m] 6 4 6-2/3 φ 24 6-2/37 φ 2 6-16/1 Ø 178 2 1 NPSHr [ft] 6-2/22 φ 21 1 1 2 6-2/18 φ 23 2 2 4 6 8 1 12 Q [m14 3 /h] 2 4 6 8 1 12 14 16 18 2 Q 22 [l/min] 7612_A_CH 2 4 6 8 1 12 14 Q [m16 3 /h] 1 1 2 2 Q [l/min] 7613_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 13

GEN..D/SHF SERIES OF BOOSTER SETS (SUCTION LIFT) Hc PRESSURE SURE DROP CURVE IN SUCTION KIT SH 8-16 29 [rpm] ISO 996 - Annex A SH 8-2 29 [rpm] ISO 996 - Annex A 2 4 6 8 Q [Imp gpm] 2 4 6 8 1 Q [Imp gpm] 2 4 6 8 1 Q [US gpm],6 2 4 6 8 1 12 Q [US gpm],6 Hc [m], H [ft] Hc [m], H [ft] 1, 1,,4,4,3 1,,3 1,,2,2,,,1,1, 1,, 1, 3 3 8 2 8 2 6 8-16/1 φ 169x1 2 6 8-2/22 φ 198 2 NPSHr [m] 4 6-16/1 Ø 178 1 NPSHr [ft] NPSHr [m] 4 8-2/37 φ 22 8-2/3 6-16/1 φ 21 Ø 178 1 NPSHr [ft] 8-16/18 φ 186 8-16/1 φ 177 1 1 2 2 1 1 2 Q [m2 3 /h] 1 2 3 Q 4 [l/min] 7614_A_CH 1 1 2 2 Q [m3 3 /h] 1 2 3 4 Q [l/min] 761_A_CH GEN..D/SHF Hc [m] SH 8-2 29 [rpm] ISO 996 - Annex A 2 4 6 8 Q [Imp gpm] 2 4 6 8 1 Q [US gpm],6, 1,,4 H [ft],3 1,,2,,1, 1, 3 8 2 6 2 NPSHr [m] 4 6-16/1 Ø 178 1 NPSHr [ft] 1 2 1 1 2 Q [m2 3 /h] 1 2 3 4 Q [l/min] 7616_A_CH The declared performance value are valid for liquids with density ρ = 1. Kg/dm 3 and kinematic viscosity ν = 1 mm 2 /sec. The NPSHr values required for the service pump were obtained in the laboratory. When using them for EN 1284 for fire-fighting systems, increase the value by 1 m. Hc: Pressure drop curve in suction kit. 136

ACCESSORIES SORIES ACCESSORIES SORIES 137

DIAPHRAGM TANKS The booster sets are ready for installation, directly on the manifold, of 24-litre diaphragm tanks, one for each pump. The sets are also equipped with caps to close off the unused couplings. Larger tanks can also be connected to the unused end of the discharge manifold. For proper sizing of the tank please refer to the technical appendix. Kit featuring the following accessories are available on request: diaphragm tank; on-off ball valve; operating instructions; packaging. DIMENSIONI KIT VASI A MEMBRANA DIAPHRAGM TANK KIT Volume PN DIMENSIONS (mm) Materials Litres bar ø A B Valve Diaphragm Vessel Valve 8 8 2 39 1" FF EPDM Painted steel Nickel-plated brass 24 8 27 1" FF EPDM Painted steel Nickel-plated brass 24 1 27 1" FF EPDM Painted steel Nickel-plated brass 24 16 27 1" FF EPDM Painted steel Nickel-plated brass 24 1 27 7 1" FF Butyl Stainless steel AISI 316 stainless steel 2 2 27 1" FF EPDM Painted steel Nickel-plated brass COUNTERFLANGE KIT Counterflange coupling kits made of zinc-plated or stainless steel are available on request. The counterflange kits are equipped with: - N. 2 flanges. - gasket and bolts/screws. THREADED COUNTERFLANGES DIMENSIONI KIT CONTROFLANGE TONDE FI Gcom-vmb-en_c_td ACCESSORIES SORIES KIT DIMENSIONS (mm) HOLES TYPE DN ø C ø A B ø D H ø F N PN 2" Rp 2 12 16 16 24 18 4 2 2" ½ 6 Rp 2 ½ 14 16 18 23 18 4 16 3" 8 Rp 3 16 17 2 27 18 8 16 Gcom-ctf-tonde-f-en_a_td DIMENSIONI KIT CONTROFLANGE TONDE A SALDARE WELD-ON COUNTERFLANGES KIT DIMENSIONS (mm) HOLES TYPE DN ø C ø A B ø D ø F N PN 2" 61 12 19 16 18 4 16 2"1/2 6 77 14 2 18 18 4 16 3" 8 9 16 2 2 18 8 16 4" 1 116 18 22 22 18 8 16 " 12 141, 21 22 2 18 8 16 6" 1 17, 24 24 28 22 8 16 8" 2 221, 29 26 34 22 12 16 1" 2 276, 3 29 4 26 12 16 12" 3 327, 41 32 46 26 12 16 Gcom-ctf-tonde-s-en_c_td 138

ACCESSORIES SORIES FOR BOOSTER SETS SUCTION SIDE KIT The EN 1284 fire-fighting booster sets are supplied without valves and stubs on the suction side of the service pump and can be completed with suitable kits that depend on legal standards. These requirements are expressed by EN 1284 (chapter 1. and chapter 1.6) and are connected with the maximum speed value of the water in the pipes, their minimum section and type of installation - suction lift or positive suction head. To provide for one suction kit for each duty pump. The suction side kit are equipped with: - Anti-vibration joint to attach to the pump inlet. - Eccentric cone or flanged stub pipe. - Vacuum pressure gauge. - On/off butterfly valve (optional in case of positive suction head installation) with lever handle for diameters up to DN1, butterfly valve with handwheel and reduction manual gear for DN12 and higher. Device for monitoring ON/OFF status included. Electrical connections by customer. (Valve lock kit available on request). - Weld-on flange. The following table summarises the pump type installed on the fire-fighting sets and the kit that corresponds to the installation type. ACCESSORIES SORIES 139

GEN../ SERIES OF FIRE-FIGHTING BOOSTER SETS SUCTION SIDE KIT DIMENSIONS TABLE ACCESSORIES SORIES SUCTION DIMENSIONS KIT L (mm) TYPE DNS PN DNA PN H (mm) Type 1 Type 2 X 32 16 32 16 9 243 283 X 4 16 4 16 6 243 283 6 X 32 6 16 32 16 17 269 312 6 X 4 6 16 4 16 14 2 298 6 X 6 16 16 8 266 39 8 X 32 8 16 32 16 23 34 347 8 X 4 8 16 4 16 2 288 331 8 X 8 16 16 14 266 39 8 X 6 8 16 6 16 6 277 32 1 X 4 1 16 4 16 33 362 411 1 X 1 16 16 27 34 389 1 X 6 1 16 6 16 19 37 36 1 X 8 1 16 8 16 13 296 34 12 X 12 16 16 4 41 463 12 X 6 12 16 6 16 32 377 43 12 X 8 12 16 8 16 2 37 41 12 X 1 12 16 1 16 13 33 36 1 X 6 1 16 6 16 46 46 13 1 X 8 1 16 8 16 4 44 493 1 X 1 1 16 1 16 27 377 43 1 X 12 1 16 12 16 14 3 48 2 X 8 2 1 8 16 6 79 636 2 X 1 2 1 1 16 2 16 73 2 X 12 2 1 12 16 4 482 39 2 X 1 2 1 1 16 2 41 472 2 X 1 2 1 1 16 79 672 737 2 X 12 2 1 12 16 67 637 72 2 X 1 2 1 1 16 2 7 63 3 X 12 3 1 12 16 92 774 849 3 X 1 3 1 1 16 78 77 782 3 X 1 3 1 1 16 94 798 873 4 X 1 4 1 1 16 119 946 14 Dimensions in mm. Tolerance ± 1 mm. kit-asp2-en_a_td 14

GEN../FHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS SUCTION SIDE KIT DIMENSIONS TABLE SUCTION LIFT POSITIVE SUCTION HEAD RISK SUCTION RISK SUCTION RISK SUCTION RISK SUCTION PUMP CLASS * KIT CLASS * KIT CLASS * KIT CLASS * KIT TYPE TYPE TYPE TYPE FHF 32-12/7 LH 6 X - - LH 8 X - - FHF 32-12/11 LH 6 X - - LH 8 X - - FHF 32-16/1 LH 6 X - - LH 8 X - - FHF 32-16/22 LH 6 X - - LH 8 X - - FHF 32-2/3 LH 6 X - - LH 8 X - - FHF 32-2/4 LH 6 X - - LH 8 X - - FHF 4-12/11 OH1 8 X 6 - - OH1 1 X 6 - - FHF 4-12/1 OH1 8 X 6 - - OH1 1 X 6 - - FHF 4-12/22 OH1 8 X 6 - - OH1 1 X 6 - - FHF 4-16/3 OH1 8 X 6 - - OH1 1 X 6 - - FHF 4-16/4 OH1 8 X 6 - - OH1 1 X 6 - - FHF 4-2/ OH1 8 X 6 - - OH1 1 X 6 - - FHF 4-2/7 OH1 8 X 6 - - OH1 1 X 6 - - FHF 4-2/11A OH1 8 X 6 - - OH1 1 X 6 - - FHF 4-2/11 OH1 8 X 6 - - OH1 1 X 6 - - FHF 4-2/1 OH1 8 X 6 - - OH1 1 X 6 - - FHF -12/22 OH2 1 X 6 - - OH2 12 X 6 - - FHF -12/3 OH2 1 X 6 - - OH2 12 X 6 - - FHF -12/4 OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 FHF -16/ OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 FHF -16/7 OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 FHF -2/11A OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 FHF -2/11 OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 FHF -2/1 OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 FHF -2/18 OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 FHF -2/22 OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 FHF 6-12/4 OH3 12 X 8 - - OH3 1 X 8 - - FHF 6-12/ OH3 12 X 8 - - OH3 1 X 8 - - FHF 6-12/7 OH3 12 X 8 - - OH3 1 X 8 - - FHF 6-16/11A OH4 1 X 8 OH3 12 X 8 OH4 2 X 8 OH3 1 X 8 FHF 6-16/11 OH4 1 X 8 OH3 12 X 8 OH4 2 X 8 OH3 1 X 8 FHF 6-16/1 OH4 1 X 8 OH3 12 X 8 OH4 2 X 8 OH3 1 X 8 FHF 6-2/1 OH4 1 X 8 OH3 12 X 8 OH4 2 X 8 OH3 1 X 8 FHF 6-2/18 OH4 1 X 8 OH3 12 X 8 OH4 2 X 8 OH3 1 X 8 FHF 6-2/22 OH4 1 X 8 OH3 12 X 8 OH4 2 X 8 OH3 1 X 8 FHF 6-2/22 OH4 1 X 8 OH3 12 X 8 OH4 2 X 8 OH3 1 X 8 FHF 6-2/3 OH4 1 X 8 OH3 12 X 8 OH4 2 X 8 OH3 1 X 8 FHF 6-2/37 OH4 1 X 8 OH3 12 X 8 OH4 2 X 8 OH3 1 X 8 FHF 8-16/1 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 FHF 8-16/18 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 FHF 8-2/22 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 FHF 8-2/3 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 FHF 8-2/37 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 FHF 8-2/4 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 FHF 8-2/ HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 * For the risk classes refer to para 6, UNI EN1284. kit-asp-fhf-en_b_td - the pumps must be chosen according to the performance levels indicated in Tab. 6 para 7.3.1, Tab.7 para 7.3.2 and the classes of risk. - some pump models can satisfy the conditions of one or more classes of risk. - always check the correct selection of the pump depending on the performance level of the set. ** Insert the mm minimal thickness under the GEN1 fire-fighting booster sets only. ACCESSORIES SORIES 141

GEN../FHF 1-12 SERIES FIRE-FIGHTING BOOSTER SETS SUCTION SIDE KIT DIMENSIONS TABLE SUCTION LIFT POSITIVE SUCTION HEAD RISK SUCTION RISK SUCTION RISK SUCTION RISK SUCTION PUMP CLASS * KIT CLASS * KIT CLASS * KIT CLASS * KIT TYPE TYPE TYPE TYPE FHF 1-16/18 HH3 2 X 12 HH2 2 X 12 HH3 2 X 12 HH2 2 X 12 FHF 1-16/22 HH4 2 X 12 HH3 2 X 12 HH4 3 X 12** HH3 2 X 12 FHF 1-16/3 HH4 2 X 12 HH3 2 X 12 HH4 3 X 12** HH3 2 X 12 FHF 1-2/18 HH3 2 X 12** HH2 2 X 12** HH3 2 X 12** HH2 2 X 12** FHF 1-2/3 HH3 2 X 12** HH2 2 X 12** HH3 2 X 12** HH2 2 X 12** FHF 1-2/37 HH4 2 X 12** HH3 2 X 12** HH4 3 X 12** HH3 2 X 12** FHF 1-2/4 HH4 2 X 12 HH3 2 X 12 HH4 3 X 12** HH3 2 X 12 FHF 1-2/3 HH3 2 X 12 HH2 2 X 12 HH3 2 X 12 HH2 2 X 12 FHF 1-2/4 HH4 2 X 12 HH3 2 X 12 HH4 3 X 12** HH3 2 X 12 FHF 1-2/ HH4 2 X 12 HH3 2 X 12 HH4 3 X 12 HH3 2 X 12 FHF 1-2/7 HH 3 X 12 HH4 2 X 12 HH 3 X 12 HH4 3 X 12 FHF 1-2/9 HH6 3 X 12 HH 3 X 12 HH6 3 X 12 HH 3 X 12 FHF 12-2/3 HH7 3 X 1 HH6 3 X 1 HH7 3 X 1 HH6 3 X 1 FHF 12-2/4 HH9 3 X 1 HH8 3 X 1 HH9 4 X 1** HH8 3 X 1** FHF 12-2/ HH1 3 X 1** HH9 3 X 1 HH1 4 X 1** HH9 4 X 1** FHF 12-27/7 HH1 3 X 1 HH9 3 X 1 HH1 4 X 1 HH9 4 X 1 FHF 12-27/9 HH1 3 X 1 HH9 3 X 1 HH1 4 X 1 HH9 4 X 1 FHF 12-27/11 HH1 3 X 1 HH9 3 X 1 HH1 4 X 1 HH9 4 X 1 FHF 12-27/132 HH1 3 X 1 HH9 3 X 1 HH1 4 X 1 HH9 4 X 1 * For the risk classes refer to para 6, UNI EN1284. kit-asp-fhf1-en_a_td - the pumps must be chosen according to the performance levels indicated in Tab. 6 para 7.3.1, Tab. 7 para 7.3.2 and the classes of risk. - some pump models can satisfy the conditions of one or more classes of risk. - always check the correct selection of the pump depending on the performance level of the set. ** Insert the mm minimal thickness under the GEN1 fire-fighting booster sets only. ACCESSORIES SORIES 142

GEN../SHF 32-8 SERIES FIRE-FIGHTING BOOSTER SETS SUCTION SIDE KIT DIMENSIONS TABLE SUCTION LIFT POSITIVE SUCTION HEAD RISK SUCTION RISK SUCTION RISK SUCTION RISK SUCTION PUMP CLASS * KIT CLASS * KIT CLASS * KIT CLASS * KIT TYPE TYPE TYPE TYPE SHF 32-12/7 LH 6 X - - LH 8 X - - SHF 32-12/11 LH 6 X - - LH 8 X - - SHF 32-16/1 LH 6 X - - LH 8 X - - SHF 32-16/22 LH 6 X - - LH 8 X - - SHF 32-2/3 LH 6 X - - LH 8 X - - SHF 32-2/4 LH 6 X - - LH 8 X - - SHF 32-2/ LH 6 X - - LH 8 X - - SHF 32-2/7 LH 6 X - - LH 8 X - - SHF 32-2/11 LH 6 X - - LH 8 X - - SHF 4-12/11 OH1 8 X 6 - - OH1 1 X 6 - - SHF 4-12/1 OH1 8 X 6 - - OH1 1 X 6 - - SHF 4-12/22 OH1 8 X 6 - - OH1 1 X 6 - - SHF 4-16/3 OH1 8 X 6 - - OH1 1 X 6 - - SHF 4-16/4 OH1 8 X 6 - - OH1 1 X 6 - - SHF 4-2/ OH1 8 X 6 - - OH1 1 X 6 - - SHF 4-2/7 OH1 8 X 6 - - OH1 1 X 6 - - SHF 4-2/11A OH1 8 X 6 - - OH1 1 X 6 - - SHF 4-2/11 OH1 8 X 6 - - OH1 1 X 6 - - SHF 4-2/1 OH1 8 X 6 - - OH1 1 X 6 - - SHF -12/22 OH2 1 X 6 - - OH2 12 X 6 - - SHF -12/3 OH2 1 X 6 - - OH2 12 X 6 - - SHF -12/4 OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 SHF -16/ OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 SHF -16/7 OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 SHF -2/11A OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 SHF -2/11 OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 SHF -2/1 OH2 1 X 6 - - OH2 12 X 6 - - SHF -2/18 OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 SHF -2/22 OH3 12 X 6 OH2 1 X 6 OH3 1 X 6 OH2 12 X 6 SHF 6-16/4 OH3 12 X 8 - - OH3 1 X 8 - - SHF 6-16/ OH3 12 X 8 - - OH3 1 X 8 - - SHF 6-16/7 OH3 12 X 8 - - OH3 1 X 8 - - SHF 6-16/11A OH3 12 X 8 - - OH3 1 X 8 - - SHF 6-16/11 OH3 12 X 8 - - OH3 1 X 8 - - SHF 6-2/1 OH3 12 X 8 - - OH3 1 X 8 - - SHF 6-2/18 OH3 12 X 8 - - OH3 1 X 8 - - SHF 6-2/22 OH4 1 X 8 OH3 12 X 8 OH4 2 X 8 OH3 1 X 8 SHF 6-2/3 OH4 1 X 8 OH3 12 X 8 OH4 2 X 8 OH3 1 X 8 SHF 6-2/37 OH4 1 X 8 OH3 12 X 8 OH4 2 X 8 OH3 1 X 8 SHF 8-16/11 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 SHF 8-16/1 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 SHF 8-16/18 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 SHF 8-2/22 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 SHF 8-2/3 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 SHF 8-2/37 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 SHF 8-2/4 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 SHF 8-2/ HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 SHF 8-2/7 HH1 2 X 1 OH4 1 X 1 HH1 2 X 1 OH4 2 X 1 * For the risk classes refer to para 6, UNI EN1284. kit-asp-shf-en_a_td - the pumps must be chosen according to the performance levels indicated in Tab. 6 para 7.3.1, Tab. 7 para 7.3.2 and the classes of risk. - some pump models can satisfy the conditions of one or more classes of risk. - always check the correct selection of the pump depending on the performance level of the set. ** Insert the mm minimal thickness under the GEN1 fire-fighting booster sets only. ACCESSORIES SORIES 143

- + ACCORDING TO EN1284 LAMPS TEST PROVA LAMPADE Plant Type: Tipo impianto: POWER ON PRESENZA TENSIONE UNDER THRESHOLD SOTTO SOGLIA PUMP ON POMPA IN MARCIA INTERRUPTED LINES! 3 LINEE INTERROTTE INCREASE SHIFT ENTER DECREASE / MENU' BUZZER SWITCH OFF TACITAZIONE SIRENA V - + L1/ A A - + L1/ A SPRINKLER DRAINAGE PUMPS ROOM FAULT PUMP L2 L1 L3 JOCKEY PUMP - + 1 2 3 POMPA COMPENSAZIONE Voltage 23 V - -6 Hz Code N. 32..1. Circ. N. 17.29.1. Battery 12 V 2,3 Ah Buzzer 12Vcc 9mA 7dB(A),2 A IP OVERLOAD SOVRACCARICO SPRINKLER PUMPS ROOM SPRINKLER SALA POMPE PUMP SET ON DEMAND RICHIESTA DI AVVIAMENTO SELECTOR NOT IN AUT. FUNCTION SELETTORE NON IN AUT. V - + L2/ B A L2/ + B L2 PHASE SEQUENCE FAILURE ERRATA SEQUENZA FASE L1 L3 MINIMUM FUEL LEVEL MIN. LIVELLO COMBUSTIBILE!! 1 2 V L3 L3 N.P. START FAILURE MANCATO AVVIAMENTO SWITCHBOARD FAILURE GUASTO QUADRO 1 ELECTRIC PUMP / POMPA ELETTRICA!! OFF OFF 1 2 DIESEL PUMP / MOTOPOMPA MINIMUM LEVEL SUCTION TANK 1 MINIMO LIVELLO VASCA ASPIRAZIONE MINIMUM LEVEL PRIMING TANK 2 MINIMO LIVELLO VASCA ADESCAMENTO! PARTIALLY OPENED SUCTION VALVE OFF VALVOLA IN ASPIRAZIONE NON 1 COMPLETAMENTE APERTA! PARTIALLY OPENED DISCHARGE VALVE OFF VALVOLA IN MANDATA NON 2 COMPLETAMENTE APERTA ALARMS CONTROL ELECTRICAL PANEL Electric panel for remote status and alarm monitoring of one or two Lowara pumps installed in GEN fire-fighting booster sets, according to EN1284. In the electric service pump mode, the following conditions are visualised: - Motor powered. - Pump start-up request. - Pump running - Failure to start. Additionally: minimum suction tank level, minimum priming tank level, on-off valve on suction and discharge side not fully open. The valves are complete with status monitor. In the diesel engine service pump mode, the following conditions are visualised, as required by EN1284: - Switch on diesel engine pump control panel in non-automatic position. - Diesel engine ails to start after 6 attempts. - Pump running - Controller fault. Additionally: minimum fuel or suction tank level, minimum priming tank level, on-off valve on suction and discharge side not fully open. The valves are complete with status monitor. All the above conditions, required by EN1284, are visualised with signal LED s and buzzers. A buzzer alarm reset button and LED tester button are included. ACCESSORIES SORIES The control unit is also fitted out to signal the following general alarms, if present: - General alarm for incorrect electrical connection in the exchange contacts of: flow meter circuit valve, discharge pump, jockey pump status. - Fault in electrical connection in the exchange contact relative to panel 1 (electric pump/diesel engine pump) - Fault in electrical connection in the exchange contact relative to panel 2 (electric pump/diesel engine pump) - Jockey pump overload (*). - Jockey pump running(*) - Discharge pump overload (*). - Battery voltage low. - Communications failure with ModBus system. All the above conditions are visualised with signal LED s and on the display. The customer may decide to enable the buzzer. The panel comprises a plastic casing (IP), battery, battery charger, alarms and pump status display, if connected with 48 serial communication. Fitted to transmit alarms for GSM or PC module. The electric connection between the contacts on the electric alarms control panel and other electric panels is to be seen to by the person installing the equipment. (*) Check that the electric control panel combined with the electric pump is complete with clean contacts for pump running and overload signals. QUADRO TAMPONE ALLARMI TECHNICAL SPECIFICATIONS DESCRIPTION VALUE Input voltage (single-phase) (1F+N) 23V +/-1%, -6 Hz Absorbed,1A Dimensions 37 x 27 x 16 mm Protection grade IP Battery Hermetic lead Rated battery voltage 12 Vcc Rated battery capacity 2,3 Ah ( uncharged in 2 h) Dimensions of battery 178 x 34 x 66 mm Sound emission levels 7dB Control panel weight 1,kg 1284-qal-en_b_td 37 Type DSRC GA11E+1D! 27 - A! 1 2! 1284_2_D_DD 144

FLOW METER KIT The flow meter is supplied as part of the assembly kit. The EN 1284 standard requires the presence of the flow meter for checking the hydraulic performance during the test stage and duration periodic inspections. The suction side kit are equipped with: - Direct reading flow meter. - On/off ball valve for diameters up to 2" inclusive, butterfly valve with lever handle from DN6 to DN1 diameter, butterfly valve with handwheel and reduction manual gear for DN12 diameter and above. Device for monitoring ON/OFF status included. Electrical connections by customer. (Valve lock kit available on request). - Connection piping. The meter is available in various sizes according to the flow of a service pump and suitable for being connected to the offtake of the head manifold. For a correct match, identify the type as shown in the set size tables. The flow meter must be installed, where possible, in a stretch of piping with a steady flow and sufficient back pressure at the discharge outlet. The assembly and the discharge piping towards the tank and discharge outlet are to be seen to by the person installing the equipment. TABELLA SHAPE DIMENSIONALE A KIT_FLUSSIMETRO SHAPE B GRUPPI SHAPE EN1284 C SHAPE D DIMENSIONS (mm) DIMENSIONS (mm) TYPE TYPE DN DNAS SHAPE L H DN DNAS SHAPE L H 32X2P 32 2 A 9 6 1X4P 1 4 B 3 76 32X32P 32 32 A 9 62 1XP 1 B 3 7 32X4P 32 4 A 9 64 1X6P 1 6 C 34 41 4X2P 4 2 A 1 6 1X8P 1 8 C 34 41 4X32P 4 32 A 1 63 1X12 1 12 D 34 94 4X4P 4 4 A 1 64 12XP 12 B 3 76 4XP 4 A 1 64 12X6P 12 6 C 34 42 X2P 2 A 1 61 12X8P 12 8 C 34 42 X32P 32 A 1 63 12X12 12 12 D 34 7 X4P 4 A 1 6 12X1 12 1 D 34 18 XP A 1 64 1X6P 1 6 C 38 43 6X2P 6 2 B 3 7 1X8P 1 8 C 38 44 6X32P 6 32 B 3 72 1X12 1 12 D 38 77 6X4P 6 4 B 3 74 1X1 1 1 D 38 9 6XP 6 B 3 73 1X2 1 2 D 38 138 6X6P 6 6 C 34 39 2X8P 2 8 C 38 46 6X8P 6 8 C 34 9 2X12 2 12 D 38 79 8X4P 8 4 B 3 74 2X1 2 1 D 38 92 8XP 8 B 3 73 2X2 2 2 D 38 117 8X6P 8 6 C 34 4 2X12 2 12 D 44 82 8X8P 8 8 C 34 4 2X1 2 1 D 44 9 8X12 8 12 D 34 91 2X2 2 2 D 44 119 1284_kit_flux-acc-en_a_td ACCESSORIES SORIES 14

TABLE OF COMBINATIONS FOR FLOW METER KIT AND FHF SERVICE PUMP SERIES TYPE COMBINATION TYPE COMBINATION FHF.. FLOW METER KIT FHF.. FLOW METER KIT ELECTRIC PUMP GEN.. ELECTRIC PUMP GEN.. PUMP D 1D 1D 11D PUMP D 1D 1D 11D 32-12/7 32-12/D119 4X2P 4X2P X2P X2P 6-2/1 6-2/D187 8X8P 8X8P 1X8P 1X8P 32-12/11 32-12/D136 4X32P 4X32P X32P X32P 6-2/18 6-2/D198 8X8P 8X8P 1X8P 1X8P 32-16/1 32-16/D1 4X32P 4X32P X32P X32P 6-2/22 6-2/D21 8X8P 8X8P 1X8P 1X8P 32-16/22 32-16/D164 4X32P 4X32P X32P X32P 6-2/22 6-2/D22 8X8P 8X8P 1X8P 1X8P 32-2/3 32-2/D188 4X32P 4X32P X32P X32P 6-2/3 6-2/D241 8X8P 8X8P 1X8P 1X8P 32-2/4 32-2/D24 4X32P 4X32P X32P X32P 6-2/37 6-2/D28 8X8P 8X8P 1X8P 1X8P 4-12/11 4-12/D112 6X4P 6X4P 6X4P 6X4P 8-16/1 8-16/D163 1X8P 1X8P 12X8P 12X8P 4-12/1 4-12/D122 6X4P 6X4P 6X4P 6X4P 8-16/18 8-16/D173 1X12 1X12 12X12 12X12 4-12/22 4-12/D143 6XP 6XP 6XP 6XP 8-2/22 8-2/D189 1X8P 1X8P 12X8P 12X8P 4-16/3 4-16/D19 6X4P 6X4P 6X4P 6X4P 8-2/3 8-2/D27 1X12 1X12 12X12 12X12 4-16/4 4-16/D171 6XP 6XP 6XP 6XP 8-2/37 8-2/D22 1X8P 1X8P 12X8P 12X8P 4-2/ 4-2/D19 6X4P 6X4P 6X4P 6X4P 8-2/4 8-2/D238 1X12 1X12 12X12 12X12 4-2/7 4-2/D29 6XP 6XP 6XP 6XP 8-2/ 8-2/D26 1X12 1X12 12X12 12X12 4-2/11A 4-2/D218 6XP 6XP 6XP 6XP 1-16/18 1-16/D1 12X12 12X12 1X12 1X12 4-2/11 4-2/D233 6XP 6XP 6XP 6XP 1-16/22 1-16/D16 12X12 12X12 1X12 1X12 4-2/1 4-2/D21 6XP 6XP 6XP 6XP 1-16/3 1-16/D18 12X1 12X1 2X1 2X1-12/22-12/D119 6XP 6XP 8XP 8XP 1-2/18 1-2/D168 12X12 12X12 1X12 1X12-12/3-12/D13 6X6P 6X6P 8X6P 8X6P 1-2/3 1-2/D192 12X12 12X12 1X12 1X12-12/4-12/D139 6X6P 6X6P 8X6P 8X6P 1-2/37 1-2/D23 12X12 12X12 1X12 1X12-16/ -16/D18 6X6P 6X6P 8X6P 8X6P 1-2/4 1-2/D213 12X12 12X12 2X12 2X12-16/7-16/D174 6X6P 6X6P 8X6P 8X6P 1-2/3 1-2/D2 12X12 12X12 1X12 1X12-2/11A -2/D197 6X6P 6X6P 8X6P 8X6P 1-2/4 1-2/D221 12X12 12X12 2X12 2X12-2/11-2/D29 6X6P 6X6P 8X6P 8X6P 1-2/ 1-2/D23 12X12 12X12 2X12 2X12-2/1-2/D224 6X6P 6X6P 8X6P 8X6P 1-2/7 1-2/D24 12X1 12X1 2X1 2X1-2/18-2/D237 6X6P 6X6P 8X6P 8X6P 1-2/9 1-2/D267 12X1 12X1 2X1 2X1-2/22-2/D2 6X6P 6X6P 8X6P 8X6P 12-2/3 12-2/D18 1X1 1X1 2X1 2X1 6-12/4 6-12/D121 8X6P 8X6P 1X6P 1X6P 12-2/4 12-2/D26 1X2 1X2 2X2 2X2 6-12/ 6-12/D129 8X6P 8X6P 1X6P 1X6P 12-2/ 12-2/D216 1X2 1X2 2X2 2X2 6-12/7 6-12/D14 8X6P 8X6P 1X6P 1X6P 12-27/7 12-27/D224 1X2 1X2 2X2 2X2 6-16/11A 6-16/D161 8X8P 8X8P 1X8P 1X8P 12-27/9 12-27/D237 1X2 1X2 2X2 2X2 6-16/11 6-16/D168 8X8P 8X8P 1X8P 1X8P 12-27/11 12-27/D23 1X2 1X2 2X2 2X2 6-16/1 6-16/D178 8X8P 8X8P 1X8P 1X8P 12-27/132 12-27/D266 1X2 1X2 2X2 2X2 ACCESSORIES SORIES 1284_kit_flux-fhf_D-11D-en_b_th 146

TABLE OF COMBINATIONS FOR FLOW METER KIT AND SHF SERVICE PUMP SERIES TYPE COMBINATION TYPE COMBINATION SHF.. FLOW METER KIT SHF.. FLOW METER KIT ELECTRIC PUMP GEN.. ELECTRIC PUMP GEN.. PUMP D 1D 1D 11D PUMP D 1D 1D 11D 32-12/7 32-12/D121 4X32P 4X32P X32P X32P -2/11A -2/D197 6X6P 6X6P 8X6P 8X6P 32-12/11 32-12/D136 4X32P 4X32P X32P X32P -2/11-2/D29 6X6P 6X6P 8X6P 8X6P 32-16/1 32-16/D1 4X32P 4X32P X32P X32P -2/1-2/D224 6X6P 6X6P 8X6P 8X6P 32-16/22 32-16/D168 4X32P 4X32P X32P X32P -2/18-2/D237 6X6P 6X6P 8X6P 8X6P 32-2/3 32-2/D188 4X32P 4X32P X32P X32P -2/22-2/D2 6X6P 6X6P 8X6P 8X6P 32-2/4 32-2/D24 4X32P 4X32P X32P X32P 6-16/4 6-16/D119 8X6P 8X6P 1X6P 1X6P 32-2/ 32-2/D222 4X32P 4X32P X32P X32P 6-16/ 6-16/D129 8X6P 8X6P 1X6P 1X6P 32-2/7 32-2/D242 4X32P 4X32P X32P X32P 6-16/7 6-16/D137 8X6P 8X6P 1X6P 1X6P 32-2/11 32-2/D26 4X32P 4X32P X32P X32P 6-16/11A 6-16/D168 8X6P 8X6P 1X6P 1X6P 4-12/11 4-12/D112 6X4P 6X4P 6X4P 6X4P 6-16/11 6-16/D177 8X6P 8X6P 1X6P 1X6P 4-12/1 4-12/D126 6X4P 6X4P 6X4P 6X4P 6-2/1 6-2/D192 8X6P 8X6P 1X6P 1X6P 4-12/22 4-12/D143 6X4P 6X4P 6X4P 6X4P 6-2/18 6-2/D23 8X6P 8X6P 1X6P 1X6P 4-16/3 4-16/D19 6X4P 6X4P 6X4P 6X4P 6-2/22 6-2/D21 8X8P 8X8P 1X8P 1X8P 4-16/4 4-16/D171 6XP 6XP 6XP 6XP 6-2/3 6-2/D24 8X8P 8X8P 1X8P 1X8P 4-2/ 4-2/D19 6XP 6XP 6XP 6XP 6-2/37 6-2/D2 8X8P 8X8P 1X8P 1X8P 4-2/7 4-2/D29 6XP 6XP 6XP 6XP 8-16/11 8-16/D169 1X8P 1X8P 12X8P 12X8P 4-2/11A 4-2/D218 6X4P 6X4P 6X4P 6X4P 8-16/1 8-16/D177 1X8P 1X8P 12X8P 12X8P 4-2/11 4-2/D233 6X4P 6X4P 6X4P 6X4P 8-16/18 8-16/D186 1X12 1X12 12X12 12X12 4-2/1 4-2/D21 6XP 6XP 6XP 6XP 8-2/22 8-2/D198 1X12 1X12 12X12 12X12-12/22-12/D119 6XP 6XP 8XP 8XP 8-2/3 8-2/D21 1X12 1X12 12X12 12X12-12/3-12/D13 6X6P 6X6P 8X6P 8X6P 8-2/37 8-2/D226 1X12 1X12 12X12 12X12-12/4-12/D139 6X6P 6X6P 8X6P 8X6P 8-2/4 8-2/D237 1X12 1X12 12X12 12X12-16/ -16/D18 6X6P 6X6P 8X6P 8X6P 8-2/ 8-2/D22 1X12 1X12 12X12 12X12-16/7-16/D174 6X6P 6X6P 8X6P 8X6P 8-2/7 8-2/D27 1X12 1X12 12X12 12X12 1284_kit_flux-shf_D-11D-en_c_th ACCESSORIES SORIES 147

PRIMING TANK The priming tank is used in suction lift installations and carries out the function of maintaining the pump body and suction pipe full of water even if there are leaks through the bottom valve. Each pump must have its own independent priming tank, placed at a higher level than the pump. The tank must be connected to a water source for adding water and keeping it full. The diameter of the connecting pipe to the pump depends on the use class. The return piping for re-circulation can be connected to the tank, which must also provide for discharge if it is too full. A level indicator automatically actions the service pump if the level of the tank drops and is not reintegrated. The hydraulic connections must be seen to by the person installing the equipment. The horizontal l tank is made of zinc-plated steel. ACCESSORIES SORIES PRIMING TANK KIT The available accessories kit includes: - Filling and discharge valves, reductions, non-return valve, closing plugs and automatic air discharger. - Float switch tap complete with ring nut for fixing to the hole through the tank. - Level indicator to connect to the electric panel and assembly instruction sheet. Available on request tank support, height 7, 1, 1, 2 cm. Example of connection to the tank and accessories: ACCESSORIES SORIES N DESCRIPTION N DESCRIPTION 1 Pump priming tank 8 Priming supply non return valve 2 Pipe return from pump delivery side 9 Priming supply on-off valve 3 Floating valve 1 Over flow 4 In flow on-off valve 11 Pressure switch In flow 12 Pump 6 Low level switch 13 To trunk main 7 Drain 14 Pipe connection to delivery side of the pump En-acc-adesc-en_b_tc 148

ELECTRIC JOCKEY PUMP KIT The jockey pump or compensation pump has the job of keeping the system under pressure and compensating for any small loses without the intervention of the service pumps. In fact, the jockey pump is commanded by an automatic shut-off panel. Should an electric jockey pump of a different size from the standard be required or should it be installed later on sets which are not predisposed, or should non-standard different size requirements be required, it is possible to configure the booster set with just the service pumps and add the electric jockey pump, also later on. The kit includes: - the hydraulic components for installing the electric pump (base, valves, pressure switch). - the pre-chosen electric pump and the relative electric panel. The hydraulic connection to the set can be easily carried out using one of the couplings on the delivery manifold for the membrane tanks using an adaptor. Kits are available for the vertical electric jockey pumps 1SV series and submersed series 2GS, 4GS, 6GS. The diagram illustrates some connection examples: ACCESSORIES SORIES N DESCRIPTION 1 Electric pump 2 Control Box 3 Connection to trunk main 4 Pipe connection to delivery side of the jockey pump To trunk main acc-kit-fil-en_a_tc 149

PANEL BRACKET KIT The electric command panels supplied separately, for example in the sets with submersed pumps, are suitable for being mounted on the wall. Universal bracket kit are available, upon request, for supporting the panels; it must be fixed to the floor using blocks. GU_ACC_M1_A_SC HYDRAULIC CONNECTION FOR FIRE-FIGHTING EN 1284 SETS ACCESSORIES SORIES N DESCRIPTION N DESCRIPTION 1 Suction piping kit * Flow meter kit * 2 Delivery manifold 6 Drain 3 Drain 7 Open discharge 4 From priming tank * 8 To trunk main * See the instruction sheets. En-acc-gener-en_a_tc 1

ACCESSORIES SORIES NEW RATE OF FLOW INDICATOR < DN1 FLOATS MONITORED VALVES VALVES HYDRO TUBE ACCESSORIES SORIES FLOW METER RATE OF FLOW INDICATOR ELASTIC JOINTS PRESSURE SWITCHS 11

PRODUCT DESCRIPTION BY TECHNICAL SPECIFICATIONS Description EN 1284 fire-fighting booster set Series : GEN Model: electric service pump diesel service pump jockey or compensation pump The pump station will comprise the following components: - N 1 electric jockey pump; - N 1 electric service pump;- N 1 backup diesel pump; - One electrical power and control panel for the electric service pump; - One electrical power and control panel for the diesel pump; - One electrical power and control panel for the electric jockey pump; - Components and materials required for perfect operation and assembly; Lowara booster sets are CE-certified and comply with the following directives: - Machinery Directive 26/42/EC. - Low Voltage Directive 26/9/EC. - Electromagnetic Compatibility Directive 24/18/EC. The hydraulic pump complies with the following standard: - ISO 996-A Rotodynamic pumps hydraulic performance acceptance tests. The fire-fighting booster set complies with European standard EN 1284: Fixed fire-fighting installations Automatic sprinkler systems, design, installation and maintenance. Version with automatic switch-off according to UNI 1779 Hydrant systems design, installation and operating. ACCESSORIES SORIES 12

PRODUCT DESCRIPTION BY TECHNICAL SPECIFICATIONS Basic version with periodic auto-test, Series GEN..A. Electronic auto-test circuit with weekly programmer in the electrical panel of the service pump. The pump is turned on an kept working for a minute at the previously established time and date. During this interval the check circuit checks that the pressure in the re-circulation circuit closes the pressure switch contact of the pump which is running. In the case of irregularities, the relative auxiliary self-test alarm relay available for remote signalling is activated and memorised. The EN 1284 Standard does not provide for the presence of a self-test circuit but asks for periodic checks to be carried out by the user, hence the periodic self-test function cannot substitute the above checks. For the precalculated HHP and HHS risk class systems and in the integrally calculated systems, the pump must be able to provide, at 14% of rated capacity, a pressure of not less than 7% of the rated pressure of the pump. Each pump generally backs up the other even if much depends on the chosen type of water supply. If the service pump fails, or a blackout occurs, system pressure will decrease and the backup diesel pump will start. The pumps are started automatically by the pressure switches while they are manually stopped from the electrical panel (key switch). Fire-fighting set components: electric pump Electric service pump comprising: End-suction horizontal centrifugal pump, model FHF..., single impeller, with cast iron body and AISI316L stainless steel shaft. End suction and radial discharge ports. Impeller in AISI316L stainless steel or cast iron. Hydraulic sizes and nominal diameter DN of suction and discharge ports according to EN 733 (ex DIN 242). Flanging to EN 192-2 (formerly UNI2236) and DIN232. Maximum running pressure: 12 bar. Mechanical seal according to EN1276 (formerly DIN 2496) in Ceramic/Carbon/NBR lubricated with recirculation duct between discharge and seal housing. The pump is directly coupled to the respective motor with an elastic spacer joint ( back pull out version) and alignment and anchor base. B3 three-phase electric motor with short circuit squirrel cage, totally enclosed, fan-cooled. The performance levels of the electric motors lie within what is usually referred to as efficiency class 1. Protected to IP, insulation class F. ACCESSORIES SORIES 13

PRODUCT DESCRIPTION BY TECHNICAL SPECIFICATIONS Main characteristics of the electric service pump: TABELLA MATERIALI POMPA SERVIZIO FHF PER CAPITOLATI TECNICI Brand Model: Flow rate Head: Pump body: Seal housing: Impeller: Shaft: Elastomers: Mechanical seal: Motor power: LOWARA FHF Cast iron, EN 161-GJL-2 (JL13) Cast iron, EN 161-GJL-2 (JL13) Cast iron, EN 161-GJL-2 (JL13) Stainless steel EN188-1-X2 CrNiMo17-12-2 NBR Ceramic/Carbon/NBR m3/h m.c.a. Kw Input voltage: 4 / 3 V Frequency: Hz Rated current input: A Speed of rotation: 29 r.p.m. Max. ambient temp: 4 ºC Protection class: Insulation class: IP F tec_fhf-en_b_tm Backup up diesel engine pump comprising: Normalised horizontal centrifugal pump, FHF... according to EN 733 (ex DIN 242) max. operating pressure PN12. End suction and radial discharge ports. Impeller in AISI316L stainless steel or cast iron, mechanical seal in Ceramic/Carbon/NBR lubricated with recirculation duct between the discharge and the seal housing according to EN1276 (formerly DIN 2496). Main components of the diesel engine pump: - Electrical panel with battery charger. - Diesel engine start circuit with two independent batteries. ACCESSORIES SORIES - Double engine starting relay. - Engine shut-off device from electric control (Electric stop). - Fuel tank for diesel engine equipped with float - Diesel engine coupled to service pump. - Base made of structural steel with epoxy powder painting RAL 1. The diesel pump is supplied on its own base complete with vibration-proof feet, wall-mounted electrical panel fixed to the bracket of the set complete with 3-metre long cable ( metres available on request) wall- or floor-mounted fuel tank depending on capacity, pair of batteries lying on base with three metres of electrical cable for positioning by the final user near the diesel engine. 14

PRODUCT DESCRIPTION BY TECHNICAL SPECIFICATIONS Main characteristics of the diesel engine service pump: TABELLA MATERIALI MOTOPOMPA SERVIZIO FHF PER CAPITOLATI TECNICI Brand: LOWARA Model: DFHF Flow rate: m3/h Head: m.c.a. Pump body: Cast iron, EN 161-GJL-2 (JL13) Seal housing: Cast iron, EN 161-GJL-2 (JL13) Impeller: Cast iron, EN 161-GJL-2 (JL13) Shaft: Stainless stee EN188-1-X2 CrNiMo17-12-2 Elastomers: NBR Mechanical seal: Ceramic/Carbon/NBR Diesel engine motor power: Kw Motor speed: 3 r.p.m. Max. ambient temp.: 4 ºC Diesel fuel tank capacity: l tec_dfhfe-en_b_tm Electric jockey ey pump comprising: Multi-cell vertical centrifugal Jockey pump, 1SV... with metal parts in contact with liquid in stainless steel, pump body and shaft in AISI 34 stainless steel, impeller in AISI 34 stainless steel, mechanical seal in Carburundum/ carbon/epdm. Three-phase electric motor, shape B14, performance values within what is referred to as efficiency class 2, short circuit squirrel cage motor, closed aluminium casing and external ventilation, performance according to EN 634-1, directly coupled to the vertical pump. Protected to IP, insulation class F. ACCESSORIES SORIES 1

PRODUCT DESCRIPTION BY TECHNICAL SPECIFICATIONS Main technical characteristics of the jockey pump: TABELLA MATERIALI POMPA SERVIZIO SV PER CAPITOLATI TECNICI Brand: Model: Flow rate: Head: Pump body: Impeller: Diffuser: Shaft: Outer sleeve: Mechanical seal: Motor power: Stainless steel (1.431) Stainless steel (1.431) Stainless steel (1.431) Stainless steel (1.431) Stainless steel (1.431) Silicon carbide/carbon/epdm LOWARA 1SV m3/h m.c.a. Kw Input voltage: 4 / 3 V Frequency: Hz Rated current: A Speed: 29 r.p.m. Max. ambient temp.: 4 ºC Protection class: Insulation class: IP - F tec_sv-en_b_tm Electric panels Electric service pump panel Painted metal casing (IP4) complete with: ACCESSORIES SORIES - General door-locking switch. - Analogical ammeter. - MAN AUT selector with extractable key only in automatic position. - Keyboard for indicating electric voltage presence, correct phase sequence (three phase power supply), start-up request, pump functioning and no start-up, through LED lamps, lamp test button and starting and stopping buttons, according to the provisions of EN1284 paragraph 1.8.6. Inside: - 12/24V transformer for auxiliary circuits and electronic board. - Fuse holder and fuses for power and auxiliary circuits. 16

PRODUCT DESCRIPTION BY TECHNICAL SPECIFICATIONS - Line contact maker (direct start-up), line and star/delta contact makers (star/delta start-up), line contact makers and reactance switching (impedance start-up). - Star/delta exchanger timer or reactance switching. - Relay for signalling no phase. - Auxiliary relays. - Current transformer. - Terminal boards. - Clean contacts (max 24V, 1A) for activating acoustic/ visual alarms for no phase, pump on demand, pump running and start failure. - Cable glands (excluding the versions to be fixed to the floor). - Wiring diagram. Jockey pump electrical panel Painted metal casing (IP) complete with: - General door-locking switch. - Visual indicators for line, running, thermal shutdown. - Manual automatic selector excluded. Inside: - Transformer for auxiliary circuits at 24 V. - Fuse holder and fuses for power and auxiliary circuits. - Line contact maker. - Overload cut-out switch. - Pump shut-off timer ( 9 s). - Terminal boards. - Cable glands. - Wiring diagram. Suitable for connecting to a float switch or a minimum pressure switch for preventing dry running. An optional level control module (supplied upon request) allows the connection of probes with the possibility of regulating the sensitivity according to the hardness of the water. Control panel for diesel engine pump Painted metal casing (IP4) complete with: - General door-locking switch. Electronic unit for control and management of the diesel engine. Display of alarms and status, battery voltage, speedometer, hour counter, alarm programming, date display, main signals and manual start button. ACCESSORIES SORIES 17

PRODUCT DESCRIPTION BY TECHNICAL SPECIFICATIONS - MAN AUT selector with extractable key only in automatic position. - Pair of emergency battery start buttons. Inside: - Fuse holder and fuses for power and auxiliary circuits. - Pair of battery chargers 12Vdc/24Vdc. - Control unit for management of diesel engine and alarms. - Auxiliary relays. - Power circuits for engine heaters. - Terminal boards. - RS232 connector for communication port. - Cable glands. - Wiring diagram. The panel is supplied standard with dry alarm signal contacts (max 1ª, 3Vdc/12vac/277Vac): ac): - Non-automatic operating mode. - Controller fault. - Motor running. - Failure to start. - General alarm. Standard single-phase input voltage 1 x 23V. Series of clean contacts for checking the status of the electric service pump panel, as well as the contacts already provided for signalling alarms (on request): ACCESSORIES SORIES - No phase. - Motor running.. - Selector position Man-Aut-. - Failure to start. - Start-up request. Series of clean contacts for checking the status of the electric jockey pump (on request) - Pump running. - Thermal shutdown (overload). - No water. Electrical alarms panel Plastic casing protected to IP with an electronic board at the front for the visual and acoustic signalling of the status of one or two service pumps. The following alarms are signalled : 18

- + ACCORDING TO EN1284 LAMPS TEST PROVA LAMPADE Plant Type: Tipo impianto: POWER ON PRESENZA TENSIONE UNDER THRESHOLD SOTTO SOGLIA PUMP ON POMPA IN MARCIA INTERRUPTED LINES! 3 LINEE INTERROTTE INCREASE SHIFT ENTER DECREASE / MENU' BUZZER SWITCH OFF TACITAZIONE SIRENA V - + L1/ A A - + L1/ A SPRINKLER DRAINAGE PUMPS ROOM FAULT PUMP L2 L1 L3 JOCKEY PUMP - + 1 2 3 POMPA COMPENSAZIONE Voltage 23 V - -6 Hz Code N. 32..1. Circ. N. 17.29.1. Battery 12 V 2,3 Ah Buzzer 12Vcc 9mA 7dB(A),2 A IP OVERLOAD SOVRACCARICO SPRINKLER PUMPS ROOM SPRINKLER SALA POMPE PUMP SET ON DEMAND RICHIESTA DI AVVIAMENTO SELECTOR NOT IN AUT. FUNCTION SELETTORE NON IN AUT. V - + L2/ B A L2/ + B L2 PHASE SEQUENCE FAILURE ERRATA SEQUENZA FASE L1 L3 MINIMUM FUEL LEVEL MIN. LIVELLO COMBUSTIBILE!! 1 2 V L3 L3 N.P. START FAILURE MANCATO AVVIAMENTO SWITCHBOARD FAILURE GUASTO QUADRO 1 ELECTRIC PUMP / POMPA ELETTRICA!! OFF OFF 1 2 DIESEL PUMP / MOTOPOMPA MINIMUM LEVEL SUCTION TANK 1 MINIMO LIVELLO VASCA ASPIRAZIONE MINIMUM LEVEL PRIMING TANK 2 MINIMO LIVELLO VASCA ADESCAMENTO! PARTIALLY OPENED SUCTION VALVE OFF VALVOLA IN ASPIRAZIONE NON 1 COMPLETAMENTE APERTA! PARTIALLY OPENED DISCHARGE VALVE OFF VALVOLA IN MANDATA NON 2 COMPLETAMENTE APERTA PRODUCT DESCRIPTION BY TECHNICAL SPECIFICATIONS Electric pump Power off. Start-up request. Pump running. No start-up. Diesel pump Non-automatic. Controller fault. Pump running. No start-up. The electric panel is fitted with a buzzer with reset button, signal LED test button, battery charger and battery and is fitted out to signal the following general alarms, if present: - General alarm for incorrect electrical connection in the exchange contacts of: status of flow measurement circuit valve, drain pump, jockey pump. - Fault in electrical connection in the exchange contact relative to panel 1 (electric pump/diesel engine pump). - Fault in electrical connection in the exchange contact relative to panel 2 (electric pump/diesel engine pump). - Jockey pump overload. - Jockey pump running. - Discharge pump overload. - Battery voltage low. - Communications failure with ModBus system. GSM modem system status transmission module and RS232/48 converter module available on request. QUADRO TAMPONE ALLARMI TECHNICAL SPECIFICATIONS 27 DESCRIPTION VALUE Input voltage (single-phase) (1F+N) 23V +/-1%, -6 Hz Absorbed,1A Dimensions 37 x 27 x 16 mm Protection grade IP Battery Hermetic lead Rated battery voltage 12 Vcc Rated battery capacity 2,3 Ah ( uncharged in 2 h) Dimensions of battery 178 x 34 x 66 mm Sound emission levels 7dB Control panel weight 1,kg Control instruments and hydraulic accessories The main components of the sets are: 1284-qal-en_b_td - On/off valves on the delivery side of each pump, ball valves with lever handle for diameters up to 11/4" inclusive, butterfly valve with lever handle from DN6 to DN1 diameter, butterfly valve with handwheel and reduction manual gear for DN12 diameter and above. - Re-circulation device for each service pump. The re-circulation device allows a minimum capacity in order to prevent the pump overheating when working with closed delivery. It includes the activation pressure switch for the alarms of the pumps running, the test valve for checking the seal of the check valves, the couplings for any connecting pipes to the priming tank in the case of suction lift installation. The connection of each re-circulation to the suction tank or the priming tank is to be seen to by the person installing the equipment. 37 Type DSRC GA11E+1D! - A! 1 2! 1284_2_D_DD ACCESSORIES SORIES 19

PRODUCT DESCRIPTION BY TECHNICAL SPECIFICATIONS - Pressure gauge on the delivery side of each service pump between check valve and on/off valve. - Check valve be inspected type, on the delivery side of each pump. Threaded connector up to and including a diameter of 11/4". Flanged connector for larger diameters. - Painted iron delivery manifold (PN 16) and threaded stubs with relative caps for connecting any 24 litre membrane tanks. Blind and welding zinc-plated flanges. - Two start-up pressure switches for every service pump. For the electric service pumps, start-up takes place through the pressure switch, but it must be manually stopped using the key-operated selector switch on the panel (excluding the version with automatic shut-off). For the electric jockey pump, if present, both start-up and stopping are determined by the pressure switch. - Start-up pressure switch circuit for the service pump, including connecting pipes for the delivery manifold, recirculation circuit. This circuit includes on/off valve, a non-return valve, a discharge or test valve and various pipe fittings. The configuration of the circuit allows the pressure switch to intervene also when the relative on/off valve is closed. - Various pipe fittings (copper, zinc-plated steel). - Base made of bent sheet or structural iron with epoxy powder painting RAL 1. - Control panel frame made of structural iron with epoxy powder painting RAL 1. The control panels for the electric pumps up to kw power supply are fixed on bracket. For higher powers, the control panels for electric pump service are floor mounted, instead the jockey electric pump panel is wall mounted fixed. - Diesel engine with coupling to service pump. - Vibration-damping joints on discharge side. - Electric panel for control of diesel engine pump and battery charger. ACCESSORIES SORIES - Diesel engine start circuit with two independent batteries. - Double engine starting relay. - Engine shut-off device from electric control (electric stop). - Fuel tank for diesel engine. 16

PRODUCT DESCRIPTION BY TECHNICAL SPECIFICATIONS - Electric panel for each electric service pump. The diesel engine pump is mounted on its own base complete with vibration-damping feet, and comes with a wall-mounted electric panel fitted with 3-metre cables ( metre length available on request), fuel tank with wall or floor mounting depending on capacity, floor-mounted batteries with iron frame to position to the side of the diesel engine. The installation of the diesel engine must provide for adequate ventilation and exhaust of combustion fumes. Flow meter The flow meter is supplied as part of the assembly kit. The EN 1284 standard requires the presence of the flow meter for checking the hydraulic performance during the test stage and duration periodic inspections. The kit comprises: - Direct reading flow meter. - On/off ball valve for diameters up to 2 inclusive, butterfly valve with lever handle from DN6 to DN1 diameter, butterfly valve with handwheel and reduction manual gear for DN12 diameter and above. - Straight plastic connection piping. IThe flow meter is available in various sizes according to the flow of a service pump and suitable for being connected to the offtake of the head manifold. For a correct match, identify the type as shown in the set size tables. The assembly and the discharge piping towards the tank and discharge outlet are to be seen to by the person installing the equipment. The following illustration shows the type and size of flow meter: Dimensions (mm): DN = DNAS = L = H = Qmax (m 3 /h) = ACCESSORIES SORIES 161

PRODUCT DESCRIPTION BY TECHNICAL SPECIFICATIONS Diaphragm tanks The booster sets are ready for installation, directly on the manifold, of 24-litre diaphragm tanks, one for each pump. The sets are also equipped with caps to close off the unused couplings. Larger tanks can also be connected to the unused end of the discharge manifold. The kit is made up of the following accessories: - Diaphragm tank; - On-off ball valve; - Instructions manual; - Packaging. Suction kit The EN 1284 fire-fighting booster sets are supplied without valves and stubs on the suction side of the service pump and can be completed with suitable kits that depend on legal standards. These requirements are expressed by EN 1284 (chapter 1. and chapter 1.6) and are connected with the maximum speed value of the water in the pipes, their minimum section and type of installation - suction lift or positive suction head. To provide for one suction kit for each duty pump. The kit comprises: - Anti-vibration joint to attach to the pump inlet. - On/off butterfly valve (optional in case of positive suction head installation) with lever handle for diameters up to DN1, butterfly valve with handwheel and reduction manual gear for DN12 and higher. - Eccentric cone. - Vacuum pressure gauge. - Weld-on flange. The following illustration shows the suction kit: ACCESSORIES SORIES Dimensions (mm): DNA = L = DNS = H= 162

PRODUCT DESCRIPTION BY TECHNICAL SPECIFICATIONS The set is supplied already assembled, calibrated and factory tested. The set is supplied complete with an instruction manual, pump manuals and wiring diagrams for the panels. For the sets including floor panels, the electric panels are sent together with the set in a separate pack and supplied with -metre long connecting cables (longer lengths available on request). The fitter is responsible for preparing the routes and installing the cables. ACCESSORIES SORIES 163

FURTHER PRODUCT SELECTION AND DOCUMENTATION TION Xylect Xylect is pump solution selection software with an extensive online database of product information across the entire Lowara, and Vogel range of pumps and related products, with multiple search options and helpful project management facilities. The system holds up-to-date product information on thousands of products and accessories. The possibility to search by applications and the detailed information output given makes it easy to make the optimal selection without having detailed knowledge about the Lowara and Vogel products. The search can be made by: Application Product type Duty point ACCESSORIES SORIES Xylect gives a detailed output: List with search results Performance curves (flow, head, power, efficiency, NPSH) Motor data Dimensional drawings Options Data sheet printouts Document downloads incl dxf files The search by application guides users not familiar with the product range to the right choice. 164

FURTHER PRODUCT SELECTION AND DOCUMENTATION TION Xylect The detailed output makes it easy to select the optimal pump from the given alternatives. The best way to work with Xylect is to create a personal account. This makes it possible to: Set own standard units Create and save projects Share projects with other Xylect users Every user have a My Xylect space, where all projects are saved. ACCESSORIES SORIES For more information about Xylect please contact our sales network or visit www.xylect.com. Dimensional drawings appear on the screen and can be downloaded in dxf format. 16

ACCESSORIES SORIES 166

Xylem 1) The tissue in plants that brings water upward from the roots; 2) a leading global water technology company. We re 12, people unified in a common purpose: creating innovative solutions to meet our world s water needs. Developing new technologies that will improve the way water is used, conserved, and re-used in the future is central to our work. We move, treat, analyze, and return water to the environment, and we help people use water efficiently, in their homes, buildings, factories and farms. In more than 1 countries, we have strong, long-standing relationships with customers who know us for our powerful combination of leading product brands and applications expertise, backed by a legacy of innovation. For more information on how Xylem can help you, go to xyleminc.com. Headquarters LOWARA S.r.l. Unipersonale Via Lombardi 14 367 Montecchio Maggiore - Vicenza - Italy Tel.(+39) 444 77111 - Fax(+39) 444 492166 e-mail: lowara.mkt@xyleminc.com web: www.lowara.com - www.completewatersystems.com LOWARA reserves the right to make modification without prior notice. LOWARA is a trademark of Xylem Inc. or one of its subsidiaries.