TECHNICAL BROCHURE B5-33GB 5GB, 7GB, 10GB, 18GB, 25GB, 33GB HIGH PRESSURE MULTI-STAGE BOOSTER PUMP

Transcription

1 TECHNICAL BROCHURE B-33GB GB, 7GB, 1GB, 18GB, 2GB, 33GB HIGH PRESSURE MULTI-STAGE BOOSTER PUMP

2 FEATURES Multi-stage Design: Provides steady, quiet, vibration free, operation. Optional Stainless Steel Construction: Standard cast iron for general service or stainless for filtration applications. O-Ring Casing Seal: Reliable high pressure sealing with easy disassembly for maintenance or repair. Impellers and Diffusers: Glass filled engineered composite material with a fixed impeller design. High resistance to corrosion and abrasion. Bowls: 3 stainless steel rabbit lock for positive alignment with no gaskets required. Variable Capacity: Centrifugal pump design permits selection of flow within a range for each size. Mechanical Seal: A variety of face materials and elastomers to match application needs. Motors: Close coupled NEMA 6J motors in open drip proof or totally enclosed design. Single phase and three phase available. Ball bearings carry all radial and axial thrust loads. Designed for continuous operation. LPP GB-2GB are tested to CSA-C22.2 No GBS-33GBS are CSA No APPLICATIONS Residential, commercial or agricultural pressure wash Reverse osmosis Evaporative cooling systems/misters Booster service Spray systems Water circulation Filtration HVAC General purpose pumping WARNINGS Pumps used on open spray applications must be plugged into electrical service which is protected by a Ground Fault Service Interruptor. Failure to do so may result in serious personal injury or death and property damage. Do not run pump dry. Do not run pump below minimum flow. If positive suction pressure is not available, be sure pump and suction line (with foot valve) are primed before starting pump. SPECIFICATIONS Pump Maximum suction (inlet) pressure: 7. Maximum Liquid Temperature: 16º F (71º C). Rotation: Clockwise when viewed from motor end. Maximum lift with foot valve: 1 ft., check NPSH curve. Motor: NEMA standard 6J frame. Open drip proof or totally enclosed fan cooled enclosures available as standard. Consult factory for other options. 6 Hz, 3 RPM. Single phase (11/23 V), three phase (3 HP, 23 V) or three phase (28-23/46 V). Single phase motors have built-in capacitor and overload with automatic reset. Note: For three phase motors, Class 2 overload protection must be provided in starter unit. Starter with overloads must be ordered separately. MATERIALS OF CONSTRUCTION Item Description Material 1 Motor Adapter Cast Iron or Cast 34 Stainless Steel =Carbon/Ceramic/BUNA 2 Mechanical Seal 3=Carbon/Silcar/EPR 4=Carbon/Silcar/Viton 3 Shaft Coupling Stainless Steel 4 Impeller/Diffuser Engineered Composite Bowl 34 Stainless Steel 6 Discharge Head 34 Stainless Steel Cast Iron or Cast 34 Stainless Steel 7 Hex Shaft Stainless Steel 8 Casing 34 Stainless Steel PAGE

3 PERFORMANCE COVERAGE 6 HZ, 3 RPM GPM RPM: 3 CURVE NO. CN434R GB 7GB 1GB 18GB 33GB 2GB FLOW RATE PERFORMANCE COVERAGE HZ, 29 RPM GPM RPM: 29 CURVE NO. CN62R GB 1GB 18GB 1 1 7GB 1 2GB 33GB FLOW RATE PAGE 3

4 GB NUMBERING SYSTEM The various versions of the Series GB are identified by a product code number on the pump label. This number is also the catalog number for the pump. The meaning of each digit in the product code number is shown below. The following are the standard 6 Hz product numbers and are built with Single Phase ODP motors and standard staging. The cast iron version uses Seal Code and the stainless version uses Seal Code 4. Order No. Description Cast Iron Stainless HP Phase Voltage Enclosure Stages GBC3 GBS GBC GBS ½ 9 GBC7 GBS7 ¾ 14 GBC1 GBS GBC 7GBS ½ 9 7GBC7 7GBS7 ¾ ODP 13 7GBC1 7GBS GBC7 1GBS7 ¾ 8 1GBC1 1GBS GBC1 1GBS1 1½ 1 1GBC2 1GBS Unit is supplied with ½ HP motor. * All 3 HP motors are 23V only. Order No. Description Cast Iron Stainless HP Phase Voltage Enclosure Stages 18GBC7 18GBS7 ¾ 18GBC1 18GBS GBC1 18GBS1 1½ 9 18GBC2 18GBS GBC3 18GBS GBC7 2GBS7 ¾ 2GBC1 2GBS GBC1 2GBS1 1½ * ODP 9 2GBC2 2GBS GBC3 2GBS GBC1 33GBS1 1 33GBC1 33GBS1 1½ 7 33GBC2 33GBS GBC3 33GBS GB SPECIFICATIONS Maximum Flow: 8 GPM Minimum Flow: 1 GPM Heads: to 6 ft. (26 ) Pipe Connections: 1" NPT Suction and Discharge 18GB SPECIFICATIONS Maximum Flow: 28 GPM Minimum Flow: 6 GPM Heads: to 47 ft. (23 ) Pipe Connections: 1" NPT Suction and Discharge 7GB SPECIFICATIONS Maximum Flow: 1 GPM Minimum Flow: 1 GPM Heads: to ft. (216 ) Pipe Connections: 1" NPT Suction and Discharge 2GB SPECIFICATIONS Maximum Flow: 33 GPM Minimum Flow: 8 GPM Heads: to 43 ft. (186 ) Pipe Connections: 1" NPT Suction and Discharge 1GB SPECIFICATIONS Maximum Flow: 16 GPM Minimum Flow: 3 GPM Heads: to 6 ft. (242 ) Pipe Connections: 1" NPT Suction and Discharge 33GB SPECIFICATIONS Maximum Flow: 33 GPM Minimum Flow: 1 GPM Heads: to 7 ft. (249 ) Pipe Connections: 1" NPT Suction and Discharge PAGE 4

5 GB NUMBERING SYSTEM For optional motor enclosures, seals and three phase configurations use the following product code system. Example Code GB C 1 J MECHANICAL SEAL AND O-RING = Standard on Cast Iron and 4 = Standard on Stainless Steel. For Optional Mechanical Seal modify catalog order no. with Seal Code listed below. Mechanical Seal ( 8 seal) Seal Rotary Stationary Elastomers Metal Part No. Casing Code Parts O-Ring Ceramic BUNA 18-8SS 1K1 BUNA 3 Carbon EPR 1K18 EPR Sil-Carbide 316SS 4 Viton 1K Viton NUMBER OF STAGES A = 1 D = 4 G = 7 K = 1 N = 13 R = 16 U = 19 X = 22 B = 2 E = H = 8 L = 11 P = 14 S = 17 V = 2 Y = 23 C = 3 F = 6 J = 9 M = 12 Q = 1 T = 18 W = 21 Z = 24 DRIVER 1 = 1 PH, ODP 4 = 1 PH, TEFC 2 = 3 PH, ODP = 3 PH, TEFC 3 = 3 PH, 7V ODP 6 = 3 PH, 7V, TEFC DRIVER: HERTZ/POLE/RPM 1 = 6 Hz, 2 pole, 3 RPM 2 = Hz, 2 pole, 29 RPM HP RATING 3 = 1 3 HP* 1 = 1 HP 3 = 3 HP = ½ HP 1 = 1½ HP = HP 7 = ¾ HP 2 = 2 HP *Note: 1 / 3 HP Single Phase unit is supplied with ½ HP motor. MATERIAL DISCHARGE, HEAD AND SUCTION HOUSING C = Cast Iron S = Stainless Steel PUMP MODEL GB GALLONS PER MINUTE Note: Not recommended for operation beyond recommended range specified on H-Q curve. For critical application conditions consult factory. Note: Not all combinations of motor, impeller and seal options are available for every pump model. Please check with on non-cataloged numbers. PAGE

6 DIMENSIONS AND WEIGHTS FOR 6 HZ AND HZ PUMPS 6.7 MOUNTING PATTERN DIA Thru Typ..38 DIA Thru-(4) Holes.38 Wide Slot Typ Suction Port (Ref.) Outline of Bolt-On Foot Eyelets will accommodate.31 DIA. Hex Head Bolts for removable wall mounting L2 L3 (MAX.) 1" NPT Port (Discharge) L1 1" NPT Port (Suction) Typ DIA 1/4" NPT Plug DIA (MAX.) Bolt-On Foot Non-Footed Motor PAGE 6

7 DIMENSIONS AND WEIGHTS FOR 6 HZ PUMPS Size Stages L1 L2 HP L3 Max. Wt. Approx. Approx. Max. lbs GB ½ ¾ ½ GB ¾ ¾ GB ½ ¾ GB ½ ¾ GB ½ ½ GB DIMENSIONS AND WEIGHTS FOR HZ PUMPS Size Stages L1 L2 HP L3 Max. Wt. Approx. Approx. Max. lbs GB ½ ¾ ½ GB ¾ ¾ GB ½ GB ½ ¾ GB ½ GB PAGE 7

8 GB PERFORMANCE CURVES RPM: 3 CURVE NO. CN429R1 GB1 17 STAGE GB7 14 STAGE 1 8 GPM GB 9 STAGE GB3 7 STAGE RPM: 29 CURVE NO. CN7R1 GB1 19 STAGE GB7 16 STAGE GB 1 STAGE GB3 7 STAGE 1 7 GPM PAGE 8 1 2

9 7GB PERFORMANCE CURVES RPM: 3 CURVE NO. CN43R1 1 1 GPM 1 2 7GB1 16 STAGE GB7 13 STAGE 7GB 9 STAGE RPM: 29 CURVE NO. CN8R2 7GB1 18 STAGE 7GB7 1 STAGE 7GB 1 STAGE 1 8 GPM PAGE 9

10 1GB PERFORMANCE CURVES RPM: 3 CURVE NO. CN431R1 1GB2 17 STAGE 3 16 GPM 1 2 1GB1 1 STAGE GB1 1 STAGE 1GB7 8 STAGE RPM: 29 CURVE NO. CN9R1 1GB2 23 STAGE GB1 17 STAGE 1GB1 11 STAGE 3 16 GPM GB7 9 STAGE PAGE

11 18GB PERFORMANCE CURVES RPM: 3 CURVE NO. CN432R1 18GB3 1 STAGE 6 28 GPM GB2 13 STAGE GB1 9 STAGE 18GB1 7 STAGE 18GB7 STAGE RPM: 29 CURVE NO. CN6R1 18GB3 23 STAGE GPM GB2 16 STAGE 18GB1 12 STAGE 18GB1 8 STAGE PAGE 11

12 2GB PERFORMANCE CURVES RPM: 3 CURVE NO. CN433R1 2GB3 14 STAGE 8 33 GPM GB2 1 STAGE 2GB1 9 STAGE 2GB1 7 STAGE 1 1 2GB7 STAGE RPM: 29 CURVE NO. CN61R1 2GB3 21 STAGE 8 28 GPM GB2 14 STAGE 2GB1 1 STAGE 1 1 2GB1 7 STAGE 1 2GB7 STAGE PAGE

13 33GB PERFORMANCE CURVES RPM: 3 CURVE NO. CN679R GB 19 STAGE 33GB3 13 STAGE 33GB2 9 STAGE 33GB1 7 STAGE 33GB1 STAGE 1 43 GPM RPM: 29 CURVE NO. CN68R GBZ3 14 STAGE 33GBZ2 1 STAGE 33GBZ1 8 STAGE 33GBZ1 6 STAGE 1 38 GPM PAGE 13

14 ACCESSORIES HOSE HANDLE AM3- Discharge Hose ¾" male x ¾" female, 2 hose, 4 ft. section, flexible. AM4 Suction Hose ¾" female x ¾" female, 1 hose, 4 ft. section flexible. 4K42 Formed carbon steel handle is standard on 7GB WaterGun and can be ordered separately for use on other sizes. PRESSURE GUN AM2-2 Designed for use with WaterGun. Nozzle passes approximately.7 GPM at 14 lbs. pressure and provides a most effective angle spray. PIPE ADAPTER AM-1 ¾" male HT x 1" male NPT hose to pipe adapter, stainless steel. Converts suction and discharge to ¾" male NPT hose. PAGE 14

15 NOTES PAGE 1

16 Xylem 1) The tissue in plants that brings water upward from the roots; 2) a leading global water technology company. We re 12, people unified in a common purpose: creating innovative solutions to meet our world s water needs. Developing new technologies that will improve the way water is used, conserved, and re-used in the future is central to our work. We move, treat, analyze, and return water to the environment, and we help people use water efficiently, in their homes, buildings, factories and farms. In more than 1 countries, we have strong, long-standing relationships with customers who know us for our powerful combination of leading product brands and applications expertise, backed by a legacy of innovation. For more information on how Xylem can help you, go to Xylem, Inc East Bayard Street Ext., Suite A Seneca Falls, NY Phone: (866) Fax: (888) Goulds is a registered trademark of Goulds Pumps, Inc. and is used under license. 212 Xylem Inc. B-33GB July 212