SPECIFICATIONS FOR LCD MODULE

A M P I R E SPECIFICATIONS FOR LCD MODULE CUSTOMER CUSTOMER PART NO. AMPIRE PART NO. AM-128128RTNQW-D1H APPROVED BY DATE Approved For Specifications Approved For Specifications & Sample APPROVED BY CHECKED BY ORGANIZED BY Date : 2006/7/14 AMPIRE CO., LTD. 1

RECORD OF REVISION Revision Date Page Contents Editor 2005/05/12 - New Release 2005/05/17 15 Addition part list. 2005/05/17 8 Modify LED Brightness of main and sub. 2005/07/04 3 RoHS declaration. 2005/07/04 34 Modify Mechanical drawing. 2005/07/07 15 Modify Part List. 2005/07/07 34 Modify Mechanical drawing. 2005/07/26 35 Including SMD Drawing. 2005/07/26 37 Including BLU Drawing. 2005/07/26 38 Including Packing Condition. 2005/07/26 14 Modify Part List. 2005/07/28 14 Modify Part List. 2005/07/29 14 Modify Part List. 2005/08/29 14 Modify Part List. 2005/08/29 34 Modify Mechanical Drawing. 2005/08/29 33 Modify Circuit Drawing. 2005/08/30 34 Modify Mechanical Drawing. 2005/09/09 34 Modify Mechanical Drawing. 2005/09/14 14 Modify Part List. 2005/09/14 33 Modify Circuit Drawing. 2005/09/20 14 Modify Part List. 2005/09/20 34 Modify Mechanical Drawing. 2005/09/21 33 Modify Circuit Drawing 2005/09/21 14 Modify Part List 2005/09/26 34 Modify Mechanical Drawing. 2005/09/26 33 Modify Circuit Drawing 2005/09/26 14 Modify Part List. 2005/09/26 33 Modify Circuit Drawing 2005/09/26 14 Modify Part List 2005/10/03 34 Modify Mechanical Drawing. 2005/10/18 33 Modify Circuit Drawing 2005/10/18 14 Modify Part List. 2006/01/11 34 Modify Mechanical Drawing. 2006/02/13 39 Attach Tail FPC Drawing and Improve Action 2006/02/15 14 Modify Part List. 2006/04/19 14 Modify Part List.(C2,C39 10u/6.3V, 0805, 0.85t) 2006/07/14 14 Remove C16. Date : 2006/7/14 AMPIRE CO., LTD. 2

Contents Item Title Page 1 Features 4 2 Mechanical Specifications 5 3 Absolute Max. Ratings and Environment 5 4 Electrical Specifications 6 5 Optical Characteristics 7 6 Block Diagram 12 7 Part List 14 8 Interface Specifications 16 9 80-system 16-bit interface 17 10 Instruction Description 18 11 Timing Characteristic 22 12 Setup of Power Supply 24 13 Instruction Setup Flow 25 14 Quality and Reliability 27 15 Use Precautions 31 16 Circuit Drawing 33 17 Outline Dimension 34 18 SMD Drawing 35 19 BLU Drawing 37 20 Tail FPC Drawing and Improve Action 38 21 Packing Condition 40 Date : 2006/7/14 AMPIRE CO., LTD. 3

1 Features Main LCD 1.5 inch Amorphous-TFT-LCD (Thin Film Transistor Liquid Crystal Display) for mobile-phone or handy electrical equipments. The Main-LCD adopts one backlight with High brightness 3-lamps white LED. (1) Construction: 1.5 a-si color TFT-LCD, 96 64 Monochromatic FSTN LCD, B/E Chip, FPC, White LED Backlight and Flash LED. (2) Main LCD : 2.1 Amorphous-TFT 1.5 inch display, transmissive, Normally white type, 12 o clock. 2.2 128(RGB) 128 dots Matrix,1/128 Duty. 2.3 LCD controller is TL1771. 2.4 Real 262K colors display: 65K: Red-5bit, Green-6bit, Blue-5bit (16-bit interface) 262K: Red-6bit, Green-6bit, Blue-6bit (18-bit interface) (3) Sub LCD : 2.1 Monochromatic FSTN type, Transflective, Positive, 6 o clock view 2.2 96X64 dots matrix, 1/64 Duty. 2.3 Sub LCD controller is S6B0724. (4) 16-bit high speed bus interface and high speed RAM-write function. (5) Direct data display with display RAM. Main LCD Internal RAM capacity: 128 (5+6+5) 128/8=32,768bytes (6) MPU interface: 16 bits 80-serise parallel interface is available. (7) RoHS declaration. Date : 2006/7/14 AMPIRE CO., LTD. 4

2 Mechanical Specification Dimensions and weight Item Specifications Unit External shape dimensions * 31.4 (W) x 55.68(H) x 3.3 (D) Max. mm Main LCD Sub LCD Pixel pitch 0.204 (W) x 0.22 (H) mm Active area 26.112 (W) x 28.16 (H) mm Viewing area 28.3 (W) x 30.17 (H) mm Dot size 0.195 (W) x 0.21 (H) mm Dot pitch 0.21 (W) x 0.225 (H) mm Active area 14.385 (W) x 20.145 (H) mm Viewing area 16.8 (W) x 22.6 (H) mm Weight 9.75 g * This specification is about External shape on shipment from AMPIRE. 3 Absolute Max. Ratings and Environment 3-1 Absolute max. ratings Ta=25 o C GND=0V Item Symbol Min. Max. Unit Remarks Power Supply for Logic VCC VSS -0.3 +4.6 V Power Input Voltage Vci -0.3 +4.6 V Power Supply for LED backlight LED A LED K -0.5 +10.8 V Input voltage VIN -0.5 VDD+0.5 V 3-2 Environment Item Specifications Remarks Storage temperature Max. +80 o C Min. 30 o C Note 1: Non-condensing Operating temperature Max. +70 o C Min. -20 o C Note 1: Non-condensing Note 1:Ta +40 o C Max.85%RH Ta>+40 o C The max. humidity should not exceed the humidity with 40 o C 85%RH. Date : 2006/7/14 AMPIRE CO., LTD. 5

4 Electrical Specifications 4-1 Electrical characteristics of LCD (V DD =2.8V, Ta=25 o C) Item Symbol Conditions MIN. TYP. MAX. Unit IC power voltage V DD 2.4 2.8 3.0 V Power input voltage Vci 2.4-3.0 V Sub LCD driving voltage V DD -V5-20 o C 10.35 10.65 10.95 0 o C 10.22 10.52 10.82 25 o C 10.15 10.45 10.75 50 o C 10.10 10.40 10.70 70 o C 10.02 10.32 10.62 High-level input voltage V IHC 0.7V DD V cc V Low-level input voltage V ILC -0.3 0.3V cc V V Consumption current of VDD Consumption current of LED I DD Electric VR value =XXXXH - 2.5 4 ma I LED V LED =9.8V - 15 20 ma 4-2 LED back light specification Item Symbol Conditions MIN. TYP. MAX. Unit Forward voltage V f I f =15mA - 9.8 10.8 V Reverse voltage V r - - 12 V Forward current I f 2-chip serial 12 15 20 ma Power Consumption P BL I f =15mA - 147 - mw Uniformity (with L/G) - I f =15mA 80% *1 - - Luminous color Chip connection White 2 chip serial connection Min( P1 ~ P5) * Uniformity (LT): 100 80% Max( P1 ~ P5) Date : 2006/7/14 AMPIRE CO., LTD. 6

5 Optical Characteristics Main LCD 5-1 Optical characteristics Driving codition:1/128 Duty LED backlight transmissive module: Item Symbol Temp. Min. Std. Max. Unit Conditions Tr 25 o C - 12.5 - θ=0 o,φ=0 o Response time ms Tf 25 o C - 12.5 - (Note 2) Contrast ratio CR 25 o C TBD TBD - - Transmittance T 25 o C - 7 - % θ=0 o, φ=0 o LED:ON, LIGHT:OFF (Note 4) Visual angle range front and rear θ 25 o C (θf) 15 (θb) 35 Degree φ= 0 o, CR 10 LED:ON LIGHT:OFF (Note 3) Visual angle range left and right θ 25 o C (θl) 45 (θr) 45 Degree φ=90 o, CR 10 LED:ON LIGHT:OFF (Note 3) Visual angle direction priority 12:00 (Note 5) Brightness 150 Cd/m2 V LED =9.8V, 15mA Full White pattern Date : 2006/7/14 AMPIRE CO., LTD. 7

5-2 CIE (x, y) chromaticity (1/128 Duty Ta = 25 C) Main LCD: (1/128 Duty Ta = 25 C) Item Symbol Transmissive Min. Std. Max. Conditions Red Green Blue White x 0.563 0.603 0.643 y 0.304 0.344 0.384 x 0.281 0.321 0.361 y 0.497 0.537 0.577 x 0.098 0.138 0.178 y 0.121 0.161 0.201 x 0.275 0.315 0.355 y 0.306 0.346 0.386 θ=0,φ=0 θ=0,φ=0 θ=0,φ=0 θ=0,φ=0 Light source Item Symbol Value Min. Std. Max. Conditions Light source Main LCD brightness Sub LCD brightness x 0.28 0.315 0.34 y 0.28 0.305 0.34 2300-180 θ=0,φ=0 Unit: cd/m 2 (I LED =15mA) Unit: cd/m 2 (I LED =15mA) Date : 2006/7/14 AMPIRE CO., LTD. 8

Sub LCD 5-3 Optical characteristics Driving codition:1/64 Duty, 1/9 Bias LED backlight transflective module: Response time Item Symbol Condition Min. Std. Max. Unit Note tr tf 25 C - - 200 200 - - ms ms Note2 Contrast ratio CR T.B.D 7 - Note4 Visual angle range Visual angle direction priority θ f - 40 - θ b - 35-25 C, CR 2 θ l - 35 - θ r - 35 - Degree Note3 - - 12:00 Note5 Frame Frequency f F 25 C 70 Hz Brightness - V LED =9.8V, 15mA 60 Cd/m 2 Date : 2006/7/14 AMPIRE CO., LTD. 9

NOTE 1: Optical characteristic measurement system Ring light LCD module Brightness gauge BM-7 (Topcon) LCD Glass fiber LED:OFF, LIGHT:ON Optical Detector Metal halide lamp Brightness gauge BM-7 (Topcon) LED LED:ON, LIGHT:OFF NOTE 2: Response tome definition Date : 2006/7/14 AMPIRE CO., LTD. 10

NOTE 3: φ θ definition NOTE 4: Contrast definition NOTE 5 : Visual angle direction priority 12 : 00 9 : 00 8 8 8 8 3 : 00 6 : 00 Date : 2006/7/14 AMPIRE CO., LTD. 11

6 Block Diagram Block diagram (Main LCD) Display format: Color-TFT transmissive, 12 o clock. Display mode: Normally white Display composition: 128 x RGB x 128 pixels LCD Driver : TL1771 Back light: White LED x 3 (I LED =15mA) 1.5" TFT LCD Panel 128(RGB)X128 pixels TL1771 & Driving Circuit LED Driver IC VCC GND /RESET /CS RS /RD /WR D[0:15] V_PWR MLCD_BRGT GND Date : 2006/7/14 AMPIRE CO., LTD. 12

Block diagram (Sub LCD) Display format: FSTN, Transflective type, Positive, 6 o clock. Display composition: 96 x 64 dots LCD Driver : S6B0724 Back light: White (Share Main LED backlight) 1 26 COM 63 S6B0724 COM32 SEG131 SEG95 COM31 COM0 SEG0 S1 DOT 1 S96 C1 C2 C33 96X64 DOTS LCD Panel C32 C64 Block diagram (Whole Module) Date : 2006/7/14 AMPIRE CO., LTD. 13

7 Part List Main LCD No. BOM code (part No.) Name and Description Maker Q ty Location Mark 01 128128R TFT-LCD HannStar 1 02 TL1771 LCD Driver IC Tomato 1 03 128128RFPC Main-FPC UniFlex 1 04 1100105058 Chip Resistor 100K(0402) Ever co. 1 R1 05 1100105401 Chip Cap 1u/10V (0603) Ever co. 5 C1,C2,C5,C10,C11 06 1200105301 Chip Cap 1u/6.3V (0402) Ever co. 6 C3,C4,C6,C7,C8,C9 07 1200104402 0.1u/16V 4 Ever co. 1 CA1 Sub LCD No. BOM code (part No.) Name and Description Maker Q ty Location Mark 01 09664D Monochromatic -LCD Lin Yo 1 02 S6B0724 LCD Driver IC Samsung 1 03 09664DFPC Sub-FPC Ever co. 1 PCB No. BOM code (part No.) Name and Description Maker Q ty Location Mark 01 128128R-D1 PCB APCP 1 02 1100221301 Chip Resistor 220R (0402) Ever co. 1 R1 03 1100220301 Chip Resistor 22R (0402) Ever co. 1 R8 04 1100470301 Chip Resistor 4.7k (0402) Ever co. 2 R10,R21 05 1100105301 Chip Resistor 1M (0402) Ever co. 1 R26 06 1100470301 Chip Resistor 47R (0402) Ever co. 1 R28 07 1100000301 Chip Resistor 0R (0402) Ever co. 2 R35,R36 08 1100123501 DNP 1 R42 09 1100240001 Chip Resistor 24R (0603) Ever co. 1 R47 10 1100330001 Chip Resistor 33R (0603) Ever co. 1 R43 11 1100101001 Chip Resistor100R (0402) Ever co. 1 R2 12 1330100001 10uH Panasonic 1330100007(substitute) 10uH Murata 1 L4 13 1330100001 Chip Cap 1u/25V (0603) Ever co. 2 C1,C5 14 1200106241 Chip Cap 10u/6.3V (0805) Ever co. 3 C9,C29,C38 15 1200106242 Chip Cap 10u/6.3V 0.85t (0805) Ever co. 2 C2,C39 16 1200471081 Chip Cap 470p/16V (0402) Ever co. 2 C6,C7 17 1200105042 Chip Cap 1u/10V (0603) Ever co. 7 C14,C40,,C43,C33,C45,C46,C47 18 1200103305 Chip Cap 0.01u/10V (0402) Ever co. 2 C8,C17 19 1200104171 Chip Cap 0.1u/16V (0402) Ever co. 5 C11,C15, C30,C32,C34 20 1200475051 Chip Cap 4.7u/10V (0805) Ever co. 1 C41 21 1200225401 Chip Cap 2.2u/6.3V (0603) Ever co. 4 C12,C13,C42,C44 Date : 2006/7/14 AMPIRE CO., LTD. 14

22 1200225401 Chip Cap 2.2n/50V (0402) Ever co. 2 C3,C4 23 1325510001 RB551V-30 promate 4 D8,D1,D9,D10 24 1320130001 UDZS13B/13V promate 1 D11 25 1312301901 2SK3019 promate 3 Q1,Q2,Q3 26 1308121001 SM8121AH NPC 1 U2 27 RT9361BPE charge pump Richtek 1 U3 28 RT9182EPES Regulator Richtek 1 U4 29 RT9193-28PB Regulator Richtek 1 U5 30 MV3018SOK-G Back-End chip Mtekvision 1 U6 31 RTSW2400MG resonator TDK 1 X3 32 ATCP-S354TW Flash LED Alti 1 LED1 33 1601258132 connector 34 Pin ELCO 1 CN2 34 1601258962 connector 20 pin ELCO 1 CN1 35 1340650051 Bead 600ohm (0402) Siltron 2 L1,L2 36 1348405103 ESD-EMI filter Amotech 5 VF2,VF3,VF4,VF5,VF6 37 1862754001 Rubber (14mm 1.8mm 2.0mm) Jufo 2 38 1862754002 Rubber (6mm 2.0mm 16.0mm) Jufo 2 BLU No. BOM code (part No.) Name and Description Maker Q ty Location Mark 01 3A25865701 Black Tape 3M 1 02 2A54132501 Diffuser 3M 1 03 3560404332 2-thin BEF 3M 1 04 3544330435 Light Guide 3M 1 05 8D34140221 Reflective 3M 1 06 3144145201 Housing Tai Fa 1 07 5415131763 LED Yuhsin 2 Tail FPC No. BOM code (part No.) Name and Description Maker Q ty Location Mark 01 1500121289 Tail FPC UniFlex 1 02 1601258131 connector 34 Pin ELCO 1 03 1651288132 connector 34 Pin LG 1 Date : 2006/7/14 AMPIRE CO., LTD. 15

8 Interface Specifications Pin No. Terminal Functions 1 DB15 2 DB14 3 DB13 4 DB12 Data Bus for 16-bits (high 8bit), 80-series MPU 5 DB11 6 DB10 7 DB9 8 DB8 9 DB7 Data Bus for 16-bits (low 8bit), 80-series MPU 10 MLCD_CS_N Chip select of main LCD (TL1771) 11 DIM LED B/L Dimming Control pin. 12 C_RD Read pin of B/E IC 13 LCM_BYPASS LCM BYPASS mode pin 14 LIGHT_EN Flash LED Enable 15 A2 Address pin of B/E IC 16 SPK/REC+ Speaker (+) 17 SPK/REC- Speaker (-) 18 INDUCTOR Enable pin of flash LED driver circuit 19 MLCD_BRGT Power on Main & Sub Back Light simultaneously 20 MOTOR Vibrator terminal 21 V_MSMP System Power For Main (VCC) & Sub LCD (VDD) 22 RESOUT_N Main & Sub LCD Reset terminal, active L 23 GND GND-terminal for analog circuit 24 LWR_N Low_Byte Write clock terminal, active L. ( 80 series interface ) 25 A1 Command/data select input terminal. Data with H, and command with L 26 DB6 27 DB5 28 DB4 29 DB3 Data Bus for 16-bits (low 8bit), 80-series MPU 30 DB2 31 DB1 32 DB0 33 GND GND-terminal for analog circuit 34 VPWR Battery power input for LED driver Date : 2006/7/14 AMPIRE CO., LTD. 16

9 80-system 16-bit interface 80-system 16-bit parallel data transmission is executed by setting IM2/1/0 pins to GND/Vcc/GND levels respectively. Data format for 16-bit interface Data format for 16-bit interface Date : 2006/7/14 AMPIRE CO., LTD. 17

10 Instruction Description Instruction List Driver IC: TL1771 Reg. No. Register R/W RS Upper Code Lower Code IB15 IB14 IB13 IB12 IB11 IB10 IB9 IB8 IB7 IB6 IB5 IB4 IB3 IB2 IB1 IB0 IR Index W 0 * * * * * * * * * ID6 ID5 ID4 ID3 ID2 ID1 ID0 SR Status read R 0 L7 L6 L5 L4 L3 L2 L1 L0 0 0 0 0 0 0 0 0 R00h Oscillation Start W 1 * * * * * * * * * * * * * * EXT OSC Device code read R 1 0 0 0 1 0 1 1 1 0 1 1 1 0 0 0 1 01h Driver output control W 1 0 0 0 0 EPL SM GS SS 0 0 0 0 NL3 NL2 NL1 NL0 02h LCD driving waveform control W 1 0 0 0 0 0 0 F/L 0 0 0 0 0 0 0 0 0 03h Entry mode W 1 0 0 DIT BGR 0 0 0 0 0 0 I/D1 I/D0 AM 0 0 0 04h 05h 06h 07h Display control 1 W 1 0 0 0 PT1 PT0 0 0 SPT 0 0 GON DTE CL REV D1 D0 08h Display control 2 W 1 0 0 0 0 FP3 FP2 FP1 FP0 0 0 0 0 BP3 BP2 BP1 BP0 09h 0Ah 0Bh Frame cycle control W 1 0 0 0 0 0 0 0Ch External display interface control 10h Power control 1 W 1 0 0 11h Power control 2 W 1 0 0 0 DIV 1 DIV 0 0 0 0 0 W 1 0 0 0 0 0 0 0 RM 0 0 DM1 DM0 0 0 0 RIM SAP 2 RTN 3 RTN 2 RTN 1 RTN 0 SAP SAP BT2 BT1 BT0 DC2 DC1 DC0 AP2 AP1 AP0 SLP STB 1 0 VRN VRN VRN VRN VRN VRP VRP VRP VRP VRP 0 0 0 14 13 12 11 10 14 13 12 11 10 12h Power control 3 W 1 0 0 0 0 0 0 0 0 0 0 0 0 0 VC2 VC1 VC0 13h Power control 4 W 1 0 0 0 0 14h Power control 5 W 1 0 0 15h ~ 1Fh VCO MG VDV 4 VC MR VDV 3 VRH VRH VRH VRH 0 0 0 0 0 0 PON 3 2 1 0 VDV VDV VDV VC VC VC VC VC 0 0 0 2 1 0 M4 M3 M2 M1 M0 : Setting disable Date : 2006/7/14 AMPIRE CO., LTD. 18

Driver IC: TL1771 Reg. No. 21h 22h Register RAM address register R/W RS Upper Code Lower Code IB15 IB14 IB13 IB12 IB11 IB10 IB9 IB8 IB7 IB6 IB5 IB4 IB3 IB2 IB1 IB0 W 1 AD15-8 (Upper) AD7-0 (Lower) RAM data write W 1 Write Data (Upper) Write Data (Lower) RAM data read R 1 Read Data (Upper) Read Data (Lower) 23h ~ 2Fh 30h Gamma control (1) W 1 0 0 0 0 0 31h Gamma control (2) W 1 0 0 0 0 0 32h Gamma control (3) W 1 0 0 0 0 0 33h Gamma control (4) W 1 0 0 0 0 0 34h Gamma control (5) 0 1 0 0 0 0 0 35h Gamma control (6) 0 1 0 0 0 0 0 36h Gamma control (7) 0 1 0 0 0 0 0 37h Gamma control (8) 0 1 0 0 0 0 0 38h Power control 6 W 1 0 0 0 0 39 VRN 03 PKP 12 PKP 11 PKP 10 PKP PKP PKP 32 31 30 PKP PKP PKP 52 51 50 PRP PRP1 PRP 12 1 10 PKN PKN PKN 12 11 10 PKN PKN PKN 32 31 30 PKN PKN PKN 52 51 50 PRN PRN PRN 12 11 10 VRN VRN VRN 02 01 00 0 0 0 0 0 PKP PKP PKP 02 01 00 0 0 0 0 0 PKP PKP PKP 22 21 20 0 0 0 0 0 PKP PKP PKP 42 41 40 0 0 0 0 0 PRP PRP PRP 02 01 00 0 0 0 0 0 PKN PKN PKN 02 01 00 0 0 0 0 0 PKN PKN PKN 22 21 20 0 0 0 0 0 PKN PKN PKN 42 41 40 0 0 0 0 0 PRN PRN PRN 02 01 00 0 0 0 0 VRP VRP VRP VRP 03 02 01 00 ~ 3F 40 Gate scan position register 41 W 1 42 43 44 45 W 1 0 0 0 0 0 0 0 0 0 0 0 1 st screen driving position W 1 SE17 SE16 SE15 SE14 SE13 SE12 SE11 SE10 SS17 SS16 SS15 SS14 SS13 SS12 SS11 SS10 2 nd screen driving position W 1 SE27 SE26 SE25 SE24 SE23 SE22 SE21 SE20 SS27 SS26 SS25 SS24 SS23 SS22 SS21 SS20 Horizontal window HEA HEA HEA HEA HEA HEA HEA HEA HSA HSA HSA HSA HSA HSA HSA HSA W 1 address 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 Vertical window VEA VEA VEA VEA VEA VEA VEA VEA VSA VSA VSA VSA VSA VSA VSA VSA W 1 address 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 SCN 4 SCN 3 SCN 2 SCN 1 SCN 0 : Setting disable Date : 2006/7/14 AMPIRE CO., LTD. 19

Reset Function If the /RESET input becomes L or the reset command is input, the internal timing generator is initialized. Must be reset after the power is supplied. The time required for the /RESET input is at least 1ms. When the power supply is reset while the power supply is ON, wait at least 10ms after the power has been supplied until the RC oscillation frequency become stabilized. While waiting, do not make initial settings for the instruction set, nor access to the GRAM. Register Start oscillation Driver output control LCD driving AC control Power control 1 Power control 2 Power control 6 Entry mode set Display control 1 Display control 2 Frame cycle control External display interface Power control 3 Power control 4 Power control 5 RAM address set Gamma control Initial State of Instructions Executed NL3-0= 110, SS= 0, CS= 0, GS= 0, SM= 0, EPL= 0, F/L= 0 SAP2-0= 000, BT2-0= 000, DC2-0= 000,AP2-0= 000 : LCD power off, STB= 0 : Standby mode off VRN14-0= 00000, VRP14-0= 00000 VRN03-0= 0000, VRP03-0= 0000 I/D1-0= 11 : Increment by 1, AM= 0 : Horizontal direction BGR= 0 PT1-0= 00, SPT= 0, GON= 0, TTD= 0, CL= 0 : 65k-color mode REV= 0, D1-0= 00 : Display off FP3-0= 0101, BP3-0= 0011 DIV1-0= 00 : 1-divided clock TRB3-0= 0000 : 16-clock in 1H period RIM= 0 : 16-bit RGB interface DM1-0= 00 : operated by internal clock RM= 0 : system interface VC2-0= 000 VCRMR= 1, PON= 0, VRH3-0= 0000 VCOMG= 0, VDV4-0= 00000, VCM4-0= 00000 AD15-0= 0000h PKP02-00= 000, PKP12-10= 000, PKP22-20= 000, PKP32-30= 000 PKP42-40= 000, PKP52-50= 000, PRP02-00= 000, PRP12-10= 000 PKN02-00= 000, PKN12-10= 000, PKN22-20= 000, PKN32-30= 000 PKN42-40= 000, PKN52-50= 000, PRN02-00= 000, PRN12-10= 000 Gate scan starting position SCN4-0= 00000 Date : 2006/7/14 AMPIRE CO., LTD. 20

Register Initial State of Instructions 1st screen division SE17-10= 1001 1111, SS17-10= 0000 0000 2nd screen division SE27-20= 1001 1111, SS27-20= 0000 0000 Horizontal RAM address position Vertical RAM address position HEA7-0= 0111 1111, HSA7-0= 0000 0000 VEA7-0= 1001 1111, VSA7-0= 0000 0000 Date : 2006/7/14 AMPIRE CO., LTD. 21

11 Timing Characteristics 80-system Bus interface Timing Characteristics (Main LCD) IOVCC=1.7V to 2.0V, VCC=2.4 to 3.0V (Ta=25 o C VCC = 2.2~2.4V) Item Symbol Min.. Typ. Max. Unit Bus cycle time Write t CYCW 100 - - ns Read t CYCR 250 - - ns Write low-level pulse width PW LW 40 - - ns Read low-level pulse width PW LR 150 - - ns Write high-level pulse width PW HW 40 - ns Read high-level pulse width PW HR 100 - ns Write/Read rise/fall time t WRr, t WRf - - 25 ns Set up time (RS to CSB, WRB) Write 0 - - ns Read t AS 10 - - ns Address hold time t AH 2 - - ns Write data set up time t DSW 25 - - ns Write data hold time t H 5 - - ns Read data delay time t DDR - - 100 ns Read data hold time t DHR 5 - - ns Date : 2006/7/14 AMPIRE CO., LTD. 22

80-system Bus interface Timing Characteristics (Sub LCD) RS tas80 tah80 tcy80 /RD, /W R CSB 0.9VDD 0.1VDD tpw L tds80 tdh80 tpw H DB0 to DB7 ( W rite ) DB0 to DB7 ( Read ) tacc80 tod80 Read / Write Characteristics (80-series MPU) (VDD = 2.7V, Ta = -40 ~ +85 C) Item Signal Symbol Condition Min. Max. Unit Address setup time Address hold time RS t AS80 t AH80 0 0 - - ns System cycle time for write System cycle time for read t CY80 t CY80 100 166 - ns Pulse width low Pulse width high /WR /RD t PWL t PWH 40 40 - - ns Data setup time Data hold time Read access time Output disable time DB0 to DB7 t DS80 t DH80 t ACC80 t OD80 CL = 100 pf NOTE: *1. The input signal rise time and fall time (tr, tf) is specified at 15 ns or less. (tr + tf) < (tcy80 - t PWLW - t PWHW ) for write, (tr + tf) < (tcy80 - t PWLR - t PWHR ) for read 30 5 15 10 - - - 50 ns ns Date : 2006/7/14 AMPIRE CO., LTD. 23

12 Setup of Power Supply The following show the sequence regarding power ON and OFF. Follow these sequence when executing display ON/OFF, standby set/off, sleep set/off. Power supply ON/OFF sequence Date : 2006/7/14 AMPIRE CO., LTD. 24

13 Instruction Setup Flow Display ON/OFF flow [Display OFF] [Display ON] Display OFF GON="1", DTE=1 PT="10" D1-0="10" Power Supply Setting CL=0 Wait (more then 2Frame) Display OFF GON="1", DTE=1 PT="10" D1-0="00" Display ON PT="10" GON="1", DTE=1 D1-0="01" Wait (more then 2Frame) Power Supply OFF SAP2-0="000" AP2-0="10" PON="0" GON="0", DTE="0" Display OFF Display ON GON="1", DTE=1 D1-0="10" Wait (more then 2Frame) Display ON GON="1", DTE=1 D1-0="11" Display OFF Date : 2006/7/14 AMPIRE CO., LTD. 25

Standby, Sleep mode set/release [Standby mode] [Sleep mode] Display Operation D="10" Standby Set Display Operation D="10" Sleep Set Standby set(stb="1") Sleep set(slp="1") Continue more thean 5 frame Continue more thean 5 frame Standby release(stb="0") Sleep release(slp="0") Wait more than 2 frame Standby release Wait more than 2 frame Sleep release D="11" D="11" Operation Operation Date : 2006/7/14 AMPIRE CO., LTD. 26

14 Quality and Reliability 14.1 TEST CONDITIONS Tests should be conducted under the following conditions : Ambient temperature : 25 ± 5 C Humidity : 60 ± 25% RH. 14.2 SAMPLING PLAN Sampling method shall be in accordance with MIL-STD-105E, level II, normal single sampling plan. 14.3 ACCEPTABLE QUALITY LEVEL A major defect is defined as one that could cause failure to or materially reduce the usability of the unit for its intended purpose. A minor defect is one that does not materially reduce the usability of the unit for its intended purpose or is an infringement from established standards and has no significant bearing on its effective use or operation. 14.4 APPEARANCE An appearance test should be conducted by human sight at approximately 30 cm distance from the LCD module under flourescent light. The inspection area of LCD panel shall be within the range of following limits. ZONE A active area ZONE B viewing area 14.5 NSPECTION QUALITY CRITERIA No. Item Criterion for defects Defect type 1 Non display No non display is allowed Major 2 Irregular operation No irregular operation is allowed Major 3 Short No short are allowed Major 4 Open Any segments or common patterns that don t activate are rejectable. Major Date : 2006/7/14 AMPIRE CO., LTD. 27

Size D (mm) Acceptable number 5 Black/White spot (I) D < 0.15 0.15 < D < 0.20 0.20 < D < 0.30 Ignore 3 2 Minor 0.30 < D 0 Length(mm) Width (mm) Acceptable number 6 Black/White line (I) 10 < L 5.0 < L <10 1.0 < L < 5.0 0.03 < W < 0.04 0.04 < W < 0.06 0.06 < W < 0.07 5 3 2 Minor L < 1.0 0.07 < W < 0.09 1 Size D (mm) Acceptable number 7 Black/White sport (II) D < 0.30 0.30 < D < 0.50 0.50 < D < 1.20 Ignore 5 3 Minor 1.20 < D 0 Black/White 8 line (II) 9 Back Light Length (mm) Width (mm) Acceptable number 20 < L 10 < L < 20 5.0 < L < 10 L < 5.0 0.05 < W < 0.07 0.07 < W < 0.09 0.09 < W < 0.10 0.10 < W < 0.15 5 3 2 1 1. No Lighting is rejectable 2. Flickering and abnormal lighting are rejectable Minor Major 10 Display pattern Unit:mm Minor A + B 0.30 2 D + E 0 < C 0.25 2 F + G 0.25 2 Note: 1. Acceptable up to 3 damages 2. NG if there re to two or more pinholes per dot Date : 2006/7/14 AMPIRE CO., LTD. 28

11 Blemish & Foreign matters Size: Size D (mm) D < 0.15 0.15 < D < 0.20 Acceptable number Ignore 3 Minor D = A + B 2 0.20 < D < 0.30 0.30 < D 2 0 Width (mm) Length (mm) Acceptable number 12 Scratch on Polarizer W<0.03 0.03<W<0.05 0.05<W<0.08 Ignore L < 2.0 L > 2.0 L > 1.0 Ignore Ignore 1 1 Minor L < 1.0 Ignore 0.08<W Note (1) Note(1) Note(1) Regard as a blemish Size D (mm) Acceptable number 13 Bubble in polarizer D < 0.20 0.20 < D < 0.50 Ignore 3 Minor 0.50 < D < 0.80 2 0.80 < D 0 14 Stains on LCD panel surface Stains that cannot be removed even when wiped lightly with a soft cloth or similar cleaning too are rejectable. Minor 15 Rust in Bezel Rust which is visible in the bezel is rejectable. Minor Defect of land 16 surface contact (poor Evident crevices which is visible are rejectable. Minor soldering) 17 Parts mounting 18 Parts alignment 1. Failure to mount parts 2. Parts not in the specifications are mounted 3. Polarity, for example, is reversed 1. LSI, IC lead width is more than 50% beyond pad outline. 2. Chip component is off center and more than 50% of the leads is off the pad outline. Major Major Major Minor Minor Date : 2006/7/14 AMPIRE CO., LTD. 29

19 Conductive foreign matter (Solder ball, Solder chips) 1. 0.45<φ,N 1 2. 0.30<φ<0.45,N 1 φ:average diameter of solder ball (unit: mm) 3. 0.50<L,N 1 L: Average length of solder chip (unit: mm) Major Minor Minor 1. Due to PCB copper foil pattern burnout, the pattern is 20 Faulty PCB correction connected, using a jumper wire for repair; 2 or more places are corrected per PCB. 2. Short circuited part is cut, and no resist coating has been Minor Minor performed. 14.6 Reliability Test Item Test Conditions Note High Temperature Operation 70±3 C, t=96 hrs Low Temperature Operation -20±3 C, t=96 hrs High Temperature Storage 80±3 C, t=96 hrs 1,2 Low Temperature Storage -30±3 C, t=96 hrs 1,2 Humidity Test 40 C, Humidity 90%, 96 hrs 1,2 Thermal Shock Test Vibration Test (Packing) Static Electricity -30 C ~ 25 C ~ 80 C 30 min. 5 min. 30 min. ( 1 cycle ) Total 5 cycle Sweep frequency:10~55~10 Hz/1min Amplitude : 0.75mm Test direction : X.Y.Z/3 axis Duration : 30min/each axis 150pF 330 ohm +8kV, 10times air discharge 1,2 2 Note 1 : Condensation of water is not permitted on the module. Note 2 : The module should be inspected after 1 hour storage in normal conditions (15-35 C, 45-65%RH). Definitions of life end point : Current drain should be smaller than the specific value. Function of the module should be maintained. Appearance and display quality should not have degraded noticeably. Contrast ratio should be greater than 50% of the initial value. Date : 2006/7/14 AMPIRE CO., LTD. 30

15 Use Precautions 15.1 Handling precautions 1) The polarizing plate may break easily so be careful when handling it. Do not touch, press or rub it with a hard-material tool like tweezers. 2) Do not touch the polarizing plate surface with bare hands so as not to make it dirty. If the surface or other related part of the polarizing plate is dirty, soak a soft cotton cloth or chamois leather in benzine and wipe off with it. Do not use chemical liquids such as acetone, toluene and isopropyl alcohol. Failure to do so may bring chemical reaction phenomena and deteriorations. 3) Remove any spit or water immediately. If it is left for hours, the suffered part may deform or decolorize. 4) If the LCD element breaks and any LC stuff leaks, do not suck or lick it. Also if LC stuff is stuck on your skin or clothing, wash thoroughly with soap and water immediately. 15.2 Installing precautions 1) To prevent breaking by static electricity from the human body and clothing, earth the human body properly using the high resistance and discharge static electricity during the operation. In this case, however, the resistance value should be approx. 1MΩ and the resistance should be placed near the human body rather than the ground surface. When the indoor space is dry, static electricity may occur easily so be careful. We recommend the indoor space should be kept with humidity of 60% or more. When a soldering iron or other similar tool is used for assembly, be sure to earth it. 2) When installing the module and ICs, do not bend or twist them. Failure to do so may crack LC element and cause circuit failure. 3) To protect LC element, especially polarizing plate, use a transparent protective plate (e.g., acrylic plate, glass etc) for the product case. 4) Do not use an adhesive like a both-side adhesive tape to make LCD surface (polarizing plate) and product case stick together. Failure to do so may cause the polarizing plate to peel off. 15.3 Storage precautions 1) Avoid a high temperature and humidity area. Keep the temperature between 0 C and 35 C and also the humidity under 60%. 2) Choose the dark spaces where the product is not exposed to direct sunlight or fluorescent light. 3) Store the products as they are put in the boxes provided from us or in the same conditions as we recommend. Date : 2006/7/14 AMPIRE CO., LTD. 31

15.4 Operating precautions 1) Do not boost the applied drive voltage abnormally. Failure to do so may break ICs. When applying power voltage, check the electrical features beforehand and be careful. Always turn off the power to the LC module controller before removing or inserting the LC module input connector. If the input connector is removed or inserted while the power is turned on, the LC module internal circuit may break. 2) The display response may be late if the operating temperature is under the normal standard, and the display may be out of order if it is above the normal standard. But this is not a failure; this will be restored if it is within the normal standard. 3) The LCD contrast varies depending on the visual angle, ambient temperature, power voltage etc. Obtain the optimum contrast by adjusting the LC dive voltage. 4) When carrying out the test, do not take the module out of the low-temperature space suddenly. Failure to do so will cause the module condensing, leading to malfunctions. 5) Make certain that each signal noise level is within the standard (L level: 0.2Vdd or less and H level: 0.8Vdd or more) even if the module has functioned properly. If it is beyond the standard, the module may often malfunction. In addition, always connect the module when making noise level measurements. 6) The CMOS ICs are incorporated in the module and the pull-up and pull-down function is not adopted for the input so avoid putting the input signal open while the power is ON. 7) The characteristic of the semiconductor element changes when it is exposed to light emissions, therefore ICs on the LCD may malfunction if they receive light emissions. To prevent these malfunctions, design and assemble ICs so that they are shielded from light emissions. 8) Crosstalk occurs because of characteristics of the LCD. In general, crosstalk occurs when the regularized display is maintained. Also, crosstalk is affected by the LC drive voltage. Design the contents of the display, considering crosstalk. 15.5 Other 1) Do not disassemble or take the LC module into pieces. The LC modules once disassembled or taken into pieces are not the guarantee articles. 2) The residual image may exist if the same display pattern is shown for hours. This residual image, however, disappears when another display pattern is shown or the drive is interrupted and left for a while. But this is not a problem on reliability. Date : 2006/7/14 AMPIRE CO., LTD. 32

16 Circuit Drawing 100 ohm D11 UDZS13B U3 RT9361BPE C 1 0 D N P C 16 D N P 2SK3019 2SK3019 C37 DNP C 3 2. 2 n C 4 2. 2 n Date : 2006/7/14 AMPIRE CO., LTD. 33

17 Outline Dimension 晶 采 光 電 科 技 Date : 2006/7/14 AMPIRE CO., LTD. 34

18 SMD Drawing Main FPC 晶 采 光 電 科 技 Date : 2006/7/14 AMPIRE CO., LTD. 35

PCB 晶 采 光 電 科 技 Date : 2006/7/14 AMPIRE CO., LTD. 36

19 BLU Drawing 晶 采 光 電 科 技 Note: 驅 動 :15mA VF: 6.6V Dice:2-LED Dice 均 勻 度 :80% 以 上 正 面 亮 度 : 2300cd/m2(Min.) 背 面 亮 度 : 180cd/m2(Min.) 正 反 共 用 同 一 個 背 光 FPC Base film: 1 mil polyimide+ 1/2 oz copper (One Layers) G/P 材 質 Date : 2006/7/14 AMPIRE CO., LTD. 37

20 Tail FPC Drawing and Improve Action Drawing 晶 采 光 電 科 技 5.G/P 材 質 Date : 2006/7/14 AMPIRE CO., LTD. 38

128128R-D1 (VT820) Tail FPC Improve Action 1. Improve Method: 0.3mm We suggest preserve 0.3 between pattern and edge, to prevent short and SMT cold solider. Date : 2006/7/14 AMPIRE CO., LTD. 39

21 Packing Condition 晶 采 光 電 科 技 Date : 2006/7/14 AMPIRE CO., LTD. 40