(An Autonomous Institution of the Department of Biotechnology, Govt. of India) N.C.C.S. Complex, Ganeshkhind, Pune University Campus, Pune 411007. PART-II (COMMERCIAL / PRICE BID) DESIGN, AND INSTALLATION OF CUSTOMIZED STEEL LAB FURNITURE.AT N.C.C.S., PUNE DUE DATE FOR SUBMISSION: 18/01/2016 @ 13 HRS TO BE SUBMITTED TO: The Director National Centre for Cell Science Savitribai Phule Pune University Campus, Pune 411007 (Maharashtra, India) NAME AND ADDRESS OF BIDDER:
(Pl referrer scope of work for detail specification in technical bid before quoting) 1 AND INSTALLATION OF WORKING ISLAND BENCH WITH TWO SHELF SUITABLE FOR BIOLOGICAL LABORATORY Nos. 2 REFERENCE DRAWING 1 Overall size- 7500mm(L)X1500mm(W)X 2000mm(H) Having five module workstations of following details: Granite work top jet black colour having 18-20mm thick, with 3mm thick new print rubber support, approximate size 1500mmL X 1500mmW X 900mm table height and 2000mm overall height of vertical, with heavy duty adjustable levelers, with suitable size of heavy duty Aluminum extrusion section of suitable size duly powder coated and C Bracket frame of min 2.5mm thick CRCA powder coated supporting frame having smooth and finish edges, with two storage unit each having overall size 500mmL X 500mmD X approx 660mmH having one drawer, one door and one shelf with locking arrangement and smooth finished side edges with suitable size of aluminum powered coated handles, with two adjustable shelf of full length of total width of 450mm, GI polyester powder coated metallic finish suitable for UDL of 70 kg with necessary supports etc., having one service drop for electrical power cabling from false ceiling at appropriate place as per site condition requirement preferably at the centre of the workstation, with necessary three nos. of electrical power outlets of 5/15A ratings of combined switch sockets on both side total six nos on proper detachable modular mounting of IP55 with one DP MCB of 32A capacity duly wired of 2.5sqmm copper multistrand wire for catering distribution of electrical supply for five module units and provide proper Tubelight fitting of 18/20W both side for each module below storage shelf with switch duly wired etc. Complete. Page 1 of 7
2 AND INSTALLATION OF WORKING ISLAND BENCH WITH TWO SHELF SUITABLE FOR BIOLOGICAL LABORATORY No. 1 REFERENCE DRAWING 1 Overall size- 3600mm(L)X1500mm(W)X 2000mm(H) Having two module workstations of following details: Granite work top jet black colour having 18-20mm thick, with 3mm thick new print rubber support, approximate size 1800mmL X 1500mmW X 900mm table height, and 2000mm overall height of vertical, with heavy duty adjustable levelers, with suitable size of heavy duty Aluminum extrusion section of suitable size duly powder coated and C Bracket frame of min 2.5mm thick CRCA powder coated supporting frame having smooth and finish edges, with two storage unit each having overall size 500mmL X 500mmD X approx 660mmH having one drawer, one door and one shelf with locking arrangement and smooth finished side edges with suitable size of aluminum powered coated handles, with two adjustable shelf of full length of total width of 450mm, GI polyester powder coated metallic finish suitable for UDL of 70 kg with necessary supports etc., having one service drop for electrical power cabling from false ceiling at appropriate place as per site condition requirement preferably at the centre of the workstation, with necessary three nos. of electrical power outlets of 5/15A ratings of combined switch sockets on both side total six nos, on proper detachable modular mounting of IP55 with one DP MCB of 32A capacity duly wired of 2.5sqmm copper multistrand wire for catering distribution of electrical supply for two module units and provide proper Tubelight fitting of 18/20W both side for each module below storage shelf with switch duly wired etc. Complete. Page 2 of 7
3 AND INSTALLATION OF STUDENT READING TABLE REFERENCE DRAWING 2 Overall size- 7000mm(L) X 600mm(W)X1200mm(H) Having size of each module table 875mmL X 600mmW X 1200mmH total eight modules with 25mm thick commercial plywood Laminated top with 1.5mm thick melamine (on both sides) top with 2mm thk PVC edge binding fitted on heavy duty duly suitable size powder coated CRCA supporting frame, with 12mm thick frosted glass partition of height 600mmW X450mmH from table top with rounded corner with necessary fixing arrangement and having module type soft board and magnet board, appropriate size of foot rest. The table should have one single full length drawer of CRCA powder coated with appropriate frame and heavy duty telescopic channel, with powder coated handle with locking arrangement, heavy duty adjustable levelers. Electrical Raceway provided with two no of 5Amp combined switch and socket with necessary wiring, cable manager etc. 4 AND INSTALLATION OF STUDENT READING TABLE REFERENCE DRAWING 2 Overall size- 2625mm(L) X 600mm(W)X1200mm(H) Having size of each module table 875mmL X 600mmW X 1200mmH, total three modules with 25mm thick commercial plywood Laminated top with 1.5mm thick melamine (on both sides) top with 2mm thk PVC edge binding fitted on heavy duty duly suitable size powder coated CRCA supporting frame, with 12mm thick frosted glass partition of height 600mmW X450mmH from table top with rounded corner with necessary fixing arrangement and having module type soft board and magnet board, appropriate size of foot rest. The table should have one single full length drawer of CRCA powder coated with appropriate frame and heavy duty telescopic channel, with powder coated handle with locking arrangement, heavy duty adjustable levelers. Electrical Raceway provided with two no of 5Amp combined switch and socket with necessary wiring, cable manager etc. No 1 No. 1 Page 3 of 7
5 AND INSTALLATION OF STUDENT READING TABLE No. 1 REFERENCE DRAWING 2 Overall size- 1500mm(L) X 600mm(W)X1200mm(H) Having size of each module table 750mmL X 600mmW X 1200mmH, total two modules with 25mm thick commercial plywood Laminated top with 1.5mm thick melamine (on both sides) top with 2mm thk PVC edge binding fitted on heavy duty duly suitable size powder coated CRCA supporting frame, with 12mm thick frosted glass partition of height 600mmW X450mmH from table top with rounded corner with necessary fixing arrangement and having module type soft board and magnet board, appropriate size of foot rest. The table should have one single full length drawer of CRCA powder coated with appropriate frame and heavy duty telescopic channel, with powder coated handle with locking arrangement, heavy duty adjustable levelers. Electrical Raceway provided with two no of 5Amp combined switch and socket with necessary wiring, cable manager etc. 6 AND INSTALLATION OF WALL CUPBOARD i) Overall size 900mmLX300mmWX640mmH with framed openable 4mm thick glass shutters with hinges and handles. Nos. 8 REFERENCE DRAWING 3. ii) Overall size 750mmLX300mmWX640mmH Nos. 14 with framed openable 4mm thick glass shutters with hinges and handles. REFERENCE DRAWING 4. iii) Overall size 750mmLX 300mmWX640mmH without any shutters. REFERENCE DRAWING 5. Nos. 3 iv) Overall size 600mmLX300mmWX640mmH Nos. 4 with framed openable 4mm thick glass shutters with hinges and handles. REFERENCE DRAWING 6. Page 4 of 7
7 AND INSTALLATION OF ANTIVIBRATION TABLE REFERENCE DRAWING 7. Overall size 750mm(L) X 600mm(W) X 750mm(H) having 18-20mm thick Jet Black Granite work top to be placed on 3mm thick neoprene rubber sheet. Heavy duty 50mmX50mm, 16SWG CRCA Epoxy Powder coated frame having heavy duty appropriate size of adjustable levelers suitable for ant vibration table. 8 AND INSTALLATION OF GLASS DISPLAY CABINET No. 1 Nos. 5 REFERENCE DRAWING 8 Overall size: 1200mm(L) x 450mm(W) x 2000mm(H) Half height bottom openable CRCA powder coated two doors with handles and one CRCA powder coated shelf with locking arrangement. Half height top openable two 4mm thick glass shutters with handles and two CRCA powder coated adjustable shelves with locking arrangement. 9 AND INSTALLATION OF STORAGE UNIT (UNDER PLATFORM) i) Overall size- 500mm(L)x 500mm(D) x approx.750mm(h) having three drawers with twin type 4 castor wheels with provision locking of two front castor wheels. No. 10 REFERENCE DRAWING 9. ii) Overall size 600mm(L)x 500mm(D) x No. 1 approx.750mm(h) having one drawers, two doors and one adjustable shelf with twin type 4 castor wheels with provision locking of two front castor wheels. REFERENCE DRAWING 10. iii) Overall size 800mm(L)x 500mm(D) x No. 1 approx.750mm(h) having one drawers, two doors and one adjustable shelf with twin type 4 castor wheels with provision locking of two front castor wheels. REFERENCE DRAWING 10. iv) Overall size 900mm(L)x 500mm(D) x No. 6 approx.750mm(h) having one drawers, two doors and one adjustable shelf with twin type 4 castor wheels with provision locking of two front castor wheels. REFERENCE DRAWING 10. Page 5 of 7
v) Overall size 600mm(L)x 500mm(D) x No. 1 approx.750mm(h) having two doors and one adjustable shelf with twin type 4 castor wheels with provision locking of two front castor wheels. REFERENCE DRAWING 11 10 AND INSTALLATION OF No. 1 GENERAL PURPOSE FUMEHOOD REFERENCE DRAWING 12 Providing and Placing of 1500mm Auto bypass Bench top Fume Hoods with overall size of 1500 x 900 x 2200 mm. The working Volume shall be 1300x625x1200 mm with the bed size 1300x625 mm. The worktop height shall be 900 mm. Fume hoods shall be of complete KD (Knock down) construction with airfoil design to insure maximum operating efficiency. Foil sections at the front facials of the hood shall minimize eddying of air currents at the hood face and the rear baffle system shall minimize turbulence in the upper portion of the hood interior. It shall comprise of the following: Superstructure: i) Outer Casing: GI sheet with Epoxy Powder coating. ii) Liner: SS304. iii)vertical Type Sash with toughened glass iv)ss304 worktop. v) A soft touch button panel with main switch, switch for blower tube light & socket. vi) Electrical sockets & switches (230V, 6/16A, 50Hz) Nos. 04. vii) Remotely operated color coded three services (CA, Water, Nitrogen) with SS breaded flexible hose & brass fittings. a. Apparatus base storage cabinet for benchtop Knock Down Fume Hood MS powder coated with shelf and double skinned door with overall Size: 750W x 550D x 824H b. Chemical storage cabinet for benchtop Knock Down Fume Hood MS powder coated from outside and FRV Moulding from inside, with shelf and double skinned door of Size: 750W x 550D x 824 H. Page 6 of 7
11 Supply, fabrication, installation, balancing and commissioning of factory fabricated Polypropylene round ducting of dia 200mm complete with 3 mm Fibre glass wool coating for fire protection, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings, specifications & directions of Engineer-In- Charge RMT 25 12 Supply, fabrication, installation, balancing and commissioning of blower for fumehood as per site condition Job 1 Total (Rs.) Service Tax % on Installation Charges Grand Total Amount for supply, installation and commissioning (Rs.) Grand Total Amount in word ( ) Page 7 of 7