HEATER & AIR CONDITIONING CONTROL SYSTEM

VTITI, TR & IR ITIR STI TR & IR ITII TR SYST TTS UTTI IR ITII RUTI... 5 RUTIS... 5 recaution for Supplemental Restraint System (SRS) "IR " and "ST T R-T- SIR"...5 SYST SRITI... 6 T RTS... 6 RT UTTI IR ITII SYS- T...6 RT UTTI IR ITII SYS- T : omponent arts ocation...6 RT UTTI IR ITII SYS- T : omponent escription...7 RR UTTI IR ITII SYS- T...8 RR UTTI IR ITII SYS- T : omponent arts ocation...9 RR UTTI IR ITII SYS- T : omponent escription...10 S (V IT TR SYS- T)...10 S (V IT TR SYS- T) : omponent arts ocation...11 S (V IT TR SYS- T) : omponent escription...11 spirator...12 ront lower otor...12 Rear lower otor...13 Refrigerant ressure Sensor...13 SYST...14 RT UTTI IR ITII SYS- T...14 RT UTTI IR ITII SYS- T : System iagram...14 RT UTTI IR ITII SYS- T : System escription...14 RT UTTI IR ITII SYS- T : ir low ontrol...15 RT UTTI IR ITII SYS- T : ir Inlet ontrol...16 RT UTTI IR ITII SYS- T : ir utlet ontrol...17 RT UTTI IR ITII SYS- T : ompressor ontrol...17 RT UTTI IR ITII SYS- T : oor ontrol...18 RT UTTI IR ITII SYS- T : Temperature ontrol...21 RT UTTI IR ITII SYS- T : ail-safe...21 RR UTTI IR ITII SYS- T...22 RR UTTI IR ITII SYS- T : System iagram...23 RR UTTI IR ITII SYS- T : System escription...23 RR UTTI IR ITII SYS- T : ir low ontrol...24 RR UTTI IR ITII SYS- T : ir utlet ontrol...25 RR UTTI IR ITII SYS- T : oor ontrol...26 RR UTTI IR ITII SYS- T : Temperature ontrol...27 S (V IT TR SYS- T)...27 S (V IT TR SYS- T) : System iagram...28 S (V IT TR SYS- T) : System escription...28-1

S (V IT TR SYS- T) : utomatic Intake ontrol (xhaust as / utside dor etecting echanism)... 28 S (V IT TR SYS- T) : lasmacluster ontrol... 29 RTI... 30 RT UTTI IR ITII SYS- T... 30 RT UTTI IR ITII SYS- T : Switch ame and unction... 30 RR UTTI IR ITII SYS- T... 35 RR UTTI IR ITII SYS- T : Switch ame and unction... 35 S (V IT TR SYS- T)... 37 S (V IT TR SYS- T) : Switch ame and unction... 37 ISIS SYST (V)... 39 escription... 39 SUT-III unction... 39 U ISIS IRTI... 42 / UT.... 42 Reference Value... 42 ail-safe... 45 T Index... 45, I /R... 47 ist of U Reference... 47 WIRI IR... 48 UTTI IR ITII SYST... 48 Wiring iagram... 48 SI ISTI... 60 ISIS RIR WR W... 60 Work low... 60 RTI ISTI... 62 RT UTTI IR ITII SYS- T... 62 RT UTTI IR ITII SYS- T : Work rocedure... 62 RR UTTI IR ITII SYS- T... 64 RR UTTI IR ITII SYS- T : Work rocedure... 64 S (V IT TR SYS- T)... 66 S (V IT TR SYS- T) : Work rocedure... 66-2 SYST STTI... 68 RT UTTI IR ITII SYS- T... 68 RT UTTI IR ITII SYS- T : Temperature Setting Trimmer (ront)... 68 RT UTTI IR ITII SYS- T : oot osition Setting Trimmer... 68 RT UTTI IR ITII SYS- T : Inlet ort emory unction (R)... 69 RT UTTI IR ITII SYS- T : Inlet ort emory unction (R)... 69 RR UTTI IR ITII SYS- T... 69 RR UTTI IR ITII SYS- T : Temperature Setting Trimmer (Rear)... 69 S (V IT TR SYS- T)... 70 S (V IT TR SYS- T) : xhaust as / utside dor etecting Sensor Sensitivity djustment unction... 70 S (V IT TR SYS- T) : uto Intake Switch Interlocking ovement hange unction... 70 T/IRUIT ISIS... 72 U1000 IRUIT... 72 escription... 72 T ogic... 72 iagnosis rocedure... 72 U1010 TR UIT ()... 73 escription... 73 T ogic... 73 iagnosis rocedure... 73 2578, 2579 RT I-VI SSR... 74 T ogic... 74 iagnosis rocedure... 74 omponent Inspection... 75 257, 257 IT SSR... 77 T ogic... 77 iagnosis rocedure... 77 omponent Inspection... 78 2581, 2582 IT SSR... 80 T ogic... 80 iagnosis rocedure... 80 omponent Inspection... 81 262, 262, 2657, 2658 XUST S/UTSI R TTI SSR... 83 T ogic... 83 iagnosis rocedure... 83

2630, 2631 SU SSR (RIVR SI)...86 T ogic...86 iagnosis rocedure...86 omponent Inspection...87 2632, 2633 RT IR IX R - TR (RIVR SI)...89 T ogic...89 iagnosis rocedure...89 2634, 2635 RT IR IX R - TR (SSR SI)...91 T ogic...91 iagnosis rocedure...91 2636, 2637, 2638, 2639, 2654, 2655 RT R TR...93 T ogic...93 iagnosis rocedure...93 263, 263, 263 IT R - TR...95 T ogic...95 iagnosis rocedure...95 2661, 2662, 2663 UR VTITR R TR...97 T ogic...97 iagnosis rocedure...97 2664, 2665 RR IR IX R TR...99 T ogic...99 iagnosis rocedure...99 2666, 2669, 266 RR R TR... 101 T ogic... 101 iagnosis rocedure... 101 2667, 2668 SU SSR (S- SR SI)... 103 T ogic... 103 iagnosis rocedure... 103 omponent Inspection... 104 266, 266 RR I-VI SSR.. 106 T ogic... 106 iagnosis rocedure... 106 omponent Inspection... 107 270 / UT.... 109 T ogic... 109 iagnosis rocedure... 109 WR SUY RU IRUIT... 110 / UT.... 110 / UT. : iagnosis rocedure... 110 RT IR IX R TR (RIVR SI)..110 RT IR IX R TR (RIVR SI) : iagnosis rocedure...110 RT IR IX R TR (SSR SI)...111 RT IR IX R TR (SSR SI) : iagnosis rocedure...111 RT R TR...112 RT R TR : iagnosis rocedure...112 IT R TR...113 IT R TR : iagnosis rocedure..113 RR IR IX R TR...114 RR IR IX R TR : iagnosis rocedure...114 RR / TR...115 RR / TR : iagnosis rocedure...115 RR R TR...116 RR R TR : iagnosis rocedure...116 UR VTITR R TR...116 UR VTITR R TR : iagnosis rocedure...116 R TR... 118 iagnosis rocedure...118 R TR UITI IRUIT. 120 iagnosis rocedure...120 RT WR TR... 121 iagnosis rocedure...121 omponent Inspection (ront lower otor)...122 omponent Inspection (lower Relay)...123 IIZR... 124 omponent unction heck...124 iagnosis rocedure...124 T UT... 126 omponent unction heck...126 iagnosis rocedure...126 RR / TR UITI SI... 127 iagnosis rocedure...127 RR / SI VV... 128 iagnosis rocedure...128 omponent Inspection...129 RR WR TR... 131 iagnosis rocedure...131 omponent Inspection...132 SYT ISIS... 133-3

RT UTTI IR ITII SYST... 133 iagnosis hart y Symptom...133 RR UTTI IR ITII SYST... 135 iagnosis hart y Symptom...135 S (V IT TR SYST)... 137 Symptom Table...137 ISUIIT I... 138 RT IR ITIR...138 RT IR ITIR : escription...138 RT IR ITIR : iagnosis rocedure...138 RR IR ITIR...139 RR IR ITIR : escription...139 RR IR ITIR : iagnosis rocedure..139 ISUIIT TI... 140 RT IR ITIR...140 RT IR ITIR : escription...140 RT IR ITIR : iagnosis rocedure...140 RR IR ITIR...140 RR IR ITIR : escription...141 RR IR ITIR : iagnosis rocedure..141 RSSR S T RT... 142 escription...142 iagnosis rocedure...142 RV ISTTI...144 RT / TR... 144 Removal and Installation...144 RR / TR... 145 Removal and Installation...145 / UT.... 146 Removal and Installation...146 IT SSR...147 Removal and Installation... 147 I-VI SSR...148 RT / UIT SSY... 148 RT / UIT SSY : Removal and Installation... 148 RR / UIT SSY... 148 RR / UIT SSY : Removal and Installation... 148 SU SSR...149 Removal and Installation... 149 IT SSR...150 xploded View... 150 Removal and Installation... 150 XUST S/UTSI R SSR..151 Removal and Installation... 151 R TR...152 xploded View... 152 R TR... 153 R TR : Removal and Installation. 153 IR IX R TR... 153 IR IX R TR : Removal and Installation... 153 IT R TR... 153 IT R TR : Removal and Installation... 153 UR VTITR R TR... 154 UR VTITR R TR : Removal and Installation... 154 RR R TR... 154 RR R TR : Removal and Installation... 154 RR IR IX R TR... 154 RR IR IX R TR : Removal and Installation... 154 IIZR...155 xploded View... 155 Removal and Installation... 155-4

RUTIS < RUTI > [UTTI IR ITII] RUTI RUTIS recaution for Supplemental Restraint System (SRS) "IR " and "ST T R-TSIR" II:0000000006275847 The Supplemental Restraint System such as IR and ST T R-TSIR, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. Information necessary to service the system safely is included in the SRS IR and ST T of this Service anual. WRI: To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision that would result in air bag inflation, all maintenance must be performed by an authorized ISS/IIITI dealer. Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. or removal of Spiral able and ir ag odule, see the SRS IR. o not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service anual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors. RUTIS W USI WR TS (IR R TRI) RS WRI: When working near the ir ag iagnosis Sensor Unit or other ir ag System sensors with the ignition or engine running, T use air or electric power tools or strike near the sensor(s) with a hammer. eavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury. When using air or electric power tools or hammers, always switch the ignition, disconnect the battery, and wait at least 3 minutes before performing any service. -5

T RTS < SYST SRITI > [UTTI IR ITII] SYST SRITI T RTS RT UTTI IR ITII SYST RT UTTI IR ITII SYST : omponent arts ocation II:0000000006275848 II0812ZZ 1. reset switch 2. ngine coolant temperature sensor Refer to -16, "omponent arts ocation". 4. Refer to -16, "omponent arts ocation" 3. I /R Refer to S-4, "omponent arts ocation". 5. Refrigerant pressure sensor 6. mbient sensor 7. agnet clutch 8. V control unit Refer to V-9, "omponent arts ocation". 9. ombination meter Refer to WI-6, "TR SYST : omponent arts ocation". 10. Sunload sensor 11. ront display 12. Upper ventilator door motor -6

T RTS < SYST SRITI > [UTTI IR ITII] 13. spirator 14. ront air mix door motor (river side) 15. Intake sensor 16. ront mode door motor 17. ront air mix door motor (assenger 18. Intake door motor side) 19. ront blower motor 20. / auto amp. 21. ront in-vehicle sensor. eft side of heater & cooling unit assemblsembly. Right side of heater & cooling unit as-. ack side of blower unit assembly. luster lid is removed. Instrument lower panel is removed RT UTTI IR ITII SYST : omponent escription II:0000000006275849 omponent mbient sensor V control unit / auto amp. ront blower motor lower unit Intake door motor ombination meter ngine coolant temperature sensor ront display ront in-vehicle sensor escription mbient sensor measures ambient air temperature. The sensor uses a thermistor which is sensitive to the change in temperature. The electrical resistance of the thermistor decreases as temperature increases. V control unit transmits front / control operation signal to / auto amp. via communication line. / auto amp. controls front automatic air conditioning system by inputting and calculating signals from each sensor and each switch. / auto amp. has self-diagnosis function. iagnosis of front automatic air conditioning system can be performed quickly. Refer to -12. The U (ocal ontrol Unit) is installed to intake door motor so as to perform the multiplex communication control (I). Refer to -18, "RT UTTI IR ITII SYST : oor ontrol". ombination meter transmits vehicle speed signal to / auto amp. via communication line. controls compressor according to status of engine and refrigerant. transmits engine coolant temperature signal to / auto amp. via communication line. ngine coolant temperature sensor measures engine coolant temperature. The sensor uses a thermistor which is sensitive to the change in temperature. The electrical resistance of the thermistor decreases as temperature increases. ront display indicates operation status of front automatic air conditioning system. ront in-vehicle sensor measures temperature of intake air that flows through aspirator to passenger room. The sensor uses a thermistor which is sensitive to the change in temperature. The electrical resistance of the thermistor decreases as temperature increases. -7

T RTS < SYST SRITI > [UTTI IR ITII] omponent escription eater & cooling unit assembly I /R agnet clutch reset switch spirator ront air mix door motor (river side) ront air mix door motor (assenger side) ront mode door motor Intake sensor Upper ventilator door motor Refer to -12. The U (ocal ontrol Unit) is installed to front air mix door motor (driver side) so as to perform the multiplex communication control (I). Refer to -18, "RT UTTI IR ITII SYST : oor ontrol". The U (ocal ontrol Unit) is installed to front air mix door motor (passenger side) so as to perform the multiplex communication control (I). Refer to -18, "RT UTTI IR ITII SYST : oor ontrol". The U (ocal ontrol Unit) is installed to front mode door motor so as to perform the multiplex communication control (I). Refer to -18, "RT UTTI IR ITII SYST : oor ontrol". Intake sensor measures temperature of front evaporator fin temperature. The sensor uses a thermistor which is sensitive to the change in temperature. The electrical resistance of the thermistor decreases as temperature increases. The U (ocal ontrol Unit) is installed to upper ventilator door motor so as to perform the multiplex communication control (I). Refer to -18, "RT UTTI IR ITII SYST : oor ontrol". / relay is integrated in I /R. I /R operates / relay when / compressor request signal is received from via communication line. The magnet clutch is the device that drives the compressor with the signal from I /R. ompressor is driven by the magnet clutch which is magnetized by electric power supply. I controls magnet clutch by turning the built in / relay to according to request. reset switch is integrated with front / control and V operation switch. ront / control operation signal is transmitted from preset switch to V control unit via communication line. Refrigerant pressure sensor Refer to -13. Sunload sensor RR UTTI IR ITII SYST Sunload sensor measures sunload amount. This sensor is a dual system so that sunload for driver side and passenger side are measured separately. This sensor converts sunload amount to voltage signal by photodiode and transmits to / auto amp.. -8

T RTS < SYST SRITI > [UTTI IR ITII] RR UTTI IR ITII SYST : omponent arts ocation II:0000000006275850 1. Rear / control 2. reset switch 3. ngine coolant temperature sensor Refer to -16, "omponent arts ocation". 4. Refer to -16, "omponent arts ocation". 7. ombination meter Refer to WI-6, "TR SYST : omponent arts ocation". 5. mbient sensor 6. V control unit Refer to V-9, "omponent arts ocation". 8. Sunload sensor 9. ront display II0813ZZ 10. Rear mode door motor 11. Rear air mix door motor 12. Rear in-vehicle sensor 13. Rear blower motor 14. Rear / solenoid valve 15. Rear / relay 16. Intake sensor 17. / auto amp.. Right side of rear / unit assembly. eft side of rear / unit assembly. ack side of engine room (R). eft side of heater & cooling unit assembly. luster lid is removed -9

T RTS < SYST SRITI > [UTTI IR ITII] RR UTTI IR ITII SYST : omponent escription II:0000000006275851 omponent escription mbient sensor V control unit / auto amp. ombination meter ngine coolant temperature sensor ront display mbient sensor measures ambient air temperature. The sensor uses a thermistor which is sensitive to the change in temperature. The electrical resistance of the thermistor decreases as temperature increases. V control unit transmits front / control operation signal to / auto amp. via communication line. / auto amp. controls rear automatic air conditioning system by inputting and calculating signals from each sensor and each switch. / auto amp. has self-diagnosis function. iagnosis of rear automatic air conditioning system can be performed quickly. ombination meter transmits vehicle speed signal to / auto amp. via communication line. transmits engine coolant temperature signal to / auto amp. via communication line. ngine coolant temperature sensor measures engine coolant temperature. The sensor uses a thermistor which is sensitive to the change in temperature. The electrical resistance of the thermistor decreases as temperature increases. ront display indicates operation status of rear automatic air conditioning system. eater & cooling unit assembly reset switch Rear / control Rear / relay Rear / unit assembly Intake sensor Rear air mix door motor Rear / solenoid valve Rear blower motor Rear in-vehicle sensor Rear mode door motor Intake sensor measures temperature of front evaporator fin temperature. The sensor uses a thermistor which is sensitive to the change in temperature. The electrical resistance of the thermistor decreases as temperature increases. reset switch is integrated with front / control and V operation switch. ront / control operation signal is transmitted from preset switch to V control unit via communication line. The operation of the rear / control is communicated with the / auto amp. via communication line. ower is supplied to the rear / solenoid valve through rear / relay with / auto amp. control. The U (ocal ontrol Unit) is installed to rear air mix door motor so as to perform the multiplex communication control (I). Refer to -26, "RR UTTI IR ITII SYST : oor ontrol". Rear / solenoid valve operates by power supply from rear / relay and opens refrigerant line to rear evaporator. Refer to -13. Rear in-vehicle sensor measures temperature of intake air that flows through rear blower motor to passenger room. The sensor uses a thermistor which is sensitive to the change in temperature. The electrical resistance of the thermistor decreases as temperature increases. The U (ocal ontrol Unit) is installed to rear mode door motor so as to perform the multiplex communication control (I). Refer to -26, "RR UTTI IR ITII SYST : oor ontrol". Sunload sensor S (V IT TR SYST) Sunload sensor measures sunload amount. This sensor is a dual system so that sunload for driver side and passenger side are measured separately. This sensor converts sunload amount to voltage signal by photodiode and transmits to / auto amp.. -10

T RTS < SYST SRITI > [UTTI IR ITII] S (V IT TR SYST) : omponent arts ocation II:0000000006275852 1. reset switch 2. xhaust gas / outside odor detecting sensor 3. V control unit Refer to V-9, "omponent arts ocation". 4. ront display 5. Ionizer 6. Intake door motor 7. / auto amp.. eft side of heater & cooling unit assembly. ack side of blower unit assembly. luster lid is removed II0814ZZ S (V IT TR SYST) : omponent escription II:0000000006275853 omponent lower unit Intake door motor V control unit / auto amp. xhaust gas / outside odor detecting sensor escription The U (ocal ontrol Unit) is installed to intake door motor so as to perform the multiplex communication control (I). Refer to -18, "RT UTTI IR ITII SYST : oor ontrol". V control unit transmits / switch operation signal to / auto amp. via communication line. / auto amp. controls S (advanced climate control system) by inputting and calculating signals from each sensor and each switch. / auto amp. has self-diagnosis function. iagnosis of S (advanced climate control system) can be performed quickly. xhaust gas / outside odor detecting sensor measures unpleasant odor outside of passenger room. In addition to previous exhaust gas detection function, unpleasant odor in ambient atmosphere is measured. -11

T RTS < SYST SRITI > [UTTI IR ITII] ront display eater & cooling unit assembly reset switch spirator omponent Ionizer escription ront display indicates operation status of S (advanced climate control system). Ionizer generates an approximately equal proportional amount of positive and negative ions in the air. reset switch is integrated with front / control and V operation switch. ront / control operation signal is transmitted from preset switch to V control unit via communication line. II:0000000006275856 The aspirator generates the vacuum by the air blown from the heater & cooling unit and draws the air of the passenger room to the front in-vehicle sensor area via the aspirator duct. ront lower otor RI1804 II:0000000006275857 The front blower motor utilizes a brush-less motor with a rotating magnet. Quietness is improved comparing to a conventional motor (brush motor) that rotates coil while brush functions as contact points. RI2467 Z152-12

T RTS < SYST SRITI > [UTTI IR ITII] Rear lower otor The rear blower motor utilizes a brush-less motor with a rotating magnet. Quietness is improved comparing to a conventional motor (brush motor) that rotates coil while brush functions as contact points. II:0000000006275858 RI2467 Refrigerant ressure Sensor II:0000000006275859 escription Refrigerant pressure sensor is installed to upper portion of liquid tank. The refrigerant pressure sensor converts high-pressure side refrigerant pressure into voltage and outputs it to. operates cooling system protection and idle speed control according to voltage value that is input. Z152 I2657 Structure and operation The refrigerant pressure sensor is a capacitance type sensor. It consists of a pressure detection area and a signal processing area. The pressure detection area, which is a variable capacity condenser, changes internal static capacitance according to pressure force. The signal processing area detects the static capacitance of the pressure detection area, converts the static capacitance into a voltage value, and transmits the voltage value to. -13

SYST < SYST SRITI > [UTTI IR ITII] SYST RT UTTI IR ITII SYST RT UTTI IR ITII SYST : System iagram II:0000000006275860 II0816 RT UTTI IR ITII SYST : System escription II:0000000006275861 ront automatic air conditioning system is controlled by each function of / auto amp., and I / R. ontrol by / auto amp. - -15, "RT UTTI IR ITII SYST : ir low ontrol" - -16, "RT UTTI IR ITII SYST : ir Inlet ontrol" -14

SYST < SYST SRITI > [UTTI IR ITII] - -17, "RT UTTI IR ITII SYST : ir utlet ontrol" - -17, "RT UTTI IR ITII SYST : ompressor ontrol" - -18, "RT UTTI IR ITII SYST : oor ontrol" - -21, "RT UTTI IR ITII SYST : Temperature ontrol" - orrection for input value of each sensor mbient sensor (setting temperature correction) / auto amp. controls passenger room temperature so that the optimum level always matches the temperature level that passenger may feel. orrection is applied to the target temperature that is set using temperature control dial, according to ambient temperature detected by ambient sensor. ront in-vehicle sensor [in-vehicle temperature (front side) correction] assenger room temperature (front side) detected by front in-vehicle sensor is corrected for each front air conditioning control (driver side and passenger side) Intake sensor (intake temperature correction) / auto amp. performs correction to change recognition intake temperature of / auto amp. quickly when difference is large between recognition intake temperature and intake temperature detected by intake temperature sensor. The correction is performed to change recognition intake temperature slowly when difference is small. Sunload sensor (sunload amount correction) Sunload amount detected by sunload sensor is corrected for each air conditioning control (driver side and passenger side). / auto amp. performs correction to change recognition sunload amount of / auto amp. slowly when sunload amount changes quickly, for example when entering or exiting a tunnel. ontrol by - ooling fan control Refer to -41, "I TR : System escription". - ir conditioning cut control. Refer to -47, "IR ITII UT TR : System escription". ontrol by I /R - Relay control Refer to S-5, "RY TR SYST : System escription". - ooling fan control Refer to S-8, "WR TR SYST : System escription". ront / control (preset switch) transmits the commands for front automatic air conditioning system operation to V control unit via communication line, then V control unit transmits the commands to / auto amp. via communication. / auto amp. transmits each indication information to V control unit via communication. V control unit displays each indication information that is received. RT UTTI IR ITII SYST : ir low ontrol II:0000000006275862 SRITI / auto amp. changes duty ratio of blower motor drive signal and controls air flow continuously. When air flow is increased, duty ratio of front blower motor control signal gradually increases to prevent a sudden increase in air flow. In addition to manual control and automatic control, air flow control is consist of starting fan speed control, low coolant temperature starting control, high in-vehicle temperature starting control and fan speed control at door motor operation UTTI IR W TR / auto amp. decides target air flow depending on target front air mix door opening angle. / auto amp. changes duty ratio of front blower motor control signal and controls the air flow continuously so that air flow matches to target air flow. -15

SYST < SYST SRITI > [UTTI IR ITII] When air outlet is VT or /, the minimum air flow is changed depending on sunload. STRTI IR W TR When front blower motor is activated, / auto amp. gradually increases duty ratio of front blower motor control signal to prevent a sudden increase in discharge air flow. It takes approximately 8 seconds for air flow to reach I from W. II0735 W T TRTUR STRTI TR If the engine coolant temperature is 56 (133 ) or less, to prevent a cold discharged air flow, / auto amp. suspends front blower motor activation for the maximum 150 seconds depending on target front air mix door opening angle. fter this, front blower motor control signal is increased gradually, and front blower motor is activated. II0736 I I-VI TRTUR STRTI TR When front evaporator fin temperature is high [intake sensor value is 35 (95 ) or more], to prevent a hot discharged air flow, / auto amp. suspends front blower motor activation for approximately 3 seconds so that front evaporator is cooled by refrigerant. S TR T R TR RTI When front mode door motor is activated while air flow is more than the specified value, / auto amp. reduces temporarily fan speed wo that front mode door moves smoothly. RT UTTI IR ITII SYST : ir Inlet ontrol II:0000000006275863 The intake door is automatically controlled by the temperature setting, ambient temperature, in-vehicle temperature (front side), intake temperature, amount of sunload and / operation of the compressor. Intake door automatic control selects R, 20% R, or R depending on a target front air mix door opening angle, based on invehicle temperature (front side), ambient temperature, and sunload. II0737 II0732-16

SYST < SYST SRITI > [UTTI IR ITII] RT UTTI IR ITII SYST : ir utlet ontrol While air outlet is in automatic control, / auto amp. selects the front mode door position depending on a target front air mix door angle and outlet air temperature calculated from sunload. If ambient temperature is excessively low, / is selected to prevent windshield fogging when air outlet is set to T. II:0000000006275864 RT UTTI IR ITII SYST : ompressor ontrol II0730 II:0000000006275865 SRITI When the compressor activation condition is satisfied while blower motor is activated, / auto amp. transmits / signal and blower fan signal to via communication. judges that the compressor can be activated depending on each sensors state (refrigerant pressure sensor signal, and others). nd transmits / compressor request signal to I /R via communication. I /R turns / relay and activates the compressor depending on request from. RSSR RTTI TR T RSSUR UTI When high-pressure side value that is detected by refrigerant pressure sensor is as per the following state, requests I /R to turn / relay and stops the compressor. 3.12 a (31.82 kg/cm 2, 452.4 psi) or more (When the engine speed is less than 1,500 rpm) 2.74 a (27.95 kg/cm 2, 397.3 psi) or more (When the engine speed is 1,500 rpm or more) 0.14 a (1.43 kg/cm 2, 20.3 psi) or less RSSR I IRUTI TR When the engine starts while the engine coolant temperature is 56 (133 ) or less, activates the compressor for approximately 6 seconds and circulates the compressor lubricant once. W TRTUR RTTI TR When intake sensor detects that front evaporator fin temperature is 2.5 (37 ) or less, / auto amp. requests to turn compressor, and stops the compressor. When the front evaporator fin temperature returns to 5.0 (41 ) or more, the compressor is activated. II0742 RTI RT TR When set temperature is other than fully cold or air outlet is VT, / or T / auto amp. controls the compressor activation depending on ambient temperature. IR ITII UT TR When set engine is running is excessively high load condition, requests I /R to turn / relay, and stops the compressor. Refer to -47, "IR ITII UT TR : System escription" for details. -17

SYST < SYST SRITI > [UTTI IR ITII] RT UTTI IR ITII SYST : oor ontrol II:0000000006275866 R TR TR U (ocal ontrol Unit) is built in to each door motor. nd detects door position by R (otentio alance Resistor). / auto amp. communicates with each U via communication line. nd receives each door position feed back signal from each U. ach U controls each door to the appropriate position depending on the control signal from / auto amp. when the door movement is complete, transmits the signal of door movement completion to / auto amp. SWITS TIR TR UTI With S (dvanced limate ontrol System) II0817 II0727ZZ -18

SYST < SYST SRITI > [UTTI IR ITII] 1. Intake door 2. In-cabin microfilter 3. lower motor 4. vaporator 5. ir mix door (river side/assenger 6. eater core side) 7. oot door 8. Ventilator door 9. Upper ventilator door 10. efroster door resh air intake Recirculation air enter ventilator Side ventilator Upper ventilator oot Rear foot efroster Switch/ial position Ventilator door oot door efroster door oor position Intake door Upper ventilator door ir mix door (river side) UT switch UT UT ir mix door (assenger side) switch VT / I T / switch * R Intake switch R Upper ventilator switch Temperature control dial (river side) Temperature control dial (river side) Temperature control dial (assenger side) U switch: U switch: *: Inlet status is displayed by indicator when activating automatic control Without S (dvanced limate ontrol System) 18.0 (60 ) 18.5 (61 ) 31.5 (89 ) UT 32.0 (90 ) 18.0 (60 ) 18.5 (61 ) 31.5 (89 ) UT 32.0 (90 ) 18.0 (60 ) 18.5 (61 ) 31.5 (89 ) UT 32.0 (90 ) switch UT -19

SYST < SYST SRITI > [UTTI IR ITII] II0727ZZ 1. Intake door 2. In-cabin microfilter 3. lower motor 4. vaporator 5. ir mix door (river side/assenger 6. eater core side) 7. oot door 8. Ventilator door 9. Upper ventilator door 10. efroster door resh air intake Recirculation air enter ventilator Side ventilator Upper ventilator oot Rear foot efroster oor position Switch/ial position Ventilator door oot door efroster door Intake door Upper ventilator door ir mix door (river side) ir mix door (assenger side) UT switch UT UT VT switch / I T / switch R switch * R switch * Upper ventilator switch -20

SYST < SYST SRITI > [UTTI IR ITII] Temperature control dial (river side) Temperature control dial (river side) Temperature control dial (assenger side) Switch/ial position U switch: U switch: *: Inlet status is displayed by indicator when activating automatic control IR ISTRIUTI 18.0 (60 ) 18.5 (61 ) 31.5 (89 ) UT 32.0 (90 ) 18.0 (60 ) 18.5 (61 ) 31.5 (89 ) UT 32.0 (90 ) 18.0 (60 ) 18.5 (61 ) 31.5 (89 ) Ventilator door oot door efroster door oor position Intake door Upper ventilator door ir mix door (river side) UT 32.0 (90 ) switch UT ir mix door (assenger side) ischarge air flow ode position ondition ir outlet/distribution VT T enter Side ront Rear 50% 50% U and Upper ventilator switch: 30% 30% 26% 14% 14% 36% 23% 27% 12% 32% 20% 36% RT UTTI IR ITII SYST : Temperature ontrol When ignition switch is in the position, / auto amp. always automatically controls temperature regardless of front air conditioning operational state. / auto amp. calculates the target front air mix door opening angle depending on set temperature, in-vehicle temperature (front side), ambient temperature, and sunload. ront air mix door is controlled depending on the comparison of current front air mix door opening angle and target front air mix door opening angle. Regardless of in-vehicle temperature (front side), ambient temperature, and sunload, front air mix door is fixed at the fully cold position when set temperature is 18.0 (60 ), and at the fully hot position when set temperature is 32.0 (90 ). 11% 89% RT UTTI IR ITII SYST : ail-safe II:0000000006275867 II0731 II:0000000006275868 I-S UTI -21

SYST < SYST SRITI > [UTTI IR ITII] If a communication error exists between the / auto amp., and the V control unit and preset switch for 30 seconds or longer, air conditioning is controlled under the following conditions: When ambient temperature is less than 3 (37 ) and engine coolant temperature is less than 56 (133 ) ompressor ir outlet ir inlet lower fan speed Set temperature : : : R (resh air intake) : UT : Setting before communication error occurs When ambient temperature is 3 (37 ) or more, or engine coolant temperature is 56 (133 ) or more ompressor ir outlet ir inlet lower fan speed Set temperature : : UT : 20% R (20% fresh air intake) : UT : Setting before communication error occurs RR UTTI IR ITII SYST -22

SYST < SYST SRITI > [UTTI IR ITII] RR UTTI IR ITII SYST : System iagram II:0000000006275869 II0818 RR UTTI IR ITII SYST : System escription II:0000000006275870 Rear automatic air conditioning system is controlled by each function of / auto amp.. ontrol by / auto amp. - -24, "RR UTTI IR ITII SYST : ir low ontrol" - -25, "RR UTTI IR ITII SYST : ir utlet ontrol" - -26, "RR UTTI IR ITII SYST : oor ontrol" - -27, "RR UTTI IR ITII SYST : Temperature ontrol" - orrection for input value of each sensor mbient sensor (setting temperature correction) -23

SYST < SYST SRITI > [UTTI IR ITII] / auto amp. controls passenger room temperature so that the optimum level always matches the temperature level that passenger may feel. orrection is applied to the target temperature that is set using temperature control dial, according to ambient temperature detected by ambient sensor. Rear in-vehicle sensor [in-vehicle temperature (rear side) correction] assenger room temperature (rear side) detected by rear in-vehicle sensor is corrected for each rear automatic air conditioning control. Intake sensor (intake temperature correction) / auto amp. performs correction to change recognition intake temperature of / auto amp. quickly when difference is large between recognition intake temperature and intake temperature detected by intake temperature sensor. The correction is performed to change recognition intake temperature slowly when difference is small. Sunload sensor (sunload amount correction) Sunload amount detected by sunload sensor is corrected for each rear automatic air conditioning control. / auto amp. performs correction to change recognition sunload amount of / auto amp. slowly when sunload amount changes quickly, for example when entering or exiting a tunnel. ront control peration by front controller - ront / control (preset switch) transmits the commands for rear automatic air conditioning system operation to V control unit via communication line, then V control unit transmits the commands to / auto amp. via communication. / auto amp. transmits each indication information to V control unit via communication. V control unit displays each indication information that is received. peration by rear controller - Rear / control transmits the commands for rear automatic air conditioning system operation to / auto amp. via communication line. RR UTTI IR ITII SYST : ir low ontrol II:0000000006275871 SRITI / auto amp. changes duty ratio of blower motor drive signal and controls air flow continuously. When air flow is increased, duty ratio of rear blower motor control signal gradually increases to prevent a sudden increase in air flow. In addition to manual control and automatic control, air flow control is compose of starting fan speed control, low coolant temperature starting control, high in-vehicle temperature starting control and fan speed control at door motor operation UTTI IR W TR / auto amp. decides target air flow depending on target rear air mix door opening angle. / auto amp. changes duty ratio of rear blower motor control signal and controls the air flow continuously so that air flow matches to target air flow. When air outlet is VT or /, the minimum air flow is changed depending on sunload. STRTI IR W TR II0738-24

SYST < SYST SRITI > [UTTI IR ITII] When rear blower motor is activated, / auto amp. gradually increases duty ratio of rear blower motor control signal to prevent a sudden increase in discharge air flow. It takes approximately 8 seconds for air flow to reach I from W. W T TRTUR STRTI TR If the engine coolant temperature is 56 (133 ) or less, to prevent a cold discharged air flow, / auto amp. suspends rear blower motor activation for the maximum 150 seconds depending on target rear air mix door opening angle. fter this, rear blower motor control signal is increased gradually, and rear blower motor is activated. II0739 I I-VI TRTUR STRTI TR When front evaporator fin temperature is high [intake sensor value is 35 (95 ) or more], to prevent a hot discharged air flow, / auto amp. suspends rear blower motor activation for approximately 3 seconds so that rear evaporator is cooled by refrigerant. S TR T R TR RTI When rear mode door motor is activated while air flow is more than the specified value, / auto amp. reduces temporarily fan speed wo that rear mode door moves smoothly. RR UTTI IR ITII SYST : ir utlet ontrol II:0000000006275872 While air outlet is in automatic control, / auto amp. selects the rear mode door position depending on a target rear air mix door angle and outlet air temperature calculated from sunload. II0740 II0733-25

SYST < SYST SRITI > [UTTI IR ITII] RR UTTI IR ITII SYST : oor ontrol II:0000000006275873 R TR TR U (ocal ontrol Unit) is built in to each door motor. nd detects door position by R (otentio alance Resistor). / auto amp. communicates with each U via communication line. nd receives each door position feed back signal from each U. ach U controls each door to the appropriate position depending on the control signal from / auto amp. when the door movement is complete, transmits the signal of door movement completion to / auto amp. SWITS TIR TR UTI II0729 II0744ZZ 1. Rear blower motor 2. Rear evaporator 3. Rear air mix door 4. Rear heater core 5. Rear mode door Recirculation air Rear ventilator Rear / foot UT switch Switch/ial position ront / control Rear / control oor position Rear mode door Rear air mix door UT -26

SYST < SYST SRITI > [UTTI IR ITII] switch oor position Switch/ial position Rear mode door Rear air mix door VT / T Temperature control dial (front / control) Temperature control switch (rear / control) IR ISTRIUTI 18.0 (60 ) 18.5 (61 ) 31.5 (89 ) UT 32.0 (90 ) switch UT ode position ischarge air flow ir outlet/distribution VT T 100% 62% 38% 100% RR UTTI IR ITII SYST : Temperature ontrol II:0000000006275874 When ignition switch is in the position, / auto amp. always automatically controls temperature regardless of rear air conditioning operational state. / auto amp. calculates the target rear air mix door opening angle depending on set temperature, in-vehicle temperature (rear side), ambient temperature, and sunload. Rear air mix door is controlled depending on the comparison of current rear air mix door opening angle and target front air mix door opening angle. Regardless of in-vehicle temperature (rear side), ambient temperature, and sunload, rear air mix door is fixed at the fully cold position when set temperature is 18.0 (60 ), and at the fully hot position when set temperature is 32.0 (90 ). S (V IT TR SYST) II0734-27

SYST < SYST SRITI > [UTTI IR ITII] S (V IT TR SYST) : System iagram II:0000000006275875 II0819 S (V IT TR SYST) : System escription II:0000000006275876 S (advanced climate control system) controls passenger room air. It maintains the cleanliness of the passenger room air using an in-cabin microfilter and a combination of each of the following functions. - -28, "S (V IT TR SYST) : utomatic Intake ontrol (xhaust as / utside dor etecting echanism)" - -29, "S (V IT TR SYST) : lasmacluster ontrol" T: lasmacluster ion technology developed by Sharp orporation is installed in this item. lasmacluster is a trademark of Sharp orporation. Various operations of S (advanced climate control system) are transmitted from preset switch to V control unit via communication line and from V control unit to / auto amp. via communication. / auto amp. sends each indication information to V control unit via communication. V control unit displays each indication information that is received. S (V IT TR SYST) : utomatic Intake ontrol (xhaust as / utside dor etecting echanism) II:0000000006275877 SRITI In addition to air inlet automatic control of front automatic air conditioning system, / auto amp. controls automatically air inlet according to signal from exhaust gas / outside odor detecting sensor, so that unpleasant outside odor does not enter in passenger room. RTI SRITI When pressing auto intake switch while front blower motor is operated and switch is, auto intake switch indicator lamp and intake switch indicator lamp turn. ir inlet is fixed to recirculation for approximately 5 minutes, and then is switched to automatic intake control (exhaust gas / outside odor detecting mechanism). ir inlet switches to recirculation when exhaust gas or outside odor is detected while automatic intake control (exhaust gas / outside odor detecting mechanism) is operated. fter that, air inlet switches to fresh air intake when exhaust gas or outside odor becomes not detectable. T: -28

SYST < SYST SRITI > [UTTI IR ITII] Sensitivity of exhaust gas / outside odor detecting sensor can be changed by S SSR UST- T in WR SURT mode of SUT-III. Refer to -70, "S (V IT TR SYST) : xhaust as / utside dor etecting Sensor Sensitivity djustment unction". utomatic intake control (exhaust gas / outside odor detecting mechanism) does not operate when ambient temperature is 2 (28 ) or less. In this case, control is only for control of automatic air inlet of automatic air conditioning system. S (V IT TR SYST) : lasmacluster ontrol SRITI II:0000000006275878 lasmacluster control eliminates microbes and reduces odor on interior surface by including high density lasmacluster ion in air conditioning outlet air flow. RTI SRITI lasmacluster control operates by interlocking to blower motor. lasmacluster control operates when blower motor operates. ontrol status is displayed on front air conditioning system display screen. Refer to -37, "S (V IT TR SYST) : Switch ame and unction". T: lasmacluster ion technology developed by Sharp orporation is installed in this item. lasmacluster is a trademark of Sharp orporation. -29

RTI < SYST SRITI > [UTTI IR ITII] RTI RT UTTI IR ITII SYST RT UTTI IR ITII SYST : Switch ame and unction WIT S (V IT TR SYST) II:0000000006275881 / isplay ront air conditioning system state is indicated on the display. When STTUS on multifunction switch is pressed while front air conditioning system is in the position, the display changes to state indication display of front air conditioning system. When front air conditioning system is operated while navigation system or audio system is displayed, front air conditioning system state is indicated in the lower portion of display for several seconds. When switch is pressed while front air conditioning system is in the position, state indication display is indicated for several seconds. isplay Screen ontroller (reset Switch) II0821 II0823ZZ 1. UT switch 2. Temperature control dial (river side) Switch peration 3. switch 4. switch 5. / switch 6. Upper ventilator switch 7. Temperature control dial (passenger 8. U switch 9. Intake switch side) 10. an switch 11. switch -30

RTI < SYST SRITI > [UTTI IR ITII] UT switch / switch efroster () switch U switch an switch (U/W) switch switch Turns the switch indicator lamp and "UT" indicator on the display, and then front air conditioning system becomes the following state. ir inlet: utomatic control ir outlet: utomatic control lower fan: utomatic control ompressor: Turns the compressor control (switch indicator) between each time while front blower fan is activated. T: When front blower fan is, the compressor control cannot be activated. When the compressor control (switch indicator) is in the position, air inlet is fresh air intake (R). Turns mode (switch indicator) between each time. When switch is pressed while front air conditioning system is in the position. When mode is turned, front air conditioning system becomes the following state. - ir inlet: resh air intake - ir outlet: - lower fan: utomatic control (If fan speed other than UT is selected before pressing switch, fan speed is manual control.) - ompressor: When mode is turned, front air conditioning system state returns to the previous state before mode is selected. ut, the following state is continued. - ir inlet: resh air intake - ompressor: When switch is pressed while front air conditioning system is in the position. When mode is turned, front air conditioning system becomes the following state. - ir inlet: resh air intake - ir outlet: - lower fan: utomatic control - ompressor: When mode is turned, entire front air conditioning system is set to auto mode. T: When mode turns while front air conditioning system is in automatic control ( UT is indicated), automatic control is released ( UT turns ). Turns left and right ventilation temperature separately control (switch indicator) between each time. When U switch indicator is, the driver side and passenger side temperatures can each be set independently. When U switch indicator is, the driver side outlet and setting temperature is applied to both sides. eft and right ventilation temperature separately control is cancelled by turning the mode. T: When front air conditioning system is in the position, left and right ventilation temperature separately control can be selected only while front air conditioning system state (when switch is pressed) is indicated on the display. lower fan speed is manually controlled with these switches. Seven speeds are available for manual control (as shown on the display screen) T: When fan switch is pressed while front air conditioning system is in, front air conditioning system is activated. (ompressor control state returns to the previous state before front air conditioning system.) When fan switch is pressed while front air conditioning system is in automatic control ( UT is indicated), automatic control is released ( UT turns ). Selects air outlet sequentially from VT / T / VT each time. T: When front air conditioning system is in the position, air outlet can be selected. When switch is pressed while front air conditioning system is in automatic control ( UT is indicated), automatic control is released ( UT turns ). Turns front air conditioning system. When front air conditioning system turns, air inlet and air outlet become the automatic control. -31

RTI < SYST SRITI > [UTTI IR ITII] Intake switch Temperature control dial (driver side) Temperature control dial (passenger side) Upper ventilator switch ir inlet changes between recirculation (R) fresh air intake (R) each time this switch is pressed. Intake switch indicator : Recirculation Intake switch indicator : resh air intake T: When front air conditioning system is in the position, air inlet can be selected. When switch and switch is in the / or position, air inlet cannot be selected to recirculation (R). Selects set temperature within a range between 18.0 (60 ) 32.0 (90 ) at a rate of 0.5 (1.0 ) each time the dial is rotated. - lockwise rotation: Set temperature increases. - ounterclockwise rotation: Set temperature decreases. T: When front air conditioning system is in the position, set temperature can be selected only while front air conditioning system state (when switch is pressed) is indicated on the display. Selects set temperature within a range between 18.0 (60 ) 32.0 (90 ) at a rate of 0.5 (1.0 ) each time the dial is rotated. - lockwise rotation: Set temperature increases. - ounterclockwise rotation: Set temperature decreases. When the temperature control dial is turned, U switch indicator turns. T: When front air conditioning system is in the position, set temperature can be selected only while front air conditioning system state (when switch is pressed) is indicated on the display. Turns the upper ventilator control (switch indicator) between each time while front blower fan is activated. T: When front air conditioning system is in the position and air outlet is position, upper ventilator control cannot be activated. When front air conditioning system is in the position, upper ventilator control can be selected only while front air conditioning system state (when switch is pressed) is indicated on the display. WITUT S (V IT TR SYST) / isplay ront air conditioning system state is indicated on the display. When STTUS on multifunction switch is pressed while front air conditioning system is in the position, the display changes to state indication display of front air conditioning system. When front air conditioning system is operated while navigation system or audio system is displayed, front air conditioning system state is indicated in the lower portion of display for several seconds. When switch is pressed while front air conditioning system is in the position, state indication display is indicated for several seconds. isplay Screen ontroller (reset Switch) II0719-32

RTI < SYST SRITI > [UTTI IR ITII] II0822ZZ 1. UT switch 2. Temperature control dial (river side) Switch peration 3. switch 4. switch 5. / switch 6. Upper ventilator switch 7. Temperature control dial (passenger 8. U switch 9. R switch side) 10. R switch 11. an switch 12. switch UT switch / switch efroster () switch Turns the switch indicator lamp and "UT" indicator on the display, and then front air conditioning system becomes the following state. ir inlet: utomatic control ir outlet: utomatic control lower fan: utomatic control ompressor: Turns the compressor control (switch indicator) between each time while front blower fan is activated. T: When front blower fan is, the compressor control cannot be activated. When the compressor control (switch indicator) is in the position, air inlet is fresh air intake (R). Turns mode (switch indicator) between each time. When switch is pressed while front air conditioning system is in the position. When mode is turned, front air conditioning system becomes the following state. - ir inlet: resh air intake - ir outlet: - lower fan: utomatic control (If fan speed other than UT is selected before pressing switch, fan speed is manual control.) - ompressor: When mode is turned, front air conditioning system state returns to the previous state before mode is selected. ut, the following state is continued. - ir inlet: resh air intake - ompressor: When switch is pressed while front air conditioning system is in the position. When mode is turned, front air conditioning system becomes the following state. - ir inlet: resh air intake - ir outlet: - lower fan: utomatic control - ompressor: When mode is turned, entire front air conditioning system is set to auto mode. T: When mode turns while front air conditioning system is in automatic control ( UT is indicated), automatic control is released ( UT turns ). -33

RTI < SYST SRITI > [UTTI IR ITII] U switch an switch (U/W) R switch switch switch R switch Temperature control dial (driver side) Turns left and right ventilation temperature separately control (switch indicator) between each time. When U switch indicator is, the driver side and passenger side temperatures can each be set independently. When U switch indicator is, the driver side outlet and setting temperature is applied to both sides. eft and right ventilation temperature separately control is cancelled by turning the mode. T: When front air conditioning system is in the position, left and right ventilation temperature separately control can be selected only while front air conditioning system state (when switch is pressed) is indicated on the display. lower fan speed is manually controlled with these switches. Seven speeds are available for manual control (as shown on the display screen) T: When fan switch is pressed while front air conditioning system is in, front air conditioning system is activated. (ompressor control state returns to the previous state before front air conditioning system.) When fan switch is pressed while front air conditioning system is in automatic control ( UT is indicated), automatic control is released ( UT turns ). ir inlet is selected to fresh air intake (R) by pressing this switch. - R indicator: - R indicator: When R indicator is, pressing the R switch for approximately 1.5 seconds or more, and then the R and R switch indicators blink twice and the system is switched to the automatic control. T: When front air conditioning system is in the position, air inlet can be selected. Selects air outlet sequentially from VT / T / VT each time. T: When front air conditioning system is in the position, air outlet can be selected. When switch is pressed while front air conditioning system is in automatic control ( UT is indicated), automatic control is released ( UT turns ). Turns front air conditioning system. When front air conditioning system turns, air inlet and air outlet become the automatic control. ir inlet is selected to fresh air intake (R) by pressing this switch. - R indicator: - R indicator: When R indicator is, pressing the R switch for approximately 1.5 seconds or more, and then the R and R switch indicators blink twice and the system is switched to the automatic control. T: When front air conditioning system is in the position, air inlet can be selected. When switch and switch is in the / or position, air inlet cannot be selected to recirculation (R). Selects set temperature within a range between 18.0 (60 ) 32.0 (90 ) at a rate of 0.5 (1.0 ) each time the dial is rotated. - lockwise rotation: Set temperature increases. - ounterclockwise rotation: Set temperature decreases. T: When front air conditioning system is in the position, set temperature can be selected only while front air conditioning system state (when switch is pressed) is indicated on the display. -34

RTI < SYST SRITI > [UTTI IR ITII] Temperature control dial (passenger side) Upper ventilator switch RR UTTI IR ITII SYST RR UTTI IR ITII SYST : Switch ame and unction RT TR RTI Selects set temperature within a range between 18.0 (60 ) 32.0 (90 ) at a rate of 0.5 (1.0 ) each time the dial is rotated. - lockwise rotation: Set temperature increases. - ounterclockwise rotation: Set temperature decreases. When the temperature control dial is turned, U switch indicator turns. T: When front air conditioning system is in the position, set temperature can be selected only while front air conditioning system state (when switch is pressed) is indicated on the display. Turns the upper ventilator control (switch indicator) between each time while front blower fan is activated. T: When front air conditioning system is in the position and air outlet is position, upper ventilator control cannot be activated. When front air conditioning system is in the position, upper ventilator control can be selected only while front air conditioning system state (when switch is pressed) is indicated on the display. II:0000000006275882 / isplay Rear air conditioning system state is indicated on the front display. When RR switch is pressed while air conditioning system is in the position, the front display changes to state indication display (rear control mode) of rear air conditioning system. isplay screen II0720ZZ ontroller (reset Switch) With S (advanced climate control system) II0825ZZ 1. UT switch 2. Temperature control dial (river 3. switch side) 4. RR switch 5. switch 6. an switch -35

RTI < SYST SRITI > [UTTI IR ITII] Without S (advanced climate control system) II0824ZZ 1. UT switch 2. Temperature control dial (river side) 3. switch 4. RR switch 5. switch 6. an switch Switch peration UT switch an switch (U/W) switch switch RR switch Temperature control dial (driver side) Turns the switch indicator lamp and "UT" indicator on the front display, and then rear air conditioning system becomes the following state. ir outlet: utomatic control lower fan: utomatic control ompressor: lower fan speed is manually controlled with these switches. Seven speeds are available for manual control (as shown on the display screen) T: When fan switch is pressed while air conditioning system is in automatic control ( UT is indicated), automatic control is released ( UT turns ). Selects air outlet sequentially from VT / T VT each time. T: When switch is pressed while air conditioning system is in automatic control ( UT is indicated), automatic control is released ( UT turns ). Turns rear air conditioning system. (When rear control mode is ) When rear air conditioning system turns, air outlet become the automatic control. Turns the switch indicator lamp and rear control mode on the front display, and then rear air conditioning system becomes the following state. - ir outlet: utomatic control - lower fan: utomatic control - ompressor: Rear control mode is released when switch is pressed again (rear air conditioning system operates continuously). Selects set temperature within a range between 18.0 (60 ) 32.0 (90 ) at a rate of 0.5 (1.0 ) each time the dial is rotated. - lockwise rotation: Set temperature increases. - ounterclockwise rotation: Set temperature decreases. RR TRR RTI ontroller (Rear / ontrol) -36

RTI < SYST SRITI > [UTTI IR ITII] 1. switch 2. an switch 3. isplay 4. Temperature control switch 5. switch 6. UT switch Switch peration II0718ZZ UT switch an switch (U/W) switch switch Temperature control switch S (V IT TR SYST) S (V IT TR SYST) : Switch ame and unction RTI ISY lasmacluster ion display Turns the switch indicator lamp and "UT" indicator on the display, and then rear air conditioning system becomes the following state. ir outlet: utomatic control lower fan: utomatic control ompressor: lower fan speed is manually controlled with these switches. Seven speeds are available for manual control (as shown on the display screen) T: When fan switch is pressed while air conditioning system is in automatic control ( UT is indicated), automatic control is released ( UT turns ). Selects air outlet sequentially from VT / T VT each time. T: When switch is pressed while air conditioning system is in automatic control ( UT is indicated), automatic control is released ( UT turns ). Turns rear air conditioning system. When rear air conditioning system turns, air outlet become the automatic control. Setting temperature is selected using this switch with in a range between 18.0 (60 ) 32.0 (90 ) at a rate of 0.5 (1.0 ) per adjustment. : ress: Set temperature increases. : ress: Set temperature decreases. lasmacluster control state is indicated on the front display. lasmacluster ion display is switched as shown in the figure depending on air flow. T: lasmacluster ion technology developed by Sharp orporation is installed in this item. lasmacluster is a trademark of Sharp orporation. II:0000000006275883-37

RTI < SYST SRITI > [UTTI IR ITII] - When air flow is small II0410ZZ - When air flow is large ontroller (reset Switch) II0411ZZ II0826ZZ 1. uto intake switch Switch name uto intake switch unction utomatic intake control (exhaust gas / outside odor detecting mechanism) mode (switch indicator) changes between each time when auto intake switch is pressed while front blower motor is activated. When auto intake switch turns, front air conditioning system becomes the following status. - / switch: - ir inlet: Recirculation [fter approximately 5 minutes, air inlet is switched to automatic intake control (exhaust gas / outside odor detecting mechanism).] When auto intake switch turns, air inlet becomes the fresh air intake. T: Interlocking condition of / switch can be changed. Refer to -70, "S (V I- T TR SYST) : uto Intake Switch Interlocking ovement hange unction". uto intake switch does not turn during the following status. - ir outlet: - mbient temperature: 2 (28 ) or less -38

ISIS SYST (V) < SYST SRITI > [UTTI IR ITII] ISIS SYST (V) escription II:0000000006275884 ir conditioning system performs self-diagnosis, operation check, function diagnosis, and various settings using diagnosis function of each control unit. U iagnostic item (SUT-III) Self iagnostic Result / auto amp. V ata onitor ctive Test V control unit Work support UTI V Self iagnostic Result ulti V system on board diagnosis function I Self iagnostic Result ata onitor I /R I /R Self iagnostic Result ata onitor uto active test SUT-III unction II:0000000006275885 SUT-III performs the following functions via communication with / auto amp. iagnostic mode Self diagnostic result ata monitor ctive test Work support U identification T: iagnosis should be performed with engine running. oor motor operation speeds become slower and results may be returned even for normal operation if battery voltage drops below 12 V during self-diagnosis. S-ISIS RSUTS Refer to -45, "T Index". T ITR isplay item list onitor item [Unit] T S I-V T [ ( )] [ ( )] escription isplays the diagnosis results judged by / auto amp. isplays the input/output signal of / auto amp. The signals used to activate each device are forcibly supplied from / auto amp. hanges the setting for each setting function. isplays the part number of / auto amp. escription mbient sensor value converted from ambient sensor signal received from ambient sensor ront in-vehicle sensor value converted from front in-vehicle sensor signal received from front in-vehicle sensor IT T S [ ( )] Intake sensor value converted from intake sensor signal received from intake sensor SU S [w/m 2 ] Sunload sensor value converted from sunload sensor signal (driver side) received from sunload sensor S [ ( )] mbient temperature value calculated by / auto amp. I-V [ ( )] In-vehicle temperature (front side) value calculated by / auto amp. IT T [ ( )] ront evaporator fin temperature value calculated by / auto amp. SU S [w/m 2 ] Sunload value (driver side) calculated by / auto amp. -39

ISIS SYST (V) < SYST SRITI > [UTTI IR ITII] RQ SI [n/ff] isplays / switch / status transmitted to other units via communication RQ SI [n/ff] isplays front blower motor / status transmitted to other units via communication UTY X TIV TST uty ratio of front blower motor judged by / auto amp. Target discharge front air temperature (driver side) judged by / auto amp. depending on the temperature setting and the value from each sensor SS SU [w/m 2 ] Sunload value (passenger side) calculated by / auto amp. SS SU S [w/m 2 ] TRT /T RRI T S [ ( )] Sunload sensor value converted from sunload sensor signal (passenger side) received from sunload sensor Target discharge front air temperature (passenger side) judged by / auto amp. depending on the temperature setting and the value from each sensor Rear in-vehicle sensor value converted from rear in-vehicle sensor signal received from rear in-vehicle sensor. RRI T [ ( )] In-vehicle temperature (rear side) value calculated by / auto amp. RR IT T [ ( )] Rear evaporator fin temperature value calculated by / auto amp. RR RQ SI RR UTY RR X [n/ff] isplays rear blower motor / status transmitted to other units via communication uty ratio of rear blower motor judged by / auto amp. Target discharge rear air temperature (driver side) judged by / auto amp. depending on the temperature setting and the value from each sensor T [ ( )] ngine coolant temperature signal value received from via communication VI S onitor item [Unit] [km/h (mph)] escription Vehicle speed signal value received from combination meter via communication V TST Test item heck each output device escription The operation check of air conditioning system can be performed by selecting the mode. Refer to the following table for the conditions of each mode. ront mode door motor position -40 Test item 1 2 3 4 5 6 7 VT VT / / T / Intake door motor position R R 20% R 20% R R R R ront air mix door motor (driver side) position U U U U T U T U T U T ront air mix door motor (passenger side) position U U U U T U T U T U T ront blower motor control signal duty ratio 35% 35% 59% 59% 89% 89% 35% agnet clutch Upper ventilator door motor position S S S S S Rear mode door motor position Rear air mix door motor position Rear blower motor control signal duty ratio VT VT / / T T T U U U U T U T U T U T 35% 35% 59% 59% 89% 89% 35%

ISIS SYST (V) < SYST SRITI > [UTTI IR ITII] Rear / relay Ionizer * ront display (Ion mode) * *: With S (advanced climate control system) T: erform the inspection of each output device after starting the engine because the compressor is operated. WR SURT T ST RRT WR ST R RY ST R RY ST Test item 1 2 3 4 5 6 7 QUI QUI QUI QUI Work item escription Refer to S SSR USTT * SW ST * RR T ST RRT Setting change of temperature setting trimmer (front) can be performed. Setting change of foot position setting trimmer can be performed. Setting change of inlet port memory function (R) can be performed. Setting change of inlet port memory function (R) can be performed. Setting change of exhaust gas / outside odor detecting sensor sensitivity adjustment function can be performed. Setting change of auto intake switch interlocking movement change function can be performed. Setting change of temperature setting trimmer (rear) can be performed. *: With S (advanced climate control system) T: When the battery cable is disconnected from the negative terminal or when the battery voltage becomes 10 V or less, the setting of WR SURT may be cancelled. -68, "RT UT- TI IR ITI- I SYST : Temperature Setting Trimmer (ront)" -68, "RT UT- TI IR ITI- I SYST : oot osition Setting Trimmer" -69, "RT UT- TI IR ITI- I SYST : Inlet ort emory unction (R)" -69, "RT UT- TI IR ITI- I SYST : Inlet ort emory unction (R)" -70, "S (- V IT - TR SYST) : xhaust as / utside dor etecting Sensor Sensitivity djustment unction" -70, "S (- V IT - TR SYST) : uto Intake Switch Interlocking ovement hange unction" -68, "RT UT- TI IR ITI- I SYST : Temperature Setting Trimmer (ront)" -41

/ UT. < U ISIS IRTI > [UTTI IR ITII] U ISIS IRTI / UT. Reference Value SUT-III T ITR RR VUS II:0000000006275886 onitor item ondition Value/Status T S Ignition switch I-V T Ignition switch IT T S Ignition switch SU S Ignition switch S Ignition switch I-V Ignition switch IT T Ignition switch SU S Ignition switch RQ SI RQ SI ngine: Run at idle after warming up ngine: Run at idle after warming up / switch: (ompressor operation status) / switch: ront blower motor: ront blower motor: quivalent to ambient temperature quivalent to in-vehicle temperature (front side) quivalent to front evaporator fin temperature quivalent to sunload (driver side) quivalent to ambient temperature quivalent to in-vehicle temperature (front side) quivalent to front evaporator fin temperature quivalent to sunload (driver side) UTY ngine: Run at idle after ront blower motor: 25 81 warming up ront blower motor: 0 X Ignition switch Value according to target air flow temperature (driver side) SS SU Ignition switch SS SU S Ignition switch TRT /T Ignition switch RRI T S Ignition switch RRI T Ignition switch RR IT T Ignition switch RR RQ SI RR UTY ngine: Run at idle after warming up ngine: Run at idle after warming up Rear blower motor: Rear blower motor: n ff n ff quivalent to sunload (passenger side) quivalent to sunload (passenger side) Value according to target air flow temperature (passenger side) quivalent to in-vehicle temperature (rear side) quivalent to in-vehicle temperature (rear side) quivalent to rear evaporator fin temperature n ff Rear blower motor: 25 81 Rear blower motor: 0-42

/ UT. < U ISIS IRTI > [UTTI IR ITII] TRI YUT onitor item ondition Value/Status RR X Ignition switch T Ignition switch VI S riving Value according to target air flow temperature (rear side) quivalent to engine coolant temperature quivalent to speedometer reading YSI VUS Terminal o. (Wire color) escription + Signal name 1 () 2 () 3 (Y/) 4 (V) 5 *1 (W) 6 (V/W) 7 (W/R) 8 (R/) 9 (R) - Input/ utput Input/ utput ondition II0787ZZ Value (pprox.) round round attery power supply Input Ignition switch attery voltage round power supply Input Ignition switch attery voltage round round Ionizer (/) control signal / auto amp. connection recognition signal utput Ignition switch ront blower motor: ront blower motor: round mbient sensor signal Input Ignition switch round round Rear in-vehicle sensor signal Sunload sensor (driver side) signal 0 V 12 V utput Ignition switch 12 V Input Input Ignition switch Ignition switch 0 4.8 V utput voltage varies with ambient temperature 0 4.8 V utput voltage varies with in-vehicle temperature (rear side) 0 4.8 V utput voltage varies with sunload (driver side) amount 10 *1 (V/W) round xhaust gas / outside odor detecting sensor signal Input Ignition switch T: The signal is depending on measurement environment of the vehicle ZI1163-43

/ UT. < U ISIS IRTI > [UTTI IR ITII] Terminal o. (Wire color) escription + Signal name Input/ utput ondition Value (pprox.) 11 (W) round ommunication signal (/ auto amp. Rear / control) utput Ignition switch SI1521 14 (/) round ront blower motor control signal utput Ignition switch ront fan speed: 1st speed (manual) SII0096ZZ 16 (R/) round ach door motor I signal Input/ utput Ignition switch SI1453 17 (/Y) 21 () 22 () 23 (R/) 25 *1, * (R) 26 () 27 (R) 28 (R) 29 () round ach door motor power supply - utput Ignition switch 12 V Input/ utput round round Ignition power supply Input Ignition switch attery voltage Sensor ground round ront in-vehicle sensor signal Input Ignition switch round Intake sensor signal Input Ignition switch round Sunload sensor (passenger side) signal Input Ignition switch 0 4.8 V utput voltage varies with in-vehicle temperature (front side) 0 4.8 V utput voltage varies with front evaporator fin temperature 0 4.8 V utput voltage varies with sunload (passenger side) amount 31 (/) round ommunication signal (Rear / control / auto amp.) Input Ignition switch SI1522-44

/ UT. < U ISIS IRTI > [UTTI IR ITII] Terminal o. (Wire color) escription + Signal name Input/ utput ondition Value (pprox.) 34 (/) round Rear blower motor control signal utput Ignition switch Rear fan speed: 1st speed (manual) 37 () 38 (/W) *1: With S (advanced climate control system) *2: / auto amp. is not used for control. ail-safe II:0000000006275887 I-S UTI If a communication error exists between the / auto amp., and the V control unit and preset switch for 30 seconds or longer, air conditioning is controlled under the following conditions: When ambient temperature is less than 3 (37 ) and engine coolant temperature is less than 56 (133 ) When ambient temperature is 3 (37 ) or more, or engine coolant temperature is 56 (133 ) or more T Index round round Rear / relay control signal utput ompressor ir outlet ir inlet lower fan speed Set temperature ompressor ir outlet ir inlet lower fan speed Set temperature T Ignition switch Rear blower motor: Rear blower motor: : : : R (resh air intake) : UT : Setting before communication error occurs : : UT : 20% R (20% fresh air intake) : UT : Setting before communication error occurs Items (SUT-III screen terms) 0 V 12 V Reference U1000 IRUIT -72, "T ogic" U1010 TR UIT () -73, "T ogic" 2578 I-VI SSR -74, "T ogic" 2579 I-VI SSR -74, "T ogic" 257 IT SR -77, "T ogic" 257 IT SR -77, "T ogic" 2581 IT SSR -80, "T ogic" 2582 IT SSR -80, "T ogic" SII0096ZZ II:0000000006275888-45

/ UT. < U ISIS IRTI > [UTTI IR ITII] T Items (SUT-III screen terms) Reference 262 *1 S SSR -83, "T ogic" 262 *1 S SSR -83, "T ogic" 2630 *2 SU SSR -86, "T ogic" 2631 *2 SU SSR -86, "T ogic" 2632 R IRIX R T -89, "T ogic" 2633 R IRIX R T -89, "T ogic" 2634 SS IR IX R T -91, "T ogic" 2635 SS IR IX R T -91, "T ogic" 2636 R VT R I -93, "T ogic" 2637 R / R I -93, "T ogic" 2638 R /1 R I -93, "T ogic" 2639 R R I -93, "T ogic" 263 R R I -95, "T ogic" 263 20 R R I -95, "T ogic" 263 R R I -95, "T ogic" 2654 /2 R I -93, "T ogic" 2655 /2 R I -93, "T ogic" 2657 *1 S SSR IRUIT -83, "T ogic" 2658 *1 S SSR IRUIT -83, "T ogic" 2661 UR VT R T -97, "T ogic" 2662 UR VT R T -97, "T ogic" 2663 UR VT R T -97, "T ogic" 2664 RR IR IX R T -99, "T ogic" 2665 RR IR IX R T -99, "T ogic" 2666 RR R T -101, "T ogic" 2667 *2 SS SU SSR -103, "T ogic" 2668 *2 SS SU SSR -103, "T ogic" 2669 RR R T -101, "T ogic" 266 RR R T -101, "T ogic" 266 RR I-VI S -106, "T ogic" 266 RR I-VI S -106, "T ogic" 270 / UT. -109, "T ogic" *1: With S (advanced climate control system) *2: erform self-diagnosis under sunshine. When performing indoors, aim a light (more than 60 W) at sunload sensor, otherwise self-diagnosis indicates even though the sunload sensor is functioning normally. T: If all of door motor Ts (2632, 2633, 2634, 2635, 2636, 2637, 2638, 2639, 263, 263, 263, 2654, 2655, 2661, 2662, 2663, 2664, 2665, 2666, 2669, and 266) are detected, check door motor communication circuit. Refer to -120, "iagnosis rocedure". -46

, I /R < U ISIS IRTI > [UTTI IR ITII], I /R ist of U Reference II:0000000006275889 I /R U Reference -72, "Reference Value" -93, "ail-safe" -96, "T Inspection riority hart" -98, "T Index" S-15, "Reference Value" S-21, "ail-safe" S-22, "T Index" -47

UTTI IR ITII SYST < WIRI IR > [UTTI IR ITII] WIRI IR UTTI IR ITII SYST Wiring iagram II:0000000006275890 IW0795-48

UTTI IR ITII SYST < WIRI IR > [UTTI IR ITII] IW0796-49

UTTI IR ITII SYST < WIRI IR > [UTTI IR ITII] IW0797-50

UTTI IR ITII SYST < WIRI IR > [UTTI IR ITII] IW0798-51

UTTI IR ITII SYST < WIRI IR > [UTTI IR ITII] IW0799-52

UTTI IR ITII SYST < WIRI IR > [UTTI IR ITII] IW0800-53

UTTI IR ITII SYST < WIRI IR > [UTTI IR ITII] IW0801-54

UTTI IR ITII SYST < WIRI IR > [UTTI IR ITII] IW0802-55

UTTI IR ITII SYST < WIRI IR > [UTTI IR ITII] IW0803-56

UTTI IR ITII SYST < WIRI IR > [UTTI IR ITII] IW0804-57

UTTI IR ITII SYST < WIRI IR > [UTTI IR ITII] IW0805-58

UTTI IR ITII SYST < WIRI IR > [UTTI IR ITII] IW0806-59

ISIS RIR WR W < SI ISTI > [UTTI IR ITII] SI ISTI ISIS RIR WR W Work low VR SQU II:0000000006275891 TI W 1.ITRVIW R UTI Interview the symptom to the customer. I0313-60

ISIS RIR WR W < SI ISTI > [UTTI IR ITII] >> T 2. 2.SYT heck the symptom from the customer's information. >> T 3. 3.SI ISTI heck the operation of each part. heck that any symptom occurs other than the interviewed symptom. >> T 4. 4.S-ISIS WIT SUT-III erform the self-diagnosis with SUT-III. heck that any T is detected. Is any T detected? YS >> T 5. >> T 6. 5.TRU ISIS Y T erform the trouble diagnosis for the detected T. Specify the malfunctioning part. >> T 9. 6.I-S TIVTI heck that the symptom is applied to the fail-safe activation. oes the fail-safe activate? YS >> T 7. >> T 8. 7.SYST ISIS erform the system diagnosis for the system that the fail-safe activates. Specify the malfunctioning part. >> T 9. 8.SYT ISIS erform the symptom diagnosis. Specify the malfunctioning part. >> T 9. 9.UTI RT RIR Repair or replace the malfunctioning part. >> T 10. 10.RIR (S-ISIS WIT SUT-III) erform the self-diagnosis with SUT-III. heck that any T is not detected. rase T if T is detected before the repair. heck that T is not detected again. Is any T detected? YS >> T 5. >> T 11. 11.RIR (RTI ) heck the operation of each part. oes it operate normally? YS >> ISTI >> T 3. -61

RTI ISTI < SI ISTI > [UTTI IR ITII] RTI ISTI RT UTTI IR ITII SYST RT UTTI IR ITII SYST : Work rocedure SRITI The purpose of the operational check is to check that the individual system operates normally. heck condition RTI ISTI 1. RY UTI : ngine running at normal operating temperature. 1. Set temperature control dial (driver side) to 32.0 (90 ). 2. ress switch. 3. Turn ignition switch. 4. Turn ignition switch. 5. ress UT switch. 6. heck that set temperature is maintained. YS >> T 2. >> T 12. 2. RT WR TR 1. Start engine. 2. perate fan switch. 3. heck that fan speed changes. heck operation for all fan speeds. YS >> T 3. >> T 12. 3. ISR IR ( SWIT SWIT) II:0000000006275892 1. perate fan switch to set the fan speed to maximum speed. 2. perate switch and switch. 3. heck that air outlets change according to each indicated air outlet by placing a hand in front of the outlets. Refer to VT-6, "VTITI SYST (RT IR ITII) : System escription". YS >> T 4. >> T 12. 4. ISR IR (UR VTITR SWIT) 1. ress switch to set the air outlet to other than / or. 2. ress upper ventilator switch. The upper ventilator switch indicator is turns. 3. heck that air flow blows from upper ventilator. 4. ress upper ventilator switch again. The upper ventilator switch indicator is turns. 5. heck that air flow from upper ventilator stops. YS-1 >> With S (advanced climate control system): T 5. YS-2 >> Without S (advanced climate control system): T 6. >> T 12. 5. IT IR [WIT S (V IT TR SYST)] 1. ress intake switch to set the air inlet to recirculation. The intake switch indicator turns. 2. isten to intake sound and confirm air inlets change. 3. ress intake switch again to set the air inlet to fresh air intake. The intake switch indicator turns. 4. isten to intake sound and confirm air inlets change. -62

RTI ISTI < SI ISTI > [UTTI IR ITII] YS >> T 7. >> T 12. 6. IT IR [WITUT S (V IT TR SYST)] 1. ress R switch to set the air inlet to recirculation. The R switch indicator turns. 2. isten to intake sound and confirm air inlets change. 3. ress R switch to set the air inlet to fresh air intake. The R switch indicator turns and R switch indicator turns. 4. isten to intake sound and confirm air inlets change. YS >> T 7. >> T 12. 7. RSSR 1. ress / switch. The / switch indicator is turns. 2. heck visually and by sound that the compressor operates. 3. ress / switch again. The / switch indicator is turns. 4. heck that compressor stops. YS >> T 8. >> T 12. 8. ISR IR TRTUR (/R IT TRTUR USTT UTI) 1. perate temperature control dial (driver side). 2. heck that discharge air temperature (driver side) changes. 3. perate temperature control dial (passenger side). The U switch indicator is turns. 4. heck that the discharge air temperature (passenger side) changes. 5. ress U switch. The U switch indicator is turns. 6. heck that air temperature setting (/R) is unified to the driver side temperature setting. YS >> T 9. >> T 12. 9. WIT TRTUR STTI WR 1. perate compressor. 2. perate temperature control dial (driver side) and lower the set temperature to 18 (60 ). 3. heck that cool air blows from the air outlets. YS >> T 10. >> T 12. 10. TRTUR IRS 1. perate temperature control dial (driver side) and raise the set temperature to 32 (90 ). 2. heck that warm air blows from the air outlets. YS >> T 11. >> T 12. 11. UT 1. ress UT switch to confirm that UT is indicated on the display. 2. perate temperature control dial (driver side) to check that fan speed or air outlet changes (the air outlet or fan speed varies depending on the ambient temperature, in-vehicle temperature (front side), set temperature, and etc.). YS >> ISTI >> T 12. -63

RTI ISTI < SI ISTI > [UTTI IR ITII] 12. S-ISIS WIT SUT-III 1. erform self-diagnosis with SUT-III. 2. heck that any T is detected. Is any T detected? YS >> Refer to -45, "T Index" and perform the appropriate diagnosis. >> T 13. 13. I-S TIVTI heck that symptom is applied to the fail-safe activation. Refer to -45, "ail-safe". >> Refer to -133, "iagnosis hart y Symptom" and perform the appropriate diagnosis. RR UTTI IR ITII SYST RR UTTI IR ITII SYST : Work rocedure II:0000000006275893 SRITI The purpose of the operational check is to check that the individual system operates normally. T: heck that front automatic air conditioning system operates normally. Refer to -133, "iagnosis hart y Symptom". heck condition RTI ISTI ront / ontrol peration 1. RR TR UTI 1. ress RR switch. The RR switch indicator turns. 2. heck that front display changes to state indication display (rear control mode) and that rear automatic air conditioning system starts. 3. ress RR switch again. The RR switch indicator turns. 4. heck that rear control mode released. (rear automatic air conditioning system operates continuously) YS >> T 2. >> T 8. 2. RR WR TR 1. ress RR switch. 2. perate fan switch. 3. heck that fan speed changes. heck operation for all fan speeds. YS >> T 3. >> T 8. 3. ISR IR 1. perate fan switch to set the fan speed to maximum speed. 2. perate switch. 3. heck that air outlets change according to each indicated air outlet by placing a hand in front of the outlets. Refer to VT-7, "VTITI SYST (RR IR ITII) : System escription". YS >> T 4. >> T 8. 4. ISR IR TRTUR 1. perate temperature control dial (driver side). : ngine running at normal operating temperature. : ront air conditioning system operate. -64

RTI ISTI < SI ISTI > [UTTI IR ITII] 2. heck that discharge air temperature changes. YS >> T 5. >> T 8. 5. WIT TRTUR STTI WR 1. perate temperature control dial (driver side) and lower the set temperature to 18 (60 ). 2. heck that cool air blows from the air outlets. YS >> T 6. >> T 8. 6. TRTUR IRS 1. perate temperature control dial (driver side) and raise the set temperature to 32 (90 ). 2. heck that warm air blows from the air outlets. YS >> T 7. >> T 8. 7. UT 1. ress UT switch. 2. perate temperature control dial (driver side) to check that fan speed or air outlet changes (the air outlet or fan speed varies depending on the ambient temperature, in-vehicle temperature (rear side), set temperature, and etc.). YS >> ISTI >> T 8. 8. S-ISIS WIT SUT-III 1. erform self-diagnosis with SUT-III. 2. heck that any T is detected. Is any T detected? YS >> Refer to -45, "T Index" and perform the appropriate diagnosis. >> Refer to -135, "iagnosis hart y Symptom" and perform the appropriate diagnosis. Rear / ontrol peration 1. RR WR TR 1. ress UT switch. 2. perate fan switch. 3. heck that fan speed changes. heck operation for all fan speeds. YS >> T 2. >> T 7. 2. ISR IR 1. perate fan switch to set the fan speed to maximum speed. 2. perate switch. 3. heck that air outlets change according to each indicated air outlet by placing a hand in front of the outlets. Refer to VT-7, "VTITI SYST (RR IR ITII) : System escription". YS >> T 3. >> T 7. 3. ISR IR TRTUR 1. perate temperature control switch. 2. heck that discharge air temperature changes. -65

RTI ISTI < SI ISTI > [UTTI IR ITII] YS >> T 4. >> T 7. 4. WIT TRTUR STTI WR 1. perate temperature control switch and lower the set temperature to 18. 2. heck that cool air blows from the air outlets. YS >> T 5. >> T 7. 5. TRTUR IRS 1. perate temperature control switch and raise the set temperature to 32. 2. heck that warm air blows from the air outlets. YS >> T 6. >> T 7. 6. UT 1. ress UT switch. 2. perate temperature control switch to check that fan speed or air outlet changes (the air outlet or fan speed varies depending on the ambient temperature, in-vehicle temperature (rear side), set temperature, and etc.). YS >> ISTI >> T 7. 7. S-ISIS WIT SUT-III 1. erform self-diagnosis with SUT-III. 2. heck that any T is detected. Is any T detected? YS >> Refer to -45, "T Index" and perform the appropriate diagnosis. >> Refer to -135, "iagnosis hart y Symptom" and perform the appropriate diagnosis. S (V IT TR SYST) S (V IT TR SYST) : Work rocedure II:0000000006275894 SRITI The purpose of the operational check is to check that the individual system operates normally. T: heck that front automatic air conditioning system operates normally. Refer to -62, "RT UTTI IR ITII SYST : Work rocedure". heck condition RTI ISTI : ngine running 1. SUSTR TR heck the ionizer operation sound (whirring sound) in the duct by putting an ear to the center ventilator grille (driver side) outlet while pressing fan switch and switch alternately. T: lasmacluster ion technology developed by Sharp orporation is installed in this item. lasmacluster is a trademark of Sharp orporation. YS >> T 2. >> T 4. 2. SUSTR TR RTI STTUS -66

RTI ISTI < SI ISTI > [UTTI IR ITII] perate fan switch. Visually check that status indicator in front display changes in accordance with the following table. 2nd 5th an speed QUI ront display (ion indicator) T: lasmacluster ion technology developed by Sharp orporation is installed in this item. lasmacluster is a trademark of Sharp orporation. YS >> T 3. >> T 4. 3. UTTI IT TR (XUST S / UTSI R TTI IS) 1. perate fan switch to set the fan speed to maximum speed. 2. ress auto intake switch to set the air inlet to recirculation. The auto intake switch indicator and intake switch indicator turn. 3. isten to intake sound and confirm air inlets change. 4. Wait approximately for 5 minutes until air inlet switches to fresh air intake. 5. pply cigarette smoke or similar substance to exhaust gas / outside odor detecting sensor portion. 6. isten to intake sound and confirm air inlets change to recirculation. YS >> ISTI >> T 4. 4. S-ISIS WIT SUT-III 1. erform self-diagnosis with SUT-III. 2. heck that any T is detected. Is any T detected? YS >> Refer to -45, "T Index" and perform the appropriate diagnosis. >> Refer to -135, "iagnosis hart y Symptom" and perform the appropriate diagnosis. -67

SYST STTI < SI ISTI > [UTTI IR ITII] SYST STTI RT UTTI IR ITII SYST RT UTTI IR ITII SYST : Temperature Setting Trimmer (ront) II:0000000006275896 SRITI If the temperature felt by the customer is different from the front air flow temperature controlled by the temperature setting, the / auto amp. control temperature can be adjusted to compensate for the temperature setting. W T ST With SUT-III erform T ST RRT of V work support item. T ST RRT Work support items isplay ( ) isplay ( ) T: When 3.0 ( 6 ) is corrected on the temperature setting set as 25.0 (77 ) the temperature controlled by / auto amp. is 25.0 (77 ) 3.0 ( 6 ) = 22.0 (72 ) and the temperature becomes lower than the temperature setting. When the battery cable is disconnected from the negative terminal or when the battery voltage becomes 10 V or less, the setting of the difference between the set temperature and control temperature may be cancelled. RT UTTI IR ITII SYST : oot osition Setting Trimmer SRITI In T mode, the air blowing to can change /. W T ST With SUT-III erform the W ST of V work support item. 3.0 6 2.5 5 2.0 4 1.5 3 1.0 2 0.5 1 0 (initial status) 0 (initial status) 0.5 1 1.0 2 1.5 3 2.0 4 2.5 5 3.0 6 II:0000000006275897 W ST Work support items efroster door position isplay uto control anual control ode1 S ode2 (initial status) ode3 S ode4 S S -68

SYST STTI < SI ISTI > [UTTI IR ITII] T: When the battery cable is disconnected from the negative terminal or when the battery voltage becomes 10 V or less, the setting of the discharge air mix ratio in T mode may be cancelled. RT UTTI IR ITII SYST : Inlet ort emory unction (R) II:0000000006275898 SRITI If the ignition switch is turned to the position while the intake switch is set to (fresh air intake), erform the memory or o not perform the memory of intake switch (fresh air intake) condition can be selected. If erform the memory was set, the intake switch will be (fresh air intake) when turning the ignition switch to the position again. If o not perform the memory was set, the air inlets will be controlled automatically when turning the ignition switch to the position again. W T ST With SUT-III erform the R RY ST of V work support item. Work support items isplay Setting WITUT erform the memory of manual R R RY ST WIT (initial status) o not perform the memory of manual R (auto control) T: When the battery cable is disconnected from the negative terminal or when the battery voltage becomes 10 V or less, the setting of the R memory function may be cancelled. RT UTTI IR ITII SYST : Inlet ort emory unction (R) II:0000000006275899 SRITI If the ignition switch is turned to the position while the intake switch is set to (recirculation), erform the memory or o not perform the memory of intake switch (recirculation) condition can be selected. If erform the memory was set, the intake switch will be (recirculation) when turning the ignition switch to the position again. If o not perform the memory was set, the air inlets will be controlled automatically when turning the ignition switch to the position again. W T ST With SUT-III erform the R RY ST of V work support item. Work support items isplay Setting WITUT (initial status) erform the memory of manual R R RY ST WIT o not perform the memory of manual R (auto control) T: When the battery cable is disconnected from the negative terminal or when the battery voltage becomes 10 V or less, the setting of the R memory function may be cancelled. RR UTTI IR ITII SYST RR UTTI IR ITII SYST : Temperature Setting Trimmer (Rear) II:0000000006275900 SRITI -69

SYST STTI < SI ISTI > [UTTI IR ITII] If the temperature felt by the customer is different from the rear air flow temperature controlled by the temperature setting, the / auto amp. control temperature can be adjusted to compensate for the temperature setting. W T ST With SUT-III erform RR T ST RRT of V work support item. Work support items isplay ( ) isplay ( ) 3.0 6 2.5 5 2.0 4 1.5 3 1.0 2 0.5 1 RR T ST RRT 0 (initial status) 0 (initial status) 0.5 1 1.0 2 1.5 3 2.0 4 2.5 5 3.0 6 T: When 3.0 ( 6 ) is corrected on the temperature setting set as 25.0 (77 ) the temperature controlled by / auto amp. is 25.0 (77 ) 3.0 ( 6 ) = 22.0 (72 ) and the temperature becomes lower than the temperature setting. When the battery cable is disconnected from the negative terminal or when the battery voltage becomes 10 V or less, the setting of the difference between the set temperature and control temperature may be cancelled. S (V IT TR SYST) S (V IT TR SYST) : xhaust as / utside dor etecting Sensor Sensitivity djustment unction II:0000000006275901 SRITI ccording to customer s sense of smell, exhaust gas / outside odor detecting sensor sensitivity can be changed. W T ST With SUT-III erform the S SSR USTT of V work support item. Work support items isplay Setting 2 ess sensitive setting than display 1 (R later than display 1.) 1 ess sensitive setting than normal setting (R later than normal operation.) S SSR USTT 0 (initial status) ormal 1 ore sensitive setting than normal setting (R earlier than normal operation.) 2 ore sensitive setting than display 1 (R earlier than display 1.) T: When the battery cable is disconnected from the negative terminal or when the battery voltage becomes 10 V or less, the setting of WR SURT may be cancelled. S (V IT TR SYST) : uto Intake Switch Interlocking -70

SYST STTI < SI ISTI > [UTTI IR ITII] ovement hange unction II:0000000006275902 SRITI ondition for interlocking movement of auto intake switch and / switch can be changed. In addition operation of the auto intake switch, which activates the automatic intake control (exhaust gas / outside odor detecting mechanism), can be set to become available when the / switch is. W T ST With SUT-III erform the SW ST of V work support item. Work support items isplay Setting Initial setting Setting 1 Setting 2 Setting 3 SW ST ode1 Initial setting ode2 Setting 1 ode3 Setting 2 ode4 Setting 3 When the auto intake switch is, the / switch is also turned in synchronization with the auto intake switch. ontrol of the auto intake switch is functional even when the / switch is turned. When the auto intake switch is, the / switch is not turned in synchronization with the auto intake switch. ontrol of the auto intake switch is functional even when the / switch is turned. When the auto intake switch is, the / switch is also turned in synchronization with the auto intake switch. When the / switch is turned, the auto intake switch is turned in synchronization with the / switch. uto intake switch can be turned only when / switch is. When the / switch is turned, the auto intake switch is turned in synchronization with the / switch. T: When the battery cable is disconnected from the negative terminal or when the battery voltage becomes 10 V or less, the setting of WR SURT may be cancelled. -71

U1000 IRUIT < T/IRUIT ISIS > [UTTI IR ITII] T/IRUIT ISIS U1000 IRUIT escription II:0000000006275903 (ontroller rea etwork) is a serial communication system for real time application. It is an on-vehicle multiplex communication system with high data communication speed and excellent error detection ability. any electronic control units are equipped onto vehicles, and each control unit shares information and links with other control units during operation (not independent). In communication, control units are connected with two communication lines (- line, - line) allowing a high rate of information transmission with less wiring. ach control unit transmits/receives data but selectively reads required data only. ommunication Signal hart. Refer to -28, " UITI SYST : ommunication Signal hart". T ogic T TTI I II:0000000006275904 T Items (SUT-III screen terms) T detection condition ossible cause U1000 IRUIT When / auto amp. is not transmitting or receiving communication signal for 2 or more seconds. communication system T IRTI RUR 1.RR S-ISIS With SUT-III 1. Turn ignition switch and wait for 2 seconds or more. 2. Select Self iagnostic Result mode of V using SUT-.III 3. heck T. Is T detected? YS >> Refer to -72, "iagnosis rocedure". >> Refer to I-40, "Intermittent Incident". iagnosis rocedure II:0000000006275905 1. UITI SYST heck communication system. Refer to -18, "Trouble iagnosis low hart". >> ISTI -72

U1010 TR UIT () < T/IRUIT ISIS > [UTTI IR ITII] U1010 TR UIT () escription II:0000000006275906 Initial diagnosis of / auto amp. T ogic T TTI I II:0000000006275907 T U1010 T IRTI RUR 1.RR S-ISIS With SUT-III 1. Turn ignition switch. 2. Select Self iagnostic Result mode of V using SUT-.III 3. heck T. Is T detected? YS >> Refer to -73, "iagnosis rocedure". >> ISTI iagnosis rocedure Items (SUT-III screen terms) TR UIT () 1.R / UT. Replace / auto amp.. Refer to -146, "Removal and Installation". >> ISTI T detection condition When detecting error during the initial diagnosis of controller of / auto amp. / auto amp. ossible cause II:0000000006275908-73

2578, 2579 RT I-VI SSR < T/IRUIT ISIS > [UTTI IR ITII] 2578, 2579 RT I-VI SSR T ogic II:0000000006275909 T TTI I T: If T is displayed along with T U1000, first perform the trouble diagnosis for T U1000. Refer to - 72, "T ogic". If T is displayed along with T U1010, first perform the trouble diagnosis for T U1010. Refer to - 73, "T ogic". T Items (SUT-III screen terms) T detection condition ossible cause 2578 2579 I-VI SSR The front in-vehicle sensor recognition temperature is too high. The front in-vehicle sensor recognition temperature is too low. ront in-vehicle sensor / auto amp. arness or connectors (The sensor circuit is open or shorted.) T IRTI RUR 1.RR T IRTI RUR With SUT-III 1. Turn ignition switch. 2. Select Self iagnostic Result mode of V using SUT-III. 3. heck T. Is T detected? YS >> Refer to -106, "iagnosis rocedure". >> ISTI iagnosis rocedure II:0000000006275910 1. RT I-VI SSR WR SUY 1. Turn ignition switch. 2. isconnect front in-vehicle sensor connector. 3. Turn ignition switch. 4. heck voltage between front in-vehicle sensor harness connector and ground. + ront in-vehicle sensor onnector Terminal YS >> T 2. >> T 4. 2. RT I-V SSR RU IRUIT Voltage (pprox.) 73 1 round 5 V 1. Turn ignition switch. 2. isconnect / auto amp. connector. 3. heck continuity between front in-vehicle sensor harness connector and / auto amp. harness connector. ront in-vehicle sensor onnector Terminal ontinuity 73 2 round xisted -74

2578, 2579 RT I-VI SSR < T/IRUIT ISIS > [UTTI IR ITII] YS >> T 3. >> Repair harness or connector. 3. RT I-VI SSR heck front in-vehicle sensor. Refer to -107, "omponent Inspection". YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Replace front in-vehicle sensor. Refer to -148, "RT / UIT SSY : Removal and Installation". 4. RT I-V SSR WR SUY IRUIT R 1. Turn ignition switch. 2. isconnect / auto amp. connector. 3. heck continuity between front in-vehicle sensor harness connector and / auto amp. harness connector. ront in-vehicle sensor / auto amp. onnector Terminal onnector Terminal 73 1 50 27 xisted YS >> T 5. >> Repair harness or connector. 5. RT I-V SSR WR SUY IRUIT R RU SRT heck continuity between front in-vehicle sensor harness connector and ground. ront in-vehicle sensor onnector Terminal ontinuity ontinuity 73 1 round ot existed YS >> T 6. >> Repair harness or connector. 6. RT I-VI SSR WR SUY IRUIT R WR SRT 1. Turn ignition switch. 2. heck voltage between front in-vehicle sensor harness connector and ground. YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Repair harness or connector. omponent Inspection + ront in-vehicle sensor onnector Terminal 1. RT I-VI SSR 1. Turn ignition switch. 2. isconnect front in-vehicle sensor connector. 3. heck resistance between front in-vehicle sensor terminals. Voltage (pprox.) 73 1 round 0 V II:0000000006275911-75

2578, 2579 RT I-VI SSR < T/IRUIT ISIS > [UTTI IR ITII] Terminal 1 2 ondition Temperature: ( ) Resistance: kω 15 (5) 12.73 10 (14) 9.92 5 (23) 7.80 0 (32) 6.19 5 (41) 4.95 10 (50) 3.99 15 (59) 3.24 20 (68) 2.65 25 (77) 2.19 30 (86) 1.81 35 (95) 1.51 40 (104) 1.27 45 (113) 1.07 YS >> ISTI >> Replace front in-vehicle sensor. Refer to -148, "RT / UIT SSY : Removal and Installation". -76

257, 257 IT SSR < T/IRUIT ISIS > [UTTI IR ITII] 257, 257 IT SSR T ogic II:0000000006275912 T TTI I T: If T is displayed along with T U1000, first perform the trouble diagnosis for T U1000. Refer to - 72, "T ogic". If T is displayed along with T U1010, first perform the trouble diagnosis for T U1010. -73, "T ogic". T 257 257 Items (SUT-III screen terms) T IRTI RUR 1.RR T IRTI RUR With SUT-III 1. Turn ignition switch. 2. Select Self iagnostic Result mode of V using SUT-III. 3. heck T. Is T detected? YS >> Refer to -77, "iagnosis rocedure". >> ISTI iagnosis rocedure 1. IT SSR WR SUY 1. Turn ignition switch. 2. isconnect ambient sensor connector. 3. Turn ignition switch. 4. heck voltage between ambient sensor harness connector and ground. onnector IT SSR + mbient sensor Terminal YS >> T 2. >> T 4. 2. IT SSR RU IRUIT T detection condition The ambient sensor recognition temperature is too high. The ambient sensor recognition temperature is too low. Voltage (pprox.) 76 1 round 5 V ossible cause mbient sensor / auto amp. arness or connectors (The sensor circuit is open or shorted.) II:0000000006275913 1. Turn ignition switch. 2. isconnect / auto amp.connector. 3. heck continuity between ambient sensor harness connector and / auto amp. harness connector. mbient sensor onnector Terminal ontinuity 76 2 round xisted -77

257, 257 IT SSR < T/IRUIT ISIS > [UTTI IR ITII] YS >> T 3. >> Repair harness or connector. 3. IT SSR heck ambient sensor. Refer to -78, "omponent Inspection". YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Replace ambient sensor. Refer to -147, "Removal and Installation". 4. IT SSR WR SUY IRUIT R 1. Turn ignition switch. 2. isconnect / auto amp.connector. 3. heck continuity between ambient sensor harness connector and / auto amp. harness connector. mbient sensor / auto amp. onnector Terminal onnector Terminal 76 1 50 7 xisted YS >> T 5. >> Repair harness or connector. 5. IT SSR WR SUY IRUIT R RU SRT heck continuity between ambient sensor harness connector and ground. ontinuity onnector mbient sensor Terminal ontinuity 76 1 round ot existed YS >> T 6. >> Repair harness or connector. 6. IT SSR WR SUY IRUIT R WR SRT 1. Turn ignition switch. 2. heck voltage between ambient sensor harness connector and ground. onnector 76 1 round 0 V YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Repair harness or connector. omponent Inspection + mbient sensor Terminal Voltage (pprox.) II:0000000006275914 1. IT SSR 1. Turn ignition switch. 2. isconnect ambient sensor connector. 3. heck resistance between ambient sensor terminals. -78

257, 257 IT SSR < T/IRUIT ISIS > [UTTI IR ITII] Terminal ondition Temperature: ( ) Resistance: kω 15 (5) 12.73 10 (14) 9.92 5 (23) 7.80 0 (32) 6.19 5 (41) 4.95 10 (50) 3.99 1 2 15 (59) 3.24 20 (68) 2.65 25 (77) 2.19 30 (86) 1.81 35 (95) 1.51 40 (104) 1.27 45 (113) 1.07 YS >> ISTI >> Replace ambient sensor. Refer to -147, "Removal and Installation". -79

2581, 2582 IT SSR < T/IRUIT ISIS > [UTTI IR ITII] 2581, 2582 IT SSR T ogic II:0000000006275915 T TTI I T: If T is displayed along with T U1000, first perform the trouble diagnosis for T U1000. Refer to - 72, "T ogic". If T is displayed along with T U1010, first perform the trouble diagnosis for T U1010. -73, "T ogic". T Items (SUT-III screen terms) T detection condition ossible cause 2581 2582 IT SSR The intake sensor recognition temperature is too high. The intake sensor recognition temperature is too low. Intake sensor / auto amp. arness or connectors (The sensor circuit is open or shorted.) T IRTI RUR 1.RR T IRTI RUR With SUT-III 1. Turn ignition switch. 2. Select Self iagnostic Result mode of V using SUT-III. 3. heck T. Is T detected? YS >> Refer to -80, "iagnosis rocedure". >> ISTI iagnosis rocedure II:0000000006275916 1. IT SSR WR SUY 1. Turn ignition switch. 2. isconnect intake sensor connector. 3. Turn ignition switch. 4. heck voltage between intake sensor harness connector and ground. onnector + Intake sensor Terminal YS >> T 2. >> T 4. 2. IT SSR RU IRUIT Voltage (pprox.) 257 1 round 5 V 1. Turn ignition switch. 2. isconnect / auto amp. connector. 3. heck continuity between intake sensor harness connector and / auto amp. harness connector. Intake sensor onnector Terminal ontinuity 257 2 round xisted -80

2581, 2582 IT SSR < T/IRUIT ISIS > [UTTI IR ITII] YS >> T 3. >> Repair harness or connector. 3. IT SSR heck intake sensor. Refer to -81, "omponent Inspection". YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Replace intake sensor. Refer to -150, "Removal and Installation". 4. IT SSR WR SUY IRUIT R 1. Turn ignition switch. 2. isconnect / auto amp. connector. 3. heck continuity between intake sensor harness connector and / auto amp. harness connector. Intake sensor / auto amp. onnector Terminal onnector Terminal 257 1 50 28 xisted YS >> T 5. >> Repair harness or connector. 5. IT SSR WR SUY IRUIT R RU SRT heck continuity between intake sensor harness connector and ground. onnector Intake sensor Terminal 257 1 round ot existed YS >> T 6. >> Repair harness or connector. 6. IT SSR WR SUY IRUIT R WR SRT 1. Turn ignition switch. 2. heck voltage between intake sensor harness connector and ground. ontinuity ontinuity onnector YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Repair harness or connector. omponent Inspection 1. IT SSR + Intake sensor Terminal 1. Turn ignition switch. 2. isconnect intake sensor connector. 3. heck resistance between intake sensor terminals. Voltage (pprox.) 257 1 round 0 V II:0000000006275917-81

2581, 2582 IT SSR < T/IRUIT ISIS > [UTTI IR ITII] Terminal ondition Temperature: ( ) Resistance: kω 15 (5) 17.73 10 (14) 13.46 5 (23) 10.33 0 (32) 8.00 5 (41) 6.25 10 (50) 4.93 1 2 15 (59) 3.92 20 (68) 3.14 25 (77) 2.54 30 (86) 2.06 35 (95) 1.69 40 (104) 1.39 45 (113) 1.15 YS >> ISTI >> Replace intake sensor. Refer to -150, "Removal and Installation". -82

262, 262, 2657, 2658 XUST S/UTSI R TTI SSR < T/IRUIT ISIS > [UTTI IR ITII] 262, 262, 2657, 2658 XUST S/UTSI R TT- I SSR T ogic II:0000000006275918 T TTI I T: If T is displayed along with T U1000, first perform the trouble diagnosis for T U1000. Refer to - 72, "T ogic". If T is displayed along with T U1010, first perform the trouble diagnosis for T U1010. -73, "T ogic". T 262 262 2657 2658 Items (SUT-III screen terms) S SSR S SSR IRUIT T detection condition xhaust gas / outside odor detecting sensor duty ratio 15% or less. xhaust gas / outside odor detecting sensor duty ratio 85% or more. xhaust gas / outside odor detecting sensor duty ratio 0%. xhaust gas / outside odor detecting sensor duty ratio 100%. ossible cause xhaust gas / outside odor detecting sensor / auto amp. arness or connectors (The sensor circuit is open or shorted.) T IRTI RUR 1.RR T IRTI RUR With SUT-III 1. Turn ignition switch. 2. Select Self iagnostic Result mode of V using SUT-III. 3. heck T. Is T detected? YS >> Refer to -83, "iagnosis rocedure". >> ISTI iagnosis rocedure 1. US 1. Turn ignition switch. 2. heck 10 fuse [o.4, located in fuse block (/)] T: Refer to -140, "use, onnector and Terminal rrangement". YS >> T 2. >> Replace the blown fuse after repairing the affected circuit if a fuse is blown. 2. XUST S / UTSI R TTI SSR WR SUY 1. Turn ignition switch. 2. isconnect exhaust gas / outside odor detecting sensor connector. 3. Turn ignition switch. 4. heck voltage between exhaust gas / outside odor detecting sensor harness and ground. II:0000000006275919 + xhaust gas / outside odor detecting sensor onnector Terminal Voltage (pprox.) 117 1 round attery voltage -83

262, 262, 2657, 2658 XUST S/UTSI R TTI SSR < T/IRUIT ISIS > [UTTI IR ITII] YS >> T 3. >> Repair harness or connector between exhaust gas / outside odor detecting sensor and fuse block (/). 3. XUST S / UTSI R TTI SSR RU IRUIT 1. Turn ignition switch. 2. heck continuity between exhaust gas / outside odor detecting sensor harness connector and ground. xhaust gas / outside odor detecting sensor ontinuity onnector Terminal 117 2 round xisted YS >> T 4. >> Repair harness or connector. 4. XUST S / UTSI R TTI SSR SI IRUIT 1. Turn ignition switch. 2. heck voltage between exhaust gas / outside odor detecting sensor harness connector and ground. + xhaust gas / outside odor detecting sensor onnector Terminal Voltage (pprox.) 117 3 round 5 V YS >> Replace exhaust gas / outside odor detecting sensor. Refer to -151, "Removal and Installation". >> T 5. 5. XUST S / UTSI R TTI SSR SI IRUIT R 1. Turn ignition switch. 2. isconnect / auto amp.connector. 3. heck continuity between exhaust gas / outside odor detecting sensor harness connector and / auto amp. connector. xhaust gas / outside odor detecting sensor / auto amp. onnector Terminal onnector Terminal ontinuity 117 3 50 10 xisted YS >> T 6. >> Repair harness or connector. 6. XUST S / UTSI R TTI SSR SI IRUIT R RU SRT heck continuity between exhaust gas / outside odor detecting sensor harness connector and ground. xhaust gas / outside odor detecting sensor ontinuity onnector Terminal 117 3 round ot existed -84

262, 262, 2657, 2658 XUST S/UTSI R TTI SSR < T/IRUIT ISIS > [UTTI IR ITII] YS >> T 7. >> Repair harness or connector. 7. XUST S / UTSI R TTI SSR SI IRUIT R WR SRT heck voltage between exhaust gas / outside odor detecting sensor harness and ground. + xhaust gas / outside odor detecting sensor onnector Terminal YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Repair harness or connector. Voltage (pprox.) 117 3 round 0 V -85

2630, 2631 SU SSR (RIVR SI) < T/IRUIT ISIS > [UTTI IR ITII] 2630, 2631 SU SSR (RIVR SI) T ogic II:0000000006275920 T TTI I T: If T is displayed along with T U1000, first perform the trouble diagnosis for T U1000. Refer to - 72, "T ogic". If T is displayed along with T U1010, first perform the trouble diagnosis for T U1010. -73, "T ogic". Sunload sensor may register a malfunction when indoors, at dusk, or at other times when light is insufficient. When performing the diagnosis indoors, use a lamp (60 W or more) that is pointed at the sunload sensor. T Items (SUT-III screen terms) T detection condition ossible cause 2630 2631 SU SSR etected calorie at sunload sensor (driver side) 2832 W/m 2 (2436 kcal/m 2 h) or more. etected calorie at sunload sensor (driver side) 64.7 W/m 2 (55.6 kcal/m 2 h) or less. Sunload sensor / auto amp. arness or connectors [The sensor circuit (driver side) is open or shorted.] T IRTI RUR 1.RR T IRTI RUR With SUT-III 1. Turn ignition switch. 2. Select Self iagnostic Result mode of V using SUT-III. 3. heck T. Is T detected? YS >> Refer to -103, "iagnosis rocedure". >> ISTI iagnosis rocedure II:0000000006275921 1. SU SSR WR SUY 1. Turn ignition switch. 2. isconnect sunload sensor connector. 3. Turn ignition switch. 4. heck voltage between sunload sensor harness connector and ground. onnector + Sunload sensor Terminal YS >> T 2. >> T 4. 2. SU SSR RU IRUIT Voltage (pprox.) 74 2 round 5 V 1. Turn ignition switch. 2. isconnect / auto amp. connector. 3. heck continuity between sunload sensor harness connector and / auto amp. harness connector. Sunload sensor onnector Terminal ontinuity 74 3 round xisted -86

2630, 2631 SU SSR (RIVR SI) < T/IRUIT ISIS > [UTTI IR ITII] YS >> T 3. >> Repair harness or connector. 3. SU SSR heck sunload sensor. Refer to -104, "omponent Inspection". YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Replace sunload sensor. Refer to -149, "Removal and Installation". 4. SU SSR WR SUY IRUIT R 1. Turn ignition switch. 2. isconnect / auto amp. connector. 3. heck continuity between sunload sensor harness connector and / auto amp. harness connector. Sunload sensor / auto amp. onnector Terminal onnector Terminal 74 2 50 9 xisted YS >> T 5. >> Repair harness or connector. 5. SU SSR WR SUY IRUIT R RU SRT heck continuity between sunload sensor harness connector and ground. ontinuity onnector Sunload sensor Terminal ontinuity 74 2 round ot existed YS >> T 6. >> Repair harness or connector. 6. SU SSR WR SUY IRUIT R WR SRT 1. Turn ignition switch. 2. heck voltage between sunload sensor harness connector and ground. onnector YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Repair harness or connector. omponent Inspection + Sunload sensor Terminal Voltage (pprox.) 74 2 round 0 V II:0000000006275922 1. SU SSR 1. Turn ignition switch. 2. Reconnect sunload sensor connector and / auto amp. connector. 3. Turn ignition switch. 4. heck input voltage from sunload sensor between / auto amp. harness connector and ground. Refer to applicable table for normal value. -87

2630, 2631 SU SSR (RIVR SI) < T/IRUIT ISIS > [UTTI IR ITII] + / auto amp. onnector Terminal 50 9 round II1659 T: When checking indoors, use a lamp of approximately 60 W. ove the lamp towards and away from the sensor to check. The sunload amount produced by direct sunshine in fair weather is equivalent to approximately 0.770 kw/m 2 (662 kcal/m 2 h). YS >> ISTI >> Replace sunload sensor. Refer to -149, "Removal and Installation". -88

2632, 2633 RT IR IX R TR (RIVR SI) < T/IRUIT ISIS > [UTTI IR ITII] 2632, 2633 RT IR IX R TR (RIVR SI) T ogic T TTI I II:0000000006275923 T 2632 2633 Items (SUT-III screen terms) R IR IX R T T detection condition ront air mix door motor (driver side) R position 95% or more ront air mix door motor (driver side) R position 5% or less ossible cause ront air mix door motor (driver side) (R internal circuit is open or shorted) ront air mix door motor (driver side) installation condition / auto amp. arness and connector (I communication line is open or shorted) T IRTI RUR 1.RR T IRTI RUR With SUT-III 1. Turn ignition switch. 2. Select Self iagnostic Result mode of V using SUT-III. 3. heck T. Is T detected? YS >> Refer to -89, "iagnosis rocedure". >> ISTI iagnosis rocedure II:0000000006275924 1. RT IR IX R TR (RIVR SI) UITI SI 1. Turn ignition switch. 2. heck output waveform between front air mix door motor harness connector and ground with the oscilloscope. + ront air mix door motor utput waveform onnector Terminal 252 3 round YS >> T 2. >> T 3. 2. ISTTI RT IR IX R TR (RIVR SI) heck front air mix door motor (driver side) is properly installed. Refer to -152, "xploded View". YS >> Replace front air mix door motor (driver side). Refer to -153, "IR IX R TR : Removal and Installation". >> Repair or replace malfunctioning part. SI1453-89

2632, 2633 RT IR IX R TR (RIVR SI) < T/IRUIT ISIS > [UTTI IR ITII] 3. RT IR IX R TR (RIVR SI) UITI SI IRUIT 1. Turn ignition switch. 2. isconnect front air mix door motor and / auto amp. connector. 3. heck continuity between front air mix door motor harness connector and / auto amp. harness connector. ront air mix door motor / auto amp. onnector Terminal onnector Terminal ontinuity 252 3 50 16 xisted YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Repair harness or connector. -90

2634, 2635 RT IR IX R TR (SSR SI) < T/IRUIT ISIS > [UTTI IR ITII] 2634, 2635 RT IR IX R TR (SSR SI) T ogic T TTI I T 2634 2635 Items (SUT-III screen terms) SS IR IX R T T IRTI RUR 1.RR T IRTI RUR With SUT-III 1. Turn ignition switch. 2. Select Self iagnostic Result mode of V using SUT-III. 3. heck T. Is T detected? YS >> Refer to -91, "iagnosis rocedure". >> ISTI iagnosis rocedure T detection condition ront air mix door motor (passenger side) R position 95% or more ront air mix door motor (passenger side) R position 5% or less ossible cause II:0000000006275925 ront air mix door motor (passenger side) (R internal circuit is open or shorted) ront air mix door motor (passenger side) installation condition / auto amp. arness and connector (I communication line is open or shorted) II:0000000006275926 1. RT IR IX R TR (SSR SI) UITI SI 1. Turn ignition switch. 2. heck output waveform between front air mix door motor R harness connector and ground with the oscilloscope. + ront air mix door motor R utput waveform onnector Terminal 255 3 round YS >> T 2. >> T 3. 2. ISTTI RT IR IX R TR (SSR SI) heck front air mix door motor (passenger side) is properly installed. Refer to -152, "xploded View". YS >> Replace front air mix door motor (passenger side). Refer to -153, "IR IX R TR : Removal and Installation". SI1453-91

2634, 2635 RT IR IX R TR (SSR SI) < T/IRUIT ISIS > [UTTI IR ITII] >> Repair or replace malfunctioning part. 3. RT IR IX R TR (SSR SI) UITI SI IRUIT 1. Turn ignition switch. 2. isconnect front air mix door motor R and / auto amp. connector. 3. heck continuity between front air mix door motor R harness connector and / auto amp. harness connector. ront air mix door motor R / auto amp. onnector Terminal onnector Terminal ontinuity 255 3 50 16 xisted YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Repair harness or connector. -92

2636, 2637, 2638, 2639, 2654, 2655 RT R TR < T/IRUIT ISIS > [UTTI IR ITII] 2636, 2637, 2638, 2639, 2654, 2655 RT R TR T ogic T TTI I T 2636 2637 2638 2639 2654 2655 Items (SUT-III screen terms) R VT R I R / R I R /1 R I R R I /2 VT R I / R I T IRTI RUR 1.RR T IRTI RUR With SUT-III 1. Turn ignition switch. 2. Select Self iagnostic Result mode of V using SUT-III. 3. heck T. Is T detected? YS >> Refer to -93, "iagnosis rocedure". >> ISTI iagnosis rocedure T detection condition When the malfunctioning door position is detected at VT position When the malfunctioning door position is detected at / position When the malfunctioning door position is detected at T position When the malfunctioning door position is detected at position When the malfunctioning door position is detected at / position When the malfunctioning door position is detected at / position ossible cause II:0000000006275927 ront mode door motor (R internal circuit is open or shorted) ront mode door motor control linkage installation condition / auto amp. arness and connector (I communication line is open or shorted) II:0000000006275928 1. RT R TR UITI SI 1. Turn ignition switch. 2. heck output waveform between front mode door motor harness connector and ground with the oscilloscope. + ront mode door motor onnector Terminal utput waveform 253 3 round YS >> T 2. >> T 3. 2. ISTTI RT R TR TR I heck front mode door motor control linkage is properly installed. Refer to -152, "xploded View". -93 SI1453

2636, 2637, 2638, 2639, 2654, 2655 RT R TR < T/IRUIT ISIS > [UTTI IR ITII] YS >> Replace front mode door motor. Refer to -153, " R TR : Removal and Installation". >> Repair or replace malfunctioning part. 3. RT R TR UITI SI IRUIT 1. Turn ignition switch. 2. isconnect front mode door motor and / auto amp. connector. 3. heck continuity between front mode door motor harness connector and / auto amp. harness connector. ront mode door motor / auto amp. onnector Terminal onnector Terminal ontinuity 253 3 50 16 xisted YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Repair harness or connector. -94

263, 263, 263 IT R TR < T/IRUIT ISIS > [UTTI IR ITII] 263, 263, 263 IT R TR T ogic T TTI I II:0000000006275929 T 263 263 263 Items (SUT-III screen terms) R R I 20 R R I R R I T detection condition When the malfunctioning intake door position is detected at R position When the malfunctioning intake door position is detected at 20% R position When the malfunctioning intake door position is detected at R position ossible cause Intake door motor (R internal circuit is open or shorted) Intake door motor control linkage installation condition / auto amp. arness and connector (I communication line is open or shorted) T IRTI RUR 1.RR T IRTI RUR With SUT-III 1. Turn ignition switch. 2. Select Self iagnostic Result mode of V using SUT-III. 3. heck T. Is T detected? YS >> Refer to -95, "iagnosis rocedure". >> ISTI iagnosis rocedure II:0000000006275930 1. IT R TR UITI SI 1. Turn ignition switch. 2. heck output waveform between intake door motor harness connector and ground with the oscilloscope. onnector + Intake door motor Terminal utput waveform 254 3 round YS >> T 2. >> T 3. 2. ISTTI IT R TR TR I heck intake door motor control linkage is properly installed. Refer to -152, "xploded View". YS >> Replace intake door motor. Refer to -153, "IT R TR : Removal and Installation". >> Repair or replace malfunctioning part. SI1453-95

263, 263, 263 IT R TR < T/IRUIT ISIS > [UTTI IR ITII] 3. IT R TR UITI SI IRUIT 1. Turn ignition switch. 2. isconnect intake door motor and / auto amp. connector. 3. heck continuity between intake door motor harness connector and / auto amp. harness connector. Intake door motor / auto amp. onnector Terminal onnector Terminal ontinuity 254 3 50 16 xisted YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Repair harness or connector. -96

2661, 2662, 2663 UR VTITR R TR < T/IRUIT ISIS > [UTTI IR ITII] 2661, 2662, 2663 UR VTITR R TR T ogic T TTI I T 2661 2662 2663 Items (SUT-III screen terms) UR VT R T T IRTI RUR 1.RR T IRTI RUR With SUT-III 1. Turn ignition switch. 2. Select Self iagnostic Result mode of V using SUT-III. 3. heck T. Is T detected? YS >> Refer to -97, "iagnosis rocedure". >> ISTI iagnosis rocedure T detection condition When the malfunctioning upper ventilator door position is detected at position When the malfunctioning upper ventilator door position is detected at middle position When the malfunctioning upper ventilator door position is detected at shut position ossible cause II:0000000006275931 Upper ventilator door motor (R internal circuit is open or shorted) Upper ventilator door motor installation condition / auto amp. arness and connector (I communication line is open or shorted) II:0000000006275932 1. UR VTITR R TR UITI SI 1. Turn ignition switch. 2. heck output waveform between upper vent door motor harness connector and ground with the oscilloscope. + Upper vent door motor utput waveform onnector Terminal 256 3 round YS >> T 2. >> T 3. 2. ISTTI UR VTITR R TR heck upper ventilator door motor is properly installed. Refer to -152, "xploded View". YS >> Replace upper ventilator door motor. Refer to -154, "UR VTITR R TR : Removal and Installation". SI1453-97

2661, 2662, 2663 UR VTITR R TR < T/IRUIT ISIS > [UTTI IR ITII] >> Repair or replace malfunctioning part. 3. UR VTITR R TR UITI SI IRUIT 1. Turn ignition switch. 2. isconnect upper vent door motor and / auto amp. connector. 3. heck continuity between upper vent door motor harness connector and / auto amp. harness connector. Upper vent door motor / auto amp. onnector Terminal onnector Terminal ontinuity 256 3 50 16 xisted YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Repair harness or connector. -98

2664, 2665 RR IR IX R TR < T/IRUIT ISIS > [UTTI IR ITII] 2664, 2665 RR IR IX R TR T ogic T TTI I II:0000000006275933 T 2664 2665 Items (SUT-III screen terms) RR IR IX R T T detection condition Rear air mix door motor R position 95% or more Rear air mix door motor R position 5% or less ossible cause Rear air mix door motor (R internal circuit is open or shorted) Rear air mix door motor installation condition / auto amp. arness and connector (I communication line is open or shorted) T IRTI RUR 1.RR T IRTI RUR With SUT-III 1. Turn ignition switch. 2. Select Self iagnostic Result mode of V using SUT-III. 3. heck T. Is T detected? YS >> Refer to -99, "iagnosis rocedure". >> ISTI iagnosis rocedure II:0000000006275934 1. RR IR IX R TR UITI SI 1. Turn ignition switch. 2. heck output waveform between rear air mix door motor harness connector and ground with the oscilloscope. + Rear air mix door motor utput waveform onnector Terminal 210 3 round YS >> T 2. >> T 3. 2. ISTTI RR IR IX R TR heck rear air mix door motor is properly installed. Refer to -152, "xploded View". YS >> Replace rear air mix door motor. Refer to -154, "RR IR IX R TR : Removal and Installation". >> Repair or replace malfunctioning part. SI1453-99

2664, 2665 RR IR IX R TR < T/IRUIT ISIS > [UTTI IR ITII] 3. RR IR IX R TR UITI SI IRUIT 1. Turn ignition switch. 2. isconnect rear air mix door motor and / auto amp. connector. 3. heck continuity between rear air mix door motor harness connector and / auto amp. harness connector. Rear air mix door motor / auto amp. onnector Terminal onnector Terminal ontinuity 210 3 50 16 xisted YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Repair harness or connector. -100

2666, 2669, 266 RR R TR < T/IRUIT ISIS > [UTTI IR ITII] 2666, 2669, 266 RR R TR T ogic T TTI I II:0000000006275935 T 2666 2669 266 Items (SUT-III screen terms) RR R T T detection condition When the malfunctioning door position is detected at VT position When the malfunctioning door position is detected at / position When the malfunctioning door position is detected at T position ossible cause Rear mode door motor (R internal circuit is open or shorted) Rear mode door motor control linkage installation condition / auto amp. arness and connector (I communication line is open or shorted) T IRTI RUR 1.RR T IRTI RUR With SUT-III 1. Turn ignition switch. 2. Select Self iagnostic Result mode of V using SUT-III. 3. heck T. Is T detected? YS >> Refer to -101, "iagnosis rocedure". >> ISTI iagnosis rocedure II:0000000006275936 1. RR R TR UITI SI 1. Turn ignition switch. 2. heck output waveform between rear mode door motor harness connector and ground with the oscilloscope. + Rear mode door motor utput waveform onnector Terminal 209 3 round YS >> T 2. >> T 3. 2. ISTTI RR R TR TR I heck rear mode door motor control linkage is properly installed. Refer to -152, "xploded View". YS >> Replace rear mode door motor. Refer to -154, "RR R TR : Removal and Installation". >> Repair or replace malfunctioning part. SI1453-101

2666, 2669, 266 RR R TR < T/IRUIT ISIS > [UTTI IR ITII] 3. RR R TR UITI SI IRUIT 1. Turn ignition switch. 2. isconnect rear mode door motor and / auto amp. connector. 3. heck continuity between rear mode door motor harness connector and / auto amp. harness connector. Rear mode door motor / auto amp. onnector Terminal onnector Terminal ontinuity 209 3 50 16 xisted YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Repair harness or connector. -102

2667, 2668 SU SSR (SSR SI) < T/IRUIT ISIS > [UTTI IR ITII] 2667, 2668 SU SSR (SSR SI) T ogic II:0000000006275937 T TTI I T: If T is displayed along with T U1000, first perform the trouble diagnosis for T U1000. Refer to - 72, "T ogic". If T is displayed along with T U1010, first perform the trouble diagnosis for T U1010. -73, "T ogic". Sunload sensor may register a malfunction when indoors, at dusk, or at other times when light is insufficient. When performing the diagnosis indoors, use a lamp (60 W or more) that is pointed at the sunload sensor. T 2667 2668 Items (SUT-III screen terms) SS SU SSR T detection condition etected calorie at sunload sensor (passenger side) 2832 W/m 2 (2436 kcal/m 2 h) or more. etected calorie at sunload sensor (passenger side) 64.7 W/m 2 (55.6 kcal/m 2 h) or less. ossible cause Sunload sensor / auto amp. arness or connectors [The sensor circuit (passenger side) is open or shorted.] T IRTI RUR 1.RR T IRTI RUR With SUT-III 1. Turn ignition switch. 2. Select Self iagnostic Result mode of V using SUT-III. 3. heck T. Is T detected? YS >> Refer to -103, "iagnosis rocedure". >> ISTI iagnosis rocedure 1. SU SSR WR SUY 1. Turn ignition switch. 2. isconnect sunload sensor connector. 3. Turn ignition switch. 4. heck voltage between sunload sensor harness connector and ground. II:0000000006275938 onnector + Sunload sensor Terminal YS >> T 2. >> T 4. 2. SU SSR RU IRUIT Voltage (pprox.) 74 1 round 5 V 1. Turn ignition switch. 2. isconnect / auto amp. connector. 3. heck continuity between sunload sensor harness connector and / auto amp. harness connector. Sunload sensor onnector Terminal ontinuity 74 3 round xisted -103

2667, 2668 SU SSR (SSR SI) < T/IRUIT ISIS > [UTTI IR ITII] YS >> T 3. >> Repair harness or connector. 3. SU SSR heck sunload sensor. Refer to -104, "omponent Inspection". YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Replace sunload sensor. Refer to -149, "Removal and Installation". 4. SU SSR WR SUY IRUIT R 1. Turn ignition switch. 2. isconnect / auto amp. connector. 3. heck continuity between sunload sensor harness connector and / auto amp. harness connector. Sunload sensor / auto amp. onnector Terminal onnector Terminal 74 1 50 29 xisted YS >> T 5. >> Repair harness or connector. 5. SU SSR WR SUY IRUIT R RU SRT heck continuity between sunload sensor harness connector and ground. ontinuity onnector Sunload sensor Terminal ontinuity 74 1 round ot existed YS >> T 6. >> Repair harness or connector. 6. SU SSR WR SUY IRUIT R WR SRT 1. Turn ignition switch. 2. heck voltage between sunload sensor harness connector and ground. onnector YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Repair harness or connector. omponent Inspection + Sunload sensor Terminal Voltage (pprox.) 74 1 round 0 V II:0000000006275939 1. SU SSR 1. Turn ignition switch. 2. Reconnect sunload sensor connector and / auto amp. connector. 3. Turn ignition switch. 4. heck input voltage from sunload sensor between / auto amp. harness connector and ground. Refer to applicable table for normal value. -104

2667, 2668 SU SSR (SSR SI) < T/IRUIT ISIS > [UTTI IR ITII] + / auto amp. onnector Terminal 50 29 round II1659 T: When checking indoors, use a lamp of approximately 60 W. ove the lamp towards and away from the sensor to check. The sunload amount produced by direct sunshine in fair weather is equivalent to approximately 0.770 kw/m 2 (662 kcal/m 2 h). YS >> ISTI >> Replace sunload sensor. Refer to -149, "Removal and Installation". -105

266, 266 RR I-VI SSR < T/IRUIT ISIS > [UTTI IR ITII] 266, 266 RR I-VI SSR T ogic II:0000000006275940 T TTI I T: If T is displayed along with T U1000, first perform the trouble diagnosis for T U1000. Refer to - 72, "T ogic". If T is displayed along with T U1010, first perform the trouble diagnosis for T U1010. -73, "T ogic". T Items (SUT-III screen terms) T detection condition ossible cause 266 266 RR I-VI S The rear in-vehicle sensor recognition temperature is too high. The rear in-vehicle sensor recognition temperature is too low. Rear in-vehicle sensor / auto amp. arness or connectors (The sensor circuit is open or shorted.) T IRTI RUR 1.RR T IRTI RUR With SUT-III 1. Turn ignition switch. 2. Select Self iagnostic Result mode of V using SUT-III. 3. heck T. Is T detected? YS >> Refer to -106, "iagnosis rocedure". >> ISTI iagnosis rocedure II:0000000006275941 1. RR I-VI SSR WR SUY 1. Turn ignition switch. 2. isconnect rear in-vehicle sensor connector. 3. Turn ignition switch. 4. heck voltage between rear in-vehicle sensor harness connector and ground. + Rear in-vehicle sensor onnector Terminal 211 1 round 5 V YS >> T 2. >> T 4. 2. RR I-V SSR RU IRUIT 1. Turn ignition switch. 2. isconnect / auto amp. connector. 3. heck continuity between rear in-vehicle sensor harness connector and ground. Voltage (pprox.) Rear in-vehicle sensor onnector Terminal ontinuity 211 2 round xisted -106

266, 266 RR I-VI SSR < T/IRUIT ISIS > [UTTI IR ITII] YS >> T 3. >> Repair harness or connector. 3. RR I-VI SSR heck rear in-vehicle sensor. Refer to -107, "omponent Inspection". YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Replace rear in-vehicle sensor. Refer to -148, "RR / UIT SSY : Removal and Installation". 4. RR I-V SSR WR SUY IRUIT R 1. Turn ignition switch. 2. isconnect / auto amp. connector. 3. heck continuity between rear in-vehicle sensor harness connector and / auto amp. harness connector. Rear in-vehicle sensor / auto amp. onnector Terminal onnector Terminal 211 1 50 8 xisted YS >> T 5. >> Repair harness or connector. 5. RR I-V SSR WR SUY IRUIT R RU SRT heck continuity between rear in-vehicle sensor harness connector and ground. Rear in-vehicle sensor onnector Terminal ontinuity ontinuity 211 1 round ot existed YS >> T 6. >> Repair harness or connector. 6. RR I-VI SSR WR SUY IRUIT R WR SRT 1. Turn ignition switch. 2. heck voltage between rear in-vehicle sensor harness connector and ground. YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Repair harness or connector. omponent Inspection + Rear in-vehicle sensor onnector Terminal 1. RR I-VI SSR 1. Turn ignition switch. 2. isconnect rear in-vehicle sensor connector. 3. heck resistance between rear in-vehicle sensor terminals. Voltage (pprox.) 211 1 round 0 V II:0000000006275942-107

266, 266 RR I-VI SSR < T/IRUIT ISIS > [UTTI IR ITII] Terminal 1 2 ondition Temperature: ( ) Resistance: kω 15 (5) 12.34 10 (14) 9.62 5 (23) 7.56 0 (32) 6.00 5 (41) 4.80 10 (50) 3.87 15 (59) 3.14 20 (68) 2.57 25 (77) 2.12 30 (86) 1.76 35 (95) 1.47 40 (104) 1.23 45 (113) 1.04 YS >> ISTI >> Replace rear in-vehicle sensor. Refer to -148, "RR / UIT SSY : Removal and Installation". -108

270 / UT. < T/IRUIT ISIS > [UTTI IR ITII] 270 / UT. T ogic II:0000000006275946 T TTI I T: If T is displayed along with T U1000, first perform the trouble diagnosis for T U1000. Refer to - 72, "T ogic". If T is displayed along with T U1010, first perform the trouble diagnosis for T U1010. -73, "T ogic". T Items (SUT-III screen terms) T detection condition ossible cause 270 / UT. / auto amp. R system is malfunctioning. / auto amp. T IRTI RUR 1.RR T IRTI RUR With SUT-III 1. Turn ignition switch. 2. Select Self iagnostic Result mode of V using SUT-III. 3. heck T. Is T detected? YS >> Refer to -109, "iagnosis rocedure". >> ISTI iagnosis rocedure 1.RR S ISTI With SUT-III 1. Turn ignition switch. 2. Select Self iagnostic Result mode of V using SUT-III. 3. Touch RS. 4. Turn ignition switch. 5. Turn ignition switch. 6. erform T IRTI RUR. Refer to -109, "T ogic". Is T detected again? YS >> Replace / auto amp. Refer to -146, "Removal and Installation". >> ISTI II:0000000006275947-109

WR SUY RU IRUIT < T/IRUIT ISIS > [UTTI IR ITII] WR SUY RU IRUIT / UT. / UT. : iagnosis rocedure 1. US heck 10 fuse [o. 9, 19, and 4, located in the fuse block (/)]. T: Refer to -140, "use, onnector and Terminal rrangement". YS >> T 2. >> Replace the blown fuse after repairing the affected circuit if a fuse is blown. 2. / UT. WR SUY 1. Turn ignition switch. 2. isconnect / auto amp. connector. 3. heck voltage between / auto amp. harness connector and ground. II:0000000006275948 + / auto amp. YS >> T 3. >> Repair harness or connector between / auto amp. and fuse block (/). 3. / UT. RU IRUIT 1. Turn ignition switch. 2. heck continuity between / auto amp. harness connector and ground. Voltage Ignition switch position onnector Terminal 50 4 pprox. 0 V attery voltage attery voltage 23 round pprox. 0 V pprox. 0 V attery voltage 3 attery voltage attery voltage attery voltage / auto amp. onnector Terminal ontinuity 50 2 22 37 round xisted YS >> ISTI >> Repair harness or connector. RT IR IX R TR (RIVR SI) RT IR IX R TR (RIVR SI) : iagnosis rocedure II:0000000006275949 1. RT IR IX R TR (RIVR SI) WR SUY 1. Turn ignition switch. 2. heck voltage between front air mix door motor harness connector and ground. -110

WR SUY RU IRUIT < T/IRUIT ISIS > [UTTI IR ITII] + ront air mix door motor onnector Terminal YS >> T 2. >> T 4. 2. RT IR IX R TR (RIVR SI) RU IRUIT 1. Turn ignition switch. 2. isconnect front air mix door motor connector. 3. heck continuity between front air mix door motor harness connector and ground. YS >> T 3. >> Repair harness or connector. 3. ISTTI RT IR IX R TR (RIVR SI) Voltage (pprox.) 252 1 round 12 V ront air mix door motor onnector Terminal ontinuity 252 2 round xisted heck front air mix door motor (driver side) is properly installed. Refer to -152, "xploded View". YS >> Replace front air mix door motor (driver side). Refer to -153, "IR IX R TR : Removal and Installation". >> Repair or replace malfunctioning part. 4. RT IR IX R TR (RIVR SI) WR SUY IRUIT 1. Turn ignition switch. 2. isconnect front air mix door motor connector and / auto amp. connector. 3. heck continuity between front air mix door motor harness connector and / auto amp. harness connector. ront air mix door motor / auto amp. onnector Terminal onnector Terminal 252 1 50 17 xisted YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Repair harness or connector. RT IR IX R TR (SSR SI) ontinuity RT IR IX R TR (SSR SI) : iagnosis rocedure 1. RT IR IX R TR (SSR SI) WR SUY 1. Turn ignition switch. 2. heck voltage between front air mix door motor R harness connector and ground. II:0000000006275950 + ront air mix door motor R onnector Terminal -111 Voltage (pprox.) 255 1 round 12 V

WR SUY RU IRUIT < T/IRUIT ISIS > [UTTI IR ITII] YS >> T 2. >> T 4. 2. RT IR IX R TR (SSR SI) RU IRUIT 1. Turn ignition switch. 2. isconnect front air mix door motor R connector. 3. heck continuity between front air mix door motor R harness connector and ground. ront air mix door motor R onnector Terminal ontinuity 255 2 round xisted YS >> T 3. >> Repair harness or connector. 3. ISTTI RT IR IX R TR (SSR SI) heck front air mix door motor (passenger side) is properly installed. Refer to -152, "xploded View". YS >> Replace front air mix door motor (passenger side). Refer to -153, "IR IX R TR : Removal and Installation". >> Repair or replace malfunctioning part. 4. RT IR IX R TR (SSR SI) WR SUY IRUIT 1. Turn ignition switch. 2. isconnect front air mix door motor R connector and / auto amp. connector. 3. heck continuity between front air mix door motor R harness connector and / auto amp. harness connector. ront air mix door motor R / auto amp. ontinuity onnector Terminal onnector Terminal 255 1 50 17 xisted YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Repair harness or connector. RT R TR RT R TR : iagnosis rocedure II:0000000006275951 1. RT R TR WR SUY 1. Turn ignition switch. 2. heck voltage between front mode door motor harness connector and ground. + ront mode door motor onnector Terminal YS >> T 2. >> T 4. 2. RT R TR RU IRUIT 1. Turn ignition switch. 2. isconnect front mode door motor connector. -112 Voltage (pprox.) 253 1 round 12 V

WR SUY RU IRUIT < T/IRUIT ISIS > [UTTI IR ITII] 3. heck continuity between front mode door motor harness connector and ground. ront mode door motor onnector Terminal ontinuity 253 2 round xisted YS >> T 3. >> Repair harness or connector. 3. ISTTI RT R TR TR I heck front mode door motor control linkage is properly installed. Refer to -152, "xploded View". YS >> Replace front mode door motor. Refer to -153, " R TR : Removal and Installation". >> Repair or replace malfunctioning part. 4. RT R TR WR SUY IRUIT 1. Turn ignition switch. 2. isconnect front mode door motor connector and / auto amp. connector. 3. heck continuity between front mode door motor harness connector and / auto amp. harness connector. ront mode door motor 253 1 50 17 xisted YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Repair harness or connector. IT R TR / auto amp. onnector Terminal onnector Terminal IT R TR : iagnosis rocedure 1. IT R TR WR SUY ontinuity 1. Turn ignition switch. 2. heck voltage between intake mode door motor harness connector and ground. II:0000000006275952 + Intake mode door motor onnector Terminal YS >> T 2. >> T 4. 2. IT R TR RU IRUIT 1. Turn ignition switch. 2. isconnect intake mode door motor connector. 3. heck continuity between intake mode door motor harness connector and ground. Voltage (pprox.) 254 1 round 12 V Intake mode door motor onnector Terminal ontinuity 254 2 round xisted -113

WR SUY RU IRUIT < T/IRUIT ISIS > [UTTI IR ITII] YS >> T 3. >> Repair harness or connector. 3. ISTTI IT R TR TR I heck intake mode door motor control linkage is properly installed. Refer to -152, "xploded View". YS >> Replace intake mode door motor. Refer to -153, "IT R TR : Removal and Installation". >> Repair or replace malfunctioning part. 4. IT R TR WR SUY IRUIT 1. Turn ignition switch. 2. isconnect intake mode door motor connector and / auto amp. connector. 3. heck continuity between intake mode door motor harness connector and / auto amp. harness connector. Intake mode door motor / auto amp. ontinuity onnector Terminal onnector Terminal 254 1 50 17 xisted YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Repair harness or connector. RR IR IX R TR RR IR IX R TR : iagnosis rocedure II:0000000006275953 1. RR IR IX R TR WR SUY 1. Turn ignition switch. 2. heck voltage between rear air mix door motor harness connector and ground. + Rear air mix door motor onnector Terminal YS >> T 2. >> T 4. 2. RR IR IX R TR RU IRUIT 1. Turn ignition switch. 2. isconnect rear air mix door motor connector. 3. heck continuity between rear air mix door motor harness connector and ground. Voltage (pprox.) 210 1 round 12 V Rear air mix door motor onnector Terminal ontinuity 210 2 round xisted YS >> T 3. >> Repair harness or connector. 3. ISTTI RR IR IX R TR heck rear air mix door motor is properly installed. Refer to -152, "xploded View". -114

WR SUY RU IRUIT < T/IRUIT ISIS > [UTTI IR ITII] YS >> Replace rear air mix door motor. Refer to -154, "RR IR IX R TR : Removal and Installation". >> Repair or replace malfunctioning part. 4. RR IR IX R TR WR SUY IRUIT 1. Turn ignition switch. 2. isconnect rear air mix door motor connector and / auto amp. connector. 3. heck continuity between rear air mix door motor harness connector and / auto amp. harness connector. Rear air mix door motor 210 1 50 17 xisted YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Repair harness or connector. RR / TR RR / TR : iagnosis rocedure 1. US / auto amp. onnector Terminal onnector Terminal heck 10 fuse [o. 4, located in the fuse block (/)]. T: Refer to -140, "use, onnector and Terminal rrangement". YS >> T 2. >> Replace the blown fuse after repairing the affected circuit if a fuse is blown. 2. RR / TR WR SUY 1. Turn ignition switch. 2. isconnect rear / control connector. 3. Turn ignition switch. 4. heck voltage between rear / control harness connector and ground. ontinuity II:0000000006275954 onnector + 41 12 round attery voltage YS >> T 3. >> Repair harness or connector between rear / control and fuse block (/). 3. RR / TR RU IRUIT 1. Turn ignition switch. 2. heck continuity between rear / control harness connector and ground. onnector Rear / control Rear / control Terminal Terminal 41 1 round xisted YS >> Replace rear / control. Refer to -146, "Removal and Installation". >> Repair harness or connector. Voltage ontinuity -115

WR SUY RU IRUIT < T/IRUIT ISIS > [UTTI IR ITII] RR R TR RR R TR : iagnosis rocedure 1. RR R TR WR SUY 1. Turn ignition switch. 2. heck voltage between rear mode door motor harness connector and ground. II:0000000006275955 + Rear mode door motor onnector Terminal YS >> T 2. >> T 4. 2. RR R TR RU IRUIT 1. Turn ignition switch. 2. isconnect rear mode door motor connector. 3. heck continuity between rear mode door motor harness connector and ground. Voltage (pprox.) 209 1 round 12 V Rear mode door motor onnector Terminal ontinuity 209 2 round xisted YS >> T 3. >> Repair harness or connector. 3. ISTTI RR R TR TR I heck rear mode door motor control linkage is properly installed. Refer to -152, "xploded View". YS >> Replace rear mode door motor. Refer to -154, "RR R TR : Removal and Installation". >> Repair or replace malfunctioning part. 4. RR R TR WR SUY IRUIT 1. Turn ignition switch. 2. isconnect rear mode door motor connector and / auto amp. connector. 3. heck continuity between rear mode door motor harness connector and / auto amp. harness connector. Rear mode door motor / auto amp. ontinuity onnector Terminal onnector Terminal 209 1 50 17 xisted YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Repair harness or connector. UR VTITR R TR UR VTITR R TR : iagnosis rocedure II:0000000006275956 1. UR VTITR R TR WR SUY 1. Turn ignition switch. -116

WR SUY RU IRUIT < T/IRUIT ISIS > [UTTI IR ITII] 2. heck voltage between upper ventilator door motor harness connector and ground. + Upper ventilator door motor onnector Terminal YS >> T 2. >> T 4. 2. UR VTITR R TR RU IRUIT 1. Turn ignition switch. 2. isconnect upper ventilator door motor connector. 3. heck continuity between upper ventilator door motor harness connector and ground. Voltage (pprox.) 256 1 round 12 V Upper ventilator door motor onnector Terminal ontinuity 256 2 round xisted YS >> T 3. >> Repair harness or connector. 3. ISTTI UR VTITR R TR heck upper ventilator door motor is properly installed. Refer to -152, "xploded View". YS >> Replace upper ventilator door motor. Refer to -154, "UR VTITR R TR : Removal and Installation". >> Repair or replace malfunctioning part. 4. UR VTITR R TR WR SUY IRUIT 1. Turn ignition switch. 2. isconnect upper ventilator door motor connector and / auto amp. connector. 3. heck continuity between upper ventilator door motor harness connector and / auto amp. harness connector. Upper ventilator door motor / auto amp. onnector Terminal onnector Terminal ontinuity 256 1 50 17 xisted YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Repair harness or connector. -117

R TR < T/IRUIT ISIS > [UTTI IR ITII] R TR iagnosis rocedure 1. R TR WR SUY 1. Turn ignition switch. 2. heck voltage between intake door motor harness connector and ground. II:0000000006275966 onnector + Intake door motor Terminal YS >> T 2. >> T 3. 2. R TR RU IRUIT 1. Turn ignition switch. 2. isconnect intake door motor connector. 3. heck continuity between intake door motor harness connector and ground. Voltage (pprox.) 254 1 round 12 V onnector Intake door motor Terminal ontinuity 254 2 round xisted YS >> ISTI >> Repair harness or connector. 3. R TR WR SUY IRUIT R 1. isconnect / auto amp. connector. 2. heck continuity between intake door motor harness connector and / auto amp. harness connector. Intake door motor / auto amp. onnector Terminal onnector Terminal 254 1 50 17 xisted YS >> T 4. >> Repair harness or connector. 4. R TR WR SUY IRUIT R SRT 1. isconnect following connectors. - ront air mix door motor - ront air mix door motor R - ront mode door motor - Upper vent door motor - Rear air mix door motor - Rear mode door motor 2. heck continuity between intake door motor harness connector and ground. ontinuity Intake door motor onnector Terminal ontinuity 254 1 round ot existed -118

R TR < T/IRUIT ISIS > [UTTI IR ITII] YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Repair harness or connector. -119

R TR UITI IRUIT < T/IRUIT ISIS > [UTTI IR ITII] R TR UITI IRUIT iagnosis rocedure T: If all of door motor Ts are detected, check this circuit. 1. R TR UITI SI II:0000000006275967 1. Turn ignition switch. 2. heck output waveform between / auto amp. harness connector and ground with the oscilloscope. + / auto amp. onnector Terminal utput waveform 50 16 round YS >> T 2. >> T 3. 2. R TR UITI SI IRUIT R 1. Turn ignition switch. 2. isconnect / auto amp. connector and intake door motor connector. 3. heck continuity between / auto amp. harness connector and intake door motor harness connector. SI1453 / auto amp. Intake door motor onnector Terminal onnector Terminal ontinuity 50 16 254 3 xisted YS >> ISTI >> Repair harness or connector. 3. R TR UITI SI IRUIT R SRT 1. isconnect following connectors. - ront air mix door motor - ront air mix door motor R - ront mode door motor - Upper vent door motor - Rear air mix door motor - Rear mode door motor 2. heck continuity between / auto amp. harness connector and ground. / auto amp. onnector Terminal ontinuity 50 16 round ot existed YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Repair harness or connector. -120

RT WR TR < T/IRUIT ISIS > [UTTI IR ITII] RT WR TR iagnosis rocedure 1. US 1. Turn ignition switch. 2. heck 15 fuse [o. 21 and 22, located in fuse block (/)]. T: Refer to -140, "use, onnector and Terminal rrangement". YS >> T 2. >> Replace the blown fuse after repairing the affected circuit if a fuse is blown. 2. RT WR TR WR SUY 1. isconnect front blower motor connector. 2. Turn ignition switch. 3. heck voltage between front blower motor harness connector and ground. + ront blower motor onnector Terminal YS >> T 3. >> T 6. 3. RT WR TR RU IRUIT 1. Turn ignition switch. 2. heck continuity between front blower motor harness connector and ground. YS >> T 4. >> Repair harness or connector. 4. RT WR TR TR SI IRUIT -121 II:0000000006275968 1. isconnect / auto amp. connector. 2. heck continuity between front blower motor harness connector and / auto amp. harness connector. 272 2 50 14 xisted YS >> T 5. >> Repair the harness or connector. 5. RT WR TR TR SI Voltage 272 1 round attery voltage ront blower motor onnector Terminal ontinuity 272 3 round xisted ront blower motor / auto amp. onnector Terminal onnector Terminal ontinuity 1. Reconnect front blower motor connector and / auto amp. connector. 2. Turn ignition switch. 3. perate switch to set air outlet to VT. 4. hange fan speed from o to i, and check duty ratios between front blower motor harness connector and ground by using an oscilloscope.

RT WR TR < T/IRUIT ISIS > [UTTI IR ITII] T: alculate drive signal duty ratio as shown in the figure. T2 = pprox. 1.6 ms onnector ront blower motor Terminal 272 2 ondition an speed (manual) VT mode uty ratio (pprox.) 1st 25 % 2nd 33 % 3rd 41 % 4th 51 % 5th 61 % 6th 69 % 7th 81 % YS >> Replace front blower motor. Refer to VT-16, "RT / UIT : Removal and Installation". >> Replace / auto amp.. Refer to -146, "Removal and Installation". 6. WR RY RU IRUIT heck continuity between fuse block (/) harness connector and ground. I1210 use block (/) onnector Terminal 3 7 round xisted YS >> T 7. >> Repair harness or connector. 7. WR RY heck blower relay. Refer to -123, "omponent Inspection (lower Relay)". YS >> Repair harness or connector between front blower motor and fuse block (/). >> Replace blower relay. omponent Inspection (ront lower otor) ontinuity II:0000000006275969 1. RT WR TR-I 1. Remove front blower motor. 2. heck that there is not any mixing foreign object in the front blower motor. YS >> T 2. >> Replace front blower motor. Refer to VT-16, "RT / UIT : Removal and Installation". 2. RT WR TR-II heck that there is not breakage or damage in the front blower motor. YS >> T 3. >> Replace front blower motor. Refer to VT-16, "RT / UIT : Removal and Installation". 3. RT WR TR-III heck that front blower motor turns smoothly. YS >> ISTI -122

RT WR TR < T/IRUIT ISIS > [UTTI IR ITII] >> Replace front blower motor. Refer to VT-16, "RT / UIT : Removal and Installation". omponent Inspection (lower Relay) 1. WR RY 1. Turn ignition switch. 2. Remove blower relay. 3. heck continuity between blower relay terminal 3 and 5 when voltage is supplied between terminal 1 and 2. II:0000000006275970 Terminal Voltage ontinuity 3 5 xisted ot existed YS >> ISTI >> Replace blower relay. SII1551ZZ -123

IIZR < T/IRUIT ISIS > [UTTI IR ITII] IIZR omponent unction heck 1. IIZR RTI SU II:0000000006275971 1. Turn ignition switch. 2. heck ionizer operation sound (whirring sound) in duct by putting an ear to the side ventilator grille (driver side) outlet while pressing fan switch and switch alternately. YS >> ISTI >> Refer to -124, "iagnosis rocedure". iagnosis rocedure 1. US 1. Turn ignition switch. 2. heck 10 fuse [o.4, located in fuse block (/)]. T: Refer to -140, "use, onnector and Terminal rrangement". YS >> T 2. >> Replace the blown fuse after repairing the affected circuit if a fuse is blown. 2. IIZR WR SUY 1. isconnect ionizer connector. 2. Turn ignition switch. 3. heck voltage between ionizer harness connector and ground. II:0000000006275972 onnector + Ionizer Terminal YS >> T 3. >> Repair harness or connector between ionizer and fuse block (/). 3. IIZR RU IRUIT 1. Turn ignition switch. 2. heck continuity between ionizer harness connector and ground. Voltage 130 1 round attery voltage onnector Ionizer Terminal ontinuity 130 3 round xisted YS >> T 4. >> Repair harness or connector. 4. IIZR (/) TR SI IRUIT 1. onnect ionizer connector. 2. isconnect / auto amp. connector. 3. Turn ignition switch. 4. heck voltage between / auto amp. harness connector and ground. -124

IIZR < T/IRUIT ISIS > [UTTI IR ITII] onnector + / auto amp. Terminal YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> T 5. 5. IIZR (/) TR SI IRUIT R 1. Turn ignition switch. 2. isconnect ionizer connector. 3. heck continuity between / auto amp. harness connector and ionizer harness connector. 50 5 130 4 xisted YS >> T 6. >> Repair harness or connector. 6. IIZR (/) TR SI IRUIT R SRT heck continuity between / auto amp. harness connector and ground. Voltage 50 5 round attery voltage / auto amp. Ionizer onnector Terminal onnector Terminal ontinuity / auto amp. onnector Terminal ontinuity 50 5 round ot existed YS >> Replace ionizer. Refer to -155, "Removal and Installation". >> Repair harness or connector. -125

T UT < T/IRUIT ISIS > [UTTI IR ITII] T UT omponent unction heck II:0000000006275973 1. T UT RTI erform auto active test of I /R. Refer to S-10, "iagnosis escription". oes it operate normally? YS >> ISTI >> Refer to -126, "iagnosis rocedure". iagnosis rocedure II:0000000006275974 1. US 1. Turn ignition switch. 2. heck 10 fuse (o. 49, located in I /R). T: Refer to -140, "use, onnector and Terminal rrangement". YS >> T 2. >> Replace the blown fuse after repairing the affected circuit if a fuse is blown. 2. T UT WR SUY IRUIT 1. isconnect compressor connector and I /R connector. 2. heck continuity between compressor harness connector and I /R harness connector. ompressor YS >> T 3. >> Repair harness or connector. 3. T UT I /R onnector Terminal onnector Terminal ontinuity 43 1 15 56 xisted irectly apply battery voltage to the magnet clutch. heck operation visually and by sound. oes it operate normally? YS >> Replace I /R. Refer to S-32, "Removal and Installation". >> Replace magnet clutch. Refer to -31, "T UT : Removal and Installation of ompressor lutch". -126

RR / TR UITI SI < T/IRUIT ISIS > [UTTI IR ITII] RR / TR UITI SI iagnosis rocedure II:0000000006275975 1. UITI SI IRUIT (/ UT. RR / TR) R 1. Turn ignition switch. 2. isconnect rear / control and / auto amp. connector. 3. heck continuity between rear / control harness connector and / auto amp. harness connector. Rear / control / auto amp. onnector Terminal onnector Terminal 41 9 50 11 xisted YS >> T 2. >> Repair harness or connector. 2. UITI SI IRUIT (/ UT. RR / TR) R SRT heck continuity between rear / control harness connector and ground. onnector Rear / control Terminal ontinuity ontinuity 41 9 round ot existed YS >> T 3. >> Repair harness or connector. 3. UITI SI IRUIT (RR / TR / UT.) IRUIT R heck continuity between rear / control harness connector and / auto amp. harness connector. Rear / control / auto amp. onnector Terminal onnector Terminal ontinuity 41 10 50 31 xisted YS >> T 4. >> Repair harness or connector. 4. UITI SI IRUIT (RR / TR / UT.) IRUIT R SRT heck continuity between rear / control harness connector and ground. onnector Rear / control Terminal ontinuity 41 10 round ot existed YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Repair harness or connector. -127

RR / SI VV < T/IRUIT ISIS > [UTTI IR ITII] RR / SI VV iagnosis rocedure 1. US 1. Turn ignition switch. 2. heck 10 fuse [o.4, located in fuse block (/)]. T: Refer to -140, "use, onnector and Terminal rrangement". YS >> T 2. >> Replace the blown fuse after repairing the affected circuit if a fuse is blown. 2. RR / SI VV WR SUY II:0000000006275976 1. isconnect rear / solenoid valve connector. 2. Turn ignition switch and front air conditioning system. 3. heck voltage between rear / solenoid valve harness connector and ground when rear blower motor is operated. + Rear / solenoid valve onnector Terminal 207 1 round Rear blower motor YS >> T 3. >> T 4. 3. RR / SI VV RU IRUIT 1. Turn ignition switch. 2. heck continuity between rear / solenoid valve harness connector and ground. ondition Voltage (pprox.) attery voltage 0 V onnector Rear / solenoid valve Terminal YS >> Replace rear expansion valve assembly. Refer to -49, "XSI VV : Removal and Installation". >> Repair harness or connector. 4. RR / RY WR SUY ontinuity 207 2 round xisted 1. Turn ignition switch. 2. isconnect rear / relay connector. 3. Turn ignition switch. 4. heck voltage between rear / relay harness connector and ground. onnector + Rear / relay Terminal Voltage (pprox.) 87 1 3 round attery voltage YS >> T 5. -128

RR / SI VV < T/IRUIT ISIS > [UTTI IR ITII] >> Repair harness or connector between rear / relay and fuse block (/). 5. RR / RRY TR IRUIT R 1. Turn ignition switch. 2. isconnect / auto amp. connector. 3. heck continuity between rear / relay harness connector and / auto amp. harness connector. Rear / relay / auto amp. onnector Terminal onnector Terminal 87 2 50 38 xisted YS >> T 6. >> Repair harness or connector. 6. RR / RY TR IRUIT R SRT heck continuity between rear / relay harness connector and ground. onnector Rear / relay Terminal YS >> T 7. >> Repair harness or connector. 7. RR / SI VV WR SUY IRUIT ontinuity ontinuity 87 2 round ot existed heck continuity between rear / relay harness connector and rear / solenoid valve harness connector. Rear / relay 87 5 207 1 xisted YS >> T 8. >> Repair harness or connector. 8. RR / RY heck rear / relay. Refer to -129, "omponent Inspection". YS >> Replace / auto amp.. Refer to -146, "Removal and Installation". >> Replace rear / relay. omponent Inspection 1. RR / RY 1. Remove rear / relay. Rear / solenoid valve onnector Terminal onnector Terminal ontinuity II:0000000006275977-129

RR / SI VV < T/IRUIT ISIS > [UTTI IR ITII] 2. heck continuity between the rear / relay terminal 3 and 5 when the voltage is supplied between terminal 1 and 2. lower relay Voltage Terminal 3 5 YS >> ISTI >> Replace rear / relay. ontinuity xisted ot existed SII1551ZZ -130

RR WR TR < T/IRUIT ISIS > [UTTI IR ITII] RR WR TR iagnosis rocedure 1. US 1. Turn ignition switch. 2. heck 20 fuse [o. 16, located in fuse block (/)]. T: Refer to -140, "use, onnector and Terminal rrangement". YS >> T 2. >> Replace the blown fuse after repairing the affected circuit if a fuse is blown. 2. RR WR TR WR SUY 1. Turn ignition switch. 2. isconnect rear blower motor connector. 3. Turn ignition switch. 4. heck voltage between rear blower motor harness connector and ground. II:0000000006275978 onnector + Rear blower motor Terminal YS >> T 3. >> Repair harness or connector between rear blower motor and fuse block (/). 3. RR WR TR RU IRUIT 1. Turn ignition switch. 2. heck continuity between rear blower motor harness connector and ground. Voltage 302 1 round attery voltage onnector Rear blower motor Terminal ontinuity 302 3 round xisted YS >> T 4. >> Repair harness or connector. 4. RR WR TR TR SI IRUIT 1. isconnect / auto amp. connector. 2. heck continuity between rear blower motor harness connector and / auto amp. harness connector. Rear blower motor / auto amp. onnector Terminal onnector Terminal 302 2 50 34 xisted YS >> T 5. >> Repair harness or connector. 5. RR WR TR TR SI 1. Reconnect rear blower motor connector and / auto amp. connector. 2. Turn ignition switch. 3. perate switch to set air outlet to VT. ontinuity -131

RR WR TR < T/IRUIT ISIS > [UTTI IR ITII] 4. hange fan speed from o to i, and check duty ratios between rear blower motor harness connector and ground by using an oscilloscope. T: alculate drive signal duty ratio as shown in the figure. T2 = pprox. 1.6 ms onnector Rear blower motor Terminal 272 2 7th 81 % YS >> Replace rear blower motor. Refer to VT-16, "RR / UIT SSY : Removal and Installation". >> Replace / auto amp.. Refer to -146, "Removal and Installation". omponent Inspection 1. RR WR TR-I ondition an speed (manual) VT mode uty ratio (pprox.) 1st 25 % 2nd 33 % 3rd 41 % 4th 51 % 5th 61 % 6th 69 % I1210 II:0000000006275979 1. Remove rear blower motor. 2. heck that there is not any mixing foreign object in the rear blower motor. YS >> T 2. >> Replace rear blower motor. Refer to VT-16, "RR / UIT SSY : Removal and Installation". 2. RR WR TR-II heck that there is not breakage or damage in the rear blower motor. YS >> T 3. >> Replace rear blower motor. Refer to VT-16, "RR / UIT SSY : Removal and Installation". 3. RR WR TR-III heck that rear blower motor turns smoothly. YS >> ISTI >> Replace rear blower motor. Refer to VT-16, "RR / UIT SSY : Removal and Installation". -132

RT UTTI IR ITII SYST < SYT ISIS > [UTTI IR ITII] SYT ISIS RT UTTI IR ITII SYST iagnosis hart y Symptom II:0000000006275980 T: erform the self-diagnoses with SUT-III before performing the symptom diagnosis. If T is detected, perform the corresponding diagnosis. ront air conditioning system does not activate. ront air conditioning system cannot be controlled. peration status of front air conditioning system is not indicated on front display. Symptom orresponding malfunction part Reference ail-safe activates ulti V system V-199, "Symptom Table" ail-safe does not activate ir outlet does not change (xcept upper ventilation). ront mode door motor does not operate normally. Upper ventilator door does not change. Upper ventilator door motor does not operate normally. ischarge air temperature of driver side does not change. ront air mix door motor (driver side) does not operate normally. ischarge air temperature of passenger side does not change. ront air mix door motor (passenger side) does not operate normally. Intake door does not change. Intake door motor does not operate normally. ll door motors do not operate normally. ront blower motor operation is malfunctioning. ower supply system of / auto amp. / auto amp. ircuit between front mode door motor and / auto amp. ront mode door motor control linkage ront mode door motor / auto amp. ircuit between upper ventilator door motor and / auto amp. Upper ventilator door motor installation condition Upper ventilator door motor / auto amp. ircuit between front air mix door motor (driver side) and / auto amp. ront air mix door motor (driver side) installation condition ront air mix door motor (driver side) / auto amp. ircuit between front air mix door motor (passenger side) and / auto amp. ront air mix door motor (passenger side) installation condition ront air mix door motor (passenger side) / auto amp. ircuit between intake door motor and / auto amp. Intake door motor control linkage Intake door motor / auto amp. ach door motor power supply and ground circuit / auto amp. ower supply system of front blower motor ircuit between front blower motor and / auto amp.. ront blower motor / auto amp. -110, "/ UT. : iagnosis rocedure" -112, "RT R TR : iagnosis rocedure" -116, "UR VTITR R TR : iagnosis rocedure" -110, "RT IR IX R TR (RIVR SI) : iagnosis rocedure" -111, "RT IR IX R TR (SSR SI) : iagnosis rocedure" -113, "IT R TR : iagnosis rocedure" -118, "iagnosis rocedure" -121, "iagnosis rocedure" -133

RT UTTI IR ITII SYST < SYT ISIS > [UTTI IR ITII] ompressor does not operate. Insufficient cooling. o cool air comes out. (ir flow volume is normal.) Insufficient heating. o warm air comes out. (ir flow volume is normal.) oise is heard when front air conditioning system operates. uring compressor operation uring front blower motor operation emory function does not operate. Setting temperature is not memorized. Symptom orresponding malfunction part Reference ircuit between magnet clutch and I /R agnet clutch I /R (/ relay) ircuit between and refrigerant pressure sensor Refrigerant pressure sensor communication circuit / auto amp. agnet clutch control system rive belt slipping Refrigerant cycle ir leakage from each duct / auto amp. connection recognition signal circuit Temperature setting trimmer (front) ngine cooling system eater hose eater core ir leakage from each duct Temperature setting trimmer (front) Refrigerant cycle ixing any foreign object in front blower motor ront blower motor fan breakage ront blower motor rotation inferiority attery power supply system of / auto amp. / auto amp. -142, "iagnosis rocedure" -138, "RT IR I- TIR : iagnosis rocedure" -140, "RT IR I- TIR : iagnosis rocedure" -27, "Symptom Table" -122, "omponent Inspection (ront lower otor)" -110, "/ UT. : iagnosis rocedure" -134

RR UTTI IR ITII SYST < SYT ISIS > [UTTI IR ITII] RR UTTI IR ITII SYST iagnosis hart y Symptom II:0000000006275981 T: erform the self-diagnoses with SUT-III before performing the symptom diagnosis. If T is detected, perform the corresponding diagnosis. The following table is based on the condition that front automatic air conditioning system operates normally. Symptom orresponding malfunction part Reference Rear air conditioning system cannot be controlled. (ront / control) peration status of rear air conditioning system is not indicated on front display. Rear air conditioning system cannot be controlled. (Rear / control) peration status of rear air conditioning system is not indicated on rear / control display peration status of rear air conditioning system is indicated on rear / control display ir outlet does not change. Rear mode door motor does not operate normally. ischarge air temperature does not change. Rear air mix door motor does not operate normally. Rear blower motor operation is malfunctioning. Insufficient cooling. o cool air comes out. (ir flow volume is normal.) ulti V system ower supply system of rear / control Rear / control ommunication circuit between rear / control and / auto amp. / auto amp. ircuit between rear mode door motor and / auto amp. Rear mode door motor control linkage ront mode door motor / auto amp. ircuit between rear air mix door motor and / auto amp. Rear air mix door motor installation condition Rear air mix door motor / auto amp. ower supply system of rear blower motor ircuit between rear blower motor and / auto amp.. Rear blower motor / auto amp. ower supply system of rear / relay ircuit between rear / relay and / auto amp.. ircuit between rear / relay and rear / solenoid valve. ircuit between rear / solenoid valve and ground. Rear / relay Rear / solenoid valve / auto amp. Refrigerant cycle ir leakage from each duct Temperature setting trimmer (rear) V-199, "Symptom Table" -115, "RR / TR : iagnosis rocedure" -127, "iagnosis rocedure" -116, "RR R TR : iagnosis rocedure" -114, "RR IR IX R TR : iagnosis rocedure" -131, "iagnosis rocedure" -139, "RR IR I- TIR : iagnosis rocedure" -135

RR UTTI IR ITII SYST < SYT ISIS > [UTTI IR ITII] Symptom orresponding malfunction part Reference Insufficient heating. o warm air comes out. (ir flow volume is normal.) oise is heard when rear blower motor operates. ngine cooling system eater hose Rear heater core ir leakage from each duct Temperature setting trimmer (rear) ixing any foreign object in rear blower motor Rear blower motor fan breakage Rear blower motor rotation inferiority -141, "RR IR I- TIR : iagnosis rocedure" -132, "omponent Inspection" -136

S (V IT TR SYST) < SYT ISIS > [UTTI IR ITII] S (V IT TR SYST) Symptom Table II:0000000006275982 T: erform the self-diagnoses with SUT-III before performing the symptom diagnosis. If T is detected, perform the corresponding diagnosis. The following table is based on the condition that front automatic air conditioning system operates normally. Symptom orresponding malfunction part Reference uto intake switch cannot be operated. [utomatic intake control (exhaust gas / outside odor detecting mechanism) does not operate] ulti V system V-199, "Symptom Table" lasmacluster control does not operate. T: lasmacluster ion technology developed by Sharp orporation is installed in this item. lasmacluster is a trademark of Sharp orporation. ower supply system of ionizer The circuit between ionizer and / auto amp. Ionizer / auto amp. -124, "iagnosis rocedure" peration status of lasmacluster control does not switch according to air flow. T: lasmacluster ion technology developed by Sharp orporation is installed in this item. lasmacluster is a trademark of Sharp orporation. / auto amp. Replace / auto amp.. Refer to -146, "Removal and Installation". -137

ISUIIT I < SYT ISIS > [UTTI IR ITII] ISUIIT I RT IR ITIR RT IR ITIR : escription II:0000000006275984 Symptom Insufficient cooling o cool air comes out. (ir flow volume is normal.) RT IR ITIR : iagnosis rocedure II:0000000006275985 T: erform self-diagnoses with SUT-III before performing symptom diagnosis. If any T is detected, perform the corresponding diagnosis. 1. T UT RTI 1. Turn ignition switch. 2. perate fan switch. 3. ress / switch. 4. heck that / indicator turns. heck visually and by sound that compressor operates. 5. ress / switch again. 6. heck that / indicator turns. heck that compressor stops. YS >> T 2. >> erform diagnosis of RSSR S T RT in SYT ISIS. Refer to -142, "iagnosis rocedure". 2. RIV T heck tension of drive belt. Refer to -20, "hecking". YS >> T 3. >> djust or replace drive belt depending on the inspection results. 3. RRIRT Y onnect recovery/recycling recharging equipment to the vehicle and perform pressure inspection with gauge. Refer to -27, "Symptom Table". YS >> T 4. >> Repair or replace parts depending on the inspection results. 4. IR R UT heck duct and nozzle, etc. of the front air conditioning system for leakage. YS >> T 5. >> Repair or replace parts depending on the inspection results. 5. IT TRTUR ISY heck that there is not much diference between actual ambient temperature and indicated temperature on information display in combination meter. YS >> T 6. >> erform diagnosis for the / auto amp. connection recognition signal circuit. Refer to WI-74, "iagnosis rocedure". 6. STTI TRTUR STTI TRIR (RT) 1. heck setting value of temperature setting trimmer (front). Refer to -68, "RT UTTI IR ITII SYST : Temperature Setting Trimmer (ront)". 2. heck that temperature setting trimmer (front) is set to + direction. -138

ISUIIT I < SYT ISIS > [UTTI IR ITII] T: The control temperature can be set with the setting of the temperature setting trimmer (front). 3. Set difference between set temperature and control temperature to 0. Is inspection result normal? YS >> ISTI >> Replace / auto amp.. Refer to -146, "Removal and Installation". RR IR ITIR RR IR ITIR : escription II:0000000006275986 Symptom Insufficient cooling o cool air comes out. (ir flow volume is normal.) RR IR ITIR : iagnosis rocedure II:0000000006275987 T: erform self-diagnoses with SUT-III before performing symptom diagnosis. If any T is detected, perform the corresponding diagnosis. 1. RR / SI VV heck rear / solenoid valve. Refer to -128, "iagnosis rocedure". YS >> T 2. >> Repair or replace malfunctioning parts. 2. RRIRT Y onnect recovery/recycling recharging equipment to the vehicle and perform pressure inspection with gauge. Refer to -27, "Symptom Table". YS >> T 3. >> Repair or replace parts depending on the inspection results. 3. IR R UT heck duct and nozzle, etc. of the rear air conditioning system for leakage. YS >> T 4. >> Repair or replace parts depending on the inspection results. 4. STTI TRTUR STTI TRIR (RR) 1. heck setting value of temperature setting trimmer (rear). Refer to -69, "RR UTTI IR ITII SYST : Temperature Setting Trimmer (Rear)". 2. heck that temperature setting trimmer (rear) is set to + direction. T: The control temperature can be set with the setting of the temperature setting trimmer (rear). 3. Set difference between set temperature and control temperature to 0. Is inspection result normal? YS >> ISTI >> Replace / auto amp.. Refer to -146, "Removal and Installation". -139

ISUIIT TI < SYT ISIS > [UTTI IR ITII] ISUIIT TI RT IR ITIR RT IR ITIR : escription II:0000000006275990 Symptom Insufficient heating o warm air comes out. (ir flow volume is normal.) RT IR ITIR : iagnosis rocedure II:0000000006275991 T: erform self-diagnoses with on board diagnosis and SUT-III before performing symptom diagnosis. If T is detected, perform the corresponding diagnosis. 1. I SYST 1. heck engine coolant level and check leakage. Refer to -8, "Inspection". 2. heck reservoir tank cap. Refer to -11, "RSRVIR T : Inspection". 3. heck water flow sounds of the engine coolant. Refer to -9, "Refilling". YS >> T 2. >> Refill engine coolant and repair or replace parts depending on the inspection results. 2. TR S heck installation of heater hose by visually or touching. YS >> T 3. >> Repair or replace parts depending on the inspection results. 3. RT TR R 1. heck temperature of inlet hose and outlet hose of front heater core. 2. heck that inlet side of front heater core is hot and the outlet side is slightly lower than/almost equal to the inlet side. UTI: lways perform the temperature inspection in a short period of time because the engine coolant temperature is very hot. YS >> T 4. >> Replace front heater core. Refer to -44, "TR R : Removal and Installation". 4. IR R UT heck duct and nozzle, etc. of front air conditioning system for air leakage. YS >> T 5. >> Repair or replace parts depending on the inspection results. 5. STTI TRTUR STTI TRIR (RT) 1. heck setting value of temperature setting trimmer (front). Refer to -68, "RT UTTI IR ITII SYST : Temperature Setting Trimmer (ront)". 2. heck that temperature setting trimmer (front) is set to direction. T: The control temperature can be set by the temperature setting trimmer (front). 3. Set difference between the set temperature and control temperature to 0. re the symptoms solved? YS >> ISTI >> Replace / auto amp.. Refer to -146, "Removal and Installation". RR IR ITIR -140

ISUIIT TI < SYT ISIS > [UTTI IR ITII] RR IR ITIR : escription Symptom Insufficient heating o warm air comes out. (ir flow volume is normal.) RR IR ITIR : iagnosis rocedure II:0000000006275992 II:0000000006275993 UTI: erform the self-diagnoses with on board diagnosis and SUT-III before performing symptom diagnosis. If any malfunction result or T is detected, perform the corresponding diagnosis. 1. I SYST 1. heck engine coolant level and check leakage. Refer to -8, "Inspection". 2. heck reservoir tank cap. Refer to -11, "RSRVIR T : Inspection". 3. heck water flow sounds of the engine coolant. Refer to -9, "Refilling". YS >> T 2. >> Refill the engine coolant and repair or replace the parts depending on the inspection results. 2. TR S heck installation of heater hose by visually or touching. YS >> T 3. >> Repair or replace parts depending on the inspection results. 3. RR TR R 1. heck temperature of inlet hose and outlet hose of rear heater core. 2. heck that the inlet side of rear heater core is hot and the outlet side is slightly lower than/almost equal to the inlet side. UTI: lways perform the temperature inspection in a short period of time because the engine coolant temperature is very hot. YS >> T 4. >> Replace rear heater core. Refer to -48, "TR R : Removal and Installation". 4. IR R UT heck duct and nozzle, etc. of the rear air conditioning system for air leakage. YS >> T 5. >> Repair or replace parts depending on the inspection results. 5. STTI TRTUR STTI TRIR (RR) 1. heck setting value of temperature setting trimmer (rear). Refer to -69, "RR UTTI IR ITII SYST : Temperature Setting Trimmer (Rear)". 2. heck that the temperature setting trimmer is set to direction. T: The control temperature can be set by the temperature setting trimmer (rear). 3. Set the difference between the set temperature (rear) and control temperature to 0. re the symptoms solved? YS >> ISTI >> Replace / auto amp.. Refer to -146, "Removal and Installation". -141

RSSR S T RT < SYT ISIS > [UTTI IR ITII] RSSR S T RT escription II:0000000006275994 Symptom: ompressor dose not operate. iagnosis rocedure II:0000000006275995 T: erform self-diagnoses with SUT-III before performing symptom diagnosis. If T is detected, perform the corresponding diagnosis. heck that refrigerant is enclosed in cooler cycle normally. If refrigerant amount is shortage from proper amount, perform inspection of refrigerant leakage. 1. T UT RTI heck magnet clutch. Refer to -126, "omponent unction heck". oes it operate normally? YS >> T 2. >> Repair or replace malfunctioning parts. 2. RRIRT RSSUR SSR heck refrigerant pressure sensor. Refer to -520, "omponent unction heck". YS >> T 3. >> Repair or replace malfunctioning parts. 3. / UT. UTUT SI With SUT-III heck RQ SI and RQ SI in T ITR mode of V using SUT-III. onitor item ondition Status RQ SI / switch n RQ SI ront blower motor ff YS >> T 4. >> Replace / auto amp.. Refer to -146, "Removal and Installation". 4. IUT SI With SUT-III heck IR SI and TR SW in T ITR mode of using SUT-III. n ff onitor item ondition Status RQ SI n TR SW ront blower motor ff YS >> T 5. >> heck communication system. Refer to -18, "Trouble iagnosis low hart". 5. I /R IUT SI With SUT-III 1. Start engine. / switch n ff -142

RSSR S T RT < SYT ISIS > [UTTI IR ITII] 2. heck RQ in T ITR mode of I /R using SUT-III. onitor item ondition Status RQ / switch n ff YS >> ISTI >> heck communication system. Refer to -18, "Trouble iagnosis low hart". -143

RT / TR < RV ISTTI > [UTTI IR ITII] RV ISTTI RT / TR Removal and Installation II:0000000006275996 RV 1. Remove cluster lid. Refer to I-14, "Removal and Installation". 2. Remove preset switch. Refer to V-227, "Removal and Installation". 3. isconnect harness connector from front / control. ISTTI Install in the reverse order of removal. -144

RR / TR < RV ISTTI > [UTTI IR ITII] RR / TR Removal and Installation RV 1. Remove console rear finisher. Refer to I-29, "Removal and Installation". 2. Remove fixing screws, and then remove rear / control. ISTTI Install in the reverse order of removal. II:0000000006275997-145

/ UT. < RV ISTTI > [UTTI IR ITII] / UT. Removal and Installation II:0000000006275999 RV 1. Remove cluster lid lower. Refer to I-14, "Removal and Installation". 2. Remove V control unit. Refer to V-212, "Removal and Installation". 3. isconnect harness connector from / auto amp.. 4. Remove fixing screws, and then remove / auto amp.. ISTTI Install in the reverse order of removal. -146

IT SSR < RV ISTTI > [UTTI IR ITII] IT SSR Removal and Installation RV 1. Remove front grill. Refer to XT-19, "Removal and Installation". 2. isengage the pawl, and then remove ambient sensor from bracket. 3. isconnect ambient sensor connector, and then remove the ambient sensor. ISTTI Install in the reverse order of removal. II:0000000006276000-147

I-VI SSR < RV ISTTI > [UTTI IR ITII] I-VI SSR RT / UIT SSY RT / UIT SSY : Removal and Installation RV 1. Remove instrument lower panel. Refer to I-14, "Removal and Installation". 2. Remove fixing screw, and then remove in-vehicle sensor. ISTTI Install in the reverse order of removal. RR / UIT SSY RR / UIT SSY : Removal and Installation II:0000000006276001 II:0000000006276002 RV 1. Remove rear / unit assembly. Refer to -47, "RR / UIT SSY : Removal and Installation". 2. Remove the intake sensor from rear / unit assembly. ISTTI ote the following items, and install in the reverse order of removal. UTI: Replace -rings with new ones. Then apply the compressor oil to them when installing. ark the mounting position of intake sensor bracket prior to removal so that the reinstalled sensor can be located in the same position. ever rotate the bracket insertion part when removing and installing the intake sensor. heck for leakages when recharging refrigerant. Refer to -18, "eak Test". -148

SU SSR < RV ISTTI > [UTTI IR ITII] SU SSR Removal and Installation RV II:0000000006276003 1. Remove upper ventilator grill R. Refer to VT-10, "UR VTITR RI : Removal and Installation". 2. Remove sunload sensor from front defroster grill R. 3. isconnect harness connector from sunload sensor. ISTTI Install in the reverse order of removal. -149

IT SSR < RV ISTTI > [UTTI IR ITII] IT SSR xploded View Refer to -41, "xploded View". Removal and Installation II:0000000006276004 II:0000000006276005 RV 1. Remove the front evaporator assembly. Refer to -43, "VRTR : Removal and Installation". 2. Remove the intake sensor from front evaporator. ISTTI ote the following items, and install in the reverse order of removal. UTI: Replace -rings with new ones. Then apply the compressor oil to them when installing. ark the mounting position of intake sensor bracket prior to removal so that the reinstalled sensor can be located in the same position. ever rotate the bracket insertion part when removing and installing the intake sensor. heck for leakages when recharging refrigerant. Refer to -18, "eak Test". -150

XUST S/UTSI R SSR < RV ISTTI > [UTTI IR ITII] XUST S/UTSI R SSR Removal and Installation RV 1. Remove bumper molding. Refer to XT-13, "Removal and Installation". 2. Remove bolt, and then remove exhaust gas/outside odor sensor. ISTTI Install in the reverse order of removal. II:0000000006276007-151

R TR < RV ISTTI > [UTTI IR ITII] R TR xploded View ront / unit II:0000000006276008 II0645ZZ 1. / unit assembly 2. Upper ventilator door lever 3. Upper ventilator door link 4. Upper ventilator door motor 5. ir mix door motor 6. ir mix door adaptor 7. ir mix door adaptor 8. Intake door motor 9. Intake door motor lever 10. Intake door lever 11. lower unit assembly 12. oot door lever 13. oot door link 14. ir mix door motor R 15. ir mix door adaptor 16. ode door motor 17. ode door motor lever 18. ode door motor bracket 19. ain link 20. Ventilator door link 21 Ventilator door lever 22. efroster lever Rear / unit II0646ZZ -152

R TR < RV ISTTI > [UTTI IR ITII] 1. Rear / unit assembly 2. Rear mode door lever 2 3. Rear mode door lever 1 4. Rear mode door motor 5. Rear air mix door motor R TR R TR : Removal and Installation RV 1. Remove instrument lower panel R. Refer to I-14, "Removal and Installation". 2. Remove power steering control unit bracket. 3. Remove fixing screws (), and then remove mode door motor (1). 4. isconnect mode door motor connector. II:0000000006276009 ISTTI Install in the reverse order of removal. IR IX R TR IR IX R TR : Removal and Installation II0790ZZ II:0000000006276010 RV river side 1. Remove automatic drive position control unit. Refer to -136, "Removal and Installation". 2. Remove fixing screws (), and then remove air door motor (1). 3. isconnect air mix door motor connector. assenger side 1. Remove heater core. Refer to -44, "TR R : Removal and Installation". 2. Remove fixing screws, and then remove air mix door motor R. ISTTI Install in the reverse order of removal. IT R TR IT R TR : Removal and Installation RV 1. Remove blower unit assembly. Refer to VT-15, "Removal and Installation". 2. Remove fixing screws, and then remove intake door motor. II0788ZZ II:0000000006276011-153

R TR < RV ISTTI > [UTTI IR ITII] 3. isconnect intake door motor connector. ISTTI Install in the reverse order of removal. UR VTITR R TR UR VTITR R TR : Removal and Installation II:0000000006276012 RV 1. Remove automatic drive position control unit. Refer to -136, "Removal and Installation". 2. Remove fixing screws (), and then remove intake door motor (1). 3. isconnect intake door motor connector. II0789ZZ ISTTI Install in the reverse order of removal. RR R TR RR R TR : Removal and Installation II:0000000006276013 RV 1. Remove luggage side lower finisher R. Refer to IT-36, "U SI WR IISR : Removal and Installation". 2. Remove fixing screws, and then remove rear mode door motor. ISTTI Install in the reverse order of removal. RR IR IX R TR RR IR IX R TR : Removal and Installation II:0000000006276014 RV 1. Remove rear / unit assembly. Refer to -47, "RR / UIT SSY : Removal and Installation". 2. Remove fixing screws, and then remove air mix door motor. ISTTI Install in the reverse order of removal. -154

IIZR < RV ISTTI > [UTTI IR ITII] IIZR xploded View II:0000000006276015 Refer to -41, "xploded View". Removal and Installation II:0000000006276016 Removal 1. Remove instrument lower panel. Refer to I-14, "Removal and Installation". 2. Remove mounting screws, and then remove ionizer from / unit assembly. UTI: ever tough the surface (ceramic part) of the ionizer. It is the discharge electrode. 3. isconnect ionizer harness connector. ISTTI ote the following item, install in the reverse order of removal. UTI: If there is dirt, use a clean cloth and clean the discharge electrode (ceramic part) of the ionizer. -155