Installation Manual. Table of Contents. System Requirements. PC Console Software. Model no. KX-TDA0300

Transcription

1 PC Console Software Installation Manual Model no. KX-TDA0300 Thank you for purchasing the Panasonic PC Console Software, KX-TDA0300. Please read this manual before using this product and save for future use. This manual is designed to provide instructions for installing the PC Console Software and USB driver on your personal computer. Table of Contents System Requirements... 1 Introduction... 2 Conditions... 2 Installing the PC Console Software... 3 Installing the USB Driver... 7 Windows Windows Windows XP Updating the USB Driver Windows Windows Windows XP Deleting the USB Driver Windows Windows Windows XP Uninstalling the PC Console Software. 31 Starting the PC Console Software System Requirements Microsoft Windows 98 Second Edition, 2000, or XP (Windows Me is not supported) Internet Explorer 5.0 or later Minimum Requirements (for installing the KX-TDA0300 only) CPU: Pentium II 350 MHz RAM: 64 MB HDD: 100 MB available space (when installing) Display: XGA (1024*768) Peripheral Devices: Sound Board (for recording and replying features), Speaker (for listening to voice messages), USB port, CD-ROM drive Trademarks Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Pentium is either a registered trademark or a trademark of Intel Corporation or its subsidiaries in the United States and other counties. All other trademarks identified herein are the property of their respective owners. Note: Screen shots reprinted with permission from Microsoft Corporation.

2 Introduction The PC Console is designed to interwork with Panasonic Hybrid-IP PBX (KX-TDA Series), and enables the personal computer to handle calls instead of the proprietary telephone. Notice: The PC Console handles a maximum of 10 calls at a time. To receive more than one call simultaneously, you first need to assign the desired number of Incoming Call Distribution Group buttons (max. 10) to the proprietary telephone assigned as the PC Console. If you assign more than 10 buttons, you may not be able to receive or make a call. For assignment, consult your dealer. The extension to which the PC Console is assigned should be given the DPT port property under the system programming of the PBX (Terminal Device Assignment [601]). For programming, consult your dealer. Conditions Before installation, the PBX must be turned on. The Panasonic digital proprietary telephone (KX-T7633 and KX-T7636 only) must be equipped with the USB Module KX-T7601, and a USB cable should connect your PC and the telephone. For installation instructions, refer to the documentation of the KX-T7600 series. To install the PC Console on, or to uninstall it from a PC running Windows 2000 or XP Professional, you should be in the group Administrators. The user in any other groups is not authorised. Be sure to assign a private folder as Data Folder when installing the software, if the user of the PC Console is not in the group Administrators. Do not assign any of system folders, including Program Files folder. Otherwise, the application does not run properly. While operating the PC Console, System Standby Mode (Suspend) and Hibernation should be disabled. Depending on the OS, the default audio device of the PC will be switched to the USB Audio Device that is installed at the time of USB Driver installation. To playback audio, reselect the preferred device via the Control Panel. If a connection error message appears during the operation, exit from the PC Console, confirm the following, then restart the PC Console. A TEL cord connects the PBX and the telephone. A USB cable connects the telephone and the PC. The PBX is turned on. If you have any questions or experience any improper performance, consult your dealer. 2

3 Installing the PC Console Software Notice: Shutdown any other applications before installing the software. 1. Double-click Setup.exe on the CD-ROM. 2. Click Next. 3. Read the Licence Agreement carefully. 3

4 Installing the PC Console Software 4. If you accept the terms of the License Agreement, click Yes. 5. Click Browse to change the installation folder. This step is optional, and can be skipped. 6. Click Next. 7. Rename the program folder in the Program Folders: field. This step is optional, and can be skipped. 4

5 Installing the PC Console Software 8. Click Next. 9. Click Browse to change the location to save work data. This step is optional, and can be skipped. 10.Click Next. 11.Enter the extension number of the extension to which the PC Console is set, then click OK. 12.Enter the administrator s name (max. 16 characters) and the password (max. 10 characters). Available characters: (space)! # $ % & ( ) * +, -. / : ; < = A B C D E F G H I J K L M N O 5

6 Installing the PC Console Software Available characters: P Q R S T U V W X Y Z [ \ ] ^ _ ` a b c d e f g h i j k l m n o p q r s t u v w x y z { } ~ 13.Click OK. 14.Enter the password again, then click OK. 15.Click OK. 16.Click Finish. 6

7 Installing the USB Driver Note: Windows 98 Depending on the environment of your PC, you may need the Windows 98 installation CD-ROM when installing the USB Composite Device and USB Audio Device. 1. Connect your telephone to your PC with the USB cable. 2. Click Next. 7

8 Installing the USB Driver 3. Select Search for the best driver for your device. [Recommended], then click Next. 4. Select CD-ROM drive, then click Next. 5. Click Next. 8

9 Installing the USB Driver 6. Click Finish. 7. Click Next. 8. Select Search for the best driver for your device. [Recommended], then click Next. 9

10 Installing the USB Driver 9. Select CD-ROM drive, then click Next. 10.Click Next. 11.Click Finish. Note: If your PC recommends, restart your PC. 10

11 Installing the USB Driver 12.Click Next. 13.Select Search for the best driver for your device. [Recommended], then click Next. 14.Select CD-ROM drive and Specify a location. 11

12 Installing the USB Driver 15.Click Browse to specify CD-ROM Drive:\TDAUSBPT\Win_98, then click Next. 16.Click Next. 17.Click Finish. Note: If your PC recommends, restart your PC. 12

13 Windows Connect your telephone to your PC with the USB cable. Installing the USB Driver 2. Click Next. 13

14 Installing the USB Driver 3. Select Search for a suitable driver for my device. [Recommended], then click Next. 4. Select CD-ROM drives, and then click Next. 5. Click Next. 14

15 Installing the USB Driver 6. Click Finish. Windows XP 1. Connect your telephone to your PC with the USB cable. 2. Select Install from a list or specific location [Advanced], then click Next. 3. Select Search for the best driver in these locations. 15

16 Installing the USB Driver 4. Select Search removable media [floppy, CD-ROM...], then click Next. 5. Click Continue Anyway. 6. Click Finish. 16

17 Updating the USB Driver Windows Open Device Manager. 2. Click Properties, and click the Driver tab. 17

18 Updating the USB Driver 3. Click Update Driver. 4. Click Next. 5. Select Display a list of all the drivers in a specific location, so you can select the driver you want., and click Next. 18

19 Updating the USB Driver 6. Select Panasonic KXTDAUSB PT Unit driver, then click Have Disk. 7. Click Browse to specify the TDAUSBPT folder, then click OK. 8. Select Panasonic KXTDAUSB PT Unit driver, then click Next. 9. Click Yes. 19

20 Updating the USB Driver 10.Click Next. 11.Click Finish. Windows Open Device Manager. 20

21 Updating the USB Driver 2. Right-click Panasonic KXTDAUSB PT Unit driver (under Universal Serial Bus controllers), then click Properties. 3. Click the Driver tab, then click Update Driver. 21

22 Updating the USB Driver 4. Click Next. 5. Select Display a list of the known drivers for this device so that I can choose a specific driver, then click Next. 6. Select Show compatible hardware, then click Have Disk. 22

23 7. Click Browse to specify the TDAUSBPT folder, then click OK. Updating the USB Driver 8. Select Panasonic KXTDAUSB PT Unit driver, then click Next. 9. Click Next. 23

24 Updating the USB Driver 10.Click Finish. Windows XP 1. Open Device Manager. 24

25 Updating the USB Driver 2. Right-click Panasonic KXTDAUSB PT Unit driver, then click Update Driver. 3. Select Install from a list or specific location [Advanced], then click Next. 25

26 Updating the USB Driver 4. Select Don t search. I will choose the driver to install., then click Next. 5. Click Have Disk. 6. Click Browse to specify the TDAUSBPT folder, then click OK. 26

27 7. Select Panasonic KXTDAUSB PT Unit driver, then click Next. Updating the USB Driver 8. Click Continue Anyway. 9. Click Finish. 27

28 Deleting the USB Driver Windows Open Device Manager. 2. Select Panasonic KXTDAUSB PT Unit driver, then click Remove. 3. Click OK. 28

29 Deleting the USB Driver Windows Open Device Manager. 2. Right-click Panasonic KXTDAUSB PT Unit driver, then click Uninstall. 3. Click OK. 29

30 Deleting the USB Driver Windows XP 1. Open Device Manager. 2. Right-click Panasonic KXTDAUSB PT Unit driver, then click Uninstall. 3. Click OK. 30

31 Uninstalling the PC Console Software Uninstall the software from [Control Panel] -> [Add/Remove Programs]. Starting the PC Console Software Notice: When logging-in to the PC Console, you are required to enter the Registration Key of the product for permanent full access to all features. The input dialogue box will not appear once you properly assign the Registration Key. Without the Registration Key, the PC Console will be available for only 30 days. For acquiring a Registration Key, consult your dealer. 1. Start PC Console. 2. Enter the Operator Name and the Password you assigned when installing the PC Console. 3. Click OK. 31

32 Starting the PC Console Software Notes: When logging-in to the PC Console for the first time, it may take several minutes to retrieve the necessary data. If Wave Devices have not been assigned in the Utility Setting, the following dialogue box appears: Sound playback by PC: Assign a sound device. Note you cannot select a USB Audio Device for sound playback by PC. Sound transfer / receive with PBX: Assign the USB Audio Device installed at the time of USB Driver installation. If the extension number registered in the PC Console is different from that of the actual device (connected to the PC), the following dialogue box appears: Extension Number: Enter the correct extension number. 32

33 33

34 Panasonic Communications Co., Ltd. 1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka , Japan Copyright: This material is copyrighted by Panasonic Communications Co., Ltd., and may be reproduced for internal use only. All other reproduction, in whole or in part, is prohibited without the written consent of Panasonic Communications Co., Ltd Panasonic Communications Co., Ltd. All Rights Reserved. PSQX2885XA KK0303EB2074