Operation Manual Magic Bowling. Warning Please read this manual carefully before using this machine

Transcription

1 Operation Manual Magic Bowling Warning Please read this manual carefully before using this machine

2 Preface 1. Company profile: Zhongshan star amusement equipment Co., Ltd, ltd, which designs and manufactures amusement equipments, has redemption machines, music machines, simulator game, kiddy ride, bumping car, smaller carousel and other indoor rides. Owing to the advanced technical engineers with more than 10 years experience in mechanical and electronic research and development, our company is so confident to make new design machines every month. Company was founded with perfect quality control and supervision system, and always takes honesty, best service, best quality, and customer first as principle. 2. Products introduction: Magic bowling is designed through well programmed scoring system;fast game play, various difficulty levels;operator adjustable payout - Highly quality and sturdy cabinet built for durability; Easy assembly / disassembly structure. 3. Notice 1. Firstly put down the angle of machine to adjust level for the machine. 2. Check the strap if shift or not, if not, it should be adjustable before operation. 3. There has sensors so that the machine should be kept clean to ensure that the effect of sensor. 4. In order to extend its longevity, please don t place it outside. 1

3 Content 1. Specification and technical parameter 2. List of Components 3. Place, settlement, movement and maintenance 4. Power cord connection 5. Game way instruction: 6. Control signal 7. Shooting organ adjustment: 8. Operation and maintenance 9. Main components 10. Packing and Installation 11. Malfunction and solution 2

4 1. Specification and technical parameter: (1) Voltage:AC 220V±10% 50Hz or 110V±10% 60Hz; (2) Power:MIN: 60W MAX: 110W; (3) Measurement: L1900 W710 H2200(mm) (4) Weight: 165 KG (5) Environmental condition: interior temperature: -10 ~ +40 humidity: 90%;Pressure: 86Pa~106Pa; Note: We do not inform each time if above information have changed. 2. List of Components In order to use this machine normally, please check whether following spare parts are available (1) Main machine: one piece (2) Spare parts list as following No Name Regulation Qty Picture Note 1 Power wire 10A/250V 1.8m 1 2 Fuse 6.3 A/250V Φ5-20MM 1 220V 3 Manual 1 4 Key X919 1 Front and back door X818 1 Coin box 5 Micro switch 1 bowling Shooting inside 3

5 6 Micro switch 1 Use in shooting button 7 Ball 55 Note: We are not notifying if any data will be changed. 3. Place, settlement, movement and maintenance 3-1. Assemble ground Warning For indoor use only! 3-2. Assemble area(mm) Machine must be put as following location machines 300 Play area The machine cannot be used in the following places: Notice Location exposed to direct sunlight. Locations subject to rain or water leakage. Unstable locations subject to vibration. Dusty, hot, damp locations. 4

6 3-4. Fixture and movement The machine must be laid down on the floor, please put down top wheel, to use slide wheel back to top wheel if moving. Adjusting base for foundation The method of delivery The machine must be wrapped up a soft pad around the surface of machine to avoid crush when long-distance carry, packing and fixing up. Notice Disconnect game power before moving. Make sure all wheels are intact. Replace any wheels that are damaged or broken before moving the game. When moving the game. Do not slide the game across the floor Ensure the game is level before connecting the power Maintenance Open front door and back door to repair machine. 4. Power cord connection Power socket Electricity wire box Power plug Power plug Electricity wire 5

7 Notice Do not put heavy item on power cord. Hold the power plug instead of the wire to draw the power cord of the socket. Do not touch the power plug with wet hands. Do not draw or twist the cord or near a heat source. Do not place the cord where the player can easily trip over or come in contact with it. Operate this game with the correct power and fuse configuration. 5. Game way instruction: (1) Insert coin(s) to start. The ball hit the target to get the points; If press the button long time, it could be shooting continuously. (2)The highest points you get, the more payout you take. 6

8 (3)The highest score and payout are according to I/O chart setting. 6. Control signal (1)Refer to I/O chart and Schematic diagram, diagram of motherboard input and output each connection. (2)Refer to I/O chart as capital letter, user adjustable feature base on operation. (3) Main board plan: Sound memorizer1 Sound memorizer2 7. Shooting organ adjustment: Loose Tight 4 7

9 1 plastic wheel 2 motor 3nut 4adjustment screw 5 shooting adjustment Loosen nut with 5/16 wrench Turn adjustment screw with 3mm Allen wrench: Turn screw clockwise to decrease the shooting force of the ball. Turn screw counter clockwise to increase the shooting force of the ball. Tighten nut A worn wheel will cause little or no force of the ball Replace the wheel if visibly worn or damaged. 8. Operation and maintenance (1) Turn off the power before the repair and maintain. In order to avoid the short circuit, cut off the power before operation. It must be complied with requirement of instruction (2) To use the proper accessories when replace the components. Using the wrong accessories will cause short circuit, damage the PCB board and components. (3) Don t remove, assemble, modify in random. It might cause short circuit and malfunctions, even fire. (4)Don t put the vase, cup and container, chemical and heavy things, because the liquid will cause short circuit and damage, broke machines and hurt someone as well. (5) Don t place the things on air outlet. It will cause internal temperature increasing, even damage kits. (6)Do not repair the machine randomly. It might cause short circuit or outing of control. 8

10 9. Main components 9-1. Front plan: Maximum points JP payout Score Targets Time Shooting button Speaker Ticket dispenser Key Coin selector 9-2. Power supply box: a. The machine is AC 220V ±10% 50Hz or 110V±5% 60HZ(The actual voltage please refer to card plate). b. AC fuse inside fuse box, specification: 220V 6.3A, Φ5-20mm or 110V/6.3A Φ5-20mm. Electricty wire box Ground end Electricity power switch fuse socket Electrcity socket 9

11 9-3. Coin selector 1. When coin selector blocks coin, please dial button as picture, coin will come out. If still cannot come out, must disassemble coin selector to take out coin. Instruction of electronic compare coin selector a. Take out the plastic coin from coin slot, displace the proper coin b. Loose bolts at the back of coin mouth,use coin diameter to adjust stator at the back of coin mouth,avoid error caused by big diameter. c. Fit for game board needs,choose COIN long short and fast slow three phase switch (TIMER SWITCH):30ms is short fast signal,fit for machine has high power and need insert coin quickly,50ms is middle signal, fit for ordinary machines (if not special machine usually can use this phase),100ms is long slow signal, fit for machine that don t need insert coin quickly. d. VR coin choose sensitivity adjustment,anticlockwise adjustment( ), accept smaller area of coin tolerance,the mean is filtration more strictly. e. Wire connection: 1 Grey cord Red cord-dc+12v 2 White cord-coin signal 3 Black cord-ground cord 4 Grey cord Code chart 9-3:Ticket dispenser 10

12 low Driving signal choose Feedback signal choose show light Ticket machine plug OUT signal output + power :+12V GND power :ground IN putput +12V This game use above ticket dispenser, driving signal and feedback signal all choose low. 10. Packing and Installation In order to transportation, we can remove the fiberglass before shipping as below: Firstly connect the circuit of toys, loose the tight screws, taking off the toys. Install the fiberglass on the top as picture (left) Packing and fasten the machines, please warp some bubby bags around the angles and wooden packing to avoid damaging the machines. 11

13 11. Malfunction and solution Item Problem Probable Cause Solution 1 Coin can t be in Coin selector is not adjusting. Adjust coin selector 2 No tickets 3 Ball disability 4 No points to target No 12V input to ticket dispenser. The drive signal or cancelled signal cord of ticket dispenser loosen. Press ticket wheel is not pressing tickets. Ticket dispenser of main board drive or cancelled port broken. No ticket on main board. Plastic coaster damaged. Not enough 24V power supply. Sensor broken no power on GND Main board broken Check the power supply box output voltage and circuit Check voltage of drive cancelled signal and circuit. Put down the press ticket wheel. Replace the main board Ticket mode is setting as ticket out. Adjust ball adjustor. Adjust 24V power voltage up to 24V. Replace sensor Check to connect GND circuit Replace main board 5 Target light broken No 12 supply Light rings broken Output of IC on Main board broken Check 12V power supply box and circuit. Replace light rings. Replace the main board or IC. Ball organ no 6 action 7 No sound No 24V power supply Ball motor broken Ball jammed on ball organ. Turn the volume down Sound output signal cord broken Speaker broken Amplifier broken Check 24V power supply box and circuit. Replace ball motor Turn power first, then ball axis turnover by hand, take out the damaged ball. Turn the volume up Connect the circuit Replace the speaker Replace the main board 8 The machine no action No power input to the machine. Power switch not open. Power fuses broken. No voltage output. No voltage of main board. Main board broken Open power switch and put power plug in. Turn the power switch on. Eliminate electro circuit short circuit and replace new fuse. Replace the power supply box. Connect the power link on host. Replace main board 12

14 13