Proliphix. Installer. Remote Management. Guide

Transcription

1 Proliphix Installer Remote Management Guide

2 Rev 2.0 Page 2 of 21 Table of Contents 1. Intended Audience Remote Management Overview Installer Profile Modification Remote Management Administration Client Account Creation Initial Thermostat Configuration Router Configuration Final Thermostat Configuration Remote Management Interface Login Page Client List Page Installer Profile Page Add Client Page Downloads Page Edit Client Profile Page Device List Page Device Statistics Page TMI Page Customer Assistance...20

3 Rev 2.0 Page 3 of Intended Audience The Remote Management Installer Guide is intended to be used by Authorized Proliphix Dealers/Installers who wish to establish Proliphix Remote Management accounts for their clients. An authorized Proliphix Dealer/Installer will be able to; 1. Configure clients thermostats for Remote Management. 2. Administer and modify clients Remote Management accounts on the Proliphix web site. 3. Remotely manage their client s thermostats and diagnose HVAC problems. The clients of Proliphix Authorized Dealers/Installers should receive a copy of the Proliphix Remote Management User Guide, for them to consult while remotely managing their thermostats.! Note! If a VPN is used to access the thermostats remotely, they will appear to reside on your local network. You will therefore not need to control them through the Proliphix Remote Management Service via the Proliphix web site. However, notification due to alarm conditions will NOT be available with VPN use.

4 Rev 2.0 Page 4 of Remote Management Overview The Proliphix Network Thermostats were designed specifically to communicate directly over the Internet using the Internet Protocol (IP). This capability allows the user to securely access, manage and control their thermostats from anywhere in the world with the use of common web browser. To provide this Remote Management capability, Proliphix has invested significantly to develop a software application running on a secure and highly reliable web server which intercommunicates to registered Proliphix Thermostats on a periodic interval to ensure that each thermostat is reachable by any web browser throughout the internet. This Remote Management Server Software provides user authentication, IP address independence and alarm notification. In Figure 1 below, a user on a web browser somewhere accessible to the Internet, logs onto the Proliphix web site. After the user has authenticated as a registered Proliphix thermostat owner, the server communicates to the thermostat to open a secure channel between the user s web browser and the desired thermostat. Communication between the user and their thermostat can then be invoked by the user through the Remote Management GUI. The user simply clicks on links in the browser to access his/her thermostats with no knowledge of IP addressing. Figure 1 Remote Management and Control Additionally, alarms or alerts detected at the thermostats are communicated immediately to the Proliphix Remote Management Server for processing. Notification of these alarms and exception conditions are then communicated to the user (or their agents) via to either their cell phones or standard accounts.

5 Rev 2.0 Page 5 of Installer Profile Modification As an authorized installer of the Proliphix Internet-enabled Network Thermostat, you have been uniquely assigned the following from Proliphix; a. Installer ID b. Remote Management Username = Installer ID (default) c. Remote Management Password = randomly assigned In addition, Proliphix has created an Installer/Dealer account with the information you have provided. If you have not received this information in a confirmation , please contact Proliphix Customer Service to obtain Dealer/Installer authorization. You should not proceed until this information has been obtained. If you have received your account information, you may modify your account profile to change your contact information or username and password. 1. Proceed to the Proliphix Web Site ( 2. Press the Customer Login button. 3. Login to Remote Management. 4. Click Installer Profile on Client List Page. 5. Verify the information which has been entered in your account. 6. Update your contact information (if necessary) 7. Change your username / password (if desired) 8. Complete all required fields. 9. Press Update Profile.

6 Rev 2.0 Page 6 of Remote Management Administration As an authorized installer of the Proliphix Internet-enabled Network Thermostat, you will need to administer the Remote Management Service for your clients by completing the following sections; 1. Client Account Creation You must repeat the following steps for every thermostat. 2. Initial Thermostat Configuration 3. Router Configuration 4. Final Thermostat Configuration Once you have installed the thermostat(s) and administered the Remote Management Service for your client, your client should consult the Proliphix Remote Management User Guide for instructions and details on managing the thermostats Client Account Creation You must establish accounts for each client to receive a uniquely assigned Customer ID required for configuring their thermostats. 1. Proceed to the Proliphix Web Site ( 2. Press the Customer Login button. 3. Login to Remote Management. 4. Click Add Client on Client List Page. Enter client contact information; 5. Enter client s address. 6. Enter client s address. 7. Change client s username (if desired) 8. Change client s password (if desired) 9. Complete all required fields. 10. Copy down the Customer ID for this client. 11. Uncheck the Disabled box. 12. Press Add Account. Your clients account has now been established. You will want to communicate both the account username and password to the client for them to use for Remote Management. They should refer to the Proliphix Remote Management User Guide to access their thermostats. Now you can perform the initial configuration of your client s thermostats.

7 Rev 2.0 Page 7 of Initial Thermostat Configuration After you have established your client s account and prior to configuring their router, you will need to set some basic parameters in your client s thermostat. Repeat the following steps for each of your client s thermostats which will be remotely managed; 1. Access the General Settings Page through the TMI (See NT100e/h and NT120e/h Configuration Guide). 2. Enter a meaningful Zone Name (if not already done). 3. Press Submit. 4. Login to the Administration Pages of the thermostat (NT100e/h and NT120e/h only). 5. Access the Network Settings Page through the TMI. 6. Set the IP Address Method to Static. 7. Select a unique; a. IP address - local network address b. Subnet Mask - local subnet c. Gateway address - address of local firewall router d. HTTP port number - incoming port number, must be unique for each thermostat! 8. Copy down the IP Address (e.g ) 9. Copy down the HTTP Port Number (default is 8081) 10. Press Submit Router Configuration The client s local firewall router must be configured to accept communication from the Proliphix Server Software. To allow this, you must enable port forwarding in the router. Port forwarding is the generic term used to define how incoming network traffic, received from the Internet, will be passed through the router to a device expecting to receive the information. The Proliphix thermostat is such a device which will expect to receive traffic from the Proliphix Server Software. You must therefore configure the router to receive incoming information from Proliphix and forward it to the thermostat. The Proliphix Network Thermostat is programmed to receive instructions only from the Proliphix Server Software. All other attempts to access the thermostat by malicious individuals or software on the Internet will be rejected by the Proliphix Thermostat. Therefore; 1. Access the Inbound Port Forwarding table in the local router. (Note: Routers are available from many different manufacturers and may therefore identify the port forwarding function by many different terms. Please consult the user guide of the router to properly configure these settings.) 2. Set the router s Incoming/Inbound Port Number to the HTTP Port number retrieved from the Network Settings Page above. 3. For this HTTP Port number, set the router to forward to the local IP Address retrieved from the Network Settings Page above (i.e. the IP address of the thermostat).

8 Rev 2.0 Page 8 of Final Thermostat Configuration In this section you will enable the thermostat to intercommunicate with the Proliphix Web Server Software to establish an operational Remote Management connection between a single thermostat and the Proliphix Server Software. Only after completion of the previous two sections should you; 1. Login to the Administration Pages of the thermostat (NT100e/h and NT120e/h only). 2. Access the Remote Access Page through the TMI. 3. Enter a meaningful Site Name (could be the name or location of the property). 4. Enter your assigned Customer ID into the Customer Information field. 5. Set the Remote Discovery State to Enabled. 6. Press Submit. 7. Press Discover Now. After pressing the Discover Now button the thermostat will attempt to communicate with the Proliphix web site Server Software to identify itself and declare it eligible to be remotely managed over the Internet. The Proliphix Server Software will attempt to call back to the thermostat to exchange information relevant to establishing secure remote connections. After you have invoked the Remote Discovery (i.e. pressed Discover Now), you must wait at least 5 minutes before remotely managing the thermostats. During this interval, the thermostat and the Server Software are establishing an initial connection and transferring relevant account information.

9 Rev 2.0 Page 9 of Remote Management Interface After the thermostats which you have installed have successfully connected with the Proliphix Server Software, you may access the Proliphix web site ( with your dealer/installer account information (administered by Proliphix) to manage your clients thermostats over the Internet. Use the Login button in the Remote Management button group on the Proliphix home page Login Page The Login Page for the Remote Management Interface is shown below; Figure 2 Remote Management Login Page Note that in Figure 2 you have an option to have the Server Software re-issue another password if your password has been forgotten. A new password is administered after the directions in Figure 3 have been followed.

10 Rev 2.0 Page 10 of 21 Figure 3 New Password Administration Page After a successful login, the user is immediately directed to the Client List Page. It is on this page that all thermostats registered and successfully communicating with the Proliphix Server Software are displayed.

11 Rev 2.0 Page 11 of Client List Page The Client List Page includes the Installer s customers listed in a Client table. For each client listed in the table, the alarm information from that client is readily visible. In addition, the clients account profile may be edited or deleted. In the example in Figure 4, Acme Installations has three clients which are Proliphix Network Thermostat customers; Brian McCoy, Jim Hatfield, and John Jones. Each client occupies a row in the Client Table. The name of each client is a link to that client s thermostats and can be clicked to access that client s Device List Page. Figure 4 Client List Page Button Definitions Installer Profile: Page which includes the Installer s (e.g. Acme Installations) editable account information. Add Client: Page which allows the installer to administer new clients whose thermostats will be configured for Remote Management. Downloads: Page which includes utilities for downloading software upgrades for the thermostat. View Clients: Displays Client List (this) Page. Logout: Terminates Remote Management session and returns Installer to Proliphix web site.

12 Rev 2.0 Page 12 of 21 Client List Field Definitions (see Figure 4 above) Client Name: (e.g. Brian McCoy) - Name given to each Installer customer who has thermostats which will be remotely manageable. The coloring of the name represents its status; Blue The client has thermostats which have communicated with the Server Software and are capable of being remotely managed. Clicking on this name will advance you to the client s Device List. Black The client s account has been established but no client thermostats have yet to communicate with the Server Software for Remote Management. You will not be able to access this client s Device List. Alarm: (or alert notification) - Color indicator signifying type of alarm received from any thermostat from this client. Currently there are two classes of alarms communicated by the thermostat to the Server Software. The colors of this thermostat include; Green - There are no alarms pending. Red This is the highest severity level alarm. A Low Temperature Alarm is an example of an alarm at this severity level. If any thermostat from this client experiences a Low Temperature Alarm this indicator will be Red and take precedence over a Yellow indicator. Yellow - This is the lowest severity level alarm. A Filter Change Reminder alert is an example of this severity level. This alarm will be pre-empted by a Red alarm condition. Edit {Client} Profile: - Directs the user to the Client Profile Page. Information on this page includes the client contact information, and notification accounts. (See Section 3.5) 5.3.

13 Rev 2.0 Page 13 of 21 Installer Profile Page It is within the Installer Profile Page that the installer can change his/her account username and password. The Installer s contact information is also required to provide Remote Management privileges to the clients. Note that the Customer ID noted on this page is synonymous with the Installer s ID Figure 5 Installer Profile Page

14 Rev 2.0 Page 14 of 21 Add Client Page Prior to installing Proliphix Thermostats for a new client, an installer should create a new client account by entering the information within this page. Note that upon entering this page, a unique Customer ID is created automatically by the Server Software. This Customer ID is required to properly configure the client s new thermostats to communicate with the Server Software. (See the Proliphix Remote Management Setup Guide). Note also that the unique Customer ID is assigned to the initial (default) username. The Server Software assigned password is random. Figure 6 Add Client Page The client account may be enabled or disabled by the Installer. The Disabled box must be unchecked to maintain an active account and access the client s thermostats remotely.

15 Rev 2.0 Page 15 of Downloads Page The Downloads page contains links to both the Proliphix Upgrade Utility and its software installer. The Upgrade Utility is a Proliphix application which allows the user the ability to upgrade their thermostats with the latest software features and functions either locally on the same network, or remotely via the Internet. Figure 7 Downloads Page 5.6.

16 Rev 2.0 Page 16 of 21 Edit Client Profile Page The Edit Client Profile Page displays the client account information required for thermostat Remote Management. The Installer may; change the client s username and password, enable/disable the client s account, and administer up to four Notification Accounts. Figure 8 Edit Client Profile Page

17 Rev 2.0 Page 17 of Device List Page The Installer may view each client s thermostats by clicking on that client (Section 3.1). Figures 8a and 8b below, illustrate the Device Lists for each of Brian McCoy and Jim Hatfield respectively. The thermostats for each client are organized in tables headed by the thermostat Site Name. In the example below, Brian McCoy has two thermostats (i.e. Kitchen, Master Bedroom) in one property, Lexington and Jim Hatfield has two (i.e. 1 st floor, 2 nd Floor) in his Cambridge property. Device List Field Definitions (see Figure 4 above) Figure 8a Device List (McCoy) Zone Name: (e.g. Kitchen) - Name given to each thermostat within the Thermostat Management Interface (TMI). The coloring of the name represents its status; Blue The thermostat is reachable for remote management. It continues to successfully intercommunicate with the Proliphix Server Software. If this name is blue, the link is active and the TMI Status & Control (default) page for that thermostat will be viewed. Orange The thermostat is unreachable. The thermostat has successfully notified the server of its existence, but the Server Software is unable to respond to the thermostat. This is usually an indication that the user s firewall router has inhibited access to the thermostat. Red The thermostat is unreachable. The Server Software has not received periodic messaging from the thermostat. It is likely that the thermostat and the Server Software maintained a connection at one time but now that connection has been lost.

18 Rev 2.0 Page 18 of 21 Alarm: (or alert notification) - Color indicator signifying type of alarm received by this thermostat. Currently there are two classes of alarms communicated by the thermostat to the Server Software. The colors of this thermostat include; Green - There are no alarms pending. Red This is the highest severity level alarm. Currently only a Low Temperature Alarm has a severity of this level. If the thermostat experiences a Low Temperature Alarm this indicator will take precedence over a Yellow indicator. Yellow - This is the lowest severity level alarm. Currently only a Filter Change Reminder alert has this severity. This alarm will be pre-empted by a red alarm condition. Device Stats: - Directs the user to the Device Statistics Page. Information on this page includes thermostat statistics, remote management statistics, notification accounts and alarm status details. (See Figure 7 below.) Figure 8b Device List (Hatfield) Note that both the Red and Yellow Alarms illustrated in Figures 8a and 8b respectively propagate up to be visible at the Client List Page as shown in Figure 4.

19 Rev 2.0 Page 19 of Device Statistics Page This Page displays pertinent thermostat specific Remote Management information. Specifically, it contains the thermostat serial number, its last know WAN IP address and port number, the last known discovery exchange, and the time the thermostat was remotely managed. In addition, pending alarms are described more specifically and accounts for alarm notification can be added. Figure 7 Device Stats Page

20 Rev 2.0 Page 20 of TMI Page The Thermostat Management Interface (TMI) Page contains two components, the Remote Management Header and the thermostat TMI. The remote Management Header allows the user to be able to return back to the Device List Page ( View Devices button) to continue viewing other thermostats. The TMI is the same TMI used to manage the thermostat on the local network. The Nantucket Kitchen NT20e thermostat (TMI) is shown in Figure 8 below. Figure 8 Thermostat Management Interface 6. Customer Assistance When contacting Proliphix for technical assistance, please have the following information available: Thermostat model and serial number.

21 Rev 2.0 Page 21 of 21 Type of heating/cooling system (example: gas, oil, or electric; warm air, hot water, heat pump, steam or gravity) Location and number of wires attached to thermostat For additional assistance, please contact Proliphix Technical Support using the following: How to Reach Us: Web: Telephone: 866 IP-LIVING Fax: