Room Air Conditioner SVC MANUAL(General)

Transcription

1 Internal Use Only Room Air Conditioner SVC MANUAL(General) MODEL : General Wall Mounted-Inverter Type CAUTION Before Servicing the unit, read the safety precautions in General SVC manual. Only for authorized service personnel

2 Air Conditioner Service Manual CONTENTS Part 1 General Information 1. Safety Precautions menclature...7 Part 2 Functions & Controls 1. List of Functions & Controls Basic Mode Controls Special Mode Controls Utility Functions Protection Functions & Controls...16 Part 3 Test Run 1. Check before Test Run Test Run Flow chart Test Run Detail...34 Part 4 Trouble Shooting Guide 1. 2-Way, 3-Way Valve Pumping Down Evacuation (All amount of refrigerant leaked) Gas Charging (After Evacuation) Cycle Troubleshooting Guide Electric Parts Troubleshooting Guide Self-diagnosis Function

3 Part 1 General Information 1. Safety Precautions menclature

4 Part 1 General Information 1. Safety Precautions To prevent injury to the user or other people and property damage, the following instructions must be followed. Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified by the following indications. This symbol indicates the possibility of death or serious injury. This symbol indicates the possibility of injury or damage to properties only. Meanings of symbols used in this manual are as shown below. Be sure not to do. Be sure to follow the instruction. Dangerous Voltage 1.1 Cautions in Repair Be sure to disconnect the power cable plug from the plug socket before disassembling the equipment for a repair.internal components and circuit boards are at main potential when the equipment is connected to the power cables. This high voltage is extremely dangerous and may cause death or severe injury if come in contact with it. Do not touch the discharging refrigerant gas during the repair work. The discharging refrigerant gas.the refrigerant gas can cause frostbite. Release the refrigerant gas completely at a well-ventilated place first. Otherwise, when the pipe is disconnected, refrigerant gas or refrigerating machine oil discharges and it Can cause injury. When the refrigerant gas leaks during work, perform ventilation. If the refrigerant gas comes in contact with a fire, poisonous gas generates. A case of leakage of the refrigerant and the closed room full with gas is dangerous because a shortage of oxygen occurs. Be sure to perform ventilation. When removing the front panel or cabinet, execute short-circuit and discharge between high voltage capacitor terminals. If discharge is not executed, an electric shock is caused by high voltage resulting in a death or injury. Do not turn the air-conditioner ON or OFF by plugging or unplugging the power plug. There is risk of fire or electrical shock

5 Part 1 General Information Do not use a defective or underrated circuit breaker. Use the correctly rated breaker and fuse. Otherwise there is a risk of fire or electric shock. Install the panel and the cover of control box securely. Otherwise there is risk of fire or electric shock due to dust, water etc. Indoor/outdoor wiring connections must be secured tightly and the cable should be routed properly so that there is no force pulling the cable from the connection terminals. Improper or loose connections can cause heat generation or fire. Do not touch, operate, or repaire the product with wet hands. Holding the plug by hand when taking out. Otherwise there is risk of electric shock or fire. Do not turn on the breaker when the front panel and cabinet are removed. Be sure to ground the air conditioner with an earthing conductor connected to the earthing terminal. Conduct repair works after checking that the refrigerating cycle section has cooled down sufficiently. Otherwise, working on the unit, the hot refrigerating cycle section can cause burns. Do not tilt the unit while removing panels. Otherwise, the water inside the unit can spill and wet floor. Do not use the welder in a well-ventilated place. Using the welder in an enclosed room can cause oxygen deficiency. Be sure to turn off power switch before connecting or disconnecting connector, or parts damage may be occur

6 Part 1 General Information 1.2 Inspections after Repair Check to see if the power cable plug is not dirty or loose. If the plug is dusty or loose it can cause an electrical shock or fire. Do not use a joined power cable or extension cable, or share the same power outlet with other electrical appliances. otherwise, it can cause an electrical shock, excessive heat generation or fire. Do not insert hands or other objects through the air inlet or outlet while the product is operating. There are sharp and moving parts that could cause personal injury. Do not block the inlet or outlet of air flow. It may cause product failure Check to see if the parts are mounted correctly and wires are connected. Improper installation and connections can cause an electric shock or an injury. Check whether the installation platform or frame has corroded. Corroded installation platform or frame can cause the unit to fall, resulting in injury. Be sure to check whether the earth wire is correctly connected. After the work has finished, be sure to do an insulation test to check whether the resistance is 2[Mohm] or more between the charge section and the non-charge metal section (Earth position). If the resistance value is low, a disaster such as a leak or electric shock is caused at user s side. Check the drainage of the indoor unit after the repair. If drainage is faulty the water may enter the room and wet floor

7 Part 1 General Information 2. menclature 2.1 Global Model Name A S W G G Code Type Code of Model Meaning 1 Production Center, A~Z L: Chang-won R22 Refrigerant A: Chang-won R410A 2 Product Type A~Z S: Split Type Air Conditioner 3 Cooling/Heating/Inverter A~Z C: Cooling Only H: Heat Pump X: C/O + E/Heater Z: H/P + E/Heater V: AC Inverter C/O N: AC Inverter H/P Q: DC Inverter C/O W: DC Inverter H/P 4, 5 Capacity 0~9 Cooling/Heating Capacity Ex. "09" 9,000 Btu/h 6 Electric Range 1~9 1: 115V/60Hz A~Z 2: 220V/60Hz 3: V/60Hz 5: V/50Hz 6: V/50Hz 7: 110V, 50/60Hz 7 Chassis A~Z Name of Chassis 8 Look A~Z Look, Color (Artcool Model) 9, 10 Function A~Z A Basic B Basic+4Way C Plasma Filter D Plasma Filter+4 Way E Tele+LCD F Tele+LCD+Nano plasma+4way G NBF F+(A/changeove)+A/clean+Low A H NBF F+(A/changeove)+A/clean+4way+Low A I Tele+LED+4way J Internet K Plasma F+4Way+Oxygen generator L NBF F+(A/changeove)+A/clean M NBF F+(A/changeove)+A/clean+4way N NBF F+(A/changeove)+A/clean+PTC P NBF F+(A/changeove)+Autoclean+4way+PTC Q NBF F+(A/changeove)+A/clean+4way+Low A+PTC R Negative ion+a/clean S (Nano)Plasma+Negative ion+a/clean T 4way+(Nano)Plasma F+Negative ion+a/clean U Nano Plasma F+4Way+(A/changeove)+A/clean+Oxygen generator V 4way+(Nano)Plasma F+Negative ion+a/clean+oxygen generator W Dry contact Y Basic + Low A 11 Serial. 1~9 LG Model Development Serial

8 Part 2 Functions & Controls 1. List of Controls & Functions Basic Mode Controls Special Mode Controls Utility Functions Protection Functions & Controls

9 Part 2 Functions & Controls 1. List of Functions & Controls Category Function Description Remark Basic mode controls Special Mode controls Utility Functions Protection Controls & Functions Cooling Mode Heating Mode Healthy Dehumidification Auto Changeover Jet Cool Jet Heat Energy saving Forced operation Auto Clean Air volume control Natural Air control Chaos Swing Sleep mode Auto control Auto Restart Function Five Second Delay (Fan) Two Minutes Stand-by (Comp.) Hot Start Freeze prevention Compressor Pre Heating Sump Heater Control Automatic Defrost Power Relay Control Inverter (with inverter power control) Overheating Protection (Power Module) Total Current Control (Over Current Protection) DC Peak Control Discharge Pipe Temp Control Low Ambient Function Oil Return Control Oil Equalizing Control Cooling operation Heating operation Dry operation Cooling mode is automatically changed to heating mode and vice verse Powerful cooling mode Powerful heating mode Air volume & set temp. are automatically selected for saving energy in cooling mode Operation without remote controller After cooling operation, this function makes the evaporator dry Indoor Fan speed Control Air volume control Program Vertical Airflow Direction control Air volume & set temp. are automatically changed for comfortable sleep When power returns after a power failure, Unit restarts in the previous operating mode For noise prevention For overload prevention To prevent cold wind blow on heating mode start Evaporator frost prevention To protect compressor To protect fan from accumulated ice at base panel Condenser frost prevention Over current prevention Modulation of voltage & frequency To protect power module To protect power device To protect power module For overheating protection For operation at low temp. To protect compressor To protect compressor NOTE: The Exploded View SVC Manual has the particular Function table for each model. Cooling Mode Only 9,12k Model Only - 9 -

10 Part 2 Functions & Controls 2. Basic Mode Controls 2.1 Cooling Mode +0.5 C(1 F) Thermo ON Setting Temp C(-1 F) Thermo OFF INV. Comp. Frequency High Low Comp. OFF High Low Operating frequency of compressor depends on the load condition, like the difference between the room temp. and the set temp., frequency restrictions. If the compressor operates at some frequency, the operating frequency of compressor cannot be changed within 30 seconds. ( not emergency conditions) Compressor turned off when - intake air temperature is in between ±0.5 C(±1 F) of the setting temp. limit for three minutes continuously. - intake air temperature reaches below 1.0 C(2 F) of the temperature of setting temp.. Compressors two minutes time delay. - After compressor off, the compressor can restart minimum 2 minutes later. 2.2 Heating Mode 5 C(9 F) 2 C(3.6 F) Thermo OFF Thermo ON Setting Temp. INV. Comp. Frequency High Low Comp. OFF High Low Comp. OFF Operating frequency of compressor depend on the load condition, The difference between the room temp. and set temp., frequency restrictions. If compressor operates at some frequency, the operating frequency of compressor cannot be changed within 30 seconds. Condition of compressor turned off - When intake air temperature reaches +5 C(9 F) above the setting temperature. Condition of compressor turned on - When intake air temperature reaches +2 C(3.6 F) above the setting temperature. * Condition of indoor fan turned off - While in compressor on : indoor pipe temp. < 20 C(68 F) - While in compressor off : indoor pipe temp. < 30 C(86 F) While in defrost control, the indoor and outdoor fans are turned off. Compressor 2minutes delay - After compressor off, the compressor can restart minimum 2 minutes later

11 Part 2 Functions & Controls 2.3 Healthy Dehumidification operation When the dehumidification operation is set by the remote controller, the intake air temperature is detected and the setting temp. is automatically set according to the intake air temperature. Intake air Temp. Setting Temp. 26 C(78.8 F) intake air temp. 25 C(77 F) 24 C(75.2 F) intake air temp.< 26 C(78.8 F) intake air temp. -1 C(-2 F) 22 C(71.6 F) intake air temp. < 24 C(75.2 F) intake air temp C(-1 F) 18 C(64.4 F) intake air temp. < 22 C(71.6 F) intake air temp. intake air temp. < 18 C(64.4 F) 18 C(64.4 F) When intake air temp. is 1 C(2 F) above the setting temp., condition of compressor is same as in cooling mode operation. When intake air temperature reaches 1 C(2 F) below the setting temp., compressor operates in step1~step3 and the indoor fan speed again operates at low speed or comes to a stop. 2.4 Auto changeover operation The air conditioner changes the operation mode automatically to keep indoor temperature steady. When room temperature vary over ±2 C(±4 F) with respect to setting temperature, air conditioner keeps the room temperature in ±2 C(±4 F) with respect to setting temperature by changing the mode from cooling to heating and vice versa. +4 C(+8 F) +2 C(+4 F) +0.5 C(+1 F) Setting Temp C(-1 F) -2 C(-4 F) Switching point Heating thermo off Cooling thermo off Switching point Mode Cooling operation Heating operation Cooling operation

12 Part 2 Functions & Controls 3. Special Mode Controls 3.1 Jet Cool operation In the heating mode or Fuzzy operation, the Jet cool function does not work. When it is input while in other mode of operation (cooling, dehumidification, ventilation), the Jet cool operation takes place. In the Jet cool mode, the indoor fan is operated at super-high speed for 30 min. at cooling mode operation. In the Jet cool mode, the room temperature is maintained at a setting temperature of 18 C(64.4 F). When the sleep timer mode is input during the Jet cool operation, the Jet cool mode has the priority. When the Jet cool button is pressed, the horizontal vane of the unit is reset to those of the initial cooling mode and then operate so that the air outflow could reach further. 3.2 Jet Heat operation While in cooling mode or Fuzzy operation, the Jet Heat function does not work. When it is input while in the Heating mode operation (dehumidification), the Jet Heat mode operation takes place In the Jet Heat mode, the indoor fan operated at super-high speed for 60 min. at Heating mode operation. In the Jet Heat mode, the room temperature is maintained at a temperature of 30 C(86 F). When the sleep timer mode is input during the Jet Heat mode operation, the Jet Heat mode has the priority. When the Jet Heat button is pressed, the horizontal vane of the unit is the unit reset to those of the initial Jet heating mode and then operates so that the air outflow could reach under flow. 3.3 Energy saving operation in cooling mode During cooling and dehumidification mode of operation, the Energy saving button can be input. In this operation, before we feel cold the set temperature and air volume is set automatically to save energy

13 Part 2 Functions & Controls 4. Utility Functions 4.1 Forced operation To operate the appliance manually in case when the remote control is lost, the forced operation selection switch is on the main unit of the appliance, and operate the appliance in the standard conditions. The operating condition is set according to the outdoor temp. and intake air temperature as follows. Indoor temp. Operating Mode Setting temp. Setting speed of indoor fan over 24 C(75.2 F) Cooling 22 C(71.6 F) 21~24 C(69.8~75.2 F) Healthy Dehumidification 23 C(73.4 F) High speed below 21 C(69.8 F) Heating 24 C(75.2 F) The unit select the last operation mode in 3 hours. Operating procedures when the remote control can't be used is as follows : - The operation will be started if the ON/OFF button is pressed. - If you want to stop operation, re-press the button. - The ON/OFF switch is on the display PCB or side of indoor unit 4.2 Auto cleaning operation Function used to perform Self Cleaning to prevent the Unit from Fungus and bad odor. Used after the Cooling Operation before turning the unit off, clean the Evaporator and keep it dry for the next operation. The function is easy to operate as it is accessed through the Remote controller. 1) Heat/pump Model 2) Cooling/only Model ON OFF ON OFF Cooling CYCLE Fan Heating Fan Cooling CYCLE Fan 13 Min 60 Sec 120 Sec Comp. ON OFF ON OFF Indoor Fan Setting Step LL LL LL Comp. Indoor Fan ON Setting Step 30 Min OFF Low

14 Part 2 Functions & Controls 4.3 Air volume control Indoor fan motor control have 6 steps. Air volume is controlled "SH", "H", "Med", "Low" by the remote controller. "LL" step is selected automatically in Hot start operation. 4.4 Natural Air Control(Auto Wind) When the Auto Step is selected and then operated, the high, medium, or low speed of the airflow mode is operated for 2~15 sec. randomly by the Chaos Simulation. Step LL L M H SH Auto Description Very low, In heating mode Low Med High Super high Natural wind 4.5 Chaos Swing By the Chaos swing key input, the horizontal vane automatically operates with the Chaos swing or it is fixed to the desired direction. 4.6 Sleep mode Auto control When the set sleep time is reached set time of [1,2,3,4,5,6,7hour] input by the remote control during the operation, the operation of the appliance stops. When the appliance is on pause, the sleep timer mode cannot be input Sleep timer operation for cooling cycle While in cooling mode, 30 min. after the start of the sleep timer, the setting temperature increases by 1 C(2. After another 30minutes lapse, it increases again by 1 C(2. Setting temp. ( C) 1.0 C(2 F) up 1.0 C(2 F) up Cooling ON temp. (Setting temp C(+1 F)) Cooling OFF temp. (Setting temp C(-1 F)) Sleep time (hour) NOTE: Some Models are different by swing width and swing pattern

15 Part 2 Functions & Controls Sleep timer operation for heating cycle While in heating mode, 60 min. after the start of the sleep timer, the setting temperature decreases by 1 C(2. After another 60minutes lapse, it decreases again by 1 C(2. Setting temp. ( C) Heating ON temp. (Setting temp) 1.0 C(2 F) down Heating OFF temp. (Setting temp C(+8 F)) 1.0 C(2 F) down 1 2 Sleep time (hr) 4.7 Auto restart When the power comes back after a sudden power failure during operation, the mode before the power failure is kept on the memory of the appliance and it automatically operates in the saved mode on the memory. Operation mode that is kept on the memory - State of operation ON/OFF - Operation mode/setting temp./selected airflow speed - Sleep timer mode/remaining time of sleep timer - Chaos Swing

16 Part 2 Functions & Controls 5. Protection Functions & Controls 5.1 Five Seconds Stand-by (fan) The indoor unit fan rotates after 5 seconds when unit is turned on. 5.2 Two Minutes Stand-by (comp.) Compressor starts two minutes later, after it is turned off 5.3 Hot start When unit starts in the heating mode to prevent cold wind blowing, the indoor fan does not rotate until the temp. of heat exchanger reaches 30 C(86 F)(model by model) 5.4 Freeze prevention (Protection of the evaporator pipe from frosting) If the indoor pipe temperaure is below 0 C(32 F) in 7 min. after the compressor operates without pause while in cooling cycle operation mode, compressor, outdoor fan are turned off. When indoor pipe temp. is 7 C(44.6 F) or higher after 2 min pause of compressor compressor, outdoor fan is turned on according to the condition of the room temperature. 6 C(42.8 F) 3 C(37.4 F) T1 Comp. Step 4 Comp. Step 2 Comp. free Comp. off Indoor pipe temp. 7 C(44.6 F) T1: 0 ~ 2 C(32~35.6 F) NOTE: Some Models are different by T

17 5.5 Compressor Preheating ,12kBtu/h Model Part 2 Functions & Controls With low outdoor temperature, It preheats the compressor to maintain the oil viscosity before the unit starts. Preheating Mode preheats the compressor motor coil by electric current without compressor running. Mode-in conditions : Outdoor temp. < 0 C (32 F) and D-pipe temp. < 15 C (59 F) Mode-out conditions : Outdoor temp. > 5 C (41 F) or D-pipe temp. < 25 C (77 F) or Compressor on , 24, 30kBtu/h Model When the unit starts with low outdoor temperature, It preheats the compressor to maintain the oil viscosity. If it is under the following conditions, the compressor runs with 15Hz for a specific time Conditions : heat sink temperature < 0 C (32 F) and D-pipe temperature < 0 C (32 F) Outdoor Temperature Running Time [sec] -5 C (23 F) ~ -0 C(32 F) C (14 F) ~ -5 C (23 F) 180 Under -10 C (14 F) Sump Heater Control (9, 12kBtu/h Model Only) With low outdoor temperature, the sump heater located on base panel prevents icing that may cause drain blockage and fan damage. Heater-on conditions : Outdoor temp. 0 C (32 F) and heating mode Heater-out conditions : Outdoor temp. > 1 C (34 F)

18 Part 2 Functions & Controls 5.5 Automatic defrost ,12kBtu/h Model While in heating mode operation in order to protect the evaporator pipe of the outdoor unit from freezing, reversed to cooling cycle to defrost the evaporator pipe of the outdoor unit. Defrosting control is available 40 minutes later since heating cycle started and the difference of the pipe temperature of outdoor unit reaches above option 1. The defrosting control is available without reference to heating operation time only if the pipe temperature of outdoor unit reaches below option 2. The mean outdoor temperature Option 1 The minimum Time of Heating(sec) Option 2-10 C(14 F) less than > ~-5 C(14~23 F) between -5~0 C(23~32 F) between >5 >5 Expected heating operating time And Heating operating time 40 minutes C(32 F) more than >5-25 Minimum Time Of Heating 5sec 5sec Main Deice time 30 sec 10 sec 1min Setting Freq. Operating Freq. Of Comp (Comp off Inapplicable.) Operating Freq. Of Comp (Comp off Applicable.) Setting Freq. 15 sec Min Min Step 5 Step 5 Min Min off Step 3 Step 3 Setting Freq. EEV Open step The Degree of Superheat Control off 300 off Starting Step 4-Way ON ON Indoor FAN Indoor FAN Setting Speed Setting Speed OFF OFF Hi Speed Hot Start Setting Speed Super low speed low speed Pre-Heat LED OFF ON OFF Deice STEP Model (kbtu/h) Compressor Frequency EEV 9 65Hz(Step 5) Hz(Step 5)

19 Part 2 Functions & Controls ,24,30kBtu/h Model Starting to the defrosting operation 1) Defrost operation will be start when the conditions below are matched a) Accumulation time of operation and the period after completion of defrost = 35 min. b) After 10 minutes from re-starting the compressor.in case of being over 35 minutes of accumulated operating time, defrosting operation starts after 10 minutes. c) Piping temperature of the outdoor heat exchanger maintain below defrost starting temperature for 4 minutes after 35 minutes continuous operation. d)in case of passing 10 minutes after oil recovery operation 2) Outdoor piping temperature is below than 6 C (21.2 F, Option) for starting defrosting operation. Defrosting Comp. Freqency Model (kbtu/h) Defrosting Comp. Frequency EEV 18 90Hz Hz Hz

20 Part 2 Functions & Controls Defrosting Control Algorithm 1) Lowering the compressor frequency when starts the defrosting operation. Constant speed compressor is ON after 10 seconds from the arrival time of 30 Hz (Option) frequency and is speed up its revolution till 100 Hz (Option) 2) Every EEV have 350 pulse (Option) of opening when starts defrosting operation. 3) Reversing valve is OFF after 5 seconds from arriving the compressor operating frequency of 30 Hz and then fans of indoor units turn OFF.(including the indoor unit with being OFF except the remote controller is being OFF) 4) After 5 seconds from the time arriving 30 Hz, fans of outdoor unit turn OFF and Hot Gas bypass/oil separator valve turn ON. NOTE: Comp.frequency and EEV pulse is different each models. Control algorithm of defrost completion 1) Frequency of compressor lowering to 30 Hz and maintain constant speed operation with 30 Hz for 75 seconds and then stating operation. If the constant speed compressor is OFF, it will be receive OFF signal after 5 seconds from the arrival time of 30 Hz. 2) The EEV will open with the standard previous pulse after 5 seconds from the time of 30 Hz. 3) Reversing valve is ON after 15 seconds from the time of 30 Hz of compressor frequency. 4) Fan of outdoor unit is ON with high speed and maintain it after 5 seconds from the time of 30Hz. 5) Hot Gas bypass valve/oil separator bypass valve make OFF after 75 seconds from the time of 30Hz. NOTE: Comp.frequency and EEV pulse is different each models

21 Part 2 Functions & Controls 5.6 Power Relay Control Power relay turns on 1 second later after the power is supplied to the outdoor unit. Control sequence : power on PTC operating power relay on 5.7 Inverter U V W + U V W 3Ø Comp. Motor 1. The single phase power AC is converted into DC. 2. The single phase power DC is converted into a three phase chopped DC voltage with a variable frequency. 3. When the frequency changes, the rotation speed of the compressor changes resulting in an changed refrigerant circulation. This leads to changeable amount of the heat exchange per unit

22 Part 2 Functions & Controls 5.8 Overheating Protection (Power Module) ,12kBtu/h Model If the temperature of the heat sink thermistor. reaches over Toff, the Compressor stop instantly. The compressor operating frequency is limited according to the heat sink thermistor. (refer to below FIG.) It will blink 4 times, when the thermistor is open or short, also when the temperature is over T off. T off C T = (T off - T on)/3 T1 = T on + T T2 = T on + 2 * T Heat Sink Temp. T2 C T1 C T on C COMP Freq. Free Fc-1 Fc-2 Fc-1 Fc-2 OFF Free T on : 85 C(185 F) (Model by Model) T off : 95 C(203 F) (Model by Model)

23 Part 2 Functions & Controls ,24,30kBtu/h Model Function : Power module failure protection by checking the temperature of heat sink. There is a temperature sensor for checking the heat sink temperature. Heat sink sensor failure error Short Check : if temperature 130 C(266 F) Open Check : if temperature < - 30 C(-22 F) System will go in self diagnosis (Error code 65) is displayed and product stops. Heat sink temperature control a) Heat sink temperature < T2 : limitation on compressor frequency b) T2 heat sink temperature < Toff : Compressor frequency down by 5 Hz c) Heat sink temperature Toff : Compressor will be off. System will stop if this situation occurs 5 times in 1 hour and error code will be generated also self diagnosis will start. If high temperature situation occurs 5 times in 1 hr system counts 1 error and after that 4 times if this situation occurs system stops and give error code. If the temperature reached Toff condition system will count 5 times after that and system will stop with error code. Toff=85 C(185 F) Heat Sink temp T2=75 C(167 F) T1=70 C(158 F) COMP Hz Set frequency 5 Hz Down Set frequency 5 Hz Down OFF Set frequency

24 Part 2 Functions & Controls 5.9 Total Current Control (Over Current Protection) ,12kBtu/h Model 1) CT1 control If the operating current reaches I1, the operating frequency of the compressor decreases. After decreasing the operating frequency by 1step, if operating current is below I1 for 60 seconds continuously, the operating frequency of compressor increases by 1step. 2) CT2 control If the operating current of the appliance reaches I2, the compressor stop instantly and two minutes later the compressor restarts again. If CT2 occurs 5 times within one hour, the appliance turn off and displays ERROR CODE 7. Model CT 1 CT 1 (kbtu/h) (Cooling) (Heating) CT A 9A 10A A 9A 10A

25 Part 2 Functions & Controls ,24,30kBtu/h Model 1) Detection : check the output DC voltage of Current Transformer(CT). 2) Current Transformer Sensing Error a) In initial power input, if the CT output is over 4.0V (25A) it shows. Error Code 40 (defect in CT sensing) 3) CT 1 detection : a) If total current exceeds CT1 value.reduce 1 step of operating Hz. - Step down 10Hz from current step. - If new Hz is below the minimum frequency 15Hz, then turn off the compressor. b) After step down,if the total current exceed 1 for more than 5 sec. then step down 1 more step. c) If the current continue below 1 for more than 1 min.,return the Hz to setting Hz. 4) CT 2 detection : a) If total current exceeds CT2 turn off compressor. And after 3 min turn on the compressor and check the current again. b) If CT2 occurs 5 times in 1 hour,stop the operation and shows Error Code 22 Model CT 1 CT 1 (kbtu/h) (Cooling) (Heating) CT A 12A 14A 24 14A 12A 15.5A 30 11A 12A 14A

26 Part 2 Functions & Controls 5.10 DC Peak control DC Peak Current Error by a fault signal of IPM If the operating current of IPM reaches 35A 3A, the compressor stops instantly. If DC PEAK occurs 5 times within 1 hour, the appliance turns off and displays Error Code 6(9,12kBtu/h Model) / Error Code 21(18,24,30kBtu/h Model) DC Peak Current Error by the compressor lock If the DC LINK voltage below DC 140V occurs 5 times within 1 hour while the compressor is operating, the appliance turns off and display Error Code 6(9k,12k Model) / Error Code 23(18k,24k,30k Model) DC Peak Current Error by the Outdoor Fan Lock If this problem occurs 5 times within 1 hour in case of the temperature of outdoor pipe TH is over 65 C(149 F) while the compressor is operating, the appliance turns off and displays Error Code 6(9,12kBtu/h Model) / Error Code 61(18,24,30kBtu/h Model) Discharge Pipe Temp Control ,12kBtu/h Model If the temperature of the discharge pipe of compressor reaches over 130 C(266 F) or below -30 C(-22 F) the compressor stops instantly. The compressor operating frequency is limited according to the compressor dome TH. (Refer to below Fig.) Temperature range of COMP SPEC varies by 10 C(50 F). T off C T3 C D-Pipe Temp. T = (T off - T2)/2 T1 = T2-2 * T T3 = T2 + T T2 C T1 C -13 C(8.6 CF) COMP Freq. Fh min Free Fc-1 Fc-2 OFF Fc-2 Fc-1 Free T off : 110 C(230 F) T2 : 100 C(212 F)

27 Part 2 Functions & Controls Inverter Compressor (18,24,30kBtu/h Model) 1) There can be two situations (a) Sensor is failed (Error Code 41) (b) Abnormal high temperature discharge temperature (error code for high discharge will be generated) Both cases unit will stop. 2) Compressor working (a) If discharge pipe temperature T1 limitation on compressor frequency (b) T2 discharge pipe temperature T off (Hysteresis control) Compressor frequency down by 5Hz and expansion valve up by 10 pulse in every 1 min. (c) Discharge pipe temperature Toff Compressor will be off System will stop if this situation occurs 5 times in 1 hour and error code will be generated. Toff(105) C(221 F) D-Pipe temp T2(95) C(203) F T1(90) C(194) F COMP Hz Set 5 Hz Down Set 5 Hz Down OFF Expansion valve Set 10 Pulse Up Set 10 Pulse Up Stop control Set

28 Part 2 Functions & Controls Constant Compressor (only 30kBtu/h Model) 1) There can be two situations (a) Sensor is failed (Error Code 41) (b) Abnormal high temperature discharge temperature (error code for high discharge will be generated) Both cases unit will stop. 2) Compressor working (a) If discharge pipe temperature < T1 Compressor ON, EEV on-time control (b) T2 discharge pipe temperature < Toff (Hysteresis control) Expansion valve up by ßpulse every 1 min. If EEV is in the starting control it will follow it as it is. (c) Discharge pipe temperature Toff Compressor will be OFF System will stop if this situation occurs 5 times in 1 hour and error code will be generated (Error Code 33). Toff(105) C(221) F D-Pipe temp T2(95) C(203) F T1(90) C(194) F COMP Step ON OFF ON Expansion valve On-time control 10 Pulse Up Stop On time control

29 Part 2 Functions & Controls 5.12 Low Ambient control ,12kBtu/h Model If outdoor temperature drops below certain temperature, liquid back is prevented by On/Off control of outdoor fan. It can prevent frosting of evaporator and keep cooling operation Model Mode-in by outdoor pipe temp. Mode-in Condition Outdoor fan-on time 3 min. (And) Outdoor pipe temp. 4 C (39 F) (And) Outdoor temp. < 10 C (50 F) Mode-out Condition Outdoor fan-off time 5 min. (Or) Outdoor pipe temp. 20 C(68 F) (And) Outdoor temp. 10 C (50 F) Mode-in by indoor pipe temp. Comp-on time 5 min. (And) Indoor pipe temp. 4 C (39 F) (And) Outdoor temp. < 10 C (50 F) Outdoor fan-off time 5 min. (Or) Indoor pipe temp. 4 C (39 F) (And) Outdoor temp. 10 C (50 F) , 24, 30kBtu/h Model Low ambient cooling case : In this situation outdoor fan works in ON/OFF control. : If the pipe temperature 0 C(32 F) and it is falling rapidly in that case compressor will run for 5 min & then it will go in low ambient control. ( Temp. value can be different for each model.) After the system is stopped by CT cut or heat sink cut-off then the cycle returns to the normal condtiond control. (T2 = 0) C Outdoor pipe temp (T1 = 0) C O/D fan Set speed Off Set speed Off Set speed Model T1 [ C( F)] T2 [ C( F)] 18kBtu/h 18(64) 18 24kBtu/h 16(61) 16 30kBtu/h 0(32)

30 Part 2 Functions & Controls 5.13 Oil return control(30kbtu/h Model) Operating Contion 1) When the continuous running time is over 3hr.(option), oil returning operation is made for 3min. In case of the initial operation, oil returning operation is made, after completing initial operation. 2) After defrost and oil returning operation, the continuous running time is resetted Operation Process 1) EEV-Full open, Hot gas bypass valve-on 2) Compressor Step-70Hz + Constant Comp. On(Option) 3) Reversing valve-off(process of Off/On, follows defrost operating.) 4) Outdoor Fan-Low step 5.14 Oil equalizing control(30kbtu/h Model) Operating condition : 1) When the continuous inverter compressor running time at under 40 Hz(option) is over 2 hours(option) in 2 compressor system, oil restoring operation is made. 2) If compressor operating Hz is below 40 Hz by the safety control, the accumulated time will be cleared and oil restoration is not made. 3) During this operation,if operating Hz couldn t be changed by safety control,stop this operation. Operating process : Raise the operating HZ up to 70,and after 20 sec.(option) recover to the last value

31 Part 3 Test Run Part 3 Test Run 1. Check before Test Run Test Run Flow chart Test Run Detail

32 Part 3 Test Run 1. Check before Test Run 1 Check to see whether there is any refrigerant leakage, and check whether the power or transmission cable is connected properly. 2 Check whether the liquid pipe and gas pipe valves are fully opened. NOTE: Be sure to tighten caps. Confirm that 500 V megger shows 2.0 MΩ or more between power supply terminal block and ground. Do not operate in the case of 2.0 MΩ or less. 3 NOTE: Never carry out mega ohm check over terminal control board. Otherwise the control board may break. Immediately after mounting the unit or after leaving it turned off for an extended length of time, the resistance of the insulation between the power supply terminal board and the ground maydecrease to approx. 2.0 MΩ as a result of refrigerant accumulation in the internal compressor. If the insulation resistance is less than 2.0 MΩ, turn on the main power supply

33 Part 3 Test Run 2. Test Run Flow chart START Test operation for indoor unit Operate the unit in cooling mode. Does Test operation start? Yes Is cold air discharged for more than 3 minutes? Yes Is there any temperature difference between intake and discharged air? Yes Is the operating current normal? Yes Operation mode change to Heating mode Refer to part4, 7 Electric part Refer to part4, 5 Cycle part * Check the load (In/Out Temp.) * Check pipe length and amount of refrigerant * Check for abnormal sound in outdoor unit (comp.,fan, others ) Is hot air discharged? After Hot Start Yes rmal Refer to Troubleshooting Guide NOTE: When outdoor temperature is low,the unit is operated to Heating mode

34 Part 3 Test Run 3. Test Run Detail 1. Check that all tubing and wiring have been properly connected. 2. Check that the gas and liquid side service valves are fully open. Settlement of outdoor unit Anchor the outdoor unit with a bolt and nut(ø10mm) tightly and horizontally on a concrete or rigid mount. When installing on the wall, roof or rooftop, anchor the mounting base securely with a nail or wire assuming the influence of wind and earthquake. In the case when the vibration of the unit is conveyed to the hose, secure the unit with an anti-vibration bushing. Bolt Tubing connection Evaluation of the performance Operate unit for 15~20 minutes, then check the system refrigerant charge: 1. Measure the pressure of the gas side service valve. 2. Measure the temperature of the intake and discharge air. 3. Ensure the difference between the intake temperature and the discharge is more than 8 C(46 F) (Cooling) or (Heating). Discharge air Intake temperature NOTE: If the actual pressure is higher than shown, the system is most likely over-charged, and charge should be removed. If the actual pressure are lower than shown, the system is most likely undercharged, and charge should be added. The air conditioner is now ready for use. PUMP DOWN This is performed when the unit is to be relocated or the refrigerant circuit is serviced. Pump Down means collecting all refrigerant in the outdoor unit without loss in refrigerant gas. CAUTION: Be sure to perform Pump Down procedure with the unit in cooling mode. Pump Down Procedure 1. Connect a low-pressure gauge manifold hose to the charge port on the gas side service valve. 2. Open the gas side service valve halfway and purge the air from the manifold hose using the refrigerant gas. 3. Close the liquid side service valve(all the way in). 4. Turn on the unit's operating switch and start the cooling operation. 5. When the low-pressure gauge reading becomes 1 to 0.5kg/cm 2 G(14.2 to 7.1 P.S.I.G.), fully close the gas side valve stem and then quickly turn off the unit. At that time, Pump Down has been completed and all refrigerant gas will have been collected in the outdoor unit. 5. Check operating current. 6. Change operation mode and check. Discharge temperature 4. For reference; the gas side pressure of optimum condition is as below.(cooling) Refrigerant Outside ambient TEMP. The pressure of the gas side service valve. R22 35 C (95 F) 4~5kg/cm 2 G(56.8~71.0 P.S.I.G.) R410A 35 C (95 F) 8.5~9.5kg/cm 2 G(120~135 P.S.I.G.)

35 Part 4 Trouble Shooting Part 4 Trouble Shooting 1. 2-Way, 3-Way Valve Pumping Down Evacuation (All amount of refrigerant leaked) Gas Charging (After Evacuation) Cycle Troubleshooting Guide Electronic Parts Troubleshooting Guide Self-diagnosis Function

36 Part 4 Trouble Shooting 1. 2-Way, 3-Way Valve 2-way Valve (Liquid Side) 3-way Valve (Gas Side) Flare nut To piping connection To outdoor unit Hexagonal wrench (4mm) Open position Closed position Flare nut To piping connection Valve cap Open position Closed position Service port cap To outdoor unit Pin Service port Works Shipping Air purging (Installation) Operation Pumping down (Transfering) Evacuation (Servicing) Gas charging (Servicing) Pressure check (Servicing) Gas releasing (Servicing) Shaft position Shaft position Service port Closed Closed Closed (with valve cap) (with valve cap) (with cap) Open Closed Open (counter-clockwise) (clockwise) (push-pin or with vacumm pump) Open Open Closed (with valve cap) (with valve cap) (with cap) Closed Open Open (clockwise) (counter-clockwise) (connected manifold gauge) Open Open Open (with charging cylinder) Open Open Open (with charging cylinder) Open Open Open Open Open (with charging cylinder) Open (with charging cylinder)

37 Part 4 Trouble Shooting 2. Pumping Down Indoor unit Liquid side 2-Way valve Open Outdoor unit Gas side 3-Way valve Closed CLOSE Purge the air Lo CLOSE Procedure (1) Confirm that both the 2-way and 3-way valves are set to the open position. Remove the valve stem caps and confirm that the valve stems are in the raised position. Be sure to use a hexagonal wrench to operate the valve stems. (2) Operate the unit for 10 to 15 minutes. (3) Stop operation and wait for 3 minutes, then connect the charge set to the service port of the 3-way valve. Connect the charge hose with the push pin to the service port. (6) Operate the air conditioner at the cooling cycle and stop it when the gauge indicates 1kg/cm 2.g. (7) Immediately set the 3-way valve to the closed position. Do this quickly so that the gauge ends up indicating 3 to 5kg/cm 2.g. (8) Disconnect the charge set, and mount the 2- way and 3-way valve s stem nuts and the service port nut. Use torque wrench to tighten the service port nut to a torque of 1.8 kg.m. Be sure to check for gas leakage. (4) Air purging of the charge hose. Open the low-pressure valve on the charge set slightly to air purge from the charge hose. (5) Set the 2-way valve to the closed position

38 Part 4 Trouble Shooting 3. Evacuation (All amount of refrigerant leaked) Indoor unit Liquid side 3-Way valve Open Outdoor unit Gas side 3-Way valve Open Vacuum pump OPEN Lo OPEN Vacuum Gage Procedure (1) Connect the vacuum pump to the center hose of charge set center hose (2) Evacuation for approximately one hour. Confirm that the gauge needle has moved toward 0.8 Torr. (3) Close the valve (Lo side) on the charge set, turn off the vacuum pump, and confirm that the gauge needle does not move (approximately 5 minutes after turning off the vacuum pump). (4) Disconnect the charge hose from the vacuum pump. Vacuum pump oil. If the vacuum pump oil becomes dirty or depleted, replenish as needed

39 Part 4 Trouble Shooting 4. Gas Charging (After Evacuation) Indoor unit Liquid side 3-Way valve Open Outdoor unit Gas side Charging cylinder Check valve 3-Way valve Open (1) OPEN Lo CLOSE Vacuum Gage Procedure (1) Connect the charge hose to the charging cylinder. Connect the charge hose which you dis-connected from the vacuum pump to the valve at the bottom of the cylinder. If you are using a gas cylinder, also use a scale and reverse the cylinder so that the system can be charged with liquid. (2) Purge the air from the charge hose. Open the valve at the bottom of the cylinder and press the check valve on the charge set to purge the air. (Be careful of the liquid refrigerant). The procedure is the same if using a gas cylinder. (3) Open the valve (Lo side on the charge set and charge the system with liquid refrigerant. If the system can not be charged with the specified amount of refrigerant, it can be charged with a little at a time (approximately 150g each time) while operating the air conditioner in the cooling cycle; however, one time is not sufficient, wait approximately 1 minute and then repeat the procedure (pumping down-pin). This is different from previous procedures. Because you are charging with liquid refrigerant from the gas side, absolutely do not attempt to charge with larger amounts of liquid refrigerant while operating the air conditioner. (4) Immediately disconnect the charge hose from the 3-way valve s service port. Stopping partway will allow the gas to be discharged. If the system has been charged with liquid refrigerant while operating the air conditioner turn off the air conditioner before disconnecting the hose. (5) Mount the valve stem nuts and the service port nut. Use torque wrench to tighten the service port nut to a torque of 1.8 kg.m. Be sure to check for gas leakage

40 Part 4 Trouble Shooting 5. Cycle Troubleshooting Guide Trouble analysis 1. Check temperature difference between intake and discharge air, and operating current. Temp. Difference Operating Current Temp. difference Current Temp. difference Current Temp. difference Current : approx. 0 C(1 F) : less than 80% of rated current : approx. 8 C(16 F) : less than 80% of rated current : less than 8 C(16 F) : near the rated current All amount of refrigerant leaked out. Check refrigeration cycle. Refrigerant leakage Clog of refrigeration cycle Defective compressor Excessive amount of refrigerant Temp. difference : over 8 C(16 F) rmal NOTICE Temperature difference between intake and discharge air depends on room air humidity. When the room air humidity is relatively higher, temperature difference is smaller. When the room air humidity is relatively lower temperature difference is larger

41 Part 4 Trouble Shooting 6. Electronic Parts Troubleshooting Guide Trouble 1 The Product doesn t operate at all. (9~30kBtu/h Model) Turn off the main power and wait until LED on outdoor PCB is off. Turn on the main power again. Does "Beeping" sound is made from the indoor unit? Does "Lighting" LED is mounted on the outdoor PCB? NO Check the voltage of power(ac 208~230V, 60Hz). The voltage of main power. The voltage applied to the unit. The connecting method of Indoor/Outdoor connecting cable (each color) The P.W.B. Ass'y (Fuse,ise Filter, Power Module(SMPS), IC01D,IC04D) YES Primarily, the operating condition of Micom is O.K. Check CN-DISP1 The operation check of the P.C.B. Ass'y Procedure Specification Remedy 1) The input voltage of Power Module(SMPS) 2) The output voltage of Power Module (SMPS) 3) IC01D(LD1085), IC04D(7805) : DC 220V~390V : 15V 10% : DC 5V Replace the P.C.B

42 Part 4 Trouble Shooting Trouble 2 Product doesn't operate with the remote controller. (9~30kBtu/h Model) Turn on main power. While the compressor has been stopped, the compressor does not operate owing to the delaying function for 2 minutes after stopped. When the compressor stopped Indoor Fan is driven by a low speed. At this point the wind speed is not controlled by the remote controller. (When operated in the Sleeping Mode, the wind speed is set to the low speed as force).) Caused by the remote controller. Caused by other parts except the remote controller When the mark ( ) is displayed in LCD screen, replace battery. Check the contact of CN-DISP 1, 2 connector Check DISP P.C.B Ass'y -Voltage between CN-DISP1 - : DC +5V Check point Check the connecting circuit between MICOM PIN and CN-DISP1 PIN Check receiver ass'y

43 Part 4 Trouble Shooting Trouble 3 The Compressor/Outdoor Fan don't operate (9, 12kBtu/h Model) Turn on the main power. Operate Cooling Mode by setting the disired temperature of the remote controller is less than one of the Indoor temperature by 1 C at least. When in air circulation mode, compressor/outdoor fan is stopped. Check the sensor for Indoor temperature is attatched as close as to be effected by the themperature of Heat Exchange (EVA.) When displaying Error code, refer to the trouble shooting guide. Check the main power source.(ac 208V~230V) Check the trouble shooting guide error code 6,9 Turn off main power. Check the electrical wiring diagram of Outdoor side. Check the open or short of connecting wires between Indoor and Outdoor

44 Part 4 Trouble Shooting Trouble 4 The Compressor/Outdoor Fan don't operate (18, 24, 30kBtu/h Model) Turn on the main power. Operate Cooling Mode by setting the disired temperature of the remote controller is less than one of the Indoor temperature by 1 C at least. When in air circulation mode, compressor/outdoor fan is stopped. Check the sensor for Indoor temperature is attatched as close as to be effected by the themperature of Heat Exchange (EVA.) When displaying Error code, refer to the trouble shooting guide. Check the main power source.(ac 208V~230V) Check the trouble shooting guide error code 21,26. Check that CN_FAN(A,B) supplied voltage to outdoor PCB is about AC 208V~230V. Turn off main power. Check the electrical wiring diagram of Outdoor side. Check the open or short of connecting wires between Indoor and Outdoor

45 Part 4 Trouble Shooting Trouble 5 When indoor Fan does not operate.(9~30kbtu/h Model) Turn off main power. Check the connection of CN-FAN. Check the Fan Motor. Check the Fuse(AC250V, T2A). Check the related circuit of indoor Fan Motor. The pin. 38 of micom and the part for driving SSR.(Q01M) Check the related pattern. Check the SSR. - SSR Open: Indoor Fan Motor never operate. - SSR short: Indoor Fan Motor always operates in case of ON or OFF. Turn on the main power Check the SSR high speed operation by remote control. (the Indoor Fan Motor is connected) The voltage of Pin 1(orange) and 3(black) of CN-FAN. About AC 160V over About AC 50V over SSR is not damaged Check SSR

46 Part 4 Trouble Shooting 7. Self-diagnosis Function Error Indicator The function is to self-diagnoisis airconditioner and express the troubles identifically if there is any trouble. Error mark is ON/OFF for the operation LED of evaporator body in the same manner as the following table. If more than two troubles occur simultaneously, primarily the highest trouble fo error code is expressed. After error occurrence, if error is released, error LED is also released simultaneously. To operate again on the occurrence of error code, be sure to turn off the power and then turn on. Having or not of error code is different from Model. 9, 12kBtu/h Model Error Code Error Indicator Cause of Error Display Indoor Outdoor Indoor Operation 1 1 time 1time 1time 1time 1time 3 sec 3 sec 3 sec 3 sec Indoor Temp. sensor error - Sensor open or short O ON 2 2 times 2 times 2 times 2 times 3 sec 3 sec 3 sec Outdoor Temp. sensor error - Sensor open or short O O ON 4 4 times 4 times 3 sec 3 sec Heat Sink sensor error - Sensor open or short - Heat Sink temp is over 95 O O ON 5 5times 3 sec 5times 3 sec Communication error O O OFF 6 6times 3 sec 6times DC Peak error O O SHUT DOWN 7 7times 3 sec 7times Over current error (CT2) O O SHUT DOWN 8 8times 3 sec 8times Indoor fan lock error (BLDC fan model only) O OFF 9 9times 3 sec 9times Outdoor fan lock error (BLDC fan model only) O O OFF 10 times 10 times 10 D-Pipe TH. is short or open. O O ON 3 sec (4 LED Model)

47 Part 4 Trouble Shooting 18,24,30kBtu/h Model Indoor Error Error code Descrition INV TPS LED1 LED2 Indoor (Red) (Green) Status 00 Error ON 01 Indoor Room themistor error 1time OFF 02 Indoor in-piping sensor error 2times OFF 05 Communcation error between in and out 5times OFF 06 Indoor Out-Piping sensor error 6times OFF Outdoor Error Ex) Error Code 21 (IPM Fault) 2 Times 2 Times 2 Times LED01G (RED) 1 Sec. 1 Sec. 1 Sec. 1 Time 1 Time 1 Time LED02G (GREEN) 2 Sec. 2 Sec. Error code Contents LED01G (Red) LED02G (Green) Case of error Outdoor Status 21 IPM Fault (Compressor Over current) 2 times 1 time Compressor malfunction,ipm Fault Off 22 CT 2(Max. Current) 2 times 2 times Current is 14A Off 23 DC Link Low Volt. 2 times 3 times DC Link volt. Is 140V Off 24 Low / High press 2 times 4 times Low / High press switch OPEN Off 25 AC Low / AC High Volt. 2 times 5 times Abnormal AC volt. Input. Off 26 DC Compressor Position 2 times 6 times Off 27 PSC Fault 2 times 7 times Off 28 DC Link High Volt 2 times 8 times Off Off 32 Discharge Pipe Temp. High (INV) 3 times 2 times Off Off 33 Discharge Pipe Temp. High (Cons.) 3 times 3 times Off Off

48 Part 4 Trouble Shooting Error code Contents LED01G (Red) LED02G (Green) Case of error Outdoor Status 40 CT Circuit (open/ short) 4 times CT Circuit malfunction Off 41 D-pipe sensor INV. (open/ short) 4 times 1 time Open / Short Off 44 Air sensor (open/ short) 4 times 4 times Open / Short Off 45 Cond. Pipe sensor (open/ short) 4 times 5 times Open / Short Off 46 Suction pipe sensor (open/ short) 4 times 6 times Open / Short Off 47 D-pipe sensor Cons. (open/ short) 4 times 7 times Open / Short Off 53 Communication (Indoor Outdoor) 5 times 3 times Communication Poorly Off 60 EEPROM check sum 6 times Check sum mismatching Off 61 Cond. Pipe sensor temp. high 6 times 1 time Cond. Temp. high Off 62 Heat sink sensor temp. high 6 times 2 times Heat sink temp. high Off 65 Heat sink sensor (open/ short) 6 times 5 times Open / Short Off

49 Part 4 Trouble Shooting Troubleshooting Guide(9,12kBtu/h Model) Error code 1 Description Indoor TH. is short or open Cause of error Indoor TH. (sensor) is short or open Indoor TH. (sensor) is not connected to the indoor pcb assembly Damage or defect on the sensing circuit of indoor pcb assembly. (R01H, R02H, R03H, R04H, C01H, C02H) Check flow YES YES Indoor TH. is connected to Indoor pcb assembly? Indoor TH. is right? Sensing circuit of indoor pcb is right? - Connect to CN-TH1 in indoor pcb assembly Check Indoor TH. - Measure resistance of TH. (air : about 10kΩ at 25 C(77 F), pipe : about 5kΩ at 25 C(77 F) - Check soldering state of R01H ~ R04H, C01H, C02H Error code 2 Description Outdoor TH. is short or open Cause of error Outdoor TH. (sensor) is short or open Outdoor TH. (sensor) is not connected to the outdoor pcb assembly Damage or defect on the sensing circuit of outdoor pcb assembly. (R03H~R06H, C02H, C03H) Check flow YES YES Outdoor TH. is connected to outdoor pcb assembly? Outdoor TH. is right? Sensing circuit of outdoor pcb is right? - Connect to CN-TH1 in outdoor pcb assembly Check outdoor TH. - Measure resistance of TH. (air : about 10kΩ at 25 C(77 F), pipe : about 5kΩ at 25 C(77 F) - Check soldering state of R03H ~ R06H, C02H, C03H

50 Part 4 Trouble Shooting Error code 4 Description Heat-sink Temp. is over 95 C(203 F) Heat-sink TH. is open or short Cause of error Heat-sink TH. is damaged(short or open). Heat-sink Temp. is over 95 C(203 F) Damage or defect on the sensing circuit of outdoor pcb assembly. (R01H, R02H, C01H) Check flow YES YES Heat-sink TH is connected to outdoor PCB assembly? Heat-sink TH. in INV-IC is Right? Sensing circuit of outdoor pcb is right? - Connect to CN-TH2 in outdoor PCB assembly Check heat-sink TH. - Measure resistance of TH. (about 10kΩ at 25 C(77 F)) - Check soldering state of R01H, R02H, C01H 9k,12kBtu/h Model Heat-sink Thermistor resistans check R-T Graph Ω Resistance[kΩ] Temperature[ C]

51 Error code 5 Description Communication Error Cause of error Part 4 Trouble Shooting Wrong or missing wiring between indoor and outdoor unit cable Defect of communication components in indoor pcb assembly Defect of communication components in outdoor pcb assembly Defect of power supply components in outdoor pcb assembly ground connection in air conditioner unit (affected by noise in power source) Check flow Wiring connection Is right? YES Is the voltage of T/Block, in outdoor about AC 208~230V? YES Is the voltage of GND & DC5V in Outdoor pcb about DC 5V? Indoor Outdoor 1(BR) 1(BR) 2(BL) 2(BL) 3(GN/YL) 3(GN/YL) 4(RD) 4(RD) Check power connector Is not connected to the T/Block in indoor unit. Check FUSE, NF01/02J, PTC, Power Module, BD-01S in Outdoor pcb assembly YES YES Communication circuit of indoor & outdoor pcb Is right? Ground connection is installed? (power outlet or outdoor chassis) Earth port Check IC01K, IC02K,D01K~D03K, ZD01K~ZD03K, R01K~R10K, C01K~C04K Install ground connection from outdoor unit. (In case power outlet has no earth port)

52 Part 4 Trouble Shooting Error code 6 Description DC Peak Error Cause of error Supplied power is not normal Comp Connector (CN-U,V,W) is disconnected or inserted to wrong position Compressor is damaged (coil short) replace compressor Too much Refrigerant Defect in outdoor pcb assembly replace pcb assembly Check flow Supplied voltage to Outdoor pcb is about AC 208~230V? YES Is connector (CN-U,V,W) connected to compressor and inserted to pcb in right position? YES Refrigerant pressure is right? Check power source Check CN-U,V,W connector (U : RD, V : BL, W : YL) Check refrigerant pressure and adjust. YES YES Is the compressor right? Inverter components in outdoor pcb assembly are right? Check resistance Between U-V, V-W, U-W port. Short / Open circuit (Comp.motor coil error) normal : 1 ~2Ω Between U,V,W and Body normal : over 10MΩ * 9 K/12K Model Check Short of SPM3 pins (GND - P, U, V, W pin) Direction of D01Z~D03Z, C08Z,10Z,12Z,16Z Assembling state of R01P ~ R21P & IC01P Assembling state of screw between INV-IC & Heat-sink DC 15V output of Power module. U Ω V W

53 Error code 7 Description Over current Error (CT2) Cause of error Part 4 Trouble Shooting Supplied power is not normal Indoor/outdoor fan is locked Too much refrigerant Defect in current sensing circuit in outdoor pcb assembly Check flow Supplied voltage to Outdoor pcb is about AC 208~230V? YES Does indoor / outdoor fan work normally? YES Refrigerant pressure is right? Check power source Check indoor / outdoor fan and adjust. Check refrigerant pressure and adjust. YES Current sensing circuit is right? Check current sensing circuit. - check CT is damaged in outdoor pcb (output wire is disconnected to pin or not) - BD01N is inserted in right position (refer marking on pcb and component) - Spec of R01N (1kΩ), R02N (1.65kΩ) is correct - Direction of diode (D01N, D02N) is right

54 Part 4 Trouble Shooting Error code 8 Description Indoor fan is locked (BLDC fan model only) Cause of error Indoor fan is locked or separated Fan connector is not connected to indoor pcb assembly Defective in DC-fan driving circuit Check flow YES YES Indoor fan is rotating? (1) Indoor fan is rotating? (2) DC fan driving circuit is right? Check indoor unit - remove obstacles in indoor unit - fan assembled correctly. Check soldering state of CN-Motor1 & assembling state of DC Fan connector Check DC Fan Driving circuit (Soldering state & Direction) - R01F~R09F, C01F~C03F, IC01F~IC03F, Q01F~Q02F, ZD01F Error code 9 Description Outdoor fan is locked (BLDC fan model only) Cause of error Outdoor fan is locked by an obstacle (ex : branch of tree, bar etc) Fan connector is not connected to outdoor pcb assembly Defective in DC-fan driving circuit Check flow YES YES Outdoor fan is rotating? (1) Outdoor fan is rotating? (2) DC fan driving circuit is right? Check outdoor unit - remove obstacles in outdoor unit Check connector is not connected to outdoor pcb assembly (CN-FAN2) Check DC Fan driving circuit (Soldering state & Direction) - R01F~R05F, C01F~C03F, Q01F~Q04F, ZD01F

55 Error code 10 Description D-Pipe TH. is short or open Cause of error Part 4 Trouble Shooting D_pipe TH. is short or open D_pipe TH. is not connected to the outdoor pcb assembly Damage or defect on the sensing circuit of outdoor pcb assembly Check flow YES YES D_PIPE TH. is connected to Outdoor pcb assembly? D_PIPE TH. is right? Sensing circuit of outdoor pcb is right? Connect to CN-D_PIPE in outdoor pcb assembly Check D_PIPE TH. - Measure resistance of TH. (about 200kΩ at 25 C(77 F)). - Check soldering state of R07H, R08H, C04H

56 Part 4 Trouble Shooting Troubleshooting Guide(18,24,30kBtu/h Model) 1) Troubleshooting CH01, CH02, CH06 Error code Title Cause of error Check point & rmal condition 01 Indoor air sensor Open / Short Soldered poorly Internal circuit error rmal resistor : 10kΩ/ at 25 C(77 F) (Unplugged) rmal voltage : 2.5VDC / at 25 C(77 F) (plugged) 02 Indoor inlet pipe sensor Open / Short Soldered poorly Internal circuit error rmal resistor : 5kΩ/ at 25 C(77 F) (Unplugged) rmal voltage : 2.5VDC / at 25 C(77 F) (plugged) 06 Indoor outlet pipe sensor Open / Short Soldered poorly Internal circuit error rmal resistor : 5kΩ/ at 25 C(77 F) (Unplugged) rmal voltage : 2.5VDC / at 25 C(77 F) (plugged) 10kΩ 2.5VDC Ω V Check the resistance Check the voltage Check Point 1. Unplug the sensor on Indoor unit PCB. 2. Estimate the resistance of each sensor. 3. If the resistance of the sensor is 10kΩ/ 5kΩ at 25 C(77 F), then sensor is normal. 4. If the resistance of the sensor is 0 kω or, then sensor is abnormal. Change the sensor. 5. Plug the sensor on Indoor unit PCB and Power ON. 6. Estimate the voltage of each sensor. 7. If the voltage of the sensor is 2.5VDC at 25 C(77 F), then sensor is normal. 8. If the resistance of the sensor is 0 or 5VDC, then sensor is abnormal. Repair or Change the PCB

57 Part 4 Trouble Shooting 2) Troubleshooting CH05, CH53 Error code 05 / 53 Title Cause of error Check point & rmal condition Communication (Indoor Outdoor) Communication poorly Power input AC 208~230V. (Outdoor, Indoor) The connector for transmission is disconnected. The connecting wires are misconnected. The GND1,2 is not connected at main GND. The communication line is shorted at GND. Transmission circuit of outdoor PCB is abnormal. Transmission circuit of indoor PCB is abnormal. Check Point 1. Check the input power AC 208~230V. (Outdoor, Indoor unit) 2. Check the communication wires are correctly connected. Adjust the connection of wire Confirm the wire of Live, Neutral 3. Check the resistance between communication line and GND. (rmal : Over 2MΩ) 4. Check the connector for communication is correctly connected. 5. Check the connection of GND1, GND2, and main GND. 6. If one indoor unit is operated normally, outdoor PCB is no problem. Check the another indoor unit. * CH05 is displayed at indoor unit, CH53 is displayed at outdoor unit

58 Part 4 Trouble Shooting 3) Troubleshooting CH21 Error code 21 DC Peak Title Cause of error Check point & rmal condition Instant over current Over Rated current Poor insulation of IPM An instant over current in the U,V,W phase - Comp lock - The abnormal connection of U,V,W Over load condition - Overcharging of refrigerant - Pipe length. Poor insulation of compressor Comp U Resistance(Ω) at 20 C(68 F) V W Ω Terminal U-V V-W W-U Inverter comp Constant comp Comp Copper pipe Ω Resistance(Ω) at 20 C(68 F) Terminal U-GND V-GND W-GND Inverter comp. 2MΩ 2MΩ 2MΩ Constant comp. 2MΩ 2MΩ 2MΩ Check Point 1. Check the wire connection. (U,V,W) 2. Check the load condition. (Refrigerant, Pipe length, ) Adjust the load condition 3. Check the electricity leakage of the compressor. rmal : Over 2MΩ. 4. Check the resistance of compressor. rmal : 0.65Ω(INV), 0.8Ω(Cons.) difference at each terminal. 5. Check the insulation from water at IPM part. Check the trace of water. 6. Check the IPM circuit

59 Part 4 Trouble Shooting 4) Troubleshooting CH21, CH22 Error code Title Cause of error Check point & rmal condition DC_Peak C/T Internal circuit Compressor output current over.(30a ) Initial current error Check the compressor locking. Check the compressor insulation and motor wire resistance. Check outdoor fan locking,operating. Check the IPM short. Check AC input voltage. Check outdoor fan locking,operating. Check input current. Check the C01N DC voltage. (From the condition where the electricity is entering and Before the product operates, rmality Vdc value is 2.5V±0.2V) V Check Point 1. Check the power source. 2. Check the fan operation is right. 3. Check the current. 4. Check the install condition. 5. Check the internal circuit

60 Part 4 Trouble Shooting 5) Troubleshooting CH23, CH28 Error code Title Cause of error Check point & rmal condition 23 DC Link Low voltage. DC link volt. is 140VDC. Check the power source. Check the DC Link Voltage. 28 DC Link High voltage DC link volt. is 420VDC. Check the power source. Check the DC Link Voltage. Check Point 1. Check the power source. 2. Check the DC Link Voltage. V

61 Part 4 Trouble Shooting 6) Troubleshooting CH24, CH25 Error code Title Cause of error Check point & rmal condition 24 Press S/W Open Low / High press S/W open. Check the connection of CN_Press. Check the components. 25 Input voltage Abnormal Input voltage (140VAC, 300VAC ). Check the power source. Check the components. TRANS1 60Hz, DC12V CN PRESS CN TRNAS1 Check Point CH Check the connection of CN_PRESS 2. Check the install condition for over load. 3. Check the SVC V/V open. 4. Check the leakage of refrigerant. CH Check the power source. 2. Check the components (Trans1, B/Diode, Diode, Resistance)

62 Part 4 Trouble Shooting 7) Troubleshooting CH26, CH27 Error code Title Cause of error Check point & rmal condition 26 DC Compressor Position Compressor position detect error Check the connection of comp wire U,V,W Malfunction of compressor Check the component of IPM, detection parts. 27 PSC Fault Over current at IGBT Check the Reactor spec. (18k,30k:10A/26.8mH, 24k:13A/13mH * 2) Check AC input voltage. Check outdoor fan locking,operating. Check input current. A B Check Point CH 26 Check the connection of "U, V, W" Check the short check point "A" Check with the error code "21" CH 27 Check the "IGBT" short point "B"

63 Part 4 Trouble Shooting 8) Troubleshooting CH32, CH33, CH40 Error code 32 Title Cause of error Check point & rmal condition D-pipe (Inverter) temp. high (105 C(221 F) ) Discharge sensor (Inverter) temp. high Check the discharge pipe sensor for INV. Check the install condition for over load. Check the leakage of refrigerant. Check the SVC V/V open. 33 D-pipe (Constant) temp. high (105 C(221 F) ) Discharge sensor (Cons.) temp. high Check the discharge pipe sensor for Cons. Check the install condition for over load. Check the leakage of refrigerant. Check the SVC V/V open. 40 CT Sensor Open/Short Soldered poorly Internal circuit error rmal resistor : about 0Ω D-Pipe temp. Toff(105) C (221) F T2(95) C (203) C T1(90) C (194) C COMP Frequency (Hz) rmal rmal OFF LEV Openness (Pulse) rmal rmal OFF Control Check Point CH Check the install condition for over load. 2. Check the SVC V/V open. 3. Check the leakage of refrigerant. CH If the resistance of the sensor is only, the check Is possible. 2 If the error occurs again after the reset, change the PCB. CH Check the install condition for over load. 2. Check the SVC V/V open. 3. Check the leakage of refrigerant. 4. Check the constant compressor. (same with CH21)

64 Part 4 Trouble Shooting 9) Troubleshooting CH41, CH44, CH45, CH46, CH47, CH65 Display code Title Cause of error Check point & rmal condition 41 D-pipe sensor (Inverter) Open / Short Soldered poorly Internal circuit error rmal resistor : 200kΩ / at 25 C(77 F) (Unplugged) rmal voltage : 4.5VDC / at 25 C(77 F) (plugged) 44 Air sensor Open / Short Soldered poorly Internal circuit error rmal resistor : 10kΩ / at 25 C(77 F) (Unplugged) rmal voltage : 2.5VDC / at 25 C(77 F) (plugged) 45 Condenser Pipe sensor Open / Short Soldered poorly Internal circuit error rmal resistor : 5kΩ / at 25 C(77 F) (Unplugged) rmal voltage : 2.5VDC / at 25 C(77 F) (plugged) 46 Suction Pipe sensor Open / Short Soldered poorly Internal circuit error rmal resistor : 5kΩ / at 25 C(77 F) (Unplugged) rmal voltage : 2.5VDC / at 25 C(77 F) (plugged) 47 D-pipe sensor (Constant) Open / Short Soldered poorly Internal circuit error rmal resistor : 200kΩ / at 25 C(77 F) (Unplugged) rmal voltage : 4.5VDC / at 25 C(77 F) (plugged) 65 Heat sink sensor Open / Short Soldered poorly Internal circuit error rmal resistor : 10kΩ / at 25 C(77 F) (Unplugged) rmal voltage : 2.5VDC / at 25 C(77 F) (plugged) Ω Check Point 1. Estimate the resistance of each sensor.(unplugged) 2. Estimate the voltage of each sensor.(plugged) 3. If the resistance of the sensor is 0 kω or, then sensor is abnormal. If the voltage of the sensor is 0 V or 5VDC, then sensor is abnormal

65 Part 4 Trouble Shooting Inverter/Constant D-Pipe R-T Table Temperature( C/ F) Resistance(kΩ) 20/ / / / / / / / / / / Air R-T Table Temperature( C/ F) Resistance(kΩ) 20/ / / / / / / / / Condenser/Suction Pipe Pipe R-T Table Temperature( C/ F) Resistance(kΩ) 20/ / / / / / / / / Heatsink R-T Table Temperature( C/ F) Resistance(kΩ) 20/ / / / / / / / / / / ) Troubleshooting CH51, CH60 Display code Title Cause of error Check point & rmal condition 60 EEPROM Check sum Check sum error Check the PCB ASM P/. Check the poor soldering. Check Point CH Check the insertion condition of EEPROM. 2. Check the poor soldering

66 Part 4 Trouble Shooting 11) Troubleshooting CH61, CH62 Display code Title Cause of error Check point & rmal condition 61 Condenser pipe sensor temp. high Condenser pipe sensor detected high temp.(65 C(149 F)) Check the load condition. Check the sensor of Condenser pipe sensor. 62 Heat sink sensor temp. high Heat sink sensor detected high temp.(85 C(185 F)) Check the fan is locked. Check the sensor of heat sink. Heat Sink temp. Toff C T2 C T1 C COMP Frequency (Hz) rmal rmal OFF rmal Check Point CH Check the install condition for over load. (Refrigerant, Pipe length, Blocked, ) CH Check the fan is locked. 2. Check the Outdoor temp. is very high

67 P/NO : MFL JAN