BroadSoft Partner Configuration Guide

Transcription

1 BroadSoft Partner Configuration Guide Ascom IP DECT Series December 2013 Document Version 1.2 Grimbodalen Göteborg, Sweden Phone:

2 BroadWorks Guide Copyright tice Trademarks Ascom All rights reserved. The entire content of this Ascom document is copyright protected with all rights reserved. All property rights shall remain with Ascom. The terms and conditions for the use of the Ascom document shall be deemed to be accepted, if a user downloads or otherwise copies any content from the Ascom document. BroadWorks and BroadWorks Assistant Enterprise, BroadWorks Call Center, BroadWorks Communicator, BroadWorks Receptionist, and BroadWorks Deployment Studio are trademarks of BroadSoft, Inc. Microsoft, MSN, Windows, and the Windows logo are registered trademarks of Microsoft Corporation. Other product names mentioned in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. This document is printed in the United States of America ASCOM PAGE 2 OF 26

3 Document Revision History Version Reason for Change 1.1 Introduced document for Ascom IP DECT Series version validation with BroadWorks Release 19.sp Edited and published document ASCOM PAGE 3 OF 26

4 Table of Contents 1 Overview Interoperability Status Verified Versions Interface Capabilities Supported Interface Capabilities Supported Known Issues BroadWorks Configuration BroadWorks Device Profile Type Configuration BroadWorks Configuration Steps IP DECT Series Configuration Subscriber Level Configuration Parameters Advanced SIP Features Configuration Xtended Services Interface Feature Configuration Instant Message and Presence Configuration Device Management Appendix A: Sample IP DECT Configuration Files References ASCOM PAGE 4 OF 26

5 1 Overview This guide describes the configuration procedures required for the Ascom IP DECT Series for interoperability with BroadWorks. This includes the following models: Ascom IP-DECT Base Station, IPBS2, v Ascom IP-DECT Base Station, IPBS1, v Ascom IP-DECT Gateway, IPBL, v The IP DECT is a series of cordless IP DECT base stations that use the Session Initiation Protocol (SIP) to communicate with BroadWorks for call control. This guide describes the specific configuration items that are important for use with BroadWorks. It does not describe the purpose and use of all configuration items on the IP DECT series. For those details, see the Installation and Operation Manual, IP-DECT Base Station and IP-DECT Gateway, TD 92579EN [1] supplied by Ascom ASCOM PAGE 5 OF 26

6 2 Interoperability Status This section provides the known interoperability status of the Ascom IP DECT Series with BroadWorks. This includes the version(s) tested, capabilities supported, and known issues. Interoperability testing validates that the device interfaces properly with BroadWorks via the SIP interface. Qualitative aspects of the device or device capabilities not affecting the SIP interface such as display features, performance, and audio qualities are not covered by interoperability testing. Requests for information and/or issues regarding these aspects should be directed to Ascom. 2.1 Verified Versions The following table identifies the verified Ascom IP DECT Series and BroadWorks versions and the month/year the testing occurred. If the device has undergone more than one test cycle, versions for each test cycle are listed, with the most recent listed first. Compatible Versions in the following table identify specific IP DECT versions, which the partner has identified as compatible and should interface properly with BroadWorks. Generally, maintenance releases of the validated version are considered compatible and are not specifically listed here. For any questions concerning maintenance and compatible releases, contact Ascom. NOTE: Interoperability testing is usually performed with the latest generally available (GA) device firmware/software and the latest GA BroadWorks release and service pack at the time the testing occurs. If there is a need to use a non-verified mix of BroadWorks and device software versions, customers can mitigate their risk by self-testing the combination using the BroadWorks SIP Access Device Interoperability Test Plan [4]. Verified Versions Date (mm/yyyy) BroadWorks Release IP DECT Verified Version IP DECT Compatible Versions 11/2013 Release 19.sp List any specific compatible versions. 2.2 Interface Capabilities Supported This section identifies interface capabilities that have been verified through testing as supported by Ascom IP DECT Series. The Supported column in the tables in this section identifies the Ascom IP DECT Series support for each of the items covered in the test plan, with the following designations: Test item is supported. Test item is not supported. NA Test item is not applicable to the device type. NT Test item was not tested. Caveats and clarifications are identified in the Comments column ASCOM PAGE 6 OF 26

7 2.2.1 Interface Capabilities Supported The Ascom IP DECT Series has completed interoperability testing with BroadWorks using the BroadWorks SIP Access Device Interoperability Test Plan [4]. The results are summarized in the following table. The BroadWorks test plan is composed of packages, each covering distinct interoperability areas, such as Basic call scenarios and Redundancy scenarios. Each package is composed of one or more test items, which in turn, are composed of one or more test cases. The test plan exercises the SIP interface between the device and BroadWorks with the intent to ensure interoperability sufficient to support the BroadWorks feature set. NOTE: DUT in the following table refers to the Device Under Test, which in this case is the Ascom IP DECT Series. BroadWorks SIP Access Device Interoperability Test Plan Support Table Test Plan Package Test Plan Package Items Supported Comments Basic Call Origination Call Termination Session Audit Session Timer Ringback Forked Dialog Early UPDATE Early-Session 181 Call Being Forwarded Dial Plan Dual-Tone Multi-Frequency (DTMF) Inband DTMF RFC 2833 DTMF DTMF Relay Codec Negotiation Codec Renegotiation BroadWorks Services Third-Party Call Control Basic There is partial implementation of advanced call control. Third-Party Call Control Advanced Voice Message Deposit or Retrieval Message Waiting Indicator message count support Voice Portal Outcall Advanced Alerting Calling Line ID 2013 ASCOM PAGE 7 OF 26

8 BroadWorks SIP Access Device Interoperability Test Plan Support Table Test Plan Package Test Plan Package Items Supported Comments DUT Services Call Control Services DUT Services Registration and Authentication Calling Line ID with Unicode Characters Connected Line ID Connected Line ID with Unicode Characters Connected Line ID on UPDATE Connected Line ID on Re-INVITE Diversion Header History-Info Header Advice of Charge Meet-Me Conferencing Call Waiting Call Hold Call Transfer Three-Way Calling Network-Based Conference Register Authentication Maximum Registration Minimum Registration Invite Authentication Re-Invite or Update Authentication Refer Authentication Device Authenticating BroadWorks DUT Services Fax G711 Fax Passthrough NA DUT Services Emergency Call DUT Services Miscellaneous G711 Fax Fallback T38 Fax Messaging Emergency Call Emergency Call with Ringback Do t Disturb Call Forwarding Always Call Forwarding Always Diversion Inhibitor Anonymous Call Anonymous Call Block Remote Restart Via tify NA NA Advanced Phone Busy Lamp Field 2013 ASCOM PAGE 8 OF 26

9 BroadWorks SIP Access Device Interoperability Test Plan Support Table Test Plan Package Test Plan Package Items Supported Comments Services Busy Lamp Field Call Park tification Advanced Phone Services Feature Key Synchronization, Private Line Advanced Phone Services Feature Key Synchronization, Shared Line Advanced Phone Services Missed Calls Display Synchronization Advanced Phone Services Shared Call Appearance using Call Info Advanced Phone Services Call Center Advanced Phone Services Call Park tification Do t Disturb Do t Disturb Ring Splash Call Forwarding Call Forwarding Always Ring Splash Call Forwarding Always Diversion Inhibitor Call Center Agent Logon or Logoff Call Center Agent Unavailable Code Do t Disturb Do t Disturb Ring Splash Call Forwarding Call Forwarding Always Ring Splash Call Forwarding Always Diversion Inhibitor Missed Calls Display Sync Line-Seize Call-Info or Lamp Management Public Hold Private Hold Hybrid Key System Multiple Call Arrangement Bridging Call Park tification Hold Reminder Call Information Hoteling Event Status Event Disposition Code Emergency Escalation Customer Originated Trace Call Park tification Redundancy Domain Name System (DNS) 2013 ASCOM PAGE 9 OF 26

10 BroadWorks SIP Access Device Interoperability Test Plan Support Table Test Plan Package Test Plan Package Items Supported Comments SRV Lookup Session Border Controller (SBC)/Application Layer Gateway (ALG) Video Basic Video Calls Video BroadWorks Video Services Register Failover or Failback Invite Failover or Failback Bye Failover Register Outgoing Invite Incoming Invite Call Origination Call Termination Call Hold Call Waiting Call Transfer Auto Attendant Auto Attendant HD Voice Messaging Voice Messaging HD Custom Ringback NA NA NA NA NA NA NA NA NA NA TCP Register Outgoing Invite Incoming Invite IPV6 Call Origination Call Termination Session Audit Ringback Codec Negotiation or Renegotiation Voice Message Deposit or Retrieval Call Control Registration with Authentication T38 Fax Messaging Busy Lamp Field Redundancy SBC Video Dual Stack with Alternate Connectivity 2013 ASCOM PAGE 10 OF 26

11 2.2.2 Other Interface Capabilities The Ascom IP DECT Series does not offer BroadWorks Xtended Services Interface or BroadCloud IM&P support. 2.3 Known Issues This section lists the known interoperability issues between BroadWorks and specific partner release(s). Issues identified during interoperability testing and known issues identified in the field are listed. The following table provides a description of each issue and, where possible, identifies a workaround. The verified partner device versions are listed with an X indicating that the issue occurs in the specific release. The issues identified are device deficiencies or bugs, and are typically not BroadWorks release dependent. If the testing was performed by BroadSoft, then the Issue Number is a BroadSoft ExtraView partner issue number. If the testing was performed by the partner or a third party, then the partner may or may not supply a tracking number. For more information on any issues related to the particular partner device release, see the partner release notes. Issue Number Issue Description Partner Version EV Ascom IP DECT does not support Allow-Events Hold There is a partial implementation of advanced call control where the Hold event is un-available. This causes the 3 rd party advanced call control functionalities to be broken. Further, the call hold scenario can only be invoked at the end point. Workaround: Call hold needs to be invoked on the device and cannot be perform through 3 rd party call control. X 2013 ASCOM PAGE 11 OF 26

12 3 BroadWorks Configuration This section identifies the required BroadWorks device profile type for the Ascom IP DECT Series as well as any other unique BroadWorks configuration required for interoperability with the IP DECT. 3.1 BroadWorks Device Profile Type Configuration This section identifies the device profile type to use when deploying the Ascom IP DECT Series with BroadWorks. The following table identifies the required BroadWorks device identity/profile type settings for interoperability between the IP DECT and BroadWorks. For an explanation of the profile parameters, see the BroadWorks Device Management Configuration Guide [2]. For most of the following parameters, an X indicates that the parameter function is supported and/or required. If the item is blank, it is not supported. For items where text is supplied, the text content maps directly to the web page to add or to modify a device profile type. Ascom IP DECT Series Identity/Device Profile Type Signaling Address Type Intelligent Proxy Addressing Number of Ports 1 Standard Options Ringback Tone or Early Media Support Authentication Local Ringback Early Media Enabled Hold rmalization RFC 3264 Registration Capable X Static Registration Capable E.164 Capable Trusted Authenticate REFER X Video Capable Use History-Info Header Advanced Options Route Advance Wireless Integration PBX Integration Add P-Called-Party-ID Auto Configuration Soft Client Requires BroadWorks Call Waiting Tone Advice of Charge Capable 2013 ASCOM PAGE 12 OF 26

13 Ascom IP DECT Series Identity/Device Profile Type Support Emergency Disconnect Control Enable Monitoring Static Line/Port Ordering Forwarding Override Conference Device Music On Hold Device Requires BroadWorks Digit Collection Requires MWI Subscription Support Call Center MIME Type Support Identity in UPDATE and Re-INVITE Support RFC 3398 Reset Event Trunk Mode Hold Announcement Method Unscreened Presentation Identity Policy t Supported User Inactive Profile Web Based Configuration URL Extension Device Configuration Options Device Configuration Options t Supported 3.2 BroadWorks Configuration Steps There are no additional BroadWorks configurations necessary ASCOM PAGE 13 OF 26

14 4 IP DECT Series Configuration The Ascom IP-DECT can be configured through its embedded web server. The following examples describe how to set the parameters using a configuration file. This configuration description assumes the Ascom IP-DECT uses the Dynamic Host Configuration Protocol (DHCP) to obtain an IP address, and other network settings. The Ascom IP-DECT should be configured to load the configuration file each time it resets or re-synchronizes. For detailed information on automated provisioning, see the Installation and Operation Manual, IP-DECT Base Station and IP-DECT Gateway, TD 92579EN [1]. The capabilities of the Ascom IP-DECT have been verified for use with BroadWorks based on the settings described in the following table. For more information on the meaning, purposes, and applicability of the individual configuration Items, see the Installation and Operation Manual, IP-DECT Base Station and IP-DECT Gateway TD, 92579EN [1]. Configuration Files Files Provided by Partner Level Description IPBS2_firm_v6p1p2.bin Static Contains the device firmware load. intop_bs_complete-ipbs Subscriber Contains configurable parameters that apply to an individual device in a deployment. 4.1 Subscriber Level Configuration Parameters This section identifies the device-specific parameters, including registration and authentication. These settings must be unique across devices to be matched with the settings for a BroadWorks subscriber. Provisioning a subscriber to register with BroadWorks allows calls to terminate to the subscriber s line. Registration requires that a unique address of record (AoR) is provisioned on BroadWorks and the phone. Provisioning an AoR on BroadWorks consists of setting the line/port parameter to a unique value within the Application Server cluster. Step Command Purpose System Configuration File: intop_bs_complete-ipbs Step 1 Step 2 Step 3 Set the SIP Proxy/Domain. sipproxy = as.broadworks.net Set the Outbound Proxy. outboundproxy = sbc.broadworks.net Enable DNS SRV lookup. Use_DNS_SRV = ; Set the IP-DECT SIP server to the Fully Qualified Domain Name (FQDN) for the BroadWorks Application Server cluster. The domain must match the domain configured for the BroadWorks subscriber s line/port domain. Set the outbound proxy to the SBC if one is deployed between the IP- DECT and BroadWorks. If there are redundant SBCs, set it to the FQDN for the SBC cluster. Enable DNS SRV lookups ASCOM PAGE 14 OF 26

15 Step Command Purpose System Configuration File: intop_bs_complete-ipbs Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 Step 10 Step 11 Step 12 Set register mode. RegistMode = 1 Set SIP Timers. SIP_T1 ".5" ; SIP_T2 "4" ; SIP_T4 "4" ; INVITE_Expires "240" ; ReINVITE_Expires "30" ; Reg_Min_Expires "1" ; Reg_Max_Expires "86400" ; Reg_Retry_Intvl "30" ; Reg_Retry_Long_Intvl "600" ; Enable reliable response. SIP_100REL_Enable "" ; Enable audio message waiting indicator (MWI). MwitifyTone = 1 Enable negotiated DTMF type. Auto_DTMF_Mode = 1 Set hold implementation type. HoldType = 3264 Set ring types. DttvRingInt1 = dr2 DttvRingInt2 = dr3 DttvRingInt3 = dr4 DttvRingExt2 = dr5 Set call waiting tone types. DttvCallWaitRing1 = CallWaitingTone1 DttvCallWaitRing2 = CallWaitingTone Configure the dial plan. Example: Dial_Plan " ( [ ]11S0 [0-1][2-9]11S0 0 00S0 01[2-9]xx. *xx 011x. [0-1]xxxxxxx [0-1][2-9]xxxxxxxxxS0 [2-9]xxxxxxxxxS0 [2-9]xxxxxx 101xxxx. 11S0 [2-9]x. ) " ; Enable SIP register. Set the SIP timers to levels short enough to support a timely failover when there is no server response. The suggested registration period (Reg Max Expires) is one day or seconds. Set the Reg Retry Long Intvl timer to 600 (10 minutes) to limit the frequency of REGISTER retries after a 403 Forbidden response. Reliable provisional response (PRACK) should be enabled. Optional: Enable the phone to play an audio alert for an incoming voice message. Set the IP-DECT to enable inband or RFC 2833 negotiated DTMF. Recommended: Set the hold implementation to RFC Identify distinctive ring types for BroadWorks priority alerting (dr2), alternate numbers (dr3 and dr4), and ring splash (dr5) features. This enables the phone to play a distinctive ring when these features are invoked. Configure the phone to enable distinctive call waiting tones. Configure the IP-DECT dial plan according to the locale. The dial plan shown is an example of a typical rth American dial plan ASCOM PAGE 15 OF 26

16 Step Command Purpose System Configuration File: intop_bs_complete-ipbs Step 13 Step 14 Step 15 Step 16 Step 17 Enable supplementary services. Conference "" ; Attn_Transfer "" ; Blind_Transfer "" ; Enable each line to be used. Line_Enable[1] "" ; Line_Enable[2] "" ; Set Register User ID for each line. Example: User_ID[1] " " ; User_ID[2] " " ; Enable SIP Authentication for each line. Example: Auth_ID[1] "1111@as.mycompany.com" ; Password[1] "welcome" ; Auth_ID[2] "2222@as.mycompany.com" ; Password[2] "welcome" ; Configure display name for each line. Example: Display_Name[1] Claire Smith ; Display_Name[2] Julie Wenkel ; Enable Conference, Attended Transfer, and Blind Transfer services controlled from the phone. Enable each IP-DECT in use. The register user ID must correspond with the line/port setting on BroadWorks. If the Authentication service is configured on BroadWorks, these parameters must be configured to match the BroadWorks settings. For each line, configure the name to be displayed on the device. 4.2 Advanced SIP Features Configuration The Ascom IP-DECT does not support advanced SIP features. 4.3 Xtended Services Interface Feature Configuration The Ascom IP-DECT does not support Xtended Services Interface features. 4.4 Instant Message and Presence Configuration The Ascom IP-DECT does not support IM&P features ASCOM PAGE 16 OF 26

17 5 Device Management The Ascom IP DECT Series does not currently support the BroadWorks Device Management feature ASCOM PAGE 17 OF 26

18 Appendix A: Sample IP DECT Configuration Files NOTE: The following samples are examples and should be used as a reference only. DO NOT CUT AND PASTE THESE EXAMPLES TO GENERATE YOUR CONFIGURATION FILES. Use the configuration files obtained from Ascom with the specific release to generate your configuration files. Phone-Specific File: intop_bs_complete-ipbs txt NOTE: This is an example file and should be used for reference only. vars check 40c7f6a5417cf827ae80d311e004 # IPBS2[6.1.2], Bootcode[6.1.2], Hardware[IPBS2-A3/1B1] # IPBS # config change FLASHMAN0 config change VARS config change SNMP0 config change ASC_SUBAGNT0 config change LOG0 config change LOG0 FAULT config change LOG0 CNT config change CDR0 config change CDR1 config change CPU config change ASC_LOGGING0 config change SER0 config change SPI0 config change SER1 config change MSP0 config change ETH0 config change PPPOE0 config change PPTP config change IP0 config change IP0 ETH0 /addr /mask /dns config change IP0 PPP0 config change IP0 PPP1 config change IP0 PPP2 config change IP0 PPP3 config change IP0 RT0 /gateway config change IP0 RT1 config change IP0 RT2 config change IP0 RT3 config change IP6 config change IP6 ETH0 config change IP6 6TO4-00 config change IP6 6TO4-01 config change IP6 6TO4-02 config change IP6 6TO4-03 config change IP6 6TO4-04 config change IP6 6TO4-05 config change IP6 6TO4-06 config change IP6 6TO4-07 config change ENET1X ASCOM PAGE 18 OF 26

19 config change NAT0 config change NAT0 H323NAT0 config change DNS0 config change KEYGEN config change X509 config change TLS_CIPHER0 config change TLS0 config change CMD0 /name DECT2 config change PCAP config change HTTPCLIENT0 config change WEBDAV0 config change HTTP0 /force-https config change TELNET0 config change PING0 config change WEBMEDIA config change MEDIA-FWD config change MEDIA config change NTP0 /addr /alt-addr /interval 60 /offset CET-1CEST-2,M3.5.0/2,M10.5.0/3 config change SYNC config change DHCP0 /mode off config change FLASHDIR0 config change LDAPSRV0 config change LDAPDIR0 config change LDAPREP0 /server /user ipdect /repl-type FULL- REPL /dn cn%3dpbx0 /filter-gui DECT config change KERBEROS config change KDB0 config change TESTIF0 config change RFP0 /module-trace config change RFP0 RFPDWL config change RFPSTAT0 config change RFPINIT0 /mode master /sync-region 0 /resync 0 /hour1 0 /day 0 /hour2 0 /module-trace config change RFPINIT0 PRODPARAM /module-trace config change DECT /cipher /dbgmask 0x0 /module-trace config change DECT /cipher /dbgmask 0x0 /module-trace config change H323 config change SIP /log on /msg-trace on config change TSIP config change SIPS config change TEST config change TONE config change HTTP config change ECHO config change SIG0 config change SIG1 config change SMTP0 config change UP0 config change UP1 config change ASDP config change UNITED config change CUNITE /module-trace config change CUNITE FILEGET /module-trace config change CUNITE CALLINFO config change CUNITE KEYVALUE config change DEVICELIC config change UNITE /module-trace config change UNITE UTP /module-trace config change UNITE GROUPHANDLER config change UNITE FAULTHANDLER config change UNITE DEVMANHANDLER /module-trace config change MATP /module-trace 2013 ASCOM PAGE 19 OF 26

20 config change CUTP /port /module-trace config change SMSRL /encryption config change SMSC config change AIRSYNCCTRL /module-trace config change PHONEBOOK config change PHONEBOOK PHBFLASH0 config change ICP /module-trace config change GW-DECT /kp /disc-no-ct /coder G711A,20, /name DECT config change GW-DECT LOCALUSERS /kp config change GW-DECT CRYPTOMASTER config change GW-DECT MOBMASTER config change GW-DECT MASTER /users-per-sec 500 /mode ACTIVE /id 0 /prot SIP /proxy /gk /gk-id as.iop1.broadworks.net /int-num-len 4 /sip-hold inactive /status-inq-period 90 /supervision 600 /enbloc /pari-active /allow-rtp-dtmf /auth-name /trace-mask config change GW-DECT DYNCFG /cmd form /xsl dyncfg.xsl /save OK /userid admin config change GW-DECT DISPLAY config change GW-DECT RADIO /master-name DECT /master /alt-master /trace-mask config change GW-DECT SMSCLGA config change GW-DECT MIHOTDESK /module-trace config change GW-DECT DATAFWD /module-trace config change GW-DECT DECTPARI /sarilistlen 10 /sysid 120 config change GW-DECT FTY /pick. /pin. /lock. /lock0. /dnd-int. /dnd-int0. /dnd-ext. /dnd-ext0. /park. /park0. /pick-grp. /pick-dir. /park-to. /park-to0. /mwi-mode USER-INTERROGATE-USER-NOTIFY /mwi /grp. /grp0. /nclir. /nclir0. /clir. /clir0. config change RELAY0 config change RELAY0 FTY config change RELAY0 RELAY-SIP config change RELAY0 RELAY-TSIP config change RELAY0 RELAY-SIPS config change RELAY0 TEST config change RELAY0 TONE config change RELAY0 HTTP config change RELAY0 ECHO config change RELAY0 SIG0 config change RELAY0 SIG1 config change RELAY0 SIP1 config change RELAY0 SIP2 config change RELAY0 SIP3 config change RELAY0 SIP4 config change RELAY0 GW1 config change RELAY0 GW2 config change RELAY0 GW3 config change RELAY0 GW4 config change RELAY0 GW5 config change RELAY0 GW6 config change RELAY0 GW7 config change RELAY0 GW8 config change RELAY0 GW9 config change RELAY0 GW10 config change RELAY0 GW11 config change RELAY0 GW12 config change RELAY0 RT1 config change RELAY0 RT2 config change RELAY0 RT3 config change RELAY0 RT4 config change RELAY0 RT5 config change RELAY0 RT6 config change RELAY0 RT7 config change RELAY0 RT ASCOM PAGE 20 OF 26

21 config change RELAY0 RT9 config change RELAY0 RT10 config change RELAY0 RT11 config change RELAY0 RT12 config change RELAY0 RT13 config change RELAY0 RT14 config change RELAY0 RT15 config change RELAY0 RT16 config change RELAY0 RT17 config change RELAY0 RT18 config change RELAY0 RT19 config change RELAY0 RT20 config change RELAY0 RT21 config change RELAY0 RT22 config change RELAY0 RT23 config change RELAY0 RT24 config change RELAY0 RT25 config change RELAY0 RT26 config change RELAY0 RT27 config change RELAY0 RT28 config change RELAY0 RT29 config change RELAY0 RT30 config change RELAY0 RT31 config change RELAY0 RT32 config change RELAY0 REG config change-flags vars del vars create AIRSYNC/REGION/000 p vars create CMD0/AUTH pc 40c7f6a5417cf827ae80d311e004 vars create CPU/BOX-INIT p vars create DECT/SYSID pb vars create DHCP0/LAST-LEASE p , , , , ,, vars create GW-DECT/RADIOS/IPBS c8 p 901EB51008,Ascom+IP- DECT+Base+Station:DECT2 vars create GW-DECT/RADIOS/IPBS p 901EB52009,Ascom+IP- DECT+Base+Station:DECT2 vars create LDAPREP0/AUTH pc 48d3ffa94c24 vars create LDAPSRV0/AUTH pc 4dc7fabc0237ee2abc9a8e1dfd196e0d459d vars create PBX0/KEY pbc b82f6a4b7ccfd0b0868d202fc4 vars create PBX0/PWD pc 42cbfaa24835f62acfeeb4748d vars create PPP0/LOCAL-AUTH pc vars create PPP0/REMOTE-AUTH pc vars create PPP1/LOCAL-AUTH pc vars create PPP1/REMOTE-AUTH pc vars create PPP2/LOCAL-AUTH pc vars create PPP2/REMOTE-AUTH pc vars create PPP3/LOCAL-AUTH pc vars create PPP3/REMOTE-AUTH pc vars create RADIO/MASTERPWD pc 42cbfaa24835f62acfa2f035dd vars create UPDATE/VIRGIN p 1 vars create X509/DEVICE_CERTIFICATE/00000 pb d a cfe5b449300d06092a864886f70d c3 11a c d30312d33652d31332d31352d e170d a170d a301c311a c d30312d33652d31332d31352d f300d06092a864886f70d d a7ddc95a7d0ec8ab231bbe6fcae5a06e4d1a5475a38a33746a2c94e c6f4f77d521e986f371c acc7b0eece98c95cdaddbca08b2ef1b1f93b99b113f749 f24f1819c1ebf7e08948fa78d5bcee6cf7bcff7a df748e046f7affe43eab24 c0bac20d0a fd5773c5fdf7bd69d b c a36c306a d130101ff ff e d0f0101ff a d eca4a7a60d088fbfa d62f38bdeed d0e eca4a7a60d088fbfa d62f38bdeed068300d ASCOM PAGE 21 OF 26

22 92a864886f70d a66fb2c1de03ea4bf151fcad9997d7ba3544f78b93 c89a1497a649a368e275db9be5fc a33bb5f6ec7eb9d1ab f c60f4652c35791e83af68f23961a587b710c7669a74eb66cd783030a93456db89391d 875dfea e1ec4c0b4ddcab1719c8b3d4a69038f0fad8e0f5a72f603f18c7f2 vars create X509/DEVICE_KEY pbc d519b4d4e6fb4d350a84c087127cc1f794e56cac177e2ce1c5cfd81f8313f0ab 71a7af8a9c941ef42a8a8df8f6de1f5bf448469ef7c458f5588cd51f4a0a04403d42f96ed 34ed387ff06b9b323eb382220fa5914da9788aaede cd2949cb a758ea d1e95cce2860eb8da15b271cda7fa4a0c240339e33ccabd2cda87d4ad13478a5a907adbc d962ce5ceb65a83bce2faaafc156ded037319f5f0fd08ae2b5f2f265abeee4d 44e532230d05e32bac fa72b21a10cae2e2661d976b27e0f8a3a50a e fc058d71edd5390b86e16b43a1b9bbde4ed71c87e1e3f7c52ae2ed4ad99517e379b559 bbf3eb0b91531ece80c940b50a274540dd9454c8737d67a b0eee49c6aaf2574c57 69f128f41e6bb92de711dfce961d41976f5e81e7ea12421c43d427f0002e7dc182dd30f9a 437ec51545bfbff45be223390eb2e444e bc056c4ef37970cf6fba622d8a4b07c0 4abf0d3a ae0d9bd74344d873e ed3f85145fa182d235e9ddc58d0de 1a7515de ae44edc7f58fce2a154939c0748ed1d0eda6b1476b6b86e9f7b22ec2 b6ef3893bb23c592a7e730aab54fff86f151ee4c82f2ba158966ea d93e95b4f41 98a7d78c5d261e4855eea cf679f219f5d429881a0342dc7c737fc301f95b12c601 86de79558f15bc7dc219f6a4dcc137f7ee abca4af7e39f05e1bb23522da7ed01fe 4b570b02f99a d41c07cd f89a063661efdf4f428f c5a4a2df6e fd6cfa49c17d9dee10704d1af7200dda9b7998d b5d vars create X509/INIT p 1 mod cmd FLASHDIR0 erase-all mod cmd FLASHDIR0 add-view 101 cn=kdb0 mod cmd FLASHDIR0 add-view 102 cn=pbx0 mod cmd FLASHDIR0 add-item 102 (cn=test 00)(h323=2000)(e164=2000)(loc=.)(node=root)(pbx=<user filter="normal" cdfilter="normal" cfnr="15" busy-in="65535" busyout="2"/>)(guid;bin=0c385b30e909d31197b ad)(usn=46) mod cmd FLASHDIR0 add-item 102 (cn=test 03)(h323=2003)(e164=2003)(loc=.)(node=root)(pbx=<user filter="normal" cdfilter="normal" cfnr="15" busy-in="65535" busyout="2"/>)(guid;bin=018a5373e909d311a ad)(usn=47) mod cmd FLASHDIR0 add-item 102 (cn=test 04)(h323=2004)(e164=2004)(loc=.)(node=root)(pbx=<user filter="normal" cdfilter="normal" cfnr="15" busy-in="65535" busyout="2"/>)(guid;bin=018e1ac9e909d311a ad)(usn=48) mod cmd FLASHDIR0 add-item 102 (cn=test 05)(h323=2005)(e164=2005)(loc=.)(node=root)(pbx=<user filter="normal" cdfilter="normal" cfnr="15" busy-in="65535" busyout="2"/>)(guid;bin=02fdb4ebe909d311b ad)(usn=49) mod cmd FLASHDIR0 add-item 102 (cn=test 06)(h323=2006)(e164=2006)(loc=.)(node=root)(pbx=<user filter="normal" cdfilter="normal" cfnr="15" busy-in="65535" busyout="2"/>)(guid;bin= e909d311b ad)(usn=50) mod cmd FLASHDIR0 add-item 102 (cn=test 07)(h323=2007)(e164=2007)(loc=.)(node=root)(pbx=<user filter="normal" cdfilter="normal" cfnr="15" busy-in="65535" busyout="2"/>)(guid;bin=05a2e2cee909d311b ad)(usn=51) mod cmd FLASHDIR0 add-item 102 (cn=test 08)(dn=i )(h323=2008)(e164=2008)(loc=.)(node=root)(pbx=<user filter="normal" cd-filter="normal" cfnr="15" busy-out="2"/>)(pbx=<device hw="2008"/>)(pbx=<presence/>)(guid;bin=05acc0dfe909d311b ad)( usn=52) mod cmd FLASHDIR0 add-item 102 (cn=extern)(h323=extern)(loc=.)(node=root)(pbx=<user filter="normal" cdfilter="normal"/>)(pbx=<pseudo type="gw"/>)(pbx=<device hw="extern"/>)(pbx=<presence/>)(guid;bin=013001afe909d311bd2f ad )(usn=53) mod cmd FLASHDIR0 add-item 102 (cn=test 09)(dn=Test 09)(h323=2009)(e164=2009)(loc=.)(node=root)(pbx=<user filter="normal" cdfilter="normal" cfnr="15" busy-out="2" 2013 ASCOM PAGE 22 OF 26

23 pwd="722c d0c ab6b0f52cef"/>)(pbx=<device hw="2009"/>)(pbx=<presence c="tel:"/>)(guid;bin=0588b5fbe909d311b ad)(usn=54) mod cmd FLASHDIR0 add-item 102 (cn=test 01)(dn=Test 01)(h323=2001)(e164=2001)(loc=.)(node=root)(pbx=<user filter="normal" cdfilter="normal" cfnr="15" busy-out="2" pwd="722c d0c ab6b0f52cef"/>)(pbx=<device hw="2001"/>)(guid;bin=003470b7e909d311b ad)(usn=55) mod cmd FLASHDIR0 add-item 102 (cn=test 11)(dn=Test 11)(h323=9911)(e164=9911)(loc=.)(node=root)(pbx=<user cfnr="15" busyout="2" pwd=" d0c ab6b0f52cef"/>)(pbx=<grp name="fe" mode="active"/>)(pbx=<device hw="9911"/>)(guid;bin=137606c6e909d311929a e02fd)(usn=57) mod cmd FLASHDIR0 add-item 102 (cn=test 25)(dn=Test 9925)(h323=9925)(e164=9925)(loc=.)(node=root)(pbx=<user/>)(pbx=<device hw="9925"/>)(guid;bin=a30d01abe909d3119a5e e02fd)(usn=58) mod cmd FLASHDIR0 add-item 102 (cn=test 29)(dn=Test 29)(h323=9929)(e164=9929)(loc=.)(node=root)(pbx=<user cfnr="15" busyout="2"/>)(pbx=<device hw="9929"/>)(guid;bin=ec01b608e909d31182ed e02fd)(usn=59) mod cmd FLASHDIR0 add-item 102 (cn=test 12)(dn=i )(h323=9912)(e164=9912)(loc=.)(node=root)(pbx=<user filter="normal" cd-filter="normal" cfnr="15" busy-out="2" pwd=" d0c ab6b0f52cef"/>)(pbx=<device hw="9912"/>)(pbx=<presence c="tel:"/>)(guid;bin=05b47759e909d311b ad)(usn=60) mod cmd FLASHDIR0 add-item 102 (cn=test 10)(dn=Test 10)(h323=9910)(e164=9910)(loc=.)(node=root)(pbx=<user cfnr="15" busyout="2" pwd=" d0c ab6b0f52cef"/>)(pbx=<device hw="9910"/>)(guid;bin=a67d7518e909d311929a e02fd)(usn=64) mod cmd FLASHDIR0 add-item 102 (cn=test 24)(dn=Test 9924)(h323=9924)(e164=9924)(loc=.)(node=root)(pbx=<user/>)(pbx=<device hw="9924"/>)(pbx=<presence s="open"/>)(guid;bin= e909d311b e02fd)(usn=65) mod cmd FLASHDIR0 add-item 102 (cn=miratel 6202)(dn=Miratel 6202)(h323=6202)(e164=6202)(loc=.)(node=root)(pbx=<user cfnr="15" busyout="2" pwd="762e d0c ab6b0f52cef"/>)(pbx=<device hw="6202"/>)(guid;bin=a4de81bbe909d311ab6d e02fd)(usn=68) mod cmd FLASHDIR0 add-item 102 (cn=miratel 6222)(dn=6222)(h323=6222)(e164=6222)(loc=.)(node=root)(pbx=<user/>)(guid; bin=2a7e47b2e909d311ab6d e02fd)(usn=69) mod cmd FLASHDIR0 add-item 102 (cn=miratel 6221)(dn=6221)(h323=6221)(e164=6221)(loc=.)(node=root)(pbx=<user/>)(guid; bin=aabcccbbe909d311ab6d e02fd)(usn=70) mod cmd FLASHDIR0 add-item 102 (cn=miratel 6223)(dn=6223)(h323=6223)(e164=6223)(loc=.)(node=root)(pbx=<user/>)(guid; bin=4f14daa6e909d311ab6d e02fd)(usn=71) mod cmd FLASHDIR0 add-item 102 (cn=miratel 6212)(dn=6212)(h323=6212)(e164=6212)(loc=.)(node=root)(pbx=<user/>)(guid; bin= e909d311ab6d e02fd)(usn=72) mod cmd FLASHDIR0 add-item 102 (cn=miratel 6213)(dn=6213)(h323=6213)(e164=6213)(loc=.)(node=root)(pbx=<user/>)(guid; bin=4a4e07d3e909d311ab6d e02fd)(usn=73) mod cmd FLASHDIR0 add-item 102 (cn=miratel 6231)(dn=6231)(h323=6231)(e164=6231)(loc=.)(node=root)(pbx=<user/>)(guid; bin=4534c05ee909d311ab6d e02fd)(usn=74) mod cmd FLASHDIR0 add-item 102 (cn=test 14)(dn=Test 14)(h323=9914)(e164=9914)(loc=.)(node=root)(pbx=<user cfnr="15" busyout="2" pwd=" d0c ab6b0f52cef"/>)(pbx=<grp name="fe" mode="active"/>)(pbx=<device hw="9914"/>)(pbx=<presence c="tel:"/>)(guid;bin=05c3cf8be909d311b ad)(usn=75) mod cmd FLASHDIR0 add-item 102 (cn=_admin_)(pbx=<user pwd=" f27079ecbc79cd5494f0ad310" 2013 ASCOM PAGE 23 OF 26

24 key=" aea3b8a9b78918d4fdb2a0"/>)(guid;bin=00446e72e909d311a AD)(usn=114) mod cmd FLASHDIR0 add-item 102 (cn=test 13)(dn=Test 13)(h323=9913)(e164=9913)(loc=.)(node=root)(pbx=<user cfnr="15" busyout="2" pwd=" d0c ab6b0ed2cef "/>)(pbx=<device hw="9913"/>)(guid;bin=4caae3eee909d311a e02fd)(usn=159) mod cmd FLASHDIR0 add-item 102 (cn=vm)(dn=vm)(h323=vm)(e164=1000)(loc=.)(node=root)(pbx=<user text="vm"/>)(pbx=<pseudo type="vm"><script/></pseudo>)(guid;bin=8fe8fd87e909d311814e e02fd)( usn=221) mod cmd FLASHDIR0 add-item 102 (cn=test 15)(dn=Test 15)(h323=9915)(e164=9915)(loc=.)(node=root)(pbx=<user cfnr="15" busyout="2" pwd=" d0c ab6b0f52cef "/>)(pbx=<device hw="9915"/>)(pbx=<presence c="tel:"/>)(guid;bin=05cc64b3e909d311b ad)(usn=245) mod cmd FLASHDIR0 add-item 102 (cn=fe)(dn=fe)(h323=9990)(e164=9990)(loc=.)(node=root)(pbx=<user/>)(pbx=< pseudo type="broadcast"/>)(pbx=<grp name="fe" mode="active"/>)(pbx=<device hw="9990"/>)(guid;bin=9a6fa1cde909d3118e e02fd)(usn=289) mod cmd FLASHDIR0 add-item 102 (cn=test 02)(dn=Test 02)(h323=2002)(e164=2002)(loc=.)(node=root)(pbx=<user filter="normal" cdfilter="normal" cfnr="15" busy-out="2" pwd="722c d0c ab6b0ed2cef "/>)(pbx=<device hw="2002"/>)(guid;bin=00cf6045e909d311b ad)(usn=300) mod cmd FLASHDIR0 add-item 102 (cn=1101)(dn=1101)(h323=1101)(e164=1101)(loc=.)(node=root)(pbx=<user fake="1101" url="1101" cfnr="15" busy-out="2" nodev="true"/>)(guid;bin=8ec103bde909d311ab6d e02fd)(usn=316) mod cmd FLASHDIR0 add-item 102 (cn=serak 9907)(dn=9907)(h323=9907)(e164=9907)(loc=.)(node=root)(pbx=<user cfnr="15" busy-out="2"/>)(pbx=<grp name="fe" mode="active"/>)(pbx=<device hw="9907"/>)(guid;bin=2d8a4b93e909d311ab6d e02fd)(usn=319) mod cmd FLASHDIR0 add-item 102 (cn=serak 9906)(dn=9906)(h323=9906)(e164=9906)(loc=.)(node=root)(pbx=<user cfnr="15" busy-out="2"/>)(pbx=<grp name="fe" mode="active"/>)(pbx=<device hw="9906"/>)(guid;bin=5e4b4415e909d311ab6d e02fd)(usn=320) mod cmd FLASHDIR0 add-item 102 (cn=serak 9905)(dn=9905)(h323=9905)(e164=9905)(loc=.)(node=root)(pbx=<user cfnr="15" busy-out="2"/>)(pbx=<grp name="fe" mode="active"/>)(pbx=<device hw="9905"/>)(guid;bin=ecfb6ac0e909d311ab6d e02fd)(usn=321) mod cmd FLASHDIR0 add-item 102 (cn=dect2)(pbx=<dect sysid=" " ac="1234" ac-mode="system" tones="0" kp="true" oem1="0x3ff" oem2="freq-eu" oem3="0" oem4="0x0"><coder model="g711a" frame="20"/><lcoder model="-" frame="60"/></dect>)(pbx=<pseudo type="dect"/>)(pbx=<user nodev="true"/>)(loc=.)(node=root)(hide=true)(guid;bin=90454c8fe909d31194e E02FD)(usn=571) mod cmd FLASHDIR0 add-item 102 (cn=dect)(pbx=<dect sysid=" " ac="1234" ac-mode="system" tones="0" kp="true" oem1="0x7f" oem2="freq-eu" oem3="0" oem4="0x0"><coder model="g711a" frame="20"/><lcoder model="-" frame="60"/></dect>)(pbx=<pseudo type="dect"/>)(loc=.)(node=root)(hide=true)(guid;bin=019fad78e909d311929a E02FD)(usn=605) mod cmd FLASHDIR0 add-item 102 (cn= )(dn= )(h323= )(e164= )(auth= )(pbx=<user pwd=" ac79cf7add588cf292fd3440d944bd5bedeee" admin="no"/>)(pbx=<gw name="dect" user-assigned="true" dsp="4201"/>)(guid;bin=c33259d6e909d31191ba00013e136794)(usn=622) mod cmd FLASHDIR0 add-item ASCOM PAGE 24 OF 26

25 (cn= )(dn= )(h323= )(e164= )(auth= )(pbx=<user pwd=" ac79cf7aed5344f0ad310b8780c8ab5b6b9ec" admin="no"/>)(pbx=<gw name="dect" user-assigned="true" dsp="4202"/>)(guid;bin=c4d94c05e909d31191ba00013e136794)(usn=623) mod cmd FLASHDIR0 add-item 102 (cn= )(dn= )(h323= )(e164= )(auth= )(pbx=<user pwd=" ac79cf6add54933ff5dd e452f" admin="no"/>)(pbx=<gw name="dect" user-assigned="true" dsp="4211"/>)(guid;bin=431464f7e909d3118bcb00013e136794)(usn=624) mod cmd FLASHDIR0 add-item 102 (cn= )(dn= )(h323= )(e164= )(auth= )(pbx=<user pwd=" ac79cf7a8d50f4f0ad310203a0d8ab5b6b9ec" admin="no"/>)(pbx=<gw name="dect" ipei=" " dsp="4203" subs="b3f1bc6433bf c8b9e9ae2f55"/>)(guid;bin=f398f03de909d311ab2a0 0013E136794)(usn=627) 2013 ASCOM PAGE 25 OF 26

26 References [1] Ascom Sweden AB Installation and Operation Manual, IP-DECT Base Station and IP-DECT Gateway (software version 6.1.x), TD 92579EN. Available from Ascom Technical Reference Library through authorized resellers. [2] BroadSoft, Inc BroadWorks Device Management Configuration Guide, Release Available from BroadSoft at broadsoft.com/xchange. [3] BroadSoft, Inc BroadWorks Redundancy Guide, Release Available from BroadSoft at broadsoft.com/xchange. [4] BroadSoft, Inc BroadWorks SIP Access Device Interoperability Test Plan, Release Available from BroadSoft at broadsoft.com/xchange. [5] BroadSoft, Inc BroadWorks Device Management Interoperability Test Plan, Release Available from BroadSoft at broadsoft.com/xchange ASCOM PAGE 26 OF 26