Programming Manual of ENFORCER Security System with GSM Auto Dialer from the House NSE :

Transcription

1 Operation Code Table: Sr. No Code Operation Page No. 1 of Hooter time (01 to 99 minute) 2 02 Bell time (01 to 99 minute) 3 03 Zone one type ( 1-Bell, 2-Delay, 3-Instant, 4-24H Instant, 5-Bypass, 6- Home Mode, 7-Silent-24 hour) 4 04 Zone two type ( 1-Bell, 2-Delay, 3-Instant, 4-24H Instant, 5-Bypass, 6- Home Mode, 7-Silent-24 hour) 5 05 Zone three type ( 1-Bell, 2-Delay, 3-Instant, 4-24H Instant, 5-Bypass, 6- Home Mode, 7-Silent-24 hour) 6 Zone Four Panic (Permanent) 7 Zone Five Fire (Permanent) 8 06 Auto Mode (enable-20/ disable-20) 9 07 Entry time (01 to 99 minute) Exit time (01 to 99 minute) New password Keypad lock time (01 to 99 second) Phone 1 Max 16 digits Phone 2 Max 16 digits Phone 3 Max 16 digits Phone 4 Max 16 digits Phone 5 Max 16 digits Real time setting (RTC) Date setting Auto arming time Message 1 recording (20 SECOND) (For Panic) Message 2 recording (20 SECOND) (For Fire) Message 3 recording (20 SECOND) (For Intruder) Play message 1 (20 SECOND) Play message 2 (20 SECOND) Play message 3 (20 SECOND) Epabx (on enter your extn. No / off press 99) Relay 1 ON/OFF ( 1 to ON 0 to OFF) ( To operate the any 220 V household equipment like AC or Light or anything) Relay 2 ON/OFF ( 1 to ON 0 to OFF) ( To operate the any 220 V household equipment like AC or Light or anything) Dialing attempts Message attempts Remote Programming (0 for No/ 1 for Yes) Ring Attempts Out from programming Mode ( please press #) Auto Disarm Time

2 Zone types: The User can program all the three zone in seven types as given below: Page No. 2of Bell: (When the zone is set as bell zone its mean, when that particular zone is break then it do not create the hooter but it s give you the bell indication if bell is attached with panel) 2. Instant: (When the zone is set as Instant zone its means, when that particular zone is break the hooters is ON only when the system is armed otherwise it do not give the alarm) Hr. Instant: (When the zone is set as 24hr. Zone then the particular zone work every time even the system is disarmed.) 4. Delay: (When the zone is set as Delay zone its means, it s give you the entry/ exit time to you & it s only work when the system is armed). 5. Bypass (When the zone is set as bypass zone, its do not work) 6. Home mode: (When the zone is set as Home zone then that particular zone only works when the system is completely armed.) 7. Silent Mode: (When the zone is set as Silent Zone, then that particular zone works like 24 hour panic zone without hootering.) Especially for heavy cash transaction places like bank & jewelry shop, where the any Robber come with the know how that they want money or just to shoot the person. Three very important features of our panel for Banking Industry: Suppose the zone of your panel become faulty (means the sensor become dead or some wiring is cut from somewhere) in that case you have to shut down the complete panel & you have to send your technician for that site immediate for repair that panel & up-to the time you reach the site, the bank is on complete risk without the security systems. 1. But when you use our panel then ( if any zone become the faulty or wire is break, just Disarm the system & the particular zone automatically becomes the bypass zone & rest of panel is working as it is when system is armed after the delay time.) Cont. on Page 3.

3 Page No. 3 of You can use the Keypad as well as Electronics Key to Arm or Disarm the Panel. 3. Duress Code: Means when you press this code along with password then the LCD show the system is disarmed but the dialing is start in silent mode. It is very useful when somebody pressurize you to disarm the system forcefully. (Use of Duress Code: in our systems duress code is 66. Then when you want to activate this feature then you have press: - password enter button for activate the silent dialing) Note for programming: 1. To enter in programming mode please press firstly * the LCD show Enter Password then press the password + # (enter). (E.g. If factory default password is 1234, then press *1234#) If the password is OK then LCD shows you the operation success & you enter into the programming mode otherwise operation is fail.) 2. After enter in programming mode please press the code & after that press the op-code as mention in the list. You can program everything after the entering in to programming mode without come out from it. Some example of programming: (A) For set the status of Zone 1: Please enter code 03 to select the Zone 1 and after the op-code for zone status by pressing 1/2/3/4/5 or 6 numbers. (For e.g. if you want to know the zone on Delay, you have press like that :) Firstly go into the programming mode by pressing * + password+#. Suppose the password is 1234 then: Press *1234# after that LCD show operation success & enter the op-code mean the password is OK then press 03 & after that press 2 for Delay zone & press the enter key (#) for confirm the programming). By doing the same you can change the status of any programmable zone to any status. (Bell/ delay/instant/ 24 instant/ bypass/ home zone) Cont. on Page 4..

4 Page No. 4of 6. (B) For set the Exit Time: Please enter the code 08 to select the exit time for all the delay zones, and after that press the two digit times (01 to 99 minutes) & press # key for confirm it. If the method of programming is OK then LCD show you the Operation Success otherwise Operation Fail. (For e.g. If you want to make the Exit delay time of 03 minutes, you have press like that :) Firstly go into the programming mode by pressing * + password+#. Suppose the password is 1234 then: Press * LCD show enter password, press 1234 & # after that LCD show operation success & enter the code 08 after that LCD show the current time, please press 03 & press# key. If the method of programming is OK then LCD show the operation success otherwise operation fails. (C) For set the Telephone No s: Please enter the code 11 & press the telephone/mobile no & press the # key for confirm. (Maximum16digit). (For e.g. if you want to program the mobile no , you have press like that :) Firstly go into the programming mode by pressing * +password+#. Suppose the password is 1234 then: Press * LCD show enter password, press 1234 & after that LCD show operation success & enter the code 11 after that enter the phone no & press # for confirm the no.) If the method of programming is OK then LCD show you the Operation Success otherwise Operation Fail. By doing the same you can change the any programming in the system. Always Remember: Always press the enter button (#) to confirm the programming. Cont. on Page 5..

5 Wiring Diagram for different Uses other the normal Zones. Page No. 5of 6. Wiring for fire zone: Wiring for Key Operation: Wiring for Relay operation: PCB F-12 V: positive of sensor PCB ARM: negative of Key Neutral comes from main on COM of PCB PCB GND: Negative of sensor PCB 12 V: Positive of Key. Wire from NO to Electrical Device. Connection of Wire on PCB: Please connect all wire on the PCB as well on the body of panel as mention on it according to zone or hooter or telephone. Note: please do not remove any connection which comes from factory for attach the both PCB in the panel. Note: 1. After the keypad is lock, and you want to arm or disarm the systems, you have to enter the password twice a time. First time to unlock the keypad & second time to change the status of system. 2. You can also use electronic key for arming/disarming the system beside of using key pad. For that please put the negative of key on ARM & positive on 12V on the PCB connector. 3. The same programming you can use when you program the system by telephone. Cont. on Page 6.

6 Page No. 6of 6. Technical Specification: 1. Operating Voltage: 220V AC/ 9-12V DC 2. Current Consumption of panel: Quiescent Current: 120 m Amp Max. (LCD off)/ Operating Current: 180 m AMP Max. (LCD ON) 3. Current consumption with hooter output: 700 m Amp (Including Internal Hooter + one External Hooter) 4. Maximum Load: 1.25 AMP (excluded hooter.) 5. Activation: Total 5 inputs: Three NO/NC Contact & one NC contact for panic & one Fire Sensor input NO. 6. Electrical Device Attachments: 2 Electrical Relay Contact NO. 7. Output: One Hooter Output. 8. Response time: 250 M. Sec. 9. Operating temp: -18 C to 55 C 10. Dimensions: 11 X 10 X Weight: Net Weight: 2Kg. approx without battery/ Gross weight with packing: 2.5 Kg approx 12. Mounting: Wall or Flat Surface. 13. Case Material: ABS resin Plastic 1 st Grade 14. Color: White.

7 Programming Manual of Rider-3005 ;JÅ5 YD l;:8d SM VMG SZT[ C{P display S[ p%z date l,bf C]VF VFTF C{P loz S]K ;DI % TL1FF SZ[P HA 30L R,G[,U[ TA * 1234 and Enter key SF 5 IF{U SZ[P.;;[ display 5Z Operation Success l,bf VFI[UFP (1234 is The Co. Default password) S]K ;DI AFN Enter Opp. Code l,bf VFI[UFP loz D{G]V, S[ VG];FZ SM0 0F,SZ programming SZ ;ST[ C{P 01. Hotter Time Change SZG[ S[ l,ˆ Hooter Time 1 Mint. To 99 Min. TS 0F, ;ST[ C{P IlN CD[ 20 ldg8 Hooter Time 0F,GF C{ TM ;A;[ 5C,[ Opp. Code Enter SF % IMU SZ[U[P.;L % SFZ SM0 02 NAFSZ Bell Time 1 sec. to 99 sec TS 0F, ;ST[ C{P 02. Zone Type Change SZG[ S[ l,ˆ Zone SM CD ;FT 5 SFZ ;[ program SZ ;ST[ C{P IlN zone 1 programming SZGL C{4 TM opp. Code 5Z Bell S[ l,i[ Enter NAFI [U[P Delay S[ l,i[ Enter NAFI [U[P Instant S[ l,i[ Enter NAFI [U[P 24 Hours Instant S[ l,i[ Enter NAFI [U[P By Pass S[ l,i[ Enter NAFI [U[P Home Mode S[ l,i[ Enter NAFI [U[P Silent 24 Hour l,i[ Enter NAFI [U[P.;L 5 SFZ Zone- 2 VF{Z Zone- 3 SM S DXo Opp. Code -04 VF{Z 05 0F,SZ program SZ ;ST[ C{P Delay Zone Type I[ Zone Type Only Armed CMG[ S[ AFN SFIÅ SZ[UFP I[ Enter & Exit Time NMGM N[UFP Programming Manual of Rider-3005 Instant Zone Type- I[ Zone Type EL Armed CMG[ S[ AFN SFIÅ SZ[UFP.;D[ l;oå Exit Time,[UFP By Pass Type -.;D[ zone SM. EL SFIÅ GCL SZ[UFP

8 24 Hours Instant Type- I[ Zone type Armed & Disarmed NMGM D[ SFIÅ SZ[UFP Silent 24 Hours Type- I[ Zone type Armed & Disarmed NMGM D[ SFIÅ SZ[UFP 5ZgT] Hooter GCL AH[UFP l;oå Dialing SZ[UFP Zone 4- I[ Fire Zone C{ 05. Auto Mode Enable / Disable SZG[ S[ l,i[- IlN l;:8d SM Automatic Armed or Disarmed SZGF C{ TM Auto Mode Enable SZGF CMUFP.;S[ l,i[ Opp. Code 5Z Enter Key NAFI [U[P.;L 5 SFZ.; 5 ls IF SM NMAFZF SZG[ 5Z Auto Mode Disable CM HFI[UFP 06. Auto Arming Time 0F,G[ S[ l,i[v IlN l;:8d SM ZFT SM 10:30 5Z Armed SZGF C{ TM Opp. Code 5Z Enter Key NAFI [U[P.;;[ l;:8d Automatic 10:30 AH[ Armed CM HFI[UFP Programming Manual of Rider Auto Disarming Time 0F,G[ S[ l,i[v IlN l;:8d SM ;]AC 08:30 5Z Disarm SZGF C{ TM Opp. Code 5Z Enter Key NAFI [U[P.;;[ l;:8d Automatic 8:30 AH[ Disarmed CM HFI[UFP

9 08. Enter & Exit Time 0F,G[ S[ l,i[v lhtg[ ;DI D[ VF% V%G[ 3Z4 VF lo;4 N]SFG4 Sd5GL SM AgN SZS[ AFCZ lgs,t[ C{ p;s[ l,i[ Exit Time 0F,U[ P H{;[v Exit Time 1 Mint. 0F,G[ S[ l,i[ Enter,.;L TZC lhtgl N[Z D[ VF5 N]SFG VYJF VF lo; BM, SZ l;:8d SM AgN SZ ;ST[ C{P.;S[ l,i[ Enter Time 0F,GF CMUFP H{;[v Enter Time 1 Mint. 0F,G[ S[ l,i[ Enter Key NAFGF CMUFP 09. Phone No. 0F,G[ S[ l,i[v VF%.;D[ Opp. Code 11 to 15 Telephone No./ Mobile No. 0F, ;ST[ C{ lh; 5Z Message VFI[UFP 10. For Date & Time Setting:- Current Time Set SZG[ S[ l,i[ Opp. Code 5Z 16+Current Time + Enter, Current Date Set SZG[ S[ l,i[ 17+Current Date+ Enter Key NAFI[P 11. For Record & Play Message:- VF5 V5GF D{;[H Opp. Code 19,20,21 5Z lzsfå0 SZ ;ST[ C{P H{;[:- 19+ Enter, 20+ Enter, 21+ Enter. Message No. 03 for Zone 1, Zone 2, Zone 3 and Temper Message No. 02 for Fire, Message No. 01 for Panic, Programming Manual of Rider EPABX Line System SL Setting:- IlN EPABX SL Extantion Line 5Z l;:8d,ufgf CM TM Opp. Code: (Extension No.) + Enter Key NAFI[P EPABX Code C8FG[ S[ l,i[ Opp. Code Enter Key NAFI[P 13. For Message Attempt:- CD V5G[ Telephone/ Mobile 5Z lhtgl AFZ D{;[H ;]GGF RFCT[ C{ TM p;s[ l,i[:--iln NM AFZ ;]GGF C{ TM Opp. Code Enter Key NAFI[P

10