M65-C COMPETITION. 65cc - 2 stroke - 6 speed - liquid cooled LUKS CENTRAL-LAGER. Opdateret pec

Transcription

1 M65-C COMPETITION - 2 stroke - 6 speed - liquid cooled Opdateret pec LUKS CENTRAL-LAGER Tlf E:Mail.. [email protected] Side 1 af 33

2 ENGINE CYLINDER Two-Stroke Single Cylinder Light alloy with nickel silicon carbide plated liner with7 scavenge ports plus double exhaust scavenge ports INTAKE DISTRIBUTION BORE STROKE DISPLACEMENT By 4 blade fiber carbon reed valve in engine block 44,50 mm 41,75 mm 64,93 cc COMPRESSION RATIO 15,5 +/- 0,5:1 MAX POWER CRANKSHAFT MAX POWER WHEEL MAX TORQUE CRANKSHAFT MAX RPM COOLING CARBURATOR LUBRIFICATION IGNITION STARTER CLUTCH TRANSMISSION TYPE PRIMARY TRANSMISSION SECONDARY TRANSMISSION CHAIN ALIGNMENT SPARK PLUG FUEL LUBRIFICATION OIL TYPE OIL TYPE DRY WEIGHT 16,7 Hp (12,3 kw) at rpm 15,2 Hp (11,2 kw) at rpm 9,8 Nm at rpm rpm Liquid cooled forced circulation by pump Dell Orto PHBL 24 with manual starter by lever Petrol with + 2% oil mixture sinthetic (Castrol TTS) Electronic magnetic flywheel with internal rotor D 36mm and microprocessor ignition timing management.external ignition coil. Ignition advance 33 +/- 2 a 4000 rpm By kick starter (backwards kick) Multiple disk type in oil bath 6 speed With helical gears Ratio sprocket/crown Z 21/74 = 3, speed = 11/40=3, speed = 15/37=2, speed = 18/34=1, speed = 20/30=1,50 5. speed = 23/28=1, speed = 25/27=1,08 By chain ½ x 3/16 roll 8,51mm (chain sprocket Z12 or Z13) 86 mm Champion C53 / NGK B105EGV M14x1,25 EURO unleaded NC R.O.N. 95 CASTROL TTS AGIP 2T or CASTROL 2T - TTS 13,2 kg OIL CAPACITY TRANSMISSION 0,44 kg tipe SAE 15W/40 Side 2 Side 2 af 33

3 ENGINE TYPE: M65-C Competition Liquid Cooled POWER - TORQUE - CONSUMPTION Max power at crankshaft ( ) : 12.3 kw ( = 16.7 Hp ) Max torque at crankshaft ) : 9.80 Nm POWER & TORQUE CURVES AT CRANKSHAFT - ENGINE 65-C (**) Torque [Nm] Power [Hp] Engine RPM [rpm] Pow er Torque Consumption The indicated performance values are to be considered as minimum values registrated according to MORINI FRANCO I S.p.A. standard specification RS140. The engine has been tested mounted with MORINI FRANCO I accessories and the registrated power, torque and consumption curves can therefore divert relatively dipending on the influence from using specific customized accesories. (especially air filter box and exhaust system) RADIATOR -Suggested radiator surface > 2,5 dm 2 (not screened) -Thermostat temperature operation range: AIR FILTER BOX -Sponge filter element saturated with 2-T oil, filter surface S = 2 dm 2 -Air entrance chamber volume V 1 > 1,5 dm 3 -Air exit chamber volume V 2 > 1,0 dm 3 EXHAUST SYSTEM- Enclosed drawing of suggested exhaust system Side 3 Side 3 af 33

4 UDSTØDNINGS DATA Side 4 Side 4 af 33

5 UDSTØDNING Mdl : code 0105 Udstødning -6M CRM.srl Tavle Udstødning Side 5 Side 5 af 33

6 BLOKKE CRANCKCASE Tavle A Side 6 Side 6 af 33

7 BLOKKE CRANCKCASE Tavle A Fig. No. Code Qty. Description A CLUTCH COVER GASKET A CYLINDER HEAD NUT A FLAT WASHER A OIL DRAIN SEAL A SCREW TE 8X10 A FLAT WASHER 6X11X1 A SCREW TCE 6X55 A SCREW TCE 6X50 A CASING COMPLET FM A CRANKCASE-COVER COUPLING A CYLINDER FIX.STUD BOLT A GEAR STOPPER LEVER PIN A SPACER FM A SET OF SEAL A SET OF GASKETS A SPRING WASHER D 8,4X32X2 A SILENT BLOCK REAR MOUNT A RONDELLE PLATE UNI 6592 INOX A SCREW A A SPRING WASHER DIN 982 INOX FLANGED SELF-LOCKING NUT Side 7 Side 7 af 33

8 KRUMTAP CRANKSHAFT Tavle B Side 8 Side 8 af 33

9 KRUMTAP CRANKSHAFT Tavle B Fig. No. Code Qty. Description B CAGE KBK 12X15X15 B CONNECTING ROD COMPLETE B FLYWHEEL KEY B BEARING C5H TN9 17X40X12 B DRIVE SHAFT SEAL B CRANKSHAFT FM 65CC COMPLETE B WASHER, CLUTCH CASING B CLUTCH DRIVE SHAFT SEAL Side 9 Side 9 af 33

10 CYLINDER TOP- STEMPEL CYLINDER HEAD - PISTON Tavle C Side 10 Side 10 af 33

11 CYLINDER TOP STEMPEL CYLINDER HEAD - PISTON Tavle C Fig. No. Code Qyy. Description C FLAT WASHER C CYLINDER HEAD NUT C WATER DRAIN SCREW, TE 8X10 C DISCHARGE GASKET C SPARK PLUGS CHAMPION C55 C HEAD-CYLINDER C SEAL C HEAD GASKET C HEAD+CYLINDER STUD BOLT C CYLINDER BASE GASKET 0, CYLINDER BASE GASKET 0, CYLINDER BASE GASKET 0,5 C PIN HOLDING RING C PIN C PISTON RING D44,5X1,9 C PISTON COMPLETE C CYLINDER + PISTON KIT COMPLETE C O-RING SEAL C SPROCKET 3X9,8 DRIVE ROLLER C SCREW C GASKET C ROLLER 3X11,8 C SPRING WASHER Side 11 Side 11 af 33

12 KICHSTARTER STARTING SHAFT Tavle D Side 12 Side 12 af 33

13 KICHSTARTER STARTING SHAFT Tavle D Fig. No. Code Qty. Description D ARTICULATED STARTING LEVER D CIRCLIP D CIRCLIP DIN 471 D TRUST WASHER FOR STARTING GEAR D STARTING GEAR D STARTER STOPPER PLATE D STOPPER PLATE SETSCREW D SPRING SPACER D STARTING SHAFT RETURN SPRING D SLEEVE SPRING D STARTING SLEEVE D STARTER SHAFT D ROLLER CAGE 16X20X10 D SCREW SEAL D WASHER 0,4 D WASHER 0,5 D STARTING SHAFT O-RING Side 13 Side 13 af 33

14 VANDPUMPE WATER PUMP Tavle E Side 14 Side 14 af 33

15 VANDPUMPE WATER PUMP Tavle E Fig. No. Code Qty. Description E SEAL SCREW E SCREW TE 6X10 E SCREW TLE 5X25 E CLAMP E WATER DELIVERY PIPE, TO CYLINDER E CLAMP D18 E WATER PUMP BODY WITHOUT BLOW-BY E WATER PUMP DRIVE SHAFT E PUMP DRIVE GEAR PIN E CASING GASKET E WATER PUMP SEAL 8X16X10 E WASHER 0,5 E PUMP DRIVE GEAR E CUP 4M E WATER PUMP IMPELLER Side15 Side 15 af 33

16 GEAR SKIFTER SELECTOR DRUM Tavle F Side 16 Side 16 af 33

17 GEAR SKIFTER SELECTOR DRUM Tavle F Fig. No. Code Qty. Description F ROLLER FOR GEAR STOPPER PLATE F ROLLER FOR GEAR STOPPER PLATE F GEAR STORRER PLATE F ROLLER HOLDING WASHER F SCREW TE 5X25 FULL THREAD F GEAR STOPPER LEVER SPRING F GEAR STOP LEVER F CIRCLIP D8 F RATCHET PAWL SPRING F GEAR SELECTOR COMPLETE F SHIFTER PLATE RETURN SPRING F WASHER 0,5 F CIRCLIP FOR ROD SHOULDER F FORK ROD SMALL F GEAR CONTROL FORK F SELECTOR DRUM COMPLETE 6M F GEAR SHIFTER SHAFT SEAL F GEARSHIFT FORK SPINDLE F GEAR CONTROL FORK 5-6 GEAR F GEAR LEVER 65CC F WASHER LEVER HOLDER Side 17 Side 17 af 33

18 PRIMÆR GEAR AKSEL MAIN SHAFT Tavle G Side 18 Side 18 af 33

19 PRIMÆR GEAR AKSEL MAIN SHAFT Tavle G Fig. No. Code Qty. Description G BEARING 6202 C3 15X35X11 G BEARING SHOULDER HOLDER G WASHER D5 G SCREW TCE 5X18 G PRIMARY SHAFT CASE 12X16X10 G PRIMARY SHAFT COMPLETE 6M G TH-SPEED GEAR G GROOVED WASHER G SNAP RING G ND-SPEED GEAR G RD 4TH- SPEED SLIDING GEAR G TH - SPEED GEAR G WASHER G PRIMARY SHAFT,- 1 ST SPEED G WASHER D5 Side 19 Side 19 af 33

20 SEKUNDÆR GEAR AKSEL COUNTER SHAFT Tavle H Side 20 Side 20 af 33

21 SEKUNDÆR GEAR AKSEL COUNTER SHAFT Tavle H Fig. No. Code Qty. Description H SNAP RING HALF-PULLEY H OIL DRIP PAN (RH CASING) H OIL DRIP PLATE H CIRCLIP SECOND. SHAFT H SCREW H ST-SPEED GEAR H SPRING WASHER H SLIDING GEAR FOR 5 TH - SPEED H SNAP RING H INDENTED WASHER H SECONDARY SHAFT 6M H RD-SPEED GEAR H TH-SPEED GEAR H SLIDING GEAR FOR 6TH- SPEED GEAR H ND-SPEED GEAR H SECONDARY SHAFT BEARING 12X32X10 C3 H SECONDARY SHAFT CASE 20X26X16 H SEAL 19X30X6,5 H SPACER H Z 12 SPROCKET 65CC Z 13 SPROCKET 65CC Z 14 SPROCKET 65CC H SPRING WASHER H CUP 6M H RETAINING RING,SECON. SHAFT BEARING H SECONDARY SHAFT COMPLETE Side 21 Side 21 af 33

22 KOBLING CLUTCH UNIT Tavle I Side 22 Side 22 af 33

23 KOBLING CLUTCH UNIT Tavle I Fig. No. Code Qty. Description I THRUST BLOCK COMPLETE (GAS GAS) I SCREW TE 6X25 I SAFETY PLATE I SPRING RETAINING PLATE I CLUTCH SPRING I NUT M10 I SPRING WASHER, ZINC-PLTD YELLOW I NUT STOPPING PLATE I CLUTCH INNER HUB I DRIVEN PLATE I DRIVEN SPRING PLATE I DRIVEN PLATE I PLATE THRUST DISC VERSION 05 I WASHER 0,08 I COMPLETE PRIMARY GEAR PAIR I RIVET I CLUTCH BELL I PRIMARY GEAR PAIR I PRIMARY GEAR SPACER I HEXAGON NUT M10X1,25 I ENGINE SPROCKET KEY I O-RING SEAL FOR ENGINE SPROCKET I SAFETY PLATE / NUT M10 (131003) LÅSEBLIK TIL KOBLING Side 23 Side 23 af 33

24 GA TÆNDING FLYWHEEL MAGNETO Tavle L Side 24 Side 24 af 33

25 TÆNDING FLYWHEEL MAGNETO Tavle L Fig. No. Code Qty. Description L STARTER IDLE GEAR L WASHER L LAY SHAFT CASE 12X16X10 L CIRCLIP D12 L SPACER CLUTCH BELL S6-GA65 L FLYWHELL COMPETITION L NUT M8 L COIL + PLUG COMPLETE S6/COM-GA65 L DIGITAL CONTROL UNIT S6/C-GA65 L WASHER D8,2X14X1.8 L CABLE FOR CONTROL UNIT L SPARK PLUG RUBBER L SCREW TCE 4X20 L SPARK PLUG CAP L SPARK PLUG RUBBER L.40 C SPARK PLUG CHAMPION C55 Side 25 Side 25 af 33

26 DÆKSEL CRANKCASE HALVES COVERS Tavle M Side 26 Side 26 af 33

27 DÆKSEL CRANKCASE HALVES COVERS Tavle M Fig. No. Code Qty. Description M SCREW TCE 6X25 M PLATE WASHER 14X10X1,5 M CLUTCH COVER M O-RING SEAL FOR ROD M OIL DIPSTICK M SCREW TCE 6X20 M SCREW TCE 6X40 M FLYWHEEL COVER M RUBBER FLYWHEEL COVER M WASHER D6 M HYDRALIC PISTON CLUTCH COVER M CONNECTION CLUTCH COVER M FLYWHEEL COVER RUBBER PLASTIC UNDER TÆNDINGS DÆKSEL Side 27 Side 27 af 33

28 KARBURATOR Tavle N ** Karburator beskrivelse se tavle P Side 28 Side 28 af 33

29 KARBURATOR Tavle N Fig. No. Code Qty. Description N REED VALVE N CARBURETTOR CONNECTION N SCREW TCE 6X25 N SPLIT WASHER D6 N WASHER N CLIMP CARBURATTOR N COUPLING RUBBER N CARBURETTOR 24 PHBL R.2869 ** Karburator beskrivelse se tavle P Side 29 Side 29 af 33

30 FLANCER Tavle O Side 30 Side 30 af 33

31 FLANCER Tavle O Fig. No. Code Qty. Description O NUT H6 M6 O O-RING SEAL ADLER 36X1,5 O WASHER D6 O SCREW TCE 6X25 O LOCK UP FLANCE FOR OIL MIXER Side 31 Side 31 af 33

32 KARBURATOR Dellorto PHBL 24 BS. Reg Tavle P Side 32 Side 32 af 33

33 KARBURATOR Dellorto PHBL 24 BS. Reg Tavle P Fig. No. Code Description x 64 GASSPJÆLD (40) X 08 GASNÅL (D) X 28 NÅLESTYR AQ (264) X 02 HOVEDDYSE (100) X 02 DYSE TOMGANG (50) X 02 DYSE (60) X 33 SVØMMERNÅL X 80 SVØMMER KIT TOPDÆKSEL GUMMI STILLESKRUE GASFJEDER LÅSESKIVE LÅSERING O-RING FOR TOPDÆKSEL SKRUE CHOKER KIT FOR LUFTSKRUE O-RING KIT FOR TOMGANGSSKRUE SKVULPEPLADE BENZIN FILTER DÆKSEL FOR BENZINFILTER SKRUE FOR DÆKSEL O-RING FOR BUNDKAR BUNDKAR STIFT FOR SVØMMER O-RING FOR BUNDSKRUE BUNDSKRUE PAKNINGSSÆT Side 33 Side 33 af 33