Easier System Maintenance. Better Water Balance. Enhanced Swimmer Comfort

Transcription

1 Easier System Maintenance Better Water Balance Enhanced Swimmer Comfort

2 Specially formulated ph neutral. Reduces sanitizer consumption. Helps maintain stable ph. Removes food source for algae growth. Not affected by UV or evaporation. Buffers total alkalinity. Compatible with all forms of sanitization. Reduces eye and skin irritation. Enhances swimmer comfort. Improves water clarity. Helps maintain better water balance. Gives the water a soft, silky feel. Safe and easy to use. Reduces operating cost 35 50% on average. Does not contain cyanuric acid. Ocean Breeze Re-Support residual should range between ppm. Initial treatment use 2 pounds per 1000 gallons of pool water. Initial treatment should be added in two doses, with one half the amount being added in each application. Test the water balance and Ocean Breeze Re-Support level and adjust accordingly. Increases chlorine effectiveness. Prevents unnecessary loss of chlorine to the ultraviolet rays of the sun. Reduces chlorine consumption. Stabilizes pool water and saves operating costs. Backwash or clean filter. Initial treatment use 1 2/3 lbs. (26 oz. by wt.) per 10,000 gallons of pool water. To add UV Shield, make a slurry of powder in a pail of water. With the pump running, pour the slurry into the skimmer. This treatment is sufficient to produce the recommended cyanurate concentration of 20 ppm. Case of 12 x 1 lb. Bag An inhibited acid cleaning system specifically recommended for Salt Cells. Quickly loosens and removes oils, combined organic matters, and calcium deposits from Salt Cells. Can safely be disposed of down drains or sewers. Add one pound of Salt Cell Cleaner to 3 gallons of fresh water and mix the solution thoroughly in an appropriate size container. Stir until the Salt Cell Cleaner is totally dissolved. Immerse Salt Cell in the solution for 15 to 30 minutes. Case of 12 x 1 lb. bag Case of 4 x 10 lb. pail, 20 lb. pail, 45 lb. pail

3 Surrounds and coagulates microscopic particles as small as 2 microns. Nonmetallic, non-staining and non-foaming. Not affected by shock treatments. Formulated ph neutral. Removes both organic matter and dirt through filtration. Eliminates need for algaecides. Compatible with all sanitizing systems. Crystallizes and removes metals from pool water through the filter. Removes unsightly stains from pool surfaces and equipment of the pool. Helps to lower calcium hardness. Removes Iron, Copper, Silver and Manganese metals. Non-chlorine oxidizer. Will not raise chlorines to unacceptable levels. Removes all chloramines (combine chlorine). Compatible with chlorine, bromine, copper-silver ionization and chlorine generators. Reduces sanitizer consumption. Helps maintain sparkling blue water. Prohibits algae occurrence by physically removing spores. Time separation between shock application and treatment not required. Reduces operational cost. Initial treatment use 14 ounces per 10,000 gallons of pool water directly with the pump and filter running. Maintenance treatment use 4 ounces per 10,000 gallons of pool water weekly. Spring and Fall maintenance treatment use 2 ounces per 10,000 gallons of pool water weekly. Compatible with all types of filtration. Removes metallic stains. Removes scale. Prevents staining and protects plumbing and equipment. Adjust ph to Apply over entire pool surface. Keep filter running continuously for 48 hours. For best results water temperature should be above 60 degrees. Initial treatment use 1 quart per 10,000 gallons of pool water if metals are present. Maintenance treatment use 3 ounces per 10,000 gallons of pool water weekly. Swimmers should wait 8 hours before entering pool once treatment is executed. Easy to use. Enhances swimmer comfort. Restores sparkle and clarity to dull water. Will not bleach or fade vinyl liners. Allows quick access to the pool; 15 minutes usually. 1 pound treats 10,000 gallons of pool water. Broadcast over pool surface with pump and filter running. Case of 12 x 1 lb. bag Case of 12 x 1 Qt. Case of 12 x 1 Qt.

4 Is the stain Metallic or Organic? This on site test was developed to answer this question and provide a step-by-step solution for removal. Step 1: Begin by taking a plastic bottle and filling it with rocks or sand and water. Replace the cap and attach a sponge with rubber bands to the bottle. The bottle must become submersible. Step 2: Soak the sponge with OCEAN BREEZE METAl MIRAClE and place it on the stain under the pool or spa water. Allow the OCEAN BREEZE METAl MIRAClE to work on the stain for five minutes. If the area near the sponge turns yellow, it is an organic stain and should be treated with an algae removal approach. If the pool or spa finish returns to the original color, the stain is metallic and will be easily removed. Refer to Step 4 for the METAl MIRAClE Treatment Guide. If there is no change in the appearance of the stain, it is a metallic stain with multiple layers. Resoak the sponge in OCEAN BREEZE METAl MIRAClE and place it on the stain for fifteen minutes. If the pool or spa finish returns to the original color, refer to Step 4 for the METAl MIRAClE Treatment Guide. If the stain is still present, re-soak the sponge in OCEAN BREEZE METAl MIRAClE and place it on the stain for thirty minutes. 99% of the time, the finish will return to the original color in thirty minutes or less. Refer to Step 4 for the METAl MIRAClE Treatment Guide. Step 3: Raise the pool or spa water above the normal level to avoid a bathtub ring look to the finish. Step 4: Treat the water using OCEAN BREEZE METAl MIRAClE and Sponge Test time table. Five Minutes: 1 Quart OCEAN BREEZE METAl MIRAClE per 10,000 gallons of water. Fifteen Minutes: 1 Quart OCEAN BREEZE METAl MIRAClE per 5,000 gallons of water. Thirty Minutes: 1 Quart OCEAN BREEZE METAl MIRAClE per 2,500 gallons of water. Continue running the pump and filter for three days, frequently checking the filter pressure and backwashing or cleaning as necessary. METAl MIRAClE lifts the metal stain from the pool or spa surface and changes it into a crystal that is removed from the water by the filter. The water may turn milky indicating the METAl MIRAClE is working faster than the filter. Continue filtering until the water clears. OCEAN BREEZE METAl MIRAClE should be used with a ph at 7.5 or above. It is not affected by Cyanuric Acid levels. Calcium will be lowered to ppm. METAl MIRAClE is safe to use on all pool or spa surfaces. It will remove the metal from the water before it will remove the stain.

5 1,000 5,000 7,500 10,000 13,500 20,000 25,000 30,000 40,000 50, GOOD BETTER BEST PARTS PER MILLION GALLONS

6 Ocean Breeze Salt Support. Specially formulated for salt chlorine generation systems. Ocean Breeze Salt Support is specially formulated for use with salt chlorine generation systems. The patented chemistry is designed to assist with ease of maintenance and protect your pool s equipment from corrosion while extending the life of the salt conversion cells. Ocean Breeze Salt Support provides better water balance by buffering alkalinity and ph, removes food source for algae growth and protects against the unnecessary loss of chlorine to UV rays of the sun. Ocean Breeze Salt Support provides enhanced swimmer comfort and gives the water a soft, silky feel. Ocean Breeze Salt Support is easy to use and will improve water clarity while assisting the amount of chlorine produced through the salt conversion cells. 421 Ann St. N.W. Grand Rapids, Michigan OB