2014 Speed Concept fit guide 2014 SPEED CONCEPT FIT GUIDE
|
|
- Jewel Foster
- 7 years ago
- Views:
Transcription
1 2014 Speed Concept fit guide 2014 SPEED CONCEPT FIT GUIDE
2 Fitting a tri bike Fitting a triathlon bike is a multi-step process that must be performed in the correct sequence to achieve the proper fit. Whether you re new to fitting a bike or have experience fitting road bikes, this guide will help you perform the fit steps in the correct order. Please note that the new Speed Concept geometry is no different from the original Speed Concept, and the sizing follows much the same process as before. Note: This process applies to all MY14 Speed Concept bikes except the 7.0. To fit the 7.0, follow Step 1 and use the size chart to determine the appropriate frame size. Then use standard fit and sizing practices to determine appropriate stem length, rise, and spacers.
3 Fit steps, in order 1. Measure elbow pad stack, then reach 2. Measure base bar stack, then reach 3. Use sizing chart to find frame size and stem 4. Determine saddle height, then position Getting started To complete Steps 1 and 2, you ll need to get the customer on a bike. We recommend that you perform these measurements with your customer on a size cycle. If you don t have a size cycle, you may perform this step using a stock triathlon bike off your floor (estimate the approximate frame size by eye), or use your customer s existing tri bike if available. This may not be the final frame size appropriate for your customer, but it will get you started.
4 Step 1: Measure elbow pad stack, then reach All measurements assume center of the pad on the top surface. PAD REACH PAD STACK Easy way to measure pad stack -Measure from pad to ground -Measure from BB to ground -Subtract BB to ground number
5 Step 2: Measure base bar stack, then reach All measurements assume end of bar at the brake lever insertion point. BASE BAR REACH BASE BAR STACK Easy way to measure base bar stack -Measure from end of bar to ground. -Measure from BB to ground -Subtract BB to ground number -Find closest stem option
6 Step 3: Use size chart to determine frame size and stem 1. Find the column(s) that include desired pad reach. Start with mid-pad ranges (the top row of reach values). Draw a vertical line down from the column(s) 2. Find the row closest to desired pad stack. Draw a horizontal line rightward from the row. 3. Any intersection(s) of reach column and stack row that fall within a monospacer block = correct frame size. Colors inside the monospacer block indicate which monospacer with (+5) or without the pad wing spacer achieves the desired stack. Discard any intersections that don t fall within a monospacer block. If no stack + reach combination intersects within a monospacer block, expand your pad stack selection to include the pad-range row. If that doesn t produce the desired result, expand your stack selection to include the full-range row. 4. Check base bar stack and reach of the frame solution(s) for closest match to desired measurements. If necessary, expand your pad stack selection as noted above. 5. Record frame and stem solutions at bottom of chart.
7 Example ❶ ❷ ❸ XS S M L XL Low-Near Low-Far Medium-Near Medium-Far High-Near High Far Low-Near Low-Far Medium-Near Medium-Far High-Near High Far Low-Near Low-Far Medium-Near Medium-Far High-Near High Far Low-Near Low-Far Medium-Near Medium-Far High-Near High Far Low-Near Low-Far Medium-Near Medium-Far High-Near High Far mid-pad FIND YOUR ARM PAD REACH pad range full range FIND YOUR ARM PAD STACK CHECK THE BASEBAR STACK ❹ AND REACH ❺ HERE'S THE FRAME SIZE XS S M L XL AND STEM SIZE Low-Near Low-Far Medium-Near Medium-Far High-Near High Far Low-Near Low-Far Medium-Near Medium-Far High-Near High Far Low-Near Low-Far Medium-Near Medium-Far High-Near High Far Low-Near Low-Far Medium-Near Medium-Far High-Near High Far Low-Near Low-Far Medium-Near Medium-Far High-Near High Far
8 Step 4: Determine saddle height, then position Start with the frame and stem solution indicated by the size chart, with the appropriate pad and bar positioning. SADDLE SETBACK/OFFSET SADDLE HEIGHT Easy way to measure saddle setback/offset -Place back wheel against wall -Measure from wall to saddle tip -Measure from wall to BB -Subtract BB measurement -Negative Number = Saddle Setback -Positive Number = Saddle Forward Offset
9 Seatpost length There are two available lengths: 275mm and 335mm. Seatpost offset The 9 Series seatpost is reversible and comes in two offsets. 15mm: most customers will use this 50mm: used for extreme tri or UCI TT compliant position The 7 Series seatpost is reversible and comes in a 17mm offset.
DIRECTIONS FOR SETTING UP LABELS FOR MARCO S INSERT STOCK IN WORD PERFECT, MS WORD AND ACCESS
DIRECTIONS FOR SETTING UP LABELS FOR MARCO S INSERT STOCK IN WORD PERFECT, MS WORD AND ACCESS WORD PERFECT FORMAT MARCO ITEM #A-3LI - 2.25 H x 3W Inserts First create a new document. From the main page
More informationSPEC YOUR SPEEDMAX CF SLX EXACTLY HOW YOU WANT IT WITH THESE BASE CONFIGURATIONS
COST-FREE OPTIONS SPEC YOUR SPEEDMAX CF SLX EXACTLY HOW YOU WANT IT WITH THESE BASE CONFIGURATIONS Please note: Due to the customised nature of these options, any changes made to the Speedmax CF SLX standard
More informationC10 ultra high-modulus aero carbon tubing, integrated seat clamp, integrated head tube, water bottle mount
18 24 3081 Norcom Straight - Matt Reed Edition Sizes Color(s) Matte Carbon Main frame Rear triangle Fork Crankset Bottom bracket Pedals Front Derailleur Rear Derailleur Shifters Cassette Chain Wheelset
More informationPrinting Letters Correctly
Printing Letters Correctly The ball and stick method of teaching beginners to print has been proven to be the best. Letters formed this way are easier for small children to print, and this print is similar
More informationVT SERIES. Owners Manual VARIABLE TRAVEL MOUNTAIN BIKE
VT SERIES Owners Manual VARIABLE TRAVEL MOUNTAIN BIKE Multi purpose, Enduro, Trail ride, Light Freeride mountain bike Single pivot, linkage operated rear shock rear suspension Manitou Swinger SPV Air rear
More informationCreate Charts in Excel
Create Charts in Excel Table of Contents OVERVIEW OF CHARTING... 1 AVAILABLE CHART TYPES... 2 PIE CHARTS... 2 BAR CHARTS... 3 CREATING CHARTS IN EXCEL... 3 CREATE A CHART... 3 HOW TO CHANGE THE LOCATION
More informationLab #4 - Linear Impulse and Momentum
Purpose: Lab #4 - Linear Impulse and Momentum The objective of this lab is to understand the linear and angular impulse/momentum relationship. Upon completion of this lab you will: Understand and know
More informationSCOTT SCALE CARBON BIKE OWNER S MANUAL 2015. www.scott-sports.com
www.scott-sports.com SCOTT SCALE CARBON All rights reserved 2014 SCOTT Sports SA SCOTT Sports SA 17 Route du Crochet 1762 Givisiez Switzerland BIKE OWNER S MANUAL 2015 Distribution: SSG (Europe) Distribution
More informationTooling List 17mm Socket 17mm Wrench 24mm Wrench 26mm Wrench 3/8 Drive Ratchet Torque Wrench
Thank you for purchasing the CorkSport Rear Adjustable Camber Arms. By replacing your OEM camber arms with the CorkSport Adjustable Camber Arms, you will be able to dial in your suspension with +/- 5 degrees
More informationYour New Frog Bike. Congratulations on purchasing a new bike and thank you for choosing Frog!
Your New Frog Bike Congratulations on purchasing a new bike and thank you for choosing Frog! We know that you must be raring to go but before you do there s a few little things still to do to get you up
More information1. The volume of the object below is 186 cm 3. Calculate the Length of x. (a) 3.1 cm (b) 2.5 cm (c) 1.75 cm (d) 1.25 cm
Volume and Surface Area On the provincial exam students will need to use the formulas for volume and surface area of geometric solids to solve problems. These problems will not simply ask, Find the volume
More informationRoof Tutorial. Chapter 3:
Chapter 3: Roof Tutorial The majority of Roof Tutorial describes some common roof styles that can be created using settings in the Wall Specification dialog and can be completed independent of the other
More informationTotal Access. Stage 2 IFI accredited equipment. ceptional
Total Access Stage 2 IFI accredited equipment ceptional Features and Benefits Raised iconography on main console controls Colour contrasted belt and deck Laser cut numbers for easy seat positioning Colour
More informationFigure 1. An embedded chart on a worksheet.
8. Excel Charts and Analysis ToolPak Charts, also known as graphs, have been an integral part of spreadsheets since the early days of Lotus 1-2-3. Charting features have improved significantly over the
More informationUniversal Gauge Measuring System USERS MANUAL
Universal Gauge Measuring System 2002 Chief Automotive Technologies, Inc. Chief s Limited One-Year Warranty & Liability CHIEF'S LIMITED ONE-YEAR WARRANTY & LIABILITY Chief Automotive Technologies, Inc.
More informationHow to Measure for Exterior Shutters
Tools you may need: Measuring Tape Pencil Paper Ladder How to Measure for Exterior Shutters Measuring your windows properly is an important step to ensure your installation goes both smoothly and that
More information3D Drawing. Single Point Perspective with Diminishing Spaces
3D Drawing Single Point Perspective with Diminishing Spaces The following document helps describe the basic process for generating a 3D representation of a simple 2D plan. For this exercise we will be
More informationSpeed-Mat Rectangle Cutter
Speed-Mat Rectangle Cutter 1 Honeycomb baseboard. 2 Left hold down. 14 3 Bottom hold down. 4 4 Left / right rule. 8 5 8 5 Left / right rule pointer. 1 6 Top / bottom rule. 7 Top / bottom rule pointer.
More informationPerspective and Space
Perspective and Space Space: The element of art referring to the emptiness or area between, around, above, below, or within objects. FOREGROUND - Part of the picture plane that appears closest to the viewer
More informationMicrosoft Excel 2010 Charts and Graphs
Microsoft Excel 2010 Charts and Graphs Email: training@health.ufl.edu Web Page: http://training.health.ufl.edu Microsoft Excel 2010: Charts and Graphs 2.0 hours Topics include data groupings; creating
More informationBIRT: A Field Guide to Reporting
BIRT: A Field Guide to Reporting x:.-. ^ 11 Diana Peh Alethea Hannemann Nola Hague AAddison-Wesley Upper Saddle River, NJ Boston Indianapolis San Francisco New York Toronto Montreal London Munich Parts
More informationGYPSUM AREA SEPARATION FIREWALLS GA-620-2011
GYPSUM AREA SEPARATION FIREWALLS GA-620-2011 GA-620-2011 Copyright 2011 Gypsum Association All rights reserved. Printed in U.S.A. Characteristics, properties, or performance of materials or systems herein
More informationMEASURING WHEEL ALIGNMENT
MEASURING WHEEL ALIGNMENT 2003-04 WHEEL ALIGNMENT Specifications & Procedures - Hummer - H2 Steering and vibration complaints are not always the result of improper alignment. One possible cause is wheel
More informationSubtracting Negative Integers
Subtracting Negative Integers Notes: Comparison of CST questions to the skill of subtracting negative integers. 5 th Grade/65 NS2.1 Add, subtract, multiply and divide with decimals; add with negative integers;
More informationSample Table. Columns. Column 1 Column 2 Column 3 Row 1 Cell 1 Cell 2 Cell 3 Row 2 Cell 4 Cell 5 Cell 6 Row 3 Cell 7 Cell 8 Cell 9.
Working with Tables in Microsoft Word The purpose of this document is to lead you through the steps of creating, editing and deleting tables and parts of tables. This document follows a tutorial format
More information39HQ Airovision Air Handling Units
39HQ Airovision Air Handling Units Mounting instructions CONTENTS 1 - TRANSPORT AND LIFTING INSTRUCTIONS... 3 1.1 - General... 3 1.2 - Transport and storage... 3 1.3 - Roof edge protection during transport
More informationHorizontal Mini Blinds Installation Guide
Horizontal Mini Blinds Installation Guide We make it easy! BTG 468298 EN_ rev0614 For more safety information: 1-866-662-0666 or.www.healthcanada.gc.ca/blindcords Before starting Your new Blinds To Go
More informationRoof Tutorial. Chapter 3:
Chapter 3: Roof Tutorial The first portion of this tutorial can be completed independent of the previous tutorials. We ll go over some common roof styles that can be created using settings in the Wall
More informationLesson 4.3: Using the VLOOKUP Function
Lesson 4.3: Using the VLOOKUP Function Excel 2003 provides two lookup functions that you can use to quickly retrieve information from a table. The functions are called HLOOKUP (horizontal lookup) and VLOOKUP
More informationKWIK SEW 'S SEWING ROOM SERIES
KWIK SEW 'S SEWING ROOM SERIES MEASURING & BASIC ALTERATIONS Use the expertise behind KWIK SEW patterns to help achieve a perfect fit! Measuring the body and choosing the correct size pattern. A PERFECT
More informationBedford, Fowler: Statics. Chapter 4: System of Forces and Moments, Examples via TK Solver
System of Forces and Moments Introduction The moment vector of a force vector,, with respect to a point has a magnitude equal to the product of the force magnitude, F, and the perpendicular distance from
More informationAtomic Force Microscope and Magnetic Force Microscope Background Information
Atomic Force Microscope and Magnetic Force Microscope Background Information Lego Building Instructions There are several places to find the building instructions for building the Lego models of atomic
More informationWWW.SCOTT-SPORTS.COM SCOTT SCALE USER MANUAL 2016
SCOTT SCALE USER MANUAL 2016 All rights reserved 2015 SCOTT Sports SA Distribution: SSG (Europe) Distribution Center SA, P.E.D. Zone C1, Rue du Kiell 60, 6790 Aubange, Belgium v5.1/03082015 WWW.SCOTT-SPORTS.COM
More informationTasks to Move Students On
Maths for Learning Inclusion Tasks to Move Students On Part 1 Maths for Learning Inclusion (M4LI) Tasks to Move Students On Numbers 1 10 Structuring Number Maths for Learning Inclusion (M4LI) Tasks to
More informationPRODUCT GUIDANCE FABRIC STANDS
PRODUCT GUIDANCE FABRIC STANDS FORMULATE FABRIC DISPLAY SYSTEM Description Formulate back walls are aluminium structures easy to assemble with graphics printed onto fabric graphic socks that fit snugly
More informationPartnerships Implementing Engineering Education Worcester Polytechnic Institute Worcester Public Schools
Partnerships Implementing Engineering Education Worcester Polytechnic Institute Worcester Public Schools Supported by: National Science Foundation Simple Machines: 4.G.2 _ Inclined Planes and Pulleys Grade
More informationThis document fully describes the 30 Day Flexibility Challenge and allows you to keep a record of your improvements in flexibility.
Welcome to the StretchTowel 30 Day Flexibility Challenge! You can Be More Flexible in 30 days by following our stretching program for 10 minutes a day. The best part is that you can stretch using the StretchTowel
More informationInformation Literacy Program
Information Literacy Program Excel (2013) Advanced Charts 2015 ANU Library anulib.anu.edu.au/training ilp@anu.edu.au Table of Contents Excel (2013) Advanced Charts Overview of charts... 1 Create a chart...
More informationNumber Wheeler P/N Description Set Rex P/N Notes
1 607051 Base 1 A050 2 607052 Motor Cover 1 A052 3 600778 Socket Hd Cap Screw (M8x60) 2 4 607053 Scrap Receiver 1 A053 5 607054 Tank Upper Cover 1 A054 6 607055 Oil Pot 1 A055 7 607056 Strainer 1 A056
More informationThis file contains 2 years of our interlibrary loan transactions downloaded from ILLiad. 70,000+ rows, multiple fields = an ideal file for pivot
Presented at the Southeastern Library Assessment Conference, October 22, 2013 1 2 3 This file contains 2 years of our interlibrary loan transactions downloaded from ILLiad. 70,000+ rows, multiple fields
More informationTurboCAD Architectural
TurboCAD Architectural Version 15 Getting Started Guide IMSI/Design LLC, US 100 Rowland Blvd. Novato. CA 94945, USA Tel: +1-415-878-4000 Fax: +1-415-897-2544 Web Site www.imsisoft.com www.turbocad.com
More informationShort Interval Production Schedule Research
Short Interval Production Schedule Research Background Nationals Park has multiple highly repeatable tasks that can be scheduled as efficiently as possible by the development of a Short Interval Production
More informationSYSTEM COMPLETE SPEEDMAX CF SLX. 2 Speedmax CF SLX System Complete
SYSTEM COMPLETE SPEEDMAX CF SLX 2 Speedmax CF SLX System Complete GREAT PERFORMANCES DON T HAPPEN BY CHANCE. ALL THE RIGHT ELEMENTS HAVE TO ADD UP. COMPLETE PLANNING. COMPLETE TESTING. COMPLETE TRAINING.
More informationSession 7 Bivariate Data and Analysis
Session 7 Bivariate Data and Analysis Key Terms for This Session Previously Introduced mean standard deviation New in This Session association bivariate analysis contingency table co-variation least squares
More informationMicrosoft Office PowerPoint 2003. Creating a new presentation from a design template. Creating a new presentation from a design template
Microsoft Office PowerPoint 2003 Tutorial 2 Applying and Modifying Text and Graphic Objects 1 Creating a new presentation from a design template Click File on the menu bar, and then click New Click the
More informationSuperform Products Ltd.
TYPICAL CORNER REINFORCING NOTE : SEE ENGINEERED REBAR SCHEDULES SUPPLIED BY THE MANUFACTURER STEEL REINFORCEMENT WALL CORNER 90 Copyright 2012 Sept. 2012 5.1.1 Rebar Spacing 6" 12" Max. Load LB./FT. 2000
More informationINSTRUCTION MANUAL AND PARTS LIST MODEL 14-10
VERTICAL BAND SAWS INSTRUCTION MANUAL AND PARTS LIST MODEL 1-10 DAKE/PARMA WHEN ORDERING PARTS GIVE COMPLETE SERIAL NUMBER OF MACHINE GIVE PART NUMBER AND NAME GIVE AMOUNT REQUIRED Unless the above data
More informationComputer Training Centre University College Cork. Excel 2013 The Quick Analysis Tool
Computer Training Centre University College Cork Excel 2013 The Quick Analysis Tool Quick Analysis Tool The quick analysis tool is new to Excel 2013. This tool enables the user to quickly access features
More informationCreate a Poster Using Publisher
Contents 1. Introduction 1. Starting Publisher 2. Create a Poster Template 5. Aligning your images and text 7. Apply a background 12. Add text to your poster 14. Add pictures to your poster 17. Add graphs
More informationYears after 2000. US Student to Teacher Ratio 0 16.048 1 15.893 2 15.900 3 15.900 4 15.800 5 15.657 6 15.540
To complete this technology assignment, you should already have created a scatter plot for your data on your calculator and/or in Excel. You could do this with any two columns of data, but for demonstration
More informationThis document will describe how you can create your own, fully responsive. drag and drop email template to use in the email creator.
1 Introduction This document will describe how you can create your own, fully responsive drag and drop email template to use in the email creator. It includes ready-made HTML code that will allow you to
More informationMore than shelving & racking. All for your storage demands.
More than shelving & racking. All for your storage demands. CONTENTS SELECTIVE PALLET RACKING A cost effective storage system providing direct access to all pallet. SLOTTED ANGLE SHELVING Simple, cost-effective
More informationTECHNICAL BULLETIN. Meritor WABCO Cab Leveling Valves and Chassis Leveling Valves. How the Cab Leveling and Chassis Leveling Valves Work
Revised 02-00 TECHNICAL BULLETIN Meritor WABCO Cab Leveling Valves and Chassis Leveling Valves This technical bulletin covers both cab and chassis leveling valves manufactured by Meritor WABCO. While the
More informationassembly instructions
assembly instructions 1 // this guide is for Urban Chic gents & ladies. // this guide is for Urban Chic gents & ladies. 2 1 x ph screwdriver 2 x 10mm spanners 1 x 15mm spanners 1 x 13mm spanners 1 x 6mm
More informationROSA Rapid Office Strain Assessment. Michael Sonne, MHK, CK. sonnemw@mcmaster.ca
ROSA Rapid Office Strain Assessment Michael Sonne, MHK, CK. sonnemw@mcmaster.ca Rapid Office Strain Assessment ROSA is a picture based posture checklist designed to quantify exposure to risk factors in
More informationHow to build a Pizza Oven in 4 days
How to build a Pizza Oven in 4 days Preparation day (slab) 1. Foundation 1500 deep x 1300 wide x 75mm deep Required 20 bags cement pre mix. If you already have a concrete base, you save this prep day DAY
More informationI NTERFACE CABLE ADAPTER MODULE
I NTERFACE CABLE ADAPTER MODULE The Interface Cable Adapter Module (ICAM) has two basic uses. First, it enables you to run shielded cable between the industrial sensor interface module (SIM) and the weather
More informationROUND(cell or formula, 2)
There are many ways to set up an amortization table. This document shows how to set up five columns for the payment number, payment, interest, payment applied to the outstanding balance, and the outstanding
More informationArm Replacement Right Chair Tools: Large Phillips (cross-tip) Screwdriver 1 person: ~5 minutes
Arm Replacement Tools: Large Phillips (cross-tip) Screwdriver 1. Activate seat height lever to maximum length, and then tip chair over for access to the arm brackets on the underside of the seat. 2. Locate
More informationIntroduction to Dashboards in Excel 2007. Craig W. Abbey Director of Institutional Analysis Academic Planning and Budget University at Buffalo
Introduction to Dashboards in Excel 2007 Craig W. Abbey Director of Institutional Analysis Academic Planning and Budget University at Buffalo Course Objectives 1. Learn how to layout various types of dashboards
More information3D Drawing. Single Point Perspective with Diminishing Spaces
3D Drawing Single Point Perspective with Diminishing Spaces The following document helps describe the basic process for generating a 3D representation of a simple 2D plan. For this exercise we will be
More informationI BEAM TRACK INSTALLATION
PDQ 0/700 FESTOON SYSTEM INSTALLATION AND MAINTENANCE INSTRUCTIONS INTRODUCTION The PDQ Festoon System was designed to run on one of three sizes of I-beams: S x., S8 x 8. and S x.. System trolleys must
More informationSolving Systems of Linear Equations Graphing
Solving Systems of Linear Equations Graphing Outcome (learning objective) Students will accurately solve a system of equations by graphing. Student/Class Goal Students thinking about continuing their academic
More informationPrecision Vise Combinations
Precision Vise Combinations PanaVise vises and work holding tools have hundreds of uses limited only by your imagination! Each vise allows the head to Tilt, Turn & Rotate and position your work anywhere
More informationExcel 2007: Basics Learning Guide
Excel 2007: Basics Learning Guide Exploring Excel At first glance, the new Excel 2007 interface may seem a bit unsettling, with fat bands called Ribbons replacing cascading text menus and task bars. This
More informationExcel 2007 - Using Pivot Tables
Overview A PivotTable report is an interactive table that allows you to quickly group and summarise information from a data source. You can rearrange (or pivot) the table to display different perspectives
More informationPerforming Simple Calculations Using the Status Bar
Excel Formulas Performing Simple Calculations Using the Status Bar If you need to see a simple calculation, such as a total, but do not need it to be a part of your spreadsheet, all you need is your Status
More informationPhysics 201 Homework 8
Physics 201 Homework 8 Feb 27, 2013 1. A ceiling fan is turned on and a net torque of 1.8 N-m is applied to the blades. 8.2 rad/s 2 The blades have a total moment of inertia of 0.22 kg-m 2. What is the
More informationStreet-Lynx. Reilly MotorSports, Inc. Installation Manual
Street-Lynx By Reilly MotorSports, Inc. Installation Manual 1 1- Begin by removing your original rear suspension disconnect your brake lines, E-brake cables, and remove the driveshaft. To prevent fire
More informationWorking with the new enudge responsive email styles
Working with the new enudge responsive email styles This tutorial assumes that you have added one of the mobile responsive colour styles to your email campaign contents. To add an enudge email style to
More informationTessellating with Regular Polygons
Tessellating with Regular Polygons You ve probably seen a floor tiled with square tiles. Squares make good tiles because they can cover a surface without any gaps or overlapping. This kind of tiling is
More informationBasic Pivot Tables. To begin your pivot table, choose Data, Pivot Table and Pivot Chart Report. 1 of 18
Basic Pivot Tables Pivot tables summarize data in a quick and easy way. In your job, you could use pivot tables to summarize actual expenses by fund type by object or total amounts. Make sure you do not
More informationExcel 2013 - Using Pivot Tables
Overview A PivotTable report is an interactive table that allows you to quickly group and summarise information from a data source. You can rearrange (or pivot) the table to display different perspectives
More information2013 Getting Started Guide
2013 Getting Started Guide The contents of this guide and accompanying exercises were originally created by Nemetschek Vectorworks, Inc. Vectorworks Fundamentals Getting Started Guide Created using: Vectorworks
More informationHoles & Selective Laser Sintering
SLS is one of the most accurate 3D printing processes. The process has a layer thickness of 0.1mm. This is the thickness with which a new layer is added to each part. In any direction therefore the maximum
More informationElectrical Wiring Technical Bulletin
Electrical Wiring Technical Bulletin Overview In general, SIP construction is easier and more cost effective when things are planned and thought out before the panels are manufactured. This process will
More informationIf you know exactly how you want your business forms to look and don t mind
appendix e Advanced Form Customization If you know exactly how you want your business forms to look and don t mind detail work, you can configure QuickBooks forms however you want. With QuickBooks Layout
More informationx x y y Then, my slope is =. Notice, if we use the slope formula, we ll get the same thing: m =
Slope and Lines The slope of a line is a ratio that measures the incline of the line. As a result, the smaller the incline, the closer the slope is to zero and the steeper the incline, the farther the
More informationBLACKBOARD 9.1: Text Editor
BLACKBOARD 9.1: Text Editor The text editor in Blackboard is a feature that appears in many different areas, but generally has the same look and feel no matter where it appears. The text editor has changed
More informationUnderstand the Sketcher workbench of CATIA V5.
Chapter 1 Drawing Sketches in Learning Objectives the Sketcher Workbench-I After completing this chapter you will be able to: Understand the Sketcher workbench of CATIA V5. Start a new file in the Part
More information"Excel with Excel 2013: Pivoting with Pivot Tables" by Venu Gopalakrishna Remani. October 28, 2014
Teaching Excellence and Innovation 1 Pivot table Pivot table does calculations with criteria Data should be arranged as : Field names in the first rows, records in rows No blank rows or blank columns should
More informationPrepared by Graham from SuperPro August 2011
Understanding di Steering and Wheel Alignment Angles Prepared by Graham from SuperPro August 2011 Remember:- Tyre Wear Patterns Tell The Technician A Story Provide Vital Information For Determining Final
More informationSpreadsheet - Introduction
CSCA0102 IT and Business Applications Chapter 6 Spreadsheet - Introduction Spreadsheet A spreadsheet (or spreadsheet program) is software that permits numerical data to be used and to perform automatic
More informationProduct Data Sheets. Belt Conveyor System
Product Data Sheets Belt Conveyor System Belt Conveyor System Belt Driven Conveyors the cost effective solution for transporting unit loads. Texam Limited s range of powered belt conveyors is designed
More informationRittal s Comprehensive Family Of... NETWORK RACK SOLUTIONS
Rittal s Comprehensive Family Of... NETWORK RACK SOLUTIONS STANDARD & ECONOMICAL BasicRack A complete low-cost, high-quality basic equipment management system. Design Six web channel holes per side allow
More information2.9 WINDOW & DOOR BUCKS
2.9 WINDOW & DOOR BUCKS Bucks provide attachment surfaces for windows and doors while holding back concrete from these openings during concrete placement. Mark the center and edges of openings as you place
More informationExercise 9-6 Creating a Window Family
Exercise 9-6 Creating a Window Family Estimated Time: File: 10 minutes ex8-5, generic model wall based.rft This exercise reinforces the following skills: Standard Component Families Templates We want to
More informationE-Bike Conversion Kits Installation Manual Front Wheel
E-Bike Conversion Kits Installation Manual Front Wheel Contents ( 一 )Getting started... Page 3 ( 二 )Tools List. Page 4 ( 三 )Removing and Installation of the wheel.. Page 5 ( 四 )Install the hand brake.....
More informationSize & Range. for windows & doors. Company
Size & Range for windows & doors A Company B General information windows and doors Sizes This catalogue contains all Airlite s standard sizes for windows and doors. These are the ones that we make every
More informationCompetitive Cyclist Fit Calculator
Nothing is really more important for creating a great cycling experience than matching yourself---your body, your goals, and your dreams---to the right bike. Some will tell you that there is one perfect
More informationHighline Excel 2016 Class 26: Macro Recorder
Highline Excel 2016 Class 26: Macro Recorder Table of Contents Macro Recorder Examples in this video... 2 1) Absolute Reference Macro: Format report that always has the same number of columns and rows...
More informationCREATING A 3D VISUALISATION OF YOUR PLANS IN PLANSXPRESS AND CORTONA VRML CLIENT
CREATING A 3D VISUALISATION OF YOUR PLANS IN PLANSXPRESS AND CORTONA VRML CLIENT 20-25 Minutes This topic is for users of PlansXpress Total Toolkit Edition. To upgrade to PlansXpress Total Toolkit, call
More informationTechnical handbook Panel Anchoring System
1 Basic principles of sandwich panels 3 Design conditions 4 Basic placement of anchors and pins 9 Large elements (muliple rows) 10 Small elements (two rows) 10 Turned elements 10 Slender elements 10 Cantilevering
More informationLunette 2 Series. Curved Fixed Frame Projection Screen. User s Guide
Lunette 2 Series Curved Fixed Frame Projection Screen User s Guide Important Safety and Warning Precautions Please follow these instructions carefully to ensure proper maintenance and safety with your
More informationPLACING STRUCTURAL BEAMS THAT SUPPORT COMPLEX ROOF SURFACES
INTRO This article will discuss how to model structural steel wide flange beams supporting complex roof surfaces. The first half of this article describes how to model structural beams that curve and undulate
More informationPowerPoint Tables / Charts / Graphs
PowerPoint Tables / Charts / Graphs Open PowerPoint: Click on Start (located on the Taskbar at the bottom) Click on Programs Click on Microsoft PowerPoint Click on the Microsoft PowerPoint icon (located
More informationINSTRUCTIONS. FLHR/C/S (Road King) FRONT END LOWERING KIT 1WARNING -J03242 REV. 10-19-04. General. Removal (Left and Right Forks) Kit Number 54614-05
INSTRUCTIONS -J04 REV. 0-9-04 General FLHR/C/S (Road King) FRONT END LOWERING KIT This kit is designed for installation on 00 and later FLHR/C/S Model Motorcycles. Road King models use the conventional
More information2014 FURNITURE. www.samsonitefurniture.com (844) 218-7049
www.samsonitefurniture.com (844) 218-7049 Manufacturing specifications are subject to change without notice. Dimensions refer to packing capacity and are approximate. California Proposition 65 Warning:
More informationCreating an Excel XY (Scatter) Plot
Creating an Excel XY (Scatter) Plot EXCEL REVIEW 21-22 1 What is an XY or Scatter Plot? An XY or scatter plot either shows the relationships among the numeric values in several data series or plots two
More informationTested to BS 6375: Part 1: 1989 and achieved a weathertightness classification of 2000 Pa (Special)
THE B6 GLAZING SYSTEM GLAZING SYSTEMS FOR SEPTEMBER 2013 THE B6 HEEL BEAD SEAL SECURITY GLAZING SYSTEM Page 1 DESCRIPTION The B6 Heel Bead Seal Security Glazing System is suitable for installing all types
More information