Quick Start Guide. Industrial Managed Gigabit Ethernet PoE+ Switch LPH2004A-2GSFP

Transcription

1 LPH2004A-2GSFP Industrial Managed Gigabit Ethernet PoE+ Switch Quick Start Guide Has (4) PoE+ 10/100/1000-Mbps twisted-pair and (2) SFP Gigabit ports. Customer Support Information Order toll-free in the U.S.: Call BBOX (outside U.S. call ) FREE technical support 24 hours a day, 7 days a week: Call or fax info@blackbox.com

2 1. Specifications For complete specifications, please see the user manual or the product data sheet for this switch. 1. Go to 2. Enter the part number (LPH2004A-2GSFP) in the search box: 3. Click on the Resources tab on the product page, and select the document you wish to download. 2. Features Has (4) PoE+ 10-/100-/1000-Mbps copper access ports and (2) Gigabit SFP ports. Operates in extreme temperatures of -40 to +158 F (-40 to +70 C). 2. What s Included Your package should contain the following items. If anything is missing or damaged, contact Black Box Technical Support at or info@blackbox.com. Industrial Managed Gigabit Ethernet PoE+ Switch - 4-Port RJ-45, 2-Port SFP (2) dust covers (installed on SFP slots to protect the electronic circuitry) (5) dust covers (installed on RJ-45 slots to protect the electronic circuitry) Console cable DIN-rail mounting kit Wallmounting kit Console cable (6) M3 x 5 flat-head screws This printed quick start guide Page blackbox.com

3 3. Hardware Description Figure 1-1 shows the Industrial Managed Gigabit Ethernet PoE+ Switch s front panel. Table 1-1 describes its components Figure 1. Front panel. 1. Reset button 8. Console port 2. PWR status LED 9. Link/Act LED for Gigabit LAN ports 3. PWR1 LED 10. Speed LED for LAN ports 4. PWR2 LED 11. PoE indicators for LAN ports 5. Ring Master status LED 12. Link/Act LED for SFP ports 6. Ring status LED 13. SFP ports 7. Fault relay LED 14. Gigabit LAN ports blackbox.com Page 3

4 4. Hardware Installation STEP 1: Installing the Switch on a DIN Rail or Wall Refer to the illustrations below to mount the switch on a DIN rail or wall. Figure 2. DIN rail installation. Figure 3. Wallmount installation. Page blackbox.com

5 STEP 2: Network connection. The switch provides standard Ethernet ports. According to the link type, the switch uses CAT3, 4, 5, 5e UTP cables to connect to any other network devices (PCs, servers, switches, routers, or hubs). Refer to the user manual for cable specifications. STEP 3: Wiring The switch supports dual redundant power supplies. The connections for PWR1, PWR2, and RELAY are located on the terminal block. Figure 4. Terminal block. STEP 3A: Insert the negative/positive wires into the V+/V- terminals, respectively. STEP 3B: To keep the DC wires from pulling loose, user a small flat-blade screwdriver to lighten the wire-clamp screws on the front of the terminal block connector. Relay contact The two sets of relay contacts on the 6-pin terminal block connector are used to detect userconfigured events. The two wires attached to the fault contacts form an open circuit when a user-configured event is triggered. If a user-configured event does not occur, the fault circuit remains closed. Grounding Grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the ground connection from the ground screws to the grounding surface prior to connecting devices. After installing the switch, the green Power LED should light blackbox.com Page 5

6 Table 1. LPH2004A-2GSFP indicators. Component (3) Power LEDs: (1) Ring Master LED Description PWR lights when PWR is on. PWR1 lights when DC power module 1 is activated. PWR2 lights when DC power module 2 is activated. Lights when Ring is enabled. Blinking when ring structure is broken. (1) Fault LED Power failure or port disconnected. (1) PoE LEDs Lights when the port is using PoE+. 10/100/1000BASE-T(X) Gigabit PoE ports: LINK/ACT LEDs Speed ON when the port link is connected. Blinking when data is being transmitted. Lights green when port link speed is 1000 Mbps. Lights amber when port link speed is 100 Mbps. OFF when port link speed is 10 Mbps. SFP ports: LINK ACT LEDs Lights when port link is connected. Blinking when data is being transmitted. Page blackbox.com

7 5. Configuration 1. Launch Internet Explorer and type in the IP address of the switch. The default static IP address is Login in with the default user name and password (both are admin). The following screen appears. For more information on configuring or operating the switch, see the user manual. Figure 5. Login screen. Resetting To reboot the switch, press the Reset button for 2 3 seconds. To restore the switch configurations back to the factory defaults, press the Reset button for 5 seconds blackbox.com Page 7

8 PoE+ Pin Definition Table 3-2. PoE pin definition. Pin 10/100BASE-T(X) PSE RJ-45 port Pin 1000BASE-T PSE RJ-45 port 1 TD+ with PoE power input + 1 BI_DA+ with PoE power input+ 2 TD- with PoE power input + 2 BI_DA- with PoE power input+ 3 RD+ with PoE power input - 3 BI_DB+ with PoE power input - 6 RD- with PoE power input - 4 BI_DC+ 4 Not used 5 BI_DC- 5 Not used 6 BI_DB- with PoE power input - 7 Not used 7 BI_DD+ 8 Not used 8 BI_DD- Page blackbox.com

9 NOTES blackbox.com Page 9

10 NOTES Page blackbox.com

11 NOTES blackbox.com Page 11

12 Chapter Black Box Tech Support: FREE! Live. 24/7. Tech support the way it should be. Great tech support is just 60 seconds away at or blackbox.com. About Black Box Black Box provides an extensive range of networking and infrastructure products. You ll find everything from cabinets and racks and power and surge protection products to media converters and Ethernet switches all supported by free, live 24/7 Tech support available in 60 seconds or less. Copyright Black Box Corporation. All rights reserved. Black Box and the Double Diamond logo are registered trademarks of BB Technologies, Inc. Any third-party trademarks appearing in this manual are acknowledged to be the property of their respective owners. LPH2004A-2GSFP, version 1 Page blackbox.com