English. Please read before use. Chase. Chase 2. Select 1/8. Program. Chase 3. Select 9/16. Chase 4. Midi / Rec. Chase 5. Auto / Del.

Transcription

1 Step/time Blackout Step PROG Auto trigger BANK Bank Chase 1 >> Scene 8 Chase A Select 1/8 B Select 9/16 PAGE SELECT 12 30S 0.1S 10Min SPEED Program Chase 3 Midi / Rec Chase 4 Auto / Del Chase 5 Music / Bankcopy Chase 6 Tapsync / Display Blackout 0 FADE TIME USER'S MANUAL English DMX DJ Chase 2 Music trigger 8888 >> 1 SCENES SCANNERS Please read before use

2

3 Contents Features 1 General Instructions 2 1. Overview Front View Rear View 6 2. Operation Guide Program Enable Programming Scenes Scene Editing Scanner Copy Scene Copy Delete a Scene Delete all Scenes Bank Copy Programming Chases Program a bank of scenes into a Chase Add a Step Delete a Step Delete a Chase Delete all Chases Running Scenes Manual Mode Auto Mode Music Mode 24 Improvement and changes to specifications, design and this manual, may be made at any time without prior notice. All rights reserved. 2.5 Running Chases Manual Mode Auto Mode Music Mode MIDI Operation MIDI Channel Setting Implementation 28 Technical Specifications 29

4 Features Thank you for your purchase of this product by Eliminator. This DMX DJ features include: 192 DMX channels, 12 scanners of 16 DMX channels 30 banks of 8 programmable scenes 6 chases of 240 programmed scenes from 30 banks 8 faders for manual control Chasing speed and Fade Time of Auto programs(scenes and chases) under control Fade Time control over all DMX channel Blackout master Manual override Built-in microphone for Music triggering MIDI control over banks, chases and Blackout Power failure memory NOTE: A knowledge of MIDI and DMX is required to fully utilize this unit. 1

5 General Instructions Read the instruction in this manual carefully and thoroughly, as they give important information regarding safety during use and maintenance. Keep this manual with the unit, in order to consult it in the future. If the unit is sold or given to another operator, make certain that it always has its manual, to enable the new owner to read about its operation and relative instructions. Warnings DO NOT make any inflammable liquids, water or metal objects enter the unit. Should any liquid be spilled on the unit, DISCONNECT the power supply to the unit immediately. STOP using the unit immediately In the event of serious operation problems and either contact your local dealer for a check or contact us directly. DO NOT open the unit--there are no user serviceable parts inside. NEVER try to repair the unit yourself. Repairs by unqualified people could cause damage or faulty operation. Contact your nearest dealer. Cautions This unit is NOT intended for home use. After having removed the packaging check that the unit is NOT damaged in any way. If in doubt, DON'T use it and contact an authorized dealer. Packaging material (plastic bags, polystyrene foam, nails, etc.) MUST NOT be left within children's reach, as it can be dangerous. This unit must only be operated by adults. DO NOT allow children to tamper or play with it. NEVER use the unit under the following conditions: In places subject to excessive humidity. In places subject to vibrations or bumps. In places with a temperature of over 45 C /113 F or less than 2 C/35.6 F. Protect the unit from excessive dryness or humidity (ideal conditions are between 35% and 80%). DO NOT dismantle or modify the unit. 2

6 1. Overview 1.1 Front View SCANNERS SCENES Blackout 1 7 Step PROG SEC Page A Step/time 8888 Music trigger Auto trigger BANK Chase 1 Chase Scene Bank Chase 2 30S Program Page B 4 10 Page Select MIN 6 12 Chase 3 Midi Rec Chase 4 Auto Del Chase 5 Music Bankcopy Chase 6 Tapsync Display DC-1216 DMX OPERATOR SPEED FADE TIME BLACKOUT R 0 3

7 1. Overview 1.1 Front View 1. Scanner Buttons(1-12) 12 scanners of 16 DMX channels & fader control Scanners DMX channels Fader control LED Scanners DMX channels Fader control LED Press a scanner button to turn on manual fader control. Press the scanner button again to turn off fader control. The LED besides the button lights or goes out to indicate this selection. 4

8 1. Overview 1.1 Front View 2. Scene Buttons 3. Segment Display 4. Bank Buttons(Up/Down) 5. Chase Buttons(1-6) 6. Program Button 7. MIDI/Rec Button 8. Auto/Del Button 9. Music/Bank Copy 10. Blackout Button 11. Tap Sync/Display 12. Fade Time Slider 13. Speed Slider 14. Page Select Button 15. Faders Press the scene buttons to load or stored your scenes. There are a maximum of 240 programmable scenes. Shows the current activity or programming state. Press the Up/Down buttons to select a bank from 30 banks. Used to select your programmed chase consisting a maximum of 240 scenes Used to activate Program mode. Used to control MIDI operation or to record programs. Used to activate Auto mode or to delete scenes and chases. Used to activate Music mode or to create scenes and chase programs. Used to disable channel output. Used to create a standard beat or to change the values display between % and 255. Used to adjust the Fade Time. Fade Time is the amount of time it takes for a fixture(scanner) to move from one position to another, for the dimmer to fade in or fade out. Used to adjust the speed at which the scenes will chase. Used to select faders for the fixture between Page A(1-8) and Page B (9-16). This faders are used to control the intensity of channel 1-8 or channel 9-16 depending upon the selected page. 5

9 1. Overview 1.2 Rear View MIDI IN 1=Ground 2=Data - 3=Data + DMX POLARITY SELECT 1=Ground 2=Data + 3=Data - DMX OUT DC INPUT +9~12V, 300mA min MIDI IN 2. DMX Polarity Select 3. DMX Out 4. DC Input Receives MIDI data. Used to select DMX polarity. This connector sends your DMX value to the DMX fixture or DMX pack. DC 9-12V, 300mA min. 6

10 2. Operation Guide GENERAL This unit allows you to program 12 scanners of 16 DMX channels, 30 banks of 8 programmable scenes, 6 chases of 240 programmed scenes using 8 faders and other function buttons. Up to 8 scenes can be programmed into a bank, and the amount of 240 programmed scenes can be stored into a chase and the scenes can be triggered by Music, Auto, Tap Sync, MIDI and Manual. Display Information The Segment Display consists of 4 digits. The first digit shows the active chase number(1-6), the second digit shows the active scene number(1-8), and the third and forth digits show the active bank number(01-30). During Auto mode, a highlight in the lower right corner of the Segment Display next to " Auto trigger" indicates its selection. During Music mode, a highlight in the upper right corner of the Segment Display next to " Music trigger" indicates its selection. During Blackout mode, a fast blinking light indicates its selection in the upper left corner of the Segment Display next to " Blackout". During Program mode, a fast blinking light indicates its selection in the lower left corner of the Segment Display next to " PROG.". 2.1 Program Enable Step/time Blackout Step PROG Chase Scene Bank Program Music trigger Auto trigger When the power is turned on, this unit enters Manual mode automatically. Press the Program button for three seconds to activate Program mode, a fast blinking light in the Segment Display next to "PROG." indicates its selection. 7

11 Operation Guide 2.2 Programming Scenes 1. Enter Program mode. Scanner buttons Press the Scanner button to turn on its fader control, which is indicated by the lit LED. You may select several scanners at a time by tapping of these Scanner buttons, so you can assign several fixtures at a time with this unit Create a desired scene using the faders. The DMX value is 0 when the fader is fully down(bottom) and 255 when it is fully up(top). 4. If necessary, you may tap the Page Select button to control the second set of 8 DMX channels. MIDI/Rec 5. ce the scene is satisfactory, tap the MIDI/Rec button to program this scene into memory. 8

12 2. Operation Guide 2.2 Programming Scenes BANK 6. Tap the Bank Up/Down button to select the bank you want to store your scene into. There are total 30 banks you can select, you may store up to 8 scenes into each bank. SCENE BUTTONS Tap the Scene button to store your scene, all LEDs and the Segment Display will flash three times briefly indicating this operation, then the Segment Display will show the bank and the scene. Scanner buttons Repeat steps 3-7until all desired scenes have been programmed into memory. Tap the Scanner button again to turn off its fader control. To assign another scanner(fixture), you may tap the corresponding Scanner button to turn on its fader control, then you may begin your programming again. 9

13 2. Operation Guide 2.2 Programming Scenes Program 9. If you wish not continue your programming, press and hold down the Program button for three seconds to exit Program mode, the blinking light in the Segment Display goes out indicating this selection. EXAMPLE: Program 8 scenes with channel 1-8 at full in sequence into bank 2 and assign these scenes to scanner Program enable. 2. Tap the Scanner 2 button to turn on its fader control. 3. Tap the Page Select button to select Page A. 4. Push Fader 1 to the top position. 5. Tap the MIDI/Rec button. 6. Select bank 2 using Bank Up/Down button. 7. Tap the Scene 1 button to store the first scene. 8. Repeat steps 4-7 until all 8 scenes have been programmed into bank Tap the Scanner 2 button again to turn off its fader control. 10. Press the Program button for 3 seconds to exit Programming mode. 10

14 2. Operation Guide Scene Editing 1. Program enable. 2. Tap the Bank Up/Down button to select the bank that contains the scene you wish to edit. BANK SCENE 3. Select the scene you want to edit by tapping its Scene button Use the Faders to make your desired adjustments. 11

15 2. Operation Guide Scene Editing MIDI/Rec 5. ce you've made your changes, tap the MIDI/Rec button. SCENE 6. Tap the Scene button that corresponds to the scene you're editing. This will overwrite the exited scene. NOTE: Be sure to select the same scene in steps 3 and 6, otherwise you may accidentally record over an exited scene Scanner Copy SCANNER This function allows you to copy the settings of one scanner to another. 1. Press and hold down the Scanner button you want to copy. 12

16 2. Operation Guide Scanner Copy SCANNER 2. While holding the Scanner button, tap the Scanner button you want to copy to Scene Copy 1. Program enable. 2. Tap the Bank Up/Down button to select the bank that contains the scene you wish to copy. BANK SCENE 3. Select the scene you want to copy by tapping its Scene button. 13

17 2. Operation Guide Scene Copy BANK 4. Tap the Bank Up/Down button to select the bank you wish to copy the scene to. 5. Tap the MIDI/Rec button. MIDI/Rec SCENE 6. Tap the Scene button you wish to copy the scene to. 14

18 2. Operation Guide Delete a Scene SCENE 1. Tap the desired Scene button to select the scene you wish to delete. Auto/Del SCENE 2. Press and hold down the Auto/Del button. While holding down the Auto/Del button, tap the Scene button that stores the scene you wish to delete. When a programmed scene is deleted, all DMX channel in this scene is set to Delete all Scenes This function will reset all DMX channel to 0 output. Program 1. With the power off, press and hold down the Program and Bank Down buttons at a time. BANK 2. Apply power again, all scenes should be cleared. 15

19 2. Operation Guide Bank Copy 1. Program enable. BANK 2. Tap the Bank Up/Down button to select the bank you wish to copy. 3. Tap the MIDI/Rec button. MIDI/Rec BANK 4. Tap the Bank Up/Down button to select the bank you wish to copy to. 16

20 2. Operation Guide Bank Copy Music/Bank Copy 5. Tap the Music/Bank Copy button, all LEDs and the Segment Display will flash three times briefly indicating the function has been completed. 6. Press the Program button for three seconds to exit Programming mode. 2.3 Programming Chase You must program scenes before you can program chases, this function allows you to store up to 240 scenes into one chase. 1. Program enable. Chase Button Tap the Chase button to select the chase to program. Each time you can select a chase only. 3. Select a desired scene from the bank that has stored scenes.(described in Programming Scenes) MIDI/Rec 4. Tap the MIDI/Rec button. 5. Repeat steps 3-4 until you've reached your desired effect. You may record up to 240 scenes into a chase. 17

21 2. Operation Guide Program a bank of scenes into a Chase 1. Program enable. 2. Select the chase using Chase buttons 1-6. Music/Bank Copy 3. Use Bank Up/Down button to select the bank that contains the scenes you wish to copy. 4. Tap the Music/Bank Copy button. MIDI/Rec Copy 5. Tap the MIDI/Rec Copy button, all LEDs and the Segment Display will flash three times briefly indicating all 8 scenes in this bank have been programmed into this chase Add a Step 1. Program enable. Blackout Step PROG Chase Scene Tap Sync/Display Step/time 8888 Bank Music trigger Auto trigger 2. Select the chase you wish to add a step to. 3. Tap the Tap Sync/Display button causing a highlight next to "Step", the first digit in the Segment Display shows the chase and the next three digits show its step. 18

22 2. Operation Guide Add a Step BANK 4. Tap the Bank Up/Down button to scroll to the step you wish to add a step after. MIDI/Rec 5. Tap the MIDI/Rec button, the Segment Display will read the step one higher than before. For example, if you want to insert a step between step 3 and step 4, and you scroll to step 3, when you tap the MIDI/Rec button, the Segment Display will read step 4. Blackout Step PROG Chase Scene Bank Tap Sync/Display Step/time 8888 Music trigger Auto trigger 6. Tap the Tap Sync/Display button again, the Segment Display shows the current chase, scene and bank. Create a desired scene and record it as a new step or select a programmed scene you wish to add into this chase. Hints: You may tap the Tap Sync/Display button to change the display mode between step and the bank. 19

23 2. Operation Guide Add a Step MIDI/Rec 7. Tap the MIDI/Rec button again, all LEDs and the Segment Display will flash three times briefly indicating the new step has been inserted into this chase Delete a Step 1. Program enable. Blackout Step PROG Tap Sync/Display Step/time 8888 Chase Scene Bank Music trigger Auto trigger 2. Select the chase that contains the step you wish to delete. 3. Tap the Tap Sync/Display button causing the Segment Display shows the steps. 4. Tap the Bank Up/Down button to scroll to the step you wish to delete. Auto/Del 5. Tap the Auto/Del button to delete the step, all LEDs and the Segment Display will flash three times briefly indicating that the step has been deleted. 20

24 2. Operation Guide Delete a Chase Chase Button Select the chase you wish to delete. Auto/Del Chase 2. Press and hold down the Auto/Del button. Tap the Chase button while holding down the Auto/Del button, all LEDs and the Segment Display will flash three times briefly indicating this chase has been deleted Delete all Chases Auto/Del 1. With the power off, press and hold down the Auto/Del and Bank Down buttons at the same time. BANK 2. Apply the power again. 21

25 2. Operation Guide 2.4 Running Scenes Manual Mode 1. When the power is turned on, this unit enters Manual mode automatically. 2. Make sure Auto trigger and Music trigger indicators in the Segment Display are both off. 3. Use the Bank Up/Down button to select the bank that contains the scenes you wish to run. SCENE 4. Tap the Scene button to select the scene to run Auto Mode This function allows you to run a bank of programmed scenes in a sequential loop. Auto/Del 1. Tap the Auto/Del button to activate Auto mode. A highlight next to "Auto trigger" will indicate Auto mode. 22

26 0 2. Operation Guide Auto Mode BANK 2. Use the Bank Up/Down button to select a bank of scenes to run. 0.1SEC 30S 3. After selecting the bank of scenes you wish to run, you can use the Speed slider(or Tap Sync/ Display button) and Fade Time slider to adjust the scenes to your desired effect. 10MIN SPEED FADE TIME Hints: The Tap Sync button is used to set the speed by tapping the button several times, the last two taps will define the speed with a maximum of 10 minutes. Tap Sync will override any previous setting of the Speed slider unless the slider is moved again. Auto/Del 4. Tap the Auto/Del button again to exit Auto mode. 23

27 2. Operation Guide Music Mode Music/Bank Copy 1. Tap the Music/Bank Copy button to activate Music mode. A highlight next to "Music trigger" indicates Music mode. BANK 2. Use the Bank Up/Down button to select the bank that holds the scenes you wish to run. The scenes you've selected will chase in a sequential order according to the music rhythms detected by the built-in microphone. Music/Bank Copy 3. Tap the Music/Bank Copy button again to exit Music mode. 24

28 2. Operation Guide 2.5 Running Chases You must program scenes before you can run chases Manual Mode 1. When the power is turned on, this unit enters Manual mode automatically. 2. Select your desired chase by tapping one of the six Chase buttons. A second tap of this button will deactivate this function. 3. Use the Speed slider(or Tap Sync button) and Fade Time slider to adjust the current scenes to your desired effects. BANK 4. Use the Bank Up/Down button to scroll through the chase to run all banks of scenes Auto Mode Auto/Del 1. Tap the Auto/Del button to activate Auto mode. A highlight next to "Auto trigger" will indicate Auto mode. 25

29 2. Operation Guide Auto Mode Chase buttons Select your desired chase by tapping one of the six Chase buttons. A second tap of this button will deactivate this function. 0.1SEC 30S 3. Use the Speed slider(or Tap Sync) and Fade Time slider to adjust the chase to your desired effects. 10MIN SPEED FADE TIME 0 You may select several chases at a time, the chases will run in sequence that you select the chases Music Mode Music/Bank Copy 1. Tap the Music/Bank Copy button to activate Music mode. A highlight in the Segment Display next to "Music trigger" will indicate Music mode. 26

30 2. Operation Guide Music Mode Chase buttons Select your desired chase by tapping one of the six Chase buttons, the chase will be triggered by the music rhythms. You may select several chases at a time. 2.6 MIDI Operation MIDI Channel Setting MIDI/Rec 1. Press and hold down the MIDI/Rec button for three seconds, the last two digits of the Segment Display will flash to indicate MIDI channel setting is ready. BANK 2. Use the Bank Up/Down button to select the DMX channel to assign to MIDI channel. 27

31 2. Operation Guide MIDI Channel Setting MIDI/Rec 3. Press and hold down the MIDI/Rec button for three seconds to store your setting and to deactivate MIDI setting. If you wish to give up your setting, tap any other button(except Bank Up/Down buttons) to exit MIDI mode Implementation This unit receives Note signals, which enables to run 15 banks(01-15) of scenes and 6 chases of scenes. In addition, blackout function can be activated by MIDI signal. BANK NOTE NUMBER FUNCTION Bank 1 00 to 07 Turn on or off Scenes 1-8 of Bank 1 Bank 2 08 to 15 Turn on or off Scenes 1-8 of Bank 2 Bank 3 16 to 23 Turn on or off Scenes 1-8 of Bank Bank 14 Bank 15 Chase 1 Chase 2 Chase 3 Chase 4 Chase 5 Chase to to Turn on or off Scenes 1-8 of Bank 14 Turn on or off Scenes 1-8 of Bank 15 Turn on or off Chase 1 Turn on or off Chase 2 Turn on or off Chase 3 Turn on or off Chase 4 Turn on or off Chase 5 Turn on or off Chase Blackout 28

32 Technical Specifications Power Input... DC 9~12V, 300 ma min. DMX Output... 3 pin female XLR MIDI Signal... 5 pin standard interface Audio Input... By built-in microphone Dimensions x132x73mm Weight(appro.) kg 29

33

34

35

36 Rev 1.0 January 2004 All Rights Reserved

37

38

39

40

41

42