INFRARED REMOTE CONTROL HELICOPTER

Transcription

1 3 CHANNEL GYROSCOPIC STABILIZATION TECHNOLOGY FOR SMOOTH HANDLING INFRARED REMOTE CONTROL HELICOPTER Please read these instructions carefully before using the helicopter

2 Safety Instructions 1. Please keep the helicopter and the box away from small children. 2. Please keep a safe distance from high speed rotating propellers to avoid injury. 3. First time users should be gentle with the throttle to avoid crashing the helicopter or any potential injuries. 4. When finished flying, please turn off first the remote controller then the helicopter. 5. Please keep the charging battery away from fire and humidity. 6. Do not fly the helicopter near pets, young children, elderly and disabled people. 7. Non rechargeable batteries are not to be charged; Different types of batteries or new and used batteries are not to be mixed; Batteries are to be inserted with correct polarity; Exhausted batteries are to be removed from the product. The supply terminals are not to be short circuited 8. When not in use, please turn off the power of controller and helicopter. When the helicopter is not in use for a long period of time, remove the batteries from remote controller. Ready to fly 1. Use a place away from any people, pets and obstacles. 2. Turn helicopter power switch ON. The helicopter lights will flash. It will search the signal from controller. 3. Turn the remote controller ON. The indicator light will flash. Push the left control throttle up and down. The indicator light will be constant. 4. Push the left control throttle up slowly and start to fly. Low power protection When the helicopter s battery is low, the system will cut-off the power to avoid excessive discharge. This will reduce any damage to the battery. Instructions for care and maintenance 1. Please clean the helicopter and controller with a clean soft cloth. 2. Store the helicopter in a dry, clean place. Keep the box for storage. 3. Inspect the helicopter before use. Do not use if any parts are damaged or broken.

3 Battery Installation & Charging Battery Installation in the remote controller 1. Use a crosshead screw driver to remove the controller battery cover. Insert 4 batteries (size AA, 1.5V) observing the correct polarity indicated in the compartment. Replace the battery cover and secure the screw. Different types of batteries or new and used batteries are not to be mixed; Batteries are to be inserted with correct polarity; Exhausted batteries are to be removed from the product; The supply terminals are not to be short circuited. Charging the helicopter battery A. To charge the helicopter with remote Control B.To charge the helicopter with USB (Connected to computer) 1. Be sure to switch off the helicopter power. 2. Charging by A: Plug the provided USB charging cable into the helicopter, then insert the USB plug into the remote controller charge port. The USB indicator should turn on when the battery starts charging. The USB indicator will turn off when the battery is fully charged (About minutes). Charge by B: Plug the provided USB charging cable into the helicopter, then insert the USB plug into your computer. The USB indicator should turn on when the battery starts charging. The USB indicator will turn off when the battery is fully charged (About minutes). Charge time: minutes Fly time 5-6 minutes! The helicopter contains a built-in Li-Po battery, please pay attention to the following matters: - Keep the battery away from fire and heating sources. It could damage the battery or cause it to explode. - Keep the helicopter and the battery away from water. - Only charge the helicopter with the provided adapter. - Do not remove or dismantle the built-in battery. - Do not leave unattended when charging.

4 To reset calibration, press both buttons for 2 seconds. The RC power indicator will flash 3 times to confirm the action.

5 Troubleshooting 2.Change frequency or use the helicopter out of the range of other RC helicopters. Spare parts All the spare parts below can be bought from local distributor. S107N-01A Head cover A S107N-01B Head cover B S107N-03B Tail blade S107N-04 Main shaft S107N-07 Gear S107N-12B Tail support pipes S107N-02A S107N-02B S107N-03A Tail decorations A Tail decorations B Main blades S107N-05A Balance bar S107N-05B Connect buckle S107N-08 S107N-09 S107N-11 Blade connector Main shaft connector Tail motor sets S107N-13A Motor A S107N-16 S107N-17 USB charge wire Remote controller S107N-13B Motor B S107N-14 Battery S107N-06 Landing gear S107N-12A Main frame metal parts S107N-15 Circuit board

6

7

8