North Texas FLL Coaches' Clinics. Beginning Programming October Patrick R. Michaud republicofpi.org

Transcription

1 North Texas FLL Coaches' Clinics Beginning Programming October 2014 Patrick R. Michaud republicofpi.org

2 Goals Learn basics of Mindstorms programming Be able to accomplish some missions Provide tips that have helped our team Point out traps that cause frustration

3 Topics EV3 programming environment Programming basics Motor blocks moving forward and backward Detecting lines, borders, colors Port view and view mode Turning basics Turns using gyro sensor Simple My Blocks

4 EV3 Programming Environment Project Zoom Open programs Start Block Download Palletes Action Flow Sensor Data Advanced My Blocks Control Port View Download and run Program Blocks

5 Programming basics A program is a sequence of actions to perform Start Move forward 3 Play sound Move backward 3 Each action is represented by a block Icons indicate the type and values of block Robot does exactly what you tell it to do and only what you tell it to do Programmer determines what actions to perform

6 Motor blocks moving the robot Motor Ports Move Tank Block On for Rotations Power Left Power Right Rotations Brake at end Motor ports: which motors to turn Power left/right: how fast to turn each motor Rotations: how far to turn each motor Brake at end: whether to apply brakes when done

7 Motor blocks Motor commands Types of moves Move tank left/right motor speeds Move steering turn direction / sharpness Large motor (one) motor speed

8 Wait blocks Program executes blocks in sequence Wait blocks makes program wait for something to happen before continuing to next block Wait for seconds Wait for sensor to read a certain value Wait for sensor to change Example: Start motors on wait 3 sec motors off

9 Wait block options

10 Touch and color sensors Touch sensor detects pressure Color sensor can detect selected colors Sensor should be 0.5 to 2.0 cm from color to be detected

11 Moving to a border, line, or color Move until touch sensor pressed Start motors on wait for motors off touch press Move until black, green, or red detected Start motors on wait for motors off black, green or red

12 Use port view to see sensor changes Software view: Motor A Motor B -16 degrees 28 degrees Touch 1 not pressed Motor C 51 degrees Gyro 2 Color sensor degrees 4 (yellow) EV3 view:

13 Turning basics types of turns Point turn Pivot turn Wide turn Wheels move in opposite directions One wheel moves, other wheel brakes One wheel moves slower than other we use this, most consistent

14 Fundamentals of turns The robot turns when driving wheels move at different speeds The robot turns towards the slower wheel The greater the difference in speeds, the tighter the turn

15 Fundamentals of turns Quiz: If a wheel turns 90 degrees, does the robot turn 90 degrees? Answer: No There is a formula to convert wheel turn angles to robot turn angles (advanced programming) But many teams just use trial and error Or, use a gyro sensor

16 Gyro sensor Gyro sensor detects rotation about an axis Can measure rotation rate or rotation angle Sensor has bias and drift sometimes shows movement even when still

17 Reducing gyro drift The following block sequence recalibrates the gyro sensor to eliminate drift: Measure Angle and Rate Wait 0.5 sec Gyro sensor Compare Angle equal to 0 Perform this once at beginning of program Requires 2-3 seconds to complete Gyro must be stationary while calibrating Trap: Gyro reset block doesn't recalibrate gyro!

18 Turns using gyro sensor Once gyro reads correctly, turning an angle is: turn on one motor wait for gyro to change 60 Gyro Change Angle turn off motors # of degrees to change Gyro sensor is not precise Robot may turn slightly more or less than 60

19 Simple My Blocks - turning A program to move, turn, then move: move fwd 3 rot turn robot 60 to left move fwd 1.5 rot Adding three blocks for every turn will get tedious We can create custom blocks called My Blocks

20 Creating a My Block Start by drag-selecting the blocks to be used Select My Block Builder from the Tools menu

21 Creating a My Block Give the My Block a name Click the + to add a parameter Click Parameter Setup Name parameter Power Give it a default of 50

22 Creating a My Block Click + again to create another Parameter Name it degrees Default value 0 You can change the parameter icons to be more meaningful Click Finish

23 Creating a My Block A new program is created for the My Block The grey block on the left has our parameter inputs for power and degrees We have to wire them to the appropriate blocks

24 Creating a My Block Drag a wire from the Power parameter to the C motor power input Drag a wire from the Degrees parameter to the degrees input of the wait block

25 Creating a My Block We now have a My Block for turns Our original program has the three-block sequence replaced with our turn block move fwd 3 rot turn robot 60 to left move fwd 1.5 rot Our turn block appears in the My Blocks palette

26 My Blocks Easier to read and build program Suggestions: Create a My Block for each mission Combine mission My Blocks into trip My Blocks Create standard My Blocks for Moving forward and backward, turning Stopping Motorized attachments Initialization

27 Stop stop stop Trap: Be sure the robot comes to a full stop between moves When Move blocks complete, they brake the motors Inertia carries the robot further, so the motors have to back up a bit This takes a little time If your program immediately goes to next action, robot will be inconsistent

28 Create a stop My Block Add a short wait after every movement A simple stop My Block: Can use this whenever you want to be sure the robot is stopped:

29 Thank you! Questions? Patrick R. Michaud republicofpi.org Join the NorthTexasFLL group!