Connecting a Personal Computer or Laptop to RezNet
|
|
- Kathlyn Davidson
- 8 years ago
- Views:
Transcription
1 Connecting a Personal Computer or Laptop to RezNet Preamble: Humber has outfitted each suite in Residence with an Ethernet connection. Should you wish to access Internet resources, you may do so by following the setup procedure outlined in this document. Please contact the Technical Service Desk if you encounter problems or require assistance. Step 1: Connect Your Computer Your computer needs two important components to connect to RezNet: a Network Interface Card (NIC) to send and receive data and a Category 5 Ethernet Cable to carry the data to and from your computer. 8 contacts -4 contacts Locate the network jack in your room. Plug one end of your Ethernet cable into the jack. You should hear a click when you insert the connector. Continue by locating the network port on the back of your computer. Plug the other end of the Ethernet cable into the network port.
2 Listen for the click. Turn on your computer. If you did everything correctly, a light will start flashing near the computer s network port. ATTENTION: Do not plug your computer into another guest s jack or allow guests to plug into your jack. Do so and the switch will terminate the connection. Open access jacks are available in the Common and Study rooms. Contact the Technical Service Desk for assistance. Important: A modem is not the same as a Network Interface Card and a telephone cable is not the same as an Ethernet cable. You must use the right hardware! Network cables are available for sale in the Bookstore. Step : Configure Your Operating System After you plug your computer into the data network, you may need to reconfigure your operating system. The procedure you need to follow depends entirely on the operating system you have running. Windows Vista Users...Go to Appendix A Windows XP Users...Go to Appendix B Windows 000 Users...Go to Appendix C Windows 9X/ME Users... Go to Appendix D Mac OS X Users...Go to Appendix E Do not forget to reboot your computer after applying new network settings. Step 3: Test Your Connection Once you have your computer/laptop connected and your operating system configured, you are more-or-less ready to go. Launch an instance of Internet Explorer and try surfing the Web. If you do not have network access, check your Network Interface Card (NIC) for a link light (Step #1) and double-check your operating system settings (Step #). If you still cannot connect, contact the Technical Service Desk for assistance. Step 4: Install Anti-virus Software It is critically important you run up-to-date virus detecting software. Should your computer become infected or cause problems, the Technical Page of 1
3 Service Desk will forcibly terminate your connection at the switch until you can prove you have taken corrective action. Depending on the nature of the infection, there may be other repercussions. If you do not have an antivirus program, or if you are unhappy with the antivirus program you presently own, you are in luck because Humber is reselling PC-cillin through the Bookstore for $10. Go to the Bookstore and ask for an Antivirus Voucher. Redeem the voucher at the Media Centre and you are good to download, install, and run the program. You may also want to consider installing software to detect and remove Spyware. Spyware are programs designed to track your computing activity and report back to commercial agencies. Someone may be looking at your personal information right now. Go to the Information Technology Services site and look for a free Spybot download. Note: Tip sheets for installing, using, and configuring PC-cillin and Spybot are available on the Information Technology Services site. Developed by the Technical Service Desk Last Revised on Monday, August 18, 008 Page 3 of 1
4 Appendix A - Windows Vista Configuration Step 1: Click the Start button and click on the Control Panel shortcut. Step : Click on Classic View to reveal all customizable objects. Step 3: Double-click on the Network and Sharing Centre shortcut. Step 4: Click on Manage Network Connections in the left-hand pane. Page 4 of 1
5 Step 5: Locate the Local Area Connection shortcut. Right-click said shortcut and select the Properties item. Step 6: Select the Internet Protocol Version 4 (TCP/IPv4) item in the list. Then, click the Properties button. 1 3 Step 7: Select the Obtain an IP Address Automatically and Obtain DNS Server Address Automatically options. Click OK. Step 8: Click the OK button to close the Local Area Connection Properties dialog box and reboot your computer. Page 5 of 1
6 Appendix B - Windows XP Configuration Note: Do not have this icon? Click the Start button, point to Settings, and click Control Panel. Then, double-click on Network Connections. Step 1: Right-click on My Network Places and select the Properties option. Step : Double-click on the Local Area Connection icon. 1 Step 3: Click on Properties in the Local Area Connection Status window. Step 4: Select the Internet Protocol (TCP/IP) item and click Properties. Page 6 of 1
7 1 Step 5: Click on the Obtain an IP Address Automatically option. Step 6: Select the Obtain DNS Server Address Automatically option. Click OK. Step 7: Click the Close button and then reboot your computer/laptop. Page 7 of 1
8 Appendix C - Windows 000 Configuration Step 1: Right-click on My Network Places and select the Properties item. Step : Double-click the Local Area Connection shortcut. 1 Step 3: Click on Properties in the Local Area Connection Status window. Step 4: Select the Internet Protocol (TCP/IP) item and click Properties. Page 8 of 1
9 1 Step 5: Click on the Obtain an IP Address Automatically option. Step 6: Select the Obtain DNS Server Address Automatically option. Click OK. Step 7: Click the Close button and then reboot your computer/laptop. Page 9 of 1
10 Appendix D - Windows 9X/ME 1 1 Step 1: Open the Control Panel and double-click the Network icon. Select the TCP/IP option and click on Properties. Step : Click on the IP Address tab. Select the Obtain an IP Address Automatically option and click OK. Step 3: Continue by clicking on the WINS Configuration tap and clicking on the Disable WINS Resolution option. Step 4: Continue by clicking on the DNS Configuration tab in the same dialog box. Click on the Disable DNS option. Page 10 of 1
11 3 Step 5: Click the Gateway tab. Use the Remove button to delete everything from the Installed Gateways box. Click OK. Page 11 of 1
12 Appendix E - Mac OS X Users 1 Step 1: Open the System Preferences window. Double-click the Network icon in the Internet & Network section. Step : Select the Built-in Ethernet option. Then, select Using DHCP in the Configure box of the TCP/IP tab. Step 3: Click the Apply Now box and reboot your computer/laptop. Page 1 of 1
Internet Guide. Prepared for 55 John Street
Internet Guide Prepared for 55 John Street I. Internet Service How do I connect to the Internet? WiFi (Wireless Connectivity) is available throughout the building. In order to connect, you will need a
More informationACT High Speed WiMAX Internet
ACT High Speed WiMAX Internet Internet Configuration Manual This manual walks you through the steps of configuring your computer for High Speed WiMAX Internet service with Windows 7, Vista, XP, 2000, And
More informationInternet for Everyone In-Room Instructions January 2011 Version 1.3
Internet for Everyone In-Room Instructions January 2011 Version 1.3 Everywhere Internet 2006 Page 1 of 17 Connecting your computer to the Everywhere Internet network in your room 1. You need a network
More informationHYPERLINK Internet PC setup guide. HYPERLINK Internet support helpdesk at 1-866-302-5525.
HYPERLINK Internet support helpdesk at 1-866-302-5525. Congratulations on your new residence and welcome to HYPERLINK Internet service. In a few short moments you will be connected to one of the fastest
More informationNF5 VOIP Setup Guide (for Generic)
NF5 VOIP Setup Guide (for Generic) Configuring your NF5 for VOIP Service The following steps will take you through the process of setting up your VOIP connection. Step 1: Checking Computer Network Settings:
More informationTurn off all of your network devices, including your computer, Modem and the Router.
Note The product model shown in this part is TL-R460, as an example. Turn off all of your network devices, including your computer, Modem and the Router. Connect the WAN port on your Router to the Modem
More informationActiontec GT784WN Router
Table of Contents General Information...1 Verify Computer Settings...1 Router Installation...3 Configuring Your Router...3 Configuring Your Computer...7 Configuring Your Email...9 General Information Router
More informationNF1Adv VOIP Setup Guide (for Pennytel)
NF1Adv VOIP Setup Guide (for Pennytel) Configuring your NF1Adv for VOIP Service The following steps will take you through the process of setting up your VOIP connection. Step 1: Checking Computer Network
More informationPlease use only wired network connections to configure the router.
Note Please use only wired network connections to configure the router. Connect the WAN port on your Router to the Modem s LAN port with an Ethernet cable. Note If connecting the TL-WR543G to the WISP
More informationNF3ADV VoIP Setup Guide (for TPG)
NF3ADV VoIP Setup Guide (for TPG) Configuring your NF3ADV for TPG VoIP The following steps will take you through the process of setting up your VoIP connection. This guide assumes that the NF3ADV already
More informationNF1Adv VOIP Setup Guide (for Generic VoIP Setup)
NF1Adv VOIP Setup Guide (for Generic VoIP Setup) Configuring your NF1Adv for VOIP Service The following steps will take you through the process of setting up your VOIP connection. Step 1: Checking Computer
More informationTurn off all of your network devices, including your computer, Modem and the Router.
Note Please use only wired network connections to configure the Router. Turn off all of your network devices, including your computer, Modem and the Router. Connect the WAN port on your Router to the Modem
More informationPlease use only wired network connections to configure the Router.
Note Please use only wired network connections to configure the Router. Power down all of your network devices, including your computer(s) and the Modem Router. If you currently use a modem, disconnect
More informationIf no telephone is needed, please connect the LINE port of the Modem Router to the wall jack using the telephone line directly.
Note Please use only wired network connections to configure the Router. Power down all of your network devices, including your computer(s) and the Modem Router. If you currently use a modem, disconnect
More informationTable of Contents. 0. Internet Connectivity Assumptions..2. 0. Identifying the Network Wall Jack... 2. 0. Identifying the Ethernet Cable..
Table of Contents 0. Internet Connectivity Assumptions..2 0. Identifying the Network Wall Jack... 2 0. Identifying the Ethernet Cable..4 0. Identifying the Network Interface Card...5 0. Connecting Your
More informationInstallation. If you currently use a modem, disconnect it now - the Modem Router will replace your current modem.
Installation Note Please use only wired network connections to configure the Modem Router. If you currently use a modem, disconnect it now - the Modem Router will replace your current modem. Connect your
More informationOmni 56K USB Lite Quick Start Guide
Omni 56K USB Lite Quick Start Guide ZyXEL TOTAL INTERNET ACCESS SOLUTION 1. Hardware Installation Connect your modem to your analog phone or fax. Use the phone cord included to connect to the phone jack
More informationInstallation. Note Please use only wired network connections to configure the router.
Installation Note Please use only wired network connections to configure the router. Power down all your network devices, including your computer(s) and the Modem Router. If you currently use a modem,
More informationNote The product model shown in this QIG is TD-8817, as an example.
Note The product model shown in this QIG is TD-8817, as an example. Turn off all of your network devices, including your computer and the Modem Router. If you currently use a modem, disconnect it now -
More informationMetasys System Direct Connection and Dial-Up Connection Application Note
Metasys System Direct Connection and Dial-Up Connection Application Note Code No. LIT-1201639 Software Release 5.1 Issued August 27, 2013 Supersedes October 4 2010 Refer to the QuickLIT website for the
More information64-Bit Compatibility with Micromeritics Applications
Tech Tip 7 64-Bit Compatibility with Micromeritics Applications Micromeritics products are designed to operate in most Microsoft Windows environments. However, more current versions of Microsoft Windows,
More information4-441-095-12 (1) Network Camera
4-441-095-12 (1) Network Camera SNC easy IP setup Guide Software Version 1.0 Before operating the unit, please read this manual thoroughly and retain it for future reference. 2012 Sony Corporation Table
More informationInstallation. The product model shown in this QIG is TD-W8951ND, as an example.
Installation Note The product model shown in this QIG is TD-W8951ND, as an example. Note Please use only wired network connections to configure the Router. Before cable connection, keep your hands dry.
More informationQuick Installation Guide DAP-1360. Wireless N 300 Access Point & Router
DAP-1360 Wireless N 300 Access Point & Router BEFORE YOU BEGIN Delivery Package Access point DAP-1360 Power adapter DC 12V Ethernet cable (CAT 5E) (brochure). If any of the items are missing, please contact
More informationAcqKnowledge 3.7.3 or better for Windows OS (version compatibility varies each release)
APPLICATION NOTES 42 Aero Camino, Goleta, CA 93117 Tel (805) 685-0066 Fax (805) 685-0067 info@biopac.com www.biopac.com 09.10.2007 Application Note 209: AcqKnowledge for Windows: Upgrade for 1+MP150s and
More informationModel:BL-WDR3750 750Mbps Wireless Dual Band 11AC Router
Quick Installation Guide Model:BL-WDR3750 750Mbps Wireless Dual Band 11AC Router 1.Connecting the device Note: Please use wired network connections only to configure the Router. 1 Connect the WAN port
More informationDSL Self-install Kit Instructions. SpeedStream 4100
DSL Self-install Kit Instructions SpeedStream 4100 Cover and installation notes Page 1 1. Verify your system requirements Page 2 2. Verify the contents of your DSL Self-Install kit Page 2 3. Install filters
More informationInstallation Guide. EarthLink
Installation Guide EarthLink Welcome to EarthLink DSL & Home Phone Service Congratulations! You ve made the smart choice for super-fast DSL and super-simple phone service. Follow the instructions in this
More informationEnabling Internet Connection Sharing on Windows 2000 15. Enabling ICS On Windows XP As The Host 4 Enabling ICS On Windows XP As The Client 11
Sharing an Internet Connection with SatDirect Plus Table of Contents Contents Section 1: Section 2: Section 3: Introduction... 1 Physical Setup......2 Enabling Internet Connection Sharing on Windows XP
More information1. Hardware Installation
4 Port 10/100M Internet Broadband Router with USB Printer server Quick Installation Guide #4824904AXZZ0 1. Hardware Installation A. System Requirement Before you getting started, make sure that you meet
More informationUBIQUITI BRIDGE CONFIGURATION PROCEDURE (PowerStation & NanoStation Units ONLY)
UBIQUITI BRIDGE CONFIGURATION PROCEDURE (PowerStation & NanoStation Units ONLY) Hardware Installation 1. Initial placement for programming and configuration purposes should be performed in an indoor environment.
More informationDeploying Windows Streaming Media Servers NLB Cluster and metasan
Deploying Windows Streaming Media Servers NLB Cluster and metasan Introduction...................................................... 2 Objectives.......................................................
More informationThis manual will help you connect your Microsoft Windows XP, Vista, or 7, or Apple OS X computer to the University of Maryland campus data network.
This manual will help you connect your Microsoft Windows XP, Vista, or 7, or Apple OS X computer to the University of Maryland campus data network. Prerequisites for Network Registration: 1. In order to
More information# of Days Fee Total Cost Including GST 1 7 days $20 $21.40 8 14 days $40 $42.80 15 21 days $60 $64.20 22+ days $75 $80.25
Welcome to RezNet! What is RezNet? RezNet is a High Speed Internet Service we provide here at Western. As a visitor to one of Western s residences during the summer of 2003, you can receive this high speed
More informationAdditional Requirements for ARES-G2 / RSA-G2. One Ethernet 10 Base T/100 Base TX network card required for communication with the instrument.
TA Instruments TRIOS Software Installation Instructions Installation Requirements Your TRIOS Instrument Control software includes all the components necessary to install or update the TRIOS software, as
More informationEthernet Radio Configuration Guide
Ethernet Radio Configuration Guide for Gateway, Endpoint, and Repeater Radio Units April 20, 2015 Customer Service 1-866-294-5847 Baseline Inc. www.baselinesystems.com Phone 208-323-1634 FAX 208-323-1834
More informationLMi.net DSL Modem Self-Install Guide
LMi.net DSL Modem Self-Install Guide Welcome to LMi.net! Here are the steps to complete your DSL installation. If you need any help with any of these steps call our Tech Support line at 510-843-6389 x300
More informationChapter 2 Preparing Your Network
Chapter 2 Preparing Your Network This document describes how to prepare your network to connect to the Internet through a router and how to verify the readiness of your broadband Internet service from
More informationNetwork Setup Guide. Introduction. Setting up for use over LAN
Network Setup Guide This manual contains the setup information required to use the machine over wired LAN. If you use the machine with USB connection, refer to your setup sheet. Introduction To use the
More informationRAPID BROADBAND INSTALLATION RAPID BROADBAND SUPPORT CONTACT DETAILS. support@rapidbroadband.ie AND TROUBLESHOOTING GUIDE. Email: Tel: 076 6708787
RAPID BROADBAND INSTALLATION AND TROUBLESHOOTING GUIDE RAPID BROADBAND SUPPORT CONTACT DETAILS Email: support@rapidbroadband.ie Tel: 076 6708787 January 2008 1 INTERNET CONNECTION TROUBLESHOOTING GUIDE
More informationUsing a simple crossover RJ45 cable, you can directly connect your Dexter to any computer.
Dexter is a network device using the Ethernet protocol to connect and communicate with other devices on the network: Computers, routers, DHCP servers. Thus you have to setup your Dexter and your network
More informationEnGenius ERB9250 300M Range Extender. Quick Start Guide
EnGenius ERB9250 300M Range Extender Quick Start Guide Package Contents One ERB9250 300M Range Extender One 12V/1A power adapter Two 2dBi 2.4GHz SMA antennas One Ethernet cable One CD-ROM with user s manual
More informationStep 1: Checking Computer Network Settings:
Configuring your 3G18WV for VOIP The following steps will take you through the process of setting up your VOIP connection. Step 1: Checking Computer Network Settings: You will need to connect your computer
More informationAcqKnowledge for Windows: Upgrade for 1+MP150s and Domain Network Access or Direct Communication Setup (Domain/Non-domain)
APPLICATION NOTES 42 Aero Camino, Goleta, CA 93117 Tel (805) 685-0066 Fax (805) 685-0067 info@biopac.com www.biopac.com 09.10.2007 Application Note 208: AcqKnowledge for Windows: Upgrade for 1+MP150s and
More informationPoint to Point Broadband Internet Service Business
Point to Point Broadband Internet Service Business [Type the company name] USER GUIDE VERSION 1.012010 [Type the document subtitle] Table of Contents Welcome to Point to Point Broadband!... 2 Disclaimer.
More informationPrestige 314 Read Me First
Prestige 314 Read Me First Console WAN 10M PORT Prestige Rear Panel Connections CONNECTION Use an RS-232 console cable. Use the cable that came with your broadband modem. LAN 10/100M Port Number COMPUTER
More informationBroadband DSL Quick Start Set Up Guide
Broadband DSL Quick Start Set Up Guide Index What s in the box?... 1 Applying the DSL filters... 2 What devices must be filtered... 3 Connecting the DSL modem... 3-5 Connecting a computer... 5 Setting
More informationPalomar College Dial-up Remote Access
Palomar College Dial-up Remote Access Instructions for Windows 95/98 and Windows 2000 Following are instructions to implement dialup access to the Palomar College network, email and Internet. The minimum
More informationMaxSea TimeZero NN3D Radar Connection Checklist
MaxSea TimeZero NN3D Radar Connection Checklist This TechNote only applies to MaxSea TimeZero Explorer. Description Follow this TechNote if you have any of these symptoms: - The Radar Tab (Radar WorkSpace)
More informationInstallation. The product model shown in this QIG is TD-W8961ND, as an example.
Installation The product model shown in this QIG is TD-W8961ND, as an example. Please use only wired network connections to configure the router. Power down all your network devices, including your computer(s)
More informationHigh-Speed Broadband Internet Guide
High-Speed Broadband Internet Guide Welcome Welcome to SkyBest High-Speed Broadband Internet. SkyBest High-Speed Broadband Internet allows for rapid downloading of large files, such as music and graphics.
More informationHigh Speed Internet, Welcome Kit. If your apartment is served by Ethernet: How do I connect to the network if not using a router?:
High Speed Internet, Welcome Kit We provide a WIRED High Speed Internet connection to your apartment. Your apartment will be served by a DSL modem or Ethernet jack. If you have multiple users in your apartment
More informationApple Mac. AT&T DSL Internet Service Implementation Planner Apple Mac PC Configuration Guide Version 1.2 Page 1
Apple Mac Page 1 Apple Mac Setup Welcome to AT&T DSL Internet Service! This guide is designed to help you configure your Mac to access the Internet quickly and easily using AT&T DSL. Before You Begin First,
More informationHigh-Speed Broadband Internet Guide
High-Speed Broadband Internet Guide Welcome Welcome to SkyBest High-Speed Broadband Internet. SkyBest High-Speed Broadband Internet allows for rapid downloading of large files, such as music and graphics.
More informationPrestige 650R-31/33 Read Me First
Prestige 650R-31/33 Read Me First Prestige Rear Panel Connections PORT DSL CONSOLE LAN 10/100M POWER Connect to a telephone jack using a telephone wire. CONNECTION Connect to a serial port (COM port) on
More informationPrestige 660R-6x Read Me First
Prestige 660R-6x Read Me First Prestige Rear Panel Connections DSL PORT CONNECTION Connect the DSL port on the Prestige to the wall jack using the included DSL cable (telephone wire). Connect the micro
More informationFrontier DSL SelfConnect Guide
Frontier DSL SelfConnect Guide Frontier DSL Self-Installation Guide Table of Contents Getting Started...2 Customer and Computer Requirements...2...3 STEP 1: Install Microfilters...3 STEP 2: Install Your
More informationDial Up Config & Connecting Instructions with Graphics
Dial Up Config & Connecting Instructions with Graphics Dial Up Config & Connecting Below are the Basic Manual Configurations Connecting to the Internet for the following operating systems: Windows 2000
More informationTELUS Internet set up guide. Read me first
TELUS Internet set up guide Read me first Welcome Thank you for choosing TELUS. The 8 simple steps in this guide will help you set up your wireless gateway and quickly connect to the Internet. If you have
More informationHow to make a VPN connection to our servers from Windows XP
How to make a VPN connection to our servers from Windows XP Windows XP can only make a Point-To-Point Tunneling Protocol (PPTP) type of VPN connection to our servers. This requires TCP Port 1723 to be
More informationIf you need additional assistance please contact our Technical Support Center at 24 hours a day, 7 days a week.
Cisco SPA 2100 Phone Adapter Installation Manual Index Installation of the Cisco SPA 2100 Phone Adapter to NationPhone P. 1 Index, before you begin, and what is included P.2 Installing the NationPhone
More informationDSL Self-install Kit Instructions. SpeedStream 5360
DSL Self-install Kit Instructions SpeedStream 5360 Cover and installation notes Page 1 1. Verify your system requirements Page 2 2. Verify the contents of your DSL Self-Install kit Page 2 3. Install filters
More informationQuick Installation Guide DSL-2750U/NRU. 3G/ADSL/Ethernet Router with Wi-Fi and Built-in Switch
DSL-2750U/NRU 3G/ADSL/Ethernet Router with Wi-Fi and Built-in Switch BEFORE YOU BEGIN Delivery Package Router DSL-2750U/NRU Power adapter RJ-11 telephone cable Straight-through Ethernet cable (CAT 5E)
More informationDefiance College Networking Handbook
Defiance College Networking Handbook Installation Instructions and Reference Manual for Campus Network Connections including Residence Halls and Wireless Access Points Revision 20141203 Preface All residence
More informationTRENDnet. <a href="mailto:webmaster@ trendnet.com"> www.trendnet.com. Quick Installation Guide. Product Warranty Registration
Quick Installation Guide Product Warranty Registration website at http://www.trendnet.com www.trendnet.com Please take a moment to register your product online.
More informationQuick Installation Guide DSL-2750U. 3G/ADSL/Ethernet Router with Wi-Fi and Built-in Switch
DSL-2750U 3G/ADSL/Ethernet Router with Wi-Fi and Built-in Switch BEFORE YOU BEGIN Delivery Package Router DSL-2750U Power adapter DC 12V/1A RJ-11 telephone cable Ethernet cable (CAT 5E) Splitter (brochure).
More informationSelf Help Guide IMPORTANT! Configuring Your Router With Your Modem. Please read the following carefully; This Guide refers to the following Products:
IMPORTANT! This Guide refers to the following Products: Configuring Your Router With Your Modem Please read the following carefully; Synopsis: A standard (Wireless) Router does not come equipped with the
More informationYou may refer the Quick Installation Guide in the package box for more information.
Hardware Installation: 1. Turn off your modem. 2. Use one Ethernet cable to connect your modem to WAN port (Blue) port of BR-6228nC. 3. Use another Ethernet cable to connect your PC to one LAN Port (Yellow)
More informationThe range of Wi-Fi coverage and usage. Hub Computers which can
300Mbps Wireless LAN Repeater Quick Start Guide Version:MZK-EX300N_QIG-A_V1.1 In order to guarantee the correct usage of our products, this guide gives instructions on how to set and use our products.
More informationWhat is a Home Network? A home network is a collection of two or more home computers connected together through a wired or wireless connection.
Building A Home Network What is a Home Network? A home network is a collection of two or more home computers connected together through a wired or wireless connection. Why should I network my computers
More informationFirst of all Let's look at how you would connect your laptop via Ethernet, as it is the easier of the two methods.
How to get a Internet Connection on your laptop This guide will help you to get an internet connection on your laptop either via Wi-Fi (e.g. in a café or hotel) or via Ethernet (the RJ45 type connector
More informationIf you never used nor intend to use the wired-connection, then please disregard the following info.
Version date: 21/04/2015 Dear library users, In the library you can connect to the internet in two ways, using wireless or a wired-connection. The wired-connection is faster, allows you to connect to the
More informationSelf Help Guide. Please read the following carefully; Synopsis: Requirements: A Computer with a working RJ45 LAN Port All Belkin Modem Routers
IMPORTANT! This Guide refers to the following Products: Establishing A Connection From PC To Router Please read the following carefully; Synopsis: This Self-Help Guide is designed to assist you if you
More informationTurn on all of your network devices and then check to see if the LEDs on the Access Point display normally as the diagram below describes.
Connect to the Access Point with the Ethernet cable or via wireless. The default SSID of the Access Point is TP-LINK_ XXXXXX. The XXXXXX is the last 6 characters of the Access Point s MAC address. Plug
More informationDSL Installation Guide
DSL Installation Guide Thank you for choosing Integra Telecom s DSL service! Introduction This guide will walk you through the DSL installation process and will help you configure a computer to access
More informationAssign a static IP address 192.168.1.100 for your computer. Please refer to the T3 in Troubleshooting guide if you need assistance.
Note The product model shown in this QIG is TL-WA701ND, as an example. Assign a static IP address 192.168.1.100 for your computer. Please refer to the T3 in Troubleshooting guide if you need assistance.
More informationAssign a static IP address 192.168.1.100 for your computer. Please refer to the T3 in Troubleshooting guide if you need assistance.
Assign a static IP address 192.168.1.100 for your computer. Please refer to the T3 in Troubleshooting guide if you need assistance. Connect to the Access Point with the Ethernet cable or via wireless.the
More informationHow To Connect To A Wireless Network On Your Computer (Wired) Or Ipv) On A Computer (Wireless) On Your Ipv Or Ipa (Wired Or Wireless) On An Ipv (Wired/Wired) On Pc Or Mac
HI-SPEED INTERNET USER GUIDE Wireless Modem Router - 2704R 2013-11 VERSION 1-800-360-8555 TABLE OF CONTENTS 1. Installing Your Wireless Modem Router...4 1.1 Hardware Provided...4 1.2 Connecting Your Modem
More informationNetworking. General networking. Networking overview. Common home network configurations. Wired network example. Wireless network examples
Networking General networking Networking overview A network is a collection of devices such as computers, printers, Ethernet hubs, wireless access points, and routers connected together for communication
More informationTP-LINK TD-W8901G. Wireless Modem Router. Advanced Troubleshooting Guide
TP-LINK TD-W8901G Wireless Modem Router Advanced Troubleshooting Guide Released on 2009.09.25 Version 1.0 Content Summary... 3 Troubleshooting Flow Chart and Resolutions... 3 Check 1... 3 Check 2... 4
More informationBusiness Wireless Internet quick install guide
Read me first Business Wireless Internet quick install guide Wi-Fi and email set-up instructions included Actiontec Wireless Gateway TELUS Internet account information Record your personal account information
More informationNetwork & Internet Installation & Information Guide Fall 2004 Edition. Campus Ethernet For PCs using Windows 2000 & XP
Network & Internet Installation & Information Guide Fall 2004 Edition Campus Ethernet For PCs using Windows 2000 & XP Table of Contents Overview... 2 Requirements... 2 Physically connect your computer
More informationPCLinq2 Hi-Speed USB Bridge-Network Cable. Quick Network Setup Guide
PCLinq2 Hi-Speed USB Bridge-Network Cable Congratulations! Quick Network Setup Guide For Windows 98/ME/2000/XP Congratulations for installing the PCLinq2 Hi-Speed USB Bridge-Network Cable. This Quick Network
More informationSet Up E-mail Setup with Microsoft Outlook 2007 using POP3
Page 1 of 14 Help Center Set Up E-mail Setup with Microsoft Outlook 2007 using POP3 Learn how to configure Outlook 2007 for use with your 1&1 e-mail account using POP3. Before you begin, you will need
More informationEDGE FX Network configuration
Page 1 of 16 TITLE: Category: EDGE FX Network configuration GERBER EDGE Document Number: 4280 Supplied by: Gerber Service Last Modified: April 14, 2011 Summary: In order to connect an EDGE FX to your PC
More informationMovie Cube. User s Guide to Wireless Function
Movie Cube User s Guide to Wireless Function Table of Contents 1. WLAN USB Adapter Connection...3 2. Wireless Setup...4 2.1 Infrastructure (AP)...5 2.2 Peer to Peer (Ad Hoc)...7 2.3 Settings for PC...8
More informationTroubleshooting Guide
Troubleshooting Guide Before you start troubleshooting: Power down the Tooway modem for 60 seconds. Connect a computer directly (via Ethernet cable) to the Tooway modem Power the Tooway modem and wait
More informationNetwork Storage Link
A Division of Cisco Systems, Inc. WIRED Network Storage Link for USB 2.0 Disk Drives User Guide Model No. NSLU2 Copyright and Trademarks Specifications are subject to change without notice. Linksys is
More informationConfiguring TCP/IP Networking for Windows Me:
Configuring TCP/IP Networking for Windows Me: Configuration setup - Point and then right-click on the My Network Places icon on the desktop (see image below). Click/Select properties from the quick menu
More informationBefore you start, you should prepare the following items
Before you start, you should prepare the following items Windows 2000/XP/2003/Vista computer with print server setup CD USB Printer(non-GDI/CAPT) USB Printer cable One 802.11b/g Access Point (optional)
More informationHow to connect your new virtual machine to the Internet
This excerpt is taken from book Installing and Configuring SharePoint 2010 2 nd Edition. You can download this FREE ebook from the following link: http://walisystemsinc.com/installing_and_configuring_sharepoint2010_2nd_ed.php
More informationDetecting and Removing Spyware From Your Home Computer
Detecting and Removing Spyware From Your Home Computer Preamble: Spyware are programs that silently monitor and report on computing activities via the Internet. Companies use Spyware to target users with
More informationLinksys Gateway SPA2100-SU Manual
Linksys Gateway SPA2100-SU Manual Manuel de l'utilisateur Table of Contents Looking for Basic Setup Instructions?... 3 Most Recent Version of this Manual... 3 Advanced Setup Instructions... 4 Wiring Your
More informationGuide to Setting up Internet Connection Sharing for Windows
Guide to Setting up Internet Connection Sharing for Windows Document Date: December 20, 2005 Document Version: Version: 1.0 Disclaimer: Please note that this document is provided on an as is where is basis
More informationInstallation. Note The product model shown in this QIG is TD-W8951ND, as an example.
Installation The product model shown in this QIG is TD-W8951ND, as an example. Please use only wired network connections to configure the router. Power down all your network devices, including your computer(s)
More informationInternet. User guide
Internet User guide 2014-2015 1 TM Contents 1 2 3 4 5 6 7 8 9 10 11 Setting up your Internet Connecting Ethernet setup Wireless setup Registering Adding a device that has a Web browser Adding a device
More informationEASE Scan Tool Customers. SECTION I - Installation
Please Install Your EASE Scan Tool DVD Before Installing Any Other Software That Came With Your Package. SECTION I - Installation ATTENTION: Do NOT connect an EASE Vehicle Interface Device to your Computer
More informationUsing the Communication Ports on the DG-700 and DG-500 Digital Pressure Gauges
Using the Communication Ports on the DG-700 and DG-500 Digital Pressure Gauges 1. USB and Serial Communication Ports: Newer DG-700 and DG-500 gauges contain both a USB and a DB-9 Serial Communication Port,
More informationStudent Halls Network. Connection Guide
Student Halls Network Connection Guide Contents: Page 3 Page 4 Page 6 Page 10 Page 17 Page 18 Page 19 Page 20 Introduction Network Connection Policy Connecting to the Student Halls Network Connecting to
More informationLee County School Configuring Spec Ed Laptop Computers for Dialup, DSL/Cable Modem, and Wireless Access To the Internet
Lee County School Configuring Spec Ed Laptop Computers for Dialup, DSL/Cable Modem, and Wireless Access To the Internet Prepared by: Rich Morgan Technology Director Configuring your Spec Ed laptop for
More information