Operations Manual 1/18TH SCALE ARR PRO VERSION OF THE CHAMPIONSHIP WINNING XXX-T
|
|
|
- Calvin Perkins
- 8 years ago
- Views:
Transcription
1 1/18TH SCALE ARR PRO VERSION OF THE CHAMPIONSHIP WINNING XXX-T Operations Manual Introduction Thank you for choosing the Mini-T Pro from Team Losi Sport. This model requires you to install the Radio gear and fill the shocks with fluid. This guide contains these and the basic instructions for operating your new Mini-T Pro. It is critical that you read all of the instructions and all accompanying printed material in order to operate your model correctly and avoid unnecessary damage. Please take a moment to look them over before building the model. Copyright 2004 Team Losi A Division of Horizon Hobby Inc RT 11-04
2 Saftey Precautions This is a sophisticated radio controlled model that must be operated with caution and common sense. Failure to operate your Mini-T Pro in a safe and responsible manner could result in damage to the model and property. The Mini-T Pro is not intended for use by children without direct supervision. Team Losi and Horizon Hobby shall not be liable for any loss or damages, whether direct, indirect, special, incidental, or consequential, arising from the use, misuse, or abuse of this product or any product required to operate it. This model is controlled by a radio signal that is subject to interference from many sources outside your control. This interference can cause momentary loss of control so it is advisable to always keep a safety margin in all directions to aviod collisions. Always operate your model in an open area away from cars, traffic and people Never run out into the street for any reason. Never run your Mini-T Pro with low transmitter batteries Carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargable battery packs, etc.) that you use. Keep all chemicals, small parts and anything electrical out of the reach of children. Required Equipment 2 Channel Radio System with Receiver Electronic Speed Controller Micro size Servo Battery and Charger Radio Installation You will need a receiver, electronic speed control (ESC), and micro steering servo to complete your Mini-T Pro. If you do not already have these we suggest you use one of the newer smaller receivers and ESC s as it will be easier to fit these in the space available. All of the popular radio manufactures as well as Novak, GM Racing and LRP offer these items. We show mounting four of the most popular steering servos. Please note that in most cases we suggest the use of a servo saver as noted. 1) Cut a piece of double sided mounting tape to fit the bottom of both the receiver and ESC. Remove the paper backing from one side and apply to the bottom Do Not remove the remaining backing yet! 2) Test position the receiver and ESC on the top surface of the battery plate checking for adequate clearance and convenient access for all wiring. Mark or note these positions before proceeding. 3) Remove the protective backing from the mounting tape on the receiver and ESC. Carefully mount them on the battery plate. Final Connections Follow the radio manufactures instructions when making the final electronic connections. Specifically, the orientation of the color-coded wires in the various plugs where they plug into the receiver. If you plan on removing the wires attached to the motor mark the endbell with a + at the red wire and - at the black wire for future reference. Follow the radio instructions to set the proper steering and throttle movement. Follow the instructions included with the ESC for correct operation. Sample picture of electronics installed in the Mini-T Pro Airtronics 94091Z Recommended Servos HiTEC HS-55 HiTec HS-55 Hitec HS-55 JR Propo S241MG Carefully using a hobby knife, remove shaded material to open servo mounting hole as shown. Do this modification on both mounting ears. To install this servo, use the included Mini-T Servo Saver Kit and make modifications to servo as pictured above. Expert Electronics SL110 Airtronics 94091Z To install this servo you will need to purchase the Airtronics Micro Servo Saver kit. Expert Electronics SL110 To install this servo, use the included Mini-T Servo Saver Kit. Installing the Servo Use this hole to mount servos listed JR Propo S241MG (Metal Gear) At the time of this printing, a servo saver was not available. Using only the Metal geared version, follow the steps to modify the servo horn. LOSA6215 #4 Narrow Washer To install this servo, you will need to purchase LOSA6215 #4 Narrow Washer to space the mounting screw as pictured above. Install the Servo into the Chassis as shown in Figure 1. Insert the pins on the Servo Mounting Post into the holes in the Chassis. Move the Servo Posts slightly until both the left and right Posts are inserted in the holes in the Chassis. Next place the Chassis Brace on top of the Servo. The pins from both Servo Mounting Posts should line up with the holes on the Servo Brace. If they do not, move the Posts slightly until the pins fit into the holes. Secure the Brace to the Chassis with the four Phillips head screws as shown in Figure 2. Figure 1 Figure 2 Be sure that the taller pin is at the top
3 Making Adjustments The following are simple adjustments and easily maintained settings that will assure proper operation and performance. Since the Mini-T Pro comes from the factory with optimum settings, we suggest first-time R/C drivers leave these as they are and simply maintain them as necessary. Only after gaining experience should new drivers try experimenting with different settings. Chassis Tuning The Mini-T Pro has several adjustments available to you for tuning the performance for your needs. Although there are multiple shock positions and camber link locations provided, as noted above we have built the model with the best overall settings. The following are simple adjustments and easily maintained settings that will assure proper operation and performance. It is advised that when making any adjustment you do so in small increments and always check for other parts of the chassis that are affected. Steering Rate Your transmitter may be equipped with a steering rate control. This feature allows you to adjust the amount the front tires move when you turn the steering wheel. This is really helpful when you are on slick as well as high traction surfaces. If your Mini-T Pro turns too sharply and/or spins out easily, try decreasing the steering rate. For sharper or additional steering, try increasing the steering rate. Camber Camber is the angle of the tires to the racing surface when viewed from the front or rear of the truck. You want to keep both the front and rear tires straight up and down or leaning in at the top very slightly. If you are running on carpet or similar high traction surfaces you may find leaning them in a bit more helps. This adjustment is made with the turnbuckle links that extend from the front or rear bulkhead to the spindle carrier or rear hub. The Mini-T Pro is equipped with adjustable Titanium Turnbuckles that if turned one way (using the provided wrench) get shorter and if turned in No Camber Less Rate Full Rate More Camber the opposite direction get longer. Making these shorter increases the camber and lean-in of the tire while making them longer decreases the camber. Toe-In This is the relationship of the left and right side tires to one another. Ideally, you want the front of the tires to be pointed inward toward each other just slightly when viewed from above. This makes the model track straight and stable. This is controlled with the adjustable steering rods on either side. As you make them longer you will increase the toe-in and vice versa. No Toe-In More Toe-In Ride Height This is the height the chassis sits and runs at. There are spring spacers included with the Mini-T Pro that, when installed between the shock top and spring, will increase the pre-load on the spring and raise the chassis. You may want to try this when running on extremely rough surfaces. Setting The Gear Mesh The motor screws should be slightly loose. Slide the motor forward allowing the pinion gear to mesh with the spur gear. Snug (not tight) the bottom motor screw and try rocking the spur back and forth. There is a slight bit of movement before the motor is forced to turn over. If not, pull the top of the motor back slightly and recheck, there should be a slight bit of movement. If there is too much slop between the gears push the top of the motor forward. When set properly the wheels can be spun forward freely with very little noise. Make sure to tighten both motor screws and replace the gear cover before running. Ball Diff/Slipper Adjustment Instructions Always make sure your slipper will slip before the diff, as this will diminish the load on the differential and transmission. The diff should never slip. Hold the right tire and the spur gear in one hand and rotate the left tire. As you rotate the left tire, the slipper plate, and shaft should turn. This means the slipper is slipping before the differential. If the slipper shaft is not turning, your differential is slipping. You must either tighten the diff and/or loosen the slipper and recheck. To tighten the diff, remove the left side driveshaft and use a.050 Allen wrench and turn the diff screw clockwise in one-hour increments and recheck as noted above until it no longer slips. Any time you tighten the slipper you should check the diff as noted and tighten if necessary. Slipper Adjustments The Mini-T Pro is equipped with a Double Disk slipper device that offers both traction control and protection for the transmission. The slipper is primarily used to help absorb sudden impacts on the drive train due to landing big jumps or when using more powerful aftermarket motors and/or battery packs. Additionally, it can be used to smooth out the flow of power to the rear wheels and limit wheel spin when running on extremely slick surfaces. Adjustment is made by removing the access plug in the gear cover and turning the 3mm adjustment nut clockwise (to the right) to reduce the slip or counterclockwise (to the left) to increase the slip (Figure 3). When adjusted properly, you should be able to hold the rear tires firmly and barely be able to push the spur gear forward with your thumb (Figure 4). To track test, turn the Mini-T on and place it on the ground. As you push it backwards allowing it to roll freely, punch the throttle. The slipper should slip no more than an inch or two as it accelerates. With a 5 or 6 cell battery pack it should slip just a little. Make sure you replace the gear cover before running. LOSB1133 NEVER Let your differential slip! Follow the instructions below for proper operation and adjustment LOSB1134 LOSB1137 LOSB1135 LOSB1134 LOSB1135 LOSB1132 Increase Slip Figure 3 Figure 4 Reduce Slip More Pre-load Less Pre-load LOSB1131 (Bearings not included) *Gear Cover LOSB1136
4 Rebuilding The Ball Differential 1) Remove your ball differential from your tranny. 2) Remove left outdrive cup and loosen diff adjusting screw with a small flathead screw driver or a.050 allen wrench. Remove right side outdrive assembly. 3) Clean diff gear, diff rings and balls. If needed, replace worn parts and lube with Losi Silicone Diff Grease LOSA3065 4) Remove C clip from male oudrive half and carefully remove diff thrust assembly. 5) Clean all thrust components and replace if needed. Reassemble thrust components (Figure5). 6) Install thrust assembly into male oudrive as shown in (Figure 6). Install a new C Clip. 7) While holding male outdrive half install large diff washers, diff gear with balls. 8) Apply thread lock to diff screw and reassemble diff. Carefully bottom the diff screw out and back the screw out 1/16th of a turn. Your diff is now set. 9) Reassemble tranny. 10) Refer to Ball Diff/ Slipper Adjustment Instructions on the previous page. SYNTHETIC LUBRICANT LOSA3066 Fig 5. Washers should be stacked in this order Fig 6. Screwhead LOSB1129 LOSB1128 LOSB1126 LOSB1127 LOSB1125 LOSB1126 LOSB1128 LOSB1129 Filling and Maintaining the Racing Shock Absorbers Helpful Tools Filling and Bleeding Your Shocks 1. Remove the spring by pushing the lower spring cup away from the shock end and sliding Small Screwdirver 7mm Wrench Pliers it out, off of the shaft. 2. Unscrew the shock cartridge (7mm) and remove the shaft/cartridge/ piston assembly. 3. Use the included Team Losi 20 weight silicone fluid to fill the shock body to the bottom of the internal threads. 4. With the shaft half way through the cartridge, insert the piston into the fluid and start to thread the cartridge into the body approximately two turns. 5. With the cartridge loose, and holding the shock with the shaft up, push the shaft all the way in, allowing the excess fluid to escape. 6. Tighten the cartridge down (about 1/2 to 1 turn) being careful not to stripe the threads. 7. Move the shaft back and forth through its normal range of movement. There should be a costant resitance. If there is a greater resistance as the shaft is fully compressed, there is too much oil and it needs to be re-bled by following step #5. If there is less resistance at any point, there is not enough oil and you need to repeat steps #2 through #5. Otherwise, replace the spring and spring cup. NOTE: If leakage occurs where the cartridge seals to the shock body, you should replace the thin circular seal between the shock cartridge and shock body. Changing the Shock Cartridge 1. Remove the cartridge/assembly from the shock. 2. Remove the shock piston and the small e-clips above and below it. 3. Remove the old cartridge an dslide the new cartridge onto the shaft. Replace the e-clips and shock piston. Put a new seal onto the cartridge and follow steps #3 through #6 above. Changing the Pistons 1. Remove the cartridge/assembly from the shock. 2. Remove the e-clip from above the piston at the end of the shock shaft. 3. Replace the piston wit the one of you choice (small, medium or large hole. 4. Replace the e-clip and follow steps #3 through #6 above. NOTE: Always replace front or rear pistons in pairs-never just one piston. Battery Placement The Mini T Pro features a choice of battery positions. In the Back position, the Mini-T Pro will have a bit more traction and will jump nose high with less steering. In the Forward position, the Mini-T Pro will have more steering and jump with the nose down. Try playing with the different positions to find the best handling for your track. Battery Position Back Battery Position Forward Body Painting Before you start, please note the following tips. Use only paint that is designed for polycarbonate bodies or it may chip, flake, or cause the body to crack. Use quality masking tape (3M, Scotch, etc) or commercially available precut masks (XXX Main, Parma, etc) do not use clear sealing tape, as it is very difficult to remove. Always try to apply darker colors first. Backing a lighter color with white will produce a brighter appearance. Back white with a coat of silver (unless it is the last color applied) to prevent other colors from bleeding through. Always allow plenty of time for the paint to dry before pulling the tape or applying another color. 1) Wash the inside of the body with a little liquid detergent and warm water. 2) After drying thoroughly, position the precut window masks (supplied) to the inside of the body and firmly press them down for good adhesion. 3) Use masking tape or precut masks (not supplied) to the inside of the body to produce the pattern you desire. Try to tape the body so you will apply the darker colors first following the tips noted above. 4) Follow the paint manufactures instructions when applying the paint being careful not to allow it build up in any one spot. Remember to allow plenty of drying time between colors. 5) Remove the window masks and protective film from the outside of the body. Use R/C Body cleaner or Isopropyl Alcohol (do not use any hot solvents) to clean up any overspray etc. on the outside of the body if any, before applying the stickers.
5 Mini-T Pro Trouble Shooting Guide Doesn t operate Battery not charged or plugged in Charge battery / plug-in No crystal in receiver Check and replace if necessary No crystal in transmitter Check and replace if necessary Receiver switch not on Turn on receiver switch Transmitter not on or low battery Turn on / replace batteries Motor runs but rear Pinion not meshing with spur gear Adjust pinion/spur mesh wheels don t move Pinion spinning on motor shaft replace pinion gear on motor Slipper too loose Check & adjust slipper Differential slipping Adjust / check differential Drive pin in axle missing Check & replace Steering doesn t work Servo plug not in receiver Check if plug in / all the way Servo damaged Replace or repair servo Won t turn one direction Servo gears damaged Replace servo gears Motor doesn t run Motor plugs loose Plug-in completely Motor wire broken Repair or replace as needed ESC damaged Check with manufacture ESC gets hot Motor over geared Put smaller pinion on motor Driveline bound up Check wheels & trans for binds Poor run time and/or Batteries weak or low Check / replace battery pack sluggish acceleration Ni-Cad pack not fully charged Recharge Charger not allowing full charge Try another charger/power source Slipper slipping too much Check/adjust slipper & diff Differential slipping Tighten immediately Motor worn out Replace motor Driveline bound up Check wheels & trans for binds Poor range/glitches Transmitter battery low Check & replace as necessary Transmitter antenna loose Check & tighten Battery low in truck Replace or recharge Loose plugs or wires Check motor and power plugs Slipper won t adjust Drive pin missing in shaft Replace drive pin Slipper pads worn out Replace & adjust slipper
Convert your Losi Micro Vehicle from Brushed to Brushless power
Convert your Losi Micro Vehicle from Brushed to Brushless power Before we begin the conversion, let s make sure we have all the components you will need. Parts Required: A You will need a NEW servo to
Formula World GT 200 DRAFT COPY WWW.TEAMSPEEDMERCHANT.COM. f200.0.0d
DRAFT COPY WWW.TEAMSPEEDMERCHANT.COM f200.0.0d 2 Introduction, Supplies and Additional Equipment Congratulations on your purchase of a Speed Merchant Formula World GT 200 competition chassis. This instruction
Rebuild Instructions for 70001 and 70010 Transmission
Rebuild Instructions for 70001 and 70010 Transmission Brinn, Incorporated 1615 Tech Drive Bay City, MI 48706 Telephone 989.686.8920 Fax 989.686.6520 www.brinninc.com Notice Read all instructions before
Build Tips for Sakura Zero S
Build Tips for Sakura Zero S Revision Control Revision Revision Notes Report By Reviewed By Rev0 First Draft Marc Baynham Introduction The way in which a competition electric radio controlled car such
Service Manual Rol-Lift
R 2000 Service Manual Rol-Lift Series: T and E Developed by Generic Parts Service This manual is intended for basic service and maintenance of the Rol-Lift pallet jack. The pallet jacks you are servicing
INSTRUCTION MANUAL. Black Angel. www.copterx.com. Features. Kit Helicopter. Copyright 2009 KY MODEL Company Limited.
INSTRUCTION MANUAL Features - Carbon fiber main blade, tail blade, fly paddle, tail fin for extra weight saving and durability. - CNC machined high grade aluminum rotor head and tail gear box to ensure
STX ELECTRIC TOURING MODEL CAR 1:10SCALE STX-001 SOLID AXLE PULLEY ECCENTRIC CLAMP FRONT RIGHT - REAR LEFT ST03002-1
STX STX-001 ELECTRIC TOURING MODEL CAR 1:10SCALE ST03001 SOLID AXLE PULLEY ST03001-1 SOLID AXLE KIT ST03002-1 ECCENTRIC CLAMP FRONT RIGHT - REAR LEFT ST03002-2 ECCENTRIC CLAMP FRONT LEFT - REAR RIGHT ST03003
3/32" 19 21 22 7618 collet 23 24 BEFORE YOU RUN YOUR TRUCK PLEASE READ THIS SECTION OF THE MANUAL FIRST. AFTER YOU READ THIS SECTION, READ YOUR ENGINE MANUAL BEFORE YOU START YOUR ENGINE FINAL ADJUSTMENTS
Operating Instructions Parts List Manual Scissor Lift Pallet Truck
Operating Instructions Parts List Manual Scissor Lift Pallet Truck Note: Operator MUST read and understand this operating instructions before use this Hand Scissor Lift. Thank you for using this hand scissors
SCION tc 2005-2008 COIL OVER SUSPENSION Preparation
SCION tc 2005-2008 COIL OVER SUSPENSION Preparation Part Number: PTR11-21070 NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: Item # Quantity Reqd. Description
Register your Losi Product Online. Notice. Connect - Register - Win. Meaning of Special Language. Losi/Horizon Support. Kit Contents.
Operation Manual Not responsible for errors. Losi, a Division of Horizon Hobby, Inc. Before operating this vehicle, please read all printed materials thoroughly. Notice All instructions, warranties and
6 inch A-Arm Lift Kit WARNING: 16-018/16-019. installation instructions. will fit CLUB CAR DS. included:
Revised May 205 6-08/6-09 6 inch A-Arm Lift Kit will fit CLUB CAR DS installation instructions included: Rear Lift Blocks Main Suspension Assembly Spindles A-Arms Rear Shock Mounting Plates U-Bolts WARNING:
DiscPlus DX195 and DX225 Air Disc Brakes
Revised 11-04 Technical Bulletin Revised 1 Technical 11-04 Bulletin DiscPlus DX195 and DX225 Air Disc Brakes Inspection, Installation and Diagnostics Air Disc Brake Inspection Intervals and Procedures
SLACK PERFORMANCE KARTS
SLACK PERFORMANCE KARTS SET UP GUIDE Thank you for purchasing a 2013 Slack Axiom Chassis. Performance Mfg. strives to provide you with the very best chassis and components on the market today. Your satisfaction
MODEL 6804R. owner s manual supplement
MODEL 6804R owner s manual supplement SLASH 4x4 PLATINUM EDITION Introduction Thank you for choosing the Traxxas Slash 4x4 Platinum Edition. We believe you have purchased the most technologically advanced,
E4RS/JS/JR II/III Parts List
E4RS/JS/JR II/III Parts List Copyright: Lionel Troyon / HRC Distribution www.teammagicrc.net 03.12.2015 KF2201 Front Spool Set with Aluminium Outdrives REPLACED BY TM507213 KF2201 1 Front Spool Joints
Drive shaft, servicing
Volkswagen Passat B6 - Drive shaft, servicing Стр. 1 из 41 40-7 Drive shaft, servicing Drive shafts, overview I - Assembly overview: Drive axle with CV joint VL100 40-7, Drive axle with CV joint VL100,
DANA 30 MANUAL HUB CONVERSION KIT
DANA 30 MANUAL HUB CONVERSION KIT 12194 PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE YOU BEGIN Your safety and the safety of other motorists is very important. Your Jeep is an off road capable vehicle
POSEIDON 2-29, 2-25 & 2-22 POSEIDON 2-29, 2-25 & 2-22 XT
POSEION 2-29, 2-25 & 2-22 POSEION 2-29, 2-25 & 2-22 XT Repair Manual Index A. Safety precautions 3 B. Technical data 4 C. Structure 5-6. Service / Repair 7-23 E. Tools 24 F. Function 25-26 G. Electric
Pallet Jack. OWNER S MANUAL Model MH1230. Important Safety Instructions Assembly Instructions Parts and Hardware Identification
OWNER S MANUAL Model MH1230 Important Safety Instructions Assembly Instructions Parts and Hardware Identification Pallet Jack CAUTION: Read, understand and follow ALL instructions before using this product
LOSB9595 1/36 th Brushless ESC and 10250Kv Motor Combination
LOSB9595 1/36 th Brushless ESC and 10250Kv Motor Combination Thank you for purchasing this Losi High Performance Brushless System! This technically advanced system will offer maintenance free operation,
13. REAR WHEEL/BRAKE/SUSPENSION
13. REAR WHEEL/BRAKE/SUSPENSION 13 3.5~4.5kg-m 8.0~10.0kg-m 0.8~1.2kg-m 3.0~4.0kg-m 2.4~3.0kg-m 3.5~4.5kg-m 6.0~8.0kg-m 13-0 13. REAR WHEEL/BRAKE/SUSPENSION 13 REAR WHEEL/BRAKE/SUSPENSION SERVICE INFORMATION...
AXLE SHAFTS - FRONT. 1998 Pontiac Bonneville MODEL IDENTIFICATION DESCRIPTION & OPERATION TROUBLE SHOOTING REMOVAL & INSTALLATION
AXLE SHAFTS - FRONT 1998 Pontiac Bonneville 1998-99 DRIVE AXLES FWD Axle Shafts - Cars - "C", "G" & "H" Bodies GM Aurora, Bonneville, Eighty Eight, LeSabre, LSS, Park Avenue, Regency, Riviera MODEL IDENTIFICATION
SERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12" DUAL BEVEL COMPOUND MITER SAW B27A
PAGE 1 OF 6 BASE ASSEMBLY 00 0 EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS 1 02-80-0050 Thrust Bearing (1) 2 05-80-0510
Build Your Own Solar Car Teach build learn renewable Energy! Page 1 of 1
Solar Car Teach build learn renewable Energy! Page 1 of 1 Background Not only is the sun a source of heat and light, it s a source of electricity too! Solar cells, also called photovoltaic cells, are used
EXPLODED VIEWS AND PARTS LIST
INTRODUCTION Serpent created this racing car for the competitive electric 1/12th scale pan car class as the S120-L, which like all our previous cars, has been designed to win straight from the box. Featuring
Street-Lynx. Reilly MotorSports, Inc. Installation Manual
Street-Lynx By Reilly MotorSports, Inc. Installation Manual 1 1- Begin by removing your original rear suspension disconnect your brake lines, E-brake cables, and remove the driveshaft. To prevent fire
TABLE OF CONTENTS. Section 1 - Assembling your new pit bike.
Orion Pit Bike Sales Owners Manual (All information and content is the property of Orion Pit Bike Sales. Any attempt to copy or resell is a direct violation of our copyright. All violators will be prosecuted)
Parts#MB003-003 Reverse Gear MAMBA (Monoblock for Cable operated) For 5 speed Trans., '87 to '06 Big Twin models (except '06 Dyna)
Installation Instructions Reverse Gear MAMBA (Monoblock for Cable operated) Read and become familiar with these installation instructions before start. Two Piece for H-D 5 Speed Trans., Cable operated
Owners & Installation Manual for the Sheridan, Mountainair, Pine Valley and Old Forge Ceiling Fan Family
Owners & Installation Manual for the Sheridan, Mountainair, Pine Valley and Old Forge Ceiling Fan Family Part of the Kiva Lighting Family Custom Lighting and Fans Since 1992 1312 12th St NW Albuquerque,
TUNING SECTION ABOUT ADJUSTMENTS
TUNING SECTION ABOUT ADJUSTMENTS R/C race trucks, in general, are some of the most adjustable racing machines of any scale. What s really amazing is just how easy and quick it is to make all of our changes:
White Industries Rear Hub Instructions
White Industries Rear Hub Instructions Tool required: 2mm allen/hex wrench, 19mm socket, 20mm socket, and mallet. 1. Loosen the set screws located in the adjusting collar by using a 2mm allen wrench inserted
300 SERIES 331, 332, 333, 344, 356 AND 367 MODELS
Section: MOYNO 500 PUMPS Page: 1 of 8 Date: March 1, 1998 SERVICE MANUAL MOYNO 500 PUMPS 300 SERIES 331, 332, 333, 344, 356 AND 367 MODELS Mechanical Seal Models Packing Gland Models MODELS DESIGN FEATURES
Gripper Kit for the Boe-Bot Robot (#28202)
599 Menlo Drive, Suite 100 Rocklin, California 95765, USA Office: (916) 624-8333 Fax: (916) 624-8003 General: info@parallax.com Technical: support@parallax.com Web Site: www.parallax.com Educational: www.stampsinclass.com
Installation Guide for the TJ LCG PRO Suspension System (Low Center of Gravity) Available 4 or 5
INSTALLATION GUIDE Installation Guide for the TJ LCG PRO Suspension System (Low Center of Gravity) Available 4 or 5 Take every precaution to make this installation a safe procedure. Make safety the number
HYDRAULIC LIFT TABLE CART 2200-LB.
HYDRAULIC LIFT TABLE CART 2200-LB. OWNER S MANUAL WARNING: Read carefully and understand all MACHINE ADJUSTMENT AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other
Step-by-step instructions:
Spark plug thread repair for Ford Triton cylinder heads Step-by-step instructions: Identification Installation Verification Specifically designed and tested for 4.6L, 5.4L, and 6.8L 2 and 4 valve heads,
Verify caster, camber and toe-in are correct before proceeding.
If rotating the tie rod end 360 degrees changes the toe-in too much, use the rack tie rod to make smaller adjustments. Put the tie rod end in the steering arm and snug the castle nut before adjusting.
Slide the new steering column shaft through the steering column from the driver compartment.
Slide the new steering column shaft through the steering column from the driver compartment. Push the column shaft through the steering column until the machined end is out past the column lower bushing.
Joplin Rebuild Instructions
Joplin Rebuild Instructions This is a step by step list of instruction on how to rebuild the Crankbrothers Joplin post. It may not always be required to completely tear-down the post to do the work needed
CorkSport Mazdaspeed 6 Rear Sway Bar 2006-2007 Mazdaspeed 6
CorkSport Mazdaspeed 6 Rear Sway Bar 2006-2007 Mazdaspeed 6 Pre-Installation Notes: The CorkSport Rear Sway Bar is a great addition to improving the handling performance to the Mazdaspeed 6. It will minimize
Thank You For Choosing. INSTALLATION INSTRUCTIONS Portal Gear Hubs Polaris RZR 800. (installation performed on 60 Model) (Right) (Left)
740B Clifty Drive Madison, Indiana 47250 812-574-7777 INSTALLATION INSTRUCTIONS Portal Gear Hubs Polaris RZR 800 A (installation performed on 60 Model) Item Description Qty A Rotor 4 B Gear Box, L 2 C
MGB Chrome Bumper Conversion
MGB Chrome Bumper Conversion Installation Instructions For 1974 1/2-1980 MGB This kit requires cutting, welding, and painting. Professional installation recommended. Note: Every MGB body is slightly different
Micro Cart User's Guide
Micro Cart User's Guide To take full advantage of the ergonomic features of your new Sun Mountain Micro Cart, please read the following information. SUN MOUNTAIN 1 Your Micro Cart has several innovative
Wiper Motor Marinco 2.5. Installation Instructions
Wiper Motor Marinco 2.5 Installation Instructions Wiper Motor Marinco-2.5 The Marinco 2.5 Wiper Motor Offers the Following Features: Fully sealed base and housing which allows installation in outdoor wet
1/10 SCALE 4x4 TRUCK KIT
1/10 SCALE 4x4 TRUCK KIT Recommended Tools Hex Drivers (1.5mm, 2mm, 2.5mm) Thread Lock Cross Wrench Long Nose Pliers Tips for Assembly Use good quality hex drivers to avoid stripping screw heads. Use thread
2100 AD 015 0009 Mirror Elevator Ball Nut Replacement Procedure
2100 AD 015 0009 Mirror Elevator Ball Nut Replacement Procedure Derek Guenther 1/28/2015 Rev. Purpose The purpose of this document is to describe the procedure necessary to replace one of the ball nuts
Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 46 Brakes - Mechanical Components (Page GR-46)
46 Brakes - Mechanical Components (Page GR-46) Front brakes Brake pads, removing and installing Brake pads, removing and installing FN 3 brake caliper, servicing FS III brake caliper, servicing Rear wheel
TABLE OF CONTENTS. I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2
BAL Accu-Slide System I. Table of Contents TABLE OF CONTENTS I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2 II. GETTING STARTED... 5 - Section 2.01: Tools You Will Need... 5 - Section
Rating when used as a weight carrying hitch without spring bars:
BOLT-TOGETHER WEIGHT DISTRIBUTING HITCH SYSTEM Rating when used as a weight distributing hitch with spring bars: Part Number 48051 4805 48053 48054 Max Tongue Weight 550 Ibs. 750 Ibs. 1000 Ibs. 1400 lbs.
HYDRAULIC TABLE CART 500-LB.
HYDRAULIC TABLE CART 500-LB. OWNER S MANUAL WARNING: Read carefully and understand all MACHINE ADJUSTMENT AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic
Table of Contents. Overview 1. Pump Disassembly 2. Control Disassembly / Reassembly 7. Pump Reassembly 13. Adjustment Procedures DR Control 19
Table of Contents Overview 1 Pump Disassembly 2 Control Disassembly / Reassembly 7 Pump Reassembly 13 Adjustment Procedures DR Control 19 Adjustment Procedures DRG Control 20 Adjustment Procedures DFR
SELF-STEERING AXLE TABLE OF CONTENTS
SELF-STEERING AXLE TABLE OF CONTENTS Section 1 - Introduction Section 2 - Pre-Installation Check List Section 3 - Ride Height Adjustments Section 4 - Suspension Mount Section 5 - Axle Mount Section 6 -
INSTALLATION INSTRUCTIONS COMPETITION SERIES COILOVER SUSPENSION SYSTEM 03+ Scion xb
INSTALLATION INSTRUCTIONS COMPETITION SERIES COILOVER SUSPENSION SYSTEM 03+ Scion xb NOTE: Progress Technology products should only be installed by a qualified licensed mechanic experienced in the installation
Build a Junior Solar Sprint Model Car Kit Materials: 1 PITSCO Ray Catcher Sprint Kit or Solar Made Junior Solar Sprint Kit 1 White Sheet of Plastic
Build a Junior Solar Sprint Model Car Kit Materials: 1 PITSCO Ray Catcher Sprint Kit or Solar Made Junior Solar Sprint Kit 1 White Sheet of Plastic Coated Paper 2 Balsa Sheets (10-1/2 x4 x3/16 ) 2 Alligator
M113 VEHICLE FAMILY RUBBER TRACK INSTALLATION INSTRUCTIONS SOUCY TRACK SYSTEM 04-M113-1ENS (SPLIT IDLER) Litho d in Canada 1 04-M113-1ENS
M113 VEHICLE FAMILY RUBBER TRACK INSTALLATION INSTRUCTIONS (SPLIT IDLER) 1 # TABLE OF CONTENTS List of parts and tools................................................3 Installation of complete kit...................................................5
MKV Golf GTI Rear Brake Service - Replace Pads and Rotors
Page 1 Installation Procedures MKV Golf GTI Rear Brake Service - This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation of
Thank You For Choosing. INSTALLATION INSTRUCTIONS Portal Gear Hubs Polaris RZR XP 900 Crew. (Right) (Left)
740B Clifty Drive Madison, Indiana 47250 812-574-7777 INSTALLATION INSTRUCTIONS Portal Gear Hubs Polaris RZR XP 900 Crew A Item Description Qty A Rotor 4 B Gear Box, L 2 C Gear Box, R 2 D Gasket 4 E Cap
Gravity Racing Challenge STEM Team Competition Open Class High School Division Car Assembly Plans And Rules
Gravity Racing Challenge STEM Team Competition Open Class High School Division Car Assembly Plans And Rules 1 Table Of Contents Introduction...Page 3 Floorboard...Page 4 Step One Steering Stop Installation...Page
ROTOR LOADER OWNER S MANUAL
ROTOR LOADER OWNER S MANUAL ROTOR LOADER OWNER S MANUAL WARNING IMPORTANT SAFETY INSTRUCTIONS AND GUIDELINES. Misuse of paintball equipment may cause serious injury or death. QUICK SET-UP GUIDE BATTERY
DYNA RIDER FOOTBOARD KIT
-J0 REV. 0-0-0 DYNA RIDER FOOTBOARD KIT GENERAL Kit Number 000 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English
Char-Lynn Hydraulic Motor. Repair Information. 10 000 Series. October, 1997
Char-Lynn Hydraulic Motor October, 1997 Repair Information Geroler Motor Two Speed 001 27 Retainer inside bore of valve plate bearingless motors only 4 15 16 3 6 35 Parts Drawing 25 2 2 1 19 17 36 40 47
This instruction is valid for all ACD pump models shown on page 2
Screw pumps ACD Maintenance and Service Instruction This instruction is valid for all ACD pump models shown on page 2 Contents Page List of components 2 Exploded view/ordering code 3 Service intervals
S&W Race Cars and Components, Inc.
S&W Race Cars and Components, Inc. 11 Mennonite Church Road Spring City, PA 19475 TECH & INFORMATION: 610-948-7303 ORDERS: 1-800-523-3353 OFFICE FAX: 610-948-7342 E-Z INFO FAX 610-792-1234 CAUTION!!! -
THE CANON 106 TONER CARTRIDGE
THE CANON 106 TONER CARTRIDGE DOC# 0381 By Mike Josiah and the Technical Staff at Summit Technologies CANON 106 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS Page 1 Remanufacturing the Canon ImageClass
SECTION G2: CABLE PROCESSOR MODULE MAINTENANCE
SECTION G2: CABLE PROCESSOR MODULE MAINTENANCE Cable Processor Module overview WARNING! When tipping the Cable Processor Module back, (after removing the toggle arm pin), use extreme caution not to drop
Overview PARTS LIST. B. Lever mounting base C. Flush handle assembly D. Grey/Blue float stop E. Grey float (Full Flush) F. Flush valve washer
Overview READ ENTIRE INSTRUCTIONS BEFORE STARTING INSTALLATION PARTS LIST A. Flush valve B. Lever mounting base C. Flush handle assembly D. Grey/Blue float stop E. Grey float (Full Flush) F. Flush valve
PRODUCT MANUAL - M090
PRODUCT MANUAL - M090 MODEL 203/266 ELECTRIC CAN OPENER 1 SAFETY CAUTION: SEVERED CAN LIDS HAVE CUTTING EDGES. USE OF A PROTECTIVE GLOVE OR TONGS IS ADVISED WHEN HANDLING LIDS. WARNING To avoid risk of
TRANS-05, Torque Tube Removal, Rebuilding, and Installation
TRANS-05, Torque Tube Removal, Rebuilding, and Installation Tools Metric Wrench Set Metric Socket Set Jack Stands (6 minimum) Floor Jack 8mm Cheesehead socket (also referred to as 12 point internal socket
Unit: mm(in) Item Standard value Service limit Axle shaft run out - 0.2(0.008)
Rear Wheel/Brake/Suspension 13. Rear Wheel/Brake/Suspension Service Information 13-1 Troubleshooting 13-2 Rear Wheel 13-3 Rear Cushion 13-4 Rear Swing Arm 13-7 Service Information General Safety If the
KEYPAD LOCK RETROFIT KIT
KEYPAD LOCK RETROFIT KIT INSTRUCTIONS FOR ASSEMBLY IMPORTANT READ & SAVE THESE INSTRUCTIONS Tools Required for Assembly 5/32 hex (Allen) wrench #2 Phillips screwdriver Isopropyl alcohol or alcohol wipes
Range Road RR Series Semi-Automatic Firewood Processor. Crated Unit Assembly Manual
Range Road RR Series Semi-Automatic Firewood Processor Crated Unit Assembly Manual 1 1) Undo 8-18mm x 19mm Nuts and bolts, 2 on each leg of top frame 2) Lift top of Metal crate off and move out of work
16 April 2012 1032011-F 1994-2002 Dodge Adjustable Track bar with Relocation Bracket 1
16 April 2012 1032011-F 1994-2002 Dodge Adjustable Track bar with Relocation Bracket 1 BD Adjustable Track Bar w/bracket Dodge 2500-3500 4WD Models 1994-2002 Dodge 1500 4WD Model 1994-2001 P/N# 1032011-F
ARTICLE BEGINNING APPLICATION IDENTIFICATION DESCRIPTION LUBRICATION & ADJUSTMENT TROUBLE SHOOTING. MANUAL TRANSMISSIONS Saab 5-Speed Transaxle
Article Text ARTICLE BEGINNING MANUAL TRANSMISSIONS Saab 5-Speed Transaxle APPLICATION TRANSMISSION APPLICATION ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Vehicle Application Transmission
PALLET JACK - 2.5 TON
PALLET JACK - 2.5 TON 39939 SET UP AND OPERATING INSTRUCTIONS Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury.
Tri-Homo Style Operation and Maintenance Instructions
Tri-Homo Style Operation and Maintenance Instructions One Research Drive Stratford, CT 06615 (203) 375-0063 www.sonicmixing.com 1 Installation and Start-up Do not perform following adjustments without
STEERING HANDLEBAR/FRONT WHEEL/ FRONT SHOCK ABSORBER
14 14 STEERING HANDLEBAR/FRONT WHEEL/ SCHEMATIC DRAWING ------------------------------------------------- 14-1 SERVICE INFORMATION------------------------------------------------ 14-2 TROUBLESHOOTING-----------------------------------------------------
(A4) Suspension and Steering Sample Questions and Answers
(A4) Suspension and Steering Sample Questions and Answers Answers to these questions are found beginning on page 4 of this document 1. Two technicians are discussing the replacement of an inner tie rod
Fuel Injection Pump, Rotary (005-014)
Fuel Injection Pump, Rotary View Related Topic Page 1 of 30 Fuel Injection Pump, Rotary (005-014) Table of Contents Summary General Information Preparatory Steps Remove Front Gear Train Rear Gear Train
Quest for Speed. Discover Engineering. Youth Handouts
Discover Engineering Youth Handouts Activity 1: Spooling Around Name: Date: Materials List Wooden spool Nail Flat washer Rubber bands Craft stick Nut Tape measure Calculator Masking tape Procedure 1. To
Speed-Mat Rectangle Cutter
Speed-Mat Rectangle Cutter 1 Honeycomb baseboard. 2 Left hold down. 14 3 Bottom hold down. 4 4 Left / right rule. 8 5 8 5 Left / right rule pointer. 1 6 Top / bottom rule. 7 Top / bottom rule pointer.
MEASURING WHEEL ALIGNMENT
MEASURING WHEEL ALIGNMENT 2003-04 WHEEL ALIGNMENT Specifications & Procedures - Hummer - H2 Steering and vibration complaints are not always the result of improper alignment. One possible cause is wheel
Ford F-Series Column Shift Repairs
Ford F-Series Column Shift Repairs I ve had it on my list to tighten up the linkage on my 52 s column shift setup for a long time. I tried to get it apart when I had all the front end sheet metal off,
Front brakes (FN- 3), servicing
j a t Front brakes (FN- 3), servicing 46-1 Front brakes, servicing Note: Install complete repair kit. After replacing brake pads and before moving vehicle, depress brake pedal several times firmly to properly
Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 47 Brakes - Hydraulic Components (Page GR-47)
47 Brakes - Hydraulic Components (Page GR-47) FS III front brake calipers, servicing Front brake caliper piston, removing and installing FN 3 front brake calipers, servicing Front caliper piston, removing
PEDAL CAR - GO CART ASSEMBLY & OPERATING INSTRUCTIONS
PEDAL CAR - GO CART 42822 ASSEMBLY & OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at: http://www.harborfreight.com Copyright 2000 by Harbor Freight Tools. All
ASSOCIATED 1:10 SCALE T3 MANUAL
ASSOCIATED 0 SCALE T3 MANUAL INSTRUCTION MANUAL FOR THE RC10T3 ELECTRIC TRUCKS #7003, 7013, 7038, 7048 ASSOCIATED S RC10T3 TRUCK-- READER S CHOICE OF THE YEAR TIMES! Radio Control Car Action magazine,
DO NOT attempt to repair hub and wheel bearing assembly.
Page 1 of 6 HUB & WHEEL BEARINGS (WITH PULSE VACUUM HUBLOCK) DO NOT attempt to repair hub and wheel bearing assembly. Removal DO NOT remove hub lock assembly by prying on hub lock legs. This can crack
2006 HEADSHOK Service Video #1
LEFTY SPEED DLR DAMPING CARTRIDGE This document explains how to properly remove, disassemble, inspect, reassemble and reinstall the Lefty Speed DLR2 damping cartridge. It is a document to be used in conjunction
STEERING SYSTEM - POWER
STEERING SYSTEM - POWER 1990 Nissan 240SX 1990 STEERING Nissan - Power Rack & Pinion Axxess, Maxima, Pulsar NX, Sentra, Stanza, 240SX, 300ZX DESCRIPTION The power steering system consists of a rack and
Instructions and precautions. Fork Height. Visit our website at: http://www.harborfreight.com
Pallet Jack Item 68760 / 68761 Instructions and precautions Specifications Capacity Control Lever Fork Height Fork Length Fork Width Maximum Minimum Width over Forks Steering Wheel Dia. 2-1/2 Ton (5,000
Trillium 40 Axis Spring Tensioner Wire Replacement Instructions
Trillium 40 Axis Spring Tensioner Wire Replacement Instructions 1 Overview The objective is to replace the broken axis spring tensioner wire. This requires the following tasks: 1. Remove the seismometer
2005-2007 Ford Focus Front Brake Rotors
2005-2007 Ford Focus Front Brake Rotors Replacement Replacing the rotors in 2005-2007 Ford Focus models with rear drum brakes. Written By: David Hodson INTRODUCTION The steps in this guide are used to
http://waterheatertimer.org/troubleshoot-rheem-tankless-water-heater.html
http://waterheatertimer.org/troubleshoot-rheem-tankless-water-heater.html TECHNICAL SERVICE DEPARTMENT Removal, Cleaning, & Reinstallation of the Burner Assembly For models 74 & GT199 Required tools -
Guide for Modified Assembly: Lightning McQueen. By: Collin Patterson, University of Delaware. Materials and Tools:
Guide for Modified Assembly: Lightning McQueen By: Collin Patterson, University of Delaware Materials and Tools: PVC o 40 inches of 1 in diameter PVC o 25 inches of ¾ in PVC o 4 x 1 in elbows o 2 x ¾ in
INSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5
CI100018 INSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5 Rabbit, Jetta 2.5L These instructions are applicable to vehicles equipped with either manual or automatic transmissions Thank you for choosing to
Solstice/Sky Water Pump Replacement
Solstice/Sky Water Pump Replacement The water pump on the Solstice/Sky is starting to need replacement on some vehicles. This guide will help in replacing the water pump while the engine is still in the
12. REAR WHEEL/BRAKE/SUSPENSION
12 12 12-0 SERVICE INFORMATION... 12-1 REAR BRAKE... 12-5 TROUBLESHOOTING... 12-2 REAR SHOCK ABSORBER... 12-8 REAR WHEEL... 12-3 REAR FORK... 12-9 SERVICE INFORMATION GENERAL INSTRUCTIONS When installing
Contents. Front Derailleurs... 2. Part One - Planning... 2 I. Objectives... 2 II. Materials Needed... 2 III. Setting...2 IV. Evaluation...
Contents... 2 Part One - Planning... 2 I. Objectives... 2 II. Materials Needed... 2 III. Setting...2 IV. Evaluation... 2 Part Two - Activity Instructions... 3 Steps to Adjusting and Replacing... 3 Disassemble...
Make these adjustments before racing
FINAL ADJUSTMENTS ADJUSTING CAMBER To set the camber we recommend using our supplied #1719 camber/rear toe-in gauge. When adjusting camber you need to have the car ready to run with no body. Make these