Network Video Recorder User Manual

Size: px
Start display at page:

Download "Network Video Recorder User Manual"

Transcription

1 Network Video Recorder User Manual UD.6L0202D1289A01

2 Hikvision Network Digital Video Recorder User Manual This manual, as well as the software described in it, is furnished under license and may be used or copied only in accordance with the terms of such license. The content of this manual is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by Hikvision Digital Technology Co., Ltd. (Hikvision). Hikvision assumes no responsibility or liability for any errors or inaccuracies that may appear in the book. Except as permitted by such license, no part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission of Hikvision. HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THE HIKVISION SOFTWARE. HIKVISION DOES NOT WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE HIKVISION SOFTWARE IN TERMS OF ITS CORRECTNESS, ACCURACY, RELIABILITY, CURRENTNESS, OR OTHERWISE. THE ENTIRE RISK AS TO THE RESULTS AND PERFORMANCE OF THE HIKVISION SOFTWARE IS ASSUMED BY YOU. THE EXCLUSION OF IMPLIED WARRANTIES IS NOT PERMITTED BY SOME STATES. THE ABOVE EXCLUSION MAY NOT APPLY TO YOU. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, AND THE LIKE) ARISING OUT OF THE USE OR INABILITY TO USE THE HIKVISION SOFTWARE EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. 2

3 Regulatory information FCC information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC. 2002/96/EC (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: 3

4 Preventive and Cautionary Tips Before connecting and operating your device, please be advised of the following tips: Ensure unit is installed in a well-ventilated, dust-free environment. Unit is designed for indoor use only. Keep all liquids away from the device. Ensure environmental conditions meet factory specifications. Ensure unit is properly secured to a rack or shelf. Major shocks or jolts to the unit as a result of dropping it may cause damage to the sensitive electronics within the unit. Use the device in conjunction with an UPS if possible. Power down the unit before connecting and disconnecting accessories and peripherals. A factory recommended HDD should be used for this device. Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. 4

5 Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. The figures in the manual are for reference only. This manual is applicable to the models listed in the following table. Series Model Type 7100NI-SL DS-7104NI-SL DS-7108NI-SL Network Video Recorder 7100NI-SL/W DS-7104NI-SL/W Network Video Recorder 7100NI-SN 7100NI-SN/N 7100NI-SN/P 7600NI-SN 7600NI-SN/N 7600NI-SN/P DS-7104NI-SN DS-7108NI-SN DS-7116NI-SN DS-7104NI-SN/N DS-7108NI-SN/N DS-7116NI-SN/N DS-7104NI-SN/P DS-7108NI-SN/P DS-7116NI-SN/P DS-7604NI-SN DS-7608NI-SN DS-7616NI-SN DS-7604NI-SN/N DS-7608NI-SN/N DS-7616NI-SN/N DS-7604NI-SN/P DS-7608NI-SN/P DS-7616NI-SN/P Network Video Recorder Network Video Recorder Network Video Recorder Network Video Recorder Network Video Recorder Network Video Recorder 5

6 Product Key Features General Connectable to network cameras, network dome and encoders. Connectable to the third-party network cameras like AXIS, Brickcom, Bosch, PANASONIC, SAMSUNG and SANYO, and network cameras that adopt ONVIF or PSIA protocol. PAL/NTSC adaptive video inputs. Each channel supports dual-stream. Up to 16 network cameras can be connected. Independent configuration for each channel, including resolution, frame rate, bit rate, image quality, etc. The quality of the input and output record is configurable. Local Monitoring Simultaneous HDMI and VGA outputs. HDMI output and VGA output at up to resolution. Multiple screen display in live view is supported, and the display sequence of channels is adjustable. Live view screen can be switched in group, and manual switch and auto-switch live view are also provided, and the interval of auto-switch can be adjusted. Quick setting menu is provided for live view. Motion detection, tamper-proof, video exception alert and video loss alert functions. Privacy mask. Multiple PTZ protocols supported; PTZ preset, patrol and pattern. Zooming in by clicking the mouse and PTZ tracing by dragging mouse. HDD Management Up to 2 SATA hard disk can be connected, with a maximum of 4TB storage capacity. Support S.M.A.R.T. and bad sector detection. HDD quota management; different capacity can be assigned to different channel. Recording and Playback Holiday recording schedule configuration. Continuous and event video recording parameters. Multiple recording types: manual, normal, alarm, motion, motion alarm, motion & alarm. 8 recording time periods with separated recording types. Pre-record and post-record for alarm, motion detection for recording, and pre-record time for schedule and manual recording. Searching record files by events (alarm input/motion detection). Tag adding for record files, searching and playing back by tags. Locking and unlocking record files. Searching and playing back record files by channel number, recording type, start time, end time, etc. Zooming in when playback. Reverse playback of multi-channel. Supports pause, play reverse, fast forward, slow forward, skip forward, and skip backward when playback, and locating by dragging the mouse. Up to 8-ch synchronous playback at 720P real time. 6

7 Backup Export video data by USB or SATA device. Export video clips when playback. Management and maintenance of backup devices. Alarm and Exception Configurable arming time of alarm input/output. Alarm for video loss, motion detection, tampering, abnormal signal, video input/output standard mismatch, illegal login, network disconnected, IP confliction, abnormal record, HDD error, and HDD full, etc. Alarm triggers full screen monitoring, audio alarm, notifying surveillance center, sending and alarm output. Automatic restore when system is abnormal. Other Local Functions Operable by mouse and remote control. Three-level user management; admin user is allowed to create many operating accounts and define their operating permission, which includes the limit to access any channel. Operation, alarm, exceptions and log recording and searching. Manually triggering and clearing alarms. Import and export of device configuration information. Network Functions 1 self-adaptive 10M/100M/1000M network interface for DS-7116NI-SN, DS-7116NI-SN/N, DS-7116NI-SN/P, DS-7616NI-SN, DS-7616NI-SN/N and DS-7616NI-SN/P, and 1 self-adaptive 10M/100M network interface for other models. Up to 8 independent PoE network interfaces are provided for DS-7600NI-SN/P and DS-7100NI-SN/P series. Up to 8 independent built-in switch network interfaces are provided for DS-7600NI-SN/N and DS-7100NI-SN/N series. IPv6 is supported. TCP/IP protocol, PPPoE, DHCP, DNS, DDNS, NTP, SADP, SMTP, NFS, and iscsi are supported. TCP, UDP and RTP for unicast. Auto/Manual port mapping by UPnP TM. Remote reverse playback via RTSP. Support accessing by the platform via ONVIF. Remote search, playback, download, locking and unlocking of the record files, and support downloading files broken transfer resume. Remote parameters setup; remote import/export of device parameters. Remote viewing of the device status, system logs and alarm status. Remote locking and unlocking of mouse. Remote HDD initializing and program upgrading. Remote system restart and shutdown. Alarm and exception information can be sent to the remote host. Remotely start/stop recording. Remotely start/stop alarm output. Remote PTZ control. Two-way audio and voice broadcasting. Embedded WEB server. 7

8 Development Scalability: SDK for Windows and Linux system. Source code of application software for demo. Development support and training for application system. 8

9 TABLE OF CONTENTS Product Key Features... 6 Chapter 1 Introduction Front Panel IR Remote Control Operations USB Mouse Operation Input Method Description Rear Panel Chapter 2 Getting Started Starting Up and Shutting Down the NVR Using the Wizard for Basic Configuration Adding and Editing the IP Cameras Adding the Online IP Cameras Editing the Connected IP cameras and Configuring Customized Protocols Editing IP Cameras Connected to the PoE Interfaces Editing IP Cameras Connected to the Built-in Switch Network Interfaces Chapter 3 Live View Introduction of Live View Operations in Live View Mode Using the Mouse in Live View Quick Setting Toolbar in Live View Mode Adjusting Live View Settings User Logout Chapter 4 PTZ Controls Setting PTZ Presets, Patrols & Patterns Customizing Presets Calling Presets Customizing Patrols Calling Patrols Customizing Patterns Calling Patterns PTZ Control Toolbar Chapter 5 Record Settings Configuring Recording Parameters Configuring Record Schedule Configuring Motion Detection Record Configuring Alarm Triggered Record Manual Record Configuring Holiday Record Files Protection Chapter 6 Playback Playing Back Record Files

10 6.1.1 Playing Back by Channel Playing Back by Time Playing Back by Event Search Playing Back by Tag Playing Back by System Logs Playing Back External File Auxiliary Functions of Playback Playing Back Frame by Frame Digital Zoom Reverse Playback of Multi-channel Chapter 7 Backup Backing up Record Files Quick Export Backing up by Normal Video Search Backing up by Event Search Backing up Video Clips Managing Backup Devices Chapter 8 Alarm Settings Setting Motion Detection Alarm Setting Sensor Alarms Detecting Video Loss Alarm Detecting Video Tampering Alarm Handling Exceptions Alarm Setting Alarm Response Actions Triggering or Clearing Alarm Output Manually Chapter 9 Network Settings Configuring General Settings Configuring Advanced Settings Configuring PPPoE Settings Configuring WIFI Configuring DDNS Configuring NTP Server Configuring Remote Alarm Host Configuring Multicast Configuring RTSP Configuring Server and HTTP Ports Configuring Configuring UPnP Configuring High-speed Download Checking Network Traffic Configuring Network Detection Testing Network Delay and Packet Loss Exporting Network Packet Checking the Network Status

11 9.4.4 Checking Network Statistics Chapter 10 HDD Management Initializing HDDs Checking HDD Status HDD Detection Configuring HDD Error Alarms Chapter 11 Camera Settings Configuring OSD Settings Configuring Privacy Mask Configuring Image Parameters Chapter 12 NVR Management and Maintenance Viewing System Information Viewing Device Information Viewing Camera Information Viewing Record Information Viewing Alarm Information Viewing Network Information Viewing HDD Information Searching & Export Log Files Importing/Exporting Configuration Files Upgrading System Upgrading by Local Backup Device Upgrading by FTP Restoring Default Settings Chapter 13 Others Configuring General Settings Configuring DST Settings Configuring More Settings for Device Parameters Managing User Accounts Adding a User Deleting a User Editing a User Appendix Glossary Troubleshooting List of Compatible IP Cameras List of Hikvision IP Cameras List of Third-party IP Cameras

12 Chapter 1 Introduction 12

13 1.1 Front Panel Figure 1. 1 Front Panel of DS-7100NI Series This panel is applicable to the DS-7100NI-SL, DS-7100NI-SL/W, DS-7100NI-SN, DS-7100NI-SN/N and DS-7100NI-SN/P series NVR. Table 1. 1 Description of Front Panel No. Icon Description 1 Indicator turns red when DVR is powered up. 2 Indicator lights in red when data is being read from or written to HDD. 3 Indicator blinks blue when network connection is functioning properly. Figure 1. 2 Front Panel of DS-7600NI Series This panel is applicable to the DS-7600NI-SN, DS-7600NI-SN/N and DS-7600NI-SN/P series NVR. Table 1. 2 Description of Front Panel No. Name Description 1 Status Power Power indicator turns yellow when system is running. 13

14 No. Name Description Indicator Status indicator blinks red when data is being read from or written to Status HDD. TX/RX indictor blinks yellow when network connection is functioning Tx/Rx properly. 2 USB Interface Universal Serial Bus (USB) ports for additional devices such as USB mouse and USB Hard Disk Drive (HDD). 14

15 1.2 IR Remote Control Operations The NVR may also be controlled with the included IR remote control (not supported with theds-7100ni series NVR), shown in Figure Batteries (2 AAA) must be installed before operation. Figure 1. 3 Remote Control Table 1. 3 Description of the Soft Keyboard Icons No. Name Description 1 POWER Power on/off the device. 2 DEV Enables/Disables Remote Control. 3 Alphanumeric Buttons Switch to the corresponding channel in Live view or PTZ Control mode. Input numbers and characters in Edit mode. Switch between different channels in the Playback mode. 4 EDIT Button Edit text fields. When editing text fields, it will also function as a Backspace button to delete the character in front of the cursor. On checkbox fields, pressing the button will check the checkbox. In PTZ Control mode, the button adjusts the iris of the camera. 15

16 No. Name Description In Playback mode, it can be used to generate video clips for backup. Enter/exit the folder of USB device. 5 A Button Adjust focus in the PTZ Control menu. It is also used to switch between input methods (upper and lowercase alphabet, symbols and numeric input). 6 REC Button Enter the Manual Record setting menu. In PTZ control settings, press the button and then you can call a PTZ preset by pressing Numeric button. It is also used to turn audio on/off in the Playback mode. 7 PLAY Button The button is used to enter the All-day Playback mode. It is also used to auto scan in the PTZ Control menu. 8 INFO Button Reserved. 9 VOIP Button Switch between main and spot output. In PTZ Control mode, it can be used to zoom out the image. 10 MENU Button Press the button will help you return to the Main menu (after successful login). Press and hold the button for 5 seconds will turn off audible key beep. In PTZ Control mode, the MENU button will start wiper (if applicable). In Playback mode, it is used to show/hide the control interface. 11 PREV Button Switch between single screen and multi-screen mode. In PTZ Control mode, it is used to adjust the focus in conjunction with the A/FOCUS+ button. 12 DIRECTION Button Navigate between different fields and items in menus. In the Playback mode, the Up and Down button is used to speed up and slow down recorded video. The Left and Right button will select the next and previous record files. In Live View mode, these buttons can be used to cycle through channels. In PTZ control mode, it can control the movement of the PTZ camera. ENTER Button Confirm selection in any of the menu modes. It can also be used to tick checkbox fields. In Playback mode, it can be used to play or pause the video. In single-frame Playback mode, pressing the button will advance the video by a single frame. 13 PTZ Button In Auto-switch mode, it can be used to stop /start auto switch. 14 ESC Button Back to the previous menu. Press for Arming/disarming the device in Live View mode. 15 RESERVED Reserved for future usage. 16 F1 Button Select all items on the list when used in a list field. In PTZ Control mode, it will turn on/off PTZ light (if applicable). In Playback mode, it is used to switch between play and reverse play. 17 PTZ Control Buttons Buttons to adjust the iris, focus and zoom of a PTZ camera. 16

17 No. Name Description 18 F2 Button Cycle through tab pages. In synchronous playback mode, it is used to switch between channels. Troubleshooting Remote Control: Make sure you have installed batteries properly in the remote control. And you have to aim the remote control at the IR receiver in the front panel. If there is no response after you press any button on the remote, follow the procedure below to troubleshoot. 1. Go to Menu > Settings > General > More Settings by operating the front control panel or the mouse. 2. Check and remember NVR ID#. The default ID# is 255. This ID# is valid for all the IR remote controls. 3. Press the DEV button on the remote control. 4. Enter the NVR ID# you set in step Press the ENTER button on the remote. If the Status indicator on the front panel turns blue, the remote control is operating properly. If the Status indicator does not turn blue and there is still no response from the remote, please check the following: Batteries are installed correctly and the polarities of the batteries are not reversed. Batteries are fresh and not out of charge. IR receiver is not obstructed. If the remote still cannot function properly, please change a remote and try again, or contact the device provider. 17

18 1.3 USB Mouse Operation A regular 3-button (Left/Right/Scroll-wheel) USB mouse can also be used with this NVR. To use a USB mouse: 1. Plug USB mouse into one of the USB interfaces on the front panel of the NVR. 2. The mouse should automatically be detected. If in a rare case that the mouse is not detected, the possible reason may be that the two devices are not compatible, please refer to the recommended the device list from your provider. The operation of the mouse: Table 1. 4 Description of the Mouse Control Name Action Description Single-Click Live view: Select channel and show the quick set menu. Menu: Select and enter. Double-Click Live view: Switch between single-screen and multi-screen. Left-Click Click and Drag PTZ control: pan, tilt and zoom. Tamper-proof, privacy mask and motion detection: Select target area. Digital zoom-in: Drag and select target area. Live view: Drag channel/time bar. Right-Click Single-Click Live view: Show menu. Menu: Exit current menu to upper level menu. Scroll-Wheel Scrolling up Live view: Previous screen. Menu: Previous item. Scrolling down Live view: Next screen. Menu: Next item. 18

19 1.4 Input Method Description Figure 1. 4 Soft Keyboard Description of the buttons on the soft keyboard: Table 1. 5 Description of the Soft Keyboard Icons Icons Description Icons Description English Capital English Numbers Symbols Lowercase/Uppercase Backspace Space Enter Exit 19

20 1.5 Rear Panel Figure 1. 5 DS-7100NI-SL and DS-7100NI-SN Figure 1. 6 DS-7100NI-SL/W Table 1. 6 Description of Rear Panel No. Item Description 1 Power Supply 12VDC power supply. 2 Audio In RCA connector for two-way audio input. 3 HDMI Interface HDMI video output connector. 4 Network Interface Connector for LAN (Local Area Network). 5 Audio Out RCA connector for audio output. 6 VGA Output DB9 connector for VGA output. Display local video output and menu. 7 USB Interface Universal Serial Bus (USB) ports for additional devices such as USB mouse and USB Hard Disk Drive (HDD). 8 Ground Ground (needs to be connected when NVR starts up). Antenna Interface Needs to be connected with antenna if you want to configure and get 9 (for DS-7100NI-SL/W series NVR only) connection via WLAN. Figure 1. 7 DS-7104NI-SN/N 20

21 Figure 1. 8 DS-7108 & 7116NI-SN/N Table 1. 7 Description of Rear Panel No. Item Description 1 Power Supply 12VDC power supply. 2 Audio In RCA connector for two-way audio input. 3 HDMI Interface HDMI video output connector. 4 Network Interface Connector for LAN (Local Area Network). 5 Audio Out RCA connector for audio output. 6 VGA Output DB9 connector for VGA output. Display local video output and menu. 7 USB Interface Universal Serial Bus (USB) ports for additional devices such as USB mouse and USB Hard Disk Drive (HDD). 8 Ground Ground (needs to be connected when NVR starts up). 9 Network Interfaces with switch function Network interface for the cameras. Figure 1. 9 DS-7104NI-SN/P Figure DS-7108 & 7116NI-SN/P Table 1. 8 Description of Rear Panel No. Item Description 1 Power Supply 48VDC power supply. 2 Audio In RCA connector for two-way audio input. 3 HDMI Interface HDMI video output connector. 4 Network Interface Connector for LAN (Local Area Network). 5 Audio Out RCA connector for audio output. 21

22 No. Item Description 6 VGA Output DB9 connector for VGA output. Display local video output and menu. 7 USB Interface Universal Serial Bus (USB) ports for additional devices such as USB mouse and USB Hard Disk Drive (HDD). 8 Ground Ground (needs to be connected when NVR starts up). 9 Network Interfaces with PoE function Network interface for the cameras and to provide power over Ethernet. Figure DS-7600NI-SN Figure DS-7604NI-SN/N Figure DS-7608 & 7616NI-SN/N Table 1. 9 Description of Rear Panel No. Item Description 1 Power Supply 12VDC power supply. 2 Audio In RCA connector for two-way audio input. 3 HDMI Interface HDMI video output connector. 4 Network Interface Connector for LAN (Local Area Network). 5 Audio Out RCA connector for audio output. 6 VGA Output DB9 connector for VGA output. Display local video output and menu. 7 USB Interface Universal Serial Bus (USB) ports for additional devices such as USB mouse and USB Hard Disk Drive (HDD). 8 Ground Ground (needs to be connected when NVR starts up). 9 Power Switch Switch for turning on/off the device. Network Interfaces 10 with switch function (for DS-7600NI-SN/N) Network interface for the cameras. 22

23 Figure DS-7604NI-SN/P Figure DS-7608 & 7616NI-SN/P Table Description of Rear Panel No. Item Description 1 Power Supply 48VDC power supply for DS-7604NI-SN/P, and 100~240VAC power supply for DS-7608 & 7616NI-SN/P 2 Audio In RCA connector for two-way audio input. 3 HDMI Interface HDMI video output connector. 4 Network Interface Connector for LAN (Local Area Network). 5 Audio Out RCA connector for audio output. 6 VGA Output DB9 connector for VGA output. Display local video output and menu. 7 USB Interface Universal Serial Bus (USB) ports for additional devices such as USB mouse and USB Hard Disk Drive (HDD). 8 Ground Ground (needs to be connected when NVR starts up). 9 Power Switch Switch for turning on/off the device. 10 Network Interfaces with PoE function Network interface for the cameras and to provide power over Ethernet. 23

24 Chapter 2 Getting Started 24

25 2.1 Starting Up and Shutting Down the NVR Purpose: Proper startup and shutdown procedures are crucial to expanding the life of the NVR. Before you start: Check that the voltage of the extra power supply is the same with the NVR s requirement, and the ground connection is working properly. Starting up the NVR: 1. Check the power supply is plugged into an electrical outlet. It is HIGHLY recommended that an Uninterruptible Power Supply (UPS) be used in conjunction with the device. 2. After startup, the Power LED indicator blinks red. A splash screen with the status of the HDD appears on the monitor. Shutting down the NVR 1. Enter the Shutdown menu. Menu > Shutdown Figure 2. 1 Shutdown Menu 2. Click the Shutdown button. 3. Click the Yes button. 4. Unplug the power supply (for DS-7100NI series NVR) or turn off the power switch (for DS-7600NI series NVR) on the rear panel when the shutdown attention pops up. Figure 2. 2 Shutdown Attention Rebooting the NVR In the Shutdown menu, you can also reboot the NVR. 25

26 1. Enter the Shutdown menu by clicking Menu > Shutdown. 2. Click the Logout button to lock the NVR or the Reboot button to reboot the NVR. 26

27 2.2 Using the Wizard for Basic Configuration By default, the Setup Wizard starts once the NVR has loaded, as shown in Figure below. Figure 2. 3 Start Wizard Interface Operating the Setup Wizard: 1. The Setup Wizard can walk you through some important settings of the NVR. If you don t want to use the Setup Wizard at that moment, click the Exit button. You can also choose to use the Setup Wizard next time by leaving the Start wizard when the device starts? checkbox checked. 2. Click Next button on the Wizard window to enter the Login window, as shown in Figure Figure 2. 4 Login Window 3. Enter the admin password. By default, the password is To change the admin password, check the New Admin Password checkbox. Enter the new password and confirm the password in the given fields. 5. Click the Next button to enter the date and time settings window, as shown in Figure

28 Figure 2. 5 Date and Time Settings 6. After the time settings, click Next button which takes you to the Network Setup Wizard window, as shown in Figure DS-7100NI-SL, DS-7100NI-SN and DS-7600NI-SN DS-7100NI-SL/W 28

29 DS-7100NI-SN/P, DS-7100NI-SN/N, DS-7600NI-SN/P and DS-7600NI-SN/N Figure 2. 6 Network Configuration The DS-7100NI-SL/W series NVR supports LAN and WLAN connections. Both the parameters can be configured saparately by selecting the NIC type in the Select NIC drop-down list. 7. For DS-7100NI-SL/W series NVR only, clicking the Next button will guide you to the WIFI parameters configuration. Figure 2. 7 WIFI Configuration For detailed description of each parameter, please refer to the Chapter Configuring WIFI. 8. Click Next button takes you to the HDD Management window, shown in Figure

30 Figure 2. 8 HDD Management 9. To initialize the HDD, click the Init button. Initialization removes all the data saved in the HDD. 10. Click Next button to enter the Adding IP Camera interface. 11. Click Search to find online IP Camera. Select the IP camera to be added, and click the Add button. Figure 2. 9 Search for IP Cameras 12. Click Next button. Configure the recording for the searched IP Cameras. Figure Record Settings 13. Click Copy to copy the settings to other channels, as shown in Figure

31 Figure Copy Record Settings 14. Click OK to complete the startup Setup Wizard. 31

32 2.3 Adding and Editing the IP Cameras Adding the Online IP Cameras Purpose: The main function of the NVR is to connect the network cameras and record the video got from it. So before you can get a live view or record of the video, you should add the network cameras to the connection list of the device. Before you start: Ensure the network connection is valid and correct. For detailed checking and configuring of the network, please see Chapter Checking Network Traffic and Chapter Configuring Network Detection. OPTION 1: 1. Right-click the mouse when you in the live view mode to show the right-click menu. 2. Select Add IP Camera in the pop-up menu and select Auto or Manual on your demand. Figure Right-click Menu of Adding IP camera Auto The device will add the detected IP cameras or encoders automatically by the default user name and password of administrator. Figure Auto Adding IP camera Interface 32

33 If the user name and password is changed, the auto adding of IP camera will fail, you may add it manually. Manual 1) To add the online cameras in same network segment i. The detected online camera will be listed in the camera list, as shown in the figure below. Figure Manual Adding IP Camera Interface The added IP cameras are marked in the white color, while the ones have not been added are marked in yellow. For the DS-7100NI-SL/W series NVR, the wirelessly detected or added IP cameras will be displayed in the list as well. For the details of configuring WLAN and WIFI, please refer to Chapter 9.1 Configuring General Settings and Configuring WIFI. ii. Click the button to add the camera. Table 2. 1 Explanation of the icons: Icon Explanation Icon Explanation Edit basic parameters of the camera The camera is connected; you can click the icon to get the live view of the camera. The camera is connected. Delete the IP camera Add the detected IP camera. The camera is disconnected; you can click the icon to get the exception information of camera. Advanced settings of the camera. 2) To add other IP cameras: i. Click the Custom Add button to pop up the Add IP Camera (Custom) interface. 33

34 Figure Custom Adding IP Camera Interface ii. You can edit the IP address, protocol, management port, and other information of the IP camera to be added. iii. Click Add to add the camera. OPTION 2: 1. Enter the Camera Management interface. Menu> Camera> Camera Figure Main Menu 2. Click the button to add the camera. 3. Repeat the step 2) of manual adding of IP camera to add other IP cameras. 34

35 Figure IP Camera Management Interface 4. (For the encoders with multiple channels only) check the checkbox of Channel No. in the pop-up window, as shown in the following figure, and click OK to finish adding. Figure Selecting Multiple Channels Editing the Connected IP cameras and Configuring Customized Protocols Editing the Connected IP Camera Purpose: After the adding of the IP cameras, the basic information of the camera lists in the page, you can configure the setting of the IP cameras. 1. Click the icon to edit the parameters; you can edit the IP address, protocol and other parameters. 35

36 Figure Edit the Parameters 2. Click lick OK to save the settings and exit the editing interface. To edit advanced parameters: 1. Drag the horizontal scroll bar to the right side and click the icon. Figure Network Configuration of the Camera 2. You can edit the network information and the password of the camera. Figure Password Configuration of the Camera 36

37 3. Click Apply to save the settings and click OK to exit the interface. Configuring the customized protocols Purpose: To connect the network cameras which are not configured with the standard protocols, you can configure the customized protocols for them. 1. Click the Protocol button in the custom adding IP camera interface to enter the protocol management interface. Figure Protocol Management Interface There are 16 customized protocols provided in the system, you can edit the protocol name; and choose whether to enable the sub-stream. 2. Choose the protocol type of transmission and choose the transfer protocols. The protocol type and the transfer protocols must be supported by the connected network camera. After adding the customized protocols, you can see the protocol name is listed in the dropdown list, please refer to Figure Figure Protocol Setting 3. Choose the protocols you just added to validate the connection of the network camera. 37

38 2.3.3 Editing IP Cameras Connected to the PoE Interfaces This chapter is only applicable to the DS-7600NI-SN/P and DS-7100NI-SN/P series NVR. The PoE interfaces enables the NVR system to pass electrical power safely, along with data, on Ethernet cabling to the connected network cameras. The DS-7600NI-SN/P and DS-7100NI-SN/P series NVR provide up to 8 PoE interfaces which can connect to 8 network cameras directly; and if you disable the PoE interface, you can also connect to the online network cameras. And the PoE interface supports the Plug-and-Play function. Example: As for 7604NI-SN/P NVR, when you want to connect 1 online camera and connect 3 network cameras via PoE interfaces, you must disable 1 PoE interface in the Edit IP camera panel. To add cameras for NVR supporting PoE function: Before you start: Connect the network cameras via the PoE interfaces. 1. Enter the Camera Management interface. Menu> Camera> Camera You can see the connected cameras are listed. Figure Camera List The cameras connecting to the PoE interface cannot be deleted in this menu. 2. Click the button, and select the Adding Method in the drop-down list. Plug-and-Play: It means that the camera is connected to the PoE interface, so in this case, the parameters of the camera can t be edited. The IP address of the camera can only be edited in the Network Configuration interface, see Chapter 9.1 Configuring General Settings for detailed information. 38

39 Figure Edit IP Camera Interface - Plug-and-Play Manual: You can disable the PoE interface by selecting the manual while the current channel can be used as a normal channel and the parameters can also be edited. Figure Edit IP Camera Interface - Manual 3. Click the Apply button to finish adding Editing IP Cameras Connected to the Built-in Switch Network Interfaces This chapter is only applicable to the DS-7600NI-SN/N and DS-7100NI-SN/N series NVR. For DS-7600NI-SN/N and DS-7100NI-SN/N series NVR, the extra network interfaces provide a built-in switch with plug-and-play function. Example: As for DS-7608NI-SN/N NVR, when you want to connect 2 online cameras and connect 6 network cameras via built-in switch interfaces, you must disable 2 built-in switch interfaces in the Edit IP camera panel. To add cameras for NVR via built-in switch interfaces: Before you start: 39

40 Connect the network cameras via the built-in switch interfaces. 1. Enter the Camera Management interface. Menu> Camera> Camera You can see the connected cameras are listed. Figure Camera List The cameras connecting to the built-in switch interface cannot be deleted in this menu. 2. Click the button, and select the Adding Method in the drop-down list. Plug-and-Play: It means that the camera is connected to the built-in switch interface, so in this case, the parameters of the camera can t be edited. The IP address of the camera can only be edited in the Network Configuration interface, see Chapter 9.1 Configuring General Settings for detailed information. Figure Edit IP Camera Interface - Plug-and-Play Manual: You can disable the built-in switch interface by selecting the manual while the current channel can be used as a normal channel and the parameters can also be edited. 40

41 Figure Edit IP Camera Interface - Manual 3. Click the Apply button to finish adding. 41

42 Chapter 3 Live View 42

43 3.1 Introduction of Live View Live view shows you the video image getting from each camera in real time. The NVR automatically enters Live View mode when powered on. Live View Icons In the live view mode, there are icons at the right top of the screen for each channel, showing the status of the record and alarm in the channel, so that you can know whether the channel is recorded, or whether there are alarms occur as soon as possible. Icons Table 3. 1 Description of Live View Icons Description Alarm (video loss, tampering, motion detection or sensor alarm) Record (manual record, continuous record, motion detection or alarm triggered record) Alarm & Record 43

44 3.2 Operations in Live View Mode In live view mode, there are many functions provided. The functions are listed below. Single Screen: showing only one screen on the monitor. Multi-screen: showing multiple screens on the monitor simultaneously. Auto-switch: the screen is auto switched to the next one. And you must set the dwell time for each screen on the configuration menu before enabling the auto-switch. Menu>Configuration>Live View>General. Start Recording: continuous record and motion detection record are supported. Add IP Camera: the shortcut to add IP camera, manual and auto are selectable. Output Mode: select the output mode to Standard, Bright, Gentle or Vivid. Playback: playback the recorded videos for current day Using the Mouse in Live View Table 3. 2 Mouse Operation in Live View Name Menu Single Screen Multi-screen Previous Screen Next Screen Start/Stop Auto-switch Start Recording Add IP Camera Playback Output Mode Description Enter the main menu of the system by right clicking the mouse. Switch to the single full screen by choosing channel number from the dropdown list. Adjust the screen layout by choosing from the dropdown list. Switch to the previous screen. Switch to the next screen. Enable/disable the auto-switch of the screens. Start continuous recording or motion detection recording of all channels. Add IP camera, manual mode and auto mode are selectable. Enter the playback interface and start playing back the video of the selected channel immediately. Four modes of output supported, including Standard, Bright, Gentle and Vivid. The dwell time of the live view configuration must be set before using Start Auto-switch. 44

45 Figure 3. 1 Right-click Menu Quick Setting Toolbar in Live View Mode On the screen of each channel, there is a quick setting toolbar which shows when you single click the mouse in the corresponding screen. Figure 3. 2 Quick Setting Toolbar Table 3. 3 Description of Quick Setting Toolbar Icons Icons Description Icons Description Icons Description Enable/Disable Instant Playback Mute/Audio on / Manual Record / PTZ Control Digital Zoom Image Settings Live View Strategy Close Instant Playback only shows the record in last five minutes. If no record is found, it means there is no record during the last five minutes. Digital Zoom can zoom in the selected area to the full screen. You can click and draw to select the area to zoom in, as shown in Figure

46 Figure 3. 3 Digital Zoom Image Settings icon can be selected to enter the Image Settings menu. You can set the image parameters like brightness, contrast, saturation and hue. Figure 3. 4 Image Settings- Customize Live View Strategy can be selected to set strategy, including Real-time, Balanced, Fluency. Figure 3. 5 Live View Strategy 46

47 3.3 Adjusting Live View Settings Purpose: Live View settings can be customized according to different needs. You can configure the output interface, dwell time for screen to be shown, mute or turning on the audio, the screen number for each channel, etc. 1. Enter the Live View Settings interface. Menu> Configuration> Live View Figure 3. 6 Live View-General The settings available in this menu include: Video Output Interface: Designates the output to configure the settings for. Only VGA/HDMI is selectable by default. Live View Mode: Designates the display mode to be used for Live View. Dwell Time: The time in seconds to dwell between switching of channels when enabling auto-switch in Live View. Enable Audio Output: Enables/disables audio output for the selected video output. Event Output: Designates the output to show event video. Full Screen Monitoring Dwell Time: The time in seconds to show alarm event screen. 2. Setting Cameras Order Figure 3. 7 Live View- Camera Order To set the camera order: 1) Select a View mode in. 2) Select the small window, and double-click on the channel number to display the channel on the 47

48 window. You can click button to start live view for all the channels and click to stop all the live view. 3) Click the Apply button to save the setting. 48

49 3.4 User Logout Purpose: After logging out, the monitor turns to the live view mode and if you want to do some operation, you need to enter user name and password tog in again. 1. Enter the Shutdown menu. Menu>Shutdown Figure 3. 8 Shutdown 2. Click Logout. After you have logged out the system, menu operation on the screen is invalid. It is required to input a user name and password to unlock the system. 49

50 Chapter 4 PTZ Controls 50

51 4.1 Setting PTZ Presets, Patrols & Patterns Before you start: Please make sure that the presets, patrols and patterns should be supported by PTZ protocols Customizing Presets Purpose: Follow the steps to set the Preset location which you want the PTZ camera to point to when an event takes place. 1. Enter the PTZ Control interface. Menu>Camera>PTZ Figure 4. 1 PTZ- More Settings 2. Use the directional button to wheel the camera to the location where you want to set preset. 3. Click the round icon before Save Preset. 4. Click the preset number to save the preset. Repeat the steps 2-4 to save more presets. If the number of the presets you want to save is greater than 17, click [ ] and choose the available numbers. Figure 4. 2 More Presets Calling Presets Purpose: 51

52 This feature enables the camera to point to a specified position such as a window when an event takes place. Call preset in the PTZ setting interface: 1. Enter the PTZ Control interface. Menu>Camera>PTZ 2. Check the round icon of Call Preset. Figure 4. 3 PTZ- Call Preset 3. Choose the preset number. Call preset in live view mode: 1. Press the PTZ button on the front panel or click the PTZ Control icon in the quick setting bar to enter the PTZ setting menu in live view mode. Figure 4. 4 PTZ Toolbar 2. Choose Camera in the list on the menu. 3. Double click the preset in the Preset list to call it. 52

53 4.1.3 Customizing Patrols Purpose: Patrols can be set to move the PTZ to different key points and have it stay there for a set duration before moving on to the next key point. The key points are corresponding to the presets. The presets can be set following the steps above in Customizing Presets. 1. Enter the PTZ Control interface. Menu>Camera>PTZ 2. Select patrol number in the drop-down list of patrol. 3. Select the under Patrol option box to add key points for the patrol. Figure 4. 5 PTZ- Add Key Point 4. Configure key point parameters, such as the key point No., duration of staying for one key point and speed of patrol. The key point is corresponding to the preset. The Key Point No. determines the order at which the PTZ will follow while cycling through the patrol. The Duration refers to the time span to stay at the corresponding key point. The Speed defines the speed at which the PTZ will move from one key point to the next. Figure 4. 6 Key Point Configuration 5. Click OK to save the key point to the patrol. Repeat the above steps to add more key points. Click the icon to delete the corresponding key point, and click the trash icon to.delete all the key points. 53

54 Select a key point, then click or button to adjust the order of the key points. Figure 4. 7 Key Points Deletion Calling Patrols Purpose: Calling a patrol makes the PTZ to move according the predefined patrol path. Calling patrol in the PTZ setting interface: 1. In the PTZ setting interface. Menu> Camera> PTZ> More Settings 2. Select the patrol number, and then click to call the patrol. 3. Click to stop it. Calling patrol in live view mode: 1. Press PTZ control on the front panel or on the remote, or click PTZ Control icon on the quick setting toolbar, to show the PTZ control toolbar. 2. Choose Patrol on the control bar. 3. Double click the patrol or select the patrol and click to call it. 54

55 Figure 4. 8 PTZ Toolbar- Patrol Customizing Patterns Purpose: Patterns can be set by recording the movement of the PTZ. You can call the pattern to make the PTZ movement according to the predefined path. 1. Enter the PTZ Control interface. Menu>Camera>PTZ>More Settings 2. Choose pattern number in the option box. Figure 4. 9 PTZ- Pattern 3. Click and use your mouse to drag the image or click the eight directional buttons in the control box under the image to move the PTZ camera. The movement of the PTZ is recorded as the pattern. 4. Click to save the pattern. 55

56 4.1.6 Calling Patterns Purpose: Follow the procedure to move the PTZ camera according to the predefined patterns. Calling pattern in the PTZ setting interface 1. Enter the PTZ Control interface. Menu>Camera>PTZ>More Settings 2. Select the pattern number. 3. Click, then the PTZ moves according to the pattern. Click to stop it. Call pattern in live view mode 1. In the live view mode, press PTZ control on the front panel or on the remote control, or click PTZ Control icon on the quick setting toolbar. 2. And then choose Pattern on the control bar. 3. Double click the pattern or select the pattern and click to call it. Figure PTZ Toolbar- Pattern 56

57 4.2 PTZ Control Toolbar In the Live View mode, you can press the PTZ Control button on the front panel or on the remote control, or choose the PTZ Control icon to enter the PTZ toolbar. Figure PTZ Toolbar Table 4. 1 Description of the PTZ toolbar icons Icon Description Icon Description Icon Description Direction button and the auto-cycle button The speed of the PTZ movement 3D-Zoom Zoom+, Focus+, Iris+ Light on/off Image Centralization Zoom-, Focus-, Iris- Wiper on/off Preset Patrol Pattern Menu Previous item Next item Start pattern/patrol Stop the patrol or pattern movement Minimize windows Exit 57

58 Chapter 5 Record Settings 58

59 5.1 Configuring Recording Parameters Purpose: By configuring the recording parameters you can define the parameters which affect the image quality, such as the transmission stream type, the resolution and so on. Before you start: Make sure that the HDD has already been installed. If not, please install a HDD and initialize it. (Menu>HDD>General) Figure 5. 1 HDD- General 1. Enter the Record settings interface to configure the recording parameters: Menu>Record> Parameters Figure 5. 2 Recording Parameters 2. Parameters Setting for Recording 1) Select Record tab page to configure. You can configure the stream type, the resolution, and other parameters on your demand. Pre-record: The time you set to record before the scheduled time or event. For example, when an alarm triggered the recording at 10:00, if you set the pre-record time as 5 seconds, the camera records it at 9:59:55. Post-record: The time you set to record after the event or the scheduled time. For example, when an alarm triggered the recording ends at 11:00, if you set the post-record time as 5 seconds, it records till 11:00:05. Expired Time: The expired time is the longest time for a record file to be kept in the HDD, if the deadline is reached, the file will be deleted. You can set the expired time to 0, and then the file will not be deleted. The actual keeping time for the file should be determined by the capacity of the HDD. Record Audio: Check the checkbox to enable or disable audio recording. 59

60 2) Click Apply to save the settings. The parameters of Main Stream (Event) are read-only. 3. Parameters Settings for Sub-stream 1) Enter the Sub-stream tab page. Figure 5. 3 Sub-stream Parameters 2) Configure the parameters of the camera. 3) Click Apply to save the settings. 60

61 5.2 Configuring Record Schedule Purpose: Set the record schedule, and then the camera automatically starts/stops recording according to the configured schedule. 1. Enter the Record Schedule interface. Menu>Record>Schedule 2. Configure Record Schedule 1) Select Record Schedule. Figure 5. 4 Record Schedule 2) Choose the camera you want to configure. 3) Select the check box after the Enable Schedule item. 4) Click Edit button or click on the color icon under the edit button and draw the schedule line on the panel. Edit the schedule: I. In the message box, you can choose the day to which you want to set schedule. Figure 5. 5 Recording Schedule Interface II. You can click the button to set the accurate time of the schedule. To schedule an all-day recording, check the checkbox after the All Day item. 61

62 Figure 5. 6 Edit Schedule III. To arrange other schedule, leave the All Day checkbox blank and set the Start/End time. Up to 8 periods can be configured for each day. And the time periods can t be overlapped each other. Repeat the above edit schedule steps to schedule recording for other days in the week. If the schedule can also be applied to other days, click Copy. Figure 5. 7 Copy Schedule to Other Days IV. Click OK to save setting and back to upper level menu. V. Click Apply in the Record Schedule interface to save the settings. Draw the schedule: 1) Click on the color icons, you can choose the schedule type as continuous or event. Figure 5. 8 Draw the Schedule Descriptions of the color icons are shown in the figure below. 62

63 DS-7100NI-SL and DS-7100NI-SL/W Other models Figure 5. 9 Descriptions of the color icons 2) Click the Apply button to validate the settings. 3) (Optional) If the settings can also be used to other channels, click Copy, and then choose the channel to which you want to copy. Figure Copy Schedule to Other Channels 63

64 5.3 Configuring Motion Detection Record Purpose: Follow the steps to set the motion detection parameters. In the live view mode, once a motion detection event takes place, the NVR can analyze it and do many actions to handle it. Enabling motion detection function can trigger certain channels to start recording, or trigger full screen monitoring, audio warning, notify the surveillance center and so on. In this chapter, you can follow the steps to schedule a record which triggered by the detected motion. 1. Enter the Motion Detection interface. Menu>Camera>Motion Figure Motion Detection 2. Configure Motion Detection: 1) Choose camera you want to configure. 2) Check the checkbox after Enable Motion Detection. 3) Drag and draw the area for motion detection by mouse. If you want to set the motion detection for all the area shot by the camera, click Full Screen. To clear the motion detection area, click Clear. Figure Motion Detection- Mask 4) Click Setting, and the message box for channel information pop up. 64

65 Figure Motion Detection Setting 5) Select the channels which you want the motion detection event to trigger recording. 6) Click Apply to save the settings. 7) Click OK to back to the upper level menu. 8) Exit the Motion Detection menu. 3. Edit the Motion Detection Record Schedule. For the detailed information of schedule configuration, see Chapter Configuring Record Schedule. 65

66 5.4 Configuring Alarm Triggered Record This section is not supported by DS-7100N-SL and DS-7100NI-SL/W. For other models, the alarm input and output are not provided by default. But when the connected IP camera has alarm input and output, the alarm related record and playback are supported. Purpose: Follow the procedure to configure alarm triggered recording. 1. Enter the Alarm setting interface. Menu> Configuration> Alarm Figure Alarm Settings 2. Click the Alarm Input tab. Figure Alarm Settings- Alarm Input 1) Select Alarm Input number and configure alarm parameters. 2) Choose N.O (normally open) or N.C (normally closed) for alarm type. 3) Check the checkbox of Enable. 4) Click Settings. 66

67 Figure Alarm Settings 5) Choose the alarm triggered recording channel. 6) Check the checkbox to select channel. 7) Click Apply to save settings. 8) Click OK to back to the upper level menu. Repeat the above steps to configure other alarm input parameters. If the settings can also be applied to other alarm inputs, click Copy and choose the alarm input number. Figure Copy Alarm Input 3. Edit the Alarm triggered record in the Record Schedule setting interface. For the detailed information of schedule configuration, see Chapter Configuring Record Schedule. 67

68 5.5 Manual Record Purpose: Follow the steps to set parameters for the manual record. The manual recording is prior to the scheduled recording. 1. Enter the Manual settings interface. Menu> Manual Or press the REC button on the remote control. Figure Manual Record 2. Enabling Manual Record 1) Select Record on the left bar. 2) Click the status button before camera number to change to. 3. Disable manual record. Click the status button to change to. Green icon means that the channel is configured the record schedule. After rebooting all the manual records enabled are canceled. 68

69 5.6 Configuring Holiday Record Purpose: Follow the steps to configure the record schedule on holiday for that year. You may want to have different plan for recording on holiday. 1. Enter the Record setting interface. Menu>Record> Holiday Figure Holiday Settings 2. Enable Edit Holiday schedule. 1) Click to enter the Edit interface. Figure Edit Holiday Settings 2) Check the checkbox after Enable Holiday. 69

70 3) Select Mode from the dropdown list. There are three different modes for the date format to configure holiday schedule. 4) Set the start and end date. 5) Click Apply to save settings. 6) Click OK to exit the Edit interface. 3. Enter Record Schedule settings interface to edit the holiday recording schedule. See Chapter 5.2 Configuring Record Schedule. 70

71 5.7 Files Protection Purpose: You can lock the recorded files or set the HDD property to Read-only to protect the record files from being overwritten. 1. Enter Export setting interface. Menu> Export Figure Playback 2. Select the channels you want to investigate by checking the checkbox to. 3. Configure the record type, file type start/end time. 4. Click Search to show the results. Figure Playback- Search Result 5. Protect the record files. 1) Find the record files you want to protect, and then click the icon which will turn to, indicating that the file is locked. The record files of which the recording is still not completed cannot be locked. 2) Click to change it to to unlock the file and the file is not protected. 71

72 Figure Unlocking Attention 72

73 Chapter 6 Playback 73

74 6.1 Playing Back Record Files Playing Back by Channel Purpose: Play back the recorded video files of a specific channel in the live view mode. Channel switch is supported. Instant playback by channel Choose a channel in live view mode using the mouse and click the button in the quick setting toolbar. In the instant playback mode, only record files recorded during the last five minutes on this channel will be played back. Figure 6. 1 Instant Playback Interface Playback by channel 1. Enter the Playback interface. Right click a channel in live view mode and select Playback from the menu, as shown in Figure

75 Figure 6. 2 Right-click Menu under Live View Under multi-screen live view mode, the recorded files of the top-left channel will be played back. Pressing numerical buttons will switch playback to the corresponding channels during playback process. 2. Playback management. The toolbar in the bottom part of Playback interface can be used to control playing progress, as shown in Figure Figure 6. 3 Playback Interface Click the channel(s) to execute simultaneous playback of multiple channels. Figure 6. 4 Toolbar of Playback 75

76 The indicates the start/end time of the record. Table 6. 1 Detailed Explanation of Playback Toolbar Button Operation Button Operation Button Operation Button Operation / Audio on/ Start/Stop / Mute clipping 30s forward 30s reverse Add default Add Tag tag customized tag management Speed down / Pause reverse Pause play/ play/ Scaling Play/ Reverse play/ / / up/down the Single-frame Single-frame time line play reverse play Speed up Previous day Next day Full Screen Exit Stop Digital Zoom Video type Process bar Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to locate special frames Playing Back by Time Purpose: Play back video files recorded in specified time duration. Multi-channel simultaneous playback and channel switch are supported. 1. Enter playback interface. Menu>Playback 2. Check the checkbox of channel(s) in the channel list and then double-click to select a date on the calendar. Figure 6. 5 Playback Calendar If there are record files for that camera in that day, in the calendar, the icon for that day is displayed as. Otherwise it is displayed as 76

77 In the Playback interface: The toolbar in the bottom part of Playback interface can be used to control playing process, as shown in Figure Figure 6. 6 Interface of Playback by Time Figure 6. 7 Toolbar of Playback by Time The indicates the start/end time of the record. Table 6. 2 Detailed Explanation of Playback-by-time Interface Button Operation Button Operation Button Operation Button Operation / Audio on/ Start/Stop / Mute clipping 30s forward 30s reverse Add default Add Tag tag customized tag management Speed down / Pause reverse Pause play/ play/ Scaling Play/ Reverse play/ / / up/down the Single-frame Single-frame time line play reverse play Speed up Previous day Next day Full Screen Exit Stop Digital Zoom Video type Process bar Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to locate special frames. 77

78 6.1.3 Playing Back by Event Search Purpose: Play back record files on one or several channels searched out by restricting event type (e.g. motion detection). 1. Enter the Playback interface. Menu>Playback 2. Select the Event in the drop-down list on the top-left side. 3. Select Alarm Input (not supported by DS-7100NI-SL and DS-7100NI-SL/W) or Motion as the event type, and edit the Start time and End time. Figure 6. 8 Motion Search Interface 4. Click Search button to get the search result information. You may refer to the right-side bar for the result. Figure 6. 9 Search Result Bar 78

79 5. Click button to play back the file. You can click the Back button to back to the search interface. Pre-play and post-play can be configured. If the event is set to trigger the recording of multiple channels, clicking the will pop up the Synch Playback interface. You can select the channels to play back synchronously. Playback interface The toolbar in the bottom part of Playback interface can be used to control playing process. Figure Interface of Playback by Event Figure Toolbar of Playback by Event Table 6. 3 Detailed Explanation of Playback-by-event Toolbar Button Operation Button Operation Button Operation Button Operation / Audio on/ Mute / Start/Stop clipping 30s forward 30s reverse Add default tag Add customized tag Tag management Speed down / Pause reverse play/ Reverse play/ Single-frame reverse play / Pause play/ Play/ Single-frame play / Scaling up/down the time line Speed up Previous day Next day Full Screen Exit Stop Digital Zoom Process bar Video type 79

80 Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to locate special frames Playing Back by Tag Purpose: Video tag allows you to record related information like people and location of a certain time point during playback. You are also allowed to use video tag(s) to search for record files and position time point. Before playing back by tag: 1. Enter Playback interface. Menu>Playback 2. Search and play back the record file(s). Refer to Chapter for the detailed information about searching and playback of the record files. Figure Interface of Playback by Time Click Click button to add default tag. button to add customized tag and input tag name. Max. 64 tags can be added to a single video file. 3. Tag management. Click button to check, edit and delete tag(s). 80

81 Figure Tag Management Interface 1. Select the Tag from the drop-down list in the Playback interface. 2. Choose channels, edit start time and end time, and then click Search to enter Search Result interface. You can enter keyword in the textbox to search the tag on your command. Figure Video Search by Tag 3. Click button to play back the file. You can click the Back button to back to the search interface. Pre-play and post-play can be configured. 81

82 Figure Interface of Playback by Tag Figure Toolbar of Playback by Tag Table 6. 4 Detailed Explanation of Playback-by-tag Toolbar Button Operation Button Operation Button Operation Button Operation / Audio on/ Start/Stop / Mute clipping 30s forward 30s reverse Add default Add Tag tag customized tag management Speed down / Pause reverse Pause play/ play/ Scaling Play/ Reverse play/ / / up/down the Single-frame Single-frame time line play reverse play Speed up Previous day Next day Full Screen Exit Stop Digital Zoom Process bar Video type Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to locate special frames Playing Back by System Logs Purpose: Play back record file(s) associated with channels after searching system logs. 82

83 1. Enter Log Information interface. Menu>Maintenance>Log Information 2. Click Log Search tab to enter Playback by System Logs. Set search time and type and click Search button. Figure System Log Search Interface 3. Choose a log with record file and click button to enter Playback interface. If there is no record file at the time point of the log, the message box No result found will pop up. Figure Result of System Log Search 4. Playback interface. The toolbar in the bottom part of Playback interface can be used to control playing process. 83

84 Figure Interface of Playback by Log Playing Back External File Purpose: Perform the following steps to look up and play back files in the external devices. 1. Enter Tag Search interface. Menu>Playback 2. Select the External File in the drop-down list on the top-left side. The files are listed in the right-side list. You can click the button to refresh the file list. 3. Select and click the button to play back it. Figure Interface of External File Playback 84

85 6.2 Auxiliary Functions of Playback Playing Back Frame by Frame Purpose: Play video files frame by frame, in case of checking image details of the video when abnormal events happen. Go to Playback interface. If you choose playback of the record file: click button until the speed changes to Single frame and one click on the playback screen represents playback of one frame. If you choose adverse playback of the record file: click button until the speed changes to Single frame and one click on the playback screen represents adverse playback of one frame. It is also feasible to use button in toolbar Digital Zoom 1. Click the button on the playback control bar to enter Digital Zoom interface. 2. Use the mouse to draw a red rectangle and the image within it will be enlarged up to 16 times. Figure Draw Area for Digital Zoom 3. Right-click the image to exit the digital zoom interface Reverse Playback of Multi-channel Purpose: You can play back record files of multi-channel reversely. Up to 8-ch (with 4CIF resolution) simultaneous adverse 85

86 playback is supported; up to 4-ch (with 720P resolution) simultaneous adverse playback is supported, up to 2-ch (with 1080P resolution) and up to 1-ch (with 5MP resolution) reverse playback is supported. 1. Enter Playback interface. Menu>Playback 2. Check more than one checkboxes to select multiple channels and click to select a date on the calendar. Figure ch Synchronous Playback Interface 3. Click to play back the record files reversely. 86

87 Chapter 7 Backup 87

88 7.1 Backing up Record Files Quick Export Purpose: Export record files to backup device(s) quickly. 1. Enter Video Export interface. Menu>Export>Normal Choose the channel(s) you want to back up and click Quick Export button. The time duration of record files on a specified channel cannot exceed one day. Otherwise, the message box Max. 24 hours are allowed for quick export. will pop up. The number of channels for synchronous export cannot exceed 4. Otherwise, the message box Max. 4 channels are allowed for synchronous quick export. will pop up. Figure 7. 1 Quick Export Interface 1. Click the Export button to start exporting. Here we use USB Flash Drive and please refer to the next section Normal Backup for more backup devices supported by the device. Figure 7. 2 Quick Export using USB1-1 Stay in the Exporting interface until all record files are exported. 88

89 Figure 7. 3 Export Finished 2. Check backup result. Choose the record file in Export interface and click button to check it. The Player player.exe will be exported automatically during record file export. Figure 7. 4 Checkup of Quick Export Result Using USB Backing up by Normal Video Search Purpose: The record files can be backup to various devices, such as USB devices (USB flash drives, USB HDDs, USB writer), and SATA writer. Backup using USB flash drives and USB HDDs 1. Enter Export interface. Menu>Export>Normal 2. Set search condition and click Search button to enter the search result interface. 89

90 Figure 7. 5 Normal Video Search for Backup 3. Select record files you want to back up. Click to play the record file if you want to check it. Check the checkbox before the record files you want to back up. The size of the currently selected files is displayed in the lower-left corner of the window. Figure 7. 6 Result of Normal Video Search for Backup 4. Export. Click Export button and start backup. If the inserted USB device is not recognized: Click the Refresh button. Reconnect device. Check for compatibility from vendor. You can also format USB flash drives or USB HDDs via the device. 90

91 Figure 7. 7 Export by Normal Video Search using USB Flash Drive Stay in the Exporting interface until all record files are exported with pop-up message box Export finished. Figure 7. 8 Export Finished 5. Check backup result. Choose the record file in Export interface and click button to check it. The Player player.exe will be exported automatically during record file export. Figure 7. 9 Checkup of Export Result using USB Flash Drive 91

92 Backup using USB writer and SATA writer 1. Enter Export interface. Menu>Export>Normal 2. Set search condition and click Search button to enter the search result interface. Figure Normal Video Search for Backup 3. Select record files you want to back up. Click button to play the record file if you want to check it. Check the checkbox before the record files you want to back up. The size of the currently selected files is displayed in the lower-left corner of the window. Figure Result of Normal Video Search for Backup 4. Export. Click Export button and start backup. If the inserted USB writer or SATA writer is not recognized: Click the Refresh button. Reconnect device. Check for compatibility from vendor. 92

93 Figure Export by Normal Video Search using USB Writer Stay in the Exporting interface until all record files are exported with pop-up message box Export finished. Figure Export Finished 5. Check backup result. Choose the record file in Export interface and click button to check it. The Player player.exe will be exported automatically during record file export. Figure Checkup of Export Result using USB Writer 93

94 7.1.3 Backing up by Event Search Purpose: Back up event-related record files using USB devices (USB flash drives, USB HDDs, USB writer), or SATA writer. Quick Backup and Normal Backup are supported. 1. Enter Export interface. Menu>Export>Event 1) Set the searching time period. Event types contain Alarm Input and Motion, here we take the backing up by motion as an example. 1) Click Search button to enter the Search Result interface. Figure Event Search for Backup 2. Select record files to export. 1) Select a motion event in the list and click Quick Export button to enter Export interface immediately. 2) Clicking Details button will take you to the interface with detailed information of all channels triggered by the selected motion event. 3) Clicking Quick Export button will export record files of all channels triggered by the selected motion event. Figure Result of Event Search 4) Click Details button to view detailed information of the record file, e.g. start time, end time, file size, etc. 94

95 Figure Event Details Interface 3. Export. Click the Export button and start back up. If the inserted USB device is not recognized: Click the Refresh button. Reconnect device. Check for compatibility from vendor. You can also format USB flash drive or USB HDDs via the device. Figure Export by Event Using USB Flash Drive Stay in the Exporting interface until all record files are exported with pop-up message Export finished. Figure Export Finished 95

96 4. Check backup result. The Player player.exe will be exported automatically during record file export. Figure Checkup of Event Export Result Using USB Flash Drive Backing up Video Clips Purpose: You may also select video clips to export directly during Playback, using USB devices (USB flash drives, USB HDDs, USB writer) or SATA writer. 1. Enter Playback interface. Please refer to Chapter 6.1 Playing Back Record Files. 2. During playback, use buttons and in the playback toolbar to start or stop clipping record file(s). 3. Quit Playback interface after finishing clipping and you will then be prompted to save the clips. A maximum of 30 clips can be selected for each channel. 96

97 Figure Interface of Playback by Time 4. Click Yes to save video clips and enter Export interface, or click No to quit and do not save video clips. Figure Attention to Video Clip Saving 5. Export. Click Export button and start backup. If the inserted USB device is not recognized: Click the Refresh button. Reconnect device. Check for compatibility from vendor. You can also format USB flash drive or USB HDDs via the device. Figure Export Video Clips Using USB Flash Drive 97

98 Stay in the Exporting interface until all record files are exported with pop-up message Export finished. Figure Export Finished 6. Check backup result. The Player player.exe will be exported automatically during record file export. Figure Checkup of Video Clips Export Result Using USB Flash Drive 7.2 Managing Backup Devices Management of USB flash drives and USB HDDs. 1. Enter Search Result interface of record files. Menu>Export>Normal Set search condition and click Search button to enter Search Result interface. At least one channel shall be selected. 98

99 Figure Normal Video Search for Backup 2. Select record files you want to back up. Click Export button to enter Export interface. At least one record file shall be selected. Figure Result of Normal Video Search for Backup 3. Backup device management. Click New Folder button if you want to create a new folder in the backup device. Select a record file or folder in the backup device and click button if you want to delete it. Select a record file in the backup device and click button to play it. Click Format button to format the backup device. If the inserted USB device is not recognized: Click the Refresh button. Reconnect device. Check for compatibility from vendor. 99

100 Figure USB Flash Drive Management Management of USB writers or DVD-R/W 1. Enter Search Result interface of record files. Menu>Export>Normal Set search condition and click Search button to enter Search Result interface. At least one channel shall be selected. Figure Normal Video Search for Backup 2. Select record files you want to back up. Click Export button to enter Export interface. At least one record file shall be selected. 100

101 Figure Result of Normal Video Search for Backup 3. Backup device management. Click Erase button if you want to erase the files from a re-writable CD/DVD. There must be a re-writable CD/DVD when you make this operation. If the inserted USB writer or DVD-R/W is not recognized: Click the Refresh button. Reconnect device. Check for compatibility from vendor. Figure USB Writer Management 101

102 Chapter 8 Alarm Settings 102

103 8.1 Setting Motion Detection Alarm 1. Enter Motion Detection interface of Camera Management and choose a camera you want to set up motion detection. Menu> Camera> Motion Figure 8. 1 Motion Detection Setup Interface 2. Set up detection area and sensitivity. Tick Enable Motion Detection, use the mouse to draw detection area(s) and drag the sensitivity bar to set sensitivity. Click button and set alarm response actions. 3. Click Trigger Channel tab and select one or more channels which will start to record or become full-screen monitoring when motion alarm is triggered, and click Apply to save the settings. Figure 8. 2 Set Trigger Camera of Motion Detection 4. Set up arming schedule of the channel. 1) Select Arming Schedule tab to set the arming schedule of handling actions for the motion detection. 2) Choose one day of a week and up to eight time periods can be set within each day. 3) Click Apply to save the settings Time periods shall not be repeated or overlapped. 103

104 Figure 8. 3 Set Arming Schedule of Motion Detection 5. Click Linkage Action tab to set up alarm response actions of motion alarm (please refer to Chapter 8.6 Setting Alarm Response Actions). Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy button to copy an arming schedule to other days. 6. Click the OK button to complete the motion detection settings of the channel. 104

105 8.2 Setting Sensor Alarms This section is not supported by DS-7100NI-SL and DS-7100NI-SL/W. Purpose: Set parameters and handling action of an external sensor alarm. 1. Enter Alarm Settings of System Configuration and select an alarm input. Menu> Configuration> Alarm Select Alarm Input tab to enter Alarm Input Settings interface. Figure 8. 4 Alarm Status Interface of System Configuration 2. Set up the handling action of the selected alarm input. Check the Enable checkbox and click button to set up its alarm response actions. Figure 8. 5 Alarm Input Setup Interface 3. Select Trigger Channel tab and select one or more channels which will start to record or become full-screen monitoring when an external alarm is input. 4. Select Arming Schedule tab to set the channel s arming schedule. Choose one day of a week and Max. eight time periods can be set within each day. Time periods shall not be repeated or overlapped. 105

106 5. Select Linkage Action tab to set up alarm response actions of the alarm input (please refer to Chapter Setting Alarm Response Actions). Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy button to copy an arming schedule to other days. Figure 8. 6 Set Arming Schedule of Alarm Input 6. If necessary, select PTZ Linking tab and set PTZ linkage of the alarm input. Set PTZ linking parameters and click OK to complete the settings of the alarm input. Please check whether the PTZ or speed dome supports PTZ linkage. One alarm input can trigger presets, patrol or pattern of more than one channel. But presets, patrols and patterns are exclusive. Figure 8. 7 Set PTZ Linking of Alarm Input 7. If you want to set handling action of another alarm input, repeat the above steps or just copy the above settings to it. 106

107 Figure 8. 8 Copy Settings of Alarm Input 107

108 8.3 Detecting Video Loss Alarm Purpose: Detect video loss of a channel and take alarm response action(s). 1. Enter Video Loss interface of Camera Management and select a channel you want to detect. Menu> Camera> Video Loss Figure 8. 9 Video Loss Setup Interface 2. Set up handling method of video loss. Check the checkbox of Enable Video Loss Alarm, and click button to set up handling action of video loss. 3. Set up arming schedule of the channel. 1) Select Arming Schedule tab to set the channel s arming schedule. 2) Choose one day of a week and up to eight time periods can be set within each day. 3) Click Apply button to save the settings. Time periods shall not be repeated or overlapped. Figure Set Arming Schedule of Video Loss 4. Select Linkage Action tab to set up alarm response action of video loss (please refer to Chapter8.6 Setting Alarm Response Actions). 108

109 Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy button to copy an arming schedule to other days. 5. Click the OK button to complete the video loss settings of the channel. 109

110 8.4 Detecting Video Tampering Alarm Purpose: Trigger alarm when the lens is covered and take alarm response action(s). 1. Enter Video Tampering interface of Camera Management and select a channel you want to detect video tampering. Menu> Camera> Tamper-proof Figure Tamper-proof Setup Interface 2. Set the video tampering handling method of the channel. Check the checkbox of Enable Tamper-proof. Drag the sensitivity bar and choose a proper sensitivity level. Use the mouse to draw an area you want to detect video tampering. Click button to set handling method of video tampering. Figure Set Detection Area and Sensitivity of Video Tampering 3. Set arming schedule and alarm response actions of the channel. 1) Click Arming Schedule tab to set the channel s arming schedule. 2) Choose one day of a week and Max. eight time periods can be set within each day. 3) Click Apply button to save the settings. Time periods shall not be repeated or overlapped. 110

111 Figure Set Arming Schedule of Video Tampering 4. Select Linkage Action tab to set up alarm response actions of video tampering alarm (please refer to Chapter 8.6 Setting Alarm Response Actions). Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy button to copy an arming schedule to other days. 5. Click the OK button to complete the video tampering settings of the channel. 111

112 8.5 Handling Exceptions Alarm Purpose: Exception settings refer to the handling method of various exceptions, e.g. HDD Full: The HDD is full. HDD Error: Writing HDD error or unformatted HDD. Network Disconnected: Disconnected network cable. IP Conflicted: Duplicated IP address. Illegal Login: Incorrect user ID or password. Record Exception: No space for saving recorded files. Enter Exception interface of System Configuration and handle various exceptions. Menu> Configuration> Exceptions Please refer to Chapter 8.6 Setting Alarm Response Actions for detailed alarm response actions. DS-7100NI-SL and DS-7100NI-SL/W Other Models Figure Exceptions Setup Interface 112

113 8.6 Setting Alarm Response Actions Purpose: Alarm response actions will be activated when an alarm or exception occurs, including Full Screen Monitoring, Audible Warning (buzzer), Notify Surveillance Center, Trigger Alarm Output and Send . Full Screen Monitoring When an alarm is triggered, the local monitor (VGA or HDMI monitor) display in full screen the video image from the alarming channel configured for full screen monitoring. If alarms are triggered simultaneously in several channels, their full-screen images will be switched at an interval of 10 seconds (default dwell time). A different dwell time can be set by going to Menu >Configuration>Live View, and set the value of Full Screen Monitoring Dwell Time. Auto-switch will terminate once the alarm stops and you will be taken back to the Live View interface. You must select during Trigger Channel settings the channel(s) you want to make full screen monitoring. Audible Warning Trigger an audible beep when an alarm is detected. Notify Surveillance Center Sends an exception or alarm signal to remote alarm host when an event occurs. The alarm host refers to the PC installed with Remote Client. The alarm signal will be transmitted automatically at detection mode when remote alarm host is configured. Please refer to Chapter Configuring Remote Alarm Host for details of alarm host configuration. Linkage Send an with alarm information to a user or users when an alarm is detected. Please refer to Chapter Configuring for details of configuration. Trigger Alarm Output This function is not supported by DS-7100NI-SL and DS-710NI-SL/W. 1. Enter Alarm Output interface. Menu> Configuration> Alarm> Alarm Output Select an alarm output and set alarm name and dwell time. Click Schedule button to set the arming schedule of alarm output. 113

114 If Manually Clear is selected in the dropdown list of Dwell Time, you can clear it only by going to Menu> Manual> Alarm. Figure Alarm Output Setup Interface 2. Set up arming schedule of the alarm output. Choose one day of a week and up to 8 time periods can be set within each day. Time periods shall not be repeated or overlapped. Figure Set Arming Schedule of Alarm Output 3. Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy button to copy an arming schedule to other days. Click the OK button to complete the video tampering settings of the alarm output No. 4. You can also copy the above settings to another channel. Figure Copy Settings of Alarm Output 114

115 8.7 Triggering or Clearing Alarm Output Manually This section is not supported by DS-7100NI-SL and DS-710NI-SL/W. Purpose: Sensor alarm can be triggered or cleared manually. If Manually Clear is selected in the dropdown list of dwell time of an alarm output, the alarm can be cleared only by clicking Clear button in the following interface. Select the alarm output you want to trigger or clear and make related operations. Menu> Manual> Alarm Click Trigger/Clear button if you want to trigger or clear an alarm output. Click Trigger All button if you want to trigger all alarm outputs. Click Clear All button if you want to clear all alarm output. Figure Clear or Trigger Alarm Output Manually 115

116 Chapter 9 Network Settings 116

117 9.1 Configuring General Settings Purpose: Network settings must be properly configured before you operate NVR over network. 1. Enter the Network Settings interface. Menu >Configuration>Network 2. Select the General tab. DS-7100NI-SL, DS-7100NI-SN and DS-7600NI-SN DS-7100NI-SL/W DS-7100NI-SN/N, DS-7100NI-SN/P, DS-7600NI-SN/N and DS-7600NI-SN/P Figure 9. 1 Network Settings Interface 117

118 3. In the General Settings interface, you can configure the following settings: NIC Type, IPv4 Address, IPv4 Gateway, MTU, DNS Server and Default Route. The DS-7100NI-SL/W series NVR supports the wireless AP function, which means it can connect with the wireless IP camera via WLAN. To set the WLAN, select WLAN in the Select NIC drop-down list, and then configure the general parameters. It s highly recommended to set the LAN as the Default Route, or network may be disconnected. For the DS-7100NI-SN/N, DS-7100NI-SN/P, DS-7600NI-SN/N and DS-7600NI-SN/P series NVR, you need to configure the internal NIC address, so that IP addresses are assigned to the cameras connected to the PoE or built-in switch interfaces. The valid value range of MTU is 500 ~ If the DHCP server is available, you can click the checkbox of DHCP to automatically obtain an IP address and other network settings from that server. 4. After configuring the general settings, click Apply to save the settings. 118

119 9.2 Configuring Advanced Settings Configuring PPPoE Settings Purpose: Your NVR also allows access by Point-to-Point Protocol over Ethernet (PPPoE). 1. Enter the Network Settings interface. Menu >Configuration> Network 2. Select the PPPoE tab to enter the PPPoE Settings interface, as shown in Figure Figure 9. 2 PPPoE Settings Interface 3. Check the PPPoE checkbox to enable this feature. 4. Enter User Name and Password for PPPoE access. The User Name and Password should be assigned by your ISP. 5. Click Apply to save and exit the interface. 6. After successful settings, the system asks you to reboot the device to enable the new settings, and the PPPoE dial-up is automatically connected after reboot. You can go to Menu >Maintenance>System Info >Network interface to view the status of PPPoE connection. Please refer to Chapter 12.1 Viewing System Information for PPPoE status Configuring WIFI This section is only supported by DS-7100NI-SL/W series NVR. Purpose: After setting the WLAN parameters, you may set the WIFI parameters to activate the WIFI function. You can both get access to the NVR and add wireless IP camera to the NVR via the WIFI. Setting the WIFI 1. Enter the Network Settings interface. Menu >Configuration> Network 2. Click the WIFI tab to enter WIFI settings interface, as shown in the Figure

120 Figure 9. 3 WIFI Settings Interface 3. Configure the following parameters: SSID: SSID is short for Service Set Identifier, and it is displayed as the WIFI name when you search the available WIFI hotspots via other devices with WLAN function. Fill in the blank of SSID on your demand with any characters or numbers. The SSID can contain any character, and the length of it should be no longer than 32. Work Channel: Select the work channel for WIFI. And each channel stands for its own work frequency. The work channel is set as autoselect by default. Security Type: The security is for the WIFI access, if other people want to get access to the WIFI, they have to input the correct password which is configured by you. You can choose to disable the WIFI security, or three types of security are selectable: WPA PSK, WPA2 PSK and WPAPSK WPA2PSK. Encrypt Mode: If the selected Security Type is not Disable, please select the encrypt type in the corresponding drop-down list; there re TKIP, AES and TKIP_AES selectable. Encrypt Key: Set the WIFI password in the text filed. The Encrypt Key can contain any character, and the length of it should be in the range of 8 to 64. DHCP Start-Stop: If the DHCP of a device which connects to the WIFI is enabled, the NVR will allocate the IP address in the configured range to it automatically. 4. Click Apply to finish the settings. After the WIFI settings take effect, the NVR can automatically detect the available wireless IP cameras. And the detected cameras will be displayed in the IP camera list (Menu > Camera), and then you can add it as the normal IP camera. Additionally, the IP camera from our manufacture which is used for the first time can be connected directly by the NVR once it powers on. And in the lower part of the WIFI setting interface, you can see the list of wirelessly connected devices. 120

121 Updating the Firmware 1. Save the upgrade file in a USB storage device and connect it to the NVR. 2. Click the Update button and select the upgrade file in the pop-up USB device file list. You can see the current version of the WIFI firmware on the bottom of the pop-up window. Figure 9. 4 USB Device Interface 3. Click the Upgrade button to start upgrading Configuring DDNS Purpose: If your NVR is set to use PPPoE as its default network connection, you may set Dynamic DNS (DDNS) to be used for network access. Prior registration with your ISP is required before configuring the system to use DDNS. 1. Enter the Network Settings interface. Menu >Configuration> Network 2. Select the DDNS tab to enter the DDNS Settings interface, as shown in Figure Figure 9. 5 DDNS Settings Interface 3. Check the DDNS checkbox to enable this feature. 4. Select DDNS Type. Five different DDNS types are selectable: IPServer, DynDNS, PeanutHull, NO-IP and HiDDNS. IPServer: Enter Server Address for IPServer. 121

122 Figure 9. 6 IPServer Settings Interface DynDNS: 1) Input Server Address for DynDNS (i.e. members.dyndns.org). 2) In the NVR Domain Name text field, enter the domain obtained from the DynDNS website. 3) Enter the User Name and Password registered in the DynDNS website. Figure 9. 7 DynDNS Settings Interface PeanutHull: Enter the User Name and Password obtained from the PeanutHull website. Figure 9. 8 PeanutHull Settings Interface NO-IP: Enter the account information in the corresponding fields. Refer to the DynDNS settings. 1) Enter Server Address for NO-IP. 2) In the NVR Domain Name text field, enter the domain obtained from the NO-IP website (www.no-ip.com). 3) Enter the User Name and Password registered in the NO-IP website. Figure 9. 9 NO-IP Settings Interface HiDDNS: 122

123 Enter the Server Address and Device Domain Name for HiDDNS. 1) The Server Address of the HiDDNS server displays as by default. 2) Enter the Device Domain Name. You can use the alias you registered in the HiDDNS server or define a new device domain name. If a new alias of the device domain name is defined in the NVR, it will replace the old one registered on the server. You can register the alias of the device domain name in the HiDDNS server first and then enter the alias to the Device Domain Name in the NVR; you can also enter the domain name directly on the NVR to create a new one. Figure HiDDNS Settings Interface Register the device on the HiDDNS server. i. Go to the HiDDNS website: ii. Click to register an account if you do not have one and use the account to log in. Figure Register an Account iii. In the Device Management interface, click to register the device. Figure Register the Device The device name can only contain the lower-case English letter, numeric and - ; and it 123

124 must start with the lower-case English letter and cannot end with -. Access the Device via Web Browser or Client Software After having successfully registered the device on the HiDDNS server, you can access your device via web browser or Client Software with the Device Domain Name (Device Name). OPTION 1: Access the Device via Web Browser Open a web browser, and enter in the address bar. Alias refers to the Device Domain Name on the device or the Device Name on the HiDDNS server. Example: If you mapped the HTTP port on your router and changed it to port No. except 80, you have to enter port in the address bar to access the device. You can refer to Chapter for the mapped HTTP port No.. OPTION 2: Access the Devices via ivms4200 For ivms-4200, in the Add Device window, select and then edit the device information. Nickname: Edit a name for the device as you want. Server Address: Device Domain Name: It refers to the Device Domain Name on the device or the Device Name on the HiDDNS server you created. User Name: Enter the user name of the device. By default it is admin. Password: Enter the password of the device. By default it is Figure Access Device via ivms Click Apply button to save and exit the interface Configuring NTP Server Purpose: A Network Time Protocol (NTP) Server can be configured on your NVR to ensure the accuracy of system date/time. 1. Enter the Network Settings interface. Menu >Configuration> Network 124

125 2. Select the NTP tab to enter the NTP Settings interface, as shown in Figure Figure NTP Settings Interface 3. Check the Enable NTP checkbox to enable this feature. 4. Configure the following NTP settings: Interval: Time interval between the two synchronizing actions with NTP server. The unit is minute. NTP Server: IP address of NTP server. NTP Port: Port of NTP server. 5. Click Apply button to save and exit the interface. The time synchronization interval can be set from1 to 10080min, and the default value is 60min. If the NVR is connected to a public network, you should use a NTP server that has a time synchronization function, such as the server at the National Time Center (IP Address: ). If the NVR is setup in a more customized network, NTP software can be used to establish a NTP server used for time synchronization Configuring Remote Alarm Host Purpose: With a remote alarm host configured, the NVR will send the alarm event or exception message to the host when an alarm is triggered. The remote alarm host must have the Network Video Surveillance software installed. 1. Enter the Network Settings interface. Menu >Configuration> Network 2. Select the More Settings tab to enter the More Settings interface, as shown in Figure Figure More Settings Interface 3. Enter Alarm Host IP and Alarm Host Port in the text fields. The Alarm Host IP refers to the IP address of the remote PC on which the Network Video Surveillance Software (e.g., ivms-4200) is installed, and the Alarm Host Port must be the same as the alarm monitoring port configured in the software. Figure Configure Alarm Host 125

126 4. Click Apply button to save and exit the interface Configuring Multicast Purpose: The multicast can be configured to realize live view for more than 128 connections through network for the device. A multicast address spans the Class-D IP range of to It is recommended to use the IP address ranging from to Enter the Network Settings interface. Menu >Configuration> Network 2. Select the More Settings tab to enter the More Settings interface, as shown in Figure Set Multicast IP, as shown in Figure When adding a device to the Network Video Surveillance Software, the multicast address must be the same as the NVR s multicast IP. Figure Configure Multicast 4. Click Apply button to save and exit the interface. The multicast function should be supported by the network switch to which the NVR is connected Configuring RTSP Purpose: The RTSP (Real Time Streaming Protocol) is a network control protocol designed for use in entertainment and communications systems to control streaming media servers. 1. Enter the Network Settings menu Menu >Configuration> Network 2. Select the More Settings tab to enter the More Settings menu, as shown in Figure Figure RTSP Settings Interface 3. Enter the RTSP port in the text field of RTSP Service Port. The default RTSP port is 554, and you can change it according to different requirements. 4. Click Apply button to save and exit the menu. 126

127 9.2.8 Configuring Server and HTTP Ports Purpose: You can change the server and HTTP ports in the Network Settings menu. The default server port is 8000 and the default HTTP port is Enter the Network Settings interface. Menu >Configuration> Network 2. Select the More Settings tab to enter the More Settings interface, as shown in Figure Enter new Server Port and HTTP Port. Figure Host/Others Settings Menu 4. Enter the Server Port and HTTP Port in the text fields. The default Server Port is 8000 and the HTTP Port is 80, and you can change them according to different requirements. 5. Click Apply button to save and exit the interface. The Server Port should be set to the range of and it is used for remote client software access. The HTTP port is used for remote web access Configuring Purpose: The system can be configured to send an notification to all designated users if an alarm event is detected, etc., an alarm or motion event is detected or the administrator password is changed. Before configuring the settings, the NVR must be connected to a local area network (LAN) that maintains an SMTP mail server. The network must also be connected to either an intranet or the Internet depending on the location of the accounts to which you want to send notification. 1. Enter the Network Settings interface. Menu >Configuration> Network 2. Set the IPv4 Address, IPv4 Subnet Mask, IPv4 Gateway and the Preferred DNS Server in the Network Settings menu. 3. Click Apply button to save the settings. 4. Select the tab to enter the Settings interface. 127

128 Figure Settings Interface 5. Configure the following settings: Enable Server Authentication (optional): Check the checkbox to enable the server authentication feature. User Name: The user account of sender s for SMTP server authentication. Password: The password of sender s for SMTP server authentication. SMTP Server: The SMTP Server IP address or host name (e.g., smtp.263xmail.com). SMTP Port No.: The SMTP port. The default TCP/IP port used for SMTP is 25. Sender: The name of sender. Sender s Address: The address of sender. Select Receivers: Select the receiver. Up to 3 receivers can be configured. Receiver: The name of user to be notified. Receiver s Address: The address of user to be notified. Enable Attached Picture (optional): Check the checkbox of Enable Attached Picture if you want to send with attached alarm images. The interval is the time of two adjacent alarm images. You can also set SMTP port and enable SSL here. Interval: The interval refers to the time between two actions of sending attached pictures. Test: Sends a test message to verify that the SMTP server can be reached. 6. Click Apply button to save the settings. 7. You can click Test button to test whether your settings work. The corresponding Attention message box will pop up. Figure Testing Attention Configuring UPnP Purpose: Universal Plug and Play (UPnP ) can permit the device seamlessly discover the presence of other network 128

129 devices on the network and establish functional network services for data sharing, communications, etc. You can use the UPnP function to enable the fast connection of the device to the WAN via a router without port mapping. Before you start: If you want to enable the UPnP function of the device, you must enable the UPnP function of the router to which your device is connected. When the network working mode of the device is set as multi-address, the Default Route of the device should be in the same network segment as that of the LAN IP address of the router. 1. Enter the Network Settings interface. Menu > Configuration > Network 2. Select the UPnP tab to enter the UPnP interface. Figure UPnP Settings Interface 3. Check checkbox to enable UPnP. 4. Select the Mapping Type as Manual or Auto in the drop-down list. OPTION 1: Auto If you select Auto, the Port Mapping items are read-only, and the external ports are set by the router automatically. 1) Click Apply button to save the settings. 2) You can click Refresh button to get the latest status of the port mapping. Figure UPnP Settings Finished-Auto OPTION 2: Manual If you select Manual as the mapping type, you can edit the external port on your demand by clicking to activate the External Port Settings dialog box. 1) Click to activate the External Port Settings dialog box. Configure the external port No. for server port, http port, and RTSP port respectively. 129

130 You can use the default port No., or change it according to actual requirements. External Port indicates the port No. for port mapping in the router. The value of the RTSP port No. should be 554 or between 1024 and 65535, while the value of the other ports should be between 1 and and the value must be different from each other. If multiple devices are configured for the UPnP settings under the same router, the value of the port No. for each device should be unique. Figure External Port Settings Dialog Box 2) Click Apply button to save the settings. 3) You can click Refresh button to get the latest status of the port mapping. Figure UPnP Settings Finished-Manual Configuring High-speed Download This function is supported by DS-7100NI-SL and DS-7100NI-SL/W. Purpose: You can enable the High-speed Download function to widen the outgoing bandwidth of the device. In this way you can speed up the download of record files through web browser or CMS software. If you enable the high-speed download function, the local menu operation will get stuck. It is recommended to disable this function after finishing the remote downloading of record files. 1. Enter the Network Settings interface. Menu >Configuration> Network 130

131 2. Select the More Settings tab to enter the More Settings interface, as shown in Figure Check the checkbox of Enable High-speed Download. And click the OK button in the pop-up message box to confirm the settings. Figure High-speed Download Settings Menu Figure Message Box of High-speed Download 4. Click Apply button to save and exit the interface. 131

132 9.3 Checking Network Traffic Purpose: You can check the network traffic to obtain real-time information of NVR such as linking status, MTU, sending/receiving rate, etc. 1. Enter the Network Traffic interface. Menu >Maintenance>Net Detect Figure Network Traffic Interface 2. You can view the sending rate and receiving rate information on the interface. The traffic data is refreshed every 1 second. 132

133 9.4 Configuring Network Detection Purpose: You can obtain network connecting status of NVR through the network detection function, including network delay, packet loss, etc Testing Network Delay and Packet Loss 1. Enter the Network Traffic interface. Menu >Maintenance>Net Detect 2. Click the Network Detection tab to enter the Network Detection menu, as shown in Figure Figure Network Detection Interface 3. Enter the destination address in the text field of Destination Address. 4. Click Test to start testing network delay and packet loss. The testing result pops up on the window. If the testing is failed, the error message box will pop up as well. Refer to Figure Figure Testing Result of Network Delay and Packet Loss Exporting Network Packet Purpose: By connecting the NVR to network, the captured network data packet can be exported to USB-flash disk and other local backup devices. 1. Enter the Network Traffic interface. Menu >Maintenance>Net Detect 2. Click the Network Detection tab to enter the Network Detection interface. 3. Select the backup device from the dropdown list of Device Name, as shown in Figure

134 Click Refresh button if the connected local backup device cannot be displayed. When it fails to detect the backup device, please check whether it is compatible with the NVR. You can format the backup device if the format is incorrect. DS-7100NI-SL/W Other Models Figure Export Network Packet 4. Click Export to start exporting. For the DS-7100NI-SL/W series NVR, the network packages of WLAN and LAN can be exported separately. 5. After the exporting is complete, click OK to finish the packet export. Figure Packet Export Attention Up to 1M data can be exported each time Checking the Network Status Purpose: You can also check the network status and quick set the network parameters in this interface. 134

135 Click Status button on the right bottom of the page. Figure Network status checking If the network is normal the following message box pops out. Figure Network status checking result If the message box pops out with other information instead of this one, you can click Network button to show the quick setting interface of the network parameters Checking Network Statistics Purpose: You can check the network status to obtain the real-time information of NVR. 1. Enter the Network Detection interface. Menu>Maintenance>Net Detect 2. Choose the Network Stat. tab. 135

136 Figure Network Stat. Interface 3. Check the bandwidth of IP Camera, bandwidth of Remote Live View, bandwidth of Remote Playback, bandwidth of Net Receive Idle and bandwidth of Net Send Idle. 4. You can click Refresh button to get the newest status. 136

137 Chapter 10 HDD Management 137

138 10.1 Initializing HDDs Purpose: A newly installed hard disk drive (HDD) must be initialized before it can be used with your NVR. A message box pops up when the NVR starts up if there exits any uninitialized HDD. Figure Message Box of Uninitialized HDD Click Yes button to initialize it immediately or you can perform the following steps to initialize the HDD. 1. Enter the HDD Information interface. Menu > HDD> General Figure HDD Information Interface 2. Select HDD to be initialized. 3. Click the Init button. Figure Confirm Initialization 4. Select the OK button to start initialization. Figure Status changes to Formatting 5. After the HDD has been initialized, the status of the HDD will change from Uninitialized to Normal. 138

139 Figure HDD Status Changes to Normal Initializing the HDD will erase all data on it. 139

140 10.2 Checking HDD Status Purpose: You may check the status of the installed HDDs on NVR so as to take immediate check and maintenance in case of HDD failure. Checking HDD Status in HDD Information Interface 1. Enter the HDD Information interface. Menu > HDD>General 2. Check the status of each HDD which is displayed on the list, as shown in Figure Figure View HDD Status (1) If the status of HDD is Normal or Sleeping, it works normally. If the status is Uninitialized or Abnormal, please initialize the HDD before use. And if the HDD initialization is failed, please replace it with a new one. Checking HDD Status in HDD Information Interface 1. Enter the System Information interface. Menu >Maintenance > System Info 2. Click the HDD tab to view the status of each HDD displayed on the list, as shown in Figure

141 Figure View HDD Status (2) 141

142 10.3 HDD Detection Purpose: The device provides the HDD detection function such as the adopting of the S.M.A.R.T. and the Bad Sector Detection technique. The S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitoring system for HDD to detect and report on various indicators of reliability in the hopes of anticipating failures. S.M.A.R.T. Settings 1. Enter the S.M.A.R.T Settings interface. Menu > HDD > HDD Detect 2. Select the HDD to view its S.M.A.R.T information list, as shown in Figure Figure S.M.A.R.T Settings Interface The related information of the S.M.A.R.T. is shown on the interface. You can choose the self-test types as Short Test, Expanded Test or the Conveyance Test. Click the button to start the S.M.A.R.T. HDD self-evaluation. If you want to use the HDD even when the S.M.A.R.T. checking is failed, you can check the checkbox of the Continue to use the disk when self-evaluation is failed item. Bad Sector Detection 1. Click the Bad Sector Detection tab. 2. Select the HDD No. in the dropdown list you want to configure, and choose All Detection or Key Area Detection as the detection type. 3. Click the Detect button to start the detection 142

143 Figure Bad Sector Detection And you can click Error info button to see the detailed damage information And you can also pause/resume or cancel the detection. 143

144 10.4 Configuring HDD Error Alarms Purpose: You can configure the HDD error alarms when the HDD status is Uninitialized or Abnormal. 1. Enter the Exception interface. Menu > Configuration > Exceptions 2. Select the Exception Type to HDD Error from the dropdown list. 3. Click the checkbox(s) below to select the HDD error alarm type (s), as shown in Figure The alarm type can be selected to: Audio Warning, Notify Surveillance Center, and Send . Please refer to Chapter 8.6 Setting Alarm Response Actions. Figure Configure HDD Error Alarm 4. Click the Apply button to save the settings 144

145 Chapter 11 Camera Settings 145

146 11.1 Configuring OSD Settings Purpose: You can configure the OSD (On-screen Display) settings for the camera, including date /time, camera name, etc. 1. Enter the OSD Configuration interface. Menu > Camera > OSD 2. Select the camera to configure OSD settings. 3. Edit the Camera Name in the text field. 4. Configure the Display Name, Display Date and Display Week by clicking the checkbox. 5. Select the Date Format, Time Format and Display Mode. Figure OSD Configuration Interface 6. You can use the mouse to click and drag the text frame on the preview window to adjust the OSD position. 7. Click the Apply button to apply the settings. 146

147 11.2 Configuring Privacy Mask Purpose: You are allowed to configure the four-sided privacy mask zones that cannot be viewed by the operator. The privacy mask can prevent certain surveillance areas to be viewed or recorded. 1. Enter the Privacy Mask Settings interface. Menu > Camera >Privacy Mask 2. Select the camera to set privacy mask. 3. Click the checkbox of Enable Privacy Mask to enable this feature. Figure Privacy Mask Settings Interface 4. Use the mouse to draw a zone on the window. The zones will be marked with different frame colors. Up to 4 privacy masks zones can be configured and the size of each area can be adjusted. 5. The configured privacy mask zones on the window can be cleared by clicking the corresponding Clear Zone1-4 icons on the right side of the window, or click Clear All to clear all zones. Figure Set Privacy Mask Area 6. Click the Apply button to save the settings. 147

148 11.3 Configuring Image Parameters 1. Enter the Image Settings interface. Menu > Camera >Image Figure Image Settings Interface 2. Select the camera to set image parameters. 3. You can click on the arrow to change the value of each parameter. 4. Click the Apply button to save the settings. 148

149 Chapter 12 NVR Management and Maintenance 149

150 12.1 Viewing System Information Viewing Device Information 1. Enter the System Information interface. Menu >Maintenance >System Info 2. Click the Device Info tab to enter the Device Information menu to view the device name, model, serial No., firmware version and encode version, as shown in Figure Figure Device Information Interface Viewing Camera Information 1. Enter the System Information interface. Menu >Maintenance>System Info 2. Click the Camera tab to enter the Camera Information menu to view the status of each camera, as shown in Figure Figure Camera Information Interface Viewing Record Information 1. Enter the System Information interface. Menu >Maintenance>System Info 2. Click the Record tab to enter the Record Information menu to view the recording status recording parameters of each camera, as shown in Figure

151 Figure Record Information Interface Viewing Alarm Information This function is not supported by DS-7100NI-SL and DS-7100NI-SL/W series NVR. 1. Enter the System Information interface. Menu >Maintenance>System Info 2. Click the Alarm tab to enter the Alarm Information menu to view the alarm information, as shown in Figure Figure Alarm Information Interface Viewing Network Information 1. Enter the System Information interface. Menu >Maintenance >System Info 2. Click the Network tab to enter the Network Information menu to view the network information, as shown in Figure Figure Network Information Interface 151

152 Viewing HDD Information 1. Enter the System Information interface. Menu >Maintenance>System Info 2. Click the HDD tab to enter the HDD Information menu to view the HDD status, free space, property, etc., as shown in Figure Figure HDD Information Interface 152

153 12.2 Searching & Export Log Files Purpose: The operation, alarm, exception and information of the NVR can be stored in log files, which can be viewed and exported at any time. 1. Enter the Log Information interface. Menu > Maintenance > Log Information Figure Log Search Interface 2. Set the log search conditions to refine your search, including the Start Time, End Time, Major Type and Minor Type. 3. Click the Search button to start search log files. 4. The matched log files will be displayed on the list shown below. 153

154 Figure Log Search Results Up to 2000 log files can be displayed each time. 5. You can click the button of each log or double click it to view its detailed information, as shown in Figure And you can also click the button to view the related video files if available. Figure Log Details 6. If you want to export the log files, click the Export button to enter the Export menu, as shown in Figure

155 Figure Export Log Files 7. Select the backup device from the dropdown list of Device Name. 8. Click the Export to export the log files to the selected backup device. You can click the New Folder button to create new folder in the backup device, or click the Format button to format the backup device before log export. Please connect the backup device to NVR before operating log export. The log files exported to the backup device are named by exporting time, e.g., logBack.txt. To export all the log files: You can enter the Log Export interface. Menu> Maintenance> Log Information> Log Export Figure Log Export Interface You can check the checkbox of the HDD. Click the Export button to export all the log files stored in the selected HDD. 155

156 12.3 Importing/Exporting Configuration Files Purpose: The configuration files of the NVR can be exported to local device for backup; and the configuration files of one NVR can be imported to multiple NVR devices if they are to be configured with the same parameters. 1. Enter the Import/Export Configuration File interface. Menu > Maintenance >Import/Export Figure Import/Export Config File 2. Click the Export button to export configuration files to the selected local backup device. 3. To import a configuration file, select the file from the selected backup device and click the Import button. After the import process is completed, you must reboot the NVR. After finishing the import of configuration files, the device will reboot automatically. 156

157 12.4 Upgrading System Purpose: The firmware on your NVR can be upgraded by local backup device or remote FTP server Upgrading by Local Backup Device 1. Connect your NVR with a local backup device where the update firmware file is located. 2. Enter the Upgrade interface. Menu >Maintenance>Upgrade 3. Click the Local Upgrade tab to enter the local upgrade menu, as shown in Figure Figure Local Upgrade Interface 4. Select the update file from the backup device. 5. Click the Upgrade button to start upgrading. 6. After the upgrading is complete, reboot the NVR to activate the new firmware Upgrading by FTP Before you start: Configure PC (running FTP server) and NVR to the same Local Area Network. Run the 3 rd -party TFTP software on the PC and copy the firmware into the root directory of TFTP. 1. Enter the Upgrade interface. Menu >Maintenance>Upgrade 2. Click the FTP tab to enter the local upgrade interface, as shown in Figure

158 Figure FTP Upgrade Interface 3. Enter the FTP Server Address in the text field. 4. Click the Upgrade button to start upgrading. 5. After the upgrading is complete, reboot the NVR to activate the new firmware. 158

159 12.5 Restoring Default Settings 1. Enter the Default interface. Menu > Maintenance > Default Figure Restore Factory Default 2. Click the OK button to restore the default settings. Except the network parameters (including IP address, subnet mask, gateway, MTU, default route and server port), all other parameters of the device will be restored to factory default settings. 159

160 Chapter 13 Others 160

161 13.1 Configuring General Settings Purpose: You can configure the output resolution, system time, mouse pointer speed through the Menu > Configuration > General interface. 1. Enter the General Settings interface. Menu >Configuration> General 2. Select the General tab. Figure General Settings Interface 3. Configure the following settings: Language: The default language used is English. Resolution: Select the output resolution, which must be the same with the resolution of the monitor screen. Time Zone: Select the time zone. Date Format: Select the date format. System Date: Select the system date. System Time: Select the system time. Mouse Pointer Speed: Set the speed of mouse pointer; 4 levels are configurable. Enable Wizard: Enable/disable the Wizard when the device starts up. Enable Password: Enable/disable the use of the login password. 4. Click the Apply button to save the settings. 161

162 13.2 Configuring DST Settings 1. Enter the General Settings interface. Menu >Configuration>General 2. Choose DST Settings tab. Figure DST Settings Interface You can check the checkbox before the Auto DST Adjustment item. Or you can manually check the Enable DST checkbox, and then you choose the date of the DST period. 3. Click Apply button to save the settings. 162

163 13.3 Configuring More Settings for Device Parameters 1. Enter the General Settings interface. Menu >Configuration>General 2. Click the More Settings tab to enter the More Settings interface, as shown in Figure Figure More Settings Interface 3. Configure the following settings: Device Name: Edit the name of NVR. Device No.: Edit the serial number of NVR. The Device No. can be set in the range of 1~255, and the default No. is 255. The number is used for the remote and keyboard control. Auto Logout: Set timeout time for menu inactivity. E.g., when the timeout time is set to 5 Minutes, then the system will exit from the current operation menu to live view screen after 5 minutes of menu inactivity. Menu Output Mode: You can choose the menu display on different video output. 4. Click the Apply button to save the settings. 163

164 13.4 Managing User Accounts Purpose: There is a default account in the NVR: Administrator. The Administrator user name is admin and the password is The Administrator has the permission to add and delete user and configure user parameters Adding a User 1. Enter the User Management interface. Menu >Configuration>User Figure User Management Interface 2. Click the Add button to enter the Add User interface. Figure Add User Menu 164

165 3. Enter the information for new user, including User Name, Password, Level and User s MAC Address. Level: Set the user level to Operator or Guest. Different user levels have different operating permission. Operator: The Operator user level has permission of Two-way Audio in Remote Configuration and all operating permission in Camera Configuration. Guest: The Guest user has no permission of Two-way Audio in Remote Configuration and only has the local/remote playback in the Camera Configuration. User s MAC Address: The MAC address of the remote PC which logs onto the NVR. If it is configured and enabled, it only allows the remote user with this MAC address to access the NVR. 4. Click the OK button to save the settings and go back to the User Management interface. The added new user will be displayed on the list, as shown in Figure Figure Added User Listed in User Management Interface 5. Select the user from the list and then click the button to enter the Permission settings interface, as shown in Figure Figure User Permission Settings Interface 6. Set the operating permission of Local Configuration, Remote Configuration and Camera Configuration for the user. Local Configuration Local Log Search: Searching and viewing logs and system information of NVR. Local Parameters Settings: Configuring parameters, restoring factory default parameters and importing/exporting configuration files. Local Camera Management: The adding, deleting and editing of IP cameras. 165

166 Local Advanced Operation: Operating HDD management (initializing HDD, setting HDD property), upgrading system firmware, clearing I/O alarm output. Local Shutdown Reboot: Shutting down or rebooting the NVR. Remote Configuration Remote Log Search: Remotely viewing logs that are saved on the NVR. Remote Parameters Settings: Remotely configuring parameters, restoring factory default parameters and importing/exporting configuration files. Remote Camera Management: Remote adding, deleting and editing of the IP cameras. Remote Video Output Control: Sending remote button control signal. Two-Way Audio: Realizing two-way radio between the remote client and the NVR. Remote Alarm Control: Remotely arming (notify alarm and exception message to the remote client) and controlling the alarm output. Remote Advanced Operation: Remotely operating HDD management (initializing HDD, setting HDD property), upgrading system firmware. Remote Shutdown/Reboot: Remotely shutting down or rebooting the NVR. Camera Configuration Remote Live View: Remotely viewing live video of the selected camera (s). Local Manual Operation: Locally starting/stopping manual recording and alarm output of the selected camera (s). Remote Manual Operation: Remotely starting/stopping manual recording and alarm output of the selected camera (s). Local Playback: Locally playing back recorded files of the selected camera (s). Remote Playback: Remotely playing back recorded files of the selected camera (s). Local PTZ Control: Locally controlling PTZ movement of the selected camera (s). Remote PTZ Control: Remotely controlling PTZ movement of the selected camera (s). Local Video Export: Locally exporting recorded files of the selected camera (s). 7. Click the OK button to save the settings and exit interface. Only the admin user account has the permission of restoring factory default parameters Deleting a User 1. Enter the User Management interface. Menu >Configuration>User 2. Select the user to be deleted from the list, as shown in Figure

167 Figure User List 3. Click the icon to delete the selected user Editing a User 1. Enter the User Management interface. Menu >Configuration>User 2. Select the user to be edited from the list, as shown in Figure Click the icon to enter the Edit User interface, as shown in Figure The admin user can also be edited. Figure Edit User Interface 4. Edit the user information, including user name, password, level and MAC address. Check the checkbox of Change Password if you want to change the password of the current user. 5. Click the OK button to save the settings and exit the menu. 167

168 Appendix 168

169 Glossary Dual Stream: Dual stream is a technology used to record high resolution video locally while transmitting a lower resolution stream over the network. The two streams are generated by the DVR, with the main stream having a maximum resolution of 4CIF and the sub-stream having a maximum resolution of CIF. HDD: Acronym for Hard Disk Drive. A storage medium which stores digitally encoded data on platters with magnetic surfaces. DHCP: Dynamic Host Configuration Protocol (DHCP) is a network application protocol used by devices (DHCP clients) to obtain configuration information for operation in an Internet Protocol network. HTTP: Acronym for Hypertext Transfer Protocol. A protocol to transfer hypertext request and information between servers and browsers over a network PPPoE: PPPoE, Point-to-Point Protocol over Ethernet, is a network protocol for encapsulating Point-to-Point Protocol (PPP) frames inside Ethernet frames. It is used mainly with ADSL services where individual users connect to the ADSL transceiver (modem) over Ethernet and in plain Metro Ethernet networks. DDNS: Dynamic DNS is a method, protocol, or network service that provides the capability for a networked device, such as a router or computer system using the Internet Protocol Suite, to notify a domain name server to change, in real time (ad-hoc) the active DNS configuration of its configured hostnames, addresses or other information stored in DNS. Hybrid DVR: A hybrid DVR is a combination of a DVR and NVR. NTP: Acronym for Network Time Protocol. A protocol designed to synchronize the clocks of computers over a network. NTSC: Acronym for National Television System Committee. NTSC is an analog television standard used in such countries as the United States and Japan. Each frame of anntsc signal contains 525 scan lines at 60Hz. NVR: Acronym for Network Video Recorder. An NVR can be a PC-based or embedded system used for centralized management and storage for IP cameras, IP Domes and other DVRs. PAL: Acronym for Phase Alternating Line. PAL is also another video standard used in broadcast televisions systems in large parts of the world. PAL signal contains 625 scan lines at 50Hz. PTZ: Acronym for Pan, Tilt, Zoom. PTZ cameras are motor driven systems that allow the camera to pan left and right, tilt up and down and zoom in and out. USB: Acronym for Universal Serial Bus. USB is a plug-and-play serial bus standard to interface devices to a host computer. 169

170 Troubleshooting No image displayed on the monitor after starting up normally. Possible Reasons a) No VGA or HDMI connections. b) Connection cable is damaged. c) Input mode of the monitor is incorrect. Steps 1. Verify the device is connected with the monitor via HDMI or VGA cable. If not, please connect the device with the monitor and reboot. 2. Verify the connection cable is good. If there is still no image display on the monitor after rebooting, please check if the connection cable is good, and change a cable to connect again. 3. Verify Input mode of the monitor is correct. Please check the input mode of the monitor matches with the output mode of the device (e.g. if the output mode of NVR is HDMI output, then the input mode of monitor must be the HDMI input). And if not, please modify the input mode of monitor. 4. Check if the fault is solved by the step 1 to step 3. If it is solved, finish the process. If not, please contact the engineer from Hikvision to do the further process. There is an audible warning sound Di-Di-Di-DiDi after a new bought NVR starts up. Possible Reasons a) No HDD is installed in the device. b) The installed HDD has not been initialized. c) The installed HDD is not compatible with the NVR or is broken-down. Steps 1. Verify at least one HDD is installed in the NVR. If not, please install the compatible HDD. Please refer to the Quick Operation Guide for the HDD installation steps. If you don t want to install a HDD, select Menu>Configuration > Exceptions, and uncheck the Audible Warning checkbox of HDD Error. 2. Verify the HDD is initialized. 1) Select Menu>HDD>General. 2) If the status of the HDD is Uninitialized, please check the checkbox of corresponding HDD and click the Init button. 3. Verify the HDD is detected or is in good condition. 1) Select Menu>HDD>General. 2) If the HDD is not detected or the status is Abnormal, please replace the dedicated HDD according to the requirement. 4. Check if the fault is solved by the step 1 to step 3. If it is solved, finish the process. If not, please contact the engineer from Hikvision to do the further process. The status of the added IP Camera displays as Disconnected when it is connected through Hikvision 170

171 Protocol. Select Menu>Camera>Camera>IP Camera to get the camera status. Possible Reasons a) Network failure, and the NVR and IP camera lost connections. b) The configured parameters are incorrect when adding the IP camera. c) Insufficient bandwidth. Steps 1. Verify the network is connected. Open the Command Prompt, and execute the ping command. Input ping IP (e.g. ping ). Simultaneously press Ctrl and C to exit the ping command. If there exists return information and the time value is little, the network is normal. 2. Verify the configuration parameters are correct. 1) Select Menu>Camera>Camera>IP Camera. 2) Verify the following parameters are the same with those of the connected IP devices, including IP address, protocol, management port, user name and password. 3. Verify the whether the bandwidth is enough. 1) Select Menu >Maintenance > Net Detect > Network Stat.. 2) Check the usage of the access bandwidth, and see if the total bandwidth has reached its limit. 4. Check if the fault is solved by the step 1 to step 3. If it is solved, finish the process. If not, please contact the engineer from Hikvision to do the further process. The IP camera frequently goes online and offline and the status of it displays as Disconnected. Possible Reasons a) The IP camera and the NVR versions are not compatible. b) Unstable power supply of IP camera. c) Unstable network between IP camera and NVR. d) Limited flow by the switch connected with IP camera and NVR. Steps 1. Verify the IP camera and the NVR versions are compatible. 1) Enter the IP camera Management interface Menu > Camera > Camera>IP Camera, and view the firmware version of connected IP camera. 2) Enter the System Info interface Menu>Maintenance>System Info>Device Info, and view the firmware version of NVR. 2. Verify power supply of IP camera is stable. 1) Verify the power indicator is normal. 2) When the IP camera is offline, please try the ping command on PC to check if the PC connects with the IP camera. 3. Verify the network between IP camera and NVR is stable. Open the Command Prompt, use the ping command and keep sending large data packages to the connected IP camera, and check if there exists packet loss. Simultaneously press Ctrl and C to exit the ping command. Example: Input ping l 1472 f. 4. Verify the switch is not flow control. Check the brand, model of the switch connecting IP camera and NVR, and contact with the manufacturer of the switch to check if it has the function of flow control. If so, please turn it down. 171

172 5. Check if the fault is solved by the step 1 to step 4. If it is solved, finish the process. If not, please contact the engineer from Hikvision to do the further process. No monitor connected with the NVR locally and when you manage the IP camera to connect with the device by web browser remotely, of which the status displays as Connected. And then you connect the device with the monitor via VGA or HDMI interface and reboot the device, there is black screen with the mouse cursor. Connect the NVR with the monitor before startup via VGA or HDMI interface, and manage the IP camera to connect with the device locally or remotely, the status of IP camera displays as Connect. And then connect the device with the CVBS, and there is black screen either. Possible Reasons: After connecting the IP camera to the NVR, the image is output via the main spot interface by default. 1. Enable the output channel. 2. Select Menu > Configuration > Live View > View, and select video output interface in the drop-down list and configure the window you want to view. The view settings can only be configured by the local operation of NVR. Different camera orders and window-division modes can be set for different output interfaces separately, and digits like D1 and D2 stands for the channel number, and X means the selected window has no image output. 3. Check if the fault is solved by the above steps. If it is solved, finish the process. If not, please contact the engineer from Hikvision to do the further process. Live view stuck when video output locally. Possible Reasons: a) Poor network between NVR and IP camera, and there exists packet loss during the transmission. b) The motion detection and alarm functions are enabled, and the parameters of Main Stream (Normal) and Main Stream (Event) are different. So the image looks stuck due to the image changes between different resolutions. c) The frame rate has not reached the real-time frame rate. 1. Verify the network between NVR and IP camera is connected. 1) When image is stuck, connect the RS-232 ports on PC and the rear panel of NVR with the RS-232 cable. 2) Open the Super Terminal, and execute the command of ping l 1472 f (the IP address may change according to the real condition), and check if there exists packet loss. Simultaneously press Ctrl and C to exit the ping command. 2. Check the parameters of Main Stream (Normal) and Main Stream (Event). Select Menu > Record > Parameters > Record, and set the resolution of Main Stream (Event) the same as the one of Main Stream (Normal). 3. Verify the frame rate is real-time frame rate. Select Menu > Record > Parameters > Record, and set the Frame rate to Full Frame. 172

173 4. Check if the fault is solved by the above steps. If it is solved, finish the process. If not, please contact the engineer from Hikvision to do the further process. Live view stuck when video output remotely via the Internet Explorer or platform software. Possible Reasons: a) Poor network between NVR and IP camera, and there exists packet loss during the transmission. b) Poor network between NVR and PC, and there exists packet loss during the transmission. c) The performances of hardware are not good enough, including CPU, memory, etc.. 1. Verify the network between NVR and IP camera is connected. Open the Command Prompt, and execute the command of ping l 1472 f (the IP address may change according to the real condition), and check if there exists packet loss. Simultaneously press Ctrl and C to exit the ping command. 2. Verify the network between NVR and PC is connected. 1) Open the Command Prompt in the Start menu, or you can press windows+r shortcut key to open it. 2) Use the ping command to send large packet to the NVR, execute the command of ping l 1472 f (the IP address may change according to the real condition), and check if there exists packet loss. Simultaneously press Ctrl and C to exit the ping command. 3. Verify the hardware of the PC is good enough. Simultaneously press Ctrl, Alt and Delete to enter the windows task management interface, as shown in the following figure. Windows task management interface Select the Performance tab; check the status of the CPU and Memory. If the resource is not enough, please end some unnecessary processes. 173

Network Video Recorder User Manual

Network Video Recorder User Manual Network Video Recorder User Manual UD.6L0202D1131A01 Hikvision Network Digital Video Recorder User Manual This manual, as well as the software described in it, is furnished under license and may be used

More information

DS-7200HWI-SH/A Series DVR. Technical Specification

DS-7200HWI-SH/A Series DVR. Technical Specification DS-7200HWI-SH/A Series DVR Technical Specification Notices The information in this documentation is subject to change without notice and does not represent any commitment on behalf of HIKVISION. HIKVISION

More information

DS-7600NI-SE/P Series NVR. Technical Specification

DS-7600NI-SE/P Series NVR. Technical Specification DS-7600NI-SE/P Series NVR Technical Specification Notices The information in this documentation is subject to change without notice and does not represent any commitment on behalf of HIKVISION. HIKVISION

More information

Network Video Recorder Quick Operation Guide

Network Video Recorder Quick Operation Guide Network Video Recorder Quick Operation Guide UD.6L0202B1283A01 TABLE OF CONTENTS NVR Pre-Installation... 2 NVR Installation... 2 Hard Disk Installation... 2 Front Panel... 4 Rear Panel... 5 Specifications...

More information

Digital Video Recorder User Manual (V2.2.4)

Digital Video Recorder User Manual (V2.2.4) Digital Video Recorder User Manual (V2.2.4) UD.6L0202B0068A02 Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device,

More information

POWERED BY. User Manual POWERED BY

POWERED BY. User Manual POWERED BY User Manual SERIES Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. This manual is applicable to: S04, S08, S16. This manual may contain

More information

Digital Video Recorder

Digital Video Recorder Digital Video Recorder User Manual Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. This manual may contain several technically incorrect

More information

POWERED BY. EPCOM Slim Line. Powered by Hikvision. Technical Specification

POWERED BY. EPCOM Slim Line. Powered by Hikvision. Technical Specification POWERED BY EPCOM Slim Line Powered by Hikvision Notices The information in this documentation is subject to change without notice and does not represent any commitment on behalf of HIKVISION. HIKVISION

More information

aseries DVR04/DVR08 DIGITAL VIDEO RECORDER Quick Operations Guide

aseries DVR04/DVR08 DIGITAL VIDEO RECORDER Quick Operations Guide aseries DVR04/DVR08 DIGITAL VIDEO RECORDER Quick Operations Guide UD.7L0202B1365B01 Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer.

More information

DS-9500NI-ST Series NVR. Technical Specification

DS-9500NI-ST Series NVR. Technical Specification DS-9500NI-ST Series NVR Technical Specification Notices The information in this documentation is subject to change without notice and does not represent any commitment on behalf of HIKVISION. HIKVISION

More information

DS-7600NI-SE/P Series NVR USER S MANUAL Version 2.3.9

DS-7600NI-SE/P Series NVR USER S MANUAL Version 2.3.9 DS-7600NI-SE/P Series NVR USER S MANUAL Version 2.3.9 1 Hikvision Network Video Recorder User s Manual This manual, as well as the software described in it, is furnished under license and may be used or

More information

Network Video Recorder User Manual

Network Video Recorder User Manual Network Video Recorder User Manual UD.6L0202D1275A02 Regulatory information FCC information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant

More information

KNR-p4Px4 KNR-p16Px8. Network Video Recorder. User Manual

KNR-p4Px4 KNR-p16Px8. Network Video Recorder. User Manual KNR-p4Px4 KNR-p16Px8 Network Video Recorder User Manual Regulatory information FCC information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant

More information

ES-RN080201-A ES-RN160201-A. Series NVR. Technical Specification

ES-RN080201-A ES-RN160201-A. Series NVR. Technical Specification ES-RN080201-A ES-RN160201-A Series NVR Notices The information in this documentation is subject to change without notice and does not represent any commitment on behalf of EMERSON. EMERSON disclaims any

More information

ALI-NVR3004P, ALI-NVR3008P Embedded Network Video Recorder Quick Setup Guide

ALI-NVR3004P, ALI-NVR3008P Embedded Network Video Recorder Quick Setup Guide ALI-NVR3004P, ALI-NVR3008P Embedded Network Video Recorder Quick Setup Guide This quick setup guide provides instructions to initially setup and use your new network video recorder. For additional information

More information

Network Video Recorder Quick Operation Guide

Network Video Recorder Quick Operation Guide Network Video Recorder Quick Operation Guide UD.6L0202B1119A01 Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. This manual is applicable

More information

DS-7608NI-S Series NVR. Technical Manual

DS-7608NI-S Series NVR. Technical Manual DS-7608NI-S Series NVR Technical Manual Notices The information in this documentation is subject to change without notice and does not represent any commitment on behalf of HIKVISION. HIKVISION disclaims

More information

DS-7300HWI-SH Series DVR. Technical Specification

DS-7300HWI-SH Series DVR. Technical Specification DS-7300HWI-SH Series DVR Technical Specification Notices The information in this documentation is subject to change without notice and does not represent any commitment on behalf of HIKVISION. HIKVISION

More information

Digital Video Recorder User Manual

Digital Video Recorder User Manual Digital Video Recorder User Manual UD.6L0202D1360A01 Hikvision Network Digital Video Recorder User s Manual This manual, as well as the software described in it, is furnished under license and may be used

More information

Network Video Recorder

Network Video Recorder Network Video Recorder User Manual Regulatory information FCC information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of

More information

Quick Operation Guide of Network Video Recorder. Quick Start Guide

Quick Operation Guide of Network Video Recorder. Quick Start Guide Quick Start Guide TABLE OF CONTENTS NVR Pre-Installation...6 NVR Installation...6 HDD Installation...7 Main Features...9 Typical Application...10 Front Panel and Rear Panel...11 Accessing by Web Browser...13

More information

ivms-4200 Client Software User Manual Version 1.02

ivms-4200 Client Software User Manual Version 1.02 ivms-4200 Client Software User Manual Version 1.02 Contents Chapter 1. Overview... 3 1.1 Description... 3 1.2 Running Environment... 3 Chapter 2. Starting ivms-4200... 4 2.1 User Registration... 4 2.2

More information

MAC CMS User Manual 1

MAC CMS User Manual 1 1 TABLE OF CONTENTS Chapter 1. Overview... 4 Chapter 2. Starting CMS Client... 4 2.1 User Registration... 4 2.2 Wizard for Importing Device... 4 2.3 User Login... 9 2.4 Control Panel and Main Menu Bar

More information

Digital Video Recorder User Manual (V2.2.3)

Digital Video Recorder User Manual (V2.2.3) Digital Video Recorder User Manual (V2.2.3) UD.6L0202D1018A01 eohikvision Network Digital Video Recorder User s Manual This manual, as well as the software described in it, is furnished under license and

More information

User Manual ivms-4200 Client Software. Version 1.02

User Manual ivms-4200 Client Software. Version 1.02 User Manual ivms-4200 Client Software Version 1.02 TABLE OF CONTENTS Chapter 1. Overview... 3 Chapter 2. Starting ivms-4200... 3 2.1 User Registration... 3 2.2 Wizard for Importing Device... 3 2.3 User

More information

NVMS-1200. User Manual

NVMS-1200. User Manual NVMS-1200 User Manual Contents 1 Software Introduction... 1 1.1 Summary... 1 1.2 Install and Uninstall... 1 1.2.1 Install the Software... 1 2 Login Software... 3 2.1 Login... 3 2.2 Control Panel Instruction...

More information

Multi-Site 4200. Remote Viewing Software. User Guide

Multi-Site 4200. Remote Viewing Software. User Guide Multi-Site 4200 Remote Viewing Software User Guide Document 800-12064V1 Rev A 09/2012 User Guide Revisions Issue Date Revisions A 07/2012 New document. V1 Rev A 09/2012 Updated the description of the

More information

DS-7208/DS-7216HVI-S DVR USER S MANUAL

DS-7208/DS-7216HVI-S DVR USER S MANUAL DS-7208/DS-7216HVI-S DVR USER S MANUAL Hikvision Network Digital Video Recorder User Guide Copyright 2009, Hikvision, Ltd. All rights reserved. This document may not be copied in whole or in part or otherwise

More information

Network Video Recorder

Network Video Recorder Network Video Recorder XC-4CH-NVR-1TB and XC-8CH-NVR-2TB Username: admin Password: 12345 Quick Operation Guide XC-4CH-NVR-1TB and XC-8CH-NVR-2TB quick guide TABLE OF CONTENTS NVR Pre-Installation... 2

More information

Digital Video Recorder User Manual

Digital Video Recorder User Manual Digital Video Recorder User Manual UD.6L0202D1623A01 Hikvision Network Digital Video Recorder User Manual This manual, as well as the software described in it, is furnished under license and may be used

More information

Digital Video Recorder User Manual

Digital Video Recorder User Manual Digital Video Recorder User Manual UD.6L0202D1589A01 Hikvision Network Digital Video Recorder User s Manual This manual, as well as the software described in it, is furnished under license and may be used

More information

Network Video Recorder. Operation Manual

Network Video Recorder. Operation Manual Network Video Recorder Operation Manual Content 1 Product Description... 1 1.1 Product Overview... 1 1.2 Specification... 1 2 Product Structure Introduction... 2 2.1 Back Interface... 2 2.2 Front Panel...

More information

Network Video Recorder NVR-CH4 NVR-CH8 NVR-CH16

Network Video Recorder NVR-CH4 NVR-CH8 NVR-CH16 Network Video Recorder NVR-CH4 NVR-CH8 NVR-CH16 User Manual V1.1 For further information, including datasheets, FAQ and technical support please visit: www.hills.com.au/videosecurity 1 Regulatory information

More information

Digital Video Recorder. User Manual UD.6L0202D1962A01

Digital Video Recorder. User Manual UD.6L0202D1962A01 Digital Video Recorder User Manual UD.6L0202D1962A01 User Manual COPYRIGHT 2015 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings,

More information

ENR Series Network Video Recorder. User Manual

ENR Series Network Video Recorder. User Manual ENR Series Network Video Recorder User Manual About this Manual This Manual is applicable to Network Video Recorder (NVR). The Manual includes instructions for using and managing the product. Pictures,

More information

DS-7208HVI-ST Series DVR. Technical Manual

DS-7208HVI-ST Series DVR. Technical Manual DS-7208HVI-ST Series DVR Technical Manual Notices The information in this documentation is subject to change without notice and does not represent any commitment on behalf of HIKVISION. HIKVISION disclaims

More information

DS-7208&7216HVI-S Series Embedded Net DVR USER S MANUAL

DS-7208&7216HVI-S Series Embedded Net DVR USER S MANUAL DS-7208&7216HVI-S Series Embedded Net DVR USER S MANUAL Hikvision Network Digital Video Recorder User Guide Copyright 2010, Hikvision, Ltd. All rights reserved. This document may not be copied in whole

More information

ivms-4200 Client Software Quick Start Guide V1.02

ivms-4200 Client Software Quick Start Guide V1.02 ivms-4200 Client Software Quick Start Guide V1.02 Contents 1 Description... 2 1.1 Running Environment... 2 1.2 Surveillance System Architecture with an Performance of ivms-4200... 3 2 Starting ivms-4200...

More information

ImagineWorldClient Client Management Software. User s Manual. (Revision-2)

ImagineWorldClient Client Management Software. User s Manual. (Revision-2) ImagineWorldClient Client Management Software User s Manual (Revision-2) (888) 379-2666 US Toll Free (905) 336-9665 Phone (905) 336-9662 Fax www.videotransmitters.com 1 Contents 1. CMS SOFTWARE FEATURES...4

More information

User Manual (V1.03) UD.6L0201D1056A01

User Manual (V1.03) UD.6L0201D1056A01 ivms-4200 PCNVR User Manual (V1.03) UD.6L0201D1056A01 Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact the dealer. This manual applies to ivms-4200

More information

VMS A1 Client Software. User Manual (V2.0)

VMS A1 Client Software. User Manual (V2.0) VMS A1 Client Software User Manual (V2.0) Contents Chapter 1 Overview...4 1.1 Description...4 1.2 Running Environment...4 1.3 Function Modules...5 Chapter 2 Live View...7 2.1 User Registration and Login...7

More information

Stand Alone Type. Digital Video Recorder USER S MANUAL. (Real time recording 8 & 16 CH DVR) Revision Date : 2010. 6. 30.

Stand Alone Type. Digital Video Recorder USER S MANUAL. (Real time recording 8 & 16 CH DVR) Revision Date : 2010. 6. 30. Stand Alone Type Digital Video Recorder USER S MANUAL (Real time recording 8 & 16 CH DVR) Revision Date : 2010. 6. 30. INDEX 1. Front Panel - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

More information

DS-7300HWI-SH Series. DS-7200HWI-SH Series DVR USER S MANUAL. Version 2.2.2

DS-7300HWI-SH Series. DS-7200HWI-SH Series DVR USER S MANUAL. Version 2.2.2 DS-7300HWI-SH Series DS-7200HWI-SH Series DVR USER S MANUAL Version 2.2.2 Hikvision Network Digital Video Recorder User s Manual This manual, as well as the software described in it, is furnished under

More information

NVMS - 1000 USER MANUAL. Version 2.1.0

NVMS - 1000 USER MANUAL. Version 2.1.0 NVMS - 1000 USER MANUAL Version 2.1.0 Contents 1 Software Introduction... 1 1.1 Summary... 1 1.2 Operation Environment... 1 1.3 Install and Uninstall... 2 1.3.1 Install the Software... 2 1.3.2 Uninstall

More information

ACS CLIENT SOFTWARE USER MANUAL

ACS CLIENT SOFTWARE USER MANUAL ACS CLIENT SOFTWARE USER MANUAL 1 ACS USER GUIDE 1.1 System Requirement Recommended System Requirement OS CPU VGA RAM HDD WindowXP, Vista Pentium 4, 2Ghz 1024*768, 64MB 24bit color graphic card 1GB 20MB

More information

Quick Start Guide NVR DS-7104NI-SL/W NVR. www.hikvision.com. First Choice For Security Professionals

Quick Start Guide NVR DS-7104NI-SL/W NVR. www.hikvision.com. First Choice For Security Professionals Quick Start Guide NVR DS-7104NI-SL/W NVR NOTE: For more detailed information, refer to the User s Manual on the CD-ROM. You must use your PC or MAC to access the files. www.hikvision.com Quick Start 1.

More information

Firmware Version 2.2.0.42 Recovision Technology Co., Ltd. 2014/03/12

Firmware Version 2.2.0.42 Recovision Technology Co., Ltd. 2014/03/12 RV1000 SERIES USER MANUAL Firmware Version 2.2.0.42 Recovision Technology Co., Ltd. 2014/03/12 Installation Notes: Please be advised of the following tips before using your NVR: Keep all liquids away from

More information

Network Video Recorder. Quick Start Guide XC-16CH-NVR-4TB. Username: admin. Password: 12345. XC-16CH-NVR-4TB quick guide

Network Video Recorder. Quick Start Guide XC-16CH-NVR-4TB. Username: admin. Password: 12345. XC-16CH-NVR-4TB quick guide Network Video Recorder XC-16CH-NVR-4TB Username: admin Password: 12345 Quick Start Guide XC-16CH-NVR-4TB quick guide TABLE OF CONTENTS NVR Pre-Installation... 2 NVR Installation... 2 Hard Disk Installation...

More information

KNR-p4Px4 KNR-p16Px8. Network Video Recorder. Quick Installation Guide

KNR-p4Px4 KNR-p16Px8. Network Video Recorder. Quick Installation Guide KNR-p4Px4 KNR-p16Px8 Network Video Recorder Quick Installation Guide TABLE OF CONTENTS NVR Pre-Installation... 2 NVR Installation... 2 Hard Disk Installation... 2 Front Panel... 4 Rear Panel... 5 Specifications...

More information

A quick user guide for your LX Apollo DVR

A quick user guide for your LX Apollo DVR A quick user guide for your LX Apollo DVR The LX Apollo series of DVR s is designed specially for the security and surveillance field and is an outstanding digital surveillance product. It has an embedded

More information

Amcrest 960H DVR Quick Start Guide

Amcrest 960H DVR Quick Start Guide Amcrest 960H DVR Quick Start Guide Welcome Thank you for purchasing our Amcrest 960H DVR! This quick start guide will help you become familiar with our DVR in a very short time. Before installation and

More information

ivms-4200 Client Software User Manual (V2.0.0)

ivms-4200 Client Software User Manual (V2.0.0) ivms-4200 Client Software User Manual (V2.0.0) UD.6L0201D1034A01 Contents Chapter 1 Overview... 3 1.1 Description... 3 1.2 Running Environment... 3 1.3 Function Modules... 3 1.4 Updates Instruction...

More information

EV-1000 Series DVR. Quick Operation Guide. Version 1.0.0

EV-1000 Series DVR. Quick Operation Guide. Version 1.0.0 EV-1000 Series DVR Quick Operation Guide Version 1.0.0 Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. This manual is applicable to

More information

BlackHawk for MAC Software User Guide

BlackHawk for MAC Software User Guide BlackHawk for MAC Software User Guide Products: BLK-DH2 Series and BLK-HD Series DVRs Please read this manual before using your software, and always follow the instructions for safety and proper use. Save

More information

DS-9000-ST Series Hybrid DVR DS-9600-ST/RT/XT Series NVR DS-7700NI-SP Series NVR USER S MANUAL Version 3.1

DS-9000-ST Series Hybrid DVR DS-9600-ST/RT/XT Series NVR DS-7700NI-SP Series NVR USER S MANUAL Version 3.1 DS-9000-ST Series Hybrid DVR DS-9600-ST/RT/XT Series NVR DS-7700NI-SP Series NVR USER S MANUAL Version 3.1 1 Hikvision Network Digital Video Recorder User s Manual This manual, as well as the software

More information

User s Manual of DVR DVS Remote Client Software V 4.0.1

User s Manual of DVR DVS Remote Client Software V 4.0.1 User s Manual of DVR DVS Remote Client Software V 4.0.1 Index Version description...4 1 Introduction...8 2 Software Install, Uninstall and use...9 2.1 Install remote client software ver4.0.1...9 2.2 Uninstall

More information

Quick Start Guide. Plug n Play NVR DS-7604NI-E1/4P DS-7608NI-E2/8P. www.hikvision.com/en/us

Quick Start Guide. Plug n Play NVR DS-7604NI-E1/4P DS-7608NI-E2/8P. www.hikvision.com/en/us Quick Start Guide Plug n Play NVR DS-7604NI-E1/4P DS-7608NI-E2/8P Note: For more information refer to the complete User Manual located on the CD-ROM OVERVIEW 1. Overview 2. Main Menu Layout 3. Formatting

More information

Hills Video Security CCTV PC Client

Hills Video Security CCTV PC Client Hills Video Security CCTV PC Client User Manual V1.1 Contents Chapter 1 Overview... 3 1.1 Description... 3 1.2 Running Environment... 3 1.3 Function Modules... 4 1.4 Updates Instruction... 6 Chapter 2

More information

Client Software-4000(V2.00.02) User Manual

Client Software-4000(V2.00.02) User Manual Client Software-4000(V2.00.02) User Manual Index Chapter 1 Welcome to Client Software-4000 (V2.0)... 1 1.1 Overview... 1 1.2 Computer Disposition Request... 1 1.3 Convention... 1 Chapter 2 Install & Uninstall...

More information

DS-1100KI Network Keyboard User Manual V 1.0

DS-1100KI Network Keyboard User Manual V 1.0 DS-1100KI Network Keyboard User Manual V 1.0 Preventive and Cautionary Tips Before connecting and operating your keyboard, please be advised of the following tips: Ensure unit is placed in a well-ventilated,

More information

C n o t n e t n e t n s

C n o t n e t n e t n s Preface Thank you for choosing our product, for a better understanding of the product, we recommend you read the instruction and safety information before use. Notice: This user manual is an operation

More information

Digital Video Recorder

Digital Video Recorder Digital Video Recorder User Manual Regulatory information FCC information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of

More information

Central Management Software CV3-M1024

Central Management Software CV3-M1024 Table of Contents Chapter 1. User Interface Overview...5 Chapter 2. Installation...6 2.1 Beginning Installation...6 2.2 Starting the CMS software...10 2.3 Starting it from the Start menu...10 2.4 Starting

More information

ENR-2000 Series. User s Manual. For V4.00.02 Firmware 2014/01/29

ENR-2000 Series. User s Manual. For V4.00.02 Firmware 2014/01/29 ENR-2000 Series User s Manual For V4.00.02 Firmware 2014/01/29 Legal Notice Disclaimer The information contained in this document is intended for general information purposes. ACTi Corporation shall not

More information

User Manual of Web Client

User Manual of Web Client User Manual of Web Client 1 Index Chapter 1 Software Installation... 3 Chapter 2 Begin to Use... 5 2.1 Login and Exit... 5 2.2 Preview Interface Instruction... 6 2.3 Preview Image... 7 Chapter 3 Playback...

More information

Instruction Manual FLIR Cloud Services Client

Instruction Manual FLIR Cloud Services Client Instruction Manual FLIR Cloud Services Client Instruction Manual FLIR Cloud Services Client #LX400018; r. 2.0/14567/14568; en-us iii Table of contents 1 Setting up FLIR Cloud Client for PC or Mac...1

More information

CDVS-7000 Series Remote Software Users Guide

CDVS-7000 Series Remote Software Users Guide CDVS-7000 Series Remote Software Users Guide Crest Electronics, Inc. Version 12.1005 Remote Surveillance Program The remote surveillance program enables users of the Crest 7000 series DVRs to connect remotely

More information

PC-ZViewer User Manual

PC-ZViewer User Manual PC-ZViewer User Manual For further help, please visit www.zmodo.com Contents Preface... 3 Statement... 3 Intended Reader... 3 Terms in this Manual... 3 Software Introduction... 3 Operating Environment...

More information

Central Management System (CMS) USER MANUAL

Central Management System (CMS) USER MANUAL Central Management System (CMS) USER MANUAL LEGAL INFORMATION Reproduction, transfer, distribution or storage of part or all of the contents in this document in any form without the prior written permission

More information

VFS24/32HDIP. Public Display IP Monitor User Manual

VFS24/32HDIP. Public Display IP Monitor User Manual VFS24/32HDIP Public Display IP Monitor User Manual 2 Contents Before You Begin...4 Side Panel Control buttons...6 Connections...7 OSD Function...7 LCD monitor Mounting Guide...9 Getting started... 10 Power

More information

HRG4, HRG8, HRG16 Performance DVRs Getting Started Guide

HRG4, HRG8, HRG16 Performance DVRs Getting Started Guide HRG4, HRG8, HRG16 Performance DVRs Getting Started Guide Document 800-12006V2 Rev A 07/2012 This document describes the installation and operation procedures for the following Performance Series Honeywell

More information

Access to remote DVR from IE USER S MANUAL CONTENT

Access to remote DVR from IE USER S MANUAL CONTENT Access to remote DVR from IE CONTENT... 2 Preface... 2 1. Introduction... 2 2. System requirement and executing environment... 2 2.1. Supported operating System:... 2 2.2. Hardware requirement (recommend):...

More information

ivms-4000 (V2.03.07) Client Software User Manual

ivms-4000 (V2.03.07) Client Software User Manual ivms-4000 (V2.03.07) Client Software User Manual Table of Contents User Manual... 2 Table of Contents... 1 Chapter 1 Welcome to ivms-4000 (V2.03.04.07)... 4 1.1 Overview... 4 1.2 Computer Disposition Request...

More information

User Manual V1.0. Remote Software

User Manual V1.0. Remote Software User Manual V1.0 Notice: The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change

More information

Mirasys NVR 6.1. User s Guide

Mirasys NVR 6.1. User s Guide Mirasys NVR 6.1 User s Guide CONTENTS Contents... 2 Before you start... 3 Introduction... 6 Logging in... 9 User interface... 13 Navigator... 16 Cameras... 25 Video outputs... 41 Digital outputs... 46

More information

ivms-5200 Professional Web Manager User Manual

ivms-5200 Professional Web Manager User Manual ivms-5200 Professional Web Manager User Manual UD.6L0202D1651A01 Hikvision ivms-5200 Professional Web Manager User Manual This manual, as well as the software described in it, is furnished under license

More information

LOREX CLIENT Remote Software 4.0

LOREX CLIENT Remote Software 4.0 LOREX CLIENT Remote Software 4.0 Instruction Manual English Version 2.0 MODEL: L20WD800 Series www.lorexcctv.com Copyright 2008 LOREX Technology Inc. Table of Contents Table of Contents Software Installation...

More information

Accessing via Web Browser

Accessing via Web Browser Accessing via Web Browser Hikvision DVR/NVR can be accessed via web browsing. It provides the functionalities of live view, playback, log management, and configuration, etc. Note: This instruction is written

More information

Content. Chapter1 Start up and Main interface 2

Content. Chapter1 Start up and Main interface 2 Content Chapter1 Start up and Main interface 2 1.1 Start up 2 1.2 Main interface 3 1.2.1 Interface description 3 1.2.2 Local setup 6 1.2.3 Local search 6 1.2.4 Remote setup 6 1.2.5 Remote search 6 1.2.6

More information

AXIS Camera Station Quick Installation Guide

AXIS Camera Station Quick Installation Guide AXIS Camera Station Quick Installation Guide Copyright Axis Communications AB April 2005 Rev. 3.5 Part Number 23997 1 Table of Contents Regulatory Information.................................. 3 AXIS Camera

More information

CX Series. Video Recording Server. Quick Start Guide CX784 / CX788 / CX7816. Version 1.05.00

CX Series. Video Recording Server. Quick Start Guide CX784 / CX788 / CX7816. Version 1.05.00 CX Series Video Recording Server CX784 / CX788 / CX7816 Quick Start Guide Version 1.05.00 Contents 1.Introduction...1 1.1.Packages Contents...1 1.2.Hardware Features...2 1.3.Functional Features...4 1.4.Hard

More information

Remote Client Program... 3. Web Client... 39

Remote Client Program... 3. Web Client... 39 Remote Client / Web Client USER MANUAL T Series Digital Video Recorder Remote Client Program... 3 Remote Client Program Installation... 4 Remote Client... 6 Main Window... 6 Site Registration... 7 Group

More information

User Manual of CMS. Contents

User Manual of CMS. Contents CMS User Manual Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact the dealer. This manual applies to CMS. This manual may contain several technically

More information

Quick Start Guide. Hybrid DVR DS-90xxHFI-ST, DS-90xxHWI-ST Series. NVR DS-96xxNI-ST/RT Series. Plug n Play NVR DS-77xxNI-SP Series

Quick Start Guide. Hybrid DVR DS-90xxHFI-ST, DS-90xxHWI-ST Series. NVR DS-96xxNI-ST/RT Series. Plug n Play NVR DS-77xxNI-SP Series Quick Start Guide Hybrid DVR DS-90xxHFI-ST, DS-90xxHWI-ST Series NVR DS-96xxNI-ST/RT Series Plug n Play NVR DS-77xxNI-SP Series Note: For more information refer to the complete User Manual located on the

More information

GV-Keyboard. User's Manual V2.0

GV-Keyboard. User's Manual V2.0 GV-Keyboard User's Manual V2.0 Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. 2007 GeoVision, Inc. All rights reserved.

More information

IP EQUIPMENT WEB. User manual

IP EQUIPMENT WEB. User manual IP EQUIPMENT WEB User manual V1.0 Thank you for purchasing our products,please contact with us anytime if you have any question or requirement. It is possible that there might be inaccurate places, inconsistencies

More information

ivms 4000(V2.0) User Manual

ivms 4000(V2.0) User Manual ivms 4000(V2.0) User Manual Table of Contents Chapter 1 Welcome to ivms 4000 (V2.0)...4 1.1 Overview...4 1.2 Computer Disposition Request...4 1.3 Convention...4 Chapter 2 Install & Uninstall...5 2.1 Install

More information

DVS Net (Integration)

DVS Net (Integration) DVS Net (Integration) Installation and User s Guide Ver 11.10.x Digital Video Security System Digital Video Recorder www.tuniss.com PLEASE CALL TUNISS COMPUTER AT: 650-401-6138 FOR ANY QUASTIONS REGARDING

More information

ivms-4200 Client Software User Manual UD.6L0202D1939A01

ivms-4200 Client Software User Manual UD.6L0202D1939A01 ivms-4200 Client Software User Manual UD.6L0202D1939A01 User Manual COPYRIGHT 2015 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others,

More information

UC2 Video Surveillance Client. User Manual V1.0.6

UC2 Video Surveillance Client. User Manual V1.0.6 UC2 Video Surveillance Client User Manual V1.0.6 MODIFY STEPS VERSION WRITER STATUS DESCRIPTION DATE V1.0.3 BRIAN A Add access mode function 2011-4-11 V1.0.4 BRIAN A Add PTZ and user role and so on 2011-4-23

More information

QSD2316L DVR User s Manual

QSD2316L DVR User s Manual QSD2316L DVR User s Manual H.264-200 FPS /240 FPS 16-channel digital video recorder All rights reserved Rev 062408 QSD2316L DVR User s Manual CAUTION Please read this user manual carefully to ensure that

More information

HDCVI Series DVR Quick Start Guide

HDCVI Series DVR Quick Start Guide HDCVI Series DVR Quick Start Guide Version 1.1.0 Welcome Thank you for purchasing our HDCVI DVR! This quick start guide will help you become familiar with our HDCVI DVR in a very short time. Before installation

More information

DS-6101DI Series Decoder Server. Technical Manual

DS-6101DI Series Decoder Server. Technical Manual DS-6101DI Series Decoder Server Technical Manual Notices The information in this documentation is subject to change without notice and does not represent any commitment on behalf of HIKVISION. HIKVISION

More information

4-CH Hybrid Digital Video Recorder

4-CH Hybrid Digital Video Recorder 4-CH Hybrid Digital Video Recorder Key Features Hardware Embedded, highly-reliable standalone HDVR Supports 4-ch BNC connectors Supports dual local display (VGA and HDMI) Supports 3.5" SATA x 1 HDD Supports

More information

ivms-4200 Client Software Quick Start Guide

ivms-4200 Client Software Quick Start Guide ivms-4200 Client Software Quick Start Guide Notices The information in this documentation is subject to change without notice and does not represent any commitment on behalf of HIKVISION. HIKVISION disclaims

More information

ivms-4200 Intelligent Video Management System Quick Start Guide

ivms-4200 Intelligent Video Management System Quick Start Guide ivms-4200 Intelligent Video Management System Quick Start Guide Notices The information in this documentation is subject to change without notice and does not represent any commitment on behalf of HIKVISION.

More information

Network Video Recorder User Manual

Network Video Recorder User Manual Network Video Recorder User Manual UD.6L0202D1593A01 Hikvision Network Digital Video Recorder User Manual This manual, as well as the software described in it, is furnished under license and may be used

More information

Contents. 1.2 Software Installation... 1

Contents. 1.2 Software Installation... 1 Software Manual Contents 1 Software Installation... 1 1.1 Overview...1 1.2 Software Installation... 1 2 Introduction To Basic Function...5 2.1 Login System... 5 2.2 CMS Operating Interface...5 2.2.1 Operating

More information

DS-9000/DS-9100/DS-9600 Series DVR USER S MANUAL Version 1.2

DS-9000/DS-9100/DS-9600 Series DVR USER S MANUAL Version 1.2 DS-9000/DS-9100/DS-9600 Series DVR USER S MANUAL Version 1.2 Hikvision Network Digital Video Recorder User s Manual This manual, as well as the software described in it, is furnished under license and

More information

DVR-4TL/8TL/16TL Setup Guide

DVR-4TL/8TL/16TL Setup Guide Package Content DVR-4TL/8TL/16TL Setup Guide Inspect the DVR s packaging. Make sure that the DVR-4TL/8TL/16TL is packed properly. Remove all items from the box and make sure it contains the following items.

More information