2 Contents 1 Description Running Environment Surveillance System Architecture with an Performance of ivms Starting ivms Installing the Software Uninstalling the Software User Registration Wizard for Importing Device User Login Control Panel and Main Menu Bar Introduction Live View... 19
3 1 Description ivms-4200 is a video management software using a distributed structure to manage all the connectable devices. It can manage the NVR, DVR, IP cameras, compression card and decoders. With different management and configuration modules and a reasonable collocation, it provides many solutions for different surveillance scenario, medium or small scale. It is a steady and reliable system with functions like real-time monitoring, video recording and searching, file backup, TV wall displaying, etc. This user manual describes the function, configuration and operation steps of ivms-4200 software. To ensure the properness and stability of the software, please refer to the contents below and read the manual carefully before installation and operation. This user manual can be acquired from your supplier. 1.1 Running Environment Operating system: Microsoft Windows 7/Windows 2008(32/64 bit operating system), Windows 2003/2000/Windows XP(32 bit operating system) CPU:Intel Pentium IV 3.0 GHz or above Memory:1G or above Display: 1024*768 or above Note: To simultaneously live view for many channels, or for the channel with high resolution, the higher hardware configuration is needed. The software does not support 64 bit operating system; the above mentioned 64 bit operating system refers to the system which supports 32 bit operating system as well.
4 1.2 Surveillance System Architecture with an Performance of ivms-4200 Topological Diagram of LAN Connection: Topological Diagram of WAN Connection:
5 1.3 Feature Description: Up to 256 devices and 1024 channels can be added. Up to 256 camera groups can be added, and for each group 64 cameras can be added. A camera can be added to different groups. Up to 64 decoding devices can be added. 64 division screen layout and 64 channels simultaneous live view. 16 channels simultaneous playback and 4 channels synchronized playback. Up to 16 stream media servers can be added, the maximum channels forwarded by the stream media can be 200 channels (2M). 16 storage servers can be added. User Friendly Operation: Logical menu hierarchy; Movable tab sequence; Live view in multi-screen; Easy drag and draw channels selecting; Wizard for guiding basic operation;
6 2 Starting ivms Installing the Software Follow the installation prompts to install the software. Steps: 1. Double click the program file to enter the following InstallShield Wizard. 2. Click Next to start the InstallShield Wizard. Select the language (English) for installation, and then click Next to continue. 3. In the License Agreement dialog box, check the checkbox with I accept the terms of the license agreement.
7 4. Choose the application you need in the next interface. User Client is the application of the ivms PC NVR server is the same with the storage server; if you want to use the PC as a NVR, you can install this application. Stream media server is for forwarding the video stream and lowering the resource consumption. Decoding Server enables you to decoding the video source and displays them on the TV wall. Encoding Server can be run as a encoding device. Decoder server and encoder server are alternative. 5. Click Next button to enter the following interface. 6. Click Install button to install the software.
8 7. You can check the checkboxes to create the shortcut. 8. Click the Next button. 9. Click Finish button to finish the installation.
9 2.2 Uninstalling the Software 1. Click Start All Programs 4200 client and select Uninstall ivms-4200 option. to enter the following interface: 2. Select Remove to remove all the installed features and then click Next to uninstall ivms-4200 according to the prompt. 2.3 User Registration For the first time to use the ivms-4200 software, you need to register a super user for login. Enter the super user name, password and confirm the password in the dialog box and click Register. Then, you can log in as the super user. Note: Enter, Space, and TAB keys are invalid for the user name and password. The password cannot be empty, and it should not be less than six characters and can t be copied and pasted.
10 2.4 Wizard for Importing Device Purpose: The main function of the ivms-4200 is to manage devices remotely. Thus the task on the top hierarchy is to add the device to the management list. All the devices managed by the ivms-4200 must be connected to the IP network. For the first time user, the wizard message box pops up to ask you whether you want to be guided for the basic operation of the client software. If this is not the first time you use the client software, the wizard doesn t pop up, and you can also use the wizard, click Help and Open Wizard. Click Entering Guide to start the wizard, or click Cancel to exit the wizard. Steps: 1. According to the hint, click Add icon to add devices to the management list of the software.
11 2. Create a nickname for the device, enter the IP address and the port number of the remote device, enter the user name, and the password of the device. 3. Click Add icon to add the device. If you add the device with a domain name, you can check the Private Domain Mode checkbox. And create a nickname, enter the domain name and port number, and enter the admin name and password of the device to add the device.
12 You can also click Show online device to show the device connected to the same Local Area Network. Steps: 1) Select the device in the device list, and the information of the device such as the MAC address the software version and the serial number is shown in the left part. The information in this part can t be modified. 2) In the Network information area, you can modify the IP address the Subnet Mask and the Port number with entering the admin password of the device. 3) You can also recover the default password for the device, with the code provided by the authorized engineers.
13 4. Camera Group Adding When adding a device, you can check the Export to group checkbox to export the device you added to certain management group. By default, the name of the group is the same with the name of the device you just added. If you don t want to add the group in this way due to the default name issue. You can click Next page, to enter the adding group interface. Click Save to add a new user. Click Modify to change the settings for the new user.
14 5. Click the Add on Group dialog box. Edit the name of group and then click OK to save your settings. The added group will be displayed in the list. 6. Import Channels to Group In the left area on the Camera Import interface, click to select the channels and then click Import button to import the selected channels to the Group on the right.
15 7. You can drag and select multiple channels to import them to the group you added. Note: The devices to be added must be online currently. Each channel can be added to one group only once, while the one channel can be added to different groups. Up to 256 groups can be added, and 64 channels can be added to each group, with a maximum of 1024 channels for all the groups totally. After importing the selected channels to the group, you can return to the control panel and then enter the Main View interface to get a live view of the added channels.
16 2.5 User Login When you open the ivms-4200 software after registration, the login dialog box pops up, shown in the following figure: Input the user name and password, and then click Login. You can also enable the auto-login by checking the Enable Auto-login checkbox,and then the user name and password is not needed for the login next time.
17 3 Control Panel and Main Menu Bar Introduction The main control panel of the ivms-4200 is shown in the following figure: Menu Bar: File System Open Captured Picture: Open Video File: Open Log File: Exit: Lock: Switch User: System Configuration: Import Configuration File: Export Configuration Enter the setting interface to browse the folder in the host PC of the exported captured picture file (s) and view the captured pictures. Open the video player and browse the folder location of the exported video file (s), click to browse the folder in the host PC of the record files. You can also capture pictures during the playing of the video file. Enter the Log File interface to browse in the host PC of the folder location of the exported log file(s). Exit the ivms-4200 remote client. Lock the screen operation. You must log in after locking the system. Switch login user. Enter the System Configuration interface. Import client configuration file from your computer. Export client configuration file to your computer.
18 File: 1024*768: Display window at size of 1024* *1024: Display window at size of 1280*1024. Full Screen: Display window in full screen. Control Panel: Enter Control Panel. View Main View: Enter Main View interface. E-map: Enter E-map interface. Event Search: Enter Event Search interface. TV Wall: Enter TV Wall Setting interface. Import Camera Enter Import Camera interface. Camera Settings Enter Camera Setting interface. Account Management Enter User Account Management interface. Device Management Enter Device Management interface. Tools Storage Server Enter Storage Server Management interface. Management Stream Media Server Enter Stream Media Server Management interface. Management Decoding Device Enter Decoding Device Management interface. Management Broadcast Select device to start broadcasting. Help Open Wizard Use the guide for camera import. About View information of the client software, including company, software name, version, etc. User Manual (F1) Click to open the User Manual; you can also open the User Manual by pressing FI on your keyboard. There are 14 icons on the control panel, and their functions are described in the following table: Operating Options Main View E-map Event Search Remote Playback TV Wall Import Camera Local Log Search Account Management Device Management Viewing live and playback video; realize video operation (e.g., picture capture, recording, PTZ control, etc.). Managing and displaying E-Map and hot areas and spots; realize E-Map operation (e.g., operate map zoom in/out, view hot spot, display alarm, etc.) Searching and playback of the event record files; realize playback operation. Playback the recorded video and/or audio files in the remote client. Configuring the decoding of the channels and show them on the TV wall. Adding, modifying or removing the camera groups; import/export of cameras. Searching, viewing and backup of local logs (alarm, operation, system logs). Adding, modifying or removing the user account parameters; assign operating permission to each user. Adding, modifying or removing the DVR device; configuring parameters (e.g., network, alarm
19 Management Options Storage Server Management Stream Media Server Decoding Device TV Wall Management input/output, HDD, etc.) for the added DVR. Adding, modifying or removing the storage server; configuring parameters (e.g., record schedule, network, HDD, etc.) for the added storage server. Adding, modifying or removing the stream media server; configuring parameters (e.g., RTSP port, upper/lower limit, etc.) for the added stream media server. Adding, modifying or removing the decoder; configuring parameters (e.g., network, alarm input/output, exception, etc.) for the added decoder. Adding, modifying and deleting the TV wall. Configuration Options Camera Settings Configuring camera parameters (e.g., image quality, record schedule, motion detection, etc.). System Configuration Configuring the general parameters (e.g., saving path of files, alarm sound, , etc.).
20 4 Live View Before you start: A camera group is required to be defined before live view. And the group name is shown on the list in the left bar. Click the main view icon live view interface. on the control panel, or click View -> Main View on the toolbar to enter the The main view interface is shown as in the following figure: Camera Status: Icon Description Camera is online and works properly. Camera is offline. Camera is in live view.
21 Camera is in recording status. Main View Toolbar: Button Name Description Layout Select different layout mode. Full Screen Stop All Manual Record Previous and Next Auto Switch Volume Live Audio Display video in full screen mode, click again to restore. Stop the display of all the cameras. Start manual record for the selected channel, click again to stop. Click to view previous and next camera. Start auto switching the screen by cameras or by groups. Adjust the volume for live audio. Enable/disable live audio. Click the following box pops up, you can choose the screen layout by clicking certain icon.
22 Operations in Live View Start live view for one channel: To view the live video, drag the camera from the list to the display window, or double click the camera name after you select one screen. Start live view for camera group: You can also get the live view for the whole group to display the live view of the cameras in the group in the screen. Click on the group name, and then click the Play button at the bottom of the screen, see the following figure. Or Double click the group name. Toolbar in each display window:
23 Button Capture Description Stop live view: Start manual record, click it again to stop Start voice talk, click again to stop. This two-way audio can be used for only one camera at one time. When you enable the voice talk of one camera, then the voice talk for other camera is stopped. PTZ control, 8 direction icons will be displayed on the video. Check the camera status Go to the camera setting interface Stop live view Remote playback about 7 minutes record of current camera Audio button, click to open and close To stop the live view for one channel, you can click To stop the live view for all the channels, click in the quick setting toolbar. on the bottom bar. Cycle Live View: Cycle live view mode includes the auto-switch in one screen or the auto-switch in multi-screen. 1. Click the next to the. 2. Choose the auto-switch mode and set the interval for the switching. 3. Click on the toolbar on the bottom to start the cycle live view. Capture in Live View Steps: 1. Select the screen. 2. Click icon on the bottom toolbar of Main View, or click icon in the tool bar of this display window.
24 A small window of the captured picture will be displayed to notify you whether the capture is done or not. If the capture is successful, there will be a link to the saving path of the pictures, and if not, there will be error messages accordingly. To view the captured pictures: Click on the small window of the pictures showed on the right bottom after capture. Click the icon on the left toolbar; all the pictures captured on the remote client are stored here. Click File button on the toolbar and select Open Captured File.
ivms-4200 Intelligent Video Management System Quick Start Guide Notices The information in this documentation is subject to change without notice and does not represent any commitment on behalf of HIKVISION.
ivms-4200 Client Software Quick Start Guide Notices The information in this documentation is subject to change without notice and does not represent any commitment on behalf of HIKVISION. HIKVISION disclaims
ivms-4200 Client Software Quick Start Guide UD.6L0202B1538A01 Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact the dealer. This manual applies
ivms-4200 Client Software Technical Specification v1.02 Introduction ivms-4200 Client Software is a centralized video management software using a distributed structure for surveillance device control and
ivms-4200 Client Software User Manual UD.6L0202D1939A01 User Manual COPYRIGHT 2015 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others,
CMS User Manual Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact the dealer. This manual applies to CMS. This manual may contain several technically
ivms-4200 PCNVR User Manual (V1.03) UD.6L0201D1056A01 Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact the dealer. This manual applies to ivms-4200
ivms-4200 Client Software User Manual Hangzhou Hikvision Digital Technology Co., Ltd. Notices The information in this documentation is subject to change without notice and does not represent any commitment
UC2 Video Surveillance Client User Manual V1.0.6 MODIFY STEPS VERSION WRITER STATUS DESCRIPTION DATE V1.0.3 BRIAN A Add access mode function 2011-4-11 V1.0.4 BRIAN A Add PTZ and user role and so on 2011-4-23
ivms-4500 (Android Tablet) Mobile Client Software User Manual (V3.0) Thank you for purchasing our product. This manual applies to ivms-4500 (Android Tablet) mobile client software; please read it carefully
User Manual (V2.0) Thank you for purchasing our product. This manual applies to Local Playback software, please read it carefully for the better use of this software. The contents in this manual are subject
ivms-5200 Professional Web Manager User Manual UD.6L0202D1651A01 Hikvision ivms-5200 Professional Web Manager User Manual This manual, as well as the software described in it, is furnished under license
User s Manual of DVR DVS Remote Client Software V 4.0.1 Index Version description...4 1 Introduction...8 2 Software Install, Uninstall and use...9 2.1 Install remote client software ver4.0.1...9 2.2 Uninstall
Professional Surveillance System User s Manual \ 1 Content Welcome...4 1 Feature...5 2 Installation...6 2.1 Environment...6 2.2 Installation...6 2.3 Un-installation...8 3 Main Window...9 3.1 Interface...9
ALIBI Central Management System (ACMS) Software User Manual Products: All ALIBI DVRs, NVRs and IP Cameras PLEASE READ THIS MANUAL BEFORE USING THIS SOFTWARE, and always follow the instructions for safety
Network Video Monitor Software V22.214.171.124 Operation menu Chapter 1 Product Overview 1.1 Performance instruction Network video monitoring software is a centralized management tool for I8 protocol surveillance
ivms-4500 (Android) Mobile Client Software User Manual (V3.1) UD.6L0202D1111A01 Thank you for purchasing our product. This manual applies to ivms-4500 (Android) V3.1 mobile client software; please read
ivms-4500(windows Mobile) Mobile Client Software User Manual Version 1.0 Thank you for purchasing our product. This manual applies to ivms-4500 (Windows Mobile) mobile client software, please read it carefully
Pro Surveillance System 4.0 Quick Start Reference Guide 1 Table of Contents 1) Overview 3 2) Initial Setup Adding a Connection..4 3) Viewing Live Cameras...6 4) Single or Multi Channel Playback..8 5) Predetermined
A quick user guide for your LX Apollo DVR The LX Apollo series of DVR s is designed specially for the security and surveillance field and is an outstanding digital surveillance product. It has an embedded
idvr-pro Viewer Software for Mac User Manual ver 0.1 1 Contents 1. Introduction... Error! Bookmark not defined. 1.1 Summary... Error! Bookmark not defined. 2. Install... Error! Bookmark not defined. 2.1
ACS CLIENT SOFTWARE USER MANUAL 1 ACS USER GUIDE 1.1 System Requirement Recommended System Requirement OS CPU VGA RAM HDD WindowXP, Vista Pentium 4, 2Ghz 1024*768, 64MB 24bit color graphic card 1GB 20MB
i -CEN S i -CEN'S USER S Manual 2007. 08. 13. i -CEN S Table of Contents Overview of i-cen S software... 4 1 Introduction of i-cen S... 4 2 Key Features... 5 3 Key Benefits... 5 4 System Specification...
ivms-4500 (iphone) Mobile Client Software User Manual (V3.1) UD.6L0202D1029A01 Thank you for purchasing our product. This manual applies to ivms-4500 (iphone) mobile client software; please read it carefully
User Manual V1.0 Notice: The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change
Central Management System (CMS) USER MANUAL LEGAL INFORMATION Reproduction, transfer, distribution or storage of part or all of the contents in this document in any form without the prior written permission
IPC Video Surveillance Client User Manual V1.1.2 Statement Thank you for purchasing our products! If you have any questions or need, please contact the customer department at any time. This manual applies
Professional Surveillance System User s Manual Version 4.06 Table of Contents 1 OVERVIEW AND ENVIRONMENT... 1 1.1 Overview...1 1.2 Environment...1 2 INSTALLATION AND UPGRADE... 2 2.1 Installation...2 2.2
Table of Contents Chapter 1. User Interface Overview...5 Chapter 2. Installation...6 2.1 Beginning Installation...6 2.2 Starting the CMS software...10 2.3 Starting it from the Start menu...10 2.4 Starting
ivms-4500 HD (ios) Mobile Client Software User Manual (V3.4) UD.6L0202D1587A01 Thank you for purchasing our product. This manual applies to ivms-4500 HD (ios) mobile client software; please read it carefully
Remote Backup Software User Manual UD.6L0202D1044A01 Thank you for purchasing our product. This manual applies to Remote Backup software, please read it carefully for the better use of this software. The
Network Video Monitor Software V126.96.36.199 Operation menu Chapter 1 Product Overview 1.1 Performance instruction Network video monitoring software is a centralized management software for I8 protocol surveillance
Quick Start Guide NVR DS-7104NI-SL/W NVR NOTE: For more detailed information, refer to the User s Manual on the CD-ROM. You must use your PC or MAC to access the files. www.hikvision.com Quick Start 1.
Manual Client Management Software HDR50-CMS HDR50-CMS (Client Management Software) A-1. Install HDR50-CMS for Windows PC HDR50-CMS is a program for communication between DVR and PC to control signal and
ADTVision (ios) Mobile Client Software User Manual (V1.6) Thank you for purchasing our product. This manual applies to ADTVision (ios) mobile client software, please read it carefully for the better use
LOREX CLIENT Remote Software 4.0 Instruction Manual English Version 2.0 MODEL: L20WD800 Series www.lorexcctv.com Copyright 2008 LOREX Technology Inc. Table of Contents Table of Contents Software Installation...
ACTi Central Management System User s Manual Version 1.1.05.06 2012/10/12 Table of Contents 1 Overview 5 Software Architecture... 5 2 Installation 6 Requirements... 6 Operating System... 6 Hardware System
ivms-4500(android) Mobile Client Software User Manual (V1.0) Thank you for purchasing our product. This manual applies to ivms-4500 (Android) mobile client software, please read it carefully for the better
Network Video Recorder Quick Operation Guide UD.6L0202B1119A01 Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. This manual is applicable
ivms-4500(iphone) Mobile Client Software User Manual (V1.0) Thank you for purchasing our product. This manual applies to ivms-4500 (iphone) mobile client software, please read it carefully for the better
SMS (Server Management Software) Digital Video Recorder User s Manual Contents 1 - Introduction 2 1.1 About this manual 2 1.2 Configuration 2 1.3 SMS Functions 2 1.4 Product Information 2 1.5 System Requirements
Appendix A. CMS(Client Management Software) A-1. Install CMS for Windows PC CMS is a program for communication between DVR and PC to control signal and video. Insert the enclosed CD, and go to CD-ROM Drive
NetClient software user manual 1-1. General information Net Client is an application which provides users not only viewing and controling remote DVRs, but also receiving realtime event data or alarm signals
DVS Net (Integration) Installation and User s Guide Ver 11.10.x Digital Video Security System Digital Video Recorder www.tuniss.com PLEASE CALL TUNISS COMPUTER AT: 650-401-6138 FOR ANY QUASTIONS REGARDING
Quick-Start Guide SUPER DVR MONITORING SOFTWARE Remote Surveillance & Playback For use on Q-See s QSDT series of PC Securitiy Surveillance Cards 2 CONFIGURING ROUTER FOR REMOTE ACCESS REMOTE SURVEILLANCE
DIGICLIENT 8.0 Remote Agent Software MODEL: D17800 Series Instruction Manual English Version 1.0 Copyright 2007 Digimerge Technologies Inc Table of Contents Table of Contents About the DigiClient 8.0...
User Manual IP Camera For further help, please visit www.zmodo.com 1 Preface Preface Dear customer, Thank you for purchasing our products. If there are any questions, or requests, please do not hesitate
User Manual of Web Client 1 Index Chapter 1 Software Installation... 3 Chapter 2 Begin to Use... 5 2.1 Login and Exit... 5 2.2 Preview Interface Instruction... 6 2.3 Preview Image... 7 Chapter 3 Playback...
Remote Client / Web Client USER MANUAL T Series Digital Video Recorder Remote Client Program... 3 Remote Client Program Installation... 4 Remote Client... 6 Main Window... 6 Site Registration... 7 Group
Smart Professional Surveillance System User s Manual Version 1.10.0 Table of Contents 1 OVERVIEW AND ENVIRONMENT... 1 1.1 Overview... 1 1.2 Performance... 1 1.3 Environments... 1 2 INSTALLATION AND UPGRADE...
DVR4x4RemoteViewer.book Page 3 Tuesday, February 15, 2005 9:19 AM DVR4C Remote Viewer Operation Manual Table of Contents EN 3 1. OVERVIEW...5 1.1 MINIMUM PC REQUIREMENTS...5 2. INSTALLING THE PROGRAM...5
ivms-4500 HD (Android) Mobile Client Software User Manual (V3.4) UD.6L0202D1597A01 Thank you for purchasing our product. This manual applies to ivms-4500 HD (Android) mobile client software; please read
Instruction for IE network monitor This system features a built-in browser-based software that allows you to access your system remotely over your local area network (LAN) or over the Internet (WAN) using
ivms-4500 (ios) Mobile Client Software User Manual (V4.2) UD.6L0202D2114A01 COPYRIGHT 2015 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among
Introduction How to Configure Alarm Notification Alarm notification function makes ivms-4500 a professional and powerful private security guard for 7X24 surveillance. Once there are events occurring, notification
SMS Remote Software User Manual Pro Series & Contender Series DVRs Table of Contents Chapter 1 Overview 1 1.1 In This Manual 1 1.2 Overview 1 1.3 SMS Features 1 1.4 Product Information 1 1.5 System Requirements