MODEL: DV72 R & L. Mechanical Ventilation with Heat Recovery Installation Instructions and User Manual

Transcription

1 / / : ; / < 0 3 < 1 MODEL: DV72 R & L Mechanical Ventilation with Heat Recovery Installation Instructions and User Manual Commissioning Data: to be completed by the installer Date of installation: " Configuration Left Hand Right! Hand # $ Product Serial No: % & ' ( ) * & & +, & -. - $ Important: This multi speed unit required Air Flow Rates to be adjusted when system is commissioned. " - '. " This manual must be kept by the householder 1

2 X P Q Q Index Page = >? > A A > B C A D E? F? G H General Information 3 I J >? K > L >? M About the Unit 4 N > L? F? G E L F O O J Wiring Diagram 5 Technical Specifications 6 R? E S O A A O S F B? E T > U A > L? F? G V W X P Installation Instructions 7-15 R Z G S O G? F? G Commissioning 16 [ U > \ A F E S > X V Check List 17 ] > L A F G > K B A L > A E > X ^ W X _ Maintenance ` a b O C C >? L F \ E c S > E > E Z A S O S d e W d d SAP Appendix Q Testing Results I T >? E E S > J J > A E > E \ A F? G d H Declaration of Conformity 23 = O? S F d M Warranty 24 2

3 ! p General Information g ", -. & $ To ' + maintain & a healthy - indoor - environment, - closely h controlled - ventilation ' is essential. & There i j k are * many l pollutants * + that - will affect - - the $ indoor air ) quality: - - ' human ' body waste & products - in & the shape *. of - CO - 2, * dead - skin, perspiration., - - & and moisture. - ' Add to this the ) waste, $ products of cooking (cooking smells), showering (moisture), gases from building materials and the waste products of pets. m - - ' ) & " & & & ' * & Without proper ventilation this would be the perfect environment for the growth of mould, - " & & -.. $ subsequent damage to the decoration and fabric of a home and to the health of its occupants. g & & - -, & g i (. ) & The Heat Recovery unit is fitted with two, low energy EC fans with a constant (100% adjustable) air. l & -. $ volume. n o o q r s t t * & * ) ' + & The & - exhaust $ fan - ensures that warm, damp & and polluted * + air as & near - as possible - to the source is extracted. The exhausted - -. ) air has * & to be replaced - +, with & fresh air, u v so w the heat r s recovery t unit not only has an exhaust fan, but is also fitted with a supply fan and air filters. x, - * & & * ' & The supply air, which in winter is colder than the inside air, is heated in the heat recovery unit using & - - " ) ' & - - & & $ the heat of the exhaust air by means of the heat exchanger. This heat exchanger has a maximum & & & ' + y * + & & & &. efficiency of 91%, so a minimum loss of heat takes place n p and the supply air temperature enters the & * -, - & ' & & ' + &. $ home at a comfortable level. z ) - " " & -, ' + - In exceptionally cold weather or winter conditions it is possible that the exchanger may freeze due & & *, ' $ g ' l ' + u v u $ to sub-zero, cold incoming air. Therefore the unit must be sited in a frost-free location. { & ' ' -. -., & & $ Alternatively, an in-duct heater may be used to protect the heat exchanger from freezing. x * * & * * + & &. - $ The filters in the unit ensure that the fresh supply air is clean as it enters the home. Also, the extract air from the property is filtered to protect the heat exchanger from unwanted contamination. These filters must be inspected regularly, initially every month, and cleaned. Each property will contaminate the filters at a different rate. The filters should be replaced annually or after a maximum -, of & two cleaning $ cycles. Regular filter maintenance will ensure the integrity and performance of the unit. The unit s condensate drain must be installed and connected to the household drainage system., - - $ and must be insulated if installed outside the insulated envelope of the building, & ' - & ' & & + - * If the ductwork passes through an unheated area (loft or similar location), it must be insulated with & - & *., & $ an insulation material that complies with the latest Building Regulations. } q ~ ~ ~ u v t t t t t t t t r v t r u ƒ t r t u v t t t DO NOT switch off the unit it is designed to run continuously. If the unit is switched off, s t u t u v t u v t v u t t t t ƒ ˆ t t indoor pollutants and moisture levels may increase which could endanger your health or t v t ƒ damage your home. Š t t t t Œ t r u s r t u t r r t t t t s t In the event of a power failure or the unit being turned off, restart the unit at High Speed. r t ƒ ˆ t t % Ž t t t r ƒ This MVHR unit has a soft start. ˆ t t u r t t t t t t r t v t r t v r t w t t v t ƒ It is important to follow the advice in this user manual and correctly maintain the system to ˆ t t t r t t t r ƒ ensure a healthy indoor environment. 3

4 About The Unit Z C A > T >? S ] V d N \ B J C A > S S > T J > G >? F? L T F? L F? G E >? K > L L G B C S F J O A Duplexvent DV72 R & L are complete heat recovery > > \ S F T F S > S S F A L F S K U > J units to ensure optimum efficiency for your home.? K > L > \ B J J F T >? E > W B G K > T >? L S > T E F B? The units are supplied as left or right hand options. ` > E F L > X X See page 11 T >? K > L A > T > E J > L > S E S O? L L T f G J B? S F? G E E f S Standard wall mounting kit is supplied with each unit. ` > E F L > _ W X d J B? S F? G > S B G E š J Z A F G S O S J B? S > For fitting see page Optional horizontal floor >? K > L >? T O? > S C š G Z A T > S mounting is also available. ` > E F L > X H W X P See pages The? K > units L > are A > T > > E E B J E as S O? standard L L J > L with: B E S Y > E \ D S S > A E > Y B B E S W Z? \ S F B? S J F E \ Y D C O E E B G Frost protection, boost function, thermal bypass and U E S F? G E C O? > A remote commissioning panel. Mounting Wall Monteringsplade plate Vægbeslag bracket SPRÆNGSKITSE EXPLODED VIEW Spigot Studs Varmegenindvindingscelle Heat recovery Afstandsstykker Spacers Fikseringsstænger Fixing rods Frontpanel cover Motorsamling assembly Frontlåg shell Drain Filter & Filter plugs Remote Fjernbetjening control 4

5 ž Ÿ Ÿ ª ª Ÿ «± Ó µ Ô Ê É µ º Å È Î µ Æ À  µ º É Ê É µ È Î µ Æ ² ³ µ ¹ º» ¼ ½ ¾» À ³ Á  º µ Ã Ä Å Ã Æ Â Æ Ç È º É É Ê É µ Ë Æ Ì Í µ Ë Î Â Ê É Ï Ð Ñ Ò ² Ã Ä ± È Æ Î µ Æ µ Ã Ä ¾ ³ ¾ ³ Õ Ö µ Ô Ê É Ï Ð Ñ Ò Õ Ö µ Ô Ê É ³ Í µ Ë Î Â Ê É Ò Å Ê ± ± Ó µ ¹ Ô Ë µ µ ¼ Ã Â Ó Â ± È Æ Õ Ö ¾ Ê ± Ø ÙÚ Û Ü Ý Û Þß à á Ù â ã ä å æ ç è ß é Ù ê å ë è Û ì Ý í î æ ï ð ñ è ò ó Þô Ø õ Ü Ý à Ü Û Þß à á Ùõ á ö Ü Ù Ø Ùø ù ú û ô ü ý Þì ÙÜ í þ Ø Ý é à ÿ â ì Ý í ê ð ó Þô é Ù è ä Ý û à Æ ± ʵ ± ± È Ê Æ < ; : ; : ; ; ; ; ; ; < ; ; ; : ; 9 ; ; 8 ; ;! ; ; 9 " " 9 9 " 9 ; # 0 $ % 1 0 & ' ; ; 9 ; ; 7 ; 8 " ( # 9 " ; ; # " " 9 9 ; 9 : ; ) 7 ; * 8 ; + ; 7 ; 9 ; ; ; 7 ; 7,, ; " ; ; 7 ; " ( # * 0. + ; 7 ; ; ; 7 ; < * * / 5 ; ; 9, ; ) ;, ; ) ; 8-8! ; ; 9 ; * 9 ; 8 ; ; 9, ; 9-8 ; ; ; 9 ; ; 8 : ; ( 9 8 ; ; ; ; ; " ( ; + ; 7 ; 0 / 5 ; ; 8 9 9, ; 5 0 * 1 5 ; 9 ; 2 3 ± Æ Æ µ ÊÉ ± È Æ 4 Ø Ùø ù è ú û ô ü è ý Þì ÙÜ í þ è Ø Ý é à ÿ è â ì Ý í ê è ð ó Þô è ä é Ù è ä Ý û à E ž ª Ÿ F G Ÿ ž G « : ; 6 < = > 8 ; 6 A ; B?6 A B C >; : 6 = 9 D H «I Ÿ ª Ÿ J K F L Ÿ ª M ª ž K K K ª ª J Ÿ Ÿ ª N O P H Q R S «T «U V ª L ž J Ÿ ž W ª Ÿ ª Ÿ ª X J G X ª X V ª ª V F L Ÿ ª Ÿ L Y K M V ª F Ÿ ž W ª Ÿ O L X Ÿ F Ÿ G ª Ÿ ª V J ª V L Ÿ Z L ª V ª «P «[ G Ÿ ž G \ ] ^ ` Z W Ÿ K L Ÿ L Z Ÿ Ÿ V F L Ÿ a K Ÿ F L K F Ÿ O X Z L Ÿ V ž Z Y b Z Ÿ F L Z Ÿ V Ÿ Z Z Ÿ K Ÿ F «c > L A Z \? F? G F? L E F S Z O S F B? W >? K > L >? E \ O A F E B A > E

6 h g p d f n o #! o o o p p s g g r o & & Technical Specifications h & & - - d e f & h f h { i j k l, z # m Maximum Flow Rate 75 l/s (270m g 3 /h) MAX* Protection Class IPX2 & Heat Exchanger l ) Fans j &, - Electrical Supply & ' & Counter Flow (Plastic) n y Thermal Efficiency n p 91% g i g l l, EC (Electronically i & & i Commutated DC) f e 230V/1PH/50Hz o o! q j Spigot Ø h + e r G3 G3 e & & 125mm n g r p e 560 o x s 635 x 260mm h $. - ) - - Max Power Consumption 140W n t o u Weight 14kg n t Supply Filter Extract Filter Dimensions v w x y z z { } ~ ƒ ˆ Š Duplexvent Static Pressure - Airflow Ž Œ 8 š œ ž Ÿ ž 6

7 Installation Instructions IMPORTANT Be sure to have read and understood these instructions before beginning the installation process. PRE-INSTALLATION CHECK LIST Make sure that the unit can physically fit in to the desired location. The Duplexvent unit should be situated so that access for maintenance or replacement of parts and filters is possible. The Duplexvent unit is suitable for conventional rigid ducting or low energy radial duct system Airflow Development Airflex Pro system. If using conventional ducting ensure duct runs are as short as possible, having the most direct route and using as few bends as possible. This is to reduce system pressure. SAFETY AND RECOMMENDATIONS All wiring must comply with Building Regulations and the current I.E.E. Wiring Regulations (BS7671) or the equivalent standards for your country. The final installation should be examined and tested by a qualified electrician. Precautions must be taken to avoid the back-flow of gases into the dwelling from the open flue of gas or other fuel-burning appliances. Make sure the mains supply complies with the rating label for voltage, frequency and phase. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. If any cables are damaged they must be replaced by the manufacturer, its service agent or similarly qualified persons 7

8 Installation Instructions Control Options B E S Y > E \ D S S > A E > Frost Protection c >? K > L >? E > A A > S > J C O S O A L S F A Z? L When H Bthe C T O J temperature >? K > L >? O Zin S B the J O S F E unit \ > falls A A >? below J > L Z L 3ºC E Z G > the S A Z unit S automatically O S K F? > L warms O?? > A E > the O B E S with extracted air to prevent the formation of frost. When the cell temperature in the unit falls Boost - Switched Live When The unit the comes cell with temperature Switched in Live the as unit falls N F T > > S >? O Z S B J O S F E \ Z? \ S F B? L E f S S standard. It is an automatic function, sending Boost >? K > L the unit -> Switched? S F A Y B B E S to boost when Live? A D E > S F Y O L > T > A E > S > A A the bathroom or kitchen \ \ \ >? > S S f? L S > A A K T F E Y B B E S W \ B? S O \ S >? light is on, or boost switch is activated. The E A š unit > S S comes F A with Switched Live as Summer ` B J J Y Bypass D C O E E Boost - Switched Live The ` B J J summer Y D C O E E bypass K U f A C > S F A reduce J > L the O S The air? > L E temperature unit comes with f S S > L >? S coming Switched > J C O S Z into L the as dwelling Summer \ B J J during F? L F the Bypass Y B A summer F G >? F months. E B J J JIt š is? > an L > > > S function >? O and Z S B J Ooperates S F E \ Z? \ when S F B? L the supply air The temperature summer E D? F? G E A Z S to S > the bypass J C > property O S >? S is F A > above reduce U >? L B J 25ºC. the J >? Summer B T d P Bypass The summer bypass helps reduce the ª «ª «ª ± ² Control Options ³ «² µ ««² ² Frost Protection Boost Switched Live ² µ ¹ º Thermal Bypass 8

9 Installation Instructions FIRST FIX - Installing ductwork and electrical supply Important note: This unit is for wall or floor mount only. Ceiling mounting unit are configured differently and should be ordered separately. 1. Locate external terminations (supply and extract) in accordance with the latest addition of the Domestic Ventilation Compliance Guide. 2. Ductwork from the unit is Ø125mm dia. - maximise duct size where possible. Make sure that the ductwork is insulated in unheated spaces. Minimise flexible duct. 3. Locate the mains supply within 1m of the location of unit. The position of the electrical power supply or unit (a fused switched isolator) must not be mounted above or closer than 1m to a cooker where it could be affected by excessive heat or moisture. 4. Make sure that there is room for the MVHR unit. The unit is designed to be wall mounted. It can also be floor mounted with an additional kit. Part number Also make sure that there is a free space at the front of the appliance for cleaning the filter and carrying out maintenance on the appliance. Ducting Configuration See page for duct connections to the unit/air flow directions» ¼ ½ ¾ ¼ À Á Â Á Ã Ä Ã À Å Æ Radial Duct System Installed example, RH unit shown. A No exhaust within 2m of air inlet B Inlet duct from atmosphere C Outlet duct to atmosphere D MVHR E Ducts to and from property F Condense Drain Note: Important if installed in a loft space the area should be within the insulated envelope to maintain optimum performance 9

10 Installation Instructions SECOND FIX Installing Vertically Hung unit 1. Attach the wall bracket to a flat stable surface that is capable of bearing the unit s weight, 12Kg. Ensure that the bracket is positioned so that there is enough space for the condensate drain and ducts to be connected. Fixing kit provided. Raw 3. Slide the unit onto the wall bracket and attach ducting and drain. Pre fixed bracket on the back of the Duplexvent unit Wall bracket Screws x 5 Connect 22mm PVC drain fitting 2. Attach spacers x 2 with screws provided. The spacers ensure that the unit tilts forward to improve drainage. Use the tie down cable if required to secured the bottom of the unit. Anti Vibration Mount Foam casing 4. The drainage from the unit may be connected to an internal waste water system or soil pipe with an appropriate non-return device. One way valve device is recommended. Insulate pipes in an unheated loft space. Ç À ¼ È ½ ¼ Á ½ É Ê È À Á ¼ Ë Å È À ¾ Å È Ì Å ½ Í Ÿ J Ÿ E ZWall W Kfit L only Ÿ ˆ Î ~ 10

11 Installation Instructions SECOND FIX installing Vertically Hung Unit Airflow and drain fitting - LH Airflow and drain fitting - RH To atmosphere From atmosphere Extract from dwelling Supply to dwelling Supply to dwelling Extract from dwelling From atmosphere To atmosphere Ï Ð ± ª «² ª ± Ñ Ï Ð ± ª «² ª ± Ñ Wall Wall mount mount Drains are factory fitted. The units has either a LH or RH drain. 11

12 Wall mounting bracket dimensions Please note that there is only one loose bracket with the two tab bracket factory fitted. Ò Ó Ô Ô Õ Ö Õ Ø Ù Ø Ú Û Ú Ü Ý Þ Ö Ó Þ ß Ú à á Õ Ô Ù â 12

13 Horizontal mounting bracket dimensions 13

14 ã Installation Instructions SECOND FIX Installing Horizontal Mounted Unit Connect 22mm PVC drain fitting Floor mounting 6. Mount the remote control near the unit. Fix securely to a flat surface. For 5. The unit can be floor mounted by using the horizontal mounting kit, Part Number Use the long and short S brackets provided along with short fitting screws to ensure correct drainage. The unit must be higher at the duct end. Bracket fixing position. See Page 13 maintenance please ensure the remote control is disconnected before removing the unit from the wall. X2 X2 Drain connections should be solvent welded as here. The center Tee section is reversed to make either LH or RH drain. Push in the drain fitting and seal as appropriate to create a watertight assembly. ä å æ ç è ç é ê ë RH When fixing the remote control please ensure the ribbon cable is in place (contacts down, red side up) up). ì ç é í ë æ ç è ç é ê ë LH Important note: The floor mounted drain must be fitted on the same side as the factory fitted drain. This unit is for wall or floor mount only. Ceiling mounting units are configured differently and should be ordered separately. 14

15 Installation Instructions SECOND FIX - Drainage for floor mounted units Floor mount - LH drain Floor mount - RH drain î ï ð ñ ë ò ó í ô õ æ ç é To atmosphere ö ê í ø é ï é ø ô æ ñ ù ó ð ï ø Extract from dwelling ú æ ñ ñ ë ò ó í ô õ æ ç é From atmosphere ú ó æ í û é ï é ø ë ï ð ù ó ð ï ø Supply to dwelling î ï ð ñ ë ò ó í ô õ æ ç é To atmosphere ö ê í ø é ï é ø ô æ ñ ù ó ð ï ø Extract from dwelling ú æ ñ ñ ë ò ó í ô õ æ ç é From atmosphere ú ó æ í û é ï é ø ë ï ð ù ó ð ï ø Supply to dwelling ü ç ê ô ä ð ø ç é ê ç ý æ ó ý ë Place ï ð ê ç ë ò stopper ó é ë ç æ ç ê ç provided into the fitted drain ü ç ê ô ä ð ø ç é ê ç ý æ ó ý ë Place ï ð ê ç ë ò stopper ó é ë ç æ ç ê ç provided into the fitted drain Ø20mm Saw Ø20mm Saw þ ó æ ï é ê ï ÿ ñ ù ï é ç ë ë ç ë í ó ò è ï í ë è ç ê ñ ë ù æ ø ç ò ç ë ñ ð ý ð ñ ê ç é í ó ò Drill into the case as shown, using the metal plate ç é ø ï ê ç ä æ ø ô ó æ ñ ë í ÿ ò ÿ ç æ é ç é ç æ ç ð ë ô å ç æ é ç ë as a guide. Ensure that the foam core is fully removed. 15

16 Commissioning Setup guide for the Duplexvent The commissioning panel is found on the the remote switch. Commissioning mode is chosen by pressing the SET button for 4 seconds, all sensor inputs will be disabled in this mode so that they do not interfere with flow rates. All LEDs will light with the Extract Boost flashing (Ext B), this indicates that the flow rate may now be increased/decreased as required. The next press of the SET button will move commissioning to the next setting, Sup.B and so on. When the unit has been fully commissioned, press the SET button for 4 seconds and this will put the unit back into status mode. If the unit is not put back into status mode after commissioning, it will automatically revert back to status mode after an hour. Note: Settings will be retained if the power supply is interrupted. IBRUGTAGNING Constant LED! ³ «² µ ««² ² ' ( (A) Frost protection ON &! & «) ««º ª ) (B) * Boost + ± «±, state ² - ' ( Humidity ON -! & «) ««º ª ) (C) «Boost µ ² state «ª ¹ - + «' ( switched input ON.! " ² ) ¹ º (D) ' ( Summer by-pass ON LED Indications Flashing LED ª % # ² ª ± (A) Service required &! " ² # $ ² (B) Service required ª % # ² ª ± Supply and extract LED indications Commissioning mode only! " ² # $ ² 16

17 Checklist Installation instructions have been understood Ducting Ø125mm or larger has been used from the unit The unit is securely fixed into position with enough space left for servicing Condense drain is tight, drains to a suitable location and has been water tested 17

18 Maintenance Pack of 2 x filters. Part number Filter cover Front cover General advice: Regular filter inspection is recommended. Minimum recommendation is to check filters every 6 months. Some installations will need more frequent filter inspection to ensure maximum efficiency of unit. Filter Maintenance recommendation: Switch off the power supply Remove front panel Remove filter covers Remove the filters Vacuum the outside of the filter or replace if required After cleaning replace filters at same side Replace filter covers and front panel Major service: This is to be carried out every five years (minimum) by an approved maintenance company. 18

19 Maintenance Disassembly of unit for engineering access and maintenance: 1. Remove the velcro pads. front cover...held on with 3. Carefully remove the top foam moulding by pulling it straight forward. Foam mouldings must remain parallel. Take care gaskets. not to damage the sealing 2. Remove retaining screws and washers x 4, store safely. Do not pull from one edge as this may damage the internal fixing rods. When reassembling the unit should be, after maintenance, ensure there are no trapped wires and that seals are intact. 19

20 ƒ SAP Appendix Q Testing Results Central mechanical supply and exhaust ventilation system packages with heat recovery used in a single dwelling / : 9 ; < = Brand Name Airflow 2 A B 7 C D E F G E H 9 B I J K L M N B I J K 6 Model Duplexvent DV72R and DV72L Model Qualifier (if applicable) O 0 Q R Name Airflow Developments Ltd Lancaster 6 [ H \ [ : 9 E ; LRoad M [ ] ^ ; E : : E F _ 7 : ` H E : : a [ ; b O P Q S P T 2 R U? V 1 2 X X 2 Cressex Business Park Current Manufacturer Address c ` N d e f \ M = g E 5? R U 0 5 U? S A W X R Y R V 2 1 High Wycombe and Contact Details c a h K i j a HP12 3QP k 2 A 2 l? R m n h o p o q K q K q K Telephone r 2 s X Y U 2 Website t S 1 Y 2 A Y V S P T 2 R U u d G ` : 8 M ; : b E D D ` N v Original Manufacturer (if different) w x 1 X U 2 S P 5 U Y? R X y 1 K n h q First Year of Manufacture 2015 z X U 2 S P 5 U Y? R X y 1 Last Year of Manufacture k 2 X U? 1 V 0 R _ L { Testing Body BRE 0 U? l? 1 U 2 X U K K } n i } K n h n Date of test 22/03/2010 z 2 1 Y 2 R P l? 2 U U 2 X U 2 S P 5 U q J ~ n { ^ Serial Number of Product Tested 5780 EC > / U Y A Q 2 Y V 1 Y X U 1 x 1 U W S 2 1? V h q n M N h K q = = ] ` [ = E 9 E ; : 9 ` G C D [ : 9 M N K n n = = X 150 & 125 mm diameter rigid plastic and MVHR U x A X to 2 outside grille duct types and size ] ` [ = E 9 E ; : 9 ` G C D [ : mm diameter rigid plastic x 1 U W S 2 1? V X U x A X 2 0 R Q 2 U U Y A l? 1 X W R Y R V h q n M N h K q = = ] ` [ = E 9 E ; : 9 ` G C D [ : 9 M N K n n = = Duct types and sizes used for supply and 150 & 125 mm diameter rigid plastic and? V X P V R Y R V ] ` [ = E 9 E ; : 9 ` G C D [ : 9 exhaust 200 mm diameter rigid plastic 2 X P A U 0 U 2 1 l? 1 A V 2 U 2 X U Results of leakage tests k 0 s 2 A Table Q1 R U 2 1 R U 2 X U y 2 U 5 X U 2 1 R U 2 X U y 2 U Internal Pass External Pass 20

21 o h K i q v E 2 X P A U 0 U l? 1 z Z ˆ s V R Y R V 2 1 Q 3 Y R Y 3 P 3 l A x s X Š 0 X U Y V Š X l? 1 Š? Results for SAP calculations (at minimum flow rate condition) B E 9 9 E C ; M ] 7 b 9 E ; b 7 H 9 E : 9 E 9 = E ] : 9 ` G E ; < ; Œ M N ] [ 9 [ E H E N D ] E ; ` b b E 8 M ; Ž a g E ; E N H ` H N E ; d G ` : This product has only been tested with rigid ductwork and the data are not applicable for SAP calculations if installed with flexible ductwork. k 0 s 2 A Ž f : 9 E = E ; 7 ] E D 7 b b E H ] E = E ] X U Y Q 2 ; < ; Table Q2 Systems with rigid ductwork only Specific ] : 7 N H ` H N : 9 E ; = ` H [ _ D : E g D : E ; Exhaust terminal Fan speed fan ; d [ : 9 ` N d E E 8 8 E b 9 configuration setting power ] : ` H ] : 9 ` D D ` H N u e } D } : v (W/l/s) < b b E H Kitchen + f ] E ; D ` N E ; E 1 additional wet G ] ; 7 = room < b b E H Kitchen + f ] E ; D ` N E ; E 2 additional wet G ] ; 7 = rooms < b b E H Kitchen + f ] E ; D ` N E ; E 3 additional wet G ] ; 7 = rooms < b b E H Kitchen + f ] E ; D ` N E ; E 4 additional wet G ] ; 7 = rooms < b b E H Kitchen + f ] E ; D ` N E ; E 5 additional wet G ] ; 7 = rooms h n n G 100% [ ; ` [ g E D Variable h n n 100% I [ ; ` [ g D E Variable h n n I 100% [ ; ` [ g D E Variable h n n I 100% [ ; ` [ g D E Variable h n n 100% I [ ; ` [ g D E Variable I [ ; = Heat 7 ] : b ` 8 9 H ` H N exchange E 8 8 E b 9 ` G ` 9 E 9 efficiency u (%) { H E ; N ` g E : C [ ; E H ] E Energy Saving ` d E H d M D ] 9 ` D Trust Best Practice g E ] : 9 E C ; [ b : ` : 8 ; [ Performance { H E ; N ` : 9 f ; E D : E H Compliant Yes Yes Yes Yes No B ` : : E 9 [ D ` H ] : 9 9 E : ` E H 9 E H These figures are entered into either: (a) In the case of SAP software amended to SAP 2005 version 9.81 allowing direct entry of MVHR data, the SAP software, or (b) In the case of SAP software amended to SAP 2005 version 9.81 not allowing direct entry of MVHR I c L ] [ 9 [ Œ Ž a j I c L g E ; E N H ` H N : ; E N H E [ ; b E 9 G p ~ h M N ; E : 7 D 9 [ 9 E ; H E 8 ; [ ; E N H E [ ; b E 9 9 ` D : ; D ` N E data, the SAP Q MVHR Calculation Spreadsheet v9.81 and the results from the spreadsheet into the Special Features part of the SAP 9.81 software, or (c) In the case of SAP software to SAP 2005 version 9.80, the SAP Q MVHR Calculation Spreadsheet v9.80 š and the results from the spreadsheet into the Special Features part of the SAP 9.80 software. œ ž Ÿ They must NOT be entered directly into SAP 2005 version 9.80 software 21

22 v E ] : 7 N H ` H N : 9 E ; = ` H [ Exhaust terminal configuration < b b E H Kitchen h f ] E ; D ` N + E ; E G ] ; 7 = 1 additional wet room û í ë ç ò ç æ ê ç ð ÿ ÿ ç é ê ç ò ç ê Table Q3 Systems with flexible ductwork only æ ä æ _ D : E ; Fan d [ : 9 `speed N d E ] : ` H setting ] : 9 ` D D ` H N Specific g D : E ; E 8 8 E b 9 fan power u e } } : v (W/l/s) I [ ; = 7 ] : Heat b ` 8 9 H ` H N exchange E 8 8 E b 9 ` G ` 9 E 9 efficiency u (%) { H E ; N ` g E : C [ Energy Saving ; E H ] E ` d E H d M D ] Trust Best 9 ` D g E ] : 9 E Practice C ; [ b : ` : 8 ; [ Performance { H E ; N ` : 9 f ; E Compliant D : E H N/A N/A N/A N/A B ` : : E 9 [ D ` H ] : 9 9 E : ` E H 9 E H These figures are entered into either: (a) In the case of SAP software amended to SAP 2005 version 9.81 allowing direct entry of MVHR data, the SAP software, or (b) In I the c L case ] [ 9 [ of Œ Ž SAP a j software I c L g amended E ; E N H ` H N : to ; E SAP N H E [ ; 2005 b E 9 G pversion ~ h M N 9.81 ; E : 7 D 9 not [ 9 E ; allowing H E 8 ; [ ; E direct N H E [ ; bentry E 9 9 ` D of : MVHR ; D ` N E data, the SAP Q MVHR Calculation Spreadsheet v9.81 and the results from the spreadsheet into the Special Features part of the SAP 9.81 software, or (c) In the case of SAP software to SAP 2005 version 9.80, the SAP Q MVHR Calculation Spreadsheet v9.80 š and the results from the spreadsheet into the Special Features part of the SAP 9.80 software. œ ž Ÿ They must NOT be entered directly into SAP 2005 version 9.80 software 2 X P A U 0 U 2 1 l? P 3 2 R U w Q X Y 3 0 A l A x s X Š 0 X U Y V Š Results for Approved Document F (at maximum flow rate condition) k 0 s 2 A Table Q4 ] : 7 N H ` H N : 9 E ; = ` H [ D b M _ D : E Ž [ = D E 9 7 ] : 7 N H ` Ž [ = D E 9 8 M ; : f H ` Exhaust terminal Fan ; d [ : speed 9 ` N d E Total H N : d [ exhaust : 9 ` N d E ] H Total N : d [ : supply 9 ` N d E ] configuration ] : setting ` H ] : 9 ` D D ` H N flow u rate } : v (l/s) flow u rate } : v (l/s) < b b E H h n n Kitchen + 100% h q Œ n h q Œ n h f ] E ; D ` N E ; E G ] ; 7 = I [ ; ` [ g D E additional wet room Variable < b b E H h n n Kitchen + 100% K h Œ n K h Œ n K f ] E ; D ` N E ; E G ] ; 7 = I [ ; ` [ g D E additional wet rooms Variable < b b E H h n n Kitchen + 100% K J Œ n K J Œ n i f ] E ; D ` N E ; E G ] ; 7 = I [ ; ` [ g D E additional wet rooms Variable < b b E H h n n Kitchen + 100% i i Œ n i i Œ n o f ] E ; D ` N E ; E G ] ; 7 = I [ ; ` [ g D E additional wet rooms Variable < b b E H h n n Kitchen + 100% i p Œ n i p Œ n q f ] E ; D ` N E ; E G ] ; 7 = I [ ; ` [ g D E additional wet rooms Variable? R U Comments B E ; g < ; b 7 H [ H G E H ] E : 9 [ D 8 ; [ 9 [ g E D j K E D D E ; 9 [ g E D j i Œ ` b b E g E N N E Œ = E ] Ž a j Only figures from Table Q2 or Table Q3, not both, should be used with the SAP Q Calculation g E ; E N H ` H N : ; E N H E [ ; b E 9 8 M ; ] E H H E 9 E b H M D M N ` 9 f C E Spreadsheet for this technology type. [ g E D j o ; E : 7 D 9 [ 9 E ; N D ] E ; b 7 H 8 M ; b ; [ G ` 8 M ; g ` H ] E D : E = E ] N M ] b E H ] 9 ] M b 7 = E H 9 ª Table Q4 results are only applicable for Approved Document F requirements. 22

23 Declaration of Conformity I ` E ; b D ; E ; Œ [ 9 7 ] : 9 f ; E 9 g E : b ; E G E 9 d E ; 7 H ] E ; M G E ; d M D ] E ; { ; ] E 9 : b ; [ G ` 8 M ; g ` H ] E D : E = E ] We declare that the equipment detailed below conforms to the requirements of the EC council E D E b 9 ; M = [ N H E 9 ` : b b M = C [ 9 ` g ` D ` 9 E 9 M N : ` b b E ; d E ] [ 8 E D E b 9 ; ` : b 7 ] : 9 f ; directives relating to electromagnetic compatibility and safety of electrical equipment. ] : 9 f ; : 9 f C E I [ ; = E N E H ` H ] G ` H ] ` H N : [ C C [ ; [ 9 = M ] E D / «Equipment type: The Heat Recovery Appliance Model: DV72 6 E G E ; E 9 [ 8 Supplied by Airflow Developments Limited ` ] E D D E c M 7 : E Œ 6 [ H \ [ : 9 E ; L M [ ] Aidelle House, Lancaster Road ^ ; E : : E F _ 7 : ` H E : : a [ ; b Cressex Business Park c ` N d e f \ M = g E High Wycombe _ 7 \ b ` H N d [ = : d ` ; E Buckinghamshire c a h K i j a HP12 3QP D 8 o o u n v h o p o q K q K q K T: +44 (0) Visit: airflow.com _ E : b ; ` G E D : E [ 8 7 ] : 9 f ; E 9 { H d E ] 9 ` D = E b [ H ` : b G E H 9 ` D [ 9 ` M H = E ] G [ ; = E N E H ` H ] G ` H ] ` H N Description of equipment: Mechanical Heat Recovery Ventilation Unit L E D [ 9 ` G E { ] ` ; E b 9 ` G E ; K n n o } h n ~ } { ^ u { ^ v Relative EC Council Directives: 2004/108/EC (EMC) K n n } p q } { ^ u 6 I B v 2006/95/EC (LVD) H G E H ] 9 E d [ ; = M H ` : E ; E ] E { n i i q h K n n K } K K n n Applied : 9 [ H ] [ ; ] Harmonised E ; Standards: EN :2002/A2:2006 { n i i q K ~ n K n n i } h K n n o EN :2003/A1:2004 _ Ž { i n ~ h p p J BS EN 308:1997 { h i h o h J K n n o EN :2004 Airflow Developments Limited warrants that heat recovery appliances are manufactured from high quality ] ` ; E b 9 ` G materials and that continuous quality control ensures that they comply with the above directive. 23

24 Warranty B E 9 9 E C ; M ] 7 b 9 d [ ; E H N [ ; [ H 9 ` C E ; ` M ] E C 9 M ; [ ; [ H 9 ` E H b [ H 7 ] G ` ] E : 9 ` D L { ; = M ] 8 E D g E d 8 9 E ] E This product has a warranty period of two years. The warranty can be upgraded to THREE years from the date of purchase against faulty material or workmanship by registering on our web site [ ; [ H 9 ` E H ] b b E ; b 7 H C ; M ] 7 b 9 E 9 M N ` b b E ` H : 9 [ D D [ 9 ` M H : 7 ] N ` 8 9 E ; H E The warranty only covers the product and not the installation cost. In case such a fault in the manufacture becomes apparent during the Warranty Period, Airflow may, at : b < H Œ N ; [ 9 ` : ; E C [ ; E ; E C ; M ] 7 b 9 E 9 E D D E ; ; E 8 7 H ] E ; E 7 ] N ` 8 9 E H 9 ` D C ; M ] 7 b 9 E 9 Œ Ž 6 ± { ² c I Ž its absolute discretion, repair the product free of charge or refund the cost of the product AS LONG AS AND h a ONLY ; M ] 7 b IF: 9 E 9 ; E 9 7 ; H E ; E : = E ] ] [ 9 E ; E 9 b < g : g E G ` : ` H ] E H 8 M ; N [ ; [ H 9 ` C E ; ` M ] E H 1. K The a ; M ] product 7 b 9 E 9 ` b b is E returned d [ ; G ; E 9within 8 E D [ H the G E H Guarantee ] 9 E D D E ; g E d Period [ H ] D E 9 7 with 8 M ; : evidence ` N 9 ` N 9 E D D E ; of = purchase E ] E H 8 M ; b date E ; 9 : C H ] ` H N : 8 M ; : f H ` H N 2. The product has not been misused or handled carelessly or used on an inappropriate voltage supply 3. Repairs have not been attempted other than by Airflow s service staff or 4. In Airflow s sole discretion, the product is found to be faulty. If it were not found to be faulty, the product would be available for collection from the relevant Airflow premises within one calendar month and if it was not collected, it would be subsequently delivered by Airflow and q { ; g D E G E 9 ` H : 9 [ D D E ; E 9 ` M G E ; E H : : 9 E = = E D : E = E ] ] E : E H E : 9 E g f N H ` H N : ; E N D E = E H 9 E ; M N { { { a delivery charge will be made. g E : 9 E = = E D : E ; H E 8 M ; D E ] H ` H N : 8 < ; ` H N 5. Has been installed in accordance with the latest Building Regulations and IEE Wiring B E H H E N [ ; [ H 9 ` N ` G E ; ` b b E [ H ] ; E ; E 9 9 ` N d E ] E ; E H ] ] E = Œ ] E ; 7 ] 9 ; f b b E D ` N 9 E ; 8 [ : 9 : [ 9 d E ; M G E ; M N ] b b E ; ` b b E b ; [ G 8 M ; E Regulations. 8 9 E ; 8 < D N E H ] E 9 [ g Œ : b [ ] E ; E D D E ; M = b M : 9 H ` H N E ; 8 M ; g 7 H ] E 9 = E ] 7 ] : b ` 8 9 H ` H N [ 8 ] E 9 ] E 8 E b 9 E C ; M ] 7 b 9 This warranty does not confer any rights other than those expressly set out above and does not cover [ ; [ H 9 ` E H 9 ` D g f ] E : : M = E H E b : 9 ; [ 8 M ; ] E D M N C G ` ; b E ; ` b b E 8 M ; g ; 7 N E ; E H : D M G g E : 9 E = 9 E ; E 9 9 ` N d E ] E ; any claims for consequential loss, damage or any costs incurred in the replacement of the faulty product. D D E M C D f : H ` H N E ; G [ ; b M ; ; E b 9 E C 9 ` ] : C 7 H b 9 E 9 8 M ; ; E ] [ b 9 ` M H E H : [ 8 : D 7 9 H ` H N This warranty is offered as an extra benefit and does not affect your statutory right as a consumer. b [ H 8 : G E ] d E H G E H ] E D : E All information believed correct at time of going to press. All goods are sold according to Airflow Developments Limited s Standard Condition of Sale which is 8 available M ; G [ ; : E D on request. In the interest of continuous development Airflow Developments Limited continuously strive to improve their products and reserve the right to change specifications and prices without prior notice. Copyright Airflow Developments Ltd Airflow Developments Limited ³ µ ¹ º» ¼ ½ ¾ À ¾» Á  à ¹ ¾ µ Aidelle House, Lancaster Road Ä Â»» Å Æ º»»» Ç ¾ Â È ¼ É Ê Ë Ì À ¹ Í Î Cressex Business Park, High Wycombe Æ º À È É Ê ¾ Í» Ê Â Ï Ç Ð Ñ Ò Ó Ç Ï Ô Õ Buckinghamshire. HP12 3QP. UK info@airflow.com Ö ¹ Ø Ù Ú Ú Û Ü Ý Ð Ú Þ Ú ß Ñ ß Ñ ß Ñ Telephone: +44(0) à ¾ Å Ø Ù Ú Ú Û Ü Ý Ð Ú Þ Ú Ú á Ð Ü â Ò Facsimile: +44(0)