Siemens Authorized Training Center Supreme Didactic Sdn Bhd 77, Jalan Jintan Manis Taman Supreme, Cheras, 56100, Kuala Lumpur

Transcription

1 Siemens Authorized Training Center Supreme Didactic Sdn Bhd 77, Jalan Jintan Manis Taman Supreme, Cheras, 56100, Kuala Lumpur Tel : Fax : siemens.atc@supreme-didactic.com Website:

2 t r a i n i n g f o r a u t o m a t i o n a n d i n d u s t r i a l s o l u t i o n s 1. SIMATIC S7-300 Basic PLC BASIC with Step7 (ST-BPLC) 3 days COURSE CONTENT Requirements This course is for SIMATIC S7-300 PLC first time users or the beginners who are involved with developing or maintaining automation systems and their application programs. Objectives This course is the first in a three part series which builds the very basic skills with Siemens STEP7 engineering software in project design and application sustaining. This course takes a systems approach addressing the S7300 PLCs, hardware configuration plus basic level of programming. The course format consists of instruction and hands-on exercises. The course uses a conveyor model for demonstrations and exercises. Upon completion of this course, the participant shall be able to: Complete a system hardware configuration. Perform I/O addressing. Use symbolic addressing. Build a STEP7 program. Download & Upload. Program Bit logic instructions. Program Timer instructions. Program Counter instructions. Program Comparison instructions. Program Arithmetic instructions. Perform basic troubleshooting Course Certificate Certificate of participation will be awarded after the training.

3 t r a i n i n g f o r a u t o m a t i o n a n d i n d u s t r i a l s o l u t i o n s SIMATIC S7-300 Basic PLC BASIC with Step7 (ST-BPLC) 3 days COURSE OUTLINE The major topics to be covered are: System Family Training Units Simatic Manager Hardware Configuration Symbols Blocks Binary Operation Digital Operation Basic Troubleshooting Hardware / Software to be used S7 300 CPU based trainer kit Process I/O Simulator Panel Conveyor Model Step7 SIMATIC Manager

4 t r a i n i n g f o r a u t o m a t i o n a n d i n d u s t r i a l s o l u t i o n s SIMATIC S7-300 Basic PLC BASIC with Step7 (ST-BPLC) 3 days COURSE SCHEDULE Day Day 1 SIMATIC S7 System Family overview Training Units & SIMATIC Manager Symbols Hardware Configuration Day 2 Step7 Blocks Binary Operations Day 3 Digital Operations Basic Troubleshooting Feedback & Valedictory session Break Timings: 10:00 Hrs 10:15 Hrs Morning TeaBreak 12:00 Hrs 13:00 Hrs Lunch Break 15:00 Hrs 15:15 Hrs Afternoon Tea Break 17:00 Hrs 17:15 Hrs Recess & End of Day

5 2. SIMATIC S7-300 Maintenance Basic (ST-SERV1) 5 Days COURSE CONTENT Requirements This course is designed for industry "first responders" to operations controlled with Siemens STEP 7 automated control systems. Participants not requiring programming skills, such as maintenance technicians, electricians, supervisors and others, who need an understanding of their Siemens control system to maximize line uptime, should attend this course. This course also makes a great platform for those new to automation systems and industrial electronics. Objectives This course provides Participants with a solid base of STEP 7 PLC tools and skills necessary for successful system diagnostics and repair. This course is ideal for environments with high uptime requirements and stable control system programs. Fully functional application programs are used as a baseline for the participant to understand key process flow information, diagnostics tools and repair techniques. Build skills and reduce downtime with this focused automation system troubleshooting course. Upon completion of this course, the participant shall be able to: Identify and maintain the components of a typical automation system. Understand the basic steps in hardware assembly, cabling, wiring and testing. Establish communications with the PLC with multiple technologies. Retrieve, Archive, and Download programs. Use the hardware configuration editor to inspect and troubleshoot hardware problems. Use SIMATIC Manager tools for basic program administration tasks. Establish connections to an HMI & Drive system. Follow program power/logic flow and interpret/modify basic program elements. Course Certificate Certificate of participation will be awarded after the training.

6 SIMATIC S7-300 Maintenance Basic (ST-SERV1) 5 Days COURSE OUTLINE The major topics to be covered are: The SIMATIC S7 System Family Training Units and Addressing Installation/Maintenance of PLC The SIMATIC Manager Hardware Configuration Symbolic Hardware Commissioning Block Architecture and Block Editor Binary Operations Digital Operations Introduction to PROFIBUS/PROFINET Rewiring a User Program Documenting, Saving, Archiving Closing Exercise Hardware / Software to be used S7 300 CPU based trainer kit Siemens Touch Panel Remote I/O Station Siemens Digital AC Drive Process I/O Simulator Panel Conveyor Model WinCC Flex Software Step7 Simatic Manager

7 t r a i n i n g f o r a u t o m a t i o n a n d i n d u s t r i a l s o l u t i o n s SIMATIC S7-300 Maintenance Basic (ST-SERV1) 5 Days COURSE SCHEDULE Day Day 1 SIMATIC S7 System Family overview Training Units and Addressing Installation/Maintenance of PLC Day 2 SIMATIC Manager Symbols Hardware Configuration Day 3 Hardware Commissioning Block Architecture and Block Editor Binary Operations Day 4 Digital Operations Introduction to Profibus / Profinet Day 5 Rewiring a User Program Documenting, Saving, Archiving Closing Exercise Break Timings: 10:00 Hrs 10:15 Hrs Morning Tea Break 12:00 Hrs 13:00 Hrs Lunch Break 15:00 Hrs 15:15 Hrs Afternoon Tea Break 17:00 Hrs 17:15 Hrs Recess & End of Day

8 3. SIMATIC S7-300 Programming Level 1 (ST-PRO1) 5 days COURSE CONTENTS Requirements This course is for SIMATIC S7-300 PLC users who are involved with developing or sustaining automation systems and their application programs. Objectives This course is the second in a three part series which builds skills with Siemens STEP7 engineering software in project management, program design and application sustaining. This is an aggressively paced curriculum covering key programming tools, structures, libraries and editors. This course takes a systems approach addressing the S7300 PLCs, plus basic connectivity and functionality of an HMI, Drive and PROFIBUS based remote I/O. Throughout this course Participants will build or modify a STEP7 project using proper program structuring, documentation and test tools. Various instructions, memory types, blocks and functions will be introduced to provide the participant with solid concepts of structured programming. The course format consists of instruction and hands-on exercises. The course uses a conveyor model for demonstrations and exercises. Upon completion of this course, the participant shall be able to: Complete a system hardware configuration. Build, document, test and troubleshoot a structured STEP7 program. Program using the multiple address types. Use symbolic addressing. Use core application instructions, functions and blocks. Program using the processed analog values. Generate data blocks. Establish connections to an HMI & Drive system. Course Certificate Certificate of participation will be awarded after the training

9 SIMATIC S7-300 Programming Level 1 (ST-PRO1) 5 days COURSE OUTLINE The major topics to be covered are: SIMATIC S7 System Family Training Units and Addressing SIMATIC Manager Hardware Configuration Symbolic Addressing Block Architecture and Block Editor Binary Operations Digital Operations Introduction to Profibus DP / Profinet Data Blocks Functions and Function Blocks (1) Organization Blocks (1) Troubleshooting + Debugging Functions Hardware / Software to be used S7 300 CPU based trainer kit Siemens Touch Panel Remote I/O Station Siemens Digital AC Drive Process I/O Simulator Panel Conveyor Model WinCC Flex Software Step7 Simatic Manager

10 SIMATIC S7-300 Programming Level 1 (ST-PRO1) 5 days COURSE SCHEDULE Day Day 1 SIMATIC S7 System Family overview Training Units & SIMATIC Manager The Simatic Manager Day 2 Hardware Configuration Symbolic Addressing Block Architecture and Block Editor Day 3 Binary Operations Digital Operations Introduction to Profibus DP / Profinet Day 4 Data Blocks Functions and Functions Blocks (1) Day 5 Organization Blocks (1) Troubleshooting + Debugging Functions Feedback & Valedictory session Break Timings: 10:00 Hrs 10:15 Hrs Morning Tea Break 12:00 Hrs 13:00 Hrs Lunch Break 15:00 Hrs 15:15 Hrs Afternoon Tea Break 17:00 Hrs 17:15 Hrs Recess & End of Day

11