ALUMINUM CONTINUOUS GEARED HINGES STANLEY ARCHITECTURAL HARDWARE

Transcription

1 UMINUM CONTINUOUS GEARED HINGES STANLEY ARCHITECTUR HARDWARE

2 STANLEY ARCHITECTUR HARDWARE TABLE OF CONTENTS Page Table of contents... 2 Company history series continuous hinge design... 3 General information and options Sizing doors and frames... 6 COMPANY HISTORY The Stanley Works New Britain, CT in 843 Page Full mortise... 7 Half surface... 8 Full surface... 9 Full surface swing clear... 0 EDP numbers and extras... As a young man in 843, Frederick T. Stanley founded The Stanley Works a small company located in New Britain, Connecticut that manufactured hinges, bolts and other door hardware in a one-story wooden building. Mr. Stanley s vision was to create a hardware company with unsurpassed customer service, product innovation and integrity and to offer products that would become the first choice among professionals around the world. With the early success of this mission and an increasing demand for his high-quality goods, Mr. Stanley began exporting his products in the 870s. Today, Stanley is a global organization supplying hardware and tools for the architectural, consumer, industrial and residential markets worldwide. Utilizing state-of-the-art research, manufacturing and quality-control capabilities, Stanley continues to deliver the innovative, high quality products that have made the Stanley name synonymous with the highest craftsmanship and dependability for more than 60 years. To our valued customers, we appreciate your loyalty over the years and proudly present our Architectural Hardware offering. Commercial Customer Service: UMINUM 3 KNUCK CONTINU

3 660 Series Continuous Hinges Installs in minutes Lasts a lifetime Stanley 660 Series Continuous Hinge design is as tough and practical as it is attractive. Made of 6065 T5 aluminum, it is designed and built to last for the life of the building. Uniquely shaped form follows function bearing channel is pleasing to the eye and applauded by architects. The standard duty hinge has 6 bearings for a typical 7' door compared to 32 bearings on a heavy duty design for the same door height. Lubricated with polytetrafluoroethylene for maximum durability. Utilizing computer aided finite element analysis, is precision engineered with a minimum number of fasteners, thus reducing installation time without sacrificing performance. Innovative anti spinning through-bolts on half surface and full surface models reduce labor cost. All models conform to ANSI/BHMA A , Grade Standard. Product right out of the box has a 90 minute fire rating. Hinges for 3 hour fire doors use heat activated fire pins (FP). All have been tested and certified by UL to UL0C Standard. Available in anodized clear (), BHMA 628 and dark bronze (), BHMA 70 finishes. STANLEY ARCHITECTUR HARDWARE Limited Lifetime Warranty Stanley warrants this product to the original purchaser for its useful life (not to exceed one year for products with electrical or electronic components) against deficiencies in material and workmanship. This LIMITED LIFETIME WARRANTY does not cover products that are improperly used, abused, altered or repaired. Deficient products will be replaced or repaired. In addition, any Architectural Hardware items trademarked with Lifespan are covered by a LIMITED LIFETIME WARRANTY for the life of the building in which the products were originally installed. Please call your Stanley Sales Representative or Customer Service for more information and/or return instructions. THIS LIMITED LIFETIME WARRANTY IS GIVEN IN LIEU OF L OTHERS INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND EXCLUDES L INCIDENT OR CONSEQUENTI DAMAGES. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so these limitations may not apply to you. This LIMITED LIFETIME WARRANTY gives you specific legal rights that may vary from state to state. OUS GEARED HINGES 3

4 STANLEY ARCHITECTUR HARDWARE General Information and Options How to Determine Hand of Hinge The hand of a hinge is determined from the outside of the door to which it is applied The outside of a cupboard, bookcase or closet door is the room side. For other doors, the outside is usually the side from which security is necessary. the side from which security is necessary Left Hand Left hand door takes left hand hinges Left Hand Reverse Left hand reverse door takes right hand hinges Right Hand Right hand door takes right hand hinges It will be observed that CE this (Concealed method of determining Electric) the hand of loose joint cabinet hinges is exactly the opposite from the furniture manufacturers standard rule Conducts current regardless of door position to electric locks, exit devices, hold To determine the hand open of a devices, loose joint etc. hinge: Specify open hand the hinge available with its option face toward with models: you. If the 660, knuckle 66HD, of 662, the right leaf is at the bottom, it is a right hand hinge. If the knuckle of the left leaf is at the bottom, it is a left and 662HD hand hinge Electrical Ratings Suffix # Wires Volts (AC or DC) 6, 2, 24 Current AMP/Wire AMP/Wire Right Hand Reverse Right hand reverse door takes left hand hinges CS (Concealed Switch) Allows for opening monitoring. Used to actuate alarms, or other security equipment. Specify hand. Available on models: 66, 66HD, 662, and 662HD EPT (Electric Power Transfer) Hinge-leafs are modified to accept an EPT devise. Specify hand, location, manufacturer and model of EPT. 9/6" dia. grommet clip FP (Fire Pin) Hinges for 3 holler fine doors use thermally activated stainless steel, automatic fire pin. DOOR FRAME automatic cross pin protective plug pin stainless steel pin fusible retainer UG599, EDP# are also available for purchase separately 4 UMINUM CONTINU spring

5 HT (Hospital Tip) Barrel end on hinge top is sloped making cleaning easier and making it difficult to attach ropes, clothing apparel, and other items, thus reducing the risk of harm. Specify hand. Dutch Door Prep. Frame leaf is continous and door leaf is two piece. Specify cut portion from bottom of hinge, space between leafs, and hand. Aluminum Replacement Covers For half and full surface hinges 0' Section Section Options 3/6" gap STANLEY ARCHITECTUR HARDWARE School Option Anti vandal plug prohibits insertion of distructive objects into the gears of the hinge. Fasteners Screw Packs 50 ea. TEK Screw Finish ea. TEX Screw Finish The following screw pack sets will cover up to a 0' hinge Set Through-Bolt Full Surface Set Through-Bolt Full Surface Set Through-Bolt Half Surface Set Through-Bolt Half Surface OUS GEARED HINGES 5

6 STANLEY ARCHITECTUR HARDWARE SIZING DOORS AND FRAMES FOR STANDARD AND HEAVY DUTY UMINUM GEARED TYPE CONTINUOUS HINGES* Sizing of doors width for models: 66, 66HD, 662, 662HD Square Edge Door Hinge allowance 5/6" (8mm) Allowance for frame irregularities /32" (0.8mm) Typical lockside clearance /8" (3.2mm) Total 5/32" (2.0mm) Square Edge Door Allowance for 2 hinges 5/8" (5.9mm) Allowance for frame irregularities (2 frames) /6" (.6mm) Typical clearance between doors 3/6" (4.8mm) Total 7/8" (22.3mm) Single Doors Pairs of Doors /8" in 2" Beveled Edge Door Hinge allowance 5/6" (8mm) Allowance for beveled edge door /32" (0.8mm) Allowance for frame irregularities /32" (0.8mm) Typical lockside clearance /8" (3.2mm) Total /2" (2.8mm) /8" in 2" Beveled Edge Door Allowance for 2 hinges 5/8" (5.9mm) Allowance for beveled edge door (x2) /6" (.6mm) Allowance for frame irregularities (2 frames) /6" (.6mm) Typical clearance between doors 3/6" (4.8mm) Total 5/6" (23.9mm) Sizing of doors width for models: 663, 663HD Single Door (square or beveled edge) Hinge allowance /8" (3.2mm) Allowance for frame irregularities /32" (0.8mm) Typical lockside clearance /8" (3.2mm) Total 9/32" (7.2mm) Pairs of Door (square or beveled edge) Allowance for 2 hinges /4" (6.4mm) Allowance for frame irregularities (2 frames) /6" (.6mm) Typical clearance between doors 3/6" (4.8mm) Total /2" (2.8mm) Sizing of doors width for models: 664, 664HD, 665, 665HD Allowance for frame irregularities /32" (0.8mm) min. Typical lockside clearance /8" (3.2mm) Total 5/32" (4.8mm) min. Allowance for frame irregularities (2 frames) /6" (.6mm) min. Typical clearance between doors 3/6" (4.8mm) Total /4" (6.4mm) min. * Please be advised that the suggested clearance outlined here are for typical applications. Individual applications may differ. Please also note that: Beveled edge doors are measured on the high side. Recommended head clearance for all models is /8". 6 UMINUM CONTINU

7 STANLEY ARCHITECTUR HARDWARE UMINUM CONTINUOUS GEARED HINGES Full Mortise UMINUM CONTINUOUS GEARED HINGES Full Mortise 66 Full Mortise Standard Duty for flush door and frame applications 66 Standard Duty for flush door and frame applications 66 HD Heavy Duty for flush door and frame 66 applications HD Heavy Duty for flush door and frame applications 662 Standard Duty for 3 /32" inset doors 662 Standard Duty for 3 /32" inset doors HD HD Heavy Duty for 3 /32" " inset doors 662 HD Heavy Duty for 3 /32" inset doors Distributes door weight and and stress along the the full full length of of door and and frame No No misaligned pivot points of of individual hinges Typically no no additional reinforcement required Clear aluminum and and dark bronze anodized finishes Standard duty and and heavy duty conform to to ANSI/BHMA Standard A , Grade Supports doors up up to to lbs lbs LifeSpan hinge covered by by a a limited lifetime warranty for for the the life life of of the the building Engineered with with polymer PTFE bearing for for maximum durability 90-minute rating standard on on all all hinges. 3-hour rating available with with fire fire pins pins (FP) Hinges can can be be furnished as as follows: with tips Hinges can with be hospital furnished tips as (HT) follows: with with with hospital electric wires tips (HT) (CE) with with electric wires switches (CE)(CS) with with electric switches power transfer (CS) (EPT) prep Specify manufacturer and and model number of of transfer with with electric dutch door power prep transfer (EPT) prep Specify manufacturer and model number of transfer custom with dutch length door prep school custom option length school option STANLEY ARCHITECTUR HARDWARE /32 /32 (9 (9 mm) mm) Beveled Door Beveled Door 5/6 5/6 (8 mm) (8 mm) Square Door Square Door 66/66HD Full Full Mortise Mortise Flush Flush Door Door & & Frame Frame /32 /32 (9 mm) (9 mm) Beveled Door Beveled Door 5/6 5/6 (8 mm) (8 mm) Square Door Square Door 662/662HD 662/662HD Full Mortise Full Mortise 3/32" 3/32" Inset Inset Length Length Finish Inches (mm) Finish Inches 79 (mm) (2006) & (2006) (208) && (208) (243) && 9 95 (243) (3022) && 9 (3022) & Wood and Machine screws available separately Wood and Machine screws available separately Number of #2-24 x 5/8" TEK Number Screws of Per #2-24 Hingex 5/8" TEK Screws Per Hinge Quantity Carton Weight Per Carton Quantity Carton Weight Per CartonLbs. (KG) Lbs. (KG) 7 (5.4) 7 7 (5.4) (5.4) 8 7 (7.6) (5.4) 0 8 (22) (7.6) 0 (22) OUS GEARED HINGES 4 UMINUM CONTINU7

8 STANLEY ARCHITECTUR HARDWARE Half Surface 663 Standard Duty 663 HD Heavy Duty Distributes door weight and stress along the full length of door and frame Ideal for retrofit applications No misaligned pivot points of individual hinges Clear aluminum and dark bronze anodized finishes Standard duty and heavy duty conform to ANSI/BHMA Standard A , Grade Supports doors up to 600 lbs LifeSpan hinge covered by a limited lifetime warranty for the life of the building Engineered with polymer PTFE bearing for maximum durability Anti-spinning through-bolts reduce installation labor costs Universal cover plates for all configurations 90-minute rating standard on all hinges. 3-hour rating available with fire pins (FP) Hinges can be furnished as follows: with hospital tips (HT) with dutch door prep custom length school option Replacement covers available separately 663 Length Inches (mm) 79 (2006) 83 (208) 95 (243) 9 (3022) Finish & & & & Number of #2-24 x 5 /8" TEK Screws Per Hinge Number of #2-24 x /2" Through-Bolts and #2-24 x /8" Machine Screws Per Hinge Qty Per Carton Carton Weight Lbs. (KG) 7 (5.4) 7 (5.4) 8 (7.6) 0 (22) Wood and Machine screws available separately 8 US GEARED UMINUM HINGESCONTINU

9 Distributes door weight and stress along the full length of door and frame Ideal for retrofit applications No misaligned pivot points of individual hinges Clear aluminum and dark bronze anodized finishes Standard duty and heavy duty conform to ANSI/BHMA Standard A , Grade Supports doors up to 600 lbs LifeSpan hinge covered by a limited lifetime warranty for the life of the building Engineered with polymer PTFE bearing for maximum durability Anti-spinning through-bolts reduce installation labor costs Universal cover plates for all configurations 90-minute rating standard on all hinges. 3-hour rating available with fire pins (FP) Hinges can be furnished as follows: with hospital tips (HT) with dutch door prep custom length school option Replacement covers available separately Full Surface 664 Standard Duty for standard and narrow jamb applications 664 HD Heavy Duty for standard and narrow jamb applications STANLEY ARCHITECTUR HARDWARE Standard Jamb Narrow Jamb 664 Inches Length (mm) Finish Number of #2-24 x 5 /8" TEK Screws Per Hinge Number of #2-24 x /2" Through-Bolts and #2-24 x /8" Machine Screws Per Hinge Qty Per Carton Carton Weight Lbs. (KG) 79 (2006) 83 (208) 95 (243) 9 (3022) & & & & (5.4) 7 (5.4) 8 (7.6) 0 (22) Wood and Machine screws available separately OUS GEARED HINGES UMINUM CONTIN 9

10 STANLEY ARCHITECTUR HARDWARE Full Surface Swing Clear 665 Standard Duty 665 HD Heavy Duty Swings door out of opening at approximately 90 degrees Distributes door weight and stress along the full length of door and frame No misaligned pivot points of individual hinges Clear aluminum and dark bronze anodized finishes Standard duty and heavy duty conform to ANSI/BHMA Standard A , Grade Supports doors up to 600 lbs LifeSpan hinge covered by a limited lifetime warranty for the life of the building Engineered with polymer PTFE bearing for maximum durability Anti-spinning through-bolts reduce installation labor costs Universal cover plates for all configuration 90-minute rating standard on all hinges. 3-hour rating available with fire pins (FP) Hinges can be furnished as follows: with hospital tips (HT) with dutch door prep custom length school option Replacement covers available separately 665 Inches Length (mm) Finish Number of #2-24 x 5 /8" TEK Screws Per Hinge Number of #2-24 x /2" Through-Bolts and #2-24 x /8" Machine Screws Per Hinge Qty Per Carton Carton Weight Lbs. (KG) 79 (2006) 83 (208) 95 (243) 9 (3022) & & & & (5.4) 7 (5.4) 8 (7.6) 0 (22) Wood and Machine screws available separately 0 US GEARED UMINUM HINGESCONTINU

11 EDP Numbers and Extras CLASS NO HD CLASS NO HD LENGTH FINISH EDP NO LENGTH FINISH EDP NO CLASS LENGTH FINISH EDP NO. NO HD CLASS LENGTH FINISH EDP NO. NO HD CLASS LENGTH FINISH EDP NO. NO HD ELECTRIC OPTIONS STANLEY ARCHITECTUR HARDWARE For more information on Stanley Security Solutions products, services, and office locations visit our web site at Product information contained in this catalog has been com piled and presented with as much care and com plete ness as is reasonably possible. Errors or mistakes may be present, and in many cases, reliance has been placed on information supplied by other manufacturers which may be in error or which may be subject to changes or mod ifications by the man ufactur er with out no tice and without obligation. Therefore, no guar an tee can be made or should be assumed or implied with regards to product in formation con tained in this catalog. OUS GEARED HINGES

12 STANLEY ARCHITECTUR HARDWARE Stanley Security Solutions, Inc. 66 E. 75th Street Indianapolis, Indiana Stanley Security Solutions, Inc. and Stanley Logistics 0M R082 SAH02