DOORS HOLLOW METAL MANUAL NAAMM STANDARD NAAMM HMMA METAL DOORS & FRAMES METAL. A Division of
|
|
- Anissa Payne
- 7 years ago
- Views:
Transcription
1 HOLLOW METAL MANUAL NAAMM STANDARD HMMA d NAAMM HMMA METAL DOORS & FRAMES HOLLOW METAL DOORS 8d NAAMM HMMA METAL DOORS & FRAMES A Division of HOLLOW METAL MANUFACTURERS A S S O C I A T I O N NATIONAL ASSOCIATION OF ARCHITECTURAL METAL MANUFACTURERS
2 This Manual was developed by representative members of and approved by the Hollow Metal Manufacturers Association (HMMA) Division of the National Association of Architectural Metal Manufacturers (NAAMM) to provide their opinion and guidance on the basic design of hollow metal doors and frames. This standard contains advisory information only and is published as a public service by NAAMM and its HMMA Division. NAAMM and its HMMA Division disclaim all liability of any kind for the use, application, or adaptation of material published in this standard. Purchasers of NAAMM Standards may receive current information on all NAAMM Standards by calling or writing the National Association of Architectural Metal Manufacturers. National Association of Architectural Metal Manufacturers 800 Roosevelt Road Bldg. C, Suite 312 Glen Ellyn, Illinois Phone: (630) Fax: (630) Copyright 1977, 1987, 2009 National Association of Architectural Metal Manufacturers All Rights Reserved
3 TABLE OF CONTENTS Part 1 INTRODUCTION A. General...3 B. Types of Construction...3 C. Clearance Dimensions and Hardware Locations...4 D. Door Hand Designations...4 E. Door Designs...5 Part 2 - CONSTRUCTION FEATURES A. Constructions...5 B. Meeting Edge Profiles...6 C. Stiffener Sections...6 D. Stile Edge Details...6 E. Top Edge Details...6 F. Bottom Edge Details...6 G. Top Edge Details with Flush Transom Panel...6 H. Glazed Opening and Recessed Panel Moldings...7 I. Muntins...7 J. Louver Designs...7 K. Hardware Preparations...8 NAAMM HMMA HOLLOW METAL DOORS 1
4 2 HOLLOW METAL DOORS NAAMM HMMA
5 HOLLOW METAL DOORS PART 1 - INTRODUCTION A. General Doors may be classified by their method of operation. There are four basic types: swinging, sliding, rolling steel, and revolving. Though revolving doors are seldom, if ever, made of carbon steel, sliding and rolling steel may be hollow metal. This standard applies to hollow metal doors that are side-hinged swinging and mounted on either hinges or pivots B. Types of Construction The details shown on the following pages pertain to HMMA door constructions outlined in the following NAAMM/HMMA standard specifications: HMMA 860, Guide Specifications for Hollow Metal Doors and Frames, is used and specified for hollow metal doors and frames subject to less rigorous use than commercial and institutional applications. ANSI/HMMA 861, Guide Specifications for Commercial Hollow Metal Doors and Frames, is used and specified in commercial work is the continuously welded edge seam construction and it is this type that is the basis of the NAAMM Standard. ANSI/HMMA 862, Guide Specifications for Security Hollow Metal Doors and Frames, is used and specified in applications where security against vandalism, break-in, or theft is a major concern. ANSI/HMMA 863, Guide Specifications for Detention Security Hollow Metal Doors and Frames, is used and specified for detention security. ANSI/HMMA 865, Guide Specifications for Swinging Sound Control Hollow Metal Doors and Frames, is used and specified for applications where sound control is a factor. ANSI/HMMA 866, Guide Specifications for Stainless Steel Hollow Metal Doors and Frames, is used and specified when stainless steel is required for corrosion resistance or aesthetics is a factor. ANSI/HMMA 867, Guide Specifications for Commercial Laminated Core Hollow Metal Doors and Frames, is used and specified for doors incorporating the use of laminated cores. HMMA 850, Fire rated Hollow Metal Doors and Frames. Since fire rated doors may differ in certain details of construction, refer to HMMA 850, Fire Rated Hollow Metal Doors and Frames standard for guidance. NAAMM HMMA HOLLOW METAL DOORS 3
6 C. CLEARANCE DIMENSIONS & HINGE LOCATIONS 1/8" NOMINAL DOOR WIDTH (FRAME OPENING) ACTUAL DOOR WIDTH 1/8" 10" EQUAL EQUAL 5" HINGE CUTOUTS VARIES AS SPECIFIED (3/4"MAXIMUM FOR LABELED DOORS) ACTUAL DOOR HEIGHT NOMINAL DOOR HEIGHT(FRAME OPENING) Floor D. DOOR HAND DESIGNATIONS SINGLE PAIR DOUBLE EGRESS COMMUNICATING RIGHT HAND (RH) RIGHT HAND ACTIVE (RHA) (LHR) LHR/LH LEFT HAND (LH) LEFT HAND ACTIVE (LHA) (RHR) RHR/RH RIGHT HAND REVERSE (RHR) RIGHT HAND REVERSE ACTIVE (RHRA) CONTRA-SWING LEFT HAND REVERSE (LHR) LEFT HAND REVERSE ACTIVE (LHRA) RH/LHR RHR/LH DOUBLE ACTING (DA) DOUBLE ACTING (DA) LH/RHR LHR/RH = KEY SIDE 4 HOLLOW METAL DOORS NAAMM HMMA
7 E. DOOR DESIGNS FLUSH VISION LIGHT NARROW LIGHT TWO NARROW LIGHTS HALF LIGHT TWO HALF LIGHTS FULL LIGHT ROUND LIGHT OVAL LIGHT BOTTOM LOUVER FULL LOUVER NARROW LIGHT w/louver HALF LIGHT w/louver HALF LIGHT w/muntin EMBOSSED OR APPLIED MOLDING DUTCH DOOR w/shelf PART 2 CONSTRUCTION FEATURES A. Constructions There are two basic types of door constructions: STEEL STIFFENERS Vertical steel stiffeners, which can be channel, zee, hat, or similar shaped sections, support the face sheets. The stiffeners are attached to the face sheets by spot or projection welding. LAMINATED CORE This is a sandwich construction in which the face sheets are separated by a core comprised of honeycomb ( Kraft paper) or polyurethane or polyisocyanurate or polystyrene or core board or steel stiffeners. The core is laminated to the faces by means of an adhesive. Foamed-in-place polyurethane cores are self-bonding and do not require additional adhesive. Closer Reinforcement Stiffener Insulation Face sheet NAAMM HMMA HOLLOW METAL DOORS 5
8 V-BEVEL BULLNOSE USED ON DOUBLE-ACTING CENTER-PIVOTED DOORS CHANNEL ZEE RABBETED PARALLEL BEVEL HAT SECTIONS OFFSET CHANNEL INTEGRAL ASTRAGAL PARALLEL BEVEL WITH MOLDED SURFACE ASTRAGAL TRUSS INTERLOCKING CHANNELS V-BEVEL WITH FLAT SURFACE ASTRAGAL RECESSED WEATHERSTRIPPING B. MEETING EDGE PROFILES C. STIFFENER SECTIONS 2" 1" 8 Channel or angle may be used in place of plate LOCKSEAM PAN & SKIN CENTER SEAM CENTER SEAM INVERTED CHANNEL FLUSH CLOSING CHANNEL SEALED IF REQUIRED. FLUSH CHANNEL SEALED IF REQUIRED D. STILE EDGE DETAILS E. TOP EDGE DETAILS Flush channel optional INVERTED CHANNEL FLUSH CLOSING CHANNEL FLUSH CHANNEL MORTISED DOOR BOTTOM RABBETED INTEGRAL ASTRAGAL APPLIED ASTRAGAL F. BOTTOM EDGE DETAILS G. TOP EDGE DETAILS WITH FLUSH TRANSOM PANEL 6 HOLLOW METAL DOORS NAAMM HMMA
9 H. GLAZED OPENINGS AND RECESSED PANEL MOULDINGS A FLUSH B SECURITY A OVERLAP B I. TYPICAL MUNTINS FLUSH RECESSED BAR STOCK APPLIED J. LOUVER DESIGNS closed position open position knob operator BUILT-IN INVERTED "Y" BLADE LOUVER BUILT-IN "ZEE" BLADE LOUVER APPLIED FUSIBLE LINK ADJUSTABLE LOUVER APPLIED INVERTED "V" BLADE LOUVER NAAMM HMMA HOLLOW METAL DOORS 7
10 K. TYPICAL HARDWARE PREPARATIONS ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) BUTT HINGE INTERMEDIATE MORTISE LOCK CYLINDRICAL LOCK PIVOT ) ) ) ) FLUSH BOLT PANIC HARDWARE 8 HOLLOW METAL DOORS NAAMM HMMA
11 ) ) ) ) ) ) TOP PIVOT BOTTOM PIVOT CONCEALED CLOSER ) ) ) ) ) ) ) ) ) ) ) SURFACE MOUNTED CLOSER NAAMM HMMA HOLLOW METAL DOORS 9
12 RECOMMENDED GUIDE SPECIFICATIONS FOR HMMA HOLLOW METAL DOORS AND FRAMES HMMA 860 Hollow Metal Door and Frames ANSI/NAAMM HMMA 861 Commercial Hollow Metal Doors and Frames ANSI/NAAMM HMMA 862 Commercial Security Hollow Metal Doors and Frames ANSI/NAAMM HMMA 863 Detention Security Hollow Metal Doors and Frames ANSI/NAAMM HMMA 865 Swinging Sound Control Hollow Metal Doors and Frames ANSI/NAAMM HMMA 866 Stainless Steel Hollow Metal Doors and Frames ANSI/NAAMM HMMA 867 Commercial Laminated Core Hollow Metal Doors and Frames RELATED HMMA DOCUMENTS HMMA 800 Introduction to Hollow Metal HMMA 801 Glossary of Terms for Hollow Metal Doors and Frames HMMA 802 Manufacturing of Hollow Metal Doors and Frames HMMA 803 Steel Tables HMMA 810 Hollow Metal Doors HMMA 820 Hollow Metal Frames HMMA 830 Hardware Selection for Hollow Metal Doors and Frames HMMA 831 Recommended Hardware Locations for Hollow Metal Doors and Frames HMMA 840 Installation and Storage of Hollow Metal Doors and Frames HMMA 841 Tolerances and Clearances for Commercial Hollow Metal Doors and Frames HMMA 850 Fire-Rated Hollow Metal Doors and Frames HMMA 890 Technical Summary HMMA 810-TN01 Defining Undercuts HMMA 820-TN01 Grouting Hollow Metal Frames HMMA 820-TN02 Continuously Welded Frames HMMA 820-TN03 Guidelines for Glazing Hollow Metal Transoms, Sidelights and Windows HMMA 840-TN01 Painting Hollow Metal Products
HARDWARE LOCATIONS FOR HOLLOW METAL DOORS AND FRAMES
HOLLOW METAL MANUAL NAAMM STANDARD HMMA 831-11 8d NAAMM HMMA 831-11 METAL DOORS & FRAMES HARDWARE LOCATIONS FOR HOLLOW METAL DOORS AND FRAMES 8d NAAMM HMMA 831-11 METAL DOORS & FRAMES A Division of HOLLOW
More informationHMMA 810 HOLLOW METAL DOORS HOLLOW METAL MANUAL -87 NAAMM STANDARD FOURTH EDITION METAL DOORS & FRAMES NAAMM 2 NAAMM 2 METAL DOORS & FRAMES
HOLLOW METAL MANUAL NAAMM STANDARD HMMA 810-87 8d METAL DOORS & FRAMES NAAMM 2 87 HOLLOW METAL HOLLOW METAL DOORS FOURTH EDITION NAAMM 2 87 8d METAL DOORS & FRAMES A Division of NATIONAL ASSOCIATION OF
More informationHMMA 830 HARDWARE SELECTION FOR HOLLOW METAL DOORS AND FRAMES HOLLOW METAL MANUAL -02 NAAMM STANDARD METAL DOORS & FRAMES NAAMM 01 NAAMM 01
HOLLOW METAL MANUAL NAAMM STANDARD HMMA 830-02 METAL S & FRAMES 8d NAAMM 01 02 HARDWARE SELECTION FOR HOLLOW METAL S AND FRAMES NAAMM 01 02 8d METAL S & FRAMES A Division of HOLLOW METAL MANUFACTURERS
More informationBASIC FIRE DOOR REQUIREMENTS TECHNICAL DATA SHEET NO. 401
BASIC FIRE DOOR REQUIREMENTS SHEET NO. 401 Fire door openings are classified by their locations in the building. The location determines the length of exposure protection required, based on the potential
More informationDoors and frames. Technical data manual 2015 rev. 8/17/15
Doors and frames Technical data manual 2015 rev. 8/17/15 Technical data manual Main table of contents NAVIGATE VIA: A) Rollover links in each TOC (each item below is a link), B) Bookmarks on the left,
More informationSubject: DKS Steel Door and Frames Systems, Inc., ITS / Warnock Hersey Procedural Specification, Certification, and Inspection.
DKS Customers Interested Parties State and Local Authorities Subject: DKS Steel Door and Frames Systems, Inc., ITS / Warnock Hersey Procedural Specification, Certification, and Inspection. All DKS products
More informationTechnical Data Honeycomb Door Leaf 8-1-99
8--99 8-/8 8-7/8 B 8-/4 A A Dim. A Leaf Width B ELEVATION F DESIGN Vertical edge seams mechanically interlocked Square hinge and lock edges 4-/ x.4 full mortise hinge prep Gov. 60/6 cyl lock prep...prefix
More informationSteel Door Institute. Fire Rated Doors and Frames
Steel Door Institute Fire Rated Doors and Frames 1 1. Nomenclature and Overview 2. Fire Rated Frames 3. SDI 118 4. Fire Rated Doors 5. Fire Rated Hardware 6. Specialty Products Table of Contents 2 Fire
More informationDIVISION 8, METAL SOUND CONTROL DOOR ASSEMBLIES PART 1 GENERAL 1.1 RELATED DOCUMENTS
DIVISION 8, METAL SOUND CONTROL DOOR ASSEMBLIES PART 1 GENERAL 1.1 RELATED DOCUMENTS Drawings and general provisions of the contract, including general and supplementary conditions and other Division 1
More informationEXPANSION BOLT ANCHOR:
Stiles Steel Door + Window Systems Glossary of Terms Definitions of terms commonly used in connection with Hollow Metal work, defined as they apply specifically to hollow metal, may be defined differently
More informationn Three 4 x 4 butt hinges per door - prevents wracking and assures smooth positive operation n Heavy duty 16 gauge steel frame
Weather Fin and bulb help keep bad weather outside and good air inside Windows: n Many light kits are available 1-LU 4 X 48 1-LE 16 X 16 1-LA 20 X 24 1-LI 20 X 24 1-B 22 X 36 1-LW 16 X 16 W/GRID 9-LB 22
More informationBasic Fire Door Requirements
TECHNICAL DATA SERIES S D I 118-01 Basic Fire Door Requirements 2001 Steel Door Institute STEEL DOOR INSTITUTE 30200 DETROIT ROAD - CLEVELAND, OHIO 44145 Technical Data Series SDI 118-2001 Basic Fire Door
More information2.02. Specifications. General. Products. Execution. Offset Pivots P-694 Top and Bottom Pivots
2.02 Standard Specifications General Entrances Description Furnish all necessary materials, labor and equipment for the complete installation of aluminum entrance doors, door frames and hardware as shown
More informationquality door and window systems for metal buildings
quality door and window systems for metal buildings knock-down door systems Features and Benefits: Galvanized Doors and Frames Insulated Door Cores Textured Steel Door Faces Completely Reversible (non-handed
More informationNomenclature for: Standard Steel Doors and Frames
ANSI/SDI A250.7-1997 (R2002) Revision and Redesignation of ANSI/SDI A123.1-1989 Nomenclature for: Standard Steel Doors and Frames ANSI/SDI A250.7-1997 STEEL DOOR INSTITUTE SPONSOR Steel Door Institute
More informationWood Sound Retardant Door Hardware Information Bulletin
overly overly 574 West Otterman Street Greensburg, PA 15601 Toll Free: (800) 979-7300 Local: (724) 834-7300 Fax: (724) 830-2871 Email: overly@overly.com DOOR COMPANY Wood Sound Retardant Door Hardware
More informationSECTION 6. Glass Storefront Doors:
SECTION 6 Glass Storefront Doors: Table of Contents 3070 Storefront Door System Description & Dimensions 6070 Storefront Door System Description & Dimensions Door Leaf Detail Optional 10 Bottom Rail Detail
More informationTurning nature s beauty into works of art
f l u s h d o o r s Eggers 5-ply flush doors are the very embodiment of form marrying function - extraordinary beauty and exceptional durability. We are able to produce a variety of custom architectural
More informationDOOR COMPONENTS, INC Technical Data
DOOR COMPONENTS, INC Technical Data DOOR COMPONENTS, INC 7980 Redwood Ave Fontana, CA 92336 Phone (909) 770 5700 Toll Free (866) 989 3667 Fax (909) 770 5722 www.doorcomponents.com INDEX FRAMES: PAGE #
More informationFRAME PROFILE MASONRY METAL DOOR FRAME FLUSH MASONRY KD MITER CORNER JOINT. #8 Screw (MS002485) Required on all fire rated KD frames. Bend Tabs.
FRAME PROFILE MASONRY FLUSH MASONRY KD MITER CORNER JOINT Bend Tabs Head #8 Screw (MS002485) Required on all fire rated KD frames Corner Assembly 2" (50.8) Head Jamb Head Break Away Corner Clip Spot Welds
More informationWHI 90-Minute Rated Veneered Door Frame Installation Instructions
No. 940-03-10 INSTALLATION INSTRUCTIONS 90 MINUTE RATED VENEERED DOOR FRAME DOOR REQUIREMENTS: Consult the door manufacturer to make sure that the doors are qualified for the hardware to be installed,
More informationStainless Steel Continuous Hinges
Stainless Steel Continuous Hinges Hager heavy duty continuous hinges offer proven reliability that can stand up to the daily rigors of high-traffic, high-impact areas. They re designed and engineered to
More informationA Complete Solution CREATING WALLS THAT DEFINE SPACE
A Complete Solution CREATING WALLS THAT DEFINE SPACE COMPANY HISTORY CLIPPER WALL Clipper partitions are part of the Saint- Gobain Group, one of the worldwide leaders in the construction products industry.
More informationGlossary. 1/3 1/3 1/3 - Configuration of a vent-fixed-vent (xox) window in which the vents and fixed panel are equal sizes
Glossary 1/3 1/3 1/3 - Configuration of a vent-fixed-vent (xox) window in which the vents and fixed panel are equal sizes 1/4 1/2 1/4 - Configuration of a vent-fixed-vent (xox) window in which the vents
More informationDE Frame with C Series Sidelight
TOOLS REQUIRED Tape measure 6' magnetic level 3' magnetic level Screw gun with clutch adjusted #2 phillips tip #3 phillips tip Screwdriver (used to adjust frame on will using oval slots) Pry Bar Powder
More informationFabrication Illustration Part No. Description Door Frame. P092 Mortised Butt Hinge P092D P092F (includes P2092 $ 48 $ 21 frame/door reinforcing)
Custom Blank Entrances - Applied Hardware & Preps - Tubelite Standard Hardware Butt Hinges Pivots C2 Page 1 P092 Mortised Butt Hinge P092D P092F (includes P2092 $ 48 $ 21 frame/door reinforcing) P795S
More informationCLEAR-DIVISIONS VARIOFOLD
CLEAR-DIVISIONS VARIOFOLD Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS VARIOFOLD moveable The yellow highlighted areas in the
More informationK. D. FRAME ASSEMBLY FOR CLOSED STEEL STUD WALLS...Ins 10. FRAME INSTALLATION DETAILS FOR CLOSED STEEL STUD WALLS...Ins 11
K. D. FRAME ASSEMBLY FOR MASONRY WALLS...........................Ins 2 FRAME INSTALLATION DETAILS FOR MASONRY WALLS......................Ins 3 INSTALLING EXISTING MASONRY WALL ANCHORS IN FRAME..................Ins
More informationCONCEALED BEARING HINGES. StANLEy ARCHItECtuRAL HARDwARE
CONCEALED BEARING HINGES StANLEy ARCHItECtuRAL HARDwARE STANLEY ARCHITECTURAL HARDWARE TABLE OF CONTENTS Page Table of contents...2 Company history...2 5 knuckle concealed bearing design...3 Full mortise
More informationCLEAR-DIVISIONS CENTERFOLD
CLEAR-DIVISIONS CENTERFOLD Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS CENTERFOLD moveable The yellow highlighted areas in
More informationStandard Steel Doors, Frames, Accessories and Related Components
TECHNICAL DATA SERIES S D I 111-09 Recommended Details for Standard Steel Doors, Frames, Accessories and Related Components The information that follows represents the Standard Steel Door and Frame Industry's
More informationAuxiliary hardware & general information. Exit devices
Auxiliary hardware & general information Exit devices Introduction Since pioneering the first exit device in 1908, Von Duprin life safety products have provided unparalleled quality, performance and flexibility
More informationEggers meticulously-crafted door frames are rivaled only by their beauty, quality and lasting performance. Turning nature s beauty into works of art
D O O R F R A M E S Eggers meticulously-crafted door frames are rivaled only by their beauty, quality and lasting performance. Turning nature s beauty into works of art D O O R F R A M E S Eggers Industries
More informationStandard Door Specification
Element General Requirement To be defined in the project brief but should meet Building Regulations. All doors to be a minimum of 30 minute fire rated and must comply with all relevant UK legislation and
More informationAutomatic Door Selection Guide
Automatic Door Selection Guide AAADM 1300 Sumner Avenue Cleveland, OH 44115 P: 216-241-7333 F: 216-241-0105 aaadm@aaadm.com Automatic Door Selection Guide General: The members of AAADM manufacture an assortment
More informationFire-Rated Doors and Hardware. A Guide to Field Inspection
Fire-Rated Doors and Hardware A Guide to Field Inspection Foundation s Mission To promote secure and safe openings that enhance life safety Awareness To be a source of information through awareness campaign
More informationResidential Garage Door Terminology
A Air Infiltration: The leakage or passage of air through a door system Anodize: A hard non-corrosive oxide film on the surface of aluminum Astragal: A compressible or deformable seal provided on the bottom
More informationFire-rated Aluminum Doors
Fire-rated Aluminum Doors Langebjergvænget 13 ALUFLAM has pioneered the innovative solution to what was long considered an impossible dream (and a barrier to truly beautiful commercial architectural design),
More informationSecurity steel door dw 52-1 Teckentrup DF WK 2 optionally with glazing/ventilation grille
Security steel door dw 52-1 Teckentrup DF WK 2 optionally with glazing/ventilation grille Text example Compile and tender according to requirements. Please refer to technical data below for respective
More informationCode of Practice for fire resisting metal doorsets
COP 1005 Code of Practice for fire resisting metal doorsets Scope The aim of this document is to provide guidance on the best practice for, and a better understanding of, hinged or pivoted fire resisting
More informationSimplex 1000 Series. All Simplex Controls are less I.C. core. 1000 Series packed with both ASA and T strike.
Kaba Mechanical Lock Price Book, May 1, 2015 Simplex 1000 Series All Simplex Controls are less I.C. core. 1000 Series packed with both ASA and T strike. KNOBS 26D 05 03 1011 Standard Access Control 450.50
More informationInstallation Instructions and Ordering Information
The Flush Finish Trimless Door Frame Installation Instructions and Ordering Information CLEAN LINES! The Flush Finish Door Jamb System Manufactured by STUDCO Building Systems Step 1 Verify if you are using
More informationCERTIFICATE OF APPROVAL No CF 291 SCHOTT UK LIMITED
CERTIFICATE OF APPROVAL No CF 291 This is to certify that, in accordance with TS General Requirements for Certification of Fire Protection Products The undermentioned products of Drummond Road, Stafford.
More informationIntegral Kit Instructions
Integral Kit Instructions For Fisher & Paykel Cabinet widths of 525, 635, 680, 790 mm wide For curved door Models Series B, C, D & G Manual 814980 Updated August 2008 IMPORTANT If your refrigerator has
More informationA ROAD MAP FOR YOUR CODE, SMOKE BARRIER & SMOKE PARTITION REQUIREMENTS
A ROAD MAP FOR YOUR CODE, SMOKE BARRIER & SMOKE PARTITION REQUIREMENTS International Code Council National Fire Protection Association Underwriters Laboratories Inc. 5203 Leesburg Pike, Suite 600 1 Batterymarch
More informationCLEAR-DIVISIONS APERTO
CLEAR-DIVISIONS Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS moveable glass wall system. The yellow highlighted areas in the
More informationAstragal: a vertical member placed at the meeting edges of a double door to provide a weather seal and may be used to anchor the fixed door.
Window and Door Dictionary AAMA: American Architectural Manufacturers Association. A national trade association that establishes voluntary standards for the window, door, and skylight industry. Ambient
More informationREQUEST FOR QUOTE. Material $ Labor/Installation $ tax $ Total $ Material $ Labor/Installation $ tax $ Total $
REQUEST FOR QUOTE Specifications- Knightdale Station Park Naming Rights Exterior Signage General Conditions 1. Delivery of signs to be within 6 weeks of order confirmation. 2. Shop drawings are required
More informationBasic Technical Fundamentals of Builders Hardware Mortise, Bored and Auxiliary Locks
Mortise, Bored and Auxiliary Locks Copyright 2002, 2009, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Table of Contents Page SARGENT History...................................................
More informationCATALOGO PRODOTTI PORTONI INDUSTRIALI COIBENTATI
CATALOGO PRODOTTI PORTONI INDUSTRIALI COIBENTATI The Company Founded in 1973 by Mr Imes Tinti in association with his son Vanni Tinti. In 1999 the locksmith workshop became a modern industrial company
More informationglass & Glazing Products
glass & Glazing Products WallMaker Create an unlimited variety of bright, beautiful and secure interior environments with the easy-to-install Stylmark WallMaker glass wall system. This versatile system
More informationA site plan or floor plan clearly identifying the location(s) of all new replacement window(s)
WINDOW REPLACEMENT GUIDELINES Community Development Planning & Building 2263 Santa Clara Ave., Rm. 190 Alameda, CA 94501-4477 alamedaca.gov 510.747.6800 F: 510.865.4053 TDD: 510.522.7538 Hours: 7:30 a.m.
More informationNovoferm Interior Doors and Frames Just what you re looking for
Novoferm Interior Doors and Frames Just what you re looking for Contents Novoferm interior doors 3 Super-Standard, Super-Plus, Super-Dekor and Super-Color interior doors 4 Also suitable for use as a magnetic
More informationTS93 EMR T/PT/TDE. Surface applied door closer
TS EMR T/PT/TDE Surface applied door closer Installation instructions: Pull side track mount door closer with smoke detector (EMR T) Push side track mount door closer with smoke detector (EMR PT) Double
More informationDISTRIBUTOR TECH DATA
Ceco Door Products DISTRIBUTOR TECH DATA Distributor Tech Data INDEX SECTION 11 - FRAMES, GENERAL Technical Information: Prime Paint Data.........................................................11-002
More informationPremier & Deluxe 3-Season Room Sliding Glass Door
DTSSGD-11 Premier & Deluxe 3-Season Room Sliding Glass Door Installation Instructions Screen Door Seal Left Side Track Top Track Assembly Right Side Track Right Side Trim Sliding Glass Door Sliding Screen
More informationCore and Frame Details
and Frame Details February, 2014 Contents Architectural Flush Wood Door Codes 1-2 Performance Standards 3 GRAHAM SUPREME DOOR GSD SR 35-40 4 GSD SR 41-45 5 GSD SR 31, 33, 39, and 44 6 GSD SR 46-47 7 GRAHAM
More informationSHUTTER PROGRAM. www.royalwindowsinc.com CORPORATE OFFICE. 606 Fountain Parkway, Grand Prairie TX 75050
SHUTTER PROGRAM www.royalwindowsinc.com CORPORATE OFFICE 606 Fountain Parkway, Grand Prairie TX 75050 Tel 214.412.1189 or 800.872.2693 Fax. 214.412.1188 or 800.422.2693 Email : sales@royalwindowsinc.com
More informationBasic Technical Fundamentals of Builders Hardware
Basic Technical Fundamentals of Builders Hardware Mortise Locks Bored Locks Auxiliary Locks Inside Cover (blank) Table of Contents SARGENT History...4 Basic Name of Products...5, 6 Doors (A Brief Review)...7
More informationTable of Contents. IV. Interior Doors. 1. Product Training 2. Bilco Quote/Order Checklist
Table of Contents IV. Interior Doors 1. Product Training 2. Bilco Quote/Order Checklist Interior Doors (non-drainage units) 1. Bilco T, TD, K, and KD Type doors A. T - single leaf aluminum construction
More informationARTS AND CRAFTS 10.1.0. 5410 (open) 5412 (doors) H : 84" Tote Tray Storage. Damp Storage. Tote Tray Storage. Notebook Board Storage, Doors
Drawing Board Storage, Open Drawing Board Storage, Doors Drawing Board Storage Notebook Storage, Open 1670 D : 23.25" holds 32 drawing boards 1 shelf, adjustable on 1¼" increments maximum board height
More informationPERFORMANCE TEST REPORT. Rendered to: GLASSCRAFT DOOR COMPANY
Architectural Testing PERFORMANCE TEST REPORT Rendered to: GLASSCRAFT DOOR COMPANY SERIES/MODEL: Mahogany Entry Door PRODUCT TYPE: 6' x 8' Double Outswing Hardwood TDL Door with Half Circle TDL Transom
More informationMODEL HSR-007 Direct Drive Rolling Steel
MODEL HSR-007 Direct Drive Rolling Steel 200 Fairview Road, Unit #2, Barrie, Ontario L4N 8Z8 Tel: 866-792-9968 or 705-792-9968 Fax: 705-735-9564 www.tnrdoors.com email: info@tnrdoors.com Model HSR-007
More information280+ Mortise Mounted Series Shear Locks Special Application Solution
280+ Mortise Mounted Series Shear Locks Power Plus control module overcomes gaps of up to 1/4" Low Temperature Operation 280+ TRD Locknetics provides the industry s most complete selection of electromagnetic
More informationCHECKLIST FOR DOOR HARDWARE
CHECKLIST FOR DOOR HARDWARE HINGES: Except for residential and light commercial use all hinges should be ball-bearing/oil impregnated type Hinges on exterior doors should be non-ferrous with non-removable
More informationSECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS
SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS Display hidden notes to specifier by using Tools / Options / View / Hidden Text. On newer versions of Microsoft Word
More informationSpecialty Closers. High-End Residential High-End Security Gate Solutions
Specialty Closers High-End Residential High-End Security Gate Solutions TABLE OF CONTENTS General Information... 3 How to Select Product... 4 Options... 5 Certifications... 6 Limited Warranty... 6 Specifications...
More informationGuidelines for Windows and Doors
Guidelines for Windows and Doors WINDOWS AND DOORS Windows and doors typically comprise at least one quarter of the surface area of exterior walls of most historic buildings. Windows and doors, in addition
More informationNarrow stile lock 1314
3 2 4 6 6 1 3 2 4 4 5 3 2 4 3 5.... ( (. ). ) 11 12 5 3 5 4 8 1 6 20 8.5 6.5 19 Backset 15 3 5 2 1 5 2 5 5 0 8 9 2 8 1 1 21-1mm 12 8 24 1 6 8 1 ( 9 2 5 ) ) ). ) Narrow stile lock 1314 CE EN 12209 2 4 5
More informationRelevant British, European and International standards
Relevant British, European and International standards BS 1245:1975 Specification for metal door frames (steel) BS 3621:2007 + A1:2009 Thief resistant lock assemblies - Key egress BS 476-20:1987 Fire tests
More informationFor Two Decades CleanSeal Industry Standard Through Customer Expectations.
For Two Decades CleanSeal Industry Standard Through Customer Expectations. 45 years of innovative design and unmatched reliability in the manufacture of high performance door systems. Headquartered in
More informationHinge Replacement & Hinge and Hardware Adjustment Guide for Andersen Frenchwood Hinged Patio Doors Manufactured Before November 2005
Hinge Replacement & Hinge and Hardware Adjustment Guide for Andersen Frenchwood Hinged Patio Doors Manufactured Before November 2005 For ease of installation and continued enjoyment of your Andersen product,
More information5.1. Smoke Sealing. General: The test procedure for smoke sealed doorsets is given by reference to BS476 Section 31.1.
v8 5.1 General: The test procedure for smoke sealed doorsets is given by reference to BS476 Section 31.1. The performance criteria for smoke sealed doorsets is given by reference to BS5588 (and BS9999)
More informationArchitectural Specifications* MODEL HDE
MODEL HDE 200 Fairview Road, Unit #2, Barrie, Ontario L4N 8Z8 Tel: 866-792-9968 or 705-792-9968 Fax: 705-735-9564 www.tnrdoors.com email: info@tnrdoors.com TNR Model HDE Tech Specs September 4, 2012 Page
More informationWhy Steel? Performance Study of Steel Doors and Frames Compared to Other Materials. September 2015. Sponsored by SDI, HMMA, CSDMA
Why Steel? Performance Study of Steel Doors and Frames Compared to Other Materials September 2015 Sponsored by SDI, HMMA, CSDMA CANADIAN STEEL DOOR MANUFACTURERS ASSOCIATION L'ASSOCIATION CANADIENNE DES
More informationVinyl Patio Door Systems
Vinyl Patio Door Systems Swing Patio Door Multi-point locking system anchors the door in three separate points along the door length. Activating the deadbolt lock provides maximum security. Swing Patio
More informationType 1, 3, & 3R Enclosures
Junction oxes Type 1 Screw over....................................................................... 50-53 Junction oxes Type 1 Hinge over........................................................................
More informationFSD35, FSD36 AND FSD37 COMBINATION FIRE and SMOKE DAMPERS
3900 Dr. Greaves Rd. Kansas City, MO 64030 (816) 761-7476 FAX (816) 765-8955 INSTALLATION INSTRUCTIONS FSD35, FSD36 AND FSD37 COMBINATION FIRE and SMOKE DAMPERS 11/2 HOUR UL555 RATED UL555S LEAKAGE RATED
More informationFeatures. Optional Features
AUGUST, 2006 190/350/500 STANDARD ENTRANCES 1 FEATURES Features 190 narrow stile has 2-1/8" vertical stile, 2-1/4" top and 3-7/8" bottom rail 350 medium stile has 3-1/2" vertical stile, 3-1/2" top and
More informationFIRE/LIFE SAFETY CLOSERS/HOLDERS SERIES
FIRE/LIFE SAFETY CLOSERS/HOLDERS SERIES PRODUCT SELECTION GUIDE SENTRONIC Series LCN closer/holders combine heavy duty closers with electrically controlled hold-open functions to control fire and smoke
More informationLift-off hinge. Rising hinge. Standard hinge. Heavy duty hinge. Parliament hinge. Spring hinge. Double action spring hinge. Concealed mortise hinge...
Door Hinges Contents Butt hinges Lift-off hinge Rising hinge Standard hinge Heavy duty hinge Parliament hinge Spring hinge Double action spring hinge Concealed hinges Concealed mortise hinge... Pivot
More informationAMERICAN GOTHIC PLAYHOUSE
AMERICAN GOTHIC PLAYHOUSE Project Plan #856 Sheet 1 of 5 Pick a spot and get started with the beautiful that your kids will love. The design of the playhouse includes 35 square feet of interior space plus
More informationInstallation Guide for Andersen Architectural Wood Inswing Entry Doors
Installation Guide for Andersen Architectural Wood Inswing Entry Doors Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are
More informationPHA 2000 PHB 3000 EXIT PAD
PHA 2000 PHB 000 EXIT PAD Panic Hardware in Contur Design PHA 2000 PHB 000 EXIT PAD THE MODULAR PANIC HARDWARE-SSTEM IN CONTUR DESIGN Prior knowledge of how to open the escape door is not expected. DANGER
More informationDecorative Lever Designs
Decorative Lever Designs 3 & C 4 & K 12 14 & D 15 & A 16 & B 17 50 51 52 53 54 55 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 2 www.stanleysecuritysolutions.com
More informationAdvantage Pre-Assembled Doors & Frames
Technical Data Series Revised: 28 February, 2012 Page 1 of 23 Table of Contents Article I. SECTION 1.01 SPECIFICATIONS... 3 (a) Door Specifications... 3 (b) Frame Specifications... 3 (c) Door and Frame
More informationWalking and Working Surface Checklist:
Walking and Working Surfaces Purpose: This information is presented to improve the level of safety in our operations, and to inform you that we will comply with the OSHA Standard 29 CFR 1910.23. Responsibility:
More informationSpecifications for Standard Steel Doors and Frames (SDI-100)
Revision of ANSI/SDI A250.8-2003 Specifications for Standard Steel Doors and Frames (SDI-100) ANSI/SDI A250.8-2014 SPONSOR Steel Door Institute Approved June 2, 2014 This page left intentionally blank.
More informationRef: GA13UK Glass Awning Support System
Ref: GA13UK Glass Awning Support System Give any entrance an uncomplicated, graceful look, enhancing the design of any building. Installation LAMINATED TOUGHENED GLASS High grade 316 stainless steel for
More informationApproved Document Q: Security
Approved Document Q: Security Requirement Q1 Unauthorised access Consultation draft September 2014 1 The approved documents What is an approved document? The Secretary of State has approved a series of
More information19 DYNAmax Free Standing Server C A B I N E T s
9 DYNAmax Free Standing Server C A B I N E T s 9 DYNAmax Free Standing Server Cabinets FAMILY W=600mm and W=800mm DYNAmax Series Free Standing Server Cabinets DYNAmax series Servering Enclosures, provide
More informationC. Codes and References: Comply with the version year adopted by the Authority Having Jurisdiction.
SECTION 081216 - INTERIOR ALUMINUM DOORS AND FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationPART 1 GENERAL 1.1 SECTION INCLUDES
J-1 Section 09110 Long Form Specification INTERIOR METAL STUD FRAMING This section includes lightweight, usually 0.036 inch (0.9 mm) thick or lighter, non-axial load bearing metal stud framing including
More informationArchitectural Hardware Design Guide High-performance hardware for the most demanding architectural applications
08710/STA BuyLine Architectural Hardware Design Guide High-performance hardware for the most demanding architectural applications Architectural Hardware Design Guide The full range of Stanley hinges provides
More informationSTEEL-RITE II or III COMMERCIAL SECTIONAL DOOR Owner s Manual Supplement Model 52242 NOTICE TO USER
STEEL-RITE II or III COMMERCIAL SECTIONAL DOOR Owner s Manual Supplement Model 52242 NOTICE TO USER Thank you for purchasing the Steel-Rite II or III, model 52242 commercial sectional door from RITE-HITE
More informationSliding and Folding Door Fittings Sliding Door Accessories
Sliding door lock Toplock For 1- and 2-leaf sliding doors Suitable for toughened safty glass and laminated sheet glass Suitable for DIN left and DIN right Max. weight per door leaf 120 kg For glass thickness:
More informationCOASTAL SERIES. 316 Solid Stainless Steel Door Furniture
COASTAL SERIES 316 Solid Stainless Steel Door Furniture DORMA COASTAL SERIES SOLID STAINLESS STEEL ROSE AND PLATE DOOR FURNITURE DORMA in Australia and New Zealand is developing into a leading manufacturer
More informationPanic Exit Devices. We take the worry out of protecting what s valuable to you. Lockwood: no worries. www.lockweb.com.au
Panic Exit Devices We take the worry out of protecting what s valuable to you. Lockwood: no worries www.lockweb.com.au Contents 9000/9100 Series 9300/9400 Series 9500/9600 Series 9000/9100 Series Rim Type
More information