NOTE** VERY IMPORTANT!! WARRANTY VOID!!

Size: px

Start display at page:

Download "NOTE** VERY IMPORTANT!! WARRANTY VOID!!"

Wesley O’Neal’
7 years ago
Views:

1 NEON-FLEX Step 1: Measure area where NEON-FLEX will be installed. Step 2: install mounting track or clips as required; secure with proper screws for material that track is being mounted to (wood, concrete, metal etc.) Step 3: Measure and cut NEON-FLEX extrusion to length. NOTE** NEON-FLEX can only be cut at the cut marks stenciled on the side of the product. Cutting elsewhere will cause sections of the NEON-FLEX to not light properly. NEON-FLEX colors RED, ORANGE & YELLOW are marked and can be cut in 2.5-foot(120v) & 4 (24v) increments. BLUE, GREEN, WHITE & RGB colors are marked and can be cut in 1.5 foot (120v) & 3 (24v) increments. Step 4: Note which end of extrusion power cord will go on. 2/4 connection holes on end of extrusion will match 2/4 holes on power cord end cap (see drawing). Start at one end and start pushing base of extrusion into mounted track, leaving about on each end for end cap and power cord cap. Step 5: Place male pin connector into end of extrusion power cord will go on (pointed pins goes into extrusion rounded pins into power cord. Place power cord onto male pin connector and plug into a GFI 110v/120v outlet. Surge Protection is recommended. AVOID EXCESSIVE FLEXING & TWISTING OF PRODUCT-Surge Protection is recommended. NOTE** VERY IMPORTANT!! WARRANTY VOID!! For all outdoor installations or installations where moisture may be possible; all end caps, power cord caps, and all splice connections MUST be sealed water-tight with outdoor waterproof silicone adhesive. (Most silicones take 24hrs to fully cure so we recommend checking all connections after installation periodically. Water/moisture will cause failures. Water/Moisture intrusion is NOT covered under Warranty. We recommend using PVC glue to attach end caps and power cord caps and then sealing edges with silicone then use provided shrink tubing and silicone edges of that after heating. For all splice connections you must put silicone on both sides of the connection and allow 24hrs for full cure. (See pictures)

2 END CAP INSTALLATION POWER CORD INSTALLATION SPLICE INSTALLATION

4 NOTE** Cutting Convex installation NEON- FLEX MATERIAL HAS A MINIMUM BEND RADIUS OF 2 ONLY FOR INSTALLA- TION Straight installation Concave installation Curve installation 90-degree installation 180-degree installation

5 LED WARRANTY a. Policy Overview: Christopher International, Inc. warrants all its products, including LED modules and power supplies, to be free of defects in material and workmanship during the warranty period. The customer will process warranty service with Christopher International, Inc. s distributor or authorized retail store if purchased from them. The warranty is not subject to abuse, misuse or transfer. Christopher International, Inc. reserves the option to repair or replace products at no charge if found to be defective during the warranty period. Christopher International, Inc. s liability under the warranty is limited to repair or replacement of the unit and does not include the transportation cost. In no events will Christopher International, Inc. be liable for interruption of business, loss of profits, or indirect or consequential damage, injury to person or damage to property from any cause whatsoever. b. Warranty Period: One year from the date of original purchase. (For all products) c. Return Procedure: Before returning the product to Christopher International, Inc., the customer should call (321) first to receive return authorization. The defective product must be sent to the address below with a dated sales receipt as proof of purchase before the expiration of warranty period. Damage during transit is not covered by this warranty. Christopher International, Inc Dow Rd. Suite 12 Melbourne, Florida 32934

Assembly Guide FOR LED NEON FLEX

Assembly Guide FOR LED NEON FLEX It s not neon it s better! 1040 Avenida Acaso, Camarillo, CA 93012 Phone: (800) 336-6500 ext. 519 Fax: (805) 388-7950 Email: info@californeon.com Website: http://www.californeon.com