THERMAFLEX FLEXIBLE DUCT

Transcription

1 INDEX COMMERCIAL HVAC INSULATED AND NON-INSULATED DUCT FIBERGLASS CLOTH FLEX NON-INSULATED MODEL ST-L FIBERGLASS CLOTH FLEX NON-INSULATED MODEL S-LP-10 AIR CONNECTOR FOIL FLEX NON-INSULATED MODEL S-LD AIR CONNECTOR INSULATED FLEX MODEL M-KE ACOUSTICAL AIR DUCT INSULATED FLEX MODEL G-KM AIR DUCT RESIDENTIAL HVAC FLEX-VENT FOIL FLEX NON-INSULATED MODEL MC AIR CONNECTOR INSULATED FLEX MODEL KP AIR DUCT Expert Service. Quality Products. Since

2 INSULATED AND NON-INSULATED DUCT FOR COMMERCIAL HVAC The Pro Series flexible duct products are the most reliable and durable products in the commercial HVAC industry. All products are GreenGuard. Advantages Reduced total installed cost fast economical installation. Superior insulation and thermal performance. Easily shaped to fit oval inlets and fittings. All components are self-extinguishing and will not support flame. Certified UL 181 & NFPA 90A and 90B for US and Canada Complies with most state and federal standards or codes. Unique construction will not unravel when cut. Suitable for air venting and drying applications. May help contribute to meeting LEED requirements. INSULATED FLEX MODEL M-KE ACOUSTICAL AIR DUCT The M-KE Acoustical Duct offers exceptional sound control. Its acoustically rated chlorinated polyethylene (CPE) core allows sound energy transmission through the core and insulation, and into the plenum space. A highly efficient, self-extinguishing duct, the M-KE is suitable for use in all pressure heating and cooling systems M-KE M-KE M-KE M-KE M-KE M-KE M-KE M-KE M-KE M-KE M-KE Temperature Range: R-Value: 4 20 inches ID 10 inches (4" 12" ID) 6 inches (14" 16" ID) 4 inches (18" 20" ID) 1 inch (4" 12" ID) 1/2 inch (14" 20" ID) -20 F to 200 F cont. -20 F to 250 F intermittent R-4.2, R-6.0, R

3 INSULATED FLEX MODEL G-KM AIR DUCT Highly efficient, thermally insulated flexible duct for use in low and medium pressure heating and cooling systems. Acoustically rated, self-extinguishing CPE core easily expands over fittings. Core is permanently bonded to a coated spring steel wire helix that supports an ample blanket of fiberglass insulation over a fiberglass scrim and a tough polyethylene vapour barrier. Smooth liner, insulation, and tough vapour barrier provide even airflow and a double air seal G-KM G-KM G-KM G-KM G-KM G-KM G-KM G-KM G-KM G-KM G-KM G-KM G-KM AVAILABLE IN SIZES FROM 2" TO 20" Temperature Range: R-Value: 3 20 inches ID 6 inches (3" 16" ID) 4 inches (18" 20" ID) 1 inch (4" 12" ID) 1/2 inch (14" 20" ID) -20 F to 200 F cont. -20 F to 250 F intermittent R-4.2, R

4 FIBERGLASS CLOTH FLEX NON-INSULATED MODEL ST-L Non-insulated UL 181 Class 1 flexible air duct, extremely strong with heavy fiberglass cloth fabric permanently bonded to a corrosion resistant spring steel wire helix. For low to high pressure heating and cooling systems. A superior alternative in applications where insulated duct is not required or cannot be used, e.g., clean room applications. Unlike connector-rated products, S-TL is not limited to length of run STL STL STL STL STL STL inches ID 16 inches (2" 10" ID) 10 inches (12" 20" ID) 1 inch (2" 20" ID) 6000 FPM FOIL FLEX NON-INSULATED MODEL S-LD AIR CONNECTOR Non-insulated air connector with a reinforced metallized film laminate jacket, permanently bonded to a corrosion resistant coated spring steel wire helix. For all pressure heating and cooling systems. An economical alternative where insulated duct is not required S-LD S-LD S-LD S-LD S-LD S-LD S-LD S-LD S-LD CLASS 1 CONNECTOR 3 14 inches ID 10 inches (3" 14" ID) 1 inch (3" 14" ID)

5 FIBERGLASS CLOTH FLEX NON-INSULATED MODEL S-LP-10 AIR CONNECTOR Non-insulated air connector with extremely strong woven fiberglass fabric with flame retardant coating, permanently bonded to a corrosion resistant coated spring steel wire helix. For all pressure heating and cooling systems. A superior alternative in applications where insulated duct is not required, or cannot be used SLP SLP SLP SLP SLP SLP SLP SLP SLP SLP inches ID 10 inches (2" 14" ID) 1 inch (2" 14" ID) CLASS 1 CONNECTOR

6 FLEX-VENT FOR RESIDENTIAL HVAC Flex-Vent offers a complete line of high-quality, value-priced duct products. There s no better product line for the money. Advantages Reduced total installation cost - fast, economical installation. Certified UL 181 & NFPA 90A and 90B for US and Canada. Superior insulation and thermal performance. Easily shaped to fit over all inlets and quickly connects to fast fittings. Unique construction will not unravel when cut. INSULATED FLEX MODEL KP AIR DUCT Strong polyester film laminated and encapsulating a heavy, corrosion-resistant steel wire helix, forms the inner core and supports a thick blanket of fiberglass insulation over a fiberglass scrim. The outer vapour barrier is a jacket of durable black polyethylene. Designed for low to medium pressure systems KP KP KP KP KP KP KP KP KP KP KP KP Temperature Range: R-Value: 4 20 inches ID 10 inches (4" 16" ID) 6 inches (18" 20" ID) 1/2 inch (4" 20" ID) -20 F to 250 F cont. R-4.2, R-6.0, R

7 FOIL FLEX NON-INSULATED MODEL MC AIR CONNECTOR Use this non-insulated and economically priced flexible connector in medium to low pressure air conditioning systems and in air venting and drying applications. The corrosion resistant spring steel wire helix is laminated with multiple layers of clear and metallized polyester film, fully laminated with adhesive. Oversized for quick installation MC MC MC MC MC MC MC MC MC inches ID 10 inches (3" 20" ID) 1 inch (3" 12" ID) 1/2 inch (14" 20" ID)