INSTALLATION INSTRUCTIONS
|
|
- Nicholas Scott
- 7 years ago
- Views:
Transcription
1 INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII S 2007 RIDGELINE Issue Date MAY 2006 PARTS LIST Relay Fog Light Kit P/N 08V31-SJC-100 Right fog light 15 Wire ties Left fog light 2 Wire ties with clips (black) 5 Wire ties with clips (white) Right trim Relay bracket Left trim 2 Washer-bolts, 6 x 12 mm 2 Flange nuts, 6 mm Fog light harness 10 Self-tapping screws, 5 x 16 mm Switch harness 4 Screw grommets 4 Self-tapping screws, 5 x 12 mm (black) 20A Fuse block Fuse label 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII (0605) 08V31-SJC of 16
2 Ground bolt Illustration of the Fog Lights Installed on the Vehicle 20A FUSE BLOCK Small wire ties RELAY Switch Kit (sold separately) P/N 08V31-SJC-120A (NH-574L, Warm Gray) 08V31-SJC-130A (NH607L, Dark Gray) Fog light switch RIGHT FOG LIGHT LEFT K TOOL AND SUPPLIES REQUIRED #2 Phillips screwdriver Flat-tip screwdriver 10 mm Combination wrench 10 mm Socket Ratchet File Eye protection (face shield, safety goggles, etc.) Diagonal cutters Utility knife Pushpin Drill Shop towel Hacksaw blade 3 mm and 5 mm Drill bits 40 mm Hole saw Blanket INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 1. Make sure you have the anti-theft code for the radio, then write down the radio station presets. 2. Disconnect the negative cable from the battery. 2 of 16 AII (0605) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
3 Cutting the Front Bumper 3. Remove the front bumper. Remove the seven clips along the top of the front bumper and radiator cover. Remove the two clips, six bolts and two selftapping screws, and remove the front bumper. Place the front bumper on a blanket. 4. On the inside of the front bumper, locate the fog light identification marks on the left side. Using a pushpin, mark the front bumper at each of the eight marks as shown. IDENTIFICATION MARKS (8) CLIPS (7) PUSHPIN 3 mm DRILL BIT 40 mm HOLE SAW BOLT (6) SELF-TAPPING SCREWS (2) H K 5. While wearing eye protection, drill eight 40 mm holes through each mark on the front bumper. First drill with a 3 mm bit, then finish with a 40 mm hole saw. 6. Using a hacksaw blade, cut out the front bumper along the line between the holes. Remove any burrs from the edge of the hole with a file. Cut out area LINE HACKSAW BLADE K 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII (0605) 3 of 16
4 7. Using a pushpin, mark the front bumper at each of the two marks below the fog light opening. While wearing eye protection, drill one 5.5 mm hole through each mark. First drill with a 3 mm drill bit, then finish with a 5.5 mm drill bit. Remove any burrs from the edge of the holes. 10. Attach the left fog light to the front bumper with two 5 x 16 mm self-tapping screws and two 5 x 12 mm self tapping screws (black). 5.5 mm DRILL BIT 5 x 16 mm SELF-TAPPING SCREW PUSHPIN IDENTIFICATION MARKS (2) K 8. Repeat steps 4 thru 7 to cut and drill the right side of the bumper. Installing the Fog Light 9. Install one screw grommet into each square hole in the left fog light bracket. LEFT FOG LIGHT 5 x 12 mm SELF-TAPPING SCREW (BLACK) K 11. Attach the left trim to the front bumper with three 5 x 16 mm self-tapping screws. LEFT TRIM LEFT BRACKET SQUARE HOLE SQUARE HOLE 5 x 16 mm SELF-TAPPING SCREWS (3) K SCREW GROMMET K 12. Repeat steps 9 thru 11 to install the right fog light and right trim. 4 of 16 AII (0605) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
5 Routing the Fog Light Harness 13. Remove the one clip that fastens the washer reservoir tank. WASHER RESERVOIR TANK 15. Release the four retaining tabs, and remove the under-hood fuse/relay box upper cover. FUSE/RELAY BOX UPPER COVER RETAINING TABS (4) CLIP K 4N19010K 14. Remove the bolt that fastens the relay box, and release the two retaining tabs. Remove the relay box. 16. Using masking tape, mark the square terminal. Remove the two terminals (one bolt for each). The masking tape functions as an installation mark. Note where each terminal attaches. RELAY BOX BOLT BOLT RETAINING TAB BOLT SQUARE MASKING TAPE RELAY BOX K ROUND 4N19020K 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII (0605) 5 of 16
6 17. Release the six retaining tabs, and remove the under-hood fuse/relay box lower cover. RETAINING TABS (6) FUSE/RELAY BOX LOWER COVER 18. Remove the coolant overflow bottle from the bracket and set it aside. Route the white terminal from the fog light harness under the right headlight and into the engine compartment. Route the fog light harness 4-pin connector along the front bulkhead. BULKHEAD WHITE FUSE/RELAY BOX K COOLANT OVERFLOW BOTTLE RIGHT HEADLIGHT 4-PIN 2-PIN K 19. Route the white terminal from the fog light harness along the vehicle harness to the under-hood fuse/ relay box. 6 of 16 AII (0605) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
7 20. On the bottom of the under-hood fuse/relay box, unplug the vehicle 18-pin connector. Release the lock on the vehicle 18-pin connector, and push the fog light harness red/green terminal into the vehicle 18-pin connector. Secure the lock on the 18-pin connector. 22. Secure the fog light harness to the vehicle harness with one small wire tie. Underside view 18-PIN Underside view FUSE/RELAY BOX 2-PIN FUSE/RELAY BOX FUSE/RELAY BOX SMALL 18-PIN Harness side view LOCK 18-PIN Harness side view 2-PIN LOCK RED/GREEN POSITION RED/GREEN 21. Reconnect the vehicle 18-pin connector into the under-hood fuse/relay box K 2-PIN WHITE OF WHITE OF K 23. Unplug the vehicle 2-pin connector. Release the lock on the vehicle 2-pin connector, and push the fog light harness white terminal into the vehicle 2-pin connector. Reconnect the lock on the 2-pin connector, and plug the vehicle 2-pin connector into the under-hood fuse/relay box American Honda Motor Co., Inc. - All Rights Reserved. AII (0605) 7 of 16
8 24. Remove and discard the vehicle bolt that fastens the vehicle bracket, and attach the fog light harness ground terminal with the new ground bolt. GROUND BRACKET GROUND BOLT 26. Reinstall the under-hood fuse/relay box lower cover, and reinstall the vehicle terminals to the relay box as shown. Be sure the square and round terminals are in their original positions. Remove the masking tape. BOLT (Discard.) BOLT SQUARE K 25. Secure the fog light harness to the vehicle harness with five wire ties. ROUND MARK 4N19020K 27. Insert the 20A fuse block into the under-hood fuse/ relay box. 20A FUSE BLOCK Top view K 20A FUSE BLOCK FUSE/RELAY BOX FUSE/RELAY BOX K 8 of 16 AII (0605) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
9 28. Attach the 20A fuse label onto the inside of the under-hood fuse/relay box upper cover. 31. Install the relay bracket to the relay with one 6 x 12 mm washer-bolt and one flange nut. 20A FUSE LABEL 6 x 12 mm WASHER-BOLT RELAY BRACKET FLANGE NUT FUSE/RELAY BOX UPPER COVER 29. Reinstall the under-hood fuse/relay box upper cover K 30. Behind the right headlight, locate the 2-pin connector blue taped to the vehicle harness, and remove the blue tape to free the connector. Plug the fog light harness 2-pin connector into the vehicle 2-pin connector. RELAY K 32. Attach the relay bracket to the vehicle frame with one 6 x 12 mm washer-bolt and one flange nut. 6 x 12 mm WASHER-BOLT RELAY BRACKET RIGHT HEADLIGHT 2-PIN FRAME RELAY FLANGE NUT 4-PIN K 2-PIN BLUE TAPE K 33. Plug the fog light harness 4-pin connector into the relay American Honda Motor Co., Inc. - All Rights Reserved. AII (0605) 9 of 16
10 34. Secure the fog light harness to the vehicle harness with four wire ties. 36. Secure the fog light harness to the bumper beam: With vehicle harness: Route the fog light harness along the bumper beam, and secure it to the vehicle harness and bumper beam with three wire ties, two white wire ties with clips, and one black wire tie with clip. Without vehicle harness: Route the fog light harness along the bumper beam, and secure it to the bumper beam with four white wire ties and one black wire tie. BLACK WITH CLIP GREEN TAPE BEAM K 35. Secure the fog light harness to the vehicle harness with one wire tie. Secure the fog light harness to the right end of the bumper beam with one black wire tie with clip at the green tape. FOG LIGHT BEAM BEAM BEAM WITH WHITE WITH CLIP WHITE WITH CLIP K BEAM BLACK WITH CLIP GREEN TAPE K 10 of 16 AII (0605) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
11 37. With an assistant holding the bumper near the vehicle, plug the fog light harness 2-pin connectors into the right and left fog light, and push the clip on the fog light harness into the hole of the right and left fog light bracket. Routing the Switch Harness 39. Remove the left dashboard side cover (seven clips). CLIP HOLE BRACKET 2-PIN CLIPS (7) LEFT DASHBOARD SIDE COVER 40. Remove the driver s dashboard lower cover: Remove the one self-tapping screw. LEFT FOG LIGHT K 38. Reinstall the one clip, two bolts and two selftapping screws to secure the front bumper. Do not install the four outboard bolts to the front bumper at this time. Release the nine clips, and pull out the driver's dashboard lower cover. Unplug the vehicle connectors and, if equipped, remove the air tube and unplug the in-car temperature sensor connector. Remove the lower cover. SELF-TAPPING SCREW IN-CAR TEMPURATURE SENSOR (If equipped) CLIP AIR TUBE DRIVER'S DASHBOARD LOWER COVER CLIPS (9) BOLT SELF-TAPPING SCREWS (2) K T 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII (0605) 11 of 16
12 41. Remove the switch lid from the driver s dashboard lower cover, and install the fog light switch into the driver's dashboard lower cover. 42. On the front of the fuse box, locate the 3-pin connector (brown), and unplug it. Release the connector lock, and push the blue terminal and yellow/ red terminal from the switch harness into the vehicle 2-pin connector. Reattach the connector lock. FUSE BOX END LID DRIVER'S DASHBOARD LOWER COVER K 3PIN (Brown) Harness side view 3-PIN (Brown) 3-PIN (Brown) LOCK YELLOW/RED YELLOW/RED BLUE K BLUE 43. Reconnect the vehicle 3-pin connector to the fuse box. 12 of 16 AII (0605) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
13 44. Route the two switch harness 5-pin connectors up to the opening in the dashboard where the cruise control switch and the VSA switch were disconnected. 5-PIN DASHBOARD LOWER COVER OPENING 47. Reinstall the driver's dashboard lower cover: Plug the VSA 5-pin connector (grey) into the VSA switch. Plug the switch harness 5-pin connector (blue) into cruise control switch, and plug the other switch harness 5-pin connector (brown) into the fog light switch. If equipped, reattach the air tube, and plug in the in-car temperature sensor connector, then reinstall the driver's dashboard lower cover. CRUISE CONTROL 5-PIN (BLUE) VSA 5-PIN (GREY) 5-PIN (BROWN) 45. Secure the switch harness to the vehicle harness with two wire ties. 46. Route the vehicle cruise control 5-pin connector (blue) down, and plug it into the switch harness 5-pin connector (blue) K 5-PIN (BLUE) CRUISE CONTROL VSA DRIVER'S DASHBOARD LOWER COVER CRUISE CONTROL 5-PIN (BLUE) VSA CRUISE CONTROL 5-PIN (BLUE) K 5-PIN (BLUE) CRUISE CONTROL 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII (0605) 13 of 16
14 48. Check that all wire harnesses are routed properly and all connectors are plugged in. 49. Reinstall all removed parts. Do not reinstall the outboard bumper bolt at this time. Check that all clips and fasteners are installed securely. 50. Reconnect the negative cable to the battery. USE AND CARE How to Operate Fog Lights Turn the light switch to the on position (headlights on low beam ). Press the fog light switch (indicator is on). 55. Pull up on the driver s window switch fully to close the window completely, then hold the switch for 2 seconds or more. 56. Test the window AUTO function. BULB REPLACEMENT 1. Remove the two bolts from the bottom of the front bumper, and pull down the inner fender. The fog light lenses can cloud when the outside temperature is cold; this is normal and should go away in warm weather. Fog Light Aiming Adjustment 51. Adjust the fog light: Pull down the inner fender. Adjust the aiming according to local laws and regulations. To adjust, turn the aiming adjustment knob in or out until the correct aiming is obtained. BOLT INNER FENDER BOLT K 2. Unplug the connector from the fog light. 3. Remove the bulb. To raise. To lower. 52. Reset the clock, and reset the radio station presets K 53. Reinstall the four outboard bumper bolts. NOTE: Whenever the battery is disconnected, the driver s AUTO function is disabled. 54. Start the engine. Push down on the driver s window switch until the window is fully open. BULB K 14 of 16 AII (0605) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
15 4. Install the new bulb into the fog light. Use only a genuine Honda halogen light bulb of specified wattage. Rating: 12V 55W H11 Halogen Light Bulb P/N: S5A-003 Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it clean with a soft cloth that has been dampened with a denatured alcohol or a mind detergent solution. Align the tab on the fog light with the cutout in the bulb when installing the new bulb. If not aligned, the fog light may annoy oncoming drivers. NEW BULB K 5. Reinstall the removed parts in the reverse order of removal. Check that the wire harnesses are not pinched. Be sure to tighten the self-tapping screw and bolts securely. 6. Check the operation of the fog light; adjust the aiming if necessary American Honda Motor Co., Inc. - All Rights Reserved. AII (0605) 15 of 16
16 CIRCUIT DIAGRAM Hot at all Times Hot with Headlight Switch in Head Hot with Headlight Switch in Park or Head RED / GRN 20A WHT RED / GRN RED / GRN RED / BLK BLU / YEL YEL / RED BLU / YEL Switch 1=Indicator 2=Switch Illmination FOG LIGHT BLK BLK BLK RED Illumination Control OFF BLK BLACK BRN BROWN YEL YELLOW ORN ORANGE LIGHT BLU BLUE PUR PURPLE OFF Low Hi GRN GREEN NAT NATURAL RED RED PNK PINK OFF ON ON - WHT WHITE GRY GRAY LT BLU LIGHT BLUE LT GRN LIGHT GREEN 4D21820K 16 of 16 AII (0605) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26327 2004 S2000 Issue Date OCT 2004 PARTS LIST Security System: P/N 08E51-S84-100 Attachment Kit: P/N 08E55-S2A-101 2 Remote controls
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII23628 2003 PILOT Issue Date MAY 2002 PARTS LIST Security System Kit (sold separately): P/N 08E51-S84-100 2 Remote controls Attachment
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. ACCORD All 30209 2-AND 4-DOOR SYSTEM (VP, LX, SE) Issue Date AUG 2005 PARTS LIST Security System Attachment: P/N 08E55-SDA-100A Unit panel
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 24393 ACCORD (DX, LX) SYSTEM 2-AND 4-DOOR Issue Date AUG 2002 PARTS LIST Security System Attachment (LX): P/N 08E55-SDA-100A Unit panel
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. XM RADIO SYSTEM 2003 ACCORD 4 DOOR AII 24378 Issue Date MARCH 2003 The XM Radio will not fit in a vehicle equipped with a rear entertainment
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2009 PILOT Publications No. AII 39408 Issue Date MAY 2008 PARTS LIST Steering Wheel Trim (With Cruise and Audio) P/N 08Z13-SZA-130B (Chocolate) P/N 08Z13-SZA-140B
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory TRIM Application 2008 ACCORD 4-DOOR Publications No. AII 35362 Issue Date AUG 2007 PARTS LIST Steering Wheel Trim (Without Navigation) P/N 08Z13-TA0-100 Right steering
More informationInstallation instruction do88 Intercooler for Volvo S40 / V50 / C30
Installation instruction do88 Intercooler for Volvo S40 / V50 / C30 This instruction shows how to replace the OEM intercooler with our performance intercooler. 2. 3. 1. 4. 5. Part number: ICM-170 6. At
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: Illuminated Kick Plate APPLICATION: Rogue (2011) PART NUMBER: 999G6 GX010 KIT CONTENTS: Item A B C G H QTY 1 1 1 D 1 E 1 F 3 15 6 Description Kick Plate,
More informationTOYOTA TUNDRA 2015 Billet Grille w/led DRL
TOYOTA TUNDRA 2015 Billet Grille w/led DRL Part Number: 00016-34088 Accessory Code: BG3000 Conflicts Models 1794 and Platinum Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL 2 1 Driver Box 3
More informationTOYOTA Tundra 2007 - BACK-UP CAMERA SYSTEM Preparation
Preparation Part Number(s): PT233-34070, PT923-35070-11, PT923-35070-43 NOTE: Part number of this accessory may not be the same as part number shown. Back Up Monitor Kit Contents PT923-35070-11 / PT923-35070-43
More informationTOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation
TOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00112 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationKEYLESS ENTRY UPGRADE SECURITY SYSTEM for 2004 TOYOTA HIGHLANDER
KEYLESS ENTRY UPGRADE SECURITY SYSTEM for 2004 TOYOTA HIGHLANDER DEALER SERVICE AND INSTALLATION MANUAL KIT NO. 00016-30915 Contents PARTS LIST... 2 PARTS ILLUSTRATIONS... 2 VEHICLE PREPARATION... 3 INSTALLING
More informationWARNING! REQUIRED TOOLS & SUPPLIES: HIGH VOLTAGE
INSTRUCTIONS Product: GEM Electric Motorcars Models: All Subject: Instructions for installing Stereo Accessory Estimated Completion Time:.75 Hours Parts: See Page # 7 REQUIRED TOOLS & SUPPLIES: (1) 3/8
More informationInstallation Instructions
520 Installation Instructions Thank you very much for purchasing PIAA product. Please read this entire manual before installation and use of this product. For Installers Please give this Installation Manual
More informationFRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER Please read before beginning Stainless steel hardware
More informationBefore installation it is important to know what parts you have and what the capabilities of these parts are.
INSTALLATION GUIDE Before installation it is important to know what parts you have and what the capabilities of these parts are. The Recon XZT is the smallest and most powerful gauge of its kind. With
More informationSolstice/Sky Water Pump Replacement
Solstice/Sky Water Pump Replacement The water pump on the Solstice/Sky is starting to need replacement on some vehicles. This guide will help in replacing the water pump while the engine is still in the
More informationInstallation Instructions
Installation Instructions Page 1 of 16 January 2008 Equipment Parts, Trailer Hitch Ver 3.0 Accessory Development SUBJECT TRAILER HITCH KIT (US Only) - P/N 71 60 0 413 359 MODEL X5 (E70): Select Vehicle
More informationPARTS & INSTALLATION INSTRUCTIONS MEYER SNOW PLOW LIGHTS
Form 1-696 R1 January, 2003 PARTS & INSTALLATION INSTRUCTIONS MEYER SNOW PLOW LIGHTS PARTS LIST ITEM PART NO. QTY. DESCRIPTION 07033 1 SNOW PLOW LIGHT CARTON 1 07034 1 Snow Plow Light, Pass. Side (No Hardware)
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (741-306) Honda Accord 2003 07 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic
More informationCONTENTS TOOLS REQUIRED: Ratchet 13mm Socket 10mm Socket Phillips Screwdriver Pliers Panel Removal Tool. Amp Installation
CONTENTS 1EA. SUBWOOFER ASSEMBLY P/N RUWRANGLER 1EA. 200 WATT AMP/BRACKET ASSEMBLY P/N RM11JKBTL - Bracket P/N RE08BTL200R - Amp 1EA. POWER HARNESS P/N RHWRANGLERPWR 1EA. OVERLAY HARNESS P/N RHWRANGLER
More informationArctic Leash Instruction Manual Alaskan Products Company LLC.
Retractable Cord Reel for Engine Block Heaters Arctic Leash Instruction Manual Alaskan Products Company LLC. INSTALLATION INSTRUCTIONS This instruction manual is a reference guide for installing and operating
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Handle Camera Mirror Display 2004-2014 Ford F-150 and 2008-2015 Ford Super Duty (Kit part numbers 9002-9521) Kit Contents: Mirror Tailgate Handle with camera and harness Interior
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Aftermarket and Factory 5.0, 8.4 and 6.1 MyGig Touch Screen Display (Factory Display requires Chrysler/Dodge dealer to activate) 2009 Current* Dodge Ram (Kit part number 1009-6503) *NOTE:
More information2002 2005 Mini Cooper S Grille Install Instructions
2002 2005 Mini Cooper S Grille Install Instructions Lower Front Grille BEFORE AFTER Package Contents 1 perforated grille (Stiletto, RAZR, or Monster) 6 Zip Tie Mounting Pads 1 is for the temp. sensor 5
More informationCoolant heater. Thermo Top - Z/C additional heating system. Installation instructions. Volvo S60, Volvo V70, and Volvo S80 Beginning Model Year: 2000
Coolant heater Thermo Top - Z/C additional heating system Approval code ~~~ S 9 Installation instructions Volvo S60, Volvo V70, and Volvo S80 Beginning Model Year: 000 6 6 7 8 Volvo XC70 Beginning Model
More informationINSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5
CI100018 INSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5 Rabbit, Jetta 2.5L These instructions are applicable to vehicles equipped with either manual or automatic transmissions Thank you for choosing to
More informationInstallation Instructions
Installation Instructions For Use with PXPV230, PXPV265, PXPD230, and PXPD265 models Attention! - Please read these instructions completely before attempting installation. Always unplug the power supply
More informationTOYOTA PRIUS 2010- HANDS FREE BLU LOGIC Preparation
TOYOTA PRIUS 2010- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationspecializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1967-72 CHEVROLET PICKUP
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1967-72 CHEVROLET PICKUP CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect
More information2003/2004/2005 TOYOTA COROLLA
2003/2004/2005 TOYOTA COROLLA KEYLESS ENTRY UPGRADE SECURITY SYSTEM INSTALLATION INSTRUCTIONS KIT NO. 00016-30120 SPECIAL NOTE: Installation Sequences After TMS and Safety mandated preparatory steps have
More informationA&A CORVETTE PERFORMANCE C6 BOOST & FUEL GAUGE INSTALLATION INSTRUCTIONS
A&A CORVETTE PERFORMANCE C6 BOOST & FUEL GAUGE INSTALLATION INSTRUCTIONS 1. Check your gauges before you take them out of the packaging to make sure they are at 0 (zero) psi for both boost and fuel pressure.
More information1970-72 Chevelle. 1970-72 Chevelle. (500645) Gauge Cluster Kit Installation Instructions. (500645) Gauge Cluster Kit Installation Instructions
1970-72 Chevelle (500645) Gauge Cluster Kit Installation Instructions 1970-72 Chevelle (500645) Gauge Cluster Kit Installation Instructions STEP 1: There are 4 small gauges. This is a photo of the bare
More informationPOWER LOCK KIT GENERAL INSTALLATION -J04427 REV. 2007-12-04. Kit Number. Models. Additional Parts Required. Kit Contents
-J0 REV. 00--0 POWER LOCK KIT GENERAL Kit Number -0, 0-0 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harleydavidson.com (English
More informationTime needed: ~3h for lid replacement only. Add 1h for operation harness in lid and ~2h more for installing drive unit and cable harness in trunk.
DIY for replacing trunk lid and/or retrofitting electrical operation of trunk lid. This document is meant to be a support and give advice on the procedure but I will take no responsibility for any damage
More information2003 ACCORD - Automatic Transmission Removal
2003 ACCORD - Automatic Transmission Removal Special Tools Required Engine support hanger, A and Reds AAR-T-12566 Engine hanger balancer bar VSB02C000019 Front subframe adapter VSB02C000016 These special
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. DESCRIPTION: Auto-Dimming Mirror Kit with Compass and HomeLink 2. APPLICATION: Titan 3. PART NUMBER: 999L1 WS000 4. KIT CONTENTS: Item Qty Description Service
More informationADDING AN ELECTRIC AUXILIARY FAN TO RADIATOR STACK ON 03 ALPINE COACH
ADDING AN ELECTRIC AUXILIARY FAN TO RADIATOR STACK ON 03 ALPINE COACH The original design of the 03 Alpine Coaches (and perhaps other years as well) did not include any kind of engine fan engage mechanism
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Application Outboards Faria 5 Gauge Set* Publication No. Description Part Number Honda Code PII53606A White faced, flat lens 06300-ZW5-010ZB 6315410 Issue Date Black faced, flat
More informationCUSTOM AUXILIARY FORWARD LIGHTING KIT
-J0 REV. 0--0 CUSTOM AUXILIARY FORWARD LIGHTING KIT GENERAL Kit Number -0, 0000 Models This Custom Auxiliary Lighting Kit adds lamps and turn signals to 00 and later FLHX model motorcycles. Additional
More informationProjector90 Xenon Headlight Installation Guide
Projector90 Xenon Headlight Installation Guide Written exclusively for Umnitza s Projector90 Product This step-by-step guide is designed to be used in together with other available documentation including
More informationWiper Motor Marinco 2.5. Installation Instructions
Wiper Motor Marinco 2.5 Installation Instructions Wiper Motor Marinco-2.5 The Marinco 2.5 Wiper Motor Offers the Following Features: Fully sealed base and housing which allows installation in outdoor wet
More informationInstalling RNS-E SAT NAV for Audi A4
As one of the major options on the A4 you can get a DVD Satellite Navigation System call the RNS-E. With the help of ebay these sat nav systems are now available to by at a rough cost of 650 plus the cost
More informationRetrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006
Retrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006 Disclaimer: This set of instructions is simply a guide on how I installed my own heated steering
More informationMGB Chrome Bumper Conversion
MGB Chrome Bumper Conversion Installation Instructions For 1974 1/2-1980 MGB This kit requires cutting, welding, and painting. Professional installation recommended. Note: Every MGB body is slightly different
More informationSCION FR-S 2013 - PERFORMANCE AIR INTAKE Preparation 2.0L F-4
Preparation 2.0L F-4 Part Number: PTR03-18130 Please see Page 12 for important Care and Maintenance information! Kit Contents Item # Qty. Service Part # Description 1 1 PTR03-18130-AC TRD Air Box Base
More informationPart Name/Description Part Number Quantity. Power Cable 4000950-5 1
Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Power Cable 4000950-5 1 Raven Harness Adapter Kit 4100525 1 Installation Instructions
More information1999.5-2001 Audi A4 (B5) HID conversion installation instructions
1 of 5 10/26/2007 4:48 PM 1999.5-2001 Audi A4 (B5) HID conversion installation instructions Tools Needed: A drill 1" hole saw T27 Torx bit and driver with a 4" extension Extendable magnet Pliers or A drill
More informationTriac Printed Circuit Board Replacement
Technical Service Bulletin: Triac Printed Circuit Board Replacement TRONIC 5000C Pro Models: WH17, WH27, WH36 Introduction Fig. 1 ELECTRICITY IS EXTREMELY DANGEROUS. TAKE EXTRA PRECAUTIONS AND ENSURE ALL
More informationPOWER TRIM 5 F AUTO TRIM AND AUTO TRIM
POWER TRIM 5 F 22217 AUTO TRIM AND AUTO TRIM Table of Contents Page Auto Trim System........................ 5F-1 Description........................... 5F-1 Auto Trim Operation...................... 5F-2
More information4.3-inch Back-Up Camera
TM 4.-inch Back-Up Camera Model No.: PKC0BU4 Owner s Manual and Warranty Information Read these instructions completely before using this product. Retain this Owner s Manual for future reference. INTRODUCTION
More informationPart Number: 250-1859
General Applicability 2010 Honda Insight 07- Kia Optima / Forte / Rondo/ 10- Sedona / 12 Soul 10- Hyundai Tucson / Elantra Touring ETC 2012 Accent / Elantra/ Genesis Recommended Tools Safety Tools Gloves,
More informationTOOL SVC NUMBERS: 250-2598, 250-2600 SVC CONTENTS ITEM QTY DESCRIPTION PART NUMBER 1 1 CUTTING TOOL 250-2598 2 1 EXTRACTION TOOL/PART# 250-2600
07-08 TOYOTA FJ CRUISER, 05-09 SIENNA, 06-08 SCION TC PART NUMBER: 250-1732 1 CRUISE CONTROL KIT TOOL SVC NUMBERS: 250-2598, 250-2600 2 2 1 BASE KIT CONTENTS ITEM QTY DESCRIPTION 1 1 CONTROL SWITCH ASSEMBLY
More informationBoxster. Technical Information. Service 3/99 9415. Litronic Retrofit Kit
Litronic Retrofit Kit 9 3/99 9415 Binder - 9, Electrics This bulletin replaces bulletin Grp. 9, #3/99, dated 5-20-99. Vehicle Type: Model Year: Concern: Information: As of 1997 (V) Retrofitting Litronic
More informationTABLE OF CONTENTS. I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2
BAL Accu-Slide System I. Table of Contents TABLE OF CONTENTS I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2 II. GETTING STARTED... 5 - Section 2.01: Tools You Will Need... 5 - Section
More informationBUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS
BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS PLEASE READ COMPLETE INSTRUCTIONS BEFORE YOU BEGIN LEAVE INSTALLATION INSTRUCTIONS AND USER'S GUIDE WITH OWNER ALL ELECTRIC WIRING AND PLUMBING MUST BE DONE
More informationKVT-729DVD INSTALLATION MANUAL
MONITOR WITH DVD RECEIVER KVT-729DVD INSTALLATION MANUAL B54-4516-00/00 (EV) Accessories 1 0...1...1 2!...1...2 3...1 4 5...1...1 6...2 7...4 8...4 9...2 2 KVT-729DVD Installation Procedure 1. To prevent
More informationINSTALLATION INSTRUCTIONS. 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD IMPORTANT NOTES
INSTALLATION INSTRUCTIONS 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY
More informationLeft Hand Limit Switch. Housing. Left Hand. Connections. Motor Connector BROWN PURPLE GRAY BLACK DARK BLUE BLACK BROWN BROWN LIGHT BLUE.
LIGHT BLUE GRAY PURPLE Circuit Breaker Intput Circuit Breaker Output #1 Relay Left Hand Limit Switch Housing Left Hand Motor Connector Right Hand Limit Switch on Radiator Support Right Hand Limit Switch
More informationHID H4 BI-XENON FITTING GUIDE. Carefully read the following notes before starting work.
HID H4 BI-XENON FITTING GUIDE Carefully read the following notes before starting work. WARNING! This HID kit should only be installed by someone competent in vehicle wiring and electrics. Incorrect fitment
More informationPERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1967 CHEVROLET IMPALA
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1967 CHEVROLET IMPALA CONTROL & OPERATING INSTRUCTIONS The controls on your new
More informationELECTRONIC THERMOSTAT AND THERMOMETER With SPEED CONTROL
148 OLD CONCORD TURNPIKE, BARRINGTON NH 03825 USA TEL (603) 868-5720 FAX (603) 868-1040 1-800-435-6708 E-Mail:sales@seafrost.com www.seafrost.com ELECTRONIC THERMOSTAT AND THERMOMETER With SPEED CONTROL
More informationINSTALLATION GUIDE. APPLICATION LENGTH MODEL YR PART # Bestop PART #
INSTALLATION GUIDE APPLICATION LENGTH MODEL YR PART # Bestop PART # Ford Super Duty F-250 / F-350 Regular Cab (48 ) 1999 2007 10-02513-24 75102-01 Ford Super Duty F-250 / F-350 Super Cab (60 ) 1999 2007
More informationBILLET HEADLAMP WITH SHORT/TALL MOUNTS
-J099 REV. 00-0- BILLET HEADLAMP WITH SHORT/TALL MOUNTS GENERAL Kit Number 9-0, 9-0 Models Kit 9-0 is a -/ inch headlamp and kit 9-0 is a -/ inch headlamp. Both kits will fit the models listed in Table.
More informationLIFT-505. BMF Lift Kit. Yamaha Drive Gas or Electric. Installation Instructions
LIFT-505 BMF Lift Kit Yamaha Drive Gas or Electric Installation Instructions Contents of LIFT-505 Yamaha Drive BMF Lift Kit: a (1 ea.) BMF A-Arm Assembly b (1 ea.) Driver Side Shock Tower c (1 ea.) Passenger
More informationM-9424-463V Intake Manifold INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationE30 Fog Light Wiring Instructions Conversions Allowing for Independent Fog Light Operation in Sealed Beam and Ellipsoid Style Headlight Systems
E30 Fog Light Wiring Instructions X Mon Revision A 26 April, 2007 This document details the steps required to convert the headlight dependent fog lights of the E30 chassis BMW to an array of user configurable
More informationTraditional Sonar and DSI Sonar Installation
Traditional Sonar and DSI Sonar Installation This document covers the installation of the transducer and display unit installation, which includes connecting the unit to power and installing the unit on
More information1978-83 Malibu 1978-87 Monte Carlo 1978-87 El Camino
Important facts about this kit. 1. The dash panel used in this picture is used by permission of Covan's Classic. 2. This kit requires some modification to your original under dash wiring harness. It is
More informationBILLET HEADLAMP SHELL
-J008 REV. 007-07- BILLET HEADLAMP SHELL GENERAL Kit Number 770-0 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harleydavidson.com
More informationwith installation dynafact boost GAUGE this manual is for use with systems 64050-64054
owners manual with installation instructions dynafact boost GAUGE this manual is for use with systems 64050-64054 GENERAL INSTALLATION PRACTICES This manual is an installation guide for all 1. Banks DynaFact
More informationMulti Function, User Configurable Remote Vehicle Security System with 4 Button Replaceable Membrane Remote Transmitter
MODEL PRO-9744 INSTALLATION MANUAL Multi Function, User Configurable Remote Vehicle Security System with 4 Button Replaceable Membrane Remote Transmitter This System Allows The Transmitter Buttons To Be
More informationR O A D M A S T E R, I N C.
R O A D M A S T E R, I N C. 11 7 6 1 2 10 13 8 ITEM QTY NAME PART # 1...2...1/2 x 5 1/2 BOLT...350108-00 2...4...1/2 x 1 3/4 BOLT...350096-00 3...6...1/2 LOCK WASHER...350309-00 4...6...1/2 HEX NUT...350258-00
More informationUNIVERSAL LUMBAR INSTALLATION INSTRUCTIONS
UNIVERSAL LUMBAR INSTALLATION INSTRUCTIONS CONTENTS Parts List... 2 Parts Diagram... 2 Helpful Hints... 3 Installation... 4 Operation and Troubleshooting Guide... 6 Warranty Information... 8 Form #3132,
More informationTable of Contents. www.hunterfan.com. What to Expect with. Preparation. Tools Needed. Wiring. Hanging the Fan. Blades. Motor Housing.
www.hunterfan.com Table of Contents What to Expect with Your Installation 30 inches Hanging the Fan Wiring 8 Maintenance, Operation & Cleaning Light Kit 13??? 14 1 9 Troubleshooting 11 5 Blades Motor Housing
More informationSECURITY SYSTEM SMART SIREN KIT
-J00876 REV. 009-0-09 SECURITY SYSTEM SMART SIREN KIT GENERAL Kit Number 688-0 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com
More informationINSTALLATION INSTRUCTIONS. 6108 Air Spring Kit 2011+ Ford F250 Single Wheel 4WD 2011+ Ford F350 Dually 4WD (2011 F350 Single Wheel 4WD use p/n 6113)
INSTALLATION INSTRUCTIONS 6108 Air Spring Kit 2011+ Ford F250 Single Wheel 4WD 2011+ Ford F350 Dually 4WD (2011 F350 Single Wheel 4WD use p/n 6113) Thank you for purchasing a quality Hellwig Product. PLEASE
More informationBMW Parts and Accessories Installation Instructions
BMW Parts and Accessories Installation Instructions Retrofit Anti-theft Alarm System (DWA) series-identical retrofit for BMW 5 Series saloon and touring (E 9, E 9/) left-hand drive F 9 005 W Installation
More informationVOYAGER 570G. 744A Sprayer Control
VOYAGER 570G 744A Sprayer Control U S E R M A N U A L U S E R M A N U A L Table of Contents CHAPTER 1 - INTRODUCTION...1 SYSTEM CONFIGURATIONS...1 KIT CONTENTS...3 CONTROL HOUSING ASSEMBLY...5 CHAPTER
More informationFRONT TURN SIGNAL RELOCATION KIT
-J0 REV. 00-0-0 FRONT TURN SIGNAL RELOCATION KIT GENERAL Kit Number -0 Models This kit fits 00 and later Dyna model motorcycles (except FXDSE), relocating the front turn signal from the handlebars to the
More informationPost Mount Light Installation*
Post Mount Light Installation* *For the general installation of most Post Mount Spotlights, many vehicles may need slight modifications to these instructions. You will need the following tools: High torque
More informationINSTRUCTIONS FOR THE INSTALLATION AND OPERATION OF ACTIVATOR II
INSTRUCTIONS FOR THE INSTALLATION AND OPERATION OF ACTIVATOR II ELECTRONIC TRAILER BRAKE CONTROL 5500 FOR 2, 4, 6 & 8 BRAKE SYSTEMS IMPORTANT: READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY. KEEP THESE INSTRUCTIONS
More informationINSTALL INSTRUCTIONS KK-C-HVAC-1 HVAC UNIT 2003-2014 CHEVROLET/GMC VANS FOR
INSTALL INSTRUCTIONS KK-C-HVAC-1 HVAC UNIT 2003-2014 CHEVROLET/GMC VANS FOR (For NEW 2007 ALL WHITE KWIK-KITS ONLY) Warning do not attempt to install A/C units unless you are experienced with servicing
More informationMazda CX7 2007-09 99-7508
INSTALLATION INSTRUCTIONS FOR PART 99-7508 APPLICATIONS Mazda CX7 2007-09 99-7508 KIT FEATURES DIN Radio Provision with Pocket ISO Mount Radio Provision with Pocket Double DIN Mount Radio Provision Stacked
More informationWindshield Wiper System
Volkswagen Golf 5 - Windshield Wiper System Volkswagen Technical Site: http://volkswagen.msk.ru http://vwts.info Page 1 / 15 92-1 Windshield Wiper System General information The windshield wiper system
More informationAM/FM ANTENNA RELOCATION KIT
-J0 REV. 008-09-0 AM/FM ANTENNA RELOCATION KIT GENERAL Kit Number 766-09 Models This kit is used to relocate a fender-mounted AM/FM antenna to a Detachable Tour-Pak on specific model motorcycles. For model
More informationOwner s Guide and Installation Manual. Vancouver Model Name. 21321, 21328 Model No. English Español
For Your Records and Warranty Assistance For reference, also attach your receipt or a copy of your receipt to the manual. Vancouver Model Name 21321, 21328 Model No. Type A Models Owner s Guide and Installation
More informationInstrument panel. Volkswagen Touareg - Instrument panel. Special tools, testers and auxiliary items required. Release lever T10039
Volkswagen Touareg - Instrument panel Page 1 / 14 70-1 Instrument panel Tools Special tools, testers and auxiliary items required Release lever T10039 Instrument panel, removing and installing Removing
More informationPerfect Fit ELITE series IN-DASH HEAT/ COOL/ DEFROST / COMFORT 1967 CHEVROLET IMPALA
Perfect Fit ELITE series IN-DASH HEAT/ COOL/ DEFROST / COMFORT 1967 CHEVROLET IMPALA CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect Fit system. Offers complete comfort capabilities in
More informationINSTALLATION MANUAL INSIDE PASSENGER COMPARTMENT. HFC 134a FOR EUROPEAN SPEC. / GENERAL SPEC. AIR CONDITIONING ENGLISH
HFC 134a Ozone Friendly Refrigerant FOR EUROPEAN SPEC. / GENERAL SPEC. AIR CONDITIONING ENGLISH AAAMU-60 / INSIDE PASSENGER COMPARTMENT INSTALLATION MANUAL 2000 (EUROPE) B.V.. All Rights Reserved. This
More informationManual for GlobePharma Mini-Press II Rotary Tablet Press
1 of 13 Preparing the Rotary Press 1. Make sure the rotary press is unplugged. 2. Open the bottom cabinet of the rotary press and take out the grey tool kit, and the beige box of punches and dies. 3. Take
More information- power windows - alarm system - electric door mirror control - door warning light - central locking - seat memory
Door Wiring Harness Plug Connections Binder -, Electrics Vehicle Type: (86) Model Year: 7 (V) Concern: Door wiring harness plug connections X11 / X12. Information: The rubber boot for the door connector
More informationP150SC15. Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles without Sony System. 2015 Stillwater Designs P150SC15-A2-20150813
P150SC15 Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles without Sony System Subwoofer Assembly Amplifier Assembly Amplifier Harness 2015 Stillwater Designs P150SC15-A2-20150813 M6 Bolt M6
More information5 Mechanisms and accessories
5 Mechanisms and accessories 51A SIDE OPENING ELEMENT MECHANISMS 52A NON-SIDE OPENING ELEMENT MECHANISMS 54A WINDOWS 55A EXTERIOR PROTECTION 56A EXTERIOR EQUIPMENT 57A INTERIOR EQUIPMENT X79 NOVEMBER 2009
More informationAWE Tuning Air/Air Intercooler Kit for 2000-04 Audi 2.7T
AWE Tuning Air/Air Intercooler Kit for 2000-04 Audi 2.7T Congratulations on your purchase of the AWE Tuning Intercoolers for your 2.7T Audi. Hundreds of hours of design and operational testing were spent
More informationHeat Surge Model X5C Fire Place Insert Service Manual Applies to all units w/30000208 circuit board
Heat Surge Model X5C Fire Place Insert Service Manual Applies to all units w/30000208 circuit board 2012 HS M4417A BR16597R-1 HEAT SURGE 8000 FREEDOM AVE, N. CANTON, OH 44720 330-244-8161 WWW.HEATSURGE.COM
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual Supported Vehicles John Deere Sprayers 4720 4630 4730 4830 AutoTrac Ready PN: 602-0227-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW LIFT MOTOR
REMOVAL/INSTALL OF WINDOW LIFT MOTOR (742-273) Ford Expedition 1997 2002, Lincoln Navigator 1998 2002, Ford F-150 Super Crew Cab 2001 General Tech Tips: Use painter s tape rather than duct tape to secure
More information