Course Title: Wood Technology Topic/Concept: Drawing and Shop Safety Time Allotment: One week Unit Sequence: 1 Major Concepts to be learned:
|
|
|
- Susan Webster
- 7 years ago
- Views:
Transcription
1 Course Title: Wood Technology Topic/Concept: Drawing and Shop Safety Time Allotment: One week Unit Sequence: 1 1. Pictorial Drawing 2. Orthographic drawing 3. Hand Tool Safety 4. Machine Safety 5. Shop Safety 1. How to use and operate tools and machines in a safe manner 2. The student will be able to use and operate machines in a safe manner. 3.1 B, D How to draw pictorial and orthographic drawings on grid paper to scale. How to use and operate tools and machines in a safe manner Written work Evaluate classroom work. Text book Working with Wood by Bennett & Mcknight
2 Course Title: Wood Technology Topic/Concept: Machine Operations Time Allotment: One week Unit Sequence: 2 1. Operating the Table Saw 2. Operating the Radial Arm Saw 3. Operating the Jointer 4. Operating the Planer 1. How to operate each machine by where you stand and placement of hands. 2. Wearing safety glasses when operating the equipment. 3. Placement of materials on the machines. 4. Knowing the capacities of the machines 3.1 B, D Demonstrate the ability to operate the table saw, radial arm saw, jointer, and planer in a safe manner Demonstrate a safe working knowledge of how to operate the above machines. 3. Using the machines to construct required projects provided by the instructor. Evaluating Testing on the machines and evaluation of projects. Text book Working With Wood
3 Course Title: Wood Technology Topic/Concept: Student Planning Sheet Time Allotment: 3 days Unit Sequence: Types of Wood 2. Filling out the student planning sheet 3. Figuring Wood cost 1. Name and identify types of wood 2. Figure sq. foot problems. 3. Figure bd. foot problems. 4. Figure linear foot problems 5. Estimate cost for there own projects. 3.1 B, D Identify types of wood. How to figure cost. Research Written work Work sheets and student projects Text book Working with wood by Bennett & McKnight
4 Course Title: Wood Technology Topic/Concept: Gluing wood Time Allotment: 2 days Unit Sequence: Preparing wood for gluing. 2. Types of glue 3. Gluing methods 1. How to prepare edges for gluing. 2. How to work with water base glue for gluing wood projects 3. How to clamp wood with bar clamps, c clamps, strap clamps, and hand screw clamps. 4. Clean up of glued projects. 3.1 B, D What is required to edge glue and face glue a project? Use of different types of glues. 3. Use of various types of clamps Graded student projects
5 Course Title: Wood Technology Topic/Concept: Band Saw Time Allotment: 1 Day Unit Sequence: 5 1. Parts 2. Safety 3. Operation 1. Demonstrate a working knowledge of the band saw and be able to make adjustments to the various parts of the saw. 2. Operate the band saw in a safe manner. 3. The student will be able to operate the band saw to rip, crosscut, and cut out various shapes required for building a project. 4. The student will be able to resaw lumber. Identify the various parts of the band saw. Safety procedures for the band saw. Demonstrate the ability and expertise to operate the band saw
6 Course Title: Wood Technology Topic/Concept: Disk Sander Time Allotment: Time Period 1 Day Unit Sequence: 6 1. Parts 2. Safety 3. Operation 1. Demonstrate a working knowledge of the disk sander and be able to make adjustments to the various parts of the disk sander. 2. Operate the disk sander in a safe manner. 3. The student will be able to operate the disk sander for sanding various shapes required for building a project. 4. The student will be able to mount a new sanding disk Identify the various parts of the disk sander. Safety procedures for the disk sander. Demonstrate the ability and expertise to operate the disk sander.
7 Course Title: Wood Technology Topic/Concept: Drill Press Time Allotment: 1 Day Unit Sequence: 7 1. Parts 2. Safety 3. Operation 1. Demonstrate a working knowledge of the drill press and be able to make adjustments to the various parts of the drill press. 2. Operate the drill press in a safe manner. 3. The student will be able to operate the drill press for drilling holes and using a drum sander for constructing a student projects. Identify the various parts of the drill press. Safety procedures for the drill press. Demonstrate the ability and expertise to operate the drill press.
8 Course Title: Wood Technology Topic/Concept: Shaper Time Allotment: 1 Day Unit Sequence: 8 1. Parts 2. Safety 3. Operation 1. Demonstrate a working knowledge of the shaper and be able to make adjustments to the shaper for various types of cuts. 2. Operate the shaper in a safe manner. 3. The student will be able to set up and make adjustments for milling various types of cuts on the shaper. Identify the various parts of the shaper. Safety procedures for the shaper. Demonstrate the ability and expertise to operate the shaper.
9 Course Title: Wood Technology Topic/Concept: Router Time Allotment: 1 Day Unit Sequence: 9 1. Parts 2. Safety 3. Operation 1. Demonstrate a working knowledge of the router and be able to make adjustments to the router for various types of cutters. 2. Operate the router in a safe manner. 3. Operate the router in a safe manner. Identify the various parts of the router. Safety procedures for the router. Demonstrate the ability and expertise to operate the router.
10 Course Title: Wood Technology Topic/Concept: Jig Saw & Saber Saw Time Allotment: 1 Day Unit Sequence: Parts 2. Safety 3. Operation 1. Demonstrate a working knowledge of the jig saw/saber saw and be able to make adjustments to the saw for cutting operations. 2. Operate the jig saw/saber saw in a safe manner. 3. The student will be able to cut out both regular and irregular shapes on the jig saw/saber saw. 4. The student will be able to identify five different materials which can be cut on the jig saw/saber saw A, B & D Identify the various parts of the jig saw and saber saw. Safety procedures for the jig saw and saber saw. Demonstrate the ability and expertise to operate the jig saw and saber saw.
11 Course Title: Wood Technology Topic/Concept: Sanding Time Allotment: 1 Day Unit Sequence: Types of sand paper. 2. Grades of sand paper. 3. Using sand paper. 1. Be able to list the three materials which make up sand paper.(abrasive, glue, and a backing) 2. Demonstrate a working knowledge of the sand paper grading system. 3. Demonstrate the ability to use sand paper to obtain a smooth surface ready for finish. 4. Understand the concept of wet sanding 3.1 A, B, D Materials that make up sand paper. Grading system for sand paper. How to work with sand paper to smooth a surface. Text book: Working with Wood by Bennett & McKnight
12 Course Title: Wood Technology Topic/Concept: Stains and Finishes Time Allotment: 3 Days Unit Sequence: Types of stain and finishes. 2. Methods of applying stains and finishes. 3. Drying times and rubbing out finishes. 4. Safety 1. The student will be able to select the right type of stains and finishes for a project. 2. The student will be able to demonstrate how to apply stain and finish to a project the correct way. 3. The student will be able to apply stain and finish in a safe manner 4. Students will be able explain how rub out a finish to obtain a smooth finished surface. 5. Understand the concept of safety when using stains and finishes. Polyurethane, oil and lacquer base finishes. Liquid and semi gelled stains. Types of finishing equipment. Methods for attending a good finish on a project. Clean up after finishing. Safety while staining and applying finishes
13 Course Title: Wood Technology Topic/Concept: Wood Lathe Time Allotment: 1 Week Unit Sequence: Parts 2. Safety 3. Operation 4. Finishing 1. Demonstrate a working knowledge of the wood lathe and the various cutting tools. 2. Operate the wood lathe in a safe manner. 3. The student will be able to operate the wood lathe for bowl and spindle turning. 4. The student will be able to prepare stock for turning operations on the wood lathe. 5. The student will be able to sand and finish projects on the wood lathe. Identify the various parts of the wood lathe. Safety procedures for the wood lathe. Demonstrate the ability and expertise to operate the wood lathe.
14 Course Title: Wood Technology Topic/Concept: Student Projects Time Allotment: 32 Weeks Unit Sequence: Planning 2. Drawings 3. Cost Sheet 4. Construction 5. Finishing 1. Demonstrate a working knowledge of how to draw, design, plan, and figure the cost of a student wood project. 2. Operate all of the wood shop equipment in a safe manner. 3. The student will be able to assemble wood projects by use of wood screws, nails, and wood glue as required. 4. The student will be able to evaluate their projects for grading. 5. The student will be able to sand and finish projects for completion. Steps for planning projects. Steps for building and finishing a projects The student will be able to complete a self evaluation sheet of their project. Written work and written test.
How to Build a Poker Table
How to Build a Poker Table www.pokertablematerials.com 10-Person Poker Table- 96 x 48 These are step by step instructions for building a poker table. The table will measure 48" x 96" and have a 4" wide
Ladder Shelf Plans Final dimensions: 25 L x 21 W x 72 H
Ladder Shelf Plans Final dimensions: 25 L x 21 W x 72 H Copyright 2011. MLCS Woodworking. Page 1 Router bits and supplies needed: 3/8 Rabbeting bit (#10691) 1 Bottom Cleaning bit (#7941) Top and Bottom
SHELVES. www.tedswoodworking.com
SHELVES It's rare that bookshelves look as interesting as the objects you display on them. After all, how much can you decorate the edges of your shelves and sides? This unit is unusual because the shelves
Skirt 1 / 4. The Skirt. The skirt patterns were downloaded from Mark's site but they need expanding before they can be used.
Skirt 1 / 4 The Patterns The Skirt The skirt patterns were downloaded from Mark's site but they need expanding before they can be used. I used Corel Draw's real world dimensions to expand the patterns
The Hive Bodies. In the Beekeeper s Work Shop. Building a Bee Hive: The Hive Bodies. by Stephen E. Tilmann
The Hive Bodies In the Beekeeper s Work Shop The hive body is the heart of a managed bee hive colony (Figure 1). It is where the queen lays her eggs, the house bees raise the brood and the workers store
Project Instruction Booklet. CNC Milling Machine Project
CNC Milling Machine Project Instruction Booklet 1 P a g e Project Overview In this project students will learn how to use the following tools and shop materials to finish this project: personal protective
Wooden hinges for boxes using the Leigh F3 template on the D4R Pro jig.
Wooden hinges for boxes using the Leigh F3 template on the D4R Pro jig. Al Navas, Sandal Woods-Fine Woodworking Country Club, Missouri, USA Part 1 a simple prototype Direct link to the original article:
The Basics of Stave Segmented Turning
The Basics of Stave Segmented Turning Notes by Jim Rodgers Version 1.2 February, 2005 JL Rodgers, Incorporated 36 Briar Drive Martinez, CA 94553 9925) 229-5773 The Basics of Stave Segmented Turning Requirements
Wine Rack & Glass Storage Bench Chris Gardner
Wine Rack & Glass Storage Bench Chris Gardner Quantity Length Width Material Part 2 48 16 3/4 birch plywood top, bottom 2 14 16 3/4 birch plywood sides 2 14 13 3/4 birch plywood support dividers 2 3 15
Assembly Instructions Basic Folding-Leg Box Frame Style
Assembly Instructions Basic Folding-Leg Box Frame Style Basic Folding Leg Cornhole Board Concept 1 2 12 3 1 2 3 15 16 4 1 4 52 9 R1 3 4 6 21 48 12 1 4 Bolt Washer 9 13 16 35 Washer Double Nut CornholePlayers.net
MACHINING OPERATIONS AND MACHINE TOOLS
MACHINING OPERATIONS AND MACHINE TOOLS 1. Turning and Related Operations 2. Drilling and Related Operations 3. Milling 4. Machining & Turning Centers 5. Other Machining Operations 6. Shape, Tolerance and
Router Table Plans. www.bobsplans.com
www.bobsplans.com Router Table Plans Increase the capabilities of your router with this weekend project. Features a sliding fence with EZ-Mount clamps. These clamps are simple to make and grip tightly
Composite Stone Veneer
Composite Stone Veneer Installation Guide Ver 1 Jun 2015 www.compstone.com Composite Stone Veneer Installation Guide Contents Introduction & Overview 3 Required Tools 4 Optional Tools 4 Attachment Guidelines:
The tablesaw may be your shop s most valuable cutting. Crosscut Sleds. Foolproof. Innovative approach guarantees perfect results
Foolproof Crosscut Sleds Innovative approach guarantees perfect results B Y A L A N T U R N E R The tablesaw may be your shop s most valuable cutting tool, but for precise, repeatable crosscuts it needs
Making Wooden Hinges
Making Wooden Hinges By Alex Reid - www.mokkou.jp Materials and tools used - 3.2mm straight router bit - 1/8 round-over router bit - Flush-cut straight bit (with bearing on bottom) - Finger-joint jig -
COMPLIMENTARY WOODWORKING PLAN
COMPLIMENTARY WOODWORKING PLAN Adirondack Chair This downloadable plan is copyrighted. Please do not share or redistribute this plan in any way. It has been created for Wilton Tools, a division of WMH
Pepper Mill Instructions by Fred Kachelhofer
by Fred Kachelhofer I have seen Nick Cook turn a pepper mill twice and read his article posted at http://www.nickcookwoodturner.com/articles.htm (follow link and then click on Pepper Mill ). I have had
The Bonelle Tool and Cutter Grinder
The Bonelle Tool and Cutter Grinder The grinder was constructed about 1987 and exhibited at the 89th Model Engineering exhibition where it was awarded a bronze medal (see ME Vol164 No 3868 page 273). Subsequently
Build a Precision. Crosscutting Sled
Build a Precision Crosscutting Sled On-the-money, splinter-free crosscuts are well within your grasp using most well-made tablesaws, but you do have to do a few things to ensure great results cut after
Cedar Cottage Doghouse Plans
Overlapping cedar shingles add an element of charm to this medium size doghouse. The walls, floor, and trim are constructed of solid cedar, making it naturally weather resistant and provides excellent
MONTANA STATE UNIVERSITY SCHOOL OF ARCHITECTURE WOOD SHOP SAFETY MANUAL. Craft Shop Manager Bill Clinton wclinton@montana.
MONTANA STATE UNIVERSITY SCHOOL OF ARCHITECTURE WOOD SHOP SAFETY MANUAL Craft Shop Manager Bill Clinton wclinton@montana.edu 994 4402 1 Policies and Procedures 1. Eye Protection Eye protection must be
Wooden perpetual calendar plan
Project: Wooden perpetual calendar plan Page 1 of 14 Wooden perpetual calendar plan Perpetual calendar consists of movable parts, and the combinations of these parts can display any date of the year. Movable
2006 Bachelor s of Fine Arts: Glass & Ceramics, Bowling Green State University, Bowling Green, OH. EXPERIENCE
Michael Lorsung 604 Moore St. / Baton Rouge, LA 70806 Tel: 225-302-1518 / mlorsung@gmail.com EDUCATION 2006 Bachelor s of Fine Arts: Glass & Ceramics, Bowling Green State University, Bowling Green, OH.
A Simple Approach to Raised-Panel
A Simple Approach to Raised-Panel 82 FINE HOMEBUILDING Wainscot BY GARY STRIEGLER Stock molding and MDF panels transform a room 1 2 3 4 3 5 6 Raised-panel wainscot speaks of a time when craftsmen had an
HSC 2001 - Industrial Technology Band 4/5 INDUSTRIAL TECHNOLOGY FOLIO
Statement of Intent I intend to construct a slim boy which will suit my needs and will be compatible with my furniture in my bedroom in my house. This will be very handy and useful to everyone in my home.
Gate Leg Drop Leaf Table Plans
Preparing the table top blanks: Cut and glue enough 3/4 stock to make three panels 40 long by 24 wide (they will be cut to final size at a later time). While the glue dries we will work on the legs. Preparing
An Example Business Plan For Mighty Fine Millwork, Inc., a Manufacturer Focusing On Under Utilized Minor Eastern Hardwood Species
Department of Wood and Paper Science Wood Products Extension An Example Business Plan For Mighty Fine Millwork, Inc., a Manufacturer Focusing On Under Utilized Minor Eastern Hardwood Species By Harry W.
Children s Furniture Projects
This is an excerpt from the book Children s Furniture Projects by Jeff Miller Copyright 2002 by The Taunton Press www.taunton.com CHILD S ROCKER KIDS ARE ALWAYS IN MOTION. It s not easy to get them even
Raised Panel Doors Made Simple With Freud s 2+2 Raised Panel Bit Set
Raised Panel Doors Made Simple With Freud s 2+2 Raised Panel Bit Set Congratulations on your purchase of Freud s world class 2 + 2 Raised Panel Bit Set. This revolutionary design combines two small wings
Table of Contents. Class Enrollment Procedures & Cancellation Policy... 4 Cabinet Making... 6
Table of Contents Class Catalog Class Enrollment Procedures & Cancellation Policy... 4 Cabinet Making... 6 Cabinet Making 1 Build a Bookcase CM01...6 Cabinet Making 2 Wall Cabinet w/ Flat Panel Door CM02...7
Making Laminated Rolling Pins
Making Laminated Rolling Pins Introduction Why go to the trouble to make a rolling pin when you can go down to your local discount store and buy one that works just fine for less than $5? As wood turners,
Passaic County Technical Institute CARPENTRY I JANUARY 2004
Passaic County Technical nstitute CARPENTRY JANUARY 2004 CARPENTRY. DESCRPTON Freshman Carpentry is a 45 day (one marking period) course which places emphasis on introducing the student to the carpentry
WOODWORKS: ADVANCED PROJECT 2008-2009 TV STAND
WOODWORKS: ADVANCED PROJECT 2008-2009 TV STAND For advanced woodworkers, this project is a great exercise in typical cabinet construction. The case, face-frame, doors and drawer are great small-scale samples
How to Build Your Own CornHole Game
How to Build Your Own CornHole Game DIMENSIONS Here is a diagram with the basic measurements for the Cornhole board game. SUPPLIES 1/2 thick sheet of plywood one 4 x4 or two 2 x4 s 8 long 2 4 s (4) 4 1/2
a rotary transfer machine
OMNI-TURN-TRANSFER TRANSFER MACHINES INTEGRATING TURNING CENTERS BUFFOLI NORTH AMERICA (Booth #5630) takes pride in introducing the very new OMNI-TURN-TRANSFER, a patented mill-turning transfer machine
Owner's Manual & Assembly Instructions
Owner's Manual & Assembly Instructions PM01 BASE KIT Model No. FDN1014 717090311 CAUTION: SOME PARTS HAVE SHARP EDGES. CARE MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES TO AVOID A MISHAP. FOR SAFETY
OHIO University Mechanical Engineering Summary Report: Human Power System for Small Appliances and Machinery
OHIO University Mechanical Engineering Summary Report: Human Power System for Small Appliances and Machinery Appalachian Human Power Brad Bundy Ben Chovan Zach Fetchu Ed Passarrelli Ryan Tedford Will Zaylor
SHOP NOTES METAL SHAPER FOR YOUR SHOP
SHOP NOTES METAL SHAPER FOR YOUR SHOP A METAL SHAPER is indispensable for certain machining operations where flat surfaces must be produced within very close limits, such as machining flats on castings,
Introduction to JIGS AND FIXTURES
Introduction to JIGS AND FIXTURES Introduction The successful running of any mass production depends upon the interchangeability to facilitate easy assembly and reduction of unit cost. Mass production
ACCURACY PRATT & WHITNEY PRODUCTS OF 1930
ACCURACY PRATT & WHITNEY PRODUCTS OF PRATT & WHITNEY MACHINE TOOLS, SMALL TOOLS AND GAGES OF M ODERN Pratt & Whitney tools are made to the same high standards of craftsmanship which our founders established,
Classic Cajun Pirogue
Classic Cajun Pirogue Thank you for purchasing my plans. Should you have any questions while building your pirogue don't hesitate to email, unclejohn@unclejohns.com or call, 337-527-9696. I'm happy to
Hive Top Ventilation Shims
Hive Top Ventilation Shims When preparing your bee hives for the winter, it is very important to provide for ventilation at the top of the hive. Through out the winter, the bees are expelling a lot of
Easy Six Cube Bookshelf. Copyrighted Material. Page 1
Compare to: Land of Nod Cube Collection, 6 Cube Bookshelf Skill Level: Beginner Easy Six Cube Bookshelf I love the storage cubes in kids rooms because they give you an opportunity to have your children
How to Install Hardwood Flooring Over a Sub Floor
How to Install Hardwood Flooring Over a Sub Floor Installation Preparation Instructions Read the entire instructions before starting your project. 1) INSPECT EACH PLANK (see fig. a) Wood is a natural product
Building Pluto Subwoofers with Large PVC Pipe
Building Pluto Subwoofers with Large PVC Pipe I decided to make the Pluto subwoofers from 10-12 diameter PVC pipe. It seemed to me that these would be a better visual match to the Plutos themselves. The
SAFETY MANUAL. School of Architecture Building Construction Lab Florida A& M University Tallahassee, Fl (850) 599-3032. Faculty: Deborah LaGrasse
SAFETY MANUAL School of Architecture Building Construction Lab Florida A& M University Tallahassee, Fl (850) 599-3032 Faculty: Deborah LaGrasse TABLE OF CONTENTS WHAT IS SAFETY?... 2 SHOP GOALS SHOP MOTTO
Picnic Table Plans. Made out of a single sheet of plywood, it s also portable! By Kevin Ayer. This children's picnic table would
Picnic Table Plans Made out of a single sheet of plywood, it s also portable! By Kevin Ayer Materials One 4- by 8-foot sheet of 3 4-inch AC plywood Twelve 11 4-inch wood screws Primer and exterior paint
Overnight Sensations Speaker Kit
Overnight Sensations Speaker Kit Thank you for purchasing the Overnight Sensation cabinet kit. This speaker kit was precision cut using CNC machinery for the best possible fit and finish. With a little
Building an Off-Center Fixture for Turning Pendants
Building an Off-Center Fixture for Turning Pendants Turning a pendant off-center with most available metal pendant chucks means that you will have a significant amount of mass off center, which will limit
FRAMED & MOUNTED TILE MURAL
Page 1 of 5 There is no denying that tile murals have taken the sublimation industry by storm. The unique ability to take a customer s artwork or high resolution photograph, tile it using your software
Introduction to Door Construction
Entry Door Construction Made Simple with Freud s Entry & Interior Door Router Bit System Congratulations on your purchase of Freud s Entry & Interior Door Router Bit System. This unique set allows you
INTRODUCTION. Dear Business Partners,
INTRODUCTION Dear Business Partners, We are proud to issue the new catalogue of STROJFERR s.r.o. which was established in 1997 as a genuinely Czech company. In its activities and production programme,
Rudder Repair and refinish
Rudder Repair and refinish Montgomery 23 Dauntless The before photograph A receipt found inside the boat showed a previous owner had enlisted a boat yard to perform maintenance on the rudder by shortening
Chapter 3 Installing Over-the-Post Railing on an L-Shaped Stair
49 Chapter 3 Installing Over-the-Post Railing on an L-Shaped Stair In this chapter: The Over-the-Post Balustrade System Determining the Rail Centerline Using Rail Bolts Making a Pitch Block Laying Out
2.9 WINDOW & DOOR BUCKS
2.9 WINDOW & DOOR BUCKS Bucks provide attachment surfaces for windows and doors while holding back concrete from these openings during concrete placement. Mark the center and edges of openings as you place
GUIDANCE NOTE. Safe use of Woodworking Machinery (Guarding) COMMISSION. WorkSafe Western Australia COMMISSION
GUIDANCE NOTE COMMISSION Safe use of Woodworking Machinery (Guarding) 1 WorkSafe Western Australia COMMISSION Contents Basic safety rules for woodworking page 1 machines What is woodworking machinery?
Machine and Power Tool Safety Checklist. Version 1.0 June 2011. 3160 Chestnut Street, Suite 400, Philadelphia, PA 19104 215-898-4453
Machine and Power Tool Safety Checklist Version 1.0 June 2011 3160 Chestnut Street, Suite 400, Philadelphia, PA 19104 215-898-4453 Machine and Power Tool Safety Checklist Overview The purpose of this checklist
Here is your set of Detailed Plans from Copyright 2004 All Rights Reserved
Here is your set of Detailed Plans from Copyright 2004 All Rights Reserved Materials for the House Here is the list of materials you will need to construct the basic house then to cover it with roofing
HONING LATHE DUPLICATOR CUTTERS
Lay the flat face of the cutter or bit on the flat top surface of the hone with the rest of the cutter overhanging the edge. Rub the cutter or bit up and down the hone (Figure 24-44). Be sure to hold the
Free Examples of plant layout drawing
Free layout examples; a wide variety of industrial layouts, within different facility types. Principles of plant layout and design will apply widely. Free Examples of plant layout drawing Principles of
North Carolina FFA Association Agricultural Mechanics Career Development Event
North Carolina FFA Association Three (3) of the following Agricultural Mechanics Performance Skills will be selected for the state competition. North Carolina FFA Association Agricultural Mechanics Performance
Assembly GUIDE. display wine cellar kits. Required. Suggested. Questions? 888.373.6057. or visit wineracksamerica.com
Page 1 Middle Ladder End Ladder Display Tray Screwless Connector Package Contents * All models follow the same assembly procedure varying only in the number of middle ladders your rack will require. Depending
Making Clock Wheel & Pinion Cutters
Making Clock Wheel & Pinion Cutters When making hand made clocks or in repair work an odd size cutter is sometimes needed. Sometimes just one pinion is required and does not justify the cost of a commercial
TRIMMING UNIT/DIAMOND MACHINE TST.13
TRIMMING UNIT/DIAMOND MACHINE TST.13 REFERENCE BOOK rel. 02.15 TRIMMING UNIT/DIAMOND MACHINE TST.13 REL. 02.15 ENGLISH LANGUAGE 1 MACHINE DESCRIPTION TST.13 was designed and built for processing methacrylate.
WOODWORKS: BEGINNER PROJECT FISHING POLE RACK
WOODWORKS: BEGINNER PROJECT FISHING POLE RACK Storing fishing rods and reels can be quite difficult unless you have a special rack for them. Here s a simple, easy-to-build design for a rack that not only
Belt/Disc Sander. Given a properly adjusted belt/disc sander, accessories, instruction and demonstration of use, each student will be able to:
Belt/Disc Sander I. Competencies Given a properly adjusted belt/disc sander, accessories, instruction and demonstration of use, each student will be able to: A. Identify the major parts of the belt/disc
Modular Locomotive System Instruction Manual for HBK8 George Body Kit
Modular Locomotive System Instruction Manual for HBK8 George Body Kit Roundhouse Engineering Co. Ltd. Units 6-10 Churchill Business Park. Churchill Road, Wheatley. Doncaster. DN1 2TF. England. Tel. 01302
Vacuum chucking. MDAE Woodturning Center Course Number 95537001
Purpose of vacuum chucking Vacuum chucking MDAE Woodturning Center Course Number 95537001 Completing the foot of a vessel Re chucking a completed object Quick securing for additional steps (sanding) How
Product Guide SaraDrill
Product Guide SaraDrill SARADRILL / A QUICK GUIDE Drilling from solid - a proven technology to drill large diameter holes on low horse power machines. Drilling from 49mm to 270mm diameter holes from solid
DIY CABINET REFACING INSTALLATION GUIDE
DIY CABINET REFACING INSTALLATION GUIDE CABINET REFACING INSTALLATION Are you ready to reface your outdated cabinets? This guide will show you how to install your new Facelifters Cabinet Refacing Products
Hoosier Step Stool. America s leading woodworking authority. Step by Step construction instruction. A complete bill of materials.
America s leading woodworking authority Step by Step construction instruction. Hoosier Step Stool A complete bill of materials. Exploded view and elevation drawings. How-to photos with instructive captions.
Installing Window and Door Mouldings
Installing Window and Door Mouldings About Window and Door Mouldings The trim around windows and doors greatly influences the look and style of your interior. They also bridge the gaps and cover spaces
Router Table. Operating Procedures for
Operating Procedures for Router Table INTRODUCTION: The router table is a very versatile tool. It can be used to cut a molding profile, cut workpieces to match the shape of a pattern and cut a molding
Overview. Milling Machine Fundamentals. Safety. Shop Etiquette. Vehicle Projects Machine Shop
Overview Milling Machine Fundamentals Wayne Staats, UW-Madison FSAE Safety Shop Etiquette Before Machining Indicating Calculating Feeds and Speeds Machining Maintenance Safety Respect the machines Common
UNIT 1 INTRODUCTION TO NC MACHINE TOOLS
UNIT 1 INTRODUCTION TO NC MACHINE TOOLS Structure 1.1 Introduction Objectives 1.2 NC Machines 1.2.1 Types of NC Machine 1.2.2 Controlled Axes 1.2.3 Basic Components of NC Machines 1.2.4 Problems with Conventional
Skills and Knowledge Assessment Test (Section V) (SKAT) Mechanic / Machinist
INFORMATION ABOUT THE GEORGIA POWER COMPANY Skills and Knowledge Assessment Test (Section V) (SKAT) Mechanic / Machinist Four Tests will be administered: 1. Basic Machining/Mechanics Test Different types
WOODWORKS: INTERMEDIATE PROJECT 2005-2006 GARDEN BENCH
WOODWORKS: INTERMEDIATE PROJECT 2005-2006 GARDEN BENCH Traditionally made of teak, these benches have long graced English parks and gardens, aging gracefully through years of use and weather. This version
FACILITY ACCREDITATION CHECKLIST #001 APPRENTICESHIP. Rating Code: Y = Yes * N = No * R = Required * AUDIT AREA: DATE: / / HAND TOOLS Y N R
FACILITY ACCREDITATION CHECKLIST #001 APPRENTICESHIP Designated Trade: Level 1 2 3 4 Institution: Evaluator(s) / / Rating Code: Y = Yes * N = No * R = Required * * Please use a CHECKMARK under the appropriate
PROJECT PLAN. Stackable shelves
PROJECT PLAN Stackable shelves This article originally appeared in The Family Handyman magazine. For subscription information, visit www.familyhandyman.com Please note that pages that appeared in the magazine
The JIG is UP Or A couple hours up front pays in the long run.
Ed Simon Page 1 of 5 The JIG is UP Or A couple hours up front pays in the long run. A large part of the fun of beekeeping is the construction and assembly of the equipment. Since it is a hobby, I decided
INSTRUCTION FOR ASSEMBLY. 150x180 v Traditional sauna cabin
INSTRUCTION FOR ASSEMBLY 150x180 v Traditional sauna cabin 1. SAUNA PLAN 1800 LIGHT UNDER THE BENCH VENTILATION OUTLET UPPER BENCH 600 1500 LOWER BENCH 400 700 1656 956 HEATER 366 381 690 815 Light switch
WOODWORKING SAFETY MANUAL AND TEST. Woodworking Manufacturing Technologies Department (WMT) Cerritos College Norwalk, CA
WOODWORKING SAFETY MANUAL AND TEST Woodworking Manufacturing Technologies Department (WMT) Cerritos College Norwalk, CA August 2012 Table of Contents WOOD LAB SAFETY MANUAL... 2 INTRODUCTION... 2 GENERAL
DINING OUT. Build this outdoor table and bench set. TEXT AND PHOTOS BY NEAL BARRETT Photo by Eugene Thompson
DINING OUT Build this outdoor table and bench set. TEXT AND PHOTOS BY NEAL BARRETT Photo by Eugene Thompson http://popularmechanics.com/home_improvement/furniture/2001/4/table_and_bench_set/print.phtml
www.cornholesupplies.com
www.cornholesupplies.com How To Build Regulation Cornhole Boards Home of the Original Cornhole Bags and Boards Supply List: 1-4' X 8' Piece of Plywood (pre sanded) 4-2" X 4" X 8' Studs (2 by 4s make sure
a Wall Railing Hanging Get it at the right height and make sure it's fastened to the framing; someone's life may depend on it Handrails and code
Hanging a Wall Railing Get it at the right height and make sure it's fastened to the framing; someone's life may depend on it BY SEBASTIAN EGGERT Handrails and code A graspable handrail is required for
Installing Window Trim and Door Trim
Installing Window Trim and Door Trim Tools and Supplies You'll Need Screws or Finish Nails use screws or nails that are long enough to go through the Ledger and firmly attach to the wall behind it. If
Module 7. Plumber: Sink Installation
Module 7 Plumber: Sink Installation 138 The picture below shows a sample sink installation station. 139 Module 7 Plumber: Sink Installation Module Overview This module will involve the proper setup and
Build a Trade-Show Booth for Under $200!
Build a Trade-Show Booth for Under $200! This corner booth, with a seven foot front and sweeping 4x8 backdrop, assembles in less than 20 minutes and can be built in one weekend. Materials Tools 4 x8 x3/4
VCE VET ENGINEERING STUDIES
Victorian Certificate of Education 2013 SUPERVISOR TO ATTACH PROCESSING LABEL HERE STUDENT NUMBER Letter Figures Words VCE VET ENGINEERING STUDIES Written examination Section Wednesday 20 November 2013
MEZŐKÖVESDI BÚTORIPARI KFT Founded: 1951
Contact person: Laszlo Persze Date: 13.09.21 Side: 1/17 Dear Sir/Madam! Let me thank you for your kind interest in our products. First of all I would like to share some information about our company: The
Panel/Hand Saw Kit Assembly Instructions
Panel/Hand Saw Kit Assembly Instructions PLEASE READ THE FOLLOWING INSTRUCTIONS BEFORE BEGINNING Brief Summary You will be performing the following Tasks: 1. Determining the degree of shaping laying out
Garage Workbench Plans
www.bobsplans.com Garage Workbench Plans Every home woodworker knows the importance of making efficient use of the available space in his or her shop. This workbench is designed to provide the maximum
Barewood Octagon and Elongated Windows Installation Instructions
Step-by-step instructions to a beautiful window. Measuring and Installation of your new window from Century Specialty Windows couldn't be easier with our step-by-step instructions. Quality, function and
ANSI APPROVED 04/11/2014 ANSI APPROVED 08/17/2011. 45 Reaffirmation ANSI APPROVED 02/28/2014. 45 Reaffirmation ANSI APPROVED 05/06/2013
STANDARDS STATUS REPORT As of November 4, 2015 Note: Dates in RED indicate the last action taken; Highlighted Items Indicate New/Open Items; Grey items have been closed Document TC Status Comments ASME
The "DAVID" Steam Engine By Alan Marconett Hobbit Engineering HTTP://WWW.HobbitEngineering.com Alan@HobbitEngineering.
The "DAVID" Steam Engine By Alan Marconett Hobbit Engineering HTTP://WWW.HobbitEngineering.com Alan@HobbitEngineering.com (c) 2/20/03 The David steam engine is a simple oscillating steam engine, many plans
DRAWING INSTRUMENTS AND THEIR USES
Chapter - A DRAWING INSTRUMENTS AND THEIR USES Drawing Instruments are used to prepare neat and accurate Drawings. To a greater extent, the accuracy of the Drawings depend on the quality of instruments
RETROFITTING THE X3 MILLING MACHINE (2)
RETROFITTING THE X3 MILLING MACHINE (2) Dick Stephen continues with the mechanical modifications. Fitting the ball screws The 12mm 2mm pitch supplied by THK ball screws are delivered with the nut fitted
RECLINE IN THE SUMMERTIME Get comfortable on the patio or deck with this sturdy reclining lounge chair
RECLINE IN THE SUMMERTIME Get comfortable on the patio or deck with this sturdy reclining lounge chair As early as the eighth century B.C., the Greeks used a piece of furniture called the kline, for lounging
Total Quantity: IMPORTANT: Plans are to be used with 3 x6 Plexiglass (SKU #298-017).
# Materials: Quantity Each: 4x4x8 3 2x4x8 2 2x8x8 1 4x8x3/4 plywood 1 3 x6 corkboard (can be 18 of the 1 x1 pieces) 1 3 x6 plexiglass 1 8 door casing 3 Primer 1 qt. Total Quantity: TIPS FOR SUCCESSFUL