EDDY FIRE HYDR ANT SETTING THE STANDARD FOR FIRE PROTECTION
|
|
|
- Jasmine Mitchell
- 7 years ago
- Views:
Transcription
1 EDDY FIRE HYDR ANT SETTING THE STANDARD FOR FIRE PROTECTION Time-Tested Performance AWWA C502 Opens Easily and Quickly with Pressure Both Drain and Drainless Features are Available Same Design Since 1875 Clow Valve is a division of McWane, Inc.
2 EDDY FIRE HYDRANT The Eddy hydrant is a classic design built to provide unsurpassed fire protection and an appealing aesthetic. Since 1875, the Eddy hydrant has been reliably serving communities and firemen across the country. The Eddy opens easily and quickly under pressure, ensuring time-tested performance year after year. ENGINEERING FEATURES THREADED NOZZLES Easily replaced locking set screw to hold nozzle in place. O-ring seal. RISING STEM Indicating feature lets you know position of main valve. INDEPENDENT DRAIN Allows plugging of drain without disassembly of hydrant. MAIN VALVE CLOSES AGAINST PRESSURE Eliminates valve seat damage while reducing the potential for water hammer. BREAK FLANGE DESIGN Breakaway parts shear cleanly below the top of the barrel, preventing nozzle section damage or opening of the main valve. MAIN VALVE OPENS WITH PRESSURE Water assists in opening the valve making operation easier, faster and positive. STEM NUT BELOW GROUND LINE Maintains positive shut off of main valve after traffic damage. Does not depend on water pressure. Never needs lubrication. All copper alloy construction.
3 EDDY PARTS ASSEMBLY MAIN VALVE OPENING DIMENSION A B D E F 4 1 / 2 " 6" Inlet 9 1 /4" 9 1 /4" 31 1 /2" 19 3 /4" 2 1 /2" 5 1 / 4 " 6" Inlet 9 1 /4" 9 1 /4" 31 1 /2" 19 3 /4" 2 1 /2" HYDRANT REPAIR ASSEMBLIES Assembly Consisting of Parts A Main Stem AA Main Stem(New Style) A B Hydrant Valve BB Hydrant Valve(New Style) 21A-22A A-28A C Drain Support D Drain Valve E Complete Valve and Stem ASSEMBLIES A & B EE Complete Valve and Stem ASSEMBLIES AA & BB NOTE: Hydrant Valve Assembly O-Ring Style Valve Assembly BB WILL NOT FIT Old Style Lower Stem #29. Old style Packing Valve Assembly B WILL FIT New Style Lower Stem #29A in 4 1 /2", 4 3 /4" and 5 1 /4" Hydrants.
4 F-2640 EDDY FIRE HYDRANT PARTS ASSEMBLY WITH DRAIN ASSEMBLY ITEM NO. DESCRIPTION QTY. MATERIAL 1 Hold Down Bolt 1 Stainless Steel 2 Operating Nut 1 Cast Iron 3 Packing Nut 1 Copper Alloy 4 Packing 1 Rubber 5 Cover 1 Cast Iron 6 Cover Bolts & Nuts 8 Steel, Zinc Plated, Stainless Steel* 7 Swivel Ring 1 Cast Iron 8 Nozzle Section 1 Cast Iron 9 Pumper Nozzle As Ordered Copper Alloy 10 Nozzle Chain Not Shown As Ordered Steel, Zinc Plated 11 Pumper Nozzle Cap As Ordered Cast Iron 12 Pumper Cap Washer As Ordered Rubber 13 Flange Bolts & Nuts 8 Steel, Zinc Plated 14 Flange Gaskets 3 Accopac 15 Nozzle O-Ring 1 Rubber /2" Hose Nozzle As Ordered Copper Alloy /2" Hose Nozzle Cap As Ordered Cast Iron /2" Hose Cap Washer As Ordered Rubber 19 Upper Stem 1 Steel w/copper Alloy Sleeve 20 Standpipe 1 Cast Iron 21A Valve Plate 1 Cast Iron 22A O-Rings 2 Rubber 24 Valve Rubber 1 Rubber 25 Seat Ring 1 Copper Alloy 26 Throttling Ring 1 Copper Alloy 27A Thrust Washer 2 Teflon 28A Snap Ring 1 Stainless Steel 29A Lower Stem 1 Copper Alloy 32 Lock Nut 1 Copper Alloy 33 Drain Spool 1 Copper Alloy 34 Drain Lever 1 Copper Alloy 35 Lever Pin 1 Copper Alloy 36 Clevis & Nut 1 Copper Alloy 37 Drain Support 1 Cast Iron 38 Drain Rod 1 Steel 39 Drain Valve Backer 1 Copper Alloy 40 Drain Valve Rubber 1 Rubber 41 Drain Cup 1 Copper Alloy 42 Retaining Nut 1 Copper Alloy 43 Bottom Bolts & Nuts 4 1 /2"-6 Stainless Steel Extension Kit Contains everything required to extend the stem and barrel. Available in 6" increments. Safety-Flange Repair Kit Includes safety-flange stem coupling and pins, flange gaskets, all bolts, nuts and hardware to repair a hydrant damaged due to a traffic accident. Main Valve Seat Repair Kit Contains valve rubber O-rings washer and snap ring. *Upon Request 5 1 /4"-8 Stainless Steel 44 Bottom Gasket / O-Ring 1 Rubber 45 Bottom 1 Cast Iron 46 Stem Coupling 1 Cast Iron 47 Stem Coupling Pin 2 Stainless Steel 48 Middle Stem 1 Steel RECOMMENDED SPECIFICATIONS 1. Hydrant shall be center stem type and in accordance with AWWA Standard C Hydrant shall be compression type with the main valve opening with the water pressure and have a rising stem to positively indicate open or closed position. 3. Hydrant shall be furnished with frangible break flange and break coupling at the ground line. 4. Copper Alloy stem threads shall be located below the main valve to eliminate necessity of lubrication and in case of damage to hydrant, main valve will remain mechanically closed. 5. Hydrant shall have minimum valve opening of either 4 1/2 or 5 1/4, and shoe inlet of 4 or 6 6. Hydrant shall be designed to permit removal of all working parts without special tools or wrenches. 7. Hydrant shall have automatic drain, independent of main valve, to provide removal or adjustment without shutting off water, and can be cleaned without digging. 8. Hydrant shall be the Eddy Hydrant, manufactured by the Clow Valve Company.
5 F-2641 EDDY NO DRAIN PARTS ASSEMBLY FOR PROTECTION AGAINST CROSS CONNECTION ITEM NO. DESCRIPTION QTY. MATERIAL 1 Hold Down Cap Screw 1 Stainless Steel 2 Operating Nut 1 Cast Iron 3 Packing Nut 1 Copper Alloy 4 Packing 1 Rubber 5 Cover 1 Cast Iron 6 Cover Bolts & Nuts 8 Steel, Zinc Plated, Stainless Steel* 7 Swivel Ring 1 Cast Iron 8 Nozzle Section 1 Cast Iron 9 Pumper Nozzle As Ordered Copper Alloy 10 Nozzle Chain Not Shown As Ordered Steel, Zinc Plated 11 Pumper Nozzle Cap As Ordered Cast Iron 12 Pumper Cap Washer As Ordered Rubber 13 Flange Bolts & Nuts 8 Steel, Zinc Plated 14 Flange Gaskets 3 Accopac 15 Nozzle O-Ring 1 Rubber /2" Hose Nozzle As Ordered Copper Alloy /2" Hose Nozzle Cap As Ordered Cast Iron /2" Hose Cap Washer As Ordered Rubber 19 Upper Stem 1 Steel w/copper Alloy Sleeve 20 Standpipe 1 Cast Iron 21A Valve Plate 1 Cast Iron 22A O-Rings 2 Rubber 24 Valve Rubber 1 Rubber 25 Seat Ring 1 Copper Alloy 26 Throttling Ring 1 Copper Alloy 27A Thrust Washer 2 Teflon 28A Snap Ring 1 Stainless Steel 29A Lower Stem 1 Copper Alloy 43 Bottom Bolts & Nuts 4 1 /2"-6 Stainless Steel 5 1 /4"-8 Steel, Zinc Plated, Stainless Steel 44 Bottom Gasket 1 Accopac 45 Bottom 1 Cast Iron 46 Stem Coupling 1 Cast Iron 47 Stem Coupling Pin 2 Stainless Steel 48 Middle Stem 1 Steel Specify both item number and size of main valve opening when ordering replacement parts. ONLY 8 INTERNAL PARTS Tools Required for Eddy Maintenance and Operation F-2750 Hose and Hydrant Wrench Adjustable Hydrant Wrench with Spanner Fits both Pin type and Rocker type hose couplings. RECOMMENDED SPECIFICATIONS (EDDY NO DRAIN) 1. Hydrant shall be center stem type and in accordance with AWWA Standard C Hydrant shall be compression type with the main valve opening with the water pressure and have a rising stem to positively indicate open or closed position. 3. Hydrant shall be furnished with frangible break flange and break coupling at the ground line. 4. Copper Alloy stem threads shall be located below the main valve to eliminate necessity of lubrication and in case of damage to hydrant, main valve will remain mechanically closed. 5. Hydrant shall have minimum valve opening of either 4 1/2 or 5 1/4, and shoe inlet of 4 or Hydrant shall be designed to permit removal of all working parts without special tools or wrenches. 7. Hydrant shall be without a drain to prevent the possibility of cross connection. 8. Hydrant shall be the Eddy Hydrant, manufactured by the Clow Valve Company. *Upon Request
6 GUARD YOUR WATER SYSTEM FROM ACCIDENT OR ATTACK PATRIOT HYDRANT CHECK VALVE Threats to the water supply can come from either accidental or deliberate acts. Our nation s water superintendents have safeguarded nearly all of the access points to our drinking water. At this time one critical access point is left unprotected the fire hydrant. The Patriot hydrant check valve prevents reverse flow through the fire hydrant, safely protecting our drinking water while providing a full-port unobstructed waterway that allows firefighters access to the water they need when they need it. Unlike locks and special external devices, the Patriot is installed underground, which prevents tampering and allows the hydrant to be operated the moment the firefighters arrive on the scene. The Patriot can be installed on any 6 mechanical joint connection, ensuring compatibility with all hydrant brands providing the flexibility and cost-effectiveness you demand. ALUMINUM BRONZE CLAPPER WITH RESILIENT SEAT
7 RECOMMENDED SPECIFICATIONS 1. The check valve shall be manufactured to all of the testing and performance standards of AWWA C508 and AWWA C550. The Check Valve shall be designed for 250 PSI working pressure and tested to 500 PSI hydrostatic pressure. 2. The check valve shall be a stand alone unit able to be positively restrained to any 6 mechanical joint fire hydrant shoe. 3. The check valve shall be ductile iron ASTM Standard A536 ( ), with NSF approved fusion bonded epoxy coating (interior/exterior). 4. The check valve shall be lead free, with no exposed lead bearing surfaces. 5. The check valve shall have an unobstructed waterway. No reduction of port or redirection of flow will be allowed. 6. The seat shall be retained via a double dove tail O-ring retaining groove design to ensure a positive seal. 7. The check valve shall incorporate integral positive restraint connections that maintain a restrained connection between the fire hydrant and the gate valve. 8. The check valve shall incorporate a stainless steel spring that hastens positive closure and prevents water hammer. 9. All fasteners shall be 304 stainless steel and all interior rubber components shall be EPDM rubber. 10. The check valve shall be produced with no less than 80% post consumer recycled content while being cast, manufactured, assembled and tested in the United States of America.
8 COMMITTED TO ENVIRONMENTAL RESPONSIBILITY CLOW VALVE COMPANY IS COMMITTED TO PROTECTING OUR NATURAL RESOURCES THROUGH ENVIRONMENTALLY RESPONSIBLE MANUFACTURING PRACTICES, INCLUDING THE USE OF 80+% RECYCLED CONTENT IN OUR HYDRANTS AND VALVES. To learn more about our commitment to the environment, call EDDY FIRE HYDRANT WHEN PLACING ORDERS, REQUESTING QUOTES OR SUBMITTALS, PLEASE FURNISH THE FOLLOWING INFORMATION: Quantity of hydrants, accessories and maintenance kits required Size of main valve opening: 4 1/2 or 51/4 Size and number of hose nozzles Size and number of pumper nozzles Hose and pumper nozzle thread specifications Type of inlet connection Depth of trench or bury Direction of opening Size and shape of operating nut, weather shield and cap nuts Color desired Town or municipality ISO South 2nd Street Oskaloosa, Iowa PHONE FAX Clow Valve is a division of McWane, Inc.
American- Darling 5¼" B-84-B-5.
-5 Sealed Lubrication Chamber Seals operating threads from water and debris which greatly reduces routine maintenance. Top Travel Stop Nut Helps prevent stem buckling and damage to bronze components which
OPERATION AND MAINTENANCE MANUAL 5-1/4 B-84-B-5 FIRE HYDRANT
OPERATION AND MAINTENANCE MANUAL 5-1/4 B-84-B-5 FIRE HYDRANT INDEX AMERICAN - DARLING 5-1/4 IN. B-84-B-5 FIRE HYDRANT OPERATION AND MAINTENANCE MANUAL OPERATION AND MAINTENANCE REPAIRS Operation and Maintenance...
Fire Hydrant Troubleshooting
Fire Hydrant Troubleshooting Pulsation or chatter during opening and flow of water from hydrant. Loose condition in stem at lower valve plate nut. Tighten lower valve plate nut and secure with SS lock
Telescoping Post Indicator Wall Post KENNEDY VALVE ISO 9000 ISO 14001
Telescoping Post Indicator Wall Post KENNEDY VALVE ISO 9000 ISO 14001 Telescoping Post Indicator 2945 A 1" SQUARE STEM 9" MAX. = 10" MIN. = 7" FIELD ADJUSTMENT INSTRUCTIONS 1. Remove the top section from
BUTTERFLY VALVES. An industry leader in underground and in-plant applications. STYLE 4500 3 24 STYLE 1450 30 54. Consult factory for sizes 60 120
An industry leader in underground and in-plant applications. BUTTERFLY VALVES STYLE 4500 3 24 STYLE 1450 30 54 Consult factory for sizes 60 120 C504 Class 150B & 250B M&H Valve is a division of McWane,
BUTTERFLY VALVES. An industry leader in underground and in-plant applications. STYLE 4500 3 24 STYLE 1450 30 54. Consult factory for sizes 60 120
An industry leader in underground and in-plant applications. BUTTERFLY VALVES STYLE 4500 3 24 STYLE 1450 30 54 Consult factory for sizes 60 120 C504 Class 150B & 250B M&H Valve is a division of McWane,
Mustang Series PRESSURE REDUCING CONTROL VALVE WITH PRESSURE SUSTAINING FEATURE. M115-2 (Globe) M1115-2 (Angle) Schematic. Standard Components
Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Throttles to maintain minimum upstream pressure PRESSURE REDUCING CONTROL VALVE WITH PRESSURE SUSTAINING FEATURE
PRESSURE REDUCING CONTROL VALVE
Schematics Throttles to reduce high upstream pressure to constant lower downstream pressure Low Flow By-Pass controls at low flows 4 PRESSURE REDUCING CONTROL VALVE with LOW FLOW BY-PASS FEATURE Main Line
SECTION 33 11 00.15 DUCTILE IRON PIPE AND FITTINGS
SECTION 33 11 00.15 DUCTILE IRON PIPE AND FITTINGS PART 1: GENERAL 1.01 COORDINATION OF WORK Connection to existing pipelines may require shutdown of AW facilities. Closely coordinate construction work
Fire Hydrant Operation and Inspection
Fire Hydrant Operation and Inspection Fire Hydrant Operation and Inspection What is in this Lesson? 1. Classification of fire hydrants 2. Nomenclature of major hydrant components 3. Operation of compression
SECTION 15105 DUCTILE IRON PIPE AND FITTINGS
SECTION 15105 DUCTILE IRON PIPE AND FITTINGS PART 1 GENERAL.01 COORDINATION OF WORK Connection to existing pipelines may require shutdown of Owner facilities. Closely coordinate construction work and connections
MODEL 565E - 22 TON AIR/HYDRAULIC AXLE JACK
1 565AKHU HYDRAULIC 1.22 O-RING - 2 REQUIRED UNIT 1.23 O-RING COMPLETE 1.24 TEFLON O-RING 2 REQUIRED 1.3 EXTENSION SCREW 1.3A SPRING PIN 1.4 SPRING SUPPORT 1.5 SCREW BUSHING 1.6 Y SHAPE SEAL RING 1.7 HEAD
STORAGE, INSTALLATION AND MAINTENANCE PROCEDURES
GATE VALVE O.S. & Y 1.0 Periodic Inspections 1.1 The valve stem packing should be inspected at least monthly. If the stem packing shows signs of leakage, simply tighten the adjusting nuts to compress the
INDICATOR POST STYLE 2945 A TELESCOPING BARREL ASSEMBLY UL AND FM APPROVED
INDICATOR POST STYLE 2945 A TELESCOPING BARREL ASSEMBLY UL AND FM APPROVED Available in Sizes B C D E See Page 6 for Dimensions Kennedy Valve/Indicator Posts 17-1 INDICATOR POST STYLE 2945 A TELESCOPING
Constantemp Double Wall Low pressure steam-water Heater F-340LDW,F-640LDW, F-940LDW and F-1240LDW
Installation, Operating and Maintenance Instructions 90/4.5.5 Rev. 0 Constantemp Double Wall Low pressure steam-water Heater F-340LDW,F-640LDW, F-940LDW and F-1240LDW Table of Contents SECTION I... 2 INSTALLATION...
SECTION 33 12 19 FIRE HYDRANTS
SECTION 33 12 19 FIRE HYDRANTS PART 1: GENERAL 1.01 SCOPE A. Fire hydrants. B. Adjustment of fire hydrants and gate valves. 1.02 SUBMITTALS A. Conform to requirements of Section 01 33 00 - Submittals.
A V K I N T E R N A T I O N A L A / S
A V K I N T E R N A T I O N A L A / S Va l v e s & H y d r a n t s f o r F i r e F i g h t i n g U L / U L C L i s t e d a n d F M A p p r o v e d 2 AVK Builds Long Life and Good Economy into your Fire
Section 3510: Reclaimed water Pipes, Valves, and Appurtenances February 11, 2011
STANDARDS AND CONSTRUCTION MANUAL : Reclaimed water Pipes, Valves, and Appurtenances February 11, 2011 PART 1 - GENERAL 1.01 SCOPE OF WORK A. These specifications cover the pipes, fittings, and appurtenances
4. Combi valves. 7. Fire hydrants. 8. Check valves. 9. Air valves
1. General company and product information 2. Flanged gate valves for water 3. Other gate valves for water 4. Combi valves 5. Service connection valves for water 6. Valves and fittings for gas 7. Fire
MÁQUINAS AGRÍCOLAS JACTO S.A. EDITION
AJ English version EDITION - 06/007 CODE - 9790 Parts catalog MÁQUINAS AGRÍCOLAS JACTO S.A. Rua Dr. Luiz Miranda, 650 7580-000 - Pompéia - SP - Brasil Tel.: +55 4 3405-00 - Fax: +55 4 345 306 E-mail: export@jacto.com.br
Stainless Steel Single and Dual Circulation Kits
Instruction Sheet P/N 160780 01 Stainless Steel Single and Dual Circulation Kits Introduction The single and dual high-pressure circulation kits allow you to vary and control the circulation rate of coating
PLUMBING VALVES HOUSTON ORLANDO GREENVILLE 800/392-5066 800/327-3022 800/476-2212 TOTAL MAINTENANCE SOLUTIONS
8-1 BRONZE GATE VALVES 125 psi. SWP 200 psi WOG Threaded ends Non-rising stem Solid wedge disc DOMESTIC IMPORT PART # 40300250 1/4 40300260 40300251 3/8 40300261 40300252 1/2 40300262 40300206 3/4 40300263
Mueller B-101 and A-3 Drilling and Tapping Machines
TM TM Mueller and Drilling and Tapping Machines A guide to selecting Mueller Equipment Mueller TM TM and Drilling and Tapping Machines When it comes to line stopping and drilling and tapping technology
These features have made Lo Torc valves the choice of high pressure plug value users, worldwide:
LO TORC Plug Valve The high value, dependable performance, and low maintenance requirements of Halliburton Lo Torc valves can help reduce overall operating costs and help cut downtime. These features have
B-1145. Faucet Assembly. T&S Brass and Bronze Works, Inc. Travelers Rest, South Carolina 1-800-476-4103
B-1145 Faucet Assembly 1 Screw, Lever Handle 000922-45 2 Index, Button, Blue/Cold 001660-45 Index, Button, Red/Hot 001661-45 3 Handle, Lever 001638-45 4 Asm, Spindle NSF - RH/Cold 009753-25 Asm, Spindle
British Standard Underground Hydrant Range
British Standard Underground Hydrant Range 2 THE NEW AVK BRITISH STANDARD HYDRANT RANGE AVK are the renowned market leading innovators, manufacturers and suppliers of BS 750 fire hydrants into the UK,
James M. Pleasants Company
James M. Pleasants Company SUBMITTAL DATA GAINESVILLE MECHANICAL DECEMBER 20, 2013 PROJECT: GSU: J-183 HUMANITIES LAW BLDG. QUOTE NO:12116 ENGINEER: STEVENS & WILKINSON GASKETED PLATE HEAT EXCHANGER Tag:
RUBBER SLEEVE KNIFE GATE VALVE
RUBBER SLEEVE KNIFE GATE VALVE The model knife gate is a wafer valve designed for a wide range of industrial applications. The double-seated design provides bi-directional shut off. The design of the valve
1/29/2008 DR125 / DR150. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PARTS AND PRICES ARE SUBJECT TO CHANGE 1 of 55
DR125 / DR150 Toll Free: 888-863-2252 PARTS AND PRICES ARE SUBJECT TO CHANGE 1 of 55 CYLINDER HEAD ASSY. 1 125-001 883099006937 CYLINDER HEAD COVER 1 1 2 125-002 883099006944 BOLT M6X28 2 3 3 125-003 883099006951
BERMAD Waterworks. Pressure Relief/Sustaining Valve. 700 Series. Model 730. Features and Benefits. Major Additional Features
Pressure Relief/Sustaining Valve Prioritizing pressure zones Ensuring controlled pipeline fill-up Preventing pipeline emptying Pump overload & cavitation protection Safeguarding pump minimum flow Excessive
Fisher 1052 Size 20 Diaphragm Rotary Actuator with F and G Mounting Adaptation
Instruction Manual 1052 Size 20 Actuator (F & G) Fisher 1052 Size 20 Diaphragm Rotary Actuator with F and G Mounting Adaptation Contents Introduction... 1 Scope of manual... 1 Description... 1 Specifications...
DeZURIK 3-20" BAW AWWA BUTTERFLY VALVES WITH TRANSFER MOLDED SEAT
3-20" BAW AWWA BUTTERFLY VALVES WITH TRANSFER MOLDED SEAT Instruction D10386 August 2013 Instructions These instructions provide installation, operation and maintenance information for BAW Butterfly Valves.
IF IT FLOWS THE BOWIE PUMP CAN PUMP IT
IF IT FLOWS THE BOWIE PUMP CAN PUMP IT Bowie Industries, Inc. Bowie, TX 76230 USA Page 1 Bowie Pumps Manual General Pump Information..Page 2 300 Series Pumps.. Page 5 400 Series Pumps.Page 11 500 Series
World Bridge Replacement Parts for EMD 567 and 645 Diesel Engines
40000927-WB REPAIR KIT, WATER PUMP 40005124-WB MAIN & ROD BEARING KIT, 16 CYLINDER 40005125-WB MAIN & ROD BEARING KIT, 20 CYLINDER 40006129-WB PISTON, 645E HTG AND TIN PLATED 40006130-WB PISTON, 645 E3
Round Housing with Side Ports
Power Steering Steering Control Unit (SCU) Parts and Repair Information 5 Series Steering Control Units 001 Square Housing with Side Ports Round Housing with Side Ports T E L RP Round Housing with End
S GATE KNIFE GATE VALVE WITH PNEUMATIC ACTUATOR
MAIN FEATURES The pneumatic S GATE knife gate valve is intended for the automatic shut off of pipes of the heavy fluids like slurries and powders. The main fields of application are the water treatment,
3", 4", 6" & 8" Model H Series Alarm Check Valve Installation and Maintenance Guide
", ", " & " Model H Series Alarm Check Valve Installation and Maintenance Guide 077 AIRPARK DRIVE STANDISH, MICHIGAN PHONE 99-- 00-2-0 FAX 99--92 www.globesprinkler.com OCTOBER 2 C- BULLETIN A.C.V.I.M.,
Tube Type Oil Skimmer Comparison
Process Overview- Tube Type Oil Skimmers Oil flows down the face of the skimmer and into a sludge pan that is plumbed to a barrel. Model BG01 & BG34 or 6V Oil Skimmer 1.0 or 3/4 Diameter Collector Tube
Hose Clamps & Fittings
All Stainless Steel Marine or Underground Hose Clamps 5/16 HEX HEAD SCREW 60000 SERIES Highly corrosion resistant Use for marine or underground applications Stainless Steel Band, Housing Plated Steel Screw
SECTION 06000 WATER DISTRIBUTION SYSTEMS TABLE OF CONTENTS
SECTION 06000 WATER DISTRIBUTION SYSTEMS TABLE OF CONTENTS 06010 WATER DISTRIBUTION PIPE A. Design B. Materials C. Installation 06020 FIRE PROTECTION A. Fire Hydrants B. Automatic Fire Sprinkler Systems
SECTION 15056 DUCTILE-IRON PIPE AND FITTINGS
SECTION 15056 PART 1 GENERAL 1.01 DESCRIPTION This section includes materials and installation of ductile-iron pipe and fittings for potable and recycled water systems. A written request to use Ductile
08003-1 WATER SERVICE 2
08003_Mar08_2011.pdf Page 1 of 7 INDEX Page 08003-1 WATER SERVICE 2 1.1 Pipe 2 1.1.1 Copper 2 1.1.2 Polyethylene 2 1.2 Valves and Fittings 2 1.2.1 Main Stops 3 1.2.2 Curb Stops 3 1.2.3 Curb Box 3 1.2.4
Experience In Motion. Valtek Spring Cylinder Linear Actuators
Experience In Motion Valtek Spring Cylinder Linear Actuators Valtek Spring Cylinder Linear Actuator Flowserve spring cylinder linear actuators are powerful, compact, high-performance pneumatic actuators
TYPE E Main Valve Sizes 3 /8 through 12
SD 3001F PRINTED IN U.S.A. SD 3001F/0707 A B TYPE E MAIN VALVE C D E TYPE E Main Valve Sizes 3 /8 through 12 The Spence Type E Main Valve is of normally closed, single seat design featuring packless construction,
11-600036D PRO MAC 60 07/72 to 12/76 IPL 89321 Page 1 of 19 Accessories
11-600036D PRO MAC 60 07/72 to 12/76 IPL 89321 Page 1 of 19 Accessories 11-600036D PRO MAC 60 07/72 to 12/76 IPL 89321 Page 2 of 19 Accessories 84453 Kit - Piston tool 69191 Kit - Pressure test adaptor
DR125 and DR150 Hensim Dirt Runner 125cc and 150cc Dirt Bike (VIN PREFIX LLCH or LUAH)
Parts Lists - DR125 and DR150 Hensim Dirt Runner 125cc and 150cc Dirt Bike (VIN PR... Page 1 of 25 Product Information Baja Web > Product Information > Parts Lists > DIRTBIKE > DR125 and DR150 Hensim Dirt
DR90. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PART NUMBERS AND PRICES ARE SUBJECT TO CHANGE 1 of 51
DR90 Toll Free: 888-863-2252 PART NUMBERS AND PRICES ARE SUBJECT TO CHANGE 1 of 51 CYLINDER & CYLINDER HEAD 1 DR90-001 842645048166 CYLINDER 1 1 2 DR90-002 842645048173 GASKET, CYLINDER 1 1 3 DR90-003
Spare Parts Program. Parts, Consumables & Accessories. 800.837.9711 superproductsllc.com
Spare Parts Program Parts, Consumables & Accessories TABLE OF CONTENTS Program Introduction 3 Body 4 5 Boom 5 6 Hydraulic 6 Lights & Accessories 7 Tubes, Nozzles & Hose Fittings 8 11 Vacuum 11 Water 12
FLANGED END BALL VALVE
Specification: FLANGED END BALL VALVE - Chem Oil s two-piece ball valve has been designed to handle extreme service applications with unsurpassed reliability. Valve body machined from solid wrought material
Parts#MB003-003 Reverse Gear MAMBA (Monoblock for Cable operated) For 5 speed Trans., '87 to '06 Big Twin models (except '06 Dyna)
Installation Instructions Reverse Gear MAMBA (Monoblock for Cable operated) Read and become familiar with these installation instructions before start. Two Piece for H-D 5 Speed Trans., Cable operated
DR50 Hensim Dirt Runner 49cc Dirt Bike (VIN PREFIX LLCH or LUAH)
Page 1 of 21 Product Information Baja Web > Product Information > Parts Lists > DIRTBIKE > DR50 Hensim Dirt Runner 49cc Dirt Bike (VIN PREFIX LLCH or LUAH) DR50 Hensim Dirt Runner 49cc Dirt Bike (VIN PREFIX
8D.1 BALL ANGLE METER VALVES - 3/4" & 1" P-24258 B-24258 E-24259 B-24259 B-24266 B-24267
BALL ANGLE METER VALVES - 3/4" & " 8D. B-24258 MUELLER 300 Ball Angle Meter Valve MUELLER 0 Conductive Compression Connection for CTS O.D.* tubing x meter swivel nut** adding -3 suffix to catalog number.
Char-Lynn Hydraulic Motor. Repair Information. 10 000 Series. October, 1997
Char-Lynn Hydraulic Motor October, 1997 Repair Information Geroler Motor Two Speed 001 27 Retainer inside bore of valve plate bearingless motors only 4 15 16 3 6 35 Parts Drawing 25 2 2 1 19 17 36 40 47
Chapter 6 Material Specifications
Chapter 6 Material Specifications Chapter 6 Material Specifications Materials incorporated in the finished work and used during construction shall be according to the standards and specifications specified
OPERATING INSTRUCTIONS AND PARTS LIST FOR U075075 U100058 UNDERGROUND HOSE REELS
OPERATING INSTRUCTIONS AND PARTS LIST FOR U075075 U0005 FORM NO.: 3-00 REV: RAIN BIRD CORPORATION ONE REELCRAFT CENTER COLUMBIA CITY, IN 675 (00) -33 / (60) - FAX: (60) -605 U0005 MODEL NUMBER SIGNIFICANCE
TECHNICAL DATA. Dry 122a. November 12, 2013
Dry 122a 1. PRODUCT DESCRIPTION The Viking is a quick-opening device. When installed with the required external Anti-flood Device, the assembly is designed to increase the operating speed of Viking Model
Installation and Operating Instructions Installation Instructions for SS EPE-316L Series
INSTR3010 0406 Installation and Operating Instructions Installation Instructions for SS EPE-316L Series Congratulations on your purchase of this Aqua-Pure high flow, single housing filtration system. This
TAMPERS. 9949 Tabor Place, Santa Fe Springs, California, CA 90670, U.S.A.
TAMPERS Website: www.apt-tools.com e-mail: info@apt-tools.com TDS-1064 Rev A S TOOL MAINTENANCE & REPAIR INFORMATION FIELD OPERATION: Before use: 1. Check the tamping butt lock screw, it must be tightened
OPERATING and MAINTENANCE MANUAL SERIES 2700A CONTROL VALVE CONTENTS. INTRODUCTION...1 Scope...1 Description...1 Valve Identification...
OPERATING and MAINTENANCE MANUAL SERIES 2700A CONTROL VALVE CONTENTS INTRODUCTION...1 Scope...1 Description...1 Valve Identification...2 1.0 VALVE INSTALLATION...2 2.0 VALVE MAINTENANCE...3 Actuator Disassembly...3
PVM Piston Pumps Service Manual
PVM Piston Pumps Service Manual PVM018/020 PVM045/050 PVM057/063 PVM074/081 PVM098/106 PVM131/141 Table of Contents Service Parts Pump Description... 3 Basic pump Pump Operation Controls Types Part Identification...
Fixtures - Parts - Accessories to shampoo bowls
Page 1??? - For what brand of bowl do you need parts??? Find out by looking on the bottom of the bowl, between the front and strainer, where molded in the bottom is the brand and model number. For example,
G. VULCANIZED SEAT Pressure sensitive seating with full disc overlap provides positive seating at high and low pressures.
A B C D G F E J H I A. RETAINER PLUGS Retain hinge and stop pins while providing compression to stabilization spheres. B. STABILIZATION SPHERES Stabilize hinge and stop pins, preventing vibration and wear.
DYNA RIDER FOOTBOARD KIT
-J0 REV. 0-0-0 DYNA RIDER FOOTBOARD KIT GENERAL Kit Number 000 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English
AIR RELEASE, CLEANOUT, AND SEWER MANHOLES
AIR RELEASE, CLEANOUT, AND SEWER MANHOLES **From Hartford IM BLDG(10) DESCRIPTION. This work shall consist of the construction of air release, cleanout, and sanitary sewer manholes; and the furnishing
V47 Series Temperature Actuated Modulating Water Valves
V47 Series Temperature Actuated Modulating Water Valves Master Catalog 125 Valves, Miscellaneous (Other Than Gas) Section V Product Bulletin V47 Issue Date 0286 Application The V47 modulating valves regulate
REPAIR AND MAINTENANCE MANUAL
REPAIR AND MAINTENANCE MANUAL Professional Pest Control Application Equipment Prime Line Sprayers B&G Equipment Company 135 Region South Drive, Jackson, GA 30233 800.544.8811 Phone 678.688.5601 Fax 678.688.5633
Delta Fire manufacture and supply a comprehensive range of Marine Fire Fighting Equipment.
Marine FIRE FIGHTING Equipment Delta Fire manufacture and supply a comprehensive range of Marine Fire Fighting Equipment. The recent aquisition of the Foundrite range of international couplings, fittings
Trash Pumps Models: 56200, 562000, 56201, 562001, 56300, 563000, 56301, 563001
Trash Pumps Models: 56200, 562000, 56201, 562001, 56300, 563000, 56301, 563001 Specifically designed pumps for heavy duty applications Handles solids with eas and simple to open and clean Standard roll
1/29/2008 DR50. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 45
DR50 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 45 CYLINDER & CYLINDER HEAD Part UPC Number Description Baja Description 1 DR50-001 842645074424 CYLINDER 1 1 2 DR50-002 842645074431
Trunnion-Design Ball Valves
Trunnion-Design Ball Valves 12" 20" (DN 300 500) Series 7150 12" (DN 300) Series 730S 12" 20" (DN 300 500) Series 7300 14" 24" (DN 350 600) Series 9150 14" 24" (DN 350 600) Series 9300 Installation, Maintenance
RING JOINT SYSTEMS 207
RING JOINT SYSTEMS 07 08 Table of Contents Model R-88 Pages 10-11 Model R-88 Large Diameter Page 1 Model RH-1000 1000 PSI Coupling Page 13 Model RX-3000 3000 PSI Coupling Page 1 Model RX-3770 3770 PSI
60.12. Depend-O-Lok FxE Expansion Coupling. System No. Submitted By Spec Sect Para Location Date Approved Date. DEPEND-O-LOK FxE EXPANSION COUPLING
60.1 D-O-L FxE expansion couplings are a bolted, split-sleeve design that provides for expansion and contraction at the coupled joint. These couplings are furnished with restraint rings that, when affixed
K&T Saw Shop 606-678-9623 or 606-561-4983
11-600016C MAC 110 01/77 to 02/83 IPL 95807-R2 Page 1 of 16 Tools & Accessories www.ktoutdoor.com 11-600016C MAC 110 01/77 to 02/83 IPL 95807-R2 Page 2 of 16 Tools & Accessories 95169 Kit - Spark Arrester
Parts Manual. TWIN 2 & 3 Parts & Accessories F210846R01. Your efficiency is our Challenge!
Parts Manual TWIN 2 & 3 Parts & Accessories F210846R01 Your efficiency is our Challenge! All rights reserved. No part of this manual may be copied and/or published by means of printing, photocopying, microfilm
Buy Karcher Parts Online: www.pressureparts.com. Need Technical Help? Call: 1-800-999-2245 email Requests to: sales@pressureparts.
Karcher Model: K 620-M * ( 59556440 ) - Parts Section:1.1 TOP PART Page 1 of 18 1 50346460 1 STRAP 2 63031250 6 SCREW 3 50670230 1 COVER 4 63031940 2 SELF-TAPPING SCREW 5 50309650 1 COVER 6 50635710 1
FITTINGS AND VALVES. Ductile Cast Iron Hydrants
FITTINGS AND VALVES Ductile Cast Iron Hydrants Düker Hydrants Important Elements of a Modern Public Water Supply Ductile cast iron hydrants Düker underground and pillar hydrants Hydrants are an important
BSA Goldstar Parts - Price List April 2016. 65-1137 Exhaust Lifter Cable 15.00. 65-1163 Exhaust Lifter Cable Holder S/S 9.00
Rocker Boxes 65-1137 Exhaust Lifter Cable 15.00 65-1163 Exhaust Lifter Cable Holder S/S 9.00 2-443 Exhaust Lifter Cable Holder Nut S/S 0.50 65-401 Exhaust Lifter Spindle Felt 2.00 65-387 Exhaust Lifter
BOWIE PUMPS OPERATION - MAINTENANCE
BOWIE PUMPS OPERATION - MAINTENANCE PUMPING PRINCIPLE: The meshing owieeof the gears cause a slight depression, with the resulting enmeshing of the gears causing a vacuum drawing the fluid being pumped
BERMAD Waterworks. Pressure Reducing Valve. 700 Series. Model 720. Features and Benefits. Major Additional Features
Pressure Reducing Valve Flow and leakage reduction Cavitation damage protection Throttling noise reduction Burst protection System maintenance savings The Pressure Reducing Valve is a hydraulically operated,
DR90. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PART NUMBERS AND PRICES ARE SUBJECT TO CHANGE 1 of 51
DR90 Toll Free: 888-863-2252 PART NUMBERS AND PRICES ARE SUBJECT TO CHANGE 1 of 51 CYLINDER & CYLINDER HEAD Part UPC Number Description Baja Description 1 DR90-001 842645048166 CYLINDER 1 1 2 DR90-002
Jay R. Smith Mfg. Co.
Jay R. Smith Mfg. Co. Automatic Backwater Valve SMITH CUSTOMER DRIVEN FLOOD-GATE FEATURES Index Page Flood-Gate Features and Applications 2 How Flood-Gate Works 3 Flood-Gate Operation & Approvals 4 Valve
PET. Illustration 001-00. Pos Part Number Description Remark Qty Model. - 356 72 106 jack 1. - 356 72 108 operating rod 1. - 356 72 103 tool bag 1
Model 959 0 0 00-00 7 6:56.0.00 tool and accessories tool - 7 06 jack - 7 0 operating rod - 7 03 tool bag - 7 0 spark plug wrench - 0 A ring wrench 36 MM - - tyre pressure gauge L 709 0-999 57 05 0 rim
Price Book - Section 20 Miscellaneous
Effective Date Price Book - Central - 4" Dry Pipe Valve Model AF or AG (2002) (each) Valve Cover 40002000 $564.50 Cover Bolts (Purchase 6 Units Each) 60003000 $15.50 Cover Gasket 40004000 $139.00 Clapper
RIVET BUSTERS. 9949 Tabor Place, Santa Fe Springs, California, CA 90670, U.S.A.
S Website: www.apt-tools.com e-mail: info@apt-tools.com TDS-1038 Rev A S TOOL MAINTENANCE & REPAIR INFORMATION FIELD OPERATION: Before use: 1. Fill and attach an in-line oiler to the air tool. Use air
RMF Engineering 23 05 23
PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.
Mechanical Joint Restraints
-15 PVC Pipe Restrainer The PVC mechanical joint restrainer eliminates the need for thrust blocking, tie rodding, or harnessing mechanical joint fittings when they are used with PVC pipe. The key to the
DARTMOUTH COLLEGE DESIGN January 3, 2012 & CONSTRUCTION GUIDELINES
SECTION 15062 STEAM AND CONDENSATE PIPING PART 1 DESIGN DIRECTIVES 1.1 QUALITY ASSURANCE A. Comply with the provisions of the following: 1.2 DESIGN CRITERIA 1. ASME B 31.9 Building Services Piping : for
CHIPPING HAMMERS. 9949 Tabor Place, Santa Fe Springs, California, CA 90670, U.S.A.
CHIPG HAMMERS Website: www.apt-tools.com e-mail: info@apt-tools.com TDS-1056 Rev A CHIPG HAMMERS TOOL MAINTENANCE & REPAIR INFORMATION FIELD OPERATION: Before use: 1. On 650 Series tools, tighten the handle
Ductile Iron Pipe Couplings
J-9 Pipe 1 2 Straight and Transition Ductile offer an easy and economical way of joining whether the is of the same nominal and/or type or different at each coupling. couplings will handle most of your
Volkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 17 Engine-Lubrication system (Page GR-17)
17 Engine-Lubrication system (Page GR-17) Lubrication system components, removing and installing Oil pan, removing and installing Oil pressure and oil pressure switch, checking Dynamic oil pressure warning
WIRE ROPE CUTTERS. Designed for new and unused wire rope. Since 1928
WIRE ROPE CUTTERS Designed for new and unused wire rope Since 1928 IMPACT 101 104 106 108 103 105 107 109 Model 1 (light duty): Model 1 3 /4 capacity 101 Cutter complete 8 lbs. 102 Casting base 4 lbs.
Table of Contents. Overview 1. Pump Disassembly 2. Control Disassembly / Reassembly 7. Pump Reassembly 13. Adjustment Procedures DR Control 19
Table of Contents Overview 1 Pump Disassembly 2 Control Disassembly / Reassembly 7 Pump Reassembly 13 Adjustment Procedures DR Control 19 Adjustment Procedures DRG Control 20 Adjustment Procedures DFR
K&T Saw Shop 606-678-9623 or 606-561-4983
12-600072F PRO MAC 850 SUPER CHAIN SAW 05/92 to Current IPL 215710-R1 Page 1 of 16 Accessories www.ktoutdoor.com 12-600072F PRO MAC 850 SUPER CHAIN SAW 05/92 to Current IPL 215710-R1 Page 2 of 16 Accessories
INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS PARTS LIST
12501 Telecom Drive, Tampa Florida 33637 INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS PARTS LIST 90/4.5.1 Rev.1 CONSTANTEMP LOW PRESSURE STEAM-WATER HEATERS Models E-1500L, E-1520L, E-300L, E-320L,
4 of 303 10/7/2014 12:51 PM
National Fire Protection Association Report http://submittals.nfpa.org/terraviewweb/contentfetcher?commentpara... 4 of 303 10/7/2014 12:51 PM Second Revision No. 167-NFPA 13-2014 [ Section No. 3.8.1.3
Innovative Products For Unique Applications. A Tradition of Excellence. Creative Engineering for Fluid Systems. Earthquake Proof Valves
A Tradition of Excellence With the development of the first rubber seated butterfly valve more than 70 years ago, the Henry Pratt Company became a trusted name in the flow control industry, setting the
BERMAD Waterworks. Quick Active Check Valve. 700 Series. Model 740Q. Features and Benefits. Major Additional Features
Booster Pump Control Valve Quick Active Check Valve Isolates system from the effects of pump starts and stops for: Solitary single speed pumps Battery of single speed pumps (add & switch) Battery of variable
Owner s Manual. Models: 2S5P & 3S5P OPERATION AND MAINTENANCE OF SELF-PRIMING CENTRIFUGAL TRASH PUMPS PEDESTAL DRIVE
Owner s Manual Models: 2S5P & 3S5P OPERATION AND MAINTENANCE OF SELF-PRIMING CENTRIFUGAL TRASH PUMPS PEDESTAL DRIVE WARNING!! Installation & Operating Instructions Self-Priming Centrifugal Pump DO NOT
HYDRAULIC TABLE CART 500-LB.
HYDRAULIC TABLE CART 500-LB. OWNER S MANUAL WARNING: Read carefully and understand all MACHINE ADJUSTMENT AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic
I. Introduction. 10 minutes
I. Introduction 10 minutes Introduction (1 of 2) An uninterrupted water supply is: The primary weapon for extinguishment Essential for fire fighter safety Ensuring a dependable water supply is a critical