Monarch Hydraulics, Inc. Monarch M-Series A.C. Hydraulic Power Systems
|
|
|
- Dana Parker
- 7 years ago
- Views:
Transcription
1 Monarch Hydraulics, Inc. Monarch M-Series A.C. Hydraulic Power Systems Table of Contents Features and Options How to Use This Product Guide M-400 Series Power System Selection Guide M-400 Series Pump/Motor Performance Data M-400 Series Motor Information Dimensional Information for Standard M-400 Motors With Flexible Couplings Reservoirs for M-400 Units Reservoirs for Mini Units Valves for M-400 Series Units M-400 Series Accessories Model Descriptions and Ordering Guide Model M-455 Mini System Model M Model M-454 Mini System Model M Model M Model M Model M Model M-459 Mini System Model M-458 Mini System Model M Model M Model M Model M-452 Mini System Model M-453 Mini System Model M Model M Model M Model M-428-P Model M-466 Mini System Model M-457 Mini System
2 Monarch M-Series A.C. Hydraulic Power Systems Features and Options STANDARD M-400 SERIES FEATURES FLEXIBLE COUPLING EXTENDS PUMP LIFE, ELIMINATES MISALIGNMENT ACCEPTS STANDARD NEMA 56C THROUGH 184C MOTORS ALL STEEL GEARS HARDCOATED PUMP END PLATES FOR UNMATCHED DURABILITY IN DEMANDING ENVIRONMENTS AND SEVERE DUTY APPLICATIONS EXTERNALLY ADJUSTABLE RELIEF VALVE WITH LOCK NUT 1 YEAR LIMITED WARRANTY ON SYSTEM 2 YEAR LIMITED WARRANTY ON PUMP MONARCH'S PERSONAL CUSTOMER SERVICE 24 HOUR SHIPMENT ON MOST PARTS ORDERS OVER ONE MILLION M PUMPS SOLD WORLDWIDE DISTRIBUTOR NETWORK OPTIONS PRESSURE GAUGES SAE PORTS ON MOST MODELS COMPLETE SELECTION OF NFPA DO3 CONTROL VALVES AND AUXILIARY VALVES CROSS PORT RELIEF PRESSURE REDUCING SINGLE AND DOUBLE FLOW CONTROL DIRECT AND PILOT OPERATED CHECK SEQUENCE COUNTER BALANCE RELIEF PRESSURE SWITCHES ACCUMULATORS WATER/OIL HEAT EXCHANGERS FLOAT SWITCHES RESERVOIRS 56 FRAME AIR MOTORS EXPLOSION PROOF, 50 HERTZ, CHEMICAL DUTY, DUAL FREQUENCY, METRIC FRAME, HIGH TORQUE AND SPECIAL DUTY ELECTRIC MOTORS GASOLINE AND DIESEL ENGINES CLOSE COUPLED MOTORS AVAILABLE ON MANY SYSTEMS 2.0
3 Monarch Hydraulics, Inc. How to Use This Product Guide I. Select the Circuit that will satisfy your design objectives (refer to page 4.0). Contact the Monarch Factory or your Distributor if you require assistance. II. III. IV. Select the Model that will provide the desired performance (Flow/Pressure) and Valve Activation (Solenoid or Manual) listed in the Power System Selection Guide (refer to page 4.0). Follow the How To Order Your M-4XX Power System provided after each Model description. Only the recommended combinations are listed for the particular system. Custom configurations are available and should be discussed with the Monarch Factory or your Distributor. The operating and design characteristics for all of the basic components are listed on pages of this guide. Select Pump and HP on Page 5.0, 8.0, or 9.0. Select Motor on Pages 6.0, 8.0 or 9.0. Select Reservoir on Page 10.0 or Select Valve(s) on Pages Select Accessories on Page EXAMPLE: V. Order Your Hydraulic Power System As Follows: Select Circuit: Pump/Motor/Reservoir. Page 4.0. Select Model: M-404. Page 4.0. Performance Required: PSI. Reference Page 5.0. Select Pump: 51 ( RPM). Page 5.0 Select Motor: (1-1/2 HP, 1725 RPM). Page 6.0. Select Reservoir: 06073, Page Accessories: None Model Code: M Horizontal Mounting VI. VII. VIII. IX. Nominal Dimensions are shown for all basic components. Dimensions may be found for your particular system by deleting the component shown on the unit drawing and adding the dimension for the same item you have selected. Note: Motor dimensions may vary according to the manufacturer and should be confirmed by the Monarch Factory or your Distributor. When selecting Motor, choose the HP required or the next highest HP available. When selecting a Reservoir, consideration should be given to dissipating heat, separating air from the oil, and settling out contamination in the oil. The traditional rule of thumb is that the reservoir should be 2-3 times larger than the pump output per minute. There must always be a reserve of oil in the reservoir when all cylinders are fully extended. Contact the Monarch Factory or your Distributor for proper reservoir sizing for your application. All system wiring should be completed by a certified electrician according to local codes. 3.0
4 Monarch M-Series A.C. Hydraulic Power Systems M-400 Series Power System Selection Guide CIRCUIT DESCRIPTION MODEL PAGE PUMP + MOTOR M-455 MINI M OPERATES SINGLE ACTING CYLINDER PUMP + MOTOR + RESERVOIR M-454 MINI M-404 PUMP + MOTOR + RESERVOIR + MANUAL VALVE M-413 M-401 M-415 PUMP + MOTOR + RESERVOIR + SOLENOID VALVE OPERATES DOUBLE ACTING CYLINDER M-459 MINI M-458 M-419 M PUMP + MOTOR + RESERVOIR + MANUAL VALVE M PUMP + MOTOR + RESERVOIR + SOLENOID VALVE OPERATES 2 DOUBLE ACTING CYLINDERS M-452 MINI M-453 M-406 M-405 PUMP + MOTOR + RESERVOIR + SOLENOID VALVES M-428 M-428-P INDEPENDENT OPERATION OF 2 SINGLE ACTING CYLINDERS OR MASTER/SLAVE PUMP + MOTOR + RESERVOIR + SOLENOID VALVES M-466 MINI M-457 MINI
5 Monarch Hydraulics, Inc. M-400 Series Pump/Motor Performance Data DISPLACEMENT INPUT HP REQUIRED AT PRESSURE (PSI) PUMP CODE In 3 /Rev (Cm 3 /Rev) RPM GPM (.524) (.934) (1.26) (1.66) (2.13) (2.31) (3.23) (4.11) Bold = Intermittent Service Only. Contact the Monarch Factory or your Distributor for operating limits. The above pumps tested using Mobil DTE 24 at 100 F 165 SUS, 95 Viscosity. Note: kw = HP x Recommended Operating Conditions for M-400 Series Pumps: Oil Temperature Range: 10 F to 170 F (-25 C to 77 C) Operating Temperature: 50 F to 130 F (10 C to 54 C) Oil Viscosity: Optimum 100 to 350 SUS (Cst =.22 x SUS - 135/SUS) Minimum 100 SUS Maximum Start Up 4000 SUS Recommended Filtration: 10 micron nominal or better Recommended Fluid for indoor use: Mobil DTE 24 or equal Recommended Fluid for outdoor use: Mobil DTE 13 or equal Contact factory for use with non-petroleum based fluids and availability of special seals. STANDARD PUMP FEATURES: Fixed Displacement, External Tooth, All Steel Cut Gears Hardcoat Processed Internal Pump Surfaces Extend Service Life Extremely Tolerant of Fluid Contaminants and Resistant to Galling Caused by Low Viscosity Start-up Wide Temperature and Viscosity Operation Cost Effective Bearing on Drive Shaft Minimizes Axial Thrust Effects 100% Tested for Volumetric Efficiency and Pressure Over One Million M Pumps Sold 5.0
6 Monarch M-Series A.C. Hydraulic Power Systems M-400 Series Motor Information MONARCH PART NUMBER HP RPM VOLTAGE PHASE FRAME ENCLOSURE / /230/ C TEFC / /230/ C TEFC / /460/ C TEFC /230/ C TEFC /460/ C TEFC /230/ C TEFC /460/ C TEFC / /230/ C TEFC / /460/ C TEFC / /230/ C TEFC / /460/ C TEFC / /200/60 100/200/ C TENV 15 MIN 1.5 HP /230/ C TENV 15 MIN 2.0 HP 5 MIN 2.8 HP /230/ C TEFC /460/ C TEFC /230/ C TEFC /460/ C TEFC /230/ C TEFC /460/ C TEFC Monarch Supplied 56C Motors have the standard length NEMA shaft shortened by 1-3/16". All other frame size motors and all special ordered units are supplied with NEMA standard length drive shafts when possible. The above motors may be specified with standard NEMA 56C length drive shafts. Motors commonly available for use with M-400 units include: Explosion Proof Dual Frequency (50/60 Hz) Intermittent Duty - Custom Designed Washdown Duty 575V AC Open Drip Proof Totally Enclosed Non-Ventilated Custom Designed Motors for Applications 6.0
7 Monarch Hydraulics, Inc. Dimensional Information for Standard M-400 Motors With Flexible Couplings Motor Number is a 2 HP, 3450 RPM, 115/230 V AC, 60 Hz, 1 Phase, NEMA 56C TEFC and is shown as a general reference. Dimensions will vary according to motor output and manufacturer. Contact the Monarch Factory for more information. Monarch standard adapters 01605, 01606, and require the NEMA motor shaft be shortened by 1-3/16". Adapters 01615, 01616, or should be specified when a standard NEMA motor shaft is required. 15/16" 5/8" Ø 2" 8-11/16" 1-5/8" 6-13/16" 10-11/16" 8-1/4" SIDE VIEW END VIEW 7.0
8 Monarch M-Series A.C. Hydraulic Power Systems II. Close Coupled Motors For M-400 Units The following direct drive (partial) motors are supplied with an adapter for mounting the pump base directly to the motor. The and/or extended pump/motor adapter and flexible coupling is not required. The close coupled motors may be used on Models: M-401, M-404, M-410, M-415, M-419, M-426, M-428 and M-428-P. MONARCH PART NUMBER HP DUTY RPM VOLTAGE PHASE FRAME ENCLOSURE /2 15 MINUTE / TENV /4 3 MINUTE / TENV MINUTE / TENV MINUTE / TENV MINUTE TENV MINUTE / TENV Dimensional Information for Close Coupled Motors Shown W/Optional Thermal Switch 6-1/4" Shown W/Optional Base "L" = 7-1/2" "L" = 8-1/16" "L" SIDE VIEW 2-5/8" 1-11/16" END VIEW 4-11/16" 1-9/16" Single Phase Only 42 FRAME MOTOR DIMENSIONS Shown W/Optional Thermal Switch 5-7/8" 3" 8-7/16" 1-5/8" 5-11/16" 2-1/4" SIDE VIEW 48 FRAME MOTOR DIMENSIONS END VIEW Single Phase Only 8.0
9 Monarch Hydraulics, Inc. 1-1/2" 3-1/2" 8-7/8" 6-1/2" 2-1/4" SIDE VIEW END VIEW 56 FRAME MOTOR AND ADAPTER III. Close Coupled Motors for Monarch M-450 Mini Units The V AC, PSC 1 Phase, 60 Hz Motor is standard on all Mini Units. The motor includes a thermal overload with automatic reset. A capacitor is required. The µf 330V AC Capacitor is available as optional equipment. Note: Other Voltages, Enclosures, and Capacitors are available. 5-13/16" 3-8/25" SIDE VIEW END VIEW MINI AC MOTOR DISPLACEMENT Maximum Run Time in Minutes at Maximum Pressure (PSI) with Capacitor PUMP CODE In 3 /Rev (Cm 3 /Rev) RPM GPM (.524) (.934) (1.26) Longer run time available with decrease in pressure. Contact Factory. 9.0
10 Monarch M-Series A.C. Hydraulic Power Systems Reservoirs for M-400 Units Part No Part No Horizontal Mounting Length Vertical Mounting Length Useable Capacity In Liter Useable Capacity In Liter TYP TYP. 3/8" NPT Part No Length Useable Capacity Horizontal Vertical In 3 Liter In 3 Liter TYP TYP /8" NPT Part No Length 10" Sq. x 10"H 12" Sq. X 10"H 14" Sq. X 10"H Useable Capacity In Liter /4" NPT
11 Monarch Hydraulics, Inc. Reservoirs for Mini Units Part No Length Useable Capacity Horizontal Vertical In 3 Liter In 3 Liter Part No Length Useable Capacity Horizontal Vertical In 3 Liter In 3 Liter /8" NPT /8" NPT /8" NPT 1/8" NPT FILL LINE
12 Monarch M-Series A.C. Hydraulic Power Systems Valves for M-400 Series Units I. NPFA DO3 Directional and Auxiliary Control Valves. Solenoid directional and auxiliary controls are typically added to the M-405, M-428, and M-429. Please refer to the Monarch Directional Control Valve brochure for additional information and selection. PART NUMBER SCHEMATIC DESCRIPTION b A B P T a 4-Way/3-Position. Solenoid Operated. Tandem Center. 110V AC b A B P T a 4-Way/3-Position. Solenoid Operated. Open Center. 110V AC b A B P T a 4-Way/3-Position. Solenoid Operated. Closed Center. 110V AC b A B P T a 4-Way/3-Position, P Blocked. A and B to T. "Motor Spool". 110V AC b A P B T AB PT B1 A1 4-Way/2-Position. P to A. Spring Offset. 110V AC. 4-Way/2-Position. Dual Detent. 110V AC. Dual Pilot Operated Check. A and B Port P T B A P T A B P T A B P T A B Flow Control. Dual Meter Out. A and B Port. Cross Port Relief. A and B Ports. Adjustable. Dual Relief. A and B Ports to T. Adjustable. Consult your local Monarch distributor or the factory about special requirements for explosion proof, shockless (soft shift) and other function and spool configurations not shown here. 12 and 14 VDC, 24 VAC and other voltages are available. Functional symbols related to solenoid identity "A" or "B" according to NFPA/ ANSI standards, i.e., energizing solenoid "A" gives flow P to A, solenoid "B" gives flow P to B (As Applicable). 12.0
13 Monarch Hydraulics, Inc. II. Cartridge Valves Solenoid operated cartridge valves are used in the M-403, M-419, and M-452 units. PART NUMBER SCHEMATIC DESCRIPTION IN OUT IN OUT IN OUT IN OUT 2-Way/2-Position Normally Closed. Modified Cavity #8. 110V AC. Conduit Connector. 2-Way/2-Position Normally Closed. Modified Cavity #8. Manual Operation. Pull to Open. Spring Close. 2-Way/2-Position Normally Closed. Modified. Cavity #8. Manual Overide. 110V AC. Conduit Connector. 2-Way/2-Position Normally Open. Modified Cavity #8. 110V AC. Conduit Connector. 2-Way/2-Position Normally Closed. Modified Cavity #8. 220V AC. DIN Connection. 4-Way/2-Position. Common Cavity #8. 110V AC. Conduit Connector. Consult Factory or your Monarch Distributor about additional valve options. III. Manual Valves Manually Operated Directional Control Valves are used on Models M-401 and M-410. PART NUMBER SCHEMATIC DESCRIPTION A B P T CYL 4-Way/3-Position. Closed Center. Manually Operated. 3-Way/3-Position. Cylinder Port Checked A B P T A B P T A B P T 4-Way/3-Position. Open Center. Manually Operated. 4-Way/3-Position. Tandem Center. Manually Operated. 4-Way/3-Position. Tandem Center. NFPA DO
14 Monarch M-Series A.C. Hydraulic Power Systems M-400 Series Accessories PART NUMBER DESCRIPTION Sight Level/Temperature Gauge Reservoir Breather, Flush Mount,.375" NPT. Cross Scored Reservoir Breather..375" NPT Reservoir Breather..750" NPT Sight Glass. 3/4" NPT Pressure Gauge, Liquid Filled. 1/4" NPT PSI Pressure Gauge, Liquid Filled. 1/4" NPT PSI Pressure Gauge, Liquid Filled. 1/4" NPT PSI Gauge Shutoff. 1/4" NPT Flow Control, Adjustable. 1/4" NPT Float Switch, Electrical N.O. or N.C Filter, Return Line. 15 GPM. 10 Micron Nominal Filter, Return Line. 5 GPM. 10 Micron Nominal Filler/Breather, Chrome Plated. Basket Strainer. Other Available Options and Accessories Include: Accumulators Air Motors Heat Exchangers Temperature Switches Pressure Switches Motor Controls Multi-Function Valve Controls - Monoblock and Sectional 14.0
15 Monarch Hydraulics, Inc. Model Descriptions and Ordering Guide 15.0
16 Monarch M-Series A.C. Hydraulic Power Systems MODEL M-455 Mini System Description: Pump/Motor Unit Check Valve Externally Adjustable Relief Valve.375 Inch NPT Suction 7/16-20 SAE O-Ring Outlet Port M M-455-S HYDRAULIC SCHEMATIC Mounting Holes Relief Valve Suction 4-1/4" 4" 5-13/16" 2-1/4" 1-15/16" 3-1/2" 10" SIDE VIEW Spacer Req'd. Optional Outlet Mounting Holes Outlet 3-13/16" END VIEW 16.0
17 Monarch Hydraulics, Inc. How to Order Your M-455 Mini System Select from the following options. Comprehensive performance data may be found on the page referenced below each selection category. MODEL M-455- PUMP MOTOR CAPACITOR ACCESSORIES Ref. Page 9.0 Ref. Page 9.0 Ref. Page 9.0 Ref. Page
18 Monarch M-Series A.C. Hydraulic Power Systems MODEL M-426 Description: Pump/Motor Unit Check Valve Externally Adjustable Relief Valve.375 Inch NPT Suction.375 Inch NPT Outlet.125 Inch NPT Relief Valve Return Port OUTLET PORT 3/8 NPTF M HYDRAULIC M-426-S SCHEMATIC Relief Valve Return Outlet Relief Valve 2" Suction 8-11/16" 6-11/16" "L" "A" 1-3/8" 6-13/16" 1-15/16" 1-5/8" 8-1/8" SIDE VIEW END VIEW "L" dimension shown for motor is 10-11/16" "A" dimension for standard adapter is 2-5/32" "A" dimension for optional adapter is 3-11/32" Dimensions will vary according to motor output and manufacturer 18.0
19 Monarch Hydraulics, Inc. How to Order Your M-426 Power System Select from the following options. Comprehensive performance data may be found on the page referenced below each selection category. MODEL M-426- PUMP MOTOR ACCESSORIES Ref. Page 5.0 Ref. Page 6.0 Ref. Page CLOSE COUPLED Ref. Page 8.0 M-426-C
20 Monarch M-Series A.C. Hydraulic Power Systems MODEL M-454 Mini System Description: Pump/Motor/Reservoir Unit Externally Adjustable Relief Valve 7/16-20 SAE O-Ring Outlet Port, 3/8" NPT Return Horizontal Mounting Standard Vertical Mounting (Motor Up) Optional M M-454-S HYDRAULIC SCHEMATIC Mounting Holes Relief Valve Return Port FILL LINE MONARCH 4-1/4" 4" Spacer Req'd. Optional Outlet Mounting Holes Outlet 5-13/16" 2-1/4" 6-15/32" 3-1/2" 14-17/32" 3-13/16" SIDE VIEW END VIEW M
21 Monarch Hydraulics, Inc. How to Order Your M-454 Mini System Select from the following options. Comprehensive performance data may be found on the page referenced below each selection category. MODEL M-454- PUMP MOTOR CAPACITOR RESERVOIR ACCESSORIES Ref. Page 9.0 Ref. Page 9.0 Ref. Page 9.0 Ref. Page 11.0 Ref. Page Horizontal Vertical 21.0
22 Monarch M-Series A.C. Hydraulic Power Systems MODEL M-404 Description: Pump/Motor/Reservoir Unit Check Valve Externally Adjustable Relief Valve.375 Inch NPT Outlet and Return Horizontal Mounting Standard Vertical Mounting (Motor Up) Optional OUTLET PORT 3/8 NPT M HYDRAULIC M-404-S SCHEMATIC Outlet Return Relief Valve 2" 8" 8-11/16" 1-3/8" "L" "A" 24-1/2" 1" 9" 1-5/8" 6-13/16" 8-1/8" SIDE VIEW END VIEW "L" dimension shown for motor is 10-11/16" "A" dimension for standard adapter is 2-5/32" "A" dimension for optional adapter is 3-11/32" Dimensions will vary according to motor output and manufacturer 22.0
23 Monarch Hydraulics, Inc. How to Order Your M-404 Power System Select from the following options. Comprehensive information may be found on the page referenced below each selection category. MODEL M-404- PUMP MOTOR RESERVOIR ACCESSORIES Ref. Page 5.0 Ref. Page 6.0 Ref. Page 10.0 Ref. Page CLOSE COUPLED Ref. Page 8.0 M-404-C Horizontal Vertical
24 Monarch M-Series A.C. Hydraulic Power Systems MODEL M-413 Description: OUTLET PORT 3/8 NPTF Pump/Motor/Reservoir/Valve Manually Operated 2-Way/2-Position Normally Closed Valve Externally Adjustable Relief Valve.375 Inch NPT Outlet Horizontal Mounting Standard Vertical Mounting (Motor Up) Optional M HYDRAULIC M-413-S SCHEMATIC Outlet 3-5/8" Relief Valve 11-5/8" 8-11/16" 8" 8-1/8" 1-3/8" "L" "A" 24-1/2" 1" 9" 1-5/8" 6-13/16" 8-1/8" SIDE VIEW END VIEW "L" dimension shown for motor is 10-11/16" "A" dimension for standard adapter is 2-5/32" "A" dimension for optional adapter is 3-11/32" Dimensions will vary according to motor output and manufacturer 24.0
25 Monarch Hydraulics, Inc. How to Order Your M-413 Power System Select from the following options. Comprehensive information may be found on the page referenced below each selection category. MODEL M-413- PUMP MOTOR RESERVOIR ACCESSORIES Ref. Page 5.0 Ref. Page 6.0 Ref. Page 10.0 Ref. Page Horizontal Vertical
26 Monarch M-Series A.C. Hydraulic Power Systems MODEL M-401 Description: Pump/Motor/Valve/Reservoir Unit 3-Way Manually Operated Valve Externally Adjustable Relief Valve.250 Inch NPT Outlet Horizontal Mounting Standard Vertical Mounting (Motor Up) Optional OUTLET PORT 1/4 NPT M HYDRAULIC M-401-S SCHEMATIC Outlet Relief Valve 14-1/4" 11" 8" 1-3/8" "L" "A" 24-1/2" 1" 9" 1-5/8" 6-13/16" 8-1/8" SIDE VIEW END VIEW "L" dimension shown for motor is 10-11/16" "A" dimension for standard adapter is 2-5/32" "A" dimension for optional adapter is 3-11/32" Dimensions will vary according to motor output and manufacturer 26.0
27 Monarch Hydraulics, Inc. How to Order Your M-401 Power System Select from the following options. Comprehensive information may be found on the page referenced below each selection category. MODEL M-401- PUMP MOTOR RESERVOIR ACCESSORIES Ref. Page 5.0 Ref. Page 6.0 Ref. Page 10.0 Ref. Page Horizontal Vertical CLOSE COUPLED Ref. Page 8.0 M-401-C
28 Monarch M-Series A.C. Hydraulic Power Systems MODEL M-415 Description: 1/4 NPTF Pump/Motor/Reservoir Unit Integral Shuttle Valve Externally Adjustable Relief Valve.250 Inch NPT Outlet Horizontal Mounting Standard Vertical Mounting (Motor Up) Optional M HYDRAULIC SCHEMATIC M-415 Outlet Relief Valve 2" 8" 8-11/16" 1-3/8" "L" "A" 24-1/2" 1" 9" 1-5/8" 6-13/16" 8-1/8" SIDE VIEW END VIEW "L" dimension shown for motor is 10-11/16" "A" dimension for standard adapter is 2-5/32" "A" dimension for optional adapter is 3-11/32" Dimensions will vary according to motor output and manufacturer 28.0
29 Monarch Hydraulics, Inc. How to Order Your M-415 Power System Select from the following options. Comprehensive information may be found on the page referenced below each selection category. MODEL M-415- PUMP MOTOR RESERVOIR ACCESSORIES Ref. Page 5.0 Ref. Page 6.0 Ref. Page 10.0 Ref. Page Horizontal Vertical CLOSE COUPLED Ref. Page 8.0 M-415-C
30 Monarch M-Series A.C. Hydraulic Power Systems MODEL M-459 Mini System Description: Pump/Motor/Valve/Reservoir Unit Check Valve Externally Adjustable Relief Valve 2-Way/2-Position Normally Closed Solenoid Operated Lowering Valve Outlet Port Options: Check Valve Port 7/16-20 SAE O-Ring or Face Port: 7/16-20 SAE O-Ring Horizontal Mounting Standard Vertical Mounting (Motor Up) Optional M HYDRAULIC M-459-S SCHEMATIC Lowering Valve Mounting Holes Relief Valve FILL LINE MONARCH 5-1/4" 4-1/4" 4" Spacer Req'd. Optional Outlet Mounting Holes Outlet 5-13/16" 2-1/4" 6-15/32" 3-1/2" 14-17/32" 3-3/16" SIDE VIEW END VIEW 30.0
31 Monarch Hydraulics, Inc. How to Order Your M-459 Mini System Select from the following options. Comprehensive performance data may be found on the page referenced below each selection category. MODEL M-459- PUMP MOTOR CAPACITOR RESERVOIR ACCESSORIES Ref. Page 9.0 Ref. Page 9.0 Ref. Page 9.0 Ref. Page 11.0 Ref. Page Horizontal Vertical 31.0
32 Monarch M-Series A.C. Hydraulic Power Systems MODEL M-458 Mini System Description: 7/16 SAE OR NPTF Pump/Motor/Valve/Reservoir Unit Check Valve Externally Adjustable Relief Valve 2-Way/2-Position Normally Closed Solenoid Operated Lowering Valve Cartridge Style Pressure Compensated Lowering Valve Outlet Port Options: Check Valve Port 7/16-20 SAE O-Ring or Face Port: 7/16-20 SAE O-Ring Horizontal Mounting Standard Vertical Mounting (Motor Up) Optional M HYDRAULIC SCHEMATIC M-458-S Lowering Valve Mounting Holes Relief Valve FILL LINE MONARCH 5-1/4" 4-1/4" 4" Spacer Req'd. Optional Outlet Mounting Holes Outlet 5-13/16" 2-1/4" 6-15/32" 3-1/2" 14-17/32" 3-13/16" SIDE VIEW END VIEW 32.0
33 Monarch Hydraulics, Inc. How to Order Your M-458 Mini System Select from the following options. Comprehensive performance data may be found on the page referenced below each selection category. MODEL M-458- PUMP MOTOR CAPACITOR RESERVOIR ACCESSORIES Ref. Page 9.0 Ref. Page 9.0 Ref. Page 9.0 Ref. Page 11.0 Ref. Page Horizontal Vertical 33.0
34 Monarch M-Series A.C. Hydraulic Power Systems MODEL M-419 Description: OUTLET PORT 3/8 NPTF Pump/Motor/Reservoir/Valve Unit Solenoid Operated 2-Way/2-Position Normally Closed Valve Externally Adjustable Relief Valve.375 Inch NPT Outlet Horizontal Mounting Standard Vertical Mounting (Motor Up) Optional M HYDRAULIC SCHEMATIC M-419-S Relief Valve Outlet 2" 7-5/16" 8-11/16" 1-3/8" "L" "A" 24-1/2" 1" 9" 1-5/8" 6-13/16" 8-1/8" SIDE VIEW END VIEW "L" dimension shown for motor is 10-11/16" "A" dimension for standard adapter is 2-5/32" "A" dimension for optional adapter is 3-11/32" Dimensions will vary according to motor output and manufacturer 34.0
35 Monarch Hydraulics, Inc. How to Order Your M-419 Power System Select from the following options. Comprehensive information may be found on the page referenced below each selection category. MODEL M-419- PUMP MOTOR RESERVOIR ACCESSORIES Ref. Page 5.0 Ref. Page 6.0 Ref. Page 10.0 Ref. Page Horizontal Vertical CLOSE COUPLED Ref. Page 8.0 M-419-C
36 Monarch M-Series A.C. Hydraulic Power Systems MODEL M-403 Description: Pump/Motor/Reservoir/Valve Unit Solenoid Operated 2-Way/2-Position Normally Closed Valve and Solenoid Operated 2-Way/ 2-Position Normally Open Valve Externally Adjustable Relief Valve.375 Inch NPT Outlet Horizontal Mounting Standard Vertical Mounting (Motor Up) Optional OUTLET PORT 1/4 NPT M HYDRAULIC M-403-S SCHEMATIC Outlet Relief Valve 8" 8-3/4" 1-3/8" "L" "A" 24-1/2" 1" 9" 1-5/8" 6-13/16" 8-1/8" SIDE VIEW END VIEW "L" dimension shown for motor is 10-11/16" "A" dimension for standard adapter is 2-5/32" "A" dimension for optional adapter is 3-11/32" Dimensions will vary according to motor output and manufacturer 36.0
37 Monarch Hydraulics, Inc. How to Order Your M-403 Power System Select from the following options. Comprehensive information may be found on the page referenced below each selection category. MODEL M-403- PUMP MOTOR RESERVOIR ACCESSORIES Ref. Page 5.0 Ref. Page 6.0 Ref. Page 10.0 Ref. Page Horizontal Vertical
38 Monarch M-Series A.C. Hydraulic Power Systems MODEL M-410 Description: Pump/Motor/Reservoir/Valve Unit 4-Way Manually Operated Valve Externally Adjustable Relief Valve.250 Inch NPT Outlets Horizontal Mounting Standard Vertical Mounting (Motor Up) Optional OUTLET PORTS 1/4 NPT "A" "B" M HYDRAULIC SCHEMATIC M-410-S Outlet Relief Valve 14-1/4" 8" 11" 1-3/8" "L" "A" 24-1/2" 1" 9" 1-5/8" 6-13/16" 8-1/8" SIDE VIEW END VIEW "L" dimension shown for motor is 10-11/16" "A" dimension for standard adapter is 2-5/32" "A" dimension for optional adapter is 3-11/32" Dimensions will vary according to motor output and manufacturer 38.0
39 Monarch Hydraulics, Inc. How to Order Your M-410 Power System Select from the following options. Comprehensive information may be found on the page referenced below each selection category. MODEL M-410- PUMP MOTOR RESERVOIR VALVES ACCESSORIES Ref. Page 5.0 Ref. Page 6.0 Ref. Page 10.0 Ref. Page 13.0 Ref. Page Horizontal Vertical CLOSE COUPLED Ref. Page 8.0 M-410-C
40 Monarch M-Series A.C. Hydraulic Power Systems MODEL M-452 Mini System Description: C1 C2 Pump/Motor/Valve/Reservoir Unit Check Valve 4-Way/2-Position Solenoid Cartridge Valve Mounts Directly to Unit 7/16-20 SAE O-Ring Outlet Horizontal Mounting Standard Vertical Mounting (Motor Up) Optional M HYDRAULIC M-452-S SCHEMATIC Mounting Holes Relief Valve FILL LINE MONARCH Directional Valve 5-1/4" 4" Outlet Port 2-1/3" Spacer Req'd. Optional Outlet Mounting Holes 5-13/16" 2-1/4" 6-15/32" 3-1/2" 14-17/32" 3-13/16" SIDE VIEW END VIEW 40.0
41 Monarch Hydraulics, Inc. How to Order Your M-452 Mini System Select from the following options. Comprehensive performance data may be found on the page referenced below each selection category. MODEL M-452- PUMP MOTOR CAPACITOR RESERVOIR ACCESSORIES Ref. Page 9.0 Ref. Page 9.0 Ref. Page 9.0 Ref. Page 11.0 Ref. Page Horizontal Vertical 41.0
42 Monarch M-Series A.C. Hydraulic Power Systems MODEL M-453 Mini System Description: OUTLET PORTS 1/4 NPT Pump/Motor/Reservoir/Valve Unit 4-Way/3-Position DO3 Solenoid Valve 7/16-20 SAE O-Ring Outlet Ports Horizontal Mounting Standard Vertical Mounting (Motor Up) Optional M HYDRAULIC SCHEMATIC M-453-S Mounting Holes Relief Valve Outlet Ports 7-3/4" 4" Spacer Req'd. Mounting Holes 5-13/16" 2-1/4" 6-15/32" 3-1/2" 14-17/32" 5-1/4" SIDE VIEW END VIEW 42.0
43 Monarch Hydraulics, Inc. How to Order Your M-453 Mini System Select from the following options. Comprehensive performance data may be found on the page referenced below each selection category. MODEL M-453- PUMP MOTOR CAPACITOR RESERVOIR VALVE ACCESSORIES Ref. Page 9.0 Ref. Page 9.0 Ref. Page 9.0 Ref. Page 11.0 Ref. Page 12.0/13.0 Ref. Page Horizontal Vertical 43.0
44 Monarch M-Series A.C. Hydraulic Power Systems MODEL M-406 Description: Pump/Motor/Reservoir/Valve Unit NPFA DO3 Valve Mounting Surface Externally Adjustable Relief Valve.250 Inch NPT Outlets Horizontal Mounting Standard Vertical Mounting (Motor Up) Optional OUTLET PORTS 1/4 NPT CETOP D03 MOUNTING PAD M HYDRAULIC M-406-S SCHEMATIC CETOP D03 Mounting Pad Outlet Relief Valve 8" 6-11/16" 1-3/8" "L" "A" 24-1/2" 1" 9" 1-5/8" 6-13/16" 8-1/8" SIDE VIEW END VIEW "L" dimension shown for motor is 10-11/16" "A" dimension for standard adapter is 2-5/32" "A" dimension for optional adapter is 3-11/32" Dimensions will vary according to motor output and manufacturer 44.0
45 Monarch Hydraulics, Inc. How to Order Your M-406 Power System Select from the following options. Comprehensive information may be found on the page referenced below each selection category. MODEL M-406- PUMP MOTOR RESERVOIR VALVES ACCESSORIES Ref. Page 5.0 Ref. Page 6.0 Ref. Page 10.0 Ref. Page 12.0 Ref. Page Horizontal Vertical
46 Monarch M-Series A.C. Hydraulic Power Systems MODEL M-405 Description: Pump/Motor/Reservoir/Valve Unit Externally Adjustable Relief Valve 4-Way/3-Position Solenoid Operated DO3 Valve. Standard Tandem Center Shown. Other Spool Types Available..250 Inch NPT Outlets Horizontal Mounting Standard Vertical Mounting (Motor Up) Optional OUTLET PORTS 1/4 NPT M HYDRAULIC M-405-S SCHEMATIC Outlet 7-7/8" 8" Relief Valve 3-11/16" 10-3/8" 6-11/16" 1-3/8" "L" "A" 24-1/2" 1" 9" 1-5/8" 6-13/16" 8-1/8" SIDE VIEW END VIEW "L" dimension shown for motor is 10-11/16" "A" dimension for standard adapter is 2-5/32" "A" dimension for optional adapter is 3-11/32" Dimensions will vary according to motor output and manufacturer 46.0
47 Monarch Hydraulics, Inc. How to Order Your M-405 Power System Select from the following options. Comprehensive information may be found on the page referenced below each selection category. MODEL M-405- PUMP MOTOR RESERVOIR VALVES ACCESSORIES Ref. Page 5.0 Ref. Page 6.0 Ref. Page 10.0 Ref. Page 12.0 Ref. Page STD Horizontal Vertical
48 Monarch M-Series A.C. Hydraulic Power Systems MODEL M-428 Description: Pump/Motor/Reservoir/Valve Unit Externally Adjustable Relief Valve Two 4-Way/3-Position Solenoid Operated Tandem Center DO3 Valves in One Two Station Manifold for Series Operation Maximum Relief Valve Setting 1400 PSI.375 Inch NPT Outlets Vertical Mounting M M-428-S HYDRAULIC SCHEMATIC 2-1/8" /4" 8-1/8" 6-13/16" 12-3/4" Outlet Ports B-A 25-5/8" Outlet Ports B'-A' 10-3/4" /4" 12-1/4" 48.0
49 Monarch Hydraulics, Inc. How to Order Your M-428 Power System Select from the following options. Comprehensive information may be found on the page referenced below each selection category. MODEL M-428- PUMP MOTOR RESERVOIR VALVES ACCESSORIES Ref. Page 5.0 Ref. Page 6.0 Ref. Page 10.0 Ref. Page 12.0 Ref. Page STD Vertical CLOSE CLOUPLED Ref. Page 8.0 M-428-C
50 Monarch M-Series A.C. Hydraulic Power Systems MODEL M-428-P Description: Pump/Motor/Reservoir/Valve Unit Externally Adjustable Relief Valve Two 4-Way/3-Position Solenoid Operated Tandem Center DO3 Valves in One Two Station Manifold for Parallel Operation.375 Inch NPT Outlets Vertical Mounting M M-428P-S 2-1/8" /4" 8-1/8" 6-13/16" HYDRAULIC SCHEMATIC 12-3/4" Outlet Ports B-A 25-5/8" Outlet Ports B'-A' 10-3/4" /4" 12-1/4" 50.0
51 Monarch Hydraulics, Inc. How to Order Your M-428-P Power System Select from the following options. Comprehensive information may be found on the page referenced below each selection category. MODEL M-428-P- PUMP MOTOR RESERVOIR VALVES ACCESSORIES Ref. Page 5.0 Ref. Page 6.0 Ref. Page 10.0 Ref. Page 12.0 Ref. Page STD Vertical CLOSE CLOUPLED Ref. Page 8.0 M-428-P-C
52 Monarch M-Series A.C. Hydraulic Power Systems MODEL M-466 Mini System Description: Pump/Motor/Reservoir/Valve Unit Cartridge Valve Block Manifolded Directly to Power Unit Controls 2 Single Acting Cylinders Independently.125 Inch NPT Outlets Horizontal Mounting Standard Vertical Mounting (Motor Up) Optional NOTE: Consult factory regarding return flow limitations. M M-466-S HYDRAULIC SCHEMATIC 14-17/32" 3-7/8" 5-13/16" 2-1/4" 6-15/32" FILL LINE MONARCH 6-1/2" SIDE VIEW Mounting Holes Outlet Ports END VIEW 52.0
53 Monarch Hydraulics, Inc. How to Order Your M-466 Mini System Select from the following options. Comprehensive performance data may be found on the page referenced below each selection category. MODEL M-466- PUMP MOTOR CAPACITOR RESERVOIR ACCESSORIES Ref. Page 9.0 Ref. Page 9.0 Ref. Page 9.0 Ref. Page 11.0 Ref. Page Horizontal Vertical 53.0
54 Monarch M-Series A.C. Hydraulic Power Systems MODEL M-457 Mini System Description: Pump/Motor/Reservoir/Valve Unit Independent Operation of Two Single Acting Master/Slave Cylinder Circuits Cartridge Valve Block Manifolded Directly to Power Unit.125 Inch NPT Outlets Horizontal Mounting Standard Vertical Mounting (Motor Up) Optional NOTE: Consult factory regarding return flow limitations. MASTER SLAVE MASTER SLAVE HYDRAULIC SCHEMATIC M 14-17/32" 3-7/8" 5-13/16" 2-1/4" 6-15/32" FILL LINE MONARCH 6-1/2" Slave Cylinder Return Ports SIDE VIEW Mounting Holes Outlet Ports END VIEW 54.0
55 Monarch Hydraulics, Inc. How to Order Your M-457 Mini System Select from the following options. Comprehensive performance data may be found on the page referenced below each selection category. MODEL M-457- PUMP MOTOR CAPACITOR RESERVOIR ACCESSORIES Ref. Page 9.0 Ref. Page 9.0 Ref. Page 9.0 Ref. Page 11.0 Ref. Page Horizontal Vertical 55.0
56 Monarch M-Series A.C. Hydraulic Power Systems NOTES: 56.0
Oildyne. 165 Series Hydraulic Power Units. Pressures to 241 bar (3500 psi) Flows to 5.4 lpm (1.4 gpm)
Oildyne Hydraulic Power Units Pressures to 241 bar (3500 psi) Flows to 5.4 lpm (1.4 gpm) 11 Power Unit Features We are pleased to introduce our new power units. The power units let you put more power where
Example. Fluid Power. Circuits
Example Fluid Power Circuits To Enhance Symbol Reading Skills To Work On Circuit Reading Skills With Answers HI LO Pump Circuit 18 A1 B1 17 16 15 13 Set 14 2,000 PSI PG2 Set 500 PSI 12 11 7 8 10 PG1 9
MONO BLOCK DIRECTIONAL CONTROL VALVE TS
SHIPPING: 2332 S 25TH STREET (ZIP 6815) MAILING: P.O. BOX #669 OMAHA, NE 6816 PHONE: (42) 344-4434 FAX: (42) 341-5419 HTTP://WWW.BRAND-HYD.COM MONO BLOCK DIRECTIONAL CONTROL VALVE TS TS312TSDTSTKJB TS2
MONO BLOCK DIRECTIONAL CONTROL VALVE TS1120TSLB
MONO BLOCK DIRECTIONAL CONTROL VALVE TS112TSLB TS TS212TSTSJB P T TS312TSDTSTKJ TS112TSJB FEATURES: O RG PORTS to eliminate leakage. POWER BEYOND CAPABILITY to fit your multi valve circuits. BUILT ANTI-DROP
In addition, a number of auxiliary options are available (para 2.7) as well as optional slices for special requirements (para 2.8).
DS3002 1. General Description This data sheet describes the Modular Power (MP) Electro Hydraulic Power Units, which have been designed to provide an advanced and flexible means of brake control. The MP
Solenoid Operated Directional Valves
INDUSTRIAL FLUID POWER COMPONENTS AND SYSTEMS SERIES 35 Solenoid Operated Directional Valves SF-2C-115A-35 S-1AY-12D-35 SD-2C-12D-35 Features High Flow/ High Pressure: Up to 40 gpm / 5000 psi working pressure*.
300 Series PA Pump and Cooler Assemblies
Type 300 Series PA Sizes 300 thru 370 (Page 1 of 9) 300 Series PA Pump and Cooler Assemblies Pump and Cooler Assemblies with Air/Oil Heat Exchanger When compact gear drives require assistance to dissipate
Solenoid Operated Directional Valves
INDUSTRIAL FLUID POWER COMPONENTS AND SYSTEMS SERIES 35 Solenoid Operated Directional Valves SD-2B-115A-35 SDS-2H-12D-35 S-2B-115A-35 Features High Flow/ High Pressure: Up to 25 gpm / 5000 psi working
PVH131/141 Variable Displacement Piston Pump - 11 Design
Service Data Vickers Piston Pumps PVH131/141 Variable Displacement Piston Pump - 11 Design Revised 05/01/97 M-2209-S Maximum Adjustable Stop S Option 913341 Locknut Torque 25-50 N.m. (18-37 lb. ft.) Torque
Hydraulic Trouble Shooting
Hydraulic Trouble Shooting Hydraulic systems can be very simple, such as a hand pump pumping up a small hydraulic jack, or very complex, with several pumps, complex valving, accumulators, and many cylinders
Fluid. Flu. Fluid Fluid. uid Power d Power P. Fluid Power P. Fluid Power. Fluid Power Power. d Power. Directional Cetop Valves DCV 03.
Catalogue Directional Cetop Valves DCV 03 Power Flu uid Power d Power P wer Power Power Power Power Power d Power Power Power ower Power Power wer Power Power P Power Power Powe d Power Power Power Power
Quiz On Information Learned From Chapter 1
Quiz On Information Learned From Chapter 1 1. Most hydraulic circuits are designed by: A. mechanical engineers. B. fluid power engineers. C. fluid power distributor salesmen. 2. Atmospheric pressure at
Cartridge Valves. Solenoid Valves. Vickers. Screw-in Cartridge Valves. Maximum Pressure 210 bar (3000 psi) Maximum Flow 227 l/min (60 USgpm)
Vickers Cartridge Valves Solenoid Valves Screw-in Cartridge Valves Maximum Pressure bar ( psi) Maximum Flow 7 l/min (6 USgpm) Rev /99 77 Introduction For over seventy years, Vickers has provided its customers
FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES
BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps. All the components subject to wear are contained
Series TMM Axial Piston Motor. Technical Information
Series TMM Axial Piston Motor Technical Information General Description GENERAL DESCRIPTION These motors are designed primarily to be combined with other products in closed circuit systems to transfer
LOADER DIRECTIONAL CONTROL VALVE LV LV22RFSTKLB SHOWN T
LOADER DIRECTIONAL CONTROL VALVE LV LV22RFSTKLB SHOWN T LV22RFSTKLB A2 B2 A1 B1 P LV22RFSTKABW FEATURES: O RING PORTS to eliminate leakage. FOURTH POSITION REGEN allows cylinder to rapidly extend. POWER
FAIRBANKS NIJHUIS FIRE PUMPS. www.fairbanksnijhuis.com
FAIRBANKS NIJHUIS FIRE PUMPS www.fairbanksnijhuis.com FAIRBANKS NIJHUIS Long established as a leading fire pump manufacturer, Fairbanks Nijhuis offers a broad range of horizontal and vertical split case,
Pressure Relief and Regulating Valves
Pressure Relief and Regulating Valves With blocked center directional valves and variable displacement pumps, or open center directional valves and fixed displacement pumps where fast response, low leakage
WILROY. Operation. Optional Diaphragm Rupture Detection HYDRAULICALLY ACTUATED DIAPHRAGM PUMP
WILROY ATEX Approved HYDRAULICALLY ACTUATED DIAPHRAGM PUMP Williams and Milton Roy have combined technologies to design a pump blending the proven mroy hydraulic by-pass diaphragm design with the Williams
PART 2 FORKLIFT HYDRAULIC SYSTEM
PART 2 FORKLIFT HYDRAULIC SYSTEM Chapter 1 Description and Operation Component Locations & Circuit Layouts 1 Hydraulic Pump 11 Control Valve 14 Valve Section Oil Flows 15 Anti-Cavitation Valve 22 Velocity
RPE3-04. Functional Description HA 4014 10/2010. Directional Control Valves Solenoid Operated. Replaces HA 4014 12/2007
Directional Control Valves Solenoid Operated RPE3-04 Size D 04 (02) 320 bar (4600 PSI) 30 L/min(8.0 GPM) HA 4014 10/2010 Replaces HA 4014 12/2007 4/3-, 4/2- way directional control valves with solenoid
*Rated to 207 Bar/3000 PSI with Aluminum Body. Denotes New Winner s Circle Product Line. Catalog HY15-3502/US
Bodies & Contents SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. LPM/GPM BAR/PSI STANDARD CHECKS D1A6... 2U... Valve Insert, Ball Type...145/38... 42/6... 5 D1B125... 2C... Valve Insert, Ball Type...
FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES
BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps. All the components subject to wear are contained
Variable Displacement Pump AA10VSO
Variable Displacement Pump AA10VSO Series 31, Industrial Model, for Open Circuits Axial piston, swashplate design Brueninghaus Hydromatik Sizes 28...140 Nominal pressure 4000 psi Peak pressure 5100 psi
MANTA Piston Distributor for Oil and Fluid Grease
MANTA Piston Distributor for Oil and Fluid Grease Function Piston distributors meter out and distribute the oil delivered by an intermittently actuated pump. The quantities of oil for the individual lube
FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES
BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps. All the components subject to wear are contained
TECHNICAL BROCHURE B5-33GB 5GB, 7GB, 10GB, 18GB, 25GB, 33GB HIGH PRESSURE MULTI-STAGE BOOSTER PUMP
TECHNICAL BROCHURE B-33GB GB, 7GB, 1GB, 18GB, 2GB, 33GB HIGH PRESSURE MULTI-STAGE BOOSTER PUMP FEATURES Multi-stage Design: Provides steady, quiet, vibration free, operation. Optional Stainless Steel Construction:
Series PVP Variable Volume Piston Pumps
Series PVP Variable Volume Piston Pumps Catalog HY28-2662-CD/US Revised June, 212 hpm12-1.p65, lw, jk 1 Notes Series PVP hpm12-1.p65, lw, jk 2 Introduction Series PVP Series Sizes 6-14 Phased Out For Reference
26 3213.13 Diesel Engine Driven Generators Page 1 of 6
Last Update: December 8, 2014 A. Description of System Consultant s Handbook Page 1 of 6 1. Provide a diesel engine driven electric generating unit, factory assembled, tested and certified to operate at
Fire Pump Plan Review March 2010
Fire Pump Plan Review March 2010 Date of Review: / / Permit Number: Business/Building Name: Address of Project: Designer Name: Designer s Phone: Contractor: Contractor s Phone: Occupancy Classification:
*Rated to 207 Bar/3000 PSI with Aluminum Body. Catalog HY15-3501/US SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO.
Bodies & Contents SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. /GPM BAR/PSI STANDARD CHECKS D1A6... 2U... Valve Insert, Ball Type...145/38... 42/6... 5 D1B125... 2C... Valve Insert, Ball Type... 5/132...
Unit 24: Applications of Pneumatics and Hydraulics
Unit 24: Applications of Pneumatics and Hydraulics Unit code: J/601/1496 QCF level: 4 Credit value: 15 OUTCOME 2 TUTORIAL 4 DIRECTIONAL CONTROL VALVES The material needed for outcome 2 is very extensive
SMR Series Submicronic Removal Fluid Purifi cation Systems
SMR Series Submicronic Removal Fluid Purifi cation Systems 193 SMR Series Applications The SMR Series is the smart purification solution for fluid flow in the 2-10 GPM (8-38 LPM) range. The SMR contains
TorqPlus TM Electric Valve Actuators and Controls
TorqPlus TM Electric Valve Actuators and Controls Torque 150 IN/LB 600 IN/LB The Engineered Solution Bettis TorqPlus quality line of electric actuators are designed for quarter turn applications ball,
3-Way heavy duty flow control, with pressure compensated and solenoid controlled priority flow
1/6 RE 18309-3/06.10 Replaces: RE 18309-3/04.10 3-Way heavy duty flow control, with pressure compensated and solenoid controlled priority flow A-VRFC3C-VEI-VS 0M.43.20.80 - Y - Z Description The flow control
2 WAY (2/2) AND 3 WAY (3/2) BRASS AND STAINLESS STEEL SOLENOID VALVES
2 WAY (2/2) AND 3 WAY (3/2) BRASS AND STAINLESS STEEL SOLENOID VALVES DIRECT ACTING Brochure N-289 SPECIFICATIONS Port Size: 1/8 and1/4 Solenoid Valve for air, oil, water and other fluids Flow Direction:
Centro-Matic Automatic Lubrication Systems System Controls
Selecting the right controls for your automated lubrication system is one of the last steps in the design process. Several different models may be chosen to control power-operated pumps, depending on the
Catalog HY15-3501/US SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. LPM/GPM BAR/PSI
Bodies & Contents SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. LPM/GPM BAR/PSI KSWA3... SW-3... Ball sert Type...9./2.... 42/6... 3 K2A... 3Z... Poppet sert Type...38/1... 3/... 4 CS41B... C4-3...
Pump Specifications 250 Series Submersible Sump / Effluent Pump 2 Solids handling
Pump Specifications 250 Series Submersible Sump / Effluent Pump 2 Solids handling 250_P1 R10/7/2015 Copyright 2015 Liberty Pumps Inc. All rights reserved. Specifications subject to change without notice.
An SPX Process Equipment Operation. Universal II Industrial Series Rotary Positive Displacement ECP Pumps
An SPX Process Equipment Operation Universal II Industrial Series Rotary Positive Displacement ECP Pumps New levels of performance. Reduced operational and maintenance costs. For more than half a century,
2-Way heavy duty flow control, with pressure compensated, solenoid and load sensing controlled priority flow
2-Way heavy duty flow control, with pressure compensated, solenoid and load sensing controlled priority flow RE 18309-64/04.10 1/6 Replaces: RE 00171/02.07 A-VRFC2C-VEI-VS-LS 0M.28.03.80 - Y - Z Description
Rexroth Hydraulic Pump A10VO Series User Manual
Rexroth Hydraulic Pump A10VO Series User Manual Rexroth Hydraulic pump A10VO Series User Manual Revised 5/1/2009 Page 1 of 12 Functional Purpose This pump is preferred over a fixed displacement (gear)
4 Posiflow Proportional Solenoid Valves
4 Posiflow Solenoid Brass or Stainless Steel Bodies 1/4" to 1/2" NPT 2/2 Features Flow rates adjustable between 0% and 100% of rating Flow rate can also be regulated by a range of electrical inputs (sensors,
! WARNING. McDonnell & Miller Installation & Maintenance Instructions MM-217(I) Series 150S and 157S (Snap Switch, All Models except 157S-RB-P)
Series 150S and 157S (Snap Switch, All Models except 157S-RB-P) Low Water Cut-Off/Pump Controllers For Steam Boilers and Other Level Control Applications McDonnell & Miller Installation & Maintenance Instructions
Hydraulic Troubleshooting PRESENTED BY
Hydraulic Troubleshooting PRESENTED BY NORMAN KRONOWITZ Introduction Welcome to the CMA/Flodyne/Hydradyne s Hydraulic Troubleshooting presentation. We will introduce many aspects of troubleshooting hydraulic
Uniquely designed and engineered specifically for the pulp and paper industry.
Universal SPU2 Series Uniquely designed and engineered specifically for the pulp and paper industry. For more than half a century, Waukesha Cherry-Burrell has been a leader in the design, manufacturing
WHAT YOU DON T KNOW ABOUT ACCUMULATORS CAN KILL YOU!
WHAT YOU DON T KNOW ABOUT ACCUMULATORS CAN KILL YOU! Atlanta (Monroe) GA 770-267-3787 gpm@gpmhydraulic.com www.gpmhydraulic.com What You Don t Know About Hydraulic Accumulators Can Kill You TABLE OF CONTENTS
PRODUCT CARD GEAR PUMPS AND MOTORS ORS GROUP 1 E0.14.0503.02.01 TM GEAR PUMPS AND MOTORS GROUP 1 INDEX Page 1 - GENERAL INDEX Page 2 - Features - Quick guide Page 3 - Features - General - Working conditions
MOBILE FIRE - RESCUE DEPARTMENT FIRE CODE ADMINISTRATION
MOBILE FIRE - RESCUE DEPARTMENT FIRE CODE ADMINISTRATION Fire Pump Plan Review 2009 International Fire Code and NFPA 20 Date of Review / / BLD201 - Project Address: Project Name: Contractor s Business
GE Oil & Gas. Texsteam * Pumps: precise chemical injection pumping
GE Oil & Gas Texsteam * Pumps: precise chemical injection pumping 2 With a wide range of capacities and operating pressures, GE s versatile Texsteam pumps can handle challenging chemical pumping requirements
ROTARY GEAR FLOW DIVIDERS
ROTARY GEAR FLOW DIVIDERS Concentric AB Innovation + Technology = Sustainability GC and D Series Rotary Gear Flow Dividers Intensifier - Combiner (European and U.S. Versions) Field-proven Concentric Hydraulic
Hydraulic Motor/Pump. Series F11/F12 Fixed Displacement. parker.com/pmde
Hydraulic Motor/Pump Series F11/F12 Fixed Displacement parker.com/pmde Series F11/F12 Torque (M) M = D x p x η hm 63 [Nm] Conversion factors 1 kg... 2.20 lb 1 N... 0.225 lbf 1 Nm... 0.738 lbf ft 1 bar...14.5
HIGH PRESSURE TECHNOLOGY HYDRAULICS PNEUMATICS TESTING EQUIPMENT
HIGH PRESSURE TECHNOLOGY HYDRAULICS PNEUMATICS TESTING EQUIPMENT MAXIMATOR GmbH 2 MAXIMATOR has an extensive know-how concerning concept, development, construction and manufacturing of test benches and
DIRECTIONAL CONTROL VALVES
Series 35 High Flow High Pressure Directional Valves D05SD DIN Type D05S Electrical Box Type D03SD DIN Type D03S Electrical Box Type D03SL Lead Wire Type (D05SL Lead Wire Type Also available) FEATURES
Truck Hydraulics. F1 F2 T1 VP1 PTO info Accessories. Fixed and Variable Displacement Pumps, Motors and Accessories. Catalogue HY17-8200/UK March 2004
Fixed and Variable Displacement Pumps, Motors and Accessories Catalogue HY17-8200/UK March 2004 F1 F2 T1 VP1 PTO info Accessories Conversion factors 1 kg 2.20 lb 1 N 0.225 lbf 1 Nm 0.738 lbf ft 1 bar 14.5
Power Cube Open Source Ecology Page 1. Power Cube. Version 4
Power Cube Open Source Ecology Page 1 Power Cube Version 4 Power Cube Open Source Ecology Page 2 Contents Table of Contents Power Cube... 1 Contents...2 Introduction... 3 Bill Of Materials...4 Discrete
15/40/80CN Series Coreless Medium Pressure Filters
//8CN Series Coreless Medium Pressure Filters //8CN Series Applications Compressor Lube Oil Off-line Filter Loops Machine Tools (Automotive Standard) Hydrostatic Drive Charge Pumps Mobile Equipment Pilot
Radial piston pumps type R and RG
Radial piston pumps type R and RG Operating pressure p max = 700 bar Delivery flow Q max = 91.2 lpm (at 1450 rpm) Geometric displacement V g max = 64.2 cm 3 /rev. 1. General Motor pumps and hydraulic power
Unit 24: Applications of Pneumatics and Hydraulics
Unit 24: Applications of Pneumatics and Hydraulics Unit code: J/601/1496 QCF level: 4 Credit value: 15 OUTCOME 2 TUTORIAL 1 HYDRAULIC PUMPS The material needed for outcome 2 is very extensive so there
PM10 VARIABLE DISPLACEMENT PUMP CLOSED LOOP CIRCUIT
PM10 VRIBLE DISPLCEMENT PUMP CLOSED LOOP CIRCUIT T E C H N I C L C T L O G PM10 - Variable displacement pump POCLIN HYDRULICS OVERVIEW PM10 is a variable displacement, axial piston pump, with swashplate
Model 1210C Battery Powered Pump Shown. Description
12 Volt DC Rotary Vane Pump Series 1200C Model 1210C Battery Powered Pump Shown Description of Included Models Model Number FR1205C FR1210C FR1211C FR2410C FR2411C Description Basic 12 volt DC pump with
Horizontal Jet Pumps 1/3-1-1/2 HP
Horizontal Jet s 1/3-1-1/2 FW01 0909 Supersedes 0409 The CPJ, CPH and EK models feature the famous Flint and Walling Service Plus motor, available in either NEMA J or Uni-frame flange construction. The
ZU4-Series, Portable Electric Pumps
ZUSeries, Portable Pumps Shown from left to right: ZU30ME, ZUSEH, ZU30PEK Tough. Dependable. Innovative. ZUSeries Features and Options For special requirements see factory installed features and options.
The Secret of Hydraulic Schematics. BTPHydraulics www.iranfluidpower.com
The Secret of Hydraulic Schematics BTPHydraulics www.iranfluidpower.com www.iranfluidpower.com Table of Contents The Secret to Reading and Interpreting Hydraulic Schematics... 1 Hydraulic System Schematics...
LINEAR MOTION CONTROL
LINEAR MOTION CONTROL Technical Data Sheet Static Locks RLSS Series Nexen s new generation of linear holding/locking devices take rod locking technology to the next level. With superior performance, these
The conditions below apply to the curves shown on the following pages.
GENERAL INFORMATION STAINLESS STEEL, SILVERLINE, EVERGREEN & GOLDLINE SERIES PERFORMANCE CURVE CONDITIONS The conditions below apply to the curves shown on the following pages. a. The Performance curves
SKP Series SKP15U.. Gas Valve Actuator with Safety Shutoff Function
SKP Series SKP15U.. Gas Valve Actuator with Safety Shutoff Function Document No. 155-751 SKP15U.. Description Only when assembled to Series VGU Gas valves SKP15 electro-hydraulic actuators combine with
Standard Specifications Model. How to Order. Mist spray unit. Recommended Equipment. Mixing valve
Mist Spray Unit Series MU/ Intermittent spray to cutting and press gear chains, etc. Standard Specifications MU MU Inlet air Oil tank set range. MPa. to. MPa Oil tank capacity (cm ) Total capacity: Effective
Series 30000 Hose Reels
Operating Instructions and Parts List for Series 30000 Hose Reels - MANUAL DRIVEN - - POWER DRIVEN - SAFETY PRECAUTIONS Personal injury and/or equipment damage may result if proper safety precautions are
BERMAD Waterworks. Quick Active Check Valve. 700 Series. Model 740Q. Features and Benefits. Major Additional Features
Booster Pump Control Valve Quick Active Check Valve Isolates system from the effects of pump starts and stops for: Solitary single speed pumps Battery of single speed pumps (add & switch) Battery of variable
3 WAY (3/2) POPPET VALVES FOR AIR AND VACUUM SERVICE SOLENOID OR AIR ACTUATED BROCHURE N-223
3 WAY (3/2) POPPET VALVES FOR AIR AND VACUUM SERVICE SOLENOID OR AIR ACTUATED BROCHURE N-223 HERION S HIGH PERFORMANCE POPPET VALVES For those applications requiring high Cv, fast response times, large
Heating, Ventilation, Air Conditioning and Refrigeration (HVACR)
Heating, Ventilation, Air Conditioning and Refrigeration (HVACR) I. Demonstrate safety skills in typical HVACR work situations to NATE Core Installer Knowledge Areas for Technician Excellence for Safety
Kobelco Extended Warranty Program. www.kobelco-europe.com
Kobelco Extended Warranty Program www.kobelco-europe.com Kobelco Extended Warranty is a convenient, value added way to give your Kobelco customers added security and peace of mind. Benefits of the Kobelco
Pressure Relief. Pressure Control Valve R(C)G(O)-03, 06 and 10; R(C)T(O)-03, 06 and 10 VICKERS. Basic Characteristics. Sectional Illustrations
VICKERS Pressure Relief Pressure Control Valve R(C)G(O)-03, 06 and 10; R(C)T(O)-03, 06 and 10 Sectional Illustrations RCG-** Model Shown RCT-** Model Shown Basic Characteristics Type...................
OUR PRODUCTS TRH-TRS-TRM-TRV. LIQUID RING VACUUM PUMPS AND COMPRESSORS Capacity up to 2100 ACFM Vacuum to 29 Hg. Our Other Products.
Our Other Products OUR PRODUCTS Liquid Ring & Rotary Vane Vacuum Pumps and Systems Liquid Ring Vacuum Pumps: 3 CFM to,000 CFM Liquid Ring Compressors up to 1 psig Heat Transfer Pumps for hot thermal oils
VSO MAX HP High Flow Proportional Valve
VSO MAX HP High Flow Proportional Valve Typical Applications Ventilators Insufflators Anesthesia Delivery & Monitors Pressure & Flow Control Mass Flow Control Product Specifications Physical Properties
Valve Proving System VPS 504 Series S06 (120 VAC) Series S05 (24 VDC)
Valve Proving System VPS 504 Series S06 (120 VAC) Series S05 (24 VDC) VPS 504 S06 (120 VAC) is: CSA Certified File # 1637485 CSA Requirement No. 4-01 (USA) Technical Information Letter R-15 (Canada) UL
NORMAN FILTER COMPANY PRODUCT OVERVIEW
NORMAN FILTER COMPANY PRODUCT OVERVIEW LEADING THE WAY IN QUALITY FILTRATION WWW.NORMANFILTERS.COM FILTER ELEMENT INTERCHANGE Tee-Type Filter 4500, 14500, 34500, and 54500 Series Mini Tee-Type Filter 4100
VARIABLE DISPLACEMENT AXIAL PISTON PUMPS. For truck applications
VARIABLE DISPLACEMENT AXIAL PISTON PUMPS For truck applications TVP FEATURES Variable displacement axial piston pumps swash plate design ideally suited for open circuit truck applications. The compact
Flow Control Valves. Note: Also see R04C3 on page DC1. Denotes New Winner s Circle Product Line. Catalog HY15-3502/US
Catalog HY15-352/US Contents Control SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. LPM/GPM BAR/PSI NEED VALVES J2A2... C8-2... Needle Valve, Cartridge Type...45/12... 42/6... 5-6 NVH81... C8-2... Needle
DIESEL & JET FUEL FILTRATION EQUIPMENT. Applications:
E X T E N D I N G Y O U R E N E R G Y DIESEL & JET FUEL FILTRATION EQUIPMENT Applications: Back-Up Diesel Generators Gas Turbines Fueling Terminals for Trucks & Buses Marine Mining Railroad Agriculture
Schematic Symbols Chart (Design Hydraulic and Pneumatic circits)
Page 1 of 6 (Home) Symbols / Visit us on: Fluid Power, Automation and Motion Control for all Industries About Us Products Services Catalogs Place an Order Training & Information Contact Us Employee Access
Pressure Switch for gas and air
Switch for gas and air GAO-A4 GMH-A4 GML-A4 UL Listed UL 353 File # MH 16628 CSA Certified CSA C22.2 No. LR 53222 Certification file # 201527 FM Approved Class 3510, 3530 File # J.I. 1Y919.AF Commonwealth
Manapak Sandwich Valves Series CM, CPOM, FM, PRDM, PRM, RM
Introduction Manapak valves provide a variety of check, flow control, pressure relief and pressure reducing functions in a compact NFPA D03, D05 and D08 sandwich style valve. The NFPA D03 valve body conforms
Mono-Block II Installation & Operation Manual
Mono-Block II Installation & Operation Manual Enraf Fluid Technology UK, Ltd. Enraf Fluid Technology USA, Inc. 6 Pennant Park, Standard Way 2000 Northfield Court Fareham, Hampshire, England PO16 8XU Roswell,
» 30,000 to 60,000 lb. capacity» Single and tandem axle
ROLL-OFF CABLE HOISTS Tel: 800.285.0666 sales@wastequip.com www.wastequip.com Extendable Tail (EX) cable hoists are ideal for areas with clearance issues that require a low loading height.» 30,000 to 60,000
Industrial Hydraulic Remote Controlled Monitor
Industrial Hydraulic Remote Controlled Monitor Models: 294-11XBHC-N4X, 294-11XBHC-N7/4, 299-20XHC-N4X, & 299-20XHC-N7/4 Installation, Operating, & Maintenance Instructions 1302 WEST BEARDSLEY AVENUE P.O.
Multistage high-pressure multistage centrifugal pumps
Series description Wilo-Helix V 2 4 6 8 Wilo-Helix V 19-27 7 6 6 Hz - North America 22 2 18 5 16 14 4 12 3 1 V 1 V 19 V 27 8 2 6 1 5 1 15 2 25 3 4 2 35Q[US gpm] H[ft] H[m] Design Vertical multi-stage,
Valves. Sub-Base Mounted Valves to ISO 5599/2
Valves Sub-Base Mounted Valves to ISO 5599/2 General Information ISO 1, ISO 2 and ISO 3 valve series incorporate the famous Numatics lapped spool and sleeve for ultimate service life. Due to the great
Hydraulic Flow Control Valves
Webtec Products Limited Hydraulic Flow Control Valves Quality Hydraulic Components from the Webtec Range CONTENTS DESCRIPTION PAGE No. ILFC Series Fixed Flow Pressure Compensated Control Valve 1 VFC Series
220 Series Piston Pump Typical Applications Features and Benefits
Introduction 220 Series Piston Pump Eaton s new 220 Series piston pump signifies a step change in the generation of hydraulic power. Utilizing the latest developments in hydraulic pump technology, the
Check Valves Valve locator
Check Valves Valve locator Functional Symbol Flow Typical Model Cavity Rating Pressure Page Check valve, direct L/min (USgpm) bar (psi) FPR/4 Inline () 5 (5) - FPR/8 Inline (8) 5 (5) - FPR/ Inline 45 ()
We will discuss common industrial applications with guides for the proper use of electric motors on these.
INTRODUCTION: Baldor Electric Company has prepared this Specifiers Guide to help you cover all the bases when you are specifying electric motors. It will cover in a generic way most of the subjects which
Specifying a Variable Frequency Drive s
Specifying a Variable Frequency Drive s Put on by Bruce Reeves and Jeremy Gonzales Dykman Electrical Covering the Western US For all of your VFD and Soft Start and Motor Needs How To Specify a Variable
Product Brochure. Controlled start transmission
Product Brochure Controlled start transmission What CST does The Dodge CST (Controlled Start Transmission) is a 2 in 1 gearbox which combines a planetary gear reducer with an integral wet clutch system.
Vickers. Check Valves. Check Valves. Inline, right angle, manifold mounted, and pilot operated designs. Released 9/93
Vickers Check Valves Check Valves Inline, right angle, manifold mounted, and pilot operated designs Released 9/93 645 Introduction Vickers inline, right-angle, and manifold mounted check valves are direct
ETZGAR CONVEYOR COMPANY Controls Section v12.05
Section 7 Controls Page Description 7-1 Controls Index 7-2 Motor Data, Enclosure Rating and Abbreviations 7-3 Controls Safety Guidelines 7-4 Fixed Speed Controls Packages 7-5 Three Phase AC Variable Speed
Compressors, Chillers & Condensers
Chillers & Condensers SUCTION CUTOFF UNLOADING VS HOT GAS BYPASS UNLOADING Suction Cutoff Unloading Head Hot Bypass Unloading Head Suction cutoff unloading is a more efficient unloading method for the
Pump Specifications 405 Series Commercial Drain Pump (High-Temp) 2 Solids handling
Pump Specifications 405 Series Commercial Drain Pump (High-Temp) 2 Solids handling 405_P1 R1/27/2012 Copyright 2012 Liberty Pumps Inc. All rights reserved. Specifications subject to change without notice.
SCP 012-130 ISO. Other advantages: SCP 012-130 ISO is a series of piston pumps with a fixed displacement for mobile and stationary hydraulics.
SCP 012-130 ISO is a series of piston pumps with a fixed displacement for mobile and stationary hydraulics. SCP 012-130 ISO covers the entire displacement range 12-130 cmᶟ rev. at a maximum pressure of