Custom Seal (PVC) ROOFING DETAILS

Transcription

1 Custom Seal (PVC) ROOFING DETAILS DETAIL... PAGE PVC-1.01 Wall Termination W/Term Bar... 1 PVC-1.02 Wall Termination W/Counter Flashing... 1 PVC-1.03 Parapet Wall Coping Cap... 2 PVC-1.04 Wall Termination W/ Term Bar and Wood Nailer... 2 PVC-1.05 Prefabricated Wall Base Flashing Factory Tab on Deck... 3 PVC-1.06 Wall Base Flashing Factory Tab on Wall... 3 PVC-1.07 Wall Base Flashing Tab on Deck... 4 PVC-1.08 Wall Base Flashing Existing Cant Tab on Deck... 4 PVC-1.09 Wall Base Flashing Existing Cant Tab on Wall... 5 PVC-1.10 Wall Base Flashing Wood Nailer... 5 PVC-1.11 Wall Base Flashing W/ High Parapet... 6 PVC-1.12 Wall Termination Wall Base Flashing... 6 PVC-1.13 Sloped Wall Transition... 7 PVC-1.14 Curb/Skylight Flashing... 7 PVC-1.15 Curb/Skylight Detail... 8 PVC-1.16 Roof Hatch Detail... 8 PVC-1.17 Sleeper Detail... 9 PVC-1.18 Sleeper Curb Detail... 9 PVC-1.19 Custom Seal Mechanically Attached...10 PVC-1.20 Prefabricated Closed Pipe Boot...10 PVC-1.21 Prefabricated Open Pipe Boot...11 PVC-1.22 Lightning Rod Detail...11 PVC-1.23 Prefabricated Hot Stack Flashing...12 PVC-1.24 Sump Roof Detail Option...12 PVC-1.25 Existing/New Sump Roof Drain...13 PVC-1.26 Roof Drain Insert...13 PVC-1.27 Flat Expansion Or Control Joint...14 PVC-1.28 Raised Expansion Joint...14 PVC-1.29 Expansion Joint Base of Wall...15 PVC-1.30 Gutter Termination...15 PVC-1.31 Custom Seal 2/34 Fascia Bar/Cover...16 PVC /34 Fascia Bar Raised To Creat Gravel Stop...16 PVC-1.32a PVC Coated Metal Gravel Stop/Drip Edge...17 PVC-1.32b Snap on Two Piece Fascia Assembly...17 PVC-1.32c PVC Coated Metal Gravel Stop/Drip Edge...18 PVC-1.32d PVC Coated Metal Gravelstop...18 PVC-1.32e Gravelstop Scupper Fabricated With (PVC) Coated Metal...19 PVC-1.33 Custom Seal Term Bar Over Edge...20 PVC-1.34 Walkway Pad...20 PVC-1.35 Concrete Walkway Paver...21 PVC-1.36 Pipe Support...21 PVC-1.37 System Tie In...22 PVC-1.38 Valley Tie In...22 PVC-1.39 System Tie In...23 PVC-1.40 Threshold Termination...23

2 PVC-1.41 Custom Seal Two Way Breather Vent...24 PVC-1.42 Prefabricated 12 or Larger Stack Flashing...24 PVC-1.43 Custom Seal Prefabricated Curb Flashing...25 PVC-1.44 Prefabricated Outside Corner...25 PVC-1.45 Prefabricated Outside Corner...26 PVC-1.46 Prefabricated Scupper View PVC-1.47 Prefabricated Scupper View PVC-1.48 Typical Factory Prefabricated Panel Detail...27 PVC-1.49 Typical Factory Prefabricated Panel Detail...28 PVC Tab System or 24 6 Tab System...28 PVC-1.51 Custom Seal Membrane Re-Roof Over Standing Seam Metal Roof...29

3 CAULK FASTENER EVERY HOLE Wall Termination W/ Term Bar Detail #: PVC-1.01 METAL COUNTER FLASHING (BY OTHERS) USE OF EXISTING METAL COUNTER FLASHING TO ALLOW SYSTEM TO VENT FASTENER EACH 24" O.C. MAX. Wall Termination W/ counter flashing Detail #: PVC-1.02

4 METAL COPING FASTENER FASTENER PER METAL MANUFACTURER REQUIREMENTS CAULK AROUND FASTENER METAL CLIP TREATED W OOD NAILER FASTENER 24" O.C. Parapet Wall Coping Cap Detail #: PVC-1.03 CAULK TERMINATION BAR FACTORY W ELD PARAPET W ALL PREFABRICATED PARAPET W ALL FLASHING FIELD ROOF DECK Wall Termination W/ Term Bar and Wood Nailer Detail #: PVC-1.04

5 FACTORY W ELD SEAM PLATE OR METAL BAR ANCHOR 1 1/2" HOT AIR W ELD FASTENER 12" O.C. INSULATION 4" MAX. FROM DECK W/OUT TREATED WOOD NAILER Prefabricated Wall Base Flashing Factory Tab on Deck Detail #: PVC-1.05 FACTORY W ELD 1 1/2" HOT AIR W ELD FASTENER 12" O.C. INSULATION 4" MAX. FROM DECK W/OUT TREATED WOOD NAILER Wall Base Flashing Factory Tab on Wall Detail #: PVC-1.06

6 FACTORY W ELD SEAM PLATEOR METAL BAR ANCHOR 1 1/2" HOT AIR W ELD FASTENER 12" O.C. Wall Base FlashingTab on Deck Detail #: PVC-1.07 SEAM PLATE OR METAL BAR ANCHOR EXISTING CANT 1 1/2" HOT AIR FASTENER 12" O.C. W/OUT TREATED 4" MAX. FROM DECK INSULATION WOOD NAILER Wall Base Flashing Existing Cant Tab on Deck Detail #: PVC-1.08

7 SEAM PLATE OR METAL BAR ANCHOR FACTORY W ELD 1 1/2" HOT AIR FASTENER 12" O.C. EXISTING CANT Wall Base Flashing Existing Cant Tab On Wall Detail #: PVC-1.09 INSULATION 4" MAX. FROM DECK W/OUT TREATED WOOD NAILER 2X4 ANCHORED TO DECK (WHERE REQ'D.) FACTORY W ELD SEAM PLATE OR METAL BAR ANCHOR 1 1/2" HOT AIR FASTENER 12" O.C. Wall Base Flashing Wood Nailer Detail #: PVC-1.10 INSULATION 4" MAX. FROM DECK W/OUT TREATED WOOD NAILER

8 SEAM PLATE OR METAL BAR ANCHOR W/ FASTENER 12" O.C. FACTORY W ELD SHOWN WITH OPTIONAL HOT AIR FACTORY W ELD RAIN SHEILD REINFORCED HOT AIR FACTORY W ELD 1 1/2" HOT AIR Wall Base Flashing W/High Parapet Detail #: PVC-1.11 INSULATION 4" MAX. FROM DECK W/OUT TREATED WOOD NAILER NOTE: FIRST PARAPET TAB MUST BE NO MORE THAN 24" FROM BASE FACTORY W ELD PLATE OR METAL BAR ANCHOR W/ FASTENERS 24" MAX. FACTORY W ELD 1 1/2" HOT AIR W ELD Wall Termination Wall Base Flashing Detail #: PVC-1.12

9 FASTENER WATERSTOP SHINGLES (2 FULL COURSES OVER ) 1 1/2" HOT AIR TREATED W OOD NAILER (SEE BELOW) FASTENER 12" O.C. FASTENER 24" O.C. NOTE: ACCEPTABLE ROOFING NAILS MAY BE USED AT 4" O.C. PROVIDING A TREATED WOOD NAILER IS PRESENT Sloped Wall Transition Detail #: PVC-1.13 METAL CAP OR COUNTER FLASHING USED TO ALLOW SYSTEM TO VENT) (EXISTING METAL FLASHING CAN BE FASTENER 24" O.C. MAX. METAL BAR ANCHOR W/ FASTENER 18" O.C. MAX. 1 1/2" HOT AIR W ELD Curb/Skylight Flashing Detail #: PVC-1.14 INSULATION 4" MAX. FROM DECK W/OUT TREATED WOOD NAILER

10 METAL CAP OR COUNTERFLASHING NAIL EACH 18" O.C. MAX. TREATED W OOD NAILER 1 1/2" HOT AIR FASTENER 18" O.C. MAX. INSULATION 4" MAX. FROM DECK W/OUT TREATED WOOD NAILER METAL BAR ANCHOR / PLATE Curb/Skylight Detail Detail #: PVC-1.15 METAL CAP OR COUNTERFLASHING (BY OTHERS) RUBBER ROD STOCK LARGER THAN OPENING (BY OTHERS) SET IN BONDING ADHESIVE TREATED W OOD NAILER 1 1/2" HOT AIR METAL BAR ANCHOR OR PLATE FASTENER 18" O.C. MAX. Roof Hatch Detail Detail #: PVC-1.16 INSULATION 4" MAX. FROM DECK W/OUT TREATED WOOD NAILER

11 MECHANICAL UNIT PROTECTION PAD TREATED W OOD SLEEPER TREATED W OOD INSULATION 4" MAX. FROM DECK W/OUT TREATED WOOD NAILER SUBSRTATE Sleeper Detail Detail #: PVC-1.17 METAL CAP (BY OTHERS) WATERSTOP EQUIPMENT SUPPORT ANCHOR BOLT W / NEOPRENE WASHER METAL BAR ANCHOR OR PLATE FASTENER 18" O.C. MAX. W ITH CAULK 1 1/2" HOT AIR 4" MAX. FROM DECK W/OUT TREATED WOOD NAILER FASTENER 24" O.C. TREATED W OOD NAILER FASTENER 18" O.C. MAX. Sleeper Curb Detail Detail #: PVC-1.18

12 1 1/2" HOT AIR SEAM DISC INSULATION FASTENER (SEE SYSTEM REQUIREMENTS) Custom Seal Mechanically Attached Detail #: PVC-1.19 PIPE WATERSTOP CAULK CLAMPING RING 1 1/2" MIN. HOT AIR W ELD PREFAB. PIPE BOOT (CLEAN FLANGE BEFORE INSTALLING) Prefabricated Closed Pipe Boot FOR (1" TO 3") (3" TO 6") (6" TO 9") (9" TO 12") PIPE SIZES Detail #: PVC-1.20

13 PIPE 1 1/2" MIN. HOT AIR W ELD CAULK WATERSTOP CLAMPING RING PREFAB. PIPE BOOT (CLEAN FLANGE BEFORE INSTALLING) INSULATION 1" TO 3" PIPE SIZES 3" TO 5" PIPE SIZES 5" TO 9" PIPE SIZES 9" TO 12" PIPE SIZES *NOTE* W RAP THE OPEN FLASHING AROUND THE PIPE. BRING THE TWO SIDES TOGETHER ALLOWING FOR A 2" OVERLAP. TRANSITION FROM VERTICAL TO HORIZONTAL FIRST, THEN THE VERTICAL, AND FINISH W ITH THE HORIZONTAL. Prefabricated Open Pipe Boot Detail #: PVC-1.21 LIGHTNING ROD STACK OR PROTRUSION (TYPICAL) GROUNDING CABLE ATTACHED TO ROD STACK FLASHING 3" SQUARE CABLE ANCHOR PLATE ROOF DECK (VULKEM) CAULK Lightning Rod Detail Detail #: PVC-1.22

14 METAL PIPE CAULK RAIN HOOD (BY OTHERS) WATERSTOP 1 1/2" HOT AIR CLAMPING RING INSULATION Pre-Fab Hot stack flashing Detail # PVC-1.23 PLATE W/ FASTENER 12" O.C. 4'X4' PATCH DRAIN 1 1/2" MIN HOT AIR W ELD CLAMPING RING DRAIN STRAINER CLAMPING BOLT INSULATION WATERSTOP NOTE: ALL BOLTS MUST BE PRESENT AND SECURE Sump Roof Detail Option Detail # PVC-1.24

15 CLAMPING RING DRAIN STRAINER WATERSTOP INSULATION NOTE: ALL BOLTS MUST BE PRESENT AND SECURE Existing/New Sump Roof Drain Detail # PVC-1.25 STRAINER INSERT FASTENER HOT AIR RETROFIT DRAIN INSERT INSULATION TREATED W OOD NAILER EXISTING DRAIN FASTENER Roof Drain Insert Detail # PVC-1.26

16 PLATE OR METAL BAR ANCHOR 4" MAX. FROM DECK W/OUT TREATED WOOD NAILER 1 1/2" HOT AIR FOAM TUBE CUSTOM FASTENER 12" O.C. FILLER NOTE: EXPANSION JOINTS MUST BE DONE ACCORDING TO INC. STANDARD DETAILS OR PRE- SHOP DRAWINGS. Flat Expansion Or Control Joint Detail # PVC-1.27 FOAM TUBING NAILS 12" O.C. 1 1/2" HOT AIR W ELD INSULATION TREATED W OOD NAILER FASTENER FILLER 18" O.C. MAX. Raised Expansion Joint Detail # PVC-1.28

17 BONDING ADHESIVE FASTENER 18" O.C. FOAM TUBE 2" SEAM PLATE OR METAL BAR ANCHOR WITH FASTENER 12" O.C. 1 1/2" HOT AIR SEPARATOR SHEET (SEE SYSTEM REQUIREMENTS) FILLER INSULATION 4" MAX. FROM DECK W /OUT WOOD NAILER Expansion Joint Base Of Wall Detail # PVC-1.29 TREATED W OOD NAILER METAL TERMINATION BAR WATERSTOP FASTENER 24" O.C. INSULATION GUTTER FASTENER EVERY HOLE WITH CAULK OR NEOPRENE WASHER Gutter Termination Detail # PVC-1.30

18 FASTENER EVERY HOLE SEALANT FASCIA COVER TREATED W OOD NAILER 2 3/4" FASCIA BAR INSULATION Custom Seal 2 3/4" Facsia Bar/Cover Detail # PVC-1.31 SEALANT FASTENER EVERY HOLE FASCIA COVER TREATED W OOD NAILER 2 3/4" FASCIA BAR (CREATES GRAVEL STOP) INSULATION 2 3/4" Fascia Bar Raised To Create Gravel Stop Detail # PVC-1.32

19 2" or 2 3/8" Seam Plates And Custom Seal Fasteners (PVC) Membrane 1 1/2" (3.8cm) Minimum Hot Air Weld (PVC) Membrane (maximum 37.5" width) 1 1/2" (3.8cm) Minimum Hot Air Weld (PVC) Coated Metal Insulation Continuous Metal Cleat Wood Nailer(s) (equal height to insulation and wider than the metal flange) Install metalwork in accordance with SMACNA recommendations 12/01 PVC Coated Metal Gravel Stop/Drip Edge Detail #: PVC-1.32a Custom Seal (PVC) Membrane Extending min. ½" Past Nailer Secured To The Nailer With The Spring Cleat Of The Snap On Fascia Assembly Custom Seal (PVC) Reinforced Flashing Or Field Cut (PVC) Membrane Of Sufficient Width To Achieve A 1½" Hot Air Weld Onto The Deck Sheet And Extend Over Dam And Down To Cleat Bend On Metal Spring Cleat Insulation Approved Substrate Fasten Spring Cleat Assembly In Accordance With Manufacturer's Recommendations But No Less Than 1 Fastener Every 6" Snap On Two Piece Fascia Assembly Detail #: PVC-1.32b

20 2" or 2 3/8" Seam Plates And Custom Seal Fasteners (PVC) Membrane 1 1/2" (3.8cm) Minimum Hot Air Weld (PVC) Membrane (maximum 37.5" width) (PVC) Coated Metal Insulation Continuous Metal Cleat Wood Nailer(s) (equal height to insulation and wider than the metal flange) 12/01 Install metalwork in accordance with SMACNA recommendations PVC Coated Metal Gravel Stop/Drip Edge Detail #: PVC-1.32c (PVC) Membrane Insulation 6" Wide (PVC) Reinforced Flashing (PVC) Coated Metal 1 1/2" (3.8cm) Minimum Hot Air Weld Continuous Metal Cleat Install metalwork in accordance with SMACNA recommendations (PVC) Coated Metal Gravel Stop / Drip Edge - Option 2 Detail #: PVC-1.32d

21 Cut opening into gravel stop fascia and dam leaving 1" minimum tabs on the 3 sides of the fascia that will connect with scupper sleeve. 2. Fabricate sleeve to fit opening Set tabs of sleeve in a bead of approved sealant onto the gravel stop / fascia and bend fascia tabs into the front of the sleeve into another bead of approved sealant and pop rivet into place as shown. Fabrication and assembly are to comply with SMACNA recommendations. 4. Strip in gravel stop flange according to system specification with the deck sheet Flash sleeve with unsupported flashing. 6. Treat metal joints in accordance with detail R Refer to appropriate edge detail for metal edge requirements - the focus of this detail is the fabrication of a gravelstop scupper. Gravelstop Scupper Fabricated With (PVC) Coated Metal Detail #: PVC-1.32e

22 TERMINATION BAR INSULATION WATERSTOP FASTENER EVERY HOLE Custom Seal Term Bar Over Edge Detail # PVC-1.33 WALKW AY PAD HEAT ED TO ( LONG SIDES ONLY) INSULATION Walkway Pad Detail # PVC-1.34

23 PROTECTION PAD PRECAST CONCRETE PAVERS 2"X2'X2' 85 lbs. MAX. INSULATION Concrete Walkway Paver Detail # PVC-1.35 PIPE OR CONDUIT TREATED W OOD SUPPORT INSULATION Pipe Support Detail # PVC-1.36

24 FLASHING AS RECOMMENDED BY OTHERS 1 1/2" MIN. HOT AIR PRODUCT SUPPLIED BY OTHERS INSULATION TREATED W OOD NAILER FASTENER 12" O.C. FASTENER 24" O.C. WATER STOP NOTE: SYSTEMS INC. DOES NOT W ARRANTY ANY TIE IN AREAS. System Tie-In Detail # PVC /2" MIN. HOT AIR W ELD BONDING ADHESIVE OR FASTENING TAB BAR ANCHOR OR 2" SEAM PLATE W/ FASTENER 12" O.C. INSULATION TO BE FASTENED EVERY 2 SQ. FT. IN THE ADHERED AREA Valley Tie-In Detail # PVC-1.38

25 1 1/2" MIN. HOT AIR W ELD METAL BAR ANCHOR OR 2" DISC W/ FASTENER 12" O.C. INSULATION NOTE: DESIGN FOR USE ON BUILDING UP TO 50'-0" IN HEIGHT System Tie-In Detail # PVC-1.39 THRESHOLD WATER STOP CAULK (SEE NOTE 2) BAR ANCHOR OR 2" SEAM PLATES W/ EACH 18" O.C. MAX. 1 1/2" HOT AIR W ELD INSULATION 4" MAX. FOR ATTACHMENT SHOW W/OUT WOOD NAILER Threshold Termination Detail # PVC-1.40

26 BREATHER VENT FACTORY W ELDED VENT SKIRT 1 1/2" HOT AIR INSULATION NOTE: 1. CUT MINIMUM OF 2 1/2" HOLE DOW N TO OR VAPOR BARRIER IF USED 2. MINIMUM 1 VENT PER 1000 SQ. FT. OR LESS Custom Seal Two Way Breather Vent Detail # PVC-1.41 Field Weld FACTORY W ELD Factory Weld Field Weld Factory Weld Field Weld FIELD Factory Weld Pre-Fab 12" Or Larger Stack Flashing Detail # PVC-1.42

27 FACTORY FACTORY HOT AIR HOT AIR HOT AIR HOT AIR FACTORY Custom Seal Pre-Fab Curb Flashing Detail # PVC 1-43 Custom Seal Reinforced Outside Corner Flashing Factory Welded Seam The flashing is manufactured with one side of the corner base tab factory welded to the deck and vertical portions of the flashing and one side loose to be field welded. This configuration allows the reinforced flashing to be adaptive to a less than perfect corner angle. Field Welded Seam Pre-Fab Outside Corner Detail # PVC-1.44

28 Custom Seal Bonding Adhesive Custom Seal TPO Membrane Custom Seal Insulation Approved Deck Custom Seal Reinforced Outside Corner Flashing Custom Seal Pre-Fab Outside Corner Detail # PVC FACTORY (TYP.) HOT AIR (TYP.) HOT AIR HOT AIR (TYP.) FACTORY (TYP.) FACTORY (TYP.) HOT AIR (TYP.) HOT AIR (TYP.) FACTORY VARIES Pre-Fab Scupper View 1 Detail # PVC-1.46

29 CAULK FLASHING FIELD CUT AROUND OPENING PARAPET METAL SCUPPER BOX VARIES PREFABRICATED SCUPPER Custom Seal Pre-Fab Supper View 2 Detail # PVC 1-47 PLATE OR ANCHOR BAR 1.5" FACTORY VARIES (100' MAX) 3" - 4" 75" 1.5" FACTORY FASTENING OVERLAP TOP OR BOTTOM 75" VARIES 1.5" FACTORY 37.5" Typical Factory Pre-Fab Panel - Detail Detail # PVC 1-48

30 Cut opening into gravel stop fascia and dam leaving 1" minimum tabs on the 3 sides of the fascia that will connect with scupper sleeve. 2. Fabricate sleeve to fit opening Set tabs of sleeve in a bead of approved sealant onto the gravel stop / fascia and bend fascia tabs into the front of the sleeve into another bead of approved sealant and pop rivet into place as shown. Fabrication and assembly are to comply with SMACNA recommendations. 4. Strip in gravel stop flange according to system specification with the deck sheet Flash sleeve with unsupported flashing. 6. Treat metal joints in accordance with detail R Refer to appropriate edge detail for metal edge requirements - the focus of this detail is the fabrication of a gravelstop scupper. Gravelstop Scupper Fabricated With (PVC) Coated Metal Detail #: PVC-1.47A

31 PLATE OR ANCHOR BAR 1.5" FACTORY VARIES (100' MAX) 75" 3" - 4" 1.5" FACTORY 75" VARIES FASTENING OVERLAP TOP OR BOTTOM 1.5" FACTORY 75" Typical Factory Pre-Fab Panel - Detail Detail # PVC 1-49 VARIES (100' MAX) 1.5" FACTORY BUTT 12' 1.5" FACTORY SKIRT ON TOP 6" FIELD 3" 12' 1.5" FACTORY BUTT SKIRT ON TOP 6" 1.5" FACTORY FIELD 3" FASTENERS ARE SPACED 6" O/C WITH ANCHOR BAR 12' O/C. 12'6" Tab System Or 24'6" Tab System Detail # PVC 1-50

32 Custom Seal Roofing - Installed Per Custom Seal Spec's. Bead Board Filler Pre-Cut To Fit Width In Metal Roof Deck 1" (Min) Iso (4' X 8") 6 Screws & Plates Per Sheet Custom Seal Membrane Re-Roof Over Standing Seam Metal Roof Detail # PVC 1-51