Internetwork Node Controller

Transcription

1 J8 J9 B ET J7 J J5 A Dev B Dev A Internetwork Node Controller Important Retain these instructions Contents Unpacking... Storage... 3 Installation 3. Installation - Mounting Installation - Configuration... Disposal... 8 Unpacking, TG003 Storing -0 C ( F) +50 C ( F) %RH 3 Installation 3. Installation - Mounting Dimensions 0 mm (.3") It is recommended that the installation should comply with the HSE Memorandum of Guidance on Electricity at Work Regulations 989. For USA install equipment in accordance with the National Electric Code. 5 mm (5.9") & ' WARNING Opening the panel may expose dangerous voltages. 7-IEC-503 Caution The contains static sensitive devices. Suitable anti-static precautions should be taken throughout this operation to prevent damage to the unit. BS EN0005/ Basic Specification protection of electostatic sensitive devices. = * = ) 33 mm (.38") TG003Issue /E 09//0

2 & & ' = * = ) ' = * = ) + & ' = * = ) 3. Installation - Mounting (Continued) Requirements a b 0 C (3 F) +5 C (3 F) 0 0 %RH 95 %RH d c /USA The unit is UL rated as 'UL9 accessory to open energy management equipment'. Mount the Node The can be fitted into enclosures and controllers as shown in the table below NETB/NETBB IQ0+/0+ IQ+ IQ3+ IQ5x IQ/ IQ3/33 * * board fits with 3 screws in normal node position or fits in NDP position (if no NDP). Must use NDP position if RDS fitted. 5 mm (5.9") mm (5.55") off mm See appropriate enclosure/controller installation instructions for more details about node installation. 3 Connecting Power ~ ~ 0V Vdc consumption <=5 VA + V 0V ~ ~ 0V Vac ~ ~ 0V 8 Vac (isolated) & ' DO NOT APPLY POWER = * = ) 8 Vac terminal size 0.5 to.5 mm ( to 0 AWG) TG003Issue /E 09//0

3 3. Installation - Mounting (Continued) Connecting Earth (ground) & ' = * = ) WARNING This apparatus must be earthed (grounded) 5 Connect Network ( A) (unless RS3 receiver/transmitter Device A being used e.g. leased line modem) Normally Local dumb/normal switch set to dumb, any address dumb/normal switch set to normal, address <00 Note that EINCs, INCs and LINCs cannot be on same Internetwork segment A if dumb/normal switch set to normal (internetwork buffer), address >=00 Network Engineering Manual, & ' = * = ) Cable k k8 9k 9k No. of Wires Belden m 000 m 000 m 700 m (090 yds) (090 yds) (090 yds) (75 yds) Belden m 000 m 000 m 500 m (090 yds) (090 yds) (090 yds) (55 yds) IQ system TP////HF/ m 000 m 700 m 350 m (Belden 87) (090 yds) (090 yds) (75 yds) (380 yds) IQ system TP////HF/ m 000 m 500 m 50 m (Belden 873) (090 yds) (090 yds) (55 yds) (70 yds) polarity independent wire LAN A terminal size 0.5 to.5 mm ( to 0 AWG) wire additional terminals LAN A additional terminals Connect Network ( B) (unless RS3 receiver/transmitter Device B being used e.g. leased line modem) Always Internetwork terminal size 0.5 to.5 mm ( to 0 AWG) Network Engineering Manual, Cable k k8 9k 9k 38k No. of Wires Belden m 000 m 000 m 700 m 500 m (090 yds) (090 yds) (090 yds) (75 yds) (55 yds) Belden m 000 m 000 m 500 m 350 m (090 yds) (090 yds) (090 yds) (55 yds) (380 yds) IQ system TP////HF/ m 000 m 700 m 350 m 50 m (Belden 87) (090 yds) (090 yds) (75 yds) (380 yds) (70 yds) IQ system TP////HF/ m 000 m 500 m 50 m 5 m (Belden 873) (090 yds) (090 yds) (55 yds) (70 yds) (35 yds) polarity independent wire LAN B / IWRK wire & ' = * = ) LAN B / IWRK additional terminals TG003Issue /E Draft 09//0 3

4 & ' = * = ) 3. Installation - Mounting (Continued) 7 Close Panel/Box /USA The unit is UL rated as 'UL9 accessory to open energy management equipment'. 3. Installation - Configuration Switch off and open panel/covers WARNING Opening the panel may expose dangerous voltages. 7-IEC-503 /USA The unit is UL rated as 'UL9 accessory to open energy management equipment'. Caution The contains static sensitive devices. Suitable anti-static precautions should be taken throughout this operation to prevent damage to the unit. BS EN0005/ Basic Specification protection of electostatic sensitive devices. Set Dumb/Normal switch e.g. ),, - 5 5, 7 * Dumb Sets traditional INC only mode (/Internetwork gateway, A always a, never Internetwork) Norm Sets Internetwork repeater or /Internetwork gateway dependent on address (see step below) TG003Issue /E 09//0

5 & ' = * = ) & ' = * = ) 3. Installation - Configuration (Continued) 3 Set the Internetwork Address ( number) Set A Network Baud Rate (or Device A RS3 rate if connected to RS3 receiver/transmitter) Baud A e.g. ),, SET NOT SET, 7 * Address = ++= 8 address, to 9, to 0,, 3, 0 or >9 D Address = D = D D D move link to set rate (Baud A) Network Baud Rate = R (or RS3 to DeviceA) = R if dumb (traditional INC only mode) address defines number on Internetwork (/Internetwork gateway) if normal if address < 00, address defines number on Internetwork (/Internetwork gateway) A B Internetwork e.g 9k = R = R = R if address = > 00, address is for configuration only (Internetwork repeater) Internetwork A B Internetwork Segment A Segment B 5 Set B Internetwork Baud Rate (or Device B RS3 rate if connected to RS3 receiver/transmitter) move link to e.g 9k set rate Baud B (Baud B) Internetwork Baud Rate = R (or RS3 to Device B) & ' = * = ) Note needs extra link or High Baud Rate, 38k Note that 38k is only supported if connecting to other node devices (e.g. 3xtend/EINC L) communicating over the internetwork. This rate is not supported through the LAN A terminals. = R = R = R = R TG003Issue /E Draft 09//0 5

6 & ' = * = ) & ' = * = ) & ' = * = ) 3. Installation - Configuration (Continued) 0 Way, Female, Molex links between pins -, 3-5 Connect to RS3 Device A if Device A is a RS3 receiver/transmitter (e.g. leased line modem) Note Connecting a cable to an RS3 connector disables corresponding communications. J5 Dev A CABLE/EJ0079A00 not supplied Dev A J5 Device A Receiver/ Transmitter 5 Way, Female, 'D type' black sheath 7 0 Way, Female, Molex links between pins -, 3-5 Connect to RS3 Device B if Device B is a RS3 receiver/transmitter (e.g. leased line modem) J Dev B/ Modem Dev B/Modem Note Connecting a cable to an RS3 connector disables corresponding communications. CABLE/EJ0079A00 not supplied Device B Receiver/ Transmitter 5 Way, Female, 'D type' J black sheath 8 Switch On 9 Check Node Controller a PWR ON (green) Check input power b W/DOG (red) Faulty 0 Check A Not if RS3 receiver/transmitter connected to Dev A a RXA (yellow) + b TXA (yellow) + & ' = * = ) c OKA (green) Network Address Invalid 0,, 3 or >9 LAN A OKA Faulty LAN A OKA Check network cabling for short circuits with a multimeter (NOT Megger) Check rate. Power up other nodes until faulty node is found (OK ). Correct fault. TG003Issue /E 09//0

7 3. Installation - Configuration (Continued) Check B Not if RS3 receiver/transmitter connected to Dev B a RXB (yellow) + b TXB (yellow) + & ' = * = ) c OKB (green) Network Address Invalid 0,, 3 or >9 LAN B / IWRK OKB Faulty LAN B / IWRK OKB Check network cabling for short circuits with a multimeter (NOT Megger) Check rate. Power up other nodes until faulty node is found (OK ). Correct fault. Close panel/covers /USA The unit is UL rated as 'UL9 accessory to open energy management equipment'. Top Menu User address Network Engineering Manual IQ Configuration Manual Data Sheet TA Configure Recommend use of SET e.g. select address module Select from lanmap or set addresses as below If on local, or autodialled, set = 0, address = (Note address used for old INC,, address, still works) If using Internetwork, or autodialled remote, set = switch setting, address = to exit module having changed parameter to Quit module and discard changes 3 Note that a PIN may be required to make changes in configuration mode. If the PIN has been forgotten the user should contact Trend Technical Support quoting the generator number (User module) whereupon a default PIN will be supplied. This will only work during the same configuration mode session i.e. the utility must not be exited between reading the generator and entering the default PIN. After the PIN is entered a new PIN should be set up and remembered. TG003Issue /E Draft 09//0 7

8 3. Installation - Configuration (Continued) Settings that may be changed Set up following parameters if required Parameter Setting Function Condition Note address User identifier Local Network alarms to Internetwork alarms to Address Remote lan address alarm language type remote lan Pin generator 5 alphanumeric characters - not /\({;?* characters Identifier for the lan ( A) Always set for supervisors/display Panels node address, to 9, to node address of alarm target If A alarms to be reported 9 for A alarms number, to 9, to number of alarm target If A alarms to be reported 9 for A alarms node address, to 9, to node address of alarm target If B alarms to be reported 9 for B alarms number, to 9, to number of alarm target If B alarms to be reported 9 for B alarms 0 to 9 (digits) Selects language of network If language to be changed alarms number Protects changes in configuration Default is blank (unprotected). Set mode up if security required. number random number for default PIN Read only, give to TechniCare for generation default PIN. If set to zero - no alarms reported. guage type values 0=English, =Spanish, =Finnish, 3=Swedish, =Norwegian, 5=Danish, =German, 7=Italian, 8=Portuguese, 9=French. 5 Exit Configuration "Exit from Utility" Check Operation If /Internetwork Gateway /Internetwork Gateway ( C or D) If Internetwork Repeater (dumb/normal = normal and address =>00) Internetwork Repeater ( E) Internetwork IQ C D Internetwork Internetwork Segment Segment A B C E D IQ Disposal WEEE Directive At the end of their useful life the packaging, and product, should be disposed of by a suitable recycling centre. Do not dispose of with normal household waste. Do not burn. Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell Technologies Sàrl, Ecublens, Route du Bois 37,Switzerland by its Authorized Representative, Trend Control Systems Limited. Trend Control Systems Limited reserves the right to revise this publication from time to time and make changes to the content hereof without obligation to notify any person of such revisions or changes. Trend Control Systems Limited P.O. Box 3, Horsham, West Sussex, RH YF, UK. Tel+ (0) Fax+ (0) Trend Control Systems USA 70 85th Avenue NE, Redmond, Washington 9805, USA. Tel (5) , Fax (5) TG003Issue /E 09//0